2012 Mercedes-benz CL Class Owners Manual

X Attach trunk floor cover = to the upper

edge of the trunk with hooks ;.

Features Cup holders Important safety notes G WARNING In order to help prevent spilling liquids on vehicle occupants and/or vehicle equipment, only use containers that fit into the cup holder. Use lids on open containers and do not fill containers to a height where the contents, especially hot liquids, could spill during braking, vehicle maneuvers, or in an accident. Liquids spilled on vehicle occupants may cause serious personal injury. Liquids spilled on vehicle equipment may cause damage not covered by the Mercedes-Benz Limited Warranty. When not in use, keep the cup holder closed. An open cup holder may cause injury to you or others when contacted during braking, vehicle maneuvers, or in an accident. Keep in mind that objects placed in the cup holder may come loose during braking, vehicle maneuvers, or in an accident and be thrown around in the vehicle interior. Objects thrown around in the vehicle interior may cause an accident and/or serious personal injury.

Cup holder in the front-compartment center console You can remove the cup holder to clean it. Clean with clear, lukewarm water only.

Bag hooks ! The bag hook can bear a maximum load of 6.6 lbs (3 kg). Do not use it to secure a load.

X Pull bag hook ; down by tab :.

Stowage well under the trunk floor

: Stowage well ; Hook = Trunk floor cover

392 Features

Sun visors Overview of sun visors G WARNING Do not use the vanity mirror while driving. Keep the vanity mirrors in the sun visors closed while the vehicle is in motion. Reflected glare can endanger you and others.

: Mirror light ; Bracket = Retaining clip, e.g. for a car park ticket ? Vanity mirror A Mirror cover

Vanity mirror in the sun visor Mirror light : only functions if the sun visor is clipped into retainer ; and mirror cover A has been folded up.

Glare from the side X Fold down the sun visor. X Pull the sun visor out of retainer ;. X Swing the sun visor to the side.

X To open: press marking :. X To remove: pull the cup holder upwards in

the direction of the arrow by silver handle ;.

X To insert: press down until it engages.

Observe the installation position indicated by "Front".

Cup holder in the rear seat armrest ! Do not sit on or support your body weight on the rear seat armrest when it is folded down, as you could otherwise damage it. ! Close the cup holder before folding the rear seat armrest up. Otherwise, the cup holder could be damaged.

X Fold down the rear seat armrest. X To open: press the front of cup holder :.

Cup holder : extends automatically.

X To close: slide the cup holder back until it

engages.

Rear window roller sunblind Important safety notes G WARNING When leaving the vehicle, always remove the SmartKey from the ignition lock. Always take the SmartKey with you and lock the vehicle. Do not leave children unattended in the vehicle, even if they are secured in a child restraint system, or with access to an unlocked vehicle. A child's unsupervised access to a vehicle could result in an accident and/or serious personal injury. The children could: Rinjure themselves on parts of the vehicle Rbe seriously or fatally injured through

excessive exposure to extreme heat or cold Rinjure themselves or cause an accident with

vehicle equipment that can be operated even if the SmartKey is removed from the ignition lock or removed from the vehicle, such as seat adjustment, steering wheel adjustment, or the memory function

If children open a door, they could injure other persons or get out of the vehicle and injure themselves or be injured by following traffic. Do not expose the child restraint system to direct sunlight. The child restraint system's metal parts, for example, could become very hot, and the child could be burned on these parts. G WARNING When adjusting a roller sunblind, the roller blind moves up or down. You might become trapped in the process. In the event of danger, briefly press the button for the roller sunblind to change the roller blind's direction of movement.

Extending/retracting the roller sunblind ! Make sure that the roller sunblind can

move freely. Otherwise, the roller sunblind or other objects could be damaged.

Features

393

At temperatures below Ò20 †, the window blind cannot be operated.

X Turn the key to position 2 in the ignition

lock.

X To extend or retract: briefly press

button :. The roller sunblind fully extends or fully retracts.

X To stop: briefly press button : again.

The roller sunblind stops briefly and moves back into the out-of-use position.

Ashtray Ashtray in the front-compartment center console

X To open: slide cover : forwards until it

engages.

X To remove the insert: push sliding

knob ? in the housing of the ashtray to the left. Ashtray insert = slides out slightly.

X Lift insert = up ; and out.

394 Features

X To re-install the insert: press insert =

into the holder until it engages.

X To close: press cover : briefly at the

front. The cover moves back.

Cigarette lighter G WARNING When leaving the vehicle, always remove the SmartKey from the ignition lock. Always take the SmartKey with you and lock the vehicle. Do not leave children unattended in the vehicle, even if they are secured in a child restraint system, or with access to an unlocked vehicle. A child's unsupervised access to a vehicle could result in an accident and/or serious personal injury. The children could: Rinjure themselves on parts of the vehicle Rbe seriously or fatally injured through

excessive exposure to extreme heat or cold Rinjure themselves or cause an accident with

vehicle equipment that can be operated even if the SmartKey is removed from the ignition lock or removed from the vehicle, such as seat adjustment, steering wheel adjustment, or the memory function

If children open a door, they could injure other persons or get out of the vehicle and injure themselves or be injured by following traffic. Do not expose the child restraint system to direct sunlight. The child restraint system's metal parts, for example, could become very hot, and the child could be burned on these parts. G WARNING Never touch the heating element or sides of the lighter; they are extremely hot. Hold the knob only. Make sure any children traveling with you do not injure themselves or start a fire with the hot cigarette lighter.

