Login- Download PDF Manual
-
! Do not clean the lens of the Night View Assist Plus camera. If the camera lens is dirty, please contact an authorized Mercedes-Benz Center.
X Use recessed handle : of camera cover to
swing camera cover downward.
X Clean inside of windshield in front of camera ; with a soft, non-scratching cloth.
! If you use a windshield cleaning product,
make sure that none of the cleaning product comes into contact with the lens of the Night View Assist Plus camera.
X Use recessed handle : of camera cover to
swing camera cover up.
2009-07-17T09:14:21+02:00 - Seite 264
Version: 2.11.8.1Cleaning the windows and the wiper blades ! Never open the hood when the wiper arms
are folded forward. G Warning! For safety reasons, switch off wipers and remove SmartKey from starter switch before cleaning the windshield and/or the wiper blades. Vehicles with KEYLESS-GO: Make sure the vehicle’s on-board electronics have status 0. Otherwise, the wiper motor could suddenly turn on and cause injury.
! Do not pull on the wiper blade inserts.
They could tear.
X Fold the wiper arms forward until they snap
into place.
X Clean the windshield and the wiper blade
inserts with a clean cloth and mild detergent solution.
X Use a soft, clean cloth and a mild window cleaning solution on all outside and inside glass surfaces. An automotive glass cleaner is recommended.
! Fold the windshield wiper arms back onto the windshield before turning the SmartKey in the starter switch or pressing the KEYLESS-GO start/stop button. Hold on to the wiper when folding the wiper arm back. If released, the force of the impact from the tensioning spring could crack the windshield.
! To clean the window interior, do not use a dry cloth, abrasives, solvents or cleaners containing solvents. Do not touch the inside of the windows with hard objects such as an ice scraper or ring. Doing so may damage the windows.
212_AKB; 2; 41, en-US d2ureepe,
2009-07-17T09:14:21+02:00 - Seite 265
Version: 2.11.8.1Cleaning the panorama roof The rear part of the tilt/sliding panel has a protective layer on the inside. X Use a soft, clean cloth and a mild window
cleaning solution. An automotive glass cleaner is recommended.
! Do not use a dry cloth, abrasives, solvents
or cleaners containing solvents. Do not touch the protective layer with hard objects such as an ice scraper or ring. Never apply strong force and only use a soft, non- scratching cloth when cleaning the rear part of the tilt/sliding panel. Otherwise you may scratch or damage the protective layer.
Light alloy wheels If possible, clean wheels once a week. X Use Mercedes-Benz approved Wheel Care,
a soft bristle brush and a strong spray of water for cleaning the light alloy wheels. ! Only use acid-free cleaning materials.
Acid may cause corrosion or damage the clear coat.
! The vehicle should not be parked for an extended period of time immediately after it has been cleaned. This applies especially after the wheel rims have been cleaned with wheel rim cleaner. Wheel rim cleaners can lead to increased corrosion of the brake disks and brake pads. Non-approved wheel cleaners may also damage the wheel paint if the vehicle is not driven after cleaning. Therefore, the vehicle’s brake system should always be warmed-up before it is parked after cleaning. Drive your vehicle for several minutes to allow the brakes to dry. When applying Mercedes-Benz approved Tire Care and Mercedes-Benz approved Wheel Care products, take care not to spray them on the brake disks.
Vehicle care 265
Plastic and rubber parts X Use a gentle dishwashing detergent or mild detergent for delicate fabrics as a washing solution.
X Wipe with a cloth moistened in a lukewarm
solution. The surface may temporarily change color. If this is the case, wait for it to dry. G Warning! Do not use cleaners or cockpit care sprays containing solvents to clean the cockpit or the steering wheel. Cleaners containing solvents will make the surface porous and vehicle occupants could suffer serious injuries from plastic parts coming loose in the event of air bag deployment.
! Do not use oil, wax or scouring agents.
Otherwise you may scratch or damage the surface.
Hard plastic trim items X Use Mercedes-Benz approved Interior Care on a soft, lint-free cloth and apply with light pressure.
COMAND display ! You must switch off the COMAND display
and allow it to cool prior to cleaning.
! Do not use any liquids or cleaning agents.
These can damage or even destroy the COMAND display screen.
X Use a standard microfiber cloth and apply
with light pressure.
Steering wheel and gear selector lever X Wipe with a damp cloth and dry thoroughly
or clean with Mercedes-Benz approved Leather Care.
212_AKB; 2; 41, en-US d2ureepe,
266 Vehicle care
2009-07-17T09:14:21+02:00 - Seite 266
Version: 2.11.8.1Carpets X Use Mercedes-Benz approved Carpet and
Fabric Care for cleaning the carpets.
Headliner and shelf below rear window X Use a soft bristle brush or a dry-shampoo
cleaner in case of excessive dirt.
Seat belts X Only use clear, lukewarm water and soap. ! The seat belts must not be treated with chemical cleaning agents. Do not dry the seat belts at temperatures above 176‡ (80†) or in direct sunlight. G Warning! Do not bleach or dye seat belts as this may severely weaken them. In a crash they may not be able to provide adequate protection.
