Login- Download PDF Manual
-
approximately 5 minutes. The pressure gauge must display at least 26 psi (1.8 bar). G Warning! The air hose can become hot during inflation. Please exercise appropriate caution.
! Do not operate the electric air pump
longer than 8 minutes without interruption. Otherwise it may overheat.
212_AKB; 2; 41, en-US d2ureepe,
332 Flat tire
You may operate the air pump again after it has cooled off.
If the tire inflation pressure of at least 26 psi (1.8 bar) is not attained: X Turn off the electric air pump by pressing
0 on electric air pump switch =.
X Detach filler hose D from tire valve E. X Drive vehicle back or forth very slowly
approximately 30 ft (10 m). This serves to better distribute the TIREFIT sealant material inside the tire.
X Inflate the tire again. G Warning! If a tire inflation pressure of 26 psi (1.8 bar) is not attained, the tire is too severely damaged for TIREFIT to provide a reliable tire repair. In this case, TIREFIT cannot properly seal the tire. Do not drive the vehicle. Contact the nearest Mercedes-Benz Center or call Roadside Assistance.
After attaining a tire inflation pressure of at least 26 psi (1.8 bar): X Press 0 on electric air pump switch =.
The electric air pump is switched off.
X Detach the TIREFIT kit from the tire valve. G Warning! The air hose may still be hot. Exercise proper caution to avoid burning yourself when detaching the electric air pump.
! Remaining TIREFIT sealant could escape
from the filler hose after it has been detached from the tire valve. TIREFIT sealant may cause stains. Therefore, cover the filler hose, e.g. by inserting it into the plastic bag the TIREFIT kit was packed in.
X Drive off immediately.
2009-07-17T09:14:21+02:00 - Seite 332
Version: 2.11.8.1G Warning! Do not exceed a vehicle speed of 50 mph (80 km/h). A TIREFIT repair is not designed to operate at higher speeds. The sticker must be attached on the instrument cluster where it will be easily seen by the driver. Vehicle handling characteristics of a TIREFIT repaired tire may change. Adapt your driving accordingly.
X After driving the vehicle for an initial 10 minutes, check the tire inflation pressure using the pressure gauge. G Warning! If tire inflation pressure has fallen below 20 psi (1.3 bar) do not continue to drive the vehicle. Park your vehicle safely away from the roadway and contact the nearest authorized Mercedes-Benz Center or Roadside Assistance. Have the damaged tire replaced.
If the tire inflation pressure is at least 20 psi (1.3 bar), inflate or deflate the tire to the correct tire inflation pressure (see Tire and Loading Information placard on the driver’s door B-pillar):
Version 2
X To increase tire inflation pressure:Switch on the electric air pump.
X To decrease tire inflation pressure:
212_AKB; 2; 41, en-US d2ureepe,
2009-07-17T09:14:21+02:00 - Seite 333
Version: 2.11.8.1Version 1: Open vent screw F on pressure gauge G (Y page 331). Version 2: Press yellow deflate button a located in air pump housing next to pressure gauge G.
X Drive to the nearest qualified workshop,
e.g. an authorized Mercedes-Benz Center, to have the damaged tire replaced. X Recommended duration of use: A
maximum of 300 miles (500 km) at 50 mph (80 km/h) or below with the recommended tire inflation pressure.
X Contact an authorized Mercedes-Benz
Center as soon as possible to obtain a new TIREFIT kit.
X Bring used TIREFIT materials to an
authorized Mercedes-Benz Center for proper disposal.
X Replace your TIREFIT container every 4 years. Replacement containers are available at any authorized Mercedes-Benz Center.
Bleeding the fuel system (diesel engine only)
Driving the vehicle until the fuel tank is empty is not recommended. Otherwise, air may be sucked into the fuel system. If this happens, the malfunction indicator lamp ; comes on and the engine may not start immediately after refueling the vehicle. After refueling: X Make sure the automatic transmission is in
park position P. The transmission position indicator in the multifunction display should be on P. X Do not depress the accelerator. X If necessary, remove the KEYLESS-GO
start/stop button from the starter switch. X Turn the SmartKey in the starter switch to
position 2 for at least 10 seconds.
AdBlue® (diesel engine only)
333
X Return the SmartKey in the starter switch
to position 0.
X Turn the SmartKey in the starter switch to position 3 and hold it there for a maximum of 10 seconds or until the engine runs surge-free.
If the engine does not start: X Turn the SmartKey in the starter switch
once more to position 2 for at least 10 seconds.
X Return the SmartKey in the starter switch
to position 0.
X Turn the SmartKey in the starter switch once more to position 3 and hold it there for a maximum of 10 seconds or until the engine runs surge-free.
X If necessary, repeat the above steps. If the engine still does not start after 3 attempts: Do not make any further attempts to start the engine. Contact an authorized Mercedes- Benz Center or call Roadside Assistance (Y page 210). i When the malfunction indicator
lamp ; in the instrument cluster has been illuminated for the above condition, it will remain illuminated until the engine was cycled on and off four times in a row.