X Turn the SmartKey to position 2 in the

X To open: slide cover : forwards until it

ignition lock.

engages.

X Press in cigarette lighter ;.

Cigarette lighter ; will pop out automatically when the heating element is red-hot.

X To close: press cover : briefly at the

front. The cover moves back.

12 V sockets Points to observe before use The sockets can be used for accessories, e.g. lamps or mobile phone chargers with a maximum current draw of 180 W (15 A). If you use the sockets for long periods when the engine is switched off, the battery may discharge. X Turn the SmartKey to position 1 in the

ignition lock.

i An emergency cut-out ensures that the on-board voltage does not drop too low. If the on-board voltage is too low, the power to the sockets is automatically cut. This ensures that there is sufficient power to start the engine.

Socket in the glove box

X Open the glove box (Y page 388). X Lift up the cover of socket :.

Socket in the trunk

X Lift up the cover of socket :.

mbrace Important safety notes ! A license agreement must exist in order to activate the mbrace service. Ensure that your system is activated and ready for use, and press the E MB Info call button to register. If any of the steps mentioned is not carried out, the system may not be activated.

Features

395

If you have questions about the activation, contact one of the following telephone assistance services: RUSA: Mercedes-Benz Customer

Assistance Center under 1-888-990-9007

RCanada: Customer Service at

1-888-923-8367

Shortly after successfully registering with the mbrace service, a user ID and password will be sent to you by post. You can use this password to log in to the mbrace section under "Owners Online" at http:// www.mbusa.com17. The mbrace system is available if: Rit has been activated and is operational. Rthe corresponding mobile phone network

is available for transmitting data to the Customer Center.

Ra service subscription is available. Rthe starter battery is sufficiently charged. i Determining the location of the vehicle on a map is only possible if there is sufficient GPS reception and the vehicle position can be forwarded to the Customer Center.

The mbrace system The mbrace system provides different services, e.g.: Rautomatic and manual emergency call RRoadside Assistance call RMB Info call To adjust the volume during an mbrace call, proceed as follows: X Press the W or X button on the

multifunction steering wheel.

or X Use the H volume controller of

COMAND (Y page 109).

17 USA only.

396 Features

You can find further information and a description of all available features under "Owners Online" at http:// www.mbusa.com18.

System self-test After you have switched on the ignition, the system carries out a self-diagnosis. G WARNING A malfunction in the system has been detected if one of the following conditions occurs: Rthe indicator lamp in the SOS button does

not light up during the system self- diagnosis.

Rthe indicator lamp in the º Roadside

Assistance button does not light up during the system self-diagnosis.

RThe indicator lamp in the E information

button does not light up during self- diagnosis of the system.

Rthe indicator lamp in the SOS button,

º Roadside Assistance button or E information button continues to be lit red after the system self-diagnosis. RThe Tele Aid Inoperative or Tele Aid Not Activated message appears in the multifunction display after the system self- test.

If a malfunction is indicated as outlined above, the system may not operate as expected. In the event of an emergency, assistance must be summoned by other means. Have the system checked at the nearest authorized Mercedes-Benz Center or contact the following service hotlines: RUSA: Response Center under

888-990-9007

RCanada: Customer Service at

1-888-923-8367

18 USA only.

Emergency call Important safety notes ! A license agreement must exist in order to activate the mbrace service. Ensure that your system is activated and ready for use, and press the E MB Info call button to register. If any of the steps mentioned is not carried out, the system may not be activated. If you have questions about the activation, contact one of the following telephone assistance services: RUSA: Mercedes-Benz Customer

Assistance Center under 1-888-990-9007

RCanada: Customer Service at

1-888-923-8367

An emergency call is dialed automatically if an air bag or Emergency Tensioning Device is triggered. i An mbrace emergency call that has been

initiated automatically cannot be terminated by the customer.

An emergency call can also be initiated manually. As soon as the emergency call has been initiated, the indicator lamp in the SOS button flashes. The Connecting Call message appears on the multifunction display. The COMAND display shows the Emergency Call Activated message. The audio output is muted. Once a connection has been established, the Call Connected message appears in the multifunction display. The COMAND display shows the Emergency Call Activated message.

All important information on the emergency is transmitted, for example: Rcurrent location of the vehicle (as

determined by the GPS system)

Rvehicle identification number Rinformation on the type of emergency i If the Emergency Call Activated message appears in the COMAND display, you cannot use other COMAND functions.

Shortly after the emergency call has been initiated, a voice connection is automatically established between the Mercedes-Benz Customer Assistance Center and the vehicle occupants. If the vehicle occupants respond, the Mercedes-Benz Customer Assistance Center attempts to get more information on the emergency. i If no vehicle occupant answers, an ambulance is immediately sent to the vehicle. G WARNING If the indicator lamp in the SOS button is flashing continuously and no voice connection to the Mercedes-Benz Customer Assistance Center was established, then the mbrace system could not initiate an emergency call (e.g. the relevant cellular phone network is not available). The message Call Failed appears in the multifunction display for approximately 10 seconds. Should this occur, assistance must be summoned by other means.

i During an emergency call, the

Bluetooth® connection on the phone is canceled automatically. After making the emergency call, the connection is automatically re-established.