Upholstery Using aftermarket seat covers or wearing clothing that have the tendency to give off coloring (e.g. when wet, etc.) may cause the upholstery to become permanently discolored. By lining the seats with a proper intermediate cover, contact-discoloration will be prevented. G Warning! Only use seat or head restraint covers which have been tested and approved by Mercedes- Benz for your vehicle model. Using other seat or head restraint covers may interfere with or prevent Rdeployment of the front side impact air
bags
Rdeployment of the rear side impact air bags Rdeployment of the pelvis air bags Ractivation of the NECK-PRO active front
head restraints
Contact an authorized Mercedes-Benz Center for availability. Leather upholstery Please note that leather upholstery is a natural product and is therefore subject to a natural aging process. Leather upholstery may also react to certain ambient influences such as high humidity or high temperature by showing wrinkles for example. X Wipe leather upholstery with a damp cloth and dry thoroughly or clean with Mercedes- Benz approved Leather Care.
! To avoid damage to leather upholstery:
RWipe with light pressure only. RDo not clean with abrasive cleaning
agents such as scouring milk or powder.
RDo not soak the leather upholstery.
As leather is a natural product, it could otherwise harden or become porous. RExercise particular care when cleaning
perforated leather as its underside should not become wet.
Wood trims X Only use water and a damp cloth to clean
wood trims in your vehicle.
! Do not use solvents like tar remover or wheel cleaner nor polishes or waxes as these may be abrasive.
Chrome-plated exhaust tip Regular cleaning and care of chrome-plated exhaust tips will help to maintain their shine and the classy appearance. X Use Mercedes-Benz approved Chrome
Polishing Paste each time the vehicle has been washed, especially during the winter.
! Do not use alkaline cleaners such as
wheel cleaners as they could cause corrosion.
212_AKB; 2; 41, en-US d2ureepe,
2009-07-17T09:14:21+02:00 - Seite 267
Version: 2.11.8.1267
Vehicle equipment ............................ 268
Where will I find ...? .......................... 268
Vehicle status messages in the multifunction display ....................... 272
What to do if … .................................. 304
Unlocking/locking manually ........... 314
Resetting activated NECK-PRO active front head restraints ............. 316
Replacing SmartKey batteries ......... 317
Replacing bulbs ................................. 318
Replacing wiper blades .................... 322
Flat tire .............................................. 323
Bleeding the fuel system (diesel engine only) ....................................... 333
AdBlue® (diesel engine only) ........... 333
Battery ............................................... 336
Jump starting .................................... 338
Towing the vehicle ............................ 340
Fuses .................................................. 343212_AKB; 2; 41, en-US d2ureepe,
2009-07-17T09:14:21+02:00 - Seite 268
Version: 2.11.8.1268 Where will I find ...?
Vehicle equipment
i This Operator’s Manual describes all
features, standard or optional, potentially available for your vehicle at the time of purchase. Please be aware that your vehicle might not be equipped with all features described in this manual.
Where will I find ...? First aid kit i Check expiration dates and contents for
completeness at least once a year and replace missing/expired items.
The first-aid kit is located in the trunk on the right-hand side behind the cover.
wrench. Some tools required for a wheel change are specific to your vehicle. Contact an authorized Mercedes-Benz Center to obtain the tools approved for your vehicle.
The vehicle tool kit includes: RCollapsible wheel chock16
RElectric air pump17,18
RFuse chart RJack16
RPair of gloves16
RProtective wrap17
RTIREFIT kit18
RTowing eye bolt RWheel wrench16
X Open the trunk (Y page 81).X Lift the trunk floor using floor handle :.
X Turn the lock clockwise and fold down the
cover.
X Loosen tensioning strap :.
First aid kit ; can be removed.
Vehicle tool kit The vehicle tool kit is located in the space underneath the trunk floor. i Vehicles without spare wheel are not
factory-equipped with the tools required for a wheel change such as a jack or a wheel
16 Vehicles with spare wheel only. 17 E 63 AMG 18 E 350 BlueTEC (if so equipped)
212_AKB; 2; 41, en-US d2ureepe,
2009-07-17T09:14:21+02:00 - Seite 269
Version: 2.11.8.1Where will I find ...?
269
E 350 BlueTEC : TIREFIT kit ; Electric air pump = Jack ? Towing eye bolt A Wheel wrench B Fuse chart C Collapsible wheel chock D Alignment bolt
Vehicles with spare wheel All models except E 63 AMG
X Engage floor handle = on upper trunk
lip ;.
Vehicles without spare wheel i Vehicles without spare wheel are not
factory-equipped with the tools required for a wheel change such as a jack or a wheel wrench. Some tools required for a wheel change are specific to your vehicle. Contact an authorized Mercedes-Benz Center to obtain the tools approved for your vehicle. The illustration shows the vehicle retrofitted with the necessary tools for a wheel change.
i USA only: Vehicles with MOExtended system are not factory-equipped with a TIREFIT kit. When retrofitting with tires that do not have run-flat characteristics, you should also equip your vehicle with a TIREFIT kit. TIREFIT kits are available at any authorized Mercedes-Benz Center.
: Tab ; Removing vehicle tool kit box = Vehicle tool kit box cover A Opening vehicle tool kit box cover B Tab C Vehicle tool kit D Vehicle tool kit box E Luggage bowl
212_AKB; 2; 41, en-US d2ureepe,
2009-07-17T09:14:21+02:00 - Seite 270
Version: 2.11.8.1270 Where will I find ...?
X Removing vehicle tool kit box: Pull tab : in direction of arrow ; and lift vehicle tool kit box D.
X Remove vehicle tool kit box D from
luggage bowl E.
X Opening vehicle tool kit box cover: Pull tab B in direction of arrow A and open vehicle tool kit box cover =.