AdBlue® (diesel engine only)
The BlueTEC exhaust gas aftertreatment system requires a reducing agent (AdBlue®) in order to function properly. Refilling with AdBlue® is part of the regular maintenance service work. A tankful of AdBlue® should suffice until the next maintenance service under normal driving conditions. When the AdBlue® tank is low, the message Check Additive See Operator’s Manual appears in the multifunction display. When the AdBlue® level drops to the minimum level, the message Remaining
212_AKB; 2; 41, en-US d2ureepe,
2009-07-17T09:14:21+02:00 - Seite 334
Version: 2.11.8.1334 AdBlue® (diesel engine only) Starts: 20 appears in the multifunction display. i When the message Remaining Starts: 20 appears in the multifunction display, you can start the engine 20 more times. If you do not add AdBlue®, the engine cannot be started beyond that point. Fill the AdBlue® tank with approximately 1 gal (3.79 l) AdBlue® (corresponds to approximately 2 AdBlue® refill containers) or have the AdBlue® tank filled by an authorized Mercedes-Benz Center.
i For refilling outside the maintenance service intervals, refill the AdBlue® tank with approximately 1 gal (3.79 l) AdBlue® (corresponds to approximately 2 AdBlue® refill containers).
Always use the particular AdBlue® refill containers for refilling outside the maintenance service interval. Contact an authorized Mercedes-Benz Center or call Roadside Assistance if necessary (Y page 210). Additional information on BlueTEC exhaust gas aftertreatment and AdBlue® is available at any authorized Mercedes-Benz Center.
Refilling with AdBlue® G Warning! Make sure RAdBlue® does not come into contact with
skin, eyes, or clothing
Rto keep AdBlue® out of the reach of children
If you and/or others have come into contact with AdBlue®: RIf AdBlue® has gotten into contact with
eyes, flush with plenty of water immediately and seek medical help.
RClean affected skin immediately with plenty
of water.
RIf AdBlue® was swallowed, rinse mouth
immediately with plenty of water and drink plenty of water. Consult a physician. G Warning! When opening the filler cap of the AdBlue® tank ammonia gas vapors may escape. Refill AdBlue® in a well ventilated area only. Ammonia gas vapors have a pungent odor and are particularly irritating for your skin, mucous membranes, and eyes. Inhaling ammonia gas vapors will cause burning eyes, nose, and throat, as well as coughing and watering eyes.
! Only use AdBlue® complying with ISO 22241. Do not add additives to AdBlue® and do not dilute AdBlue® with water. Otherwise, the BlueTEC exhaust gas aftertreatment system could be damaged. Damage caused by using additives or diluting with water are not covered by the Mercedes-Benz Limited Warranty.
! Rinse surfaces that have come into
contact with AdBlue®, or remove AdBlue® with a moist cloth and cold water immediately. If AdBlue® has crystallized already, use cold water and a sponge. AdBlue® residues will crystallize and soil the affected surfaces.
! AdBlue® is not a fuel additive and must
not be added to the diesel fuel tank. If AdBlue® reaches the diesel fuel tank, the engine could be damaged which is not covered by the Mercedes-Benz Limited Warranty.
212_AKB; 2; 41, en-US d2ureepe,
2009-07-17T09:14:21+02:00 - Seite 335
Version: 2.11.8.1AdBlue® (diesel engine only)
335
For more information on AdBlue®, see (Y page 364). The AdBlue® filler neck is located in the space underneath the trunk floor. X Switch off the ignition. X Open the trunk (Y page 81). X Lift the trunk floor (Y page 268).
X Turn AdBlue® filler cap cover : counterclockwise and remove it.
X Turn AdBlue® filler cap ;
counterclockwise and open it. Filler cap ; is tethered with a plastic strap.
X Unscrew the dust cap from AdBlue® refill
container =.
X Place AdBlue® refill container = on the
filler neck as illustrated and tighten it moderately (hand-tight) by turning it clockwise.
! Make sure to tighten the AdBlue® refill container only moderately, i.e. hand-tight, as you could otherwise damage it.
X Push AdBlue® refill container = down.
The AdBlue® tank is filled. This may take up to 1 minute.
i When you stop pushing the AdBlue® refill
container down, the filling process is stopped and you can remove the refill container.
X Release AdBlue® refill container =. X Turn AdBlue® refill container = counterclockwise and remove it.
X Place AdBlue® filler cap ; on filler neck
and turn it clockwise.
212_AKB; 2; 41, en-US d2ureepe,
336 Battery
X Place AdBlue® filler cap cover : as
illustrated and turn it clockwise to its stop.
X Lower the trunk floor. X Close the trunk. X Drive the vehicle at a speed of at least 10 mph (16 km/h). The message Check Additive See Operator’s Manual disappears after approximately 1 minute. i If the message Check Additive See Operator’s Manual still appears in the multifunction display, refill with one more container of AdBlue®.
i Have the AdBlue® level checked and, if necessary, filled completely afterward at an authorized Mercedes-Benz Center.
Battery Safety notes A battery should always be sufficiently charged in order to achieve its rated service life. Refer to Maintenance Booklet for battery maintenance intervals. If you use your vehicle mostly for short- distance trips, you will need to have the battery charge checked more frequently. When replacing a battery, always use a battery approved by Mercedes-Benz. If you do not intend to operate your vehicle for an extended period of time, contact an authorized Mercedes-Benz Center about steps you need to observe. G Warning! Observe all safety instructions and precautions when handling automotive batteries.
2009-07-17T09:14:21+02:00 - Seite 336
Version: 2.11.8.1Risk of explosion.
Fire, open flames and smoking are prohibited when handling batteries. Avoid creating sparks. Battery acid is caustic. Do not allow it to come into contact with skin, eyes or clothing. Wear suitable protective clothing, especially gloves, apron and faceguard. Wear eye protection. Rinse any acid spills immediately with clear water. Contact a physician if necessary. Keep children away.