Features

397

Making an emergency call

X To initiate an emergency call

manually: press cover : briefly to open it.

X Press SOS button ; briefly.

The indicator lamp in SOS button ; flashes until the emergency call is concluded.

X Wait for a voice connection to the

Mercedes-Benz Customer Assistance Center.

X After the emergency call is ended, close

cover :. G WARNING If you feel in any way in jeopardy when in the vehicle (e.g. smoke or fire in the vehicle, vehicle in a dangerous road location), please do not wait for voice contact after you have pressed the SOS button. Carefully leave the vehicle and move to a safe location. The Mercedes-Benz Customer Assistance Center will automatically contact local emergency officials with the vehicle's approximate location if they receive an automatic SOS signal and cannot make voice contact with the vehicle occupants.

Roadside Assistance button X Open the stowage compartment under the

armrest (Y page 389).

398 Features

for services such as repair work and/or towing. Further details are available in your mbrace manual. i The mbrace system failed to initiate a

Roadside Assistance call if: Rthe indicator lamp in Roadside Assistance button : is flashing continuously.

Rno voice connection to the Mercedes- Benz Customer Assistance Center was established.

This may be because the corresponding mobile phone network is not available. The Call Failed message appears in the multifunction display. The COMAND display shows the Call could not be connected! message. Press W to confirm the message.

X To end a call: press the ~ button on the

multifunction steering wheel.

or X Press the corresponding button for ending

a phone call on the COMAND telephone keypad.

MB Info call button X Open the stowage compartment under the

armrest (Y page 389).

X Press and hold MB Info call button : for

more than two seconds. This initiates a call to the Mercedes-Benz Customer Assistance Center. The indicator lamp in MB Info call button : flashes while

X Press and hold Roadside Assistance

button : for more than two seconds. This initiates a call to the Mercedes-Benz Customer Assistance Center. The indicator lamp in Roadside Assistance button : flashes while the call is active. The Connecting Call message appears in the multifunction display and the COMAND display. The audio output is muted. If a connection can be established, the Call Connected message appears in the multifunction display and in the COMAND display. If a cellular phone network is available and there is sufficient GPS reception, the mbrace system transmits data to the Mercedes-Benz Customer Assistance Center, for example: Rcurrent location of the vehicle Rvehicle identification number i The multifunction display and COMAND display show that an mbrace call is active. You can change to the navigation menu by pressing the S button during the call, for example. Voice output is not available.

A voice connection is established between the Mercedes-Benz Customer Assistance Center and the vehicle occupants. X Describe the type of assistance needed. The Mercedes-Benz Customer Assistance Center either sends a qualified Mercedes- Benz technician or organizes for your vehicle to be transported to the nearest authorized Mercedes-Benz Center. You may be charged

399

the connection is being established. The Connecting Call message appears in the multifunction display. The COMAND display shows the Information Call Activated message. The audio output is muted. If a connection can be established, the Call Connected message appears in the multifunction display. The COMAND display shows the Information Call Activated message. If a cellular phone network is available and there is sufficient GPS reception, the mbrace system transmits data to the Mercedes-Benz Customer Assistance Center, for example: Rcurrent location of the vehicle Rvehicle identification number i The COMAND display shows that an

mbrace call is active. You can change to the navigation menu by pressing the S button during the call, for example. Voice output is not available.

A voice connection is established between the Mercedes-Benz Customer Assistance Center and the vehicle occupants. You can obtain information on how to operate your vehicle's systems, on the location of the nearest authorized Mercedes-Benz Center, and on further products and services offered by Mercedes-Benz USA. Further details on the mbrace system can be found under http://www.mbusa.com19. Log in under "Owners Online". i The mbrace system failed to initiate an

MB Info call if: Rthe indicator lamp in MB Info call button : is flashing continuously.

Rno voice connection to the Mercedes- Benz Customer Assistance Center was established.

This may be because the corresponding mobile phone network is not available.

19 USA only.

Features The Call Failed message appears in the multifunction display. The COMAND display shows the Call could not be connected! message. Press W to confirm the message.

X To end a call: press the ~ button on the

multifunction steering wheel.

or X Press the corresponding button for ending

a phone call on the COMAND telephone keypad.

Call priority When service calls are active, e.g. Roadside Assistance or MB Info calls, an emergency call can still be initiated. In this case, an emergency call will take priority and override all other active calls. The indicator lamp of the respective button flashes until the call is ended. An emergency call can only be terminated by the Mercedes- Benz Customer Assistance Center. All other calls can be ended by pressing the ~ button on the multifunction steering wheel or the corresponding button for ending a telephone call on the COMAND telephone keypad.

Downloading destinations in COMAND i The components and operating principles

of COMAND can be found on (Y page 108).

i You can only use the Destination Download function if the vehicle is equipped with a navigation system.

Destination Download gives you access to a database with over 15 million points of interest (POIs)/important destinations that can be downloaded onto the navigation system of your vehicle. If you know the destination, you can download the address or obtain the location of points of interest

400 Features

(POIs)/important destinations in the surrounding area. You are prompted to confirm route guidance to the address entered. X Slide XVY and turn cVd the COMAND controller to select Yes and confirm by pressing W.