X Closing vehicle tool kit box cover: Push
vehicle tool kit box cover = downward until it engages into vehicle tool kit box D.
X Installing vehicle tool kit box: Slide
vehicle tool kit box D into the recess of luggage bowl E.
X Push vehicle tool kit box D downward until
it engages into luggage bowl E.
E 63 AMG
: Towing eye bolt ; Pair of gloves = Jack ? Collapsible wheel chock A Alignment bolt B Protective wrap C Electric air pump D Wheel wrench E Fuse chart
Collapsible wheel chock The collapsible wheel chock serves to secure the vehicle, e.g. while changing a wheel.
X Take the collapsible wheel chock from the
vehicle tool kit (Y page 268).
X Setting up: Tilt both plates upward :. X Fold the lower plate outward ;. X Guide the tabs of the lower plate all the way
into the openings of base plate =.
For information on where to place wheel chocks when changing a wheel, see “Lifting the vehicle” (Y page 324).
Jack G Warning! Only use the jack supplied with your vehicle to lift the vehicle briefly for wheel changes. If you use the jack for any other purpose, you or others could be injured, as the jack is designed only for the purpose of changing a wheel. When using the jack, observe the safety notes in the “Mounting the spare wheel” section and the notes on the jack.
X Take the jack from the vehicle tool kit
(Y page 268).
212_AKB; 2; 41, en-US d2ureepe,
2009-07-17T09:14:21+02:00 - Seite 271
Version: 2.11.8.1Where will I find ...?
271
! To prevent damage, always disengage the
floor handle from the upper trunk lip and lower the trunk floor before closing the trunk.
All models except E 63 AMG
X Removing: Remove luggage bowl ; by
turning it counterclockwise.
X Remove spare wheel :.
Storing the spare wheel after use X Place spare wheel : into the spare wheel
well.
X Secure spare wheel : by turning luggage
bowl ; clockwise.
E 63 AMG
X Removing: Reach into recess : of
storage well casing to pull it up and remove it.
X Remove spare wheel ;.
Storage position X Turn the crank handle in the direction of
arrow as far as it will go.
Operational position X Turn the crank handle clockwise. Before placing the jack back into the vehicle tool kit: X Fully collapse the jack. X Fold in the crank handle (storage position).
Spare wheel G Observe Safety notes, see page 323. i The E 350 BlueTEC does not have a spare
wheel.
The spare wheel is located in the space underneath the trunk floor. X Removing: Open the trunk (Y page 81). X Lift the trunk floor and secure it on the
upper trunk lip (Y page 268).
212_AKB; 2; 41, en-US d2ureepe,
2009-07-17T09:14:21+02:00 - Seite 272
Version: 2.11.8.1272 Vehicle status messages in the multifunction display
Storing the spare wheel after use If you wish to store the spare wheel after use, carry out the following steps. Otherwise, the spare wheel may not fit into the spare wheel well. ! Make sure the spare wheel is dry before
storing it.
X Unscrew the valve cap from the valve of the
collapsible tire.
X Unscrew the valve insert from the valve
using the valve extractor integrated in the valve cap.
X Allow the air to escape. i It may take a few minutes for the
collapsible tire to deflate completely.
X Screw the valve insert back into the valve. X Screw the valve cap back onto the valve. X Take the protective wrap from the vehicle
tool kit (Y page 268).
X Pull the protective wrap over the spare
wheel.
X Place the spare wheel into the spare wheel
well.
Vehicle status messages in the multifunction display Notes Warning and malfunction messages appear in the multifunction display located in the instrument cluster. Certain warning and malfunction messages are accompanied by an audible signal. Address these messages accordingly and follow the additional instructions given in this Operator’s Manual. High-priority messages appear in the multifunction display in red color. Certain messages of high priority cannot be cleared from the multifunction display using a or % on the multifunction steering wheel (Y page 126).
Other messages of high priority and messages of less immediate priority can be cleared from the multifunction display using a or %. They are then stored in the vehicle status message memory (Y page 139). Remember that clearing a message will only make the message disappear. Clearing a message will not correct the condition that caused the message to appear. G Warning! All categories of messages contain important information which should be taken note of and, where a malfunction is indicated, addressed as soon as possible at an authorized Mercedes-Benz Center. Failure to repair the condition noted may cause damage not covered by the Mercedes- Benz Limited Warranty, or result in property damage or personal injury. G Warning! No messages will be displayed if either the instrument cluster or the multifunction display is inoperative. As a result, you will not be able to see information about your driving conditions, such as Rspeed Routside temperature Rwarning/indicator lamps Rmalfunction/warning messages Rfailure of any systems Driving characteristics may be impaired. If you must continue to drive, do so with added caution. Contact an authorized Mercedes- Benz Center as soon as possible. Read and observe the notes on the HOLD function (Y page 161) and parking (Y page 113) when you park the vehicle. On the pages that follow, you will find a compilation of the most important warning and malfunction messages that may appear.
212_AKB; 2; 41, en-US d2ureepe,
2009-07-17T09:14:21+02:00 - Seite 273
Version: 2.11.8.1Vehicle status messages in the multifunction display
273
For your convenience the messages are divided into text messages (Y page 274) and symbol messages (Y page 287).