Follow the instructions in this Operator’s Manual.
A battery contains materials that can harm the environment if disposed of improperly. A large 12 V storage battery contains lead. Recycling of the battery is the preferred method of disposal. Many states (USA only) or provinces (Canada only) require sellers of batteries to accept the old battery for recycling. G Warning! Failure to follow these instructions can result in severe injury or death. Never lean over batteries while connecting. You might get injured. Battery fluid contains sulfuric acid. Do not allow this fluid to come in contact with eyes, skin or clothing. In case it does, immediately
212_AKB; 2; 41, en-US d2ureepe,
2009-07-17T09:14:21+02:00 - Seite 337
Version: 2.11.8.1flush affected area with water and seek medical help if necessary. A battery will also produce hydrogen gas, which is flammable and explosive. Keep flames or sparks away from battery, avoid improper connection of jumper cables, smoking etc. G Warning! Do not place metal objects on the battery as this could result in a short circuit. Use leak-proof batteries only to avoid the risk of acid burns in the event of an accident. Take care that you do not become statically charged, e.g. by wearing synthetic clothing or rubbing against textiles. For this reason, you also should not pull or push the battery over carpets or other synthetic materials. Never touch the battery first. First touch the outside body of the vehicle in order to release any possible electrostatic charges. Do not rub the battery with rags or cloths. The battery could explode if touched due to electrostatic charge or due to spark formation.
! The battery is a Valve-Regulated Lead Acid (VRLA) battery, also referred to as “fleece” battery. Such batteries do not require topping-up of the electrolyte level. VRLA batteries therefore do not have cell caps and the battery cover is non-removable. Do not attempt to open the battery as otherwise the battery will be damaged. VRLA batteries do not require topping-up of the electrolyte level. They cannot be opened to check the electrolyte level. However, the battery condition must be checked periodically by performing a battery conductance test. Refer to Maintenance Booklet for battery condition testing intervals.
Battery
337
The factory-equipped battery may only be replaced with a battery that Rhas the same security features Ris of identical size Ris of identical voltage Ris of identical capacity
! As any other battery, the battery may
discharge if you do not operate the vehicle for an extended period of time. Have the battery disconnected at a qualified workshop or an authorized Mercedes-Benz Center in such a case. You may also connect an accessory battery charge unit expressly approved by Mercedes-Benz for your vehicle model to maintain the battery charge. Contact an authorized Mercedes- Benz Center for further information. The battery, the battery ventilation hose and the lateral plug must always be securely installed when the vehicle is in operation.
! Never loosen or detach battery terminal clamps while the engine is running or the SmartKey is in the starter switch or KEYLESS-GO button is in position 1. Otherwise the alternator and other electronic components could be severely damaged. Have the battery checked regularly at an authorized Mercedes-Benz Center. Refer to Maintenance Booklet for maintenance intervals or contact an authorized Mercedes-Benz Center for further information.
Charging the battery G Warning! Never charge a battery while still installed in the vehicle unless the accessory battery charge unit approved by Mercedes-Benz is being used. Gases may escape during
2009-07-17T09:14:21+02:00 - Seite 338
Version: 2.11.8.1improper connection of jumper cables, smoking, etc. Attempting to jump start a frozen battery can result in it exploding, causing personal injury. Read all instructions before proceeding.
! Do not tow-start the vehicle. You could
otherwise seriously damage the automatic transmission which is not covered by the Mercedes-Benz Limited Warranty.
! Jump starting should only be performed using the jump-start terminals located in the engine compartment. Avoid repeated and lengthy starting attempts. Do not attempt to start the engine using a battery quick-charge unit. If the engine does not run after several unsuccessful starting attempts, have it checked at the nearest authorized Mercedes-Benz Center. Excessive unburned fuel generated by repeated failed starting attempts may damage the catalytic converter21 and may present a fire risk. Make sure the jumper cables do not have loose or missing insulation. Make sure the cable clamps do not touch any other metal part while the other end is still attached to a battery.
If the battery is discharged, the engine can be started with jumper cables and the fully charged battery of another vehicle or an equivalent starter pack. Observe the following: RAccess to the battery is not possible on all vehicles. If you cannot access the battery of the other vehicle, provide jump start
212_AKB; 2; 41, en-US d2ureepe,
338
Jump starting
charging and could cause an explosion that may result in personal injury, paint damage or corrosion. An accessory battery charge unit specially adapted for Mercedes-Benz vehicles and tested and approved by Mercedes-Benz is available. It permits the charging of the battery in its installed position. Contact an authorized Mercedes-Benz Center for information and availability. Charge battery in accordance with the separate instructions for the accessory battery charger. Have the battery charged at an authorized Mercedes-Benz Center. If you charge the battery yourself, follow the operating instructions for your charging device. Only use a battery charge unit with a maximum charging voltage of 14.8 V. X Charge battery in accordance with the
instructions of the battery charger manufacturer.
Jump starting
G Warning! Failure to follow these directions will cause damage to the electronic components, and can lead to a battery explosion and severe injury or death. Never lean over batteries while connecting or jump starting. You might get injured. Battery fluid contains sulfuric acid. Do not allow this fluid to come in contact with eyes, skin or clothing. In case it does, immediately flush affected area with water, and seek medical help if necessary. A battery will also produce hydrogen gas, which is flammable and explosive. Keep flames or sparks away from battery, avoid
21 Vehicles with gasoline engine only.
212_AKB; 2; 41, en-US d2ureepe,
2009-07-17T09:14:21+02:00 - Seite 339
Version: 2.11.8.1Jump starting 339
power by an external battery or starter pack.