The system calculates the route and subsequently starts the route guidance with the address entered. i If you select No, the address can be stored in the address book.

i The Destination Download function is

available if the corresponding mobile phone network is available and data transfer is possible.

Route Assistance This service is part of the mbrace PLUS Package and cannot be purchased separately. i You can also use the Route Assistance

function if your vehicle is not equipped with a navigation system.

Within the framework of this service, you receive a professional and reliable form of navigation support without having to leave your vehicle. The customer service representative determines a suitable driving route based on your current vehicle position and the desired destination and guides you live through the current sections of the route.

Search & Send Points to observe before use i To use Search & Send, your vehicle must be equipped with mbrace and a navigation system. You must also have an mbrace service subscription.

"Search & Send" is a destination entry service. A destination which is determined by Google Maps® or Yahoo Local Maps® can be

forwarded directly to your vehicle's navigation system using TELEAID. Specifying and sending the destination address i Information about specific commands

such as address entry or sending an address can be found on (either of) the website(s). Each website works differently and is subject to change.

X Go to either http://

www.maps.google.com or http:// www.maps.yahoo.com and enter a destination address in the entry field.

X Press the relevant button on the website to send the destination address to the e-mail address of your mbrace account.

X When the "Send" dialog window appears:

In the relevant field, enter the e-mail address which you specified when activating your mbrace account.

X Click on "Send". Calling up destination addresses X Press the MB Info call button to load the

destination address to your vehicle's navigation system. A display message appears, asking whether navigation should be started. X Slide XVY and turn cVd the COMAND controller to select Yes and confirm by pressing W. The system calculates the route and subsequently starts the route guidance with the address entered. i If you select No, the address can be stored in the address book.

i If you have sent more than one

destination address, you have to make an info call to load each individual address. i Destination addresses are loaded in the same order as the order in which they were sent. If you own multiple Mercedes-Benz vehicles with mbrace and activated mbrace accounts:

Each destination address sent can be accessed by every vehicle which is connected with the relevant e-mail address.

Vehicle remote opening If you have unintentionally locked your vehicle (e.g. the SmartKey is still in the vehicle) and a replacement SmartKey is not available, the vehicle can be opened by a Mercedes-Benz Customer Assistance Center. The vehicle can be opened remotely up to four days after the ignition was last switched off. X Contact the following service hotlines:

RUSA: Mercedes-Benz Customer

Assistance Center under 1-800-FOR- MERCedes(1-800-367-6372) or 1-888-990-9007

RCanada: Customer Service at

1-888-923-8367

You will be asked for your password.

X Return to your vehicle at the time agreed upon with the Mercedes-Benz Customer Assistance Center.

X Pull the trunk lid handle for at least 20

seconds until the indicator lamp in the SOS button (Y page 396) flashes. The Connecting Call message appears on the multifunction display.

Alternatively, the vehicle can also be opened via the Internet or an iPhone in the "Owners Online" section using your ID number and password20. i Vehicle remote unlocking is only possible if the corresponding mobile phone network is accessible. The SOS button flashes and the Connecting Call message appears in the multifunction display to confirm that the command for vehicle remote unlocking has been received. If you pull the trunk handle for more than 20 seconds before receiving authorization

20 USA only.

Features

401

for remote unlocking, you must wait 15
minutes before you can pull the trunk lid handle again.

Vehicle remote closing If you forget to lock your vehicle but are no longer in the vicinity of the vehicle, it can be locked for you by the Mercedes-Benz Customer Assistance Center. The vehicle can be locked remotely up to four days after the ignition was last switched off. X Contact the following service hotlines:

RUSA: Mercedes-Benz Customer

Assistance Center under 1-800-FOR- MERCedes(1-800-367-6372) or 1-888-990-9007

RCanada: Customer Service at

1-888-923-8367

You will be asked for your PIN. The next time you are in your vehicle and switch on the ignition, the Tele Aid Doors Locked Remotely message appears in the multifunction display. Alternatively, the vehicle can also be locked via the Internet or an iPhone in the "Owners Online" section using your ID number and password. i The vehicle valet locking feature is

available when the relevant mobile phone network is available and data connection is possible.

Automatic vehicle data retrieval for the service due date Your vehicle comes with a function which improves the servicing of the vehicle considerably. Shortly before the service due date, mbrace sends important vehicle maintenance information to the Mercedes- Benz Customer Assistance Center. The Mercedes-Benz Customer Assistance Center then informs your authorized Mercedes-Benz Service Center of the work required. This

402 Features

happens automatically and does not require any action from the driver. This function allows the Mercedes-Benz Center to improve appointment planning significantly and ensures that your vehicle receives the best service possible. i The "Automatic retrieval of vehicle data for the service due date" function is only available if the relevant mobile phone network is available and a data connection is possible.

Service for recovering a stolen vehicle If your vehicle has been stolen: X Notify the police.

The police will issue a numbered incident report.

X This number will be forwarded to the Mercedes-Benz Customer Assistance Center together with your PIN. The Mercedes-Benz Customer Assistance Center then attempts to locate the mbrace system. The Mercedes-Benz Customer Assistance Center contacts you and the local law enforcement agency if the vehicle is located. However, only the law enforcement agency is informed of the location of the vehicle.

i If the anti-theft alarm system is active for

longer than 30 seconds, mbrace automatically informs the Mercedes-Benz Customer Assistance Center.