212_AKB; 2; 41, en-US d2ureepe,
2009-07-17T09:14:21+02:00 - Seite 274
Version: 2.11.8.1274 Vehicle status messages in the multifunction display
Text messages Safety systems
Display messages PRE-SAFE
Inoperativ e See Operator's Manual Functions Currently Limited See Operator's Manual
PRE-SAFE
Possible causes/consequences and M Solutions The PRE-SAFE® system has failed. All other occupant safety systems, such as the air bags, are still available. X Contact an authorized Mercedes-Benz Center as soon as
possible.
The PRE-SAFE® Brake is temporarily unavailable. The PRE-SAFE® Brake is deactivated because: Rthe DISTRONIC PLUS cover in the radiator grille is dirty Rthe area around the sensors in the front or the rear bumper
is dirty
Rits function is impaired as a result of heavy precipitation Rthe radar sensor system is temporarily inoperative due to
electromagnetic interference near television and radio transmitter stations, toll stations, speed measuring systems, etc.
Rthe system is out of the operating temperature range Rthe battery voltage is insufficient RE 63 AMG only: The ESC has been switched off. The PRE-SAFE® Brake becomes operational again and the message in the multifunction display disappears when: Rdirt on the radiator grille has fallen off while driving (e.g.
slush or snow)
Rthe system recognizes full sensor availability (due to
lessening rain or the road surface drying)
Rthe system is within the operating temperature range RE 63 AMG only: The ESC is switched back on. If the message in the multifunction display does not disappear: X Clean the DISTRONIC PLUS cover in the radiator grille
(Y page 263).
X Clean the front and the rear bumper (Y page 263). X Restart the vehicle. X Wait until the battery recovers.
212_AKB; 2; 41, en-US d2ureepe,
2009-07-17T09:14:21+02:00 - Seite 275
Version: 2.11.8.1Vehicle status messages in the multifunction display
275
Display messages PRE-SAFE
Functions Limited See Operator's Manual
Possible causes/consequences and M Solutions The PRE-SAFE® Brake is unavailable due to a malfunction. The BAS PLUS may also be unavailable. X Contact an authorized Mercedes-Benz Center as soon as
possible.
212_AKB; 2; 41, en-US d2ureepe,
2009-07-17T09:14:21+02:00 - Seite 276
Version: 2.11.8.1276 Vehicle status messages in the multifunction display
Display messages Front Passenger Airbag Enabled See Operator’s Manual
Possible causes/consequences and M Solutions USA only: The front passenger front air bag is activated while driving even though a child, small individual, or object below the system’s weight threshold is on the front passenger seat, or the front passenger seat is empty. Objects on the seat or forces acting on the seat may make the system sense supplemental weight. X Stop the vehicle in a safe location as soon as possible. X Engage the parking brake. X Switch off the ignition. X Open the front passenger door. X Remove child and child restraint from front passenger seat
and properly secure the child in rear seat employing the child restraint if necessary.
X Make sure no objects which apply supplemental weight to
the seat are present. The system may recognize such supplemental weight and sense that an occupant on the front passenger seat is of a greater weight than actually present.
X Keep the seat unoccupied, close the front passenger door
and switch on the ignition.
Monitor the 45 indicator lamp in the center console (Y page 45) and the multifunction display in the instrument cluster (Y page 28) for the following: With the seat unoccupied and the ignition switched on, Rthe 45 indicator lamp in the center console should illuminate and remain illuminated, indicating that the OCS (Y page 43) has deactivated the front passenger front air bag. Rthe message Front Passenger Airbag Enabled See Operator’s Manual or the message Front Passenger Airbag Disabled See Operator’s Manual should not appear in the multifunction display at any time the seat is unoccupied. Wait at least 60 seconds for the system to complete the necessary check cycles and to make sure neither message appears in the multifunction display.
If above conditions are met, you can occupy the front passenger seat again. Depending on the front passenger classification sensed by the OCS, the 45 indicator lamp will remain illuminated or go out.
212_AKB; 2; 41, en-US d2ureepe,
2009-07-17T09:14:21+02:00 - Seite 277
Version: 2.11.8.1Vehicle status messages in the multifunction display
277
Display messages
Possible causes/consequences and M Solutions If above conditions are not met, the system is not working properly. Have the system checked at an authorized Mercedes-Benz Center as soon as possible.
G Warning! If the 45 indicator lamp remains out even after performing the above corrective steps, do not have any children 12 years old and under and other small individuals use the passenger seat until the system has been repaired.
212_AKB; 2; 41, en-US d2ureepe,
2009-07-17T09:14:21+02:00 - Seite 278
Version: 2.11.8.1278 Vehicle status messages in the multifunction display
Display messages Front Passenger Airbag Disabled See Operator’s Manual
Possible causes/consequences and M Solutions USA only: The front passenger front air bag is deactivated while driving even though an adult or someone larger than a small individual is occupying the front passenger seat. Forces acting on the seat may make the system sense a decrease in weight. X Stop the vehicle in a safe location as soon as possible. X Engage the parking brake. X Switch off the ignition. X Have the front passenger vacate the seat and exit the
vehicle.
X Keep the seat unoccupied, close the front passenger door
and switch on the ignition.
Monitor the 45 indicator lamp in the center console (Y page 45) and the multifunction display in the instrument cluster (Y page 28) for the following: With the seat unoccupied and the ignition switched on, Rthe 45 indicator lamp in the center console should illuminate and remain illuminated, indicating that the OCS (Y page 43) has deactivated the front passenger front air bag. Rthe message Front Passenger Airbag Enabled See Operator’s Manual or the message Front Passenger Airbag Disabled See Operator’s Manual should not appear in the multifunction display at any time the seat is unoccupied. Wait at least 60 seconds for the system to complete the necessary check cycles and to make sure neither message appears in the multifunction display.