RJump starting should only be performed
when the engine and catalytic converter22
are cold.RDo not jump start the engine or charge the
battery if the battery is frozen. Let the battery thaw out first.
ROnly jump start from batteries with the
same voltage rating (12 V). Jump starting with a more powerful battery could damage the vehicle’s electrical system. Such damage will not be covered by the Mercedes-Benz Limited Warranty.
ROnly use jumper cables with sufficient
cross-section and insulated terminal clamps.
RAlways make sure the jumper cables are not on or near pulleys, fans or other parts that move when an engine is started or running.
RShould the battery be drained completely, let the donating power source charge the vehicle for several minutes before reattempting the starting process.
The jump-start contacts are located in the engine compartment on the passenger side. X Make sure the two vehicles do not touch. X Switch off all electrical consumers. X Engage the parking brake. X Make sure the automatic transmission is in
park position P.
X Open the hood (Y page 223).
Position B represents the charged battery of another vehicle or an equivalent starter pack. X Slide cover : from positive terminal = in
direction of arrow.
! Never invert the terminal connections!
22 Vehicles with gasoline engine only.
X Connect positive terminal ; of charged
battery B with positive terminal = with a jumper cable. Clamp the cable to positive terminal ; of charged battery B first. X Start engine of the vehicle with charged
battery B and run at idle speed.
212_AKB; 2; 41, en-US d2ureepe,
2009-07-17T09:14:21+02:00 - Seite 340
Version: 2.11.8.1340 Towing the vehicle
X Connect negative terminal ? of charged battery B with negative terminal A with a jumper cable. Clamp the cable to negative terminal ? of charged battery B first.
X Start engine of the vehicle with the
discharged battery and run at idle speed. You can now turn on the electrical consumers. Do not switch on the headlamps under any circumstances.
X Remove the jumper cables from negative
terminals ? and A first.
X Remove the jumper cables from positive
terminals ; and =. You can now switch on the headlamps. X Slide cover : from positive terminal =
back.
X Have the battery checked at the nearest
authorized Mercedes-Benz Center.
Towing the vehicle Safety notes G Warning! The vehicle is braked when the HOLD function or DISTRONIC PLUS is activated. Therefore, deactivate the HOLD function or DISTRONIC PLUS if the vehicle is to be towed. Mercedes-Benz recommends that the vehicle be transported with all wheels off the ground using flatbed or appropriate wheel lift/dolly equipment. This method is preferable to other types of towing. ! To prevent damage during transport, do
not tie down vehicle by its chassis or suspension parts.
If circumstances do not permit the recommended towing methods, the vehicle may be towed with all wheels on the ground or front axle raised (except vehicles with 4MATIC) only so far as necessary to have the vehicle moved to a safe location where the
recommended towing methods can be employed. ! Before towing the vehicle observe the
following instructions: RDo not tow-start the vehicle. You could
otherwise seriously damage the automatic transmission which is not covered by the Mercedes-Benz Limited Warranty.
RDo not tow with sling-type equipment. Towing with sling-type equipment over bumpy roads will damage radiator and supports.
RTowing of the vehicle should only be
done using the properly installed towing eye bolt. Never attach a tow cable, tow rope or tow rod to the vehicle chassis, frame or suspension parts.
G Warning! With the engine not running, there is no power assistance for the brake and steering systems. In this case, it is important to keep in mind that a considerably higher degree of effort is necessary to brake and steer the vehicle. Adapt your driving accordingly.
! Avoid pulling the vehicle abruptly or
diagonally, since it could result in damage to the chassis alignment.
! Do not use the towing eye bolt for
recovery, as this could damage the vehicle. If in doubt, recover the vehicle with a crane.
i If the battery is disconnected or
discharged Rthe SmartKey will not turn in the starter
switch
Rthe automatic transmission will remain in
park position P
For more information see “Battery” (Y page 336) or “Jump starting” (Y page 338).
212_AKB; 2; 41, en-US d2ureepe,
2009-07-17T09:14:21+02:00 - Seite 341
Version: 2.11.8.1Towing the vehicle 341
Installing towing eye bolt Depending on whether you are towing a vehicle or you are being towed, the towing eye bolt can be screwed into threaded holes which are located behind covers on each bumper. The towing eye bolt is supplied with the vehicle tool kit, located underneath the trunk floor (Y page 268). X Take the vehicle tool kit out of the trunk.
Removing cover in front bumper
X Press mark on cover : as indicated by the
arrow.
X Lift cover : off to reveal the threaded hole
for the towing eye bolt.
Removing cover in rear bumper G Warning! In order to avoid possible serious burns or injury, use extreme caution when removing the rear cover, because the rear exhaust pipe is extremely hot.
X Press mark on cover : as indicated by the
arrow.
X Lift cover : off to reveal the threaded hole
for the towing eye bolt.
Fixing towing eye bolt
Example illustration front bumper X Take the towing eye bolt and, if so
equipped, the wheel wrench from the vehicle tool kit (Y page 268).
X Screw towing eye bolt ; clockwise into
threaded hole to its stop.
X Insert wheel wrench into towing eye and tighten towing eye bolt ; by turning it clockwise.
or X If your vehicle is not equipped with a wheel
wrench, use a suitable object to turn the towing eye bolt.
