2010 Mercedes-benz C Class Owners Manual

Position B represents the charged battery of another vehicle or an equivalent starter pack. X Slide cover : from positive terminal = in

direction of arrow.

! Never invert the terminal connections!

X Connect positive terminal ; of charged

battery B with positive terminal = with a jumper cable. Clamp the cable to positive terminal ; of charged battery B first. X Start engine of the vehicle with charged

battery B and run at idle speed.

204_AKB; 5; 23, en-US d2ureepe,

2009-07-16T17:54:06+02:00 - Seite 325
Version: 2.11.8.1

X Connect negative terminal ? of charged battery B with negative terminal A with a jumper cable. Clamp the cable to negative terminal ? of charged battery B first.

X Start engine of the vehicle with the

discharged battery and run at idle speed. You can now turn on the electrical consumers. Do not switch on the headlamps under any circumstances.

X Remove the jumper cables from negative

terminals ? and A first.

X Remove the jumper cables from positive

terminals ; and =. You can now switch on the headlamps. X Slide cover : from positive terminal =

back.

X Have the battery checked at the nearest

authorized Mercedes-Benz Center.

Towing the vehicle Safety notes Mercedes-Benz recommends that the vehicle be transported with all wheels off the ground using flatbed or appropriate wheel lift/dolly equipment. This method is preferable to other types of towing. ! To prevent damage during transport, do

not tie down vehicle by its chassis or suspension parts.

If circumstances do not permit the recommended towing methods, the vehicle may be towed with all wheels on the ground or front axle raised (except vehicles with 4MATIC) only so far as necessary to have the vehicle moved to a safe location where the recommended towing methods can be employed. ! Before towing the vehicle observe the

following instructions: RVehicles with automatic transmission and/or 4MATIC: Do not tow-start the

Towing the vehicle 325

vehicle. You could otherwise seriously damage the automatic transmission which is not covered by the Mercedes- Benz Limited Warranty.

RDo not tow with sling-type equipment. Towing with sling-type equipment over bumpy roads will damage radiator and supports.

RTowing of the vehicle should only be

done using the properly installed towing eye bolt. Never attach a tow cable, tow rope or tow rod to the vehicle chassis, frame or suspension parts.

G Warning! With the engine not running, there is no power assistance for the brake and steering systems. In this case, it is important to keep in mind that a considerably higher degree of effort is necessary to brake and steer the vehicle. Adapt your driving accordingly.

! Avoid pulling the vehicle abruptly or

diagonally, since it could result in damage to the chassis alignment.

! Do not use the towing eye bolt for

recovery, as this could damage the vehicle. If in doubt, recover the vehicle with a crane.

i If the battery is disconnected or

discharged Rthe SmartKey will not turn in the starter

switch

RVehicles with automatic transmission:

the automatic transmission will remain in park position P

For more information see “Battery” (Y page 321) or “Jump starting” (Y page 323). Vehicles with automatic transmission: For information on manually unlocking the gear selector lever, see (Y page 311).

204_AKB; 5; 23, en-US d2ureepe,

2009-07-16T17:54:06+02:00 - Seite 326
Version: 2.11.8.1

326 Towing the vehicle

Installing towing eye bolt Depending on whether you are towing a vehicle or you are being towed, the towing eye bolt can be screwed into threaded holes which are located behind covers on each bumper. The towing eye bolt is supplied with the vehicle tool kit, located underneath the trunk floor (Y page 268). X Take the vehicle tool kit out of the trunk.

Removing cover in front bumper

X Press mark on cover : as indicated by the

arrow.

X Lift cover : off to reveal the threaded hole

for the towing eye bolt.

Removing cover in rear bumper G Warning! In order to avoid possible serious burns or injury, use extreme caution when removing the rear cover, because the rear exhaust pipe is extremely hot.

X Press mark on cover : as indicated by the

arrow.

X Lift cover : off to reveal the threaded hole

for the towing eye bolt.

Fixing towing eye bolt

Example illustration front bumper X Take the towing eye bolt and, if so

equipped, the wheel wrench from the vehicle tool kit (Y page 268).

X Screw towing eye bolt ; clockwise into

threaded hole to its stop.

X Insert wheel wrench into towing eye and tighten towing eye bolt ; by turning it clockwise.

or X If your vehicle is not equipped with a wheel

wrench, use a suitable object to turn the towing eye bolt.

204_AKB; 5; 23, en-US d2ureepe,

2009-07-16T17:54:06+02:00 - Seite 327
Version: 2.11.8.1

Towing the vehicle 327

X Vehicles with manual transmission: Shift the manual transmission into the neutral position (no gear selected).

or X Vehicles with automatic transmission: Shift

the automatic transmission into neutral position N.