If above conditions are met, you can occupy the front passenger seat again. Depending on the front passenger classification sensed by the OCS, the 45 indicator lamp will remain illuminated or go out. If above conditions are not met, the system is not working properly. Have the system checked at an authorized Mercedes-Benz Center as soon as possible.
212_AKB; 2; 41, en-US d2ureepe,
2009-07-17T09:14:21+02:00 - Seite 279
Version: 2.11.8.1Vehicle status messages in the multifunction display
279
Display messages Check See Operator's Child Manual Seat Position
Possible causes/consequences and M Solutions Vehicles with BabySmart™ (Canada only): The BabySmart™ child seat is not positioned correctly. Risk of injury! X Install the BabySmart™ child seat in correct position. Vehicles with BabySmart™ (Canada only): The sensor for child seat recognition is malfunctioning. Risk of injury! X Contact an authorized Mercedes-Benz Center.
G Warning! If the 45 indicator lamp remains illuminated with an adult occupant on the front passenger seat even after performing the above corrective steps, do not have any passenger use the front passenger seat until the system has been repaired.
Driving systems
Display messages Cruise Control
Inoperativ
Cruise Control
- - - mph
Possible causes/consequences and M Solutions The cruise control is malfunctioning. In addition an acoustic warning sounds. X Have the cruise control checked at an authorized
Mercedes-Benz Center.
One of the activation conditions for cruise control has not been fulfilled. You may have attempted to set a speed below 20 mph (30 km/h). X Drive faster than 20 mph (30 km/h) if the situation allows
and set the speed.
X Check the activation conditions for cruise control
(Y page 147).
212_AKB; 2; 41, en-US d2ureepe,
2009-07-17T09:14:21+02:00 - Seite 280
Version: 2.11.8.1280 Vehicle status messages in the multifunction display
Display messages DISTRONIC PLUS
Currently Unavailabl e See Operator's Manual
Possible causes/consequences and M Solutions The DISTRONIC PLUS is temporarily unavailable. The DISTRONIC PLUS is deactivated because: Rthe DISTRONIC PLUS cover in the radiator grille is dirty Rits function is impaired as a result of heavy precipitation Rthe radar sensor system is temporarily inoperative due to
electromagnetic interference near television and radio transmitter stations, toll stations, speed measuring systems, etc.
Rthe radar sensors do not sense any other vehicles or objects, i.e. road sign or similar to this, for a long time Rthe system is out of the operating temperature range Rthe battery voltage is insufficient X If necessary, clean the DISTRONIC PLUS cover in the
radiator grille (Y page 263).
X Restart the vehicle. X Try activating the DISTRONIC PLUS again later. X Wait until the system is within the operating temperature
range or the battery recovers.
The DISTRONIC PLUS becomes operational again without the engine being restarted when: Rdirt on the radiator grille has fallen off while driving (e.g.
slush or snow)
Rthe system recognizes full sensor availability (due to
lessening rain or the road surface drying)
Rthe message in the multifunction display disappears
The DISTRONIC PLUS is malfunctioning. The BAS PLUS and the PRE-SAFE® Brake are also not available. X Contact an authorized Mercedes-Benz Center as soon as
possible.
You have accelerated. The DISTRONIC PLUS has switched off. X Stop accelerating.
DISTRONIC PLUS
Inoperativ
DISTRONIC PLUS
Override
212_AKB; 2; 41, en-US d2ureepe,
2009-07-17T09:14:21+02:00 - Seite 281
Version: 2.11.8.1Vehicle status messages in the multifunction display
281
Display messages DISTRONIC PLUS
- - - mph
HOLD
Off
Blind Spot Assist
Currently Unavailabl e See Operator's Manual
Blind Spot Assist Parking Guidance
Inoperativ
Inoperativ
Possible causes/consequences and M Solutions One of the activation conditions for the DISTRONIC PLUS has not been fulfilled. You may have attempted to set a speed below 20 mph (30 km/h). X Drive faster than 20 mph (30 km/h) if the situation allows
and set the speed.
X Check the activation conditions for the DISTRONIC PLUS
(Y page 153).
The HOLD function switched off because the vehicle was sliding, for example on a slippery surface. X Activate the HOLD function later. The Blind Spot Assist is deactivated because the area around the sensors in the front or the rear bumper is dirty. X Clean the front and rear bumper (Y page 263). The Blind Spot Assist is deactivated because the battery voltage is insufficient. X Have the battery checked at an authorized Mercedes-Benz
Center.
The Blind Spot Assist is switched off because the radar sensor system is temporarily inoperative due to electromagnetic interference near television and radio transmitter stations, toll stations, speed measuring systems, etc. X Wait until the message in the multifunction display
disappears.
The Blind Spot Assist is malfunctioning. X Contact an authorized Mercedes-Benz Center as soon as
possible.
The Parktronic system is malfunctioning. X Have the system checked at an authorized Mercedes-Benz
Center as soon as possible.