212_AKB; 2; 41, en-US d2ureepe,
2009-07-17T09:14:21+02:00 - Seite 342
Version: 2.11.8.1342 Towing the vehicle
Removing towing eye bolt X Loosen towing eye bolt ; by turning it
counterclockwise.
X Unscrew towing eye bolt ;. X Reinstalling cover: Fit cover :
(Y page 341) and snap it into place.
X Store the towing eye bolt ; and wheel
wrench back into the vehicle tool kit.
Towing with one axle raised ! The vehicle may be towed only for
distances up to 30 miles (50 km) and at a speed not to exceed 30 mph (50 km/h).
! Vehicles with 4MATIC: Do not tow with
one axle raised. Doing so could damage the transfer case, which is not covered by the Mercedes-Benz Limited Warranty. All wheels must be on or off the ground. Observe instructions for towing the vehicle with all wheels on the ground.
X Make sure the ignition is switched on. X With the vehicle at a standstill, depress the
brake pedal and keep it pressed.
X Release the brake pedal. X If engaged, release the parking brake. X Switch off the automatic central locking
(Y page 144).
X Switch off the ignition and leave the
SmartKey in the starter switch.
X Switch on the hazard warning flasher
(Y page 101).
! Because the ESC operates automatically,
the engine and ignition must be shut off (SmartKey in starter switch position 0 or 1 or KEYLESS-GO start/stop button in position 0 or 1) when the vehicle is being towed with one axle raised. Active braking action through the ESC may otherwise seriously damage the brake system which is not covered by the Mercedes-Benz Limited Warranty.
Towing with all wheels on the ground G Warning! If circumstances require towing the vehicle with all wheels on the ground, always tow with a tow bar if: Rthe engine will not run Rthere is a malfunction in the brake system Rthere is a malfunction in the power supply
or in the vehicle’s electrical system
This is necessary to adequately control the towed vehicle. Prior to towing the vehicle with all wheels on the ground, make sure the SmartKey is in starter switch position 2. If the SmartKey is left in the starter switch position 0 for an extended period of time, it can no longer be turned in the switch. In this case, the steering is locked. To unlock, remove SmartKey from starter switch and reinsert. G Warning! With the engine not running, there is no power assistance for the brake and steering systems. In this case, it is important to keep in mind that a considerably higher degree of effort is necessary to brake and steer the vehicle. Adapt your driving accordingly.
X Make sure the ignition is switched on. X With the vehicle at a standstill, depress the
brake pedal and keep it pressed.
X Shift the automatic transmission into
neutral position N.
X Release the brake pedal. X If engaged, release the parking brake. X Switch on the hazard warning flasher
(Y page 101).
! The vehicle may be towed only for
distances up to 30 miles (50 km) and at a speed not to exceed 30 mph (50 km/h).
212_AKB; 2; 41, en-US d2ureepe,
2009-07-17T09:14:21+02:00 - Seite 343
Version: 2.11.8.1Fuses
343
i While being towed with the hazard
warning flasher in use, use the combination switch in the usual manner to signal turns. Only the selected turn signal will operate. Upon canceling the turn signal, the hazard warning flasher will operate again.
Fuses Introduction The electrical fuses in your vehicle serve to switch off malfunctioning power circuits. If a fuse is blown, the components and systems secured by that fuse will stop operating. G Warning! Only use fuses approved by Mercedes-Benz with the specified amperage for the system in question and do not attempt to repair or bridge a blown fuse. Using other than approved fuses or using repaired or bridged fuses may cause an overload leading to a fire, and/or cause damage to electrical components and/or systems. Have the cause determined and remedied by an authorized Mercedes-Benz Center. A blown fuse must be replaced by an appropriate spare fuse (recognizable by its color or the fuse rating given on the fuse) of the amperage recommended in the fuse chart. Any Mercedes-Benz Center will be glad to advise you on this subject. i In case of a blown fuse contact Roadside
Assistance or an authorized Mercedes- Benz Center.
If a newly inserted fuse blows again, have the cause determined and rectified by an authorized Mercedes-Benz Center. The fuse chart is located in the trunk with the vehicle tool kit (Y page 268). The fuse chart explains the fuse allocation and fuse amperages.
Before replacing fuses X Engage the parking brake. X Make sure the automatic transmission is in
park position P. The transmission position indicator in the multifunction display should be on P. X Switch off all electrical consumers. X Turn off the engine. X Remove the SmartKey from the starter
switch.
X Vehicles with KEYLESS-GO: Open the
driver’s door (this puts the starter switch in position 0, same as with the SmartKey removed from the starter switch). The driver’s door then can be closed again.
Fuse box in trunk
X Open the trunk. X Opening: Insert flat, blunt object as a lever
into the upper edge of cover : and pull cover : downward in direction of arrow.
X Closing: Install cover :.
Fuse box in engine compartment X Open the hood.
212_AKB; 2; 41, en-US d2ureepe,
344 Fuses
2009-07-17T09:14:21+02:00 - Seite 344
Version: 2.11.8.1X With a dry cloth, remove any moisture from
fuse box cover.
X Opening: Release wire ; from fuse box
cover.
X Move aside wire ;. Route wire ; behind
connection = to do this.
X Release clamps :. X Closing: Make sure the sealing rubber is
positioned properly.
X Press fuse box cover down and secure with
clamps :.
X Fasten wire ; on fuse box cover. ! The fuse box cover must be properly
positioned as described. Otherwise, moisture or dirt could enter the fuse box and possibly impair fuse operation.