X Release the brake pedal. X If engaged, release the parking brake. X Switch on the hazard warning flasher

(Y page 93).

! The vehicle may be towed only for

distances up to 30 miles (50 km) and at a speed not to exceed 30 mph (50 km/h).

i While being towed with the hazard

warning flasher in use, use the combination switch in the usual manner to signal turns. Only the selected turn signal will operate. Upon canceling the turn signal, the hazard warning flasher will operate again.

Towing with front axle raised ! The vehicle may be towed only for

distances up to 30 miles (50 km) and at a speed not to exceed 30 mph (50 km/h).

! Vehicles with 4MATIC: Do not tow with

one axle raised. Doing so could damage the transfer case, which is not covered by the Mercedes-Benz Limited Warranty. All wheels must be on or off the ground. Observe instructions for towing the vehicle with all wheels on the ground.

X Make sure the ignition is switched on. X With the vehicle at a standstill, depress the

brake pedal and keep it pressed.

Removing towing eye bolt X Loosen towing eye bolt ; by turning it

counterclockwise.

X Unscrew towing eye bolt ;. X Store the towing eye bolt ; and wheel

wrench back into the vehicle tool kit.

Towing with all wheels on the ground G Warning! If circumstances require towing the vehicle with all wheels on the ground, always tow with a tow bar if: Rthe engine will not run Rthere is a malfunction in the brake system Rthere is a malfunction in the power supply

or in the vehicle’s electrical system

This is necessary to adequately control the towed vehicle. Prior to towing the vehicle with all wheels on the ground, make sure the SmartKey is in starter switch position 2. If the SmartKey is left in the starter switch position 0 for an extended period of time, it can no longer be turned in the switch. In this case, the steering is locked. To unlock, remove SmartKey from starter switch and reinsert. G Warning! With the engine not running, there is no power assistance for the brake and steering systems. In this case, it is important to keep in mind that a considerably higher degree of effort is necessary to brake and steer the vehicle. Adapt your driving accordingly.

X Make sure the ignition is switched on. X With the vehicle at a standstill, depress the

brake pedal and keep it pressed.

204_AKB; 5; 23, en-US d2ureepe,

328 Fuses

X Vehicles with manual transmission: Shift the manual transmission into the neutral position (no gear selected).

or X Vehicles with automatic transmission: Shift

the automatic transmission into neutral position N.

X Release the brake pedal. X If engaged, release the parking brake. X Switch off the automatic central locking

(Y page 135).

X Switch off the ignition and leave the

SmartKey in the starter switch.

X Switch on the hazard warning flasher

(Y page 93).

! Vehicles without 4MATIC:

Because the ESP® operates automatically, the engine and ignition must be shut off (SmartKey in starter switch position 0 or 1 or KEYLESS-GO start/stop button in position 0 or 1) when the vehicle is being towed with the front axle raised. Active braking action through the ESP® may otherwise seriously damage the brake system which is not covered by the Mercedes-Benz Limited Warranty.

Fuses Introduction The electrical fuses in your vehicle serve to switch off malfunctioning power circuits. If a fuse is blown, the components and systems secured by that fuse will stop operating. G Warning! Only use fuses approved by Mercedes-Benz with the specified amperage for the system in question and do not attempt to repair or bridge a blown fuse. Using other than approved fuses or using repaired or bridged fuses may cause an overload leading to a fire, and/or cause damage to electrical

2009-07-16T17:54:06+02:00 - Seite 328
Version: 2.11.8.1

components and/or systems. Have the cause determined and remedied by an authorized Mercedes-Benz Center. A blown fuse must be replaced by an appropriate spare fuse (recognizable by its color or the fuse rating given on the fuse) of the amperage recommended in the fuse chart. Any Mercedes-Benz Center will be glad to advise you on this subject. i In case of a blown fuse contact Roadside

Assistance or an authorized Mercedes- Benz Center.

If a newly inserted fuse blows again, have the cause determined and rectified by an authorized Mercedes-Benz Center. The fuse chart is located in the trunk with the vehicle tool kit (Y page 268). The fuse chart explains the fuse allocation and fuse amperages.

Before replacing fuses X Engage the parking brake. X Make sure the automatic transmission is in

park position P (manual transmission to Neutral).

X Switch off all electrical consumers. X Turn off the engine. X Remove the SmartKey from the starter

switch.

X Vehicles with KEYLESS-GO: Open the

driver’s door (this puts the starter switch in position 0, same as with the SmartKey removed from the starter switch). The driver’s door then can be closed again.