Garage door opener Important safety notes The HomeLink® garage door opener integrated in the rear-view mirror allows you to operate up to three different door and gate systems.

i Certain garage door drives are

incompatible with the integrated garage door opener. If you have difficulty programming the integrated garage door opener, contact an authorized Mercedes- Benz Center or call one of the following telephone hotlines: RUSA: Mercedes-Benz Customer

Assistance Center at 1-800-FOR-MERCedes

RCanada: Customer Service at

1-800-387-0100

G WARNING Before programming the integrated remote control to a garage door opener or gate operator, make sure people and objects are out of the way of the device to prevent potential harm or damage. When programming a garage door opener, the door moves up or down. When programming a gate operator, the gate opens or closes. Do not use the integrated remote control with any garage door opener that lacks safety stop and reverse features as required by U.S. federal safety standards (this includes any garage door opener model manufactured before April 1, 1982). A garage door that cannot detect an object - signaling the door to stop and reverse - does not meet current U.S. federal safety standards. When programming a garage door opener, park vehicle outside the garage. Do not run the engine while programming the integrated remote control. Inhalation of exhaust gas is hazardous to your health. All exhaust gas contains carbon monoxide (CO), and inhaling it can cause unconsciousness and possible death. All exhaust gas contains carbon monoxide (CO), and inhaling it can cause unconsciousness and possible death.

i USA only:

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and 2. this device must accept any interference received, including interference that may cause undesired operation. Any unauthorized modification to this device could void the user's authority to operate the equipment. FCC ID: CB2HMIHL4

i Canada only:

This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause interference, and 2. this device must accept any interference received, including interference that may cause undesired operation of the device. Any unauthorized modification to this device could void the user's authority to operate the equipment. IC: 279B-HMIHL4

Programming the integrated garage door opener on the rear-view mirror Programming G WARNING Only press the transmitter button on the integrated garage door opener if there are no persons or objects present within the sweep of the garage door. People could otherwise be injured by the movement of the door.

Features

403

Integrated garage door opener on the rear-view mirror Garage door remote control A is not part of this integrated garage door opener. i To achieve the best result, insert new batteries in garage door remote control A before programming.

X Before programming for the first time, clear the memory of the integrated garage door opener (Y page 405).

X Turn the SmartKey to position 2 in the

ignition lock.

X Press and hold one of transmitter

buttons ; to ? on the integrated garage door opener. Indicator lamp : starts to flash yellow after a short period.

i Indicator lamp : flashes yellow

immediately after the transmitter button has been stored for the first time. If the transmitter button has already been programmed, indicator lamp : does not flash yellow until 10 seconds have elapsed.

X Release the transmitter button. X Point transmitter button B of garage door remote control A towards the transmitter buttons on the rear-view mirror at a distance of 2 to 8 inches (5 to 20 cm). i The distance required between garage

door remote control A and the integrated garage door opener depends on the system of the garage door drive. You might require several attempts. You should test every

404 Features

position for at least 25 seconds before trying another position.

X Press and hold transmitter button B on

garage door remote control A until indicator lamp : lights up green. Programming is complete if indicator lamp : lights up or flashes green.

X Release transmitter button ;, = or ? on the integrated garage door opener and the transmitter button on garage door remote control B.

If indicator lamp : lights up red: X Repeat the programming procedure for the transmitter button. When doing so, vary the distance between the garage door remote control and the rear-view mirror.

i If the indicator lamp flashes green after successful programming, the garage door system is operating on a rolling code. After programming, you must synchronize the garage door opener integrated in the rear- view mirror with the receiver of the garage door system.

Synchronizing the rolling code Your vehicle must be within range of the garage or gate opener drive. Make sure that neither your vehicle nor any persons/objects are present within the sweep of the door or gate. Observe the safety notes when performing the rolling code synchronization. X Turn the SmartKey to position 2 in the

ignition lock.

X Press the programming button of the door

or gate drive (see the door or gate drive operating instructions, e.g. under "Programming of additional remote controls").

i You now normally have 30 seconds to

initiate the next step.

X Press the previously programmed

transmitter button of the HomeLink®

integrated garage door opener repeatedly in succession until the door opens. The rolling code synchronization is then complete.

Notes on programming the remote control Canadian radio frequency laws require a "break" (or interruption) of the transmission signals after broadcasting for a few seconds. These signals may not therefore last long enough for the integrated garage door opener to recognize the signal during programming. Comparable with Canadian law, some U.S. garage door openers also have a built-in "interruption". If you live in Canada or have difficulties programming the garage door opener (regardless of where you live) when using the programming steps (see above), proceed as follows: X Press and hold one of transmitter

buttons ; to ? of the integrated garage door opener. Indicator lamp : starts to flash yellow after a short period.

X Release the transmitter button. X Press transmitter button B of the garage

door remote control and hold for two seconds, then release for two seconds, then press again and hold for two seconds.

X Repeat this sequence on transmitter button B of the garage door remote control until indicator lamp : is green. Repeat the process if indicator lamp : turns red.

X Continue with the other programming

steps (see above).

Problems when programming If you are experiencing problems programming the integrated garage door opener on the rear-view mirror, take note of the following instructions: Rcheck the transmission frequency of

garage door remote control A (usually

Features

405

found on the reverse side of the remote control). The integrated garage door opener is compatible with devices that can be operated with units in a frequency range of 280 to 390 MHz.