X Close the hood after checking or replacing
fuses.
212_AKB; 2; 41, en-US d2ureepe,
2009-07-17T09:14:21+02:00 - Seite 345
Version: 2.11.8.1Vehicle equipment ............................ 346
Parts service ..................................... 346
Warranty coverage ........................... 346
Identification labels .......................... 346
Vehicle specification E 350
(212.056) ........................................... 348
Vehicle specification E 350 Blue- TEC (212.024) ................................... 348
Vehicle specification E 350
4MATIC (212.087) ............................. 349
Vehicle specification E 550
(212.072) ........................................... 350
Vehicle specification E 550
4MATIC (212.090) ............................. 351
Vehicle specification E 63 AMG (212.077) ........................................... 352
Rims and tires ................................... 353
Fuels, coolants, lubricants, etc. ...... 359345
212_AKB; 2; 41, en-US d2ureepe,
2009-07-17T09:14:21+02:00 - Seite 346
Version: 2.11.8.1RNew Vehicle Limited Warranty REmission System Warranty REmission Performance Warranty RCalifornia, Connecticut, Maine,
Massachusetts, New York, Pennsylvania, Rhode Island, and Vermont Emission Control Systems Warranty
RState Warranty Enforcement Laws (Lemon
Laws)
Replacement parts and accessories are covered by the Mercedes-Benz Parts and Accessories warranties, copies of which are available at any authorized Mercedes-Benz Center.
Loss of Service and Warranty Information booklet Should you lose your Service and Warranty Information booklet, have an authorized Mercedes-Benz Center arrange for a replacement. It will be mailed to you.
Identification labels
346
Identification labels
Vehicle equipment
i This Operator’s Manual describes all
features, standard or optional, potentially available for your vehicle at the time of purchase. Please be aware that your vehicle might not be equipped with all features described in this manual.
Parts service
All authorized Mercedes-Benz Centers maintain a stock of Genuine Mercedes-Benz Parts required for maintenance and repair work. In addition, strategically located parts distribution centers provide quick and reliable parts service. More than 300 000 different parts for Mercedes-Benz models are available. Genuine Mercedes-Benz Parts are subjected to stringent quality inspections. Each part has been specifically developed, manufactured or selected for and adapted to Mercedes-Benz vehicles. Therefore, Genuine Mercedes-Benz Parts should be installed. ! Do not use non-genuine Mercedes-Benz parts and accessories not authorized by Mercedes-Benz. Doing so could damage the vehicle, which is not covered by the Mercedes-Benz Limited Warranty. Also, it could compromise the vehicle’s durability or safety.
Warranty coverage
Your vehicle is covered under the terms of the warranties printed in the Service and Warranty Information booklet. Your authorized Mercedes-Benz Center will exchange or repair any defective parts originally installed in the vehicle in accordance with the terms of the following warranties:
The Vehicle Identification Number (VIN) can be found Ron certification label : on the driver’s door
B-pillar
Rembossed underneath the carpet in the
front passenger footwell
Ron the lower edge of the windshield
212_AKB; 2; 41, en-US d2ureepe,
2009-07-17T09:14:21+02:00 - Seite 347
Version: 2.11.8.1Identification labels
347
Example certification label (U.S. vehicles) ; VIN = Paintwork code
X Move the front passenger seat backward
as far as possible (Y page 88).
X Fold carpet ? backward.
VIN A is now visible.
Example certification label (Canada vehicles) ; VIN = Paintwork code
i Data shown on certification label are for illustration purposes only. These data are specific to each vehicle and may vary from data shown in the illustration. Refer to certification label on vehicle for actual data specific to your vehicle.
B Emission control information label, includes both federal and California certification exhaust emission standards
C VIN (on lower edge of windshield) D Engine number (engraved on engine)
i When ordering parts, please specify
vehicle identification and engine number.
212_AKB; 2; 41, en-US d2ureepe,
2009-07-17T09:14:21+02:00 - Seite 348
Version: 2.11.8.1348 Vehicle specification E 350 BlueTEC (212.024)
Vehicle specification E 350 (212.056)
Electrical system E 350
The quoted data apply only to the standard vehicle. Contact an authorized Mercedes- Benz Center for the corresponding data of all special bodies and special equipment.
Engine E 350
Engine, type Mode of operation
No. of cylinders Bore Stroke Total piston displacement Compression ratio Output acc. to SAE J 134923
Maximum torque acc. to SAE J 1349272
4-stroke engine, gasoline injection
3.66 in (92.90 mm) 3.39 in (86.00 mm)
213.5 cu in (3 498 cm3)
10.7:1
268 hp/6 000 rpm (200 kW/6 000 rpm)
258 lb-ft/
2 400 - 5 000 rpm
(350 Nm/
2 400 - 5 000 rpm)
Maximum engine speed Firing order Poly-V-belt
6 500 rpm
1-4-3-6-2-5
2 392 mmElectrical system E 350
Alternator Starter motor Battery Spark plugs, type
14 V/180 A 12 V/1.4 kW 12 V/70 Ah
Bosch Y 7 MPP33
Spark plugs, electrode gap Spark plugs, tightening torque
0.031 in (0.8 mm)
15 - 18 lb-ft (20 - 25 Nm)
Main dimensions E 350
57.8 in (1 467 mm)
81.5 in (2 071 mm)
191.9 in (4 874 mm)
Overall vehicle length Overall vehicle width24
Overall vehicle height Wheelbase Track, front Track, rear Ground clearance 4.1 in (104 mm) Turning circle 36.9 ft (11.3 m)113.1 in (2 874 mm) 62.2 in (1 580 mm) 63.0 in (1 599 mm)
Weights E 350
Roof load Trunk load
max. 220 lb (100 kg) max. 220 lb (100 kg)
Vehicle specification E 350 BlueTEC (212.024)
The quoted data apply only to the standard vehicle. Contact an authorized Mercedes- Benz Center for the corresponding data of all special bodies and special equipment.