212_AKB; 2; 41, en-US d2ureepe,
2009-07-17T09:14:21+02:00 - Seite 282
Version: 2.11.8.1282 Vehicle status messages in the multifunction display
Display messages Parking Guidance
Canceled
Parking Guidance Radar Sensors
Finished
Deactivate d See Operator's Manual
Possible causes/consequences and M Solutions The Advanced Parking Guidance has been canceled because: Rthe vehicle is sliding Rthe bumper became dirty in the area of the sensors Rthere has been a malfunction X Use the Advanced Parking Guidance again later. If the parking space symbol is not shown in the multifunction display at a speed below 10 mph (16 km/h): X Clean the bumpers (Y page 263). or X Restart the engine. or X Contact an authorized Mercedes-Benz Center. Advanced Parking Guidance: The vehicle is in the end position. The display message disappears automatically. You have attempted to activate the DISTRONIC PLUS or the PRE-SAFE® Brake even though you have switched off the radar sensors on the vehicle. X Check if switching on the radar sensors is permitted
X Switch on the radar sensors using the instrument cluster
(Y page 144).
control system.
212_AKB; 2; 41, en-US d2ureepe,
2009-07-17T09:14:21+02:00 - Seite 283
Version: 2.11.8.1Vehicle status messages in the multifunction display
283
Display messages Lane Keeping Assist
Currently Unavailabl e See Operator's Manual
Possible causes/consequences and M Solutions The Lane Keeping Assist is temporarily unavailable. The Lane Keeping Assist is deactivated because: Rthe windshield in front of the camera is dirty Rits function is impaired as a result of heavy precipitation or
fog
Rlane markings are not present for an extended period of
time
Rlane markings are worn, dark, or covered by dirt or snow
for example
The Lane Keeping Assist becomes operational again and the message in the multifunction display disappears when: Rdirt on the windshield has fallen off while driving (e.g. slush
or snow)
Rthe system recognizes full camera availability X If necessary, clean the windshield in front of the camera
(Y page 264).
The Lane Keeping Assist is malfunctioning. X Contact an authorized Mercedes-Benz Center.
Inoperativ
Lane Keeping Assist
Vehicle
Display messages Apply Brake
to Shift from 'P'
Door Open
Vehicle Not in 'P' In addition an acoustic warning sounds.
Possible causes/consequences and M Solutions You have attempted to shift the automatic transmission into drive position D, reverse gear R or neutral position N without depressing the brake pedal. X Depress the brake pedal.
You have opened the driver’s door and the automatic transmission is still in drive position D, reverse gear R or neutral position N. X Before you leave the vehicle, make sure the automatic
transmission is in park position P and the parking brake is engaged.
212_AKB; 2; 41, en-US d2ureepe,
2009-07-17T09:14:21+02:00 - Seite 284
Version: 2.11.8.1284 Vehicle status messages in the multifunction display
Display messages Service Required
Do Not Shift Gears Visit Dealer
Only Shift to 'P' when Vehicle is Stationary Shift to 'P' or 'N'
to Start Engine
Auxiliary Battery
Malfunctio
Tires
Display messages Then Check Tire Restart Pressure Run Flat Indicator
Run Flat Indicator
Inoperativ
Possible causes/consequences and M Solutions In addition an acoustic warning sounds. The automatic transmission cannot be shifted out of the current transmission position because of a malfunction. If the automatic transmission is in drive position D: X Without shifting the automatic transmission out of drive position D, drive to an authorized Mercedes-Benz Center.
If the automatic transmission is set to position neutral position N, reverse gear R or park position P: X Do not drive. X Contact an authorized Mercedes-Benz Center or call
Roadside Assistance.
You have attempted to shift the automatic transmission into park position P although the vehicle was still in motion. X Stop your vehicle as soon as it is safe to do so. X Shift the automatic transmission to park position P.
You have attempted to start the engine with the KEYLESS-GO start/stop button while the automatic transmission was in reverse gear R or drive position D. X Shift the automatic transmission into park position P or
neutral position N. Make sure the brake pedal is depressed.
The backup battery for the automatic transmission is no longer charging. X Contact an authorized Mercedes-Benz Center.
Possible causes/consequences and M Solutions There has been a warning message about a loss in the tire inflation pressure and the tire pressure loss warning system was not restarted yet. X Make sure the correct tire inflation pressure is set for each
tire.
X Then restart the tire pressure loss warning system
(Y page 232).
The tire pressure loss warning system is malfunctioning. X Have the tire pressure loss warning system checked at an
authorized Mercedes-Benz Center.
212_AKB; 2; 41, en-US d2ureepe,
2009-07-17T09:14:21+02:00 - Seite 285
Version: 2.11.8.1Vehicle status messages in the multifunction display
285
Display messages Check Tire Pressure Soon
Possible causes/consequences and M Solutions The tire pressure loss warning system indicates that the tire inflation pressure is too low in at least one tire. X Carefully bring the vehicle to a halt, avoiding abrupt steering and braking maneuvers. Observe the traffic situation around you.
Tire pressures will be displayed Tire Press. Monitor Tire Pressure Monitor
after driving a few minutes Inoperativ
Inoperativ e No Wheel Sensors
TirePress. Sensor(s)M
issing
X Check the tires and, if necessary, change the wheel
X Check and adjust tire inflation pressure as required
(Y page 323).
(Y page 231).
X Restart the tire pressure loss warning system after
adjusting the tire inflation pressure values (Y page 232). The tire inflation pressure is being checked by the Advanced TPMS. X Drive the vehicle for a few minutes.
The Advanced TPMS is malfunctioning. X Have the Advanced TPMS checked at an authorized
Mercedes-Benz Center.