Rchange the batteries in garage door remote control A. This increases the probability that garage door remote control A will send a strong and precise signal to the integrated garage door opener on the rear- view mirror.

Rwhen programming, hold garage door

remote control A at different distances and angles from the transmitter button that you are programming. Try different angles at a distance between 2 and 12 inches (5
to 30 cm) or the same angle at varying distances.

Rif another remote control for the same

garage door drive is available, repeat the same programming steps with this remote control. Before you perform the steps of the operation, make sure that there are new batteries in the garage door remote control.

Rnote that some remote controls only

transmit for a limited amount of time (the indicator lamp on the remote control goes out). Press the remote control button again before it stops transmitting.

Ralign the antenna cable of the garage door

opener unit. This can improve signal reception/transmission.

Opening/closing the garage door Once programmed, the integrated garage door opener will assume the function of the garage door system's remote control. Please also read the operating instructions for the garage door system.

X Turn the SmartKey to position 2 in the

ignition lock.

X Press transmitter button ;, = or ? in the

overhead control panel that you have programmed to operate the garage door. Garage door system with a fixed code: indicator lamp : lights up green. Garage door system with a rolling code: indicator lamp : flashes green.

i The transmitter will transmit a signal for as long as the transmitter button is being pressed. After a maximum of ten seconds, transmission is terminated and indicator lamp : flashes yellow. Press the transmitter button again, if necessary.

Clearing the memory of the integrated garage door opener on the rear-view mirror X Turn the SmartKey to position 2 in the

ignition lock.

X Press transmitter buttons ; and ?.

The indicator lamp lights up yellow.

X Press and hold transmitter buttons ;

and ? until the indicator lamp turns green.

i Make sure that you clear the memory of the integrated garage door opener before selling the vehicle.

Floormat on the driver's side G WARNING Whenever you are using a floormat, make sure there is enough clearance and that the floormat is securely fastened. The floormat should always be securely fastened using the fastening equipment. Before driving off, check that the floormat is securely in place and adjust it if necessary. A loose floormat could slip and hinder proper functioning of the pedals. Do not place several floormats on top of each other as this may impair pedal movement.

406 Features

X Slide the seat backwards. X To install: place the floormat in the

footwell.

X Press studs : onto retainers ;. X To remove: pull the floormat off

retainers ;.

X Remove the floormat.

Infrared reflective windshield The infrared reflecting glass prevents the vehicle interior from becoming too hot. It also blocks radio waves up into the gigahertz range.

Vehicles with Night View Assist : Areas permeable to radio waves (to the

left of the rain sensor cover)

; Rain sensor cover = Areas permeable to radio waves In order to operate radio-controlled equipment, e.g. toll recording systems, areas : and = on the windshield are permeable to radio waves. In these areas, you can install radio-controlled systems. These areas can best be seen from outside the vehicle by observing the light reflected off the windshield.

Vehicles without Night View Assist : Areas permeable to radio waves (to the left and right of the rain sensor cover)

; Rain sensor cover = Areas permeable to radio waves

Useful information ............................ 408
Engine compartment ........................ 408
Maintenance ...................................... 413
Care .................................................... 414

407

G WARNING To help prevent personal injury, stay clear of moving parts when the hood is open and the engine is running. The radiator fan may continue to run for approximately 30 seconds or may even restart after the engine has been turned off. Stay clear of fan blades. G WARNING The engine is equipped with a transistorized ignition system. Because of the high voltage, it is dangerous to touch any components (ignition coils, spark plug sockets, diagnostic socket) of the ignition system: Rwith the engine running Rwhile starting the engine Rwhen the ignition is switched on and the

engine is turned manually

X Make sure that the windshield wipers are

switched off. G WARNING The windshield wipers and wiper linkage could be set in motion. When the hood is open, you or others could be injured by the wiper linkage. Make sure that the windshield wipers are switched off. Remove the SmartKey or make sure that no ignition position has been selected with KEYLESS-GO. All indicator lamps must be off in the instrument cluster.

408 Engine compartment

Useful information

i This Operator's Manual describes all models and all standard and optional equipment of your vehicle available at the time of publication of the Operator's Manual. Country-specific differences are possible. Please note that your vehicle may not be equipped with all features described. This also applies to safety- related systems and functions.

i Please read the information on qualified

specialist workshops (Y page 29).

Engine compartment Hood Opening the hood G WARNING Do not pull the release lever while the vehicle is in motion. Otherwise, the hood could be forced open by passing air flow. This could cause the hood to come loose and injure you and/or others. G WARNING Do not open the hood when the engine is overheated. You could be seriously injured. Observe the coolant temperature gauge to determine whether the engine may be overheated. If you see flames or smoke coming from the engine compartment, move away from the vehicle. Wait until the engine has cooled. If necessary, call the fire department. G WARNING There is a risk of injury if the hood is open, even if the engine is not running. Some engine components can become very hot. To avoid the risk of burns, only touch those components described in the Operator's Manual and observe the relevant safety notes.

X Pull release lever : for the hood.

The hood is released.

! Make sure that the windshield wipers are not folded away from the windshield. You could otherwise damage the windshield wipers or the hood.

X Reach into the gap, pull hood catch

handle ; up and lift the hood. Once you have lifted the hood about 15 inches (40 cm), it is automatically opened the rest of the way and held open by the gas-filled struts.