23 Premium fuel required. Performance may vary with fuel octane rating. 24 Exterior rear view mirrors folded out.
212_AKB; 2; 41, en-US d2ureepe,
2009-07-17T09:14:21+02:00 - Seite 349
Version: 2.11.8.1Vehicle specification E 350 4MATIC (212.087)
349
Engine E 350 BlueTEC 642
Engine, type Mode of operation
No. of cylinders Bore Stroke Total piston displacement Compression ratio Output acc. to SAE J 1349
Maximum torque acc. to SAE J 1349Diesel 4-stroke
engine
3.27 in (83.00 mm) 3.62 in (92.00 mm)
182.3 cu in (2 987 cm3)
16.5:1
210 hp/3 400 rpm (157 kW/3 400 rpm)
400 lb-ft/
1 600 - 2 400 rpm
(543 Nm/
1 600 - 2 400 rpm)
Maximum engine speed Firing order Poly-V-belt
4 500 rpm
1-4-2-5-3-6
2 035 mmElectrical system E 350 BlueTEC 14 V/180 A 12 V/2.0 kW 12 V/95 Ah
Alternator Starter motor Battery
Main dimensions E 350 BlueTEC
Overall vehicle length Overall vehicle width25
191.9 in (4 874 mm)
81.5 in (2 071 mm)
Main dimensions E 350 BlueTEC
Overall vehicle height26
Wheelbase Track, front Track, rear Ground clearance26
Turning circle57.8 in (1 467 mm)
113.1 in (2 874 mm) 62.2 in (1 580 mm) 63.0 in (1 599 mm) 3.5 in (89 mm)
36.9 ft (11.3 m)
Weights E 350 BlueTEC
Roof load Trunk load
max. 220 lb (100 kg) max. 220 lb (100 kg)
Vehicle specification E 350 4MATIC (212.087)
The quoted data apply only to the standard vehicle. Contact an authorized Mercedes- Benz Center for the corresponding data of all special bodies and special equipment.
Engine E 350 4MATIC 272
Engine, type Mode of operation
4-stroke engine, gasoline injection
3.66 in (92.90 mm) 3.39 in (86.00 mm)
213.5 cu in (3 498 cm3)
10.7:1
No. of cylinders Bore Stroke Total piston displacement Compression ratio
25 Exterior rear view mirrors folded out. 26 Data apply to unladen vehicle with standard equipment. Data may vary in vehicles equipped with AIRMATIC
depending on the selected damping settings and the current vehicle level.
212_AKB; 2; 41, en-US d2ureepe,
2009-07-17T09:14:21+02:00 - Seite 350
Version: 2.11.8.1350 Vehicle specification E 550 (212.072)
Engine E 350 4MATIC
Output acc. to SAE J 134927
Maximum torque acc. to SAE J 1349268 hp/6 000 rpm (200 kW/6 000 rpm)
258 lb-ft/
2 400 - 5 000 rpm
(350 Nm/
2 400 - 5 000 rpm)
Maximum engine speed Firing order Poly-V-belt
6 500 rpm
1-4-3-6-2-5
2 392 mmElectrical system E 350 4MATIC 14 V/180 A 12 V/1.4 kW 12 V/70 Ah
Alternator Starter motor Battery Spark plugs, type Spark plugs, electrode gap Spark plugs, tightening torque
Bosch Y 7 MPP33
0.031 in (0.8 mm)15 - 18 lb-ft (20 - 25 Nm)
Main dimensions E 350 4MATIC
Overall vehicle length Overall vehicle width28
Overall vehicle height Wheelbase Track, front Track, rear191.9 in (4 874 mm)
81.5 in (2 071 mm)
57.8 in (1 467 mm)
113.1 in (2 874 mm) 62.2 in (1 580 mm) 63.0 in (1 599 mm)
Main dimensions E 350 4MATIC Ground clearance 4.1 in (104 mm) Turning circle 36.9 ft (11.3 m)
Weights E 350 4MATIC
Roof load Trunk load
max. 220 lb (100 kg) max. 220 lb (100 kg)
Vehicle specification E 550 (212.072)
The quoted data apply only to the standard vehicle. Contact an authorized Mercedes- Benz Center for the corresponding data of all special bodies and special equipment.
Engine E 550
Engine, type Mode of operation
No. of cylinders Bore Stroke Total piston displacement Compression ratio Output acc. to SAE J 134929
Maximum torque acc. to SAE J 1349273
4-stroke engine, gasoline injection
3.86 in (98.00 mm) 3.56 in (90.50 mm)
333.2 cu in (5 461 cm3)
10.7:1
382 hp/6 000 rpm (285 kW/6 000 rpm)
391 lb-ft/
2 800 - 4 800 rpm
(530 Nm/
2 800 - 4 800 rpm)
Maximum engine speed
6 500 rpm
27 Premium fuel required. Performance may vary with fuel octane rating. 28 Exterior rear view mirrors folded out. 29 Premium fuel required. Performance may vary with fuel octane rating.