There are wheels without appropriate wheel sensors mounted (e.g. winter tires). X Have the Advanced TPMS checked at an authorized
Mercedes-Benz Center.
X Have the appropriate wheel sensors installed at an
authorized Mercedes-Benz Center.
At least one sensor is defect (e.g. battery is empty). The respective tire is indicated by – – instead of the tire inflation pressure in the multifunction display. X Have the Advanced TPMS checked at an authorized
Mercedes-Benz Center.
X Have the wheel sensors installed at an authorized
Mercedes-Benz Center.
At least one wheel without appropriate wheel sensors is mounted (e.g. spare wheel). The respective tire is indicated by – – instead of the tire inflation pressure in the multifunction display. X Have the Advanced TPMS checked at an authorized
Mercedes-Benz Center.
X Have the wheel sensors installed at an authorized
Mercedes-Benz Center.
212_AKB; 2; 41, en-US d2ureepe,
2009-07-17T09:14:21+02:00 - Seite 286
Version: 2.11.8.1286 Vehicle status messages in the multifunction display
Display messages Tire Press. Monitor
Currently Unavailabl
Correct Tire Pressure
Caution Tire Defect
Check Tires
Possible causes/consequences and M Solutions The Advanced TPMS cannot monitor the tire inflation pressure due to a nearby radio interference source or insufficient power supply. As soon as the causes of the malfunction have been rectified, the Advanced TPMS becomes active again automatically after a few minutes of driving. The tire inflation pressure is too low in at least one tire. or The tire inflation pressures of the individual tires differ from each other significantly. The tire inflation pressure values are shown in the multifunction display. X Check and correct tire inflation pressure as required
(Y page 231).
X Restart the Advanced TPMS (Y page 236). At least one tire is deflating. The respective tire is indicated in the multifunction display. X Carefully bring the vehicle to a halt, avoiding abrupt
steering and braking maneuvers.
X If necessary, change the wheel (Y page 323). The tire inflation pressure in at least one tire is significantly below the reference value. The respective tire is indicated in the multifunction display. X Carefully bring the vehicle to a halt, avoiding abrupt
steering and braking maneuvers.
X Check and adjust tire inflation pressure as required. X If necessary, change the wheel (Y page 323).
G Warning! Do not drive with a flat tire. A flat tire affects the ability to steer or brake the vehicle. You may lose control of the vehicle. Continued driving with a flat tire will cause excessive heat build-up and possibly a fire.
G Warning! Follow recommended tire inflation pressures. Do not underinflate tires. Underinflated tires wear excessively and/or unevenly, adversely affect handling and fuel economy, and are more likely to fail from being overheated.
212_AKB; 2; 41, en-US d2ureepe,
2009-07-17T09:14:21+02:00 - Seite 287
Version: 2.11.8.1Vehicle status messages in the multifunction display
287
Do not overinflate tires. Overinflated tires can adversely affect handling and ride comfort, wear unevenly, increase stopping distance, and result in sudden deflation (blowout) because they are more likely to become punctured or damaged by road debris, potholes etc.
Symbol messages Brake
Display messages # Check Brake Pad Wear
Possible causes/consequences and M Solutions The brake pads have reached their wear limit. X Have the brake pads replaced as soon as possible at an
authorized Mercedes-Benz Center.
! Brake pad thickness must be visually inspected by a qualified technician at the intervals
specified in the Maintenance Booklet.
212_AKB; 2; 41, en-US d2ureepe,
2009-07-17T09:14:21+02:00 - Seite 288
Version: 2.11.8.1288 Vehicle status messages in the multifunction display
Display messages ABS and ESC Inoperativ (USA only) e See Operator’s (Canada Manual only)
(USA only) (Canada only)
ABS and ESC Currently Unavailabl e See Operator’s Manual
Possible causes/consequences and M Solutions In addition, the yellow ESC warning lamp ä, the yellow ESC OFF warning lamp å, and the yellow ABS indicator lamp ! come on. The brake system is still functioning normally but due to a malfunction, the ABS, the BAS, the BAS PLUS, the ESC, the hill-start assist system, the HOLD function, the PRE-SAFE® system, and the PRE-SAFE® Brake are unavailable. The ATTENTION ASSIST is disabled. X Continue driving with added caution. Wheels may lock
during hard braking, reducing steering capability.
X Adjust driving to be consistent with reduced braking
responsiveness.
X Have the system checked at an authorized Mercedes-Benz
Center as soon as possible.
Failure to follow these instructions increases the risk of an accident. In addition, the yellow ESC warning lamp ä, the yellow ESC OFF warning lamp å, and the yellow ABS indicator lamp ! come on. The brake system still functions normally but due to insufficient power supply, the ABS, the BAS, the BAS PLUS, the ESC, the hill-start assist system, the HOLD function, the PRE-SAFE® system, and the PRE-SAFE® Brake are unavailable. The ATTENTION ASSIST is disabled. X Continue driving with added caution. Wheels may lock
during hard braking, reducing steering capability.
X Adjust driving to be consistent with reduced braking
responsiveness.
When the voltage is above the required value again, the ABS, the BAS, the BAS PLUS, the ESC, the hill-start assist system, the HOLD function, the PRE-SAFE® system, and the PRE-SAFE® Brake are operational again and the message should disappear. If the message does not disappear: X Have the alternator and the battery checked. Failure to follow these instructions increases the risk of an accident.