Closing the hood G WARNING When closing the hood, use extreme caution not to catch hands or fingers. Be careful that you do not close the hood on anyone. Make sure the hood is securely engaged before driving off. Do not continue driving if the hood can no longer engage after an accident, for example. The hood could otherwise come loose while the vehicle is in motion and injure you and/or others.

X Lower the hood and let it fall from a height

of approximately 8 inches (20 cm).

X Check that the hood has engaged properly. If the hood can be raised slightly, it is not properly engaged. Open it again and close it with a little more force.

Engine compartment

409

Engine oil Notes on the oil level Depending on the driving style, the vehicle consumes up to 0.9 US qts. (0.8 l) of oil over a distance of 600 miles (1000 km). The oil consumption may be higher than this when the vehicle is new or if you frequently drive at high engine speeds.

Checking the oil level using the oil dipstick On vehicles with a 12-cylinder engine, the oil level can be checked using the on-board computer. On all other models, the dipstick must be used to check the engine oil level.

X Park the vehicle on a level surface.

To check the oil level with the engine at operating temperature, switch the engine off and wait for approximately five minutes. X Pull oil dipstick : out of the dipstick guide

tube.

X Wipe off oil dipstick :. X Slowly slide oil dipstick : into the guide

tube to the stop, and take it out again. If the level is between MIN mark = and MAX mark ;, the oil level is correct.

X If the fuel level has sunk to MIN mark = or below, add 0.55 to 1.1 US qt (0.5 to 1.0 l) engine oil.

410 Engine compartment

Checking the oil level using the on- board computer On vehicles with a 12-cylinder engine, the oil level can be checked using the on-board computer. On all other models, the dipstick must be used to check the engine oil level. X Park the vehicle on a level surface.

To check the oil level with the engine at normal operating temperature, switch the engine off and wait for approximately five minutes.

X Make sure that the SmartKey is in position

2 in the ignition lock. X Press the ; or = button to select the Service menu. X Press the : or 9 button to select Engine Oil Level. X Press the a button. The multifunction display shows the following message: Engine Oil Level Measuring Now Measurement correct only if vehicle level. The measurement takes a few seconds. You will see one of the following messages in the multifunction display: REngine Oil Level OK RAdd 1.0 l Engine Oil At Next Refueling RAdd 1.5 l Engine Oil At Next Refueling RAdd 2.0 l Engine Oil At Next Refueling X Add oil if necessary. If the engine is at normal operating temperature and the Engine Oil Level Reduce Oil Level message appears, the engine oil level is too high. X Have excess oil siphoned off. ! Do not add too much oil. Adding too much oil can result in damage to the engine or the catalytic converter. Have excess oil siphoned off.

If the For Engine Oil Level Ignition Must be On message appears: X Turn the SmartKey to position 2 in the ignition lock. If the Need More Time to Check Engine Oil Level message appears: X If the engine is at normal operating

temperature: repeat the measurement after about five minutes. If the engine is not at normal operating temperature (e.g. if the engine was only started briefly): repeat the measurement after about 30 minutes. If the Engine Oil Level Not When Engine On message appears: X Switch off the engine. X If the engine is at normal operating

temperature: wait about five minutes before carrying out the measurement. If the engine is not at normal operating temperature, e.g. if the engine was only started briefly: wait about 30 minutes before carrying out the measurement.

i If you wish to cancel the measurement, press the % button on the multifunction steering wheel.

Adding engine oil G WARNING If engine oil comes into contact with hot engine parts, it may ignite and you could burn yourself. Do not spill any engine oil on hot engine parts. H Environmental note When adding oil, take care not to spill any. If oil enters the soil or waterways, it is harmful to the environment.

! Use only engine oils and oil filters that

have been approved for vehicles equipped with a service system. A list of the engine oils and oil filters tested and approved in accordance with the Mercedes-Benz

Specifications for Service Products can be called up by visiting http:// www.mbusa.com (USA only). More information about tested and approved engine oils and oil filters is available from any authorized Mercedes-Benz Center. Damage to the engine or exhaust system is caused by the following: Rusing engine oils and oil filters which

have not been specifically approved for the service system.

Rreplacing the engine oil or oil filter after the replacement interval required by the service system has elapsed Rusing engine oil additives.

! Do not add too much oil. If the oil level is above the "max" mark on the dipstick, too much oil has been added. This can lead to damage to the engine or the catalytic converter. Have excess oil siphoned off.

Example: engine oil cap X Turn cap : counterclockwise and remove

it.

X Add engine oil.

Vehicles with oil level measurement function in the on-board computer: observe the information in the on-board computer when doing so. Vehicles with oil dipstick: if the oil level is at or below the MIN mark on the oil dipstick, add 0.55 to 1.1 US qt (0.5 to 1.0 l) engine oil.

Engine compartment

411

X Replace cap : on the filler neck and turn

clockwise. Ensure that the cap locks into place securely.

X Check the oil level again with the oil dipstick (Y page 409) or the on-board computer (Y page 410).

Further information on engine oil (Y page 478).

Checking and adding other service products Checking the coolant level Only check the coolant level when the vehicle is on a level surface and the engine has cooled down. X Turn the SmartKey to position

2 (Y page 267) in the ignition lock. On vehicles with KEYLESS-GO, press the Start/Stop button twice (Y page 267).