212_AKB; 2; 41, en-US d2ureepe,
2009-07-17T09:14:21+02:00 - Seite 351
Version: 2.11.8.1Vehicle specification E 550 4MATIC (212.090)
351
Engine E 550
Firing order Poly-V-belt
1-5-4-2-6-3-7-8
2 392 mm
Electrical system E 550
Alternator Starter motor Battery Spark plugs, type Spark plugs, electrode gap Spark plugs, tightening torque
14 V/180 A 12 V/1.4 kW 12 V/95 Ah NGK PLKR 7A
0.031 in (0.8 mm)
15 - 18 lb-ft (20 - 25 Nm)
Main dimensions E 550
57.0 in (1 447 mm)
81.5 in (2 071 mm)
191.9 in (4 874 mm)
Overall vehicle length Overall vehicle width30
Overall vehicle height Wheelbase Track, front Track, rear Ground clearance 5.4 in (137 mm) Turning circle 36.9 ft (11.3 m)113.1 in (2 874 mm) 62.5 in (1 587 mm) 63.0 in (1 599 mm)
Weights E 550
Roof load Trunk load
max. 220 lb (100 kg) max. 220 lb (100 kg)
Vehicle specification E 550 4MATIC (212.090)
The quoted data apply only to the standard vehicle. Contact an authorized Mercedes- Benz Center for the corresponding data of all special bodies and special equipment.
Engine E 550 4MATIC 273
Engine, type Mode of operation
No. of cylinders Bore Stroke Total piston displacement Compression ratio Output acc. to SAE J 134931
Maximum torque acc. to SAE J 13494-stroke engine, gasoline injection
3.86 in (98.00 mm) 3.56 in (90.50 mm)
333.2 cu in (5 461 cm3)
10.7:1
382 hp/6 000 rpm (285 kW/6 000 rpm)
391 lb-ft/
2 800 - 4 800 rpm
(530 Nm/
2 800 - 4 800 rpm)
Maximum engine speed Firing order Poly-V-belt
6 500 rpm
1-5-4-2-6-3-7-8
2 392 mm
Electrical system E 550 4MATIC 14 V/180 A 12 V/1.4 kW 12 V/95 Ah NGK PLKR 7A
Alternator Starter motor Battery Spark plugs, type
30 Exterior rear view mirrors folded out. 31 Premium fuel required. Performance may vary with fuel octane rating.
212_AKB; 2; 41, en-US d2ureepe,
2009-07-17T09:14:21+02:00 - Seite 352
Version: 2.11.8.1352 Vehicle specification E 63 AMG (212.077)
Electrical system E 550 4MATIC
Engine E 63 AMG
Spark plugs, electrode gap Spark plugs, tightening torque
0.031 in (0.8 mm)
15 - 18 lb-ft (20 - 25 Nm)
Main dimensions E 550 4MATIC
57.0 in (1 447 mm)
81.5 in (2 071 mm)
191.9 in (4 874 mm)
Overall vehicle length Overall vehicle width32
Overall vehicle height Wheelbase Track, front Track, rear Ground clearance 5.4 in (137 mm) Turning circle 36.9 ft (11.3 m)113.1 in (2 874 mm) 62.2 in (1 580 mm) 63.0 in (1 599 mm)
Weights E 550 4MATIC
Roof load Trunk load
max. 220 lb (100 kg) max. 220 lb (100 kg)
Vehicle specification E 63 AMG (212.077)
The quoted data apply only to the standard vehicle. Contact an authorized Mercedes- Benz Center for the corresponding data of all special bodies and special equipment.
Engine, type Mode of operation
No. of cylinders Bore Stroke Total piston displacement Compression ratio Output acc. to SAE J 134933
Maximum torque acc. to SAE J 1349
Maximum engine speed Firing order Poly-V-belt156
4-stroke engine, gasoline injection
4.02 in (102.20 mm) 3.72 in (94.60 mm)
378.8 cu in (6 208 cm3)
11.3:1
518 hp/6 800 rpm (386 kW/6 800 rpm) 465 lb-ft/5 200 rpm (630 Nm/5 200 rpm)
7 200 rpm
1-5-4-2-6-3-7-8
2 360 mm
Electrical system E 63 AMG
Alternator Starter motor Battery Spark plugs, type Spark plugs, electrode gap Spark plugs, tightening torque
14 V/180 A 12 V/1.7 kW 12 V/80 Ah
NGK ILZKAR 7A10
0.039 in (1.0 mm)15 - 18 lb-ft (20 - 25 Nm)
32 Exterior rear view mirrors folded out. 33 Premium fuel required. Performance may vary with fuel octane rating.
212_AKB; 2; 41, en-US d2ureepe,
2009-07-17T09:14:21+02:00 - Seite 353
Version: 2.11.8.1Rims and tires
353
Main dimensions E 63 AMG
81.5 in (2 071 mm)
56.8 in (1 442 mm)
192.6 in (4 891 mm)
Overall vehicle length Overall vehicle width34
Overall vehicle height Wheelbase Track, front Track, rear Ground clearance 4.5 in (114 mm) Turning circle 37.1 ft (11.30 m)113.1 in (2 874 mm) 64.0 in (1 625 mm) 62.8 in (1 594 mm)
E 63 AMG
Roof load Trunk load
max. 220 lb (100 kg) max. 220 lb (100 kg)
34 Exterior rear view mirrors folded out.
Rims and tires Notes ! Only use tires which have been tested and