212_AKB; 2; 41, en-US d2ureepe,
2009-07-17T09:14:21+02:00 - Seite 289
Version: 2.11.8.1Vehicle status messages in the multifunction display
289
Display messages (USA only) (Canada only)
EBD, ABS, and ESC Inoperativ e See Operator's Manual
Release Parking Brake
Check Brake Fluid Level
(USA only) (Canada only) (USA only) (Canada only)
Possible causes/consequences and M Solutions In addition, the yellow ESC warning lamp ä, the yellow ESC OFF warning lamp å, and the yellow ABS indicator lamp ! come on. The brake system is still functioning normally but due to a malfunction, the ABS, the BAS, the BAS PLUS, the EBP, the ESC, the HOLD function, the PRE-SAFE® system, and the PRE- SAFE® Brake are unavailable. The ATTENTION ASSIST is disabled. X Continue driving with added caution. Wheels may lock
during hard braking, reducing steering capability.
X Adjust driving to be consistent with reduced braking
responsiveness.
X Have the system checked at an authorized Mercedes-Benz
Center as soon as possible.
Failure to follow these instructions increases the risk of an accident. You are driving with the parking brake engaged. In addition an acoustic warning sounds. X Release the parking brake.
There is insufficient brake fluid in the reservoir. Risk of accident! X Stop the vehicle in a safe location or as soon as it is safe
to do so.
X Engage the parking brake. X Do not drive any further. X Contact an authorized Mercedes-Benz Center or call
Roadside Assistance.
Do not add brake fluid! This will not solve the problem.
G Warning! Driving with the message Check Brake Fluid Level displayed can result in an accident. Have your brake system checked immediately. Do not add brake fluid before checking the brake system. Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching fire. You can be seriously burned.
! If you find that the brake fluid in the brake fluid reservoir has fallen to the minimum mark
or below, have the brake system checked for brake pad thickness and leaks.
212_AKB; 2; 41, en-US d2ureepe,
2009-07-17T09:14:21+02:00 - Seite 290
Version: 2.11.8.1290 Vehicle status messages in the multifunction display
Safety systems
Display messages ÷ ESC Inoperativ e See Operator's Manual
G Tele Aid Inoperativ
6 SRS
Malfunctio n Service Required 6 Front
Left SRS Malfunctio n Service Required 6 Front Right SRS Malfunctio n Service Required
Possible causes/consequences and M Solutions In addition, the yellow ESC warning lamp ä and the yellow ESC OFF warning lamp å come on. The brake system is still functioning normally but due to a malfunction, the BAS, the BAS PLUS, the ESC, the hill-start assist system, the HOLD function, the PRE-SAFE® system, and the PRE-SAFE® Brake are unavailable. The ATTENTION ASSIST is disabled. X Continue driving with added caution. Wheels may lock
during hard braking, reducing steering capability.
X Adjust driving to be consistent with reduced braking
responsiveness.
X Have the system checked at an authorized Mercedes-Benz
Center as soon as possible.
Failure to follow these instructions increases the risk of an accident. One or more main functions of the Tele Aid system are malfunctioning. X Have the Tele Aid system checked at an authorized
Mercedes-Benz Center.
There is a malfunction in the Supplemental Restraint System (SRS). The air bags or Emergency Tensioning Devices (ETDs) could deploy unexpectedly or fail to activate in an accident. X Drive with added caution to the nearest authorized
Mercedes-Benz Center.
Components of the driver’s supplemental restraint system may not work properly. X Drive with added caution to the nearest authorized
Mercedes-Benz Center.
Components of the front passenger’s supplemental restraint system may not work properly. X Drive with added caution to the nearest authorized
Mercedes-Benz Center.
212_AKB; 2; 41, en-US d2ureepe,
2009-07-17T09:14:21+02:00 - Seite 291
Version: 2.11.8.1Vehicle status messages in the multifunction display
291
Possible causes/consequences and M Solutions Components of the left rear passenger’s supplemental restraint system may not work properly. X Drive with added caution to the nearest authorized
Mercedes-Benz Center.
Components of the center rear passenger’s supplemental restraint system may not work properly. X Drive with added caution to the nearest authorized
Mercedes-Benz Center.
Components of the right rear passenger’s supplemental restraint system may not work properly. X Drive with added caution to the nearest authorized
Mercedes-Benz Center.
The left window curtain air bag may not work properly. X Drive with added caution to the nearest authorized
Mercedes-Benz Center.
The right window curtain air bag may not work properly. X Drive with added caution to the nearest authorized
Mercedes-Benz Center.
6 Rear
Display messages 6 Rear Left SRS Malfunctio n Service Required 6 Rear Center SRS Malfunctio n Service Required Right SRS Malfunctio n Service Required 6 Left Side Curtain Airbag Malfunctio n Service Required 6 Right Side Curtain Airbag Malfunctio n Service Required
G Warning! In the event a malfunction of the SRS is indicated as outlined above, the SRS may not be operational. For your safety, we strongly recommend that you contact an authorized Mercedes-Benz
Center immediately to have the system checked. Otherwise the SRS may not be activated when needed in an accident, which could result in serious or fatal injury, or it might deploy unexpectedly and unnecessarily which could also result in injury.
212_AKB; 2; 41, en-US d2ureepe,
2009-07-17T09:14:21+02:00 - Seite 292
Version: 2.11.8.1292 Vehicle status messages in the multifunction display
Driving systems
Display messages ¨ Vehicle Rising ¨ Vehicle