X Check the coolant temperature display in

the instrument cluster. The coolant temperature must be below 158 ‡ (70 †). G WARNING In order to avoid any potentially serious burns: Ruse extreme caution when opening the hood if there are any signs of steam or coolant leaking from the cooling system, or if the coolant temperature display indicates that the coolant is overheated.

Rdo not remove the pressure cap on the

coolant reservoir if the coolant temperature is above 158 ‡ (70 †). Allow the engine to cool down before removing the cap. The coolant reservoir contains hot fluid and is under pressure.

Rusing a rag, slowly turn the cap

approximately 1/2 turn to relieve excess pressure. If opened immediately, scalding

412 Engine compartment

hot fluid and steam will be blown out under pressure.

Rdo not spill antifreeze on hot engine parts. Antifreeze contains ethylene glycol which may burn if it comes into contact with hot engine parts.

X Slowly turn cap : half a turn counter- clockwise and allow excess pressure to escape.

X Turn cap : further counter-clockwise and

remove it. If the coolant is at the level of marker bar = in the filler neck when cold, there is enough coolant in coolant expansion tank ;. If the coolant is approximately 0.6 in (1.5 cm) above marker bar = in the filler neck when warm, there is enough coolant in coolant expansion tank ;.

X If necessary, add coolant that has been tested and approved by Mercedes-Benz.

X Replace cap : and turn it clockwise as far

as it will go.

For further information on coolant, see (Y page 479).

Windshield washer system and headlamp cleaning system The washer fluid reservoir is used for both the windshield washer system and the headlamp cleaning system. i Vehicle components and their service

products must match. You should,

therefore, only use products that have been tested and approved by Mercedes-Benz. Information on tested and approved products can be obtained at any authorized Mercedes-Benz Center or on the Internet at http://www.mbusa.com (USA only). G WARNING Washer solvent/antifreeze is highly flammable. Do not spill washer solvent/ antifreeze on hot engine parts, because it may ignite and burn. You could be seriously burned.

! At temperatures below freezing: always fill the washer fluid reservoir with a mix of water and windshield washer concentrate (e.g. MB WinterFit). There is otherwise a risk of damaging the windshield washer system/headlamp cleaning system.

! Only use washer fluid concentrate which

is suitable for plastic lenses. Unsuitable washer fluid concentrate could damage the plastic lenses of the headlamps.

! Do not add distilled or de-ionized water to the washer fluid container. Otherwise, the level sensor may be damaged.

i Add windshield washer concentrate, e.g. MB SummerFit, to the washer fluid all year round.

Example: washer fluid reservoir X Mix the windshield washer fluid in a

container beforehand.

X At temperatures above freezing: fill the washer fluid reservoir with a mix of water

and windshield washer concentrate (e.g. MB SummerFit).

X At temperatures below freezing: fill the washer fluid reservoir with a mix of water and windshield washer concentrate (e.g. MB WinterFit). Adapt the mixing ratio to the outside temperature. For information on the mixing ratio (Y page 480).

X To open: pull cap : upwards by the tab. X Add the premixed washer fluid. X To close: press cap : onto the filler neck

until it engages.

Brake fluid level ! If you notice that the brake fluid level in the brake fluid reservoir has fallen to the MIN mark or less, check the brake system immediately for leaks. Also check the thickness of the brake linings. Contact a qualified specialist workshop, e.g. an authorized Mercedes-Benz Center immediately. Do not add brake fluid. This does not correct the error.

Only check the brake fluid level when the vehicle is stationary and on a level surface.

The brake fluid level is correct if it is between MIN marking ; and MAX marking : on the brake fluid reservoir.

Maintenance 413

Maintenance Service interval display Service messages Information on the type of service and service intervals (see separate Service Booklet). You can obtain further information from an authorized Mercedes-Benz Center or at http://www.mbusa.com (USA only). The service interval display informs you of the next service due date. If a service due date has been exceeded, you also hear an acoustic signal. The multifunction display shows a service message for a few seconds, e.g. Next service A due in .. days Service A due Service A overdue by .. days The letter indicates how much time the workshop will require to carry out the service work. The letters displayed range from A for a short service duration to H for a long service duration. The service interval display does not take into account any periods of time during which the battery is disconnected. Maintaining the time-dependent service schedule: X Note down the service due date displayed

in the multifunction display before disconnecting the battery.

or X Subtract the battery disconnection periods from the service date shown on the display after reconnecting the battery.

i The service interval display does not provide any information regarding the engine's oil level. Observe the notes on the engine oil level (Y page 409).

414 Care

Hiding a service message X Press the % or a button on the

steering wheel.

Displaying service messages X Switch on the ignition. X Press = or ; on the steering wheel to select the Service menu. X Press 9 or : to select the ASSYST PLUS submenu and press a to confirm. The service due date appears in the multifunction display.

Please bear the following in mind Resetting service interval display If the qualified specialist workshop, e.g. a Mercedes-Benz Center, carried out the maintenance work, the service interval display will be reset. Further information, on maintenance for example, can be obtained at an authorized Mercedes-Benz Center or directly from Mercedes-Benz. ! If the service interval display has been

reset unintentionally, have the setting corrected at a Mercedes-Benz Center. Have service work carried out as described