Fuse box in passenger compartment ! Do not use sharp objects such as a

screwdriver to open the fuse box cover in the dashboard. You could damage the fuse box cover or the dashboard.

204_AKB; 5; 23, en-US d2ureepe,

2009-07-16T17:54:06+02:00 - Seite 329
Version: 2.11.8.1

Fuses

329

Fuse box in engine compartment X Open the hood.

X Open the driver’s door. X Opening: Using your hands, pull fuse box

cover : in direction of arrow = and remove in direction of arrow ;.

X Closing: Hook fuse box cover : into the

opening at the front.

X Press fuse box cover : back on until it

engages.

! The fuse box cover must be properly

positioned as described. Otherwise, moisture or dirt could enter the fuse box and possibly impair fuse operation.

Fuse box in trunk

X Open the trunk. X Opening: Turn lock : clockwise. X Pull cover ; downward in direction of

arrow.

X Closing: Press cover ; backward. X Turn lock : counterclockwise.

X With a dry cloth, remove any moisture from

fuse box cover.

X Opening: Release wire ; from fuse box

cover.

X Release clamps :. X Remove fuse box cover. X Closing: Make sure the sealing rubber is

positioned properly.

X Press fuse box cover down and secure with

clamps :.

X Fasten wire ; on fuse box cover. ! The fuse box cover must be properly

positioned as described. Otherwise, moisture or dirt could enter the fuse box and possibly impair fuse operation.

X Close the hood after checking or replacing

fuses.

204_AKB; 5; 23, en-US d2ureepe,

330

2009-07-16T17:54:06+02:00 - Seite 330
Version: 2.11.8.1

204_AKB; 5; 23, en-US d2ureepe,

2009-07-16T17:54:06+02:00 - Seite 331
Version: 2.11.8.1

331

Vehicle equipment ............................ 332
Parts service ..................................... 332
Warranty coverage ........................... 332
Identification labels .......................... 332
Vehicle specification C 250
(204.052) ........................................... 334
Vehicle specification C 250 Sport (204.052) ........................................... 334
Vehicle specification C 250
4MATIC (204.085) ............................. 335
Vehicle specification C 250
4MATIC Sport (204.085) .................. 336
Vehicle specification C 300
(204.054) ........................................... 337
Vehicle specification C 300 Sport (204.054) ........................................... 338
Vehicle specification C 300
4MATIC (204.081) ............................. 339
Vehicle specification C 300
4MATIC Sport (204.081) .................. 340
Vehicle specification C 350
(204.056) ........................................... 341
Vehicle specification C 350 Sport (204.056) ........................................... 342
Vehicle specification C 350
4MATIC (204.087) ............................. 343
Vehicle specification C 63 AMG (204.077) ........................................... 343
Rims and tires ................................... 344
Fuels, coolants, lubricants, etc. ...... 349

204_AKB; 5; 23, en-US d2ureepe,

2009-07-16T17:54:06+02:00 - Seite 332
Version: 2.11.8.1

332

Identification labels

RNew Vehicle Limited Warranty REmission System Warranty REmission Performance Warranty RCalifornia, Connecticut, Maine,

Massachusetts, New York, Pennsylvania, Rhode Island, and Vermont Emission Control Systems Warranty

RState Warranty Enforcement Laws (Lemon

Laws)

Replacement parts and accessories are covered by the Mercedes-Benz Parts and Accessories warranties, copies of which are available at any authorized Mercedes-Benz Center.

Loss of Service and Warranty Information booklet Should you lose your Service and Warranty Information booklet, have an authorized Mercedes-Benz Center arrange for a replacement. It will be mailed to you.

Identification labels

Vehicle equipment

i This Operator’s Manual describes all

features, standard or optional, potentially available for your vehicle at the time of purchase. Please be aware that your vehicle might not be equipped with all features described in this manual.

Parts service

All authorized Mercedes-Benz Centers maintain a stock of Genuine Mercedes-Benz Parts required for maintenance and repair work. In addition, strategically located parts distribution centers provide quick and reliable parts service. More than 300 000 different parts for Mercedes-Benz models are available. Genuine Mercedes-Benz Parts are subjected to stringent quality inspections. Each part has been specifically developed, manufactured or selected for and adapted to Mercedes-Benz vehicles. Therefore, Genuine Mercedes-Benz Parts should be installed. ! Do not use non-genuine Mercedes-Benz parts and accessories not authorized by Mercedes-Benz. Doing so could damage the vehicle, which is not covered by the Mercedes-Benz Limited Warranty. Also, it could compromise the vehicle’s durability or safety.

Warranty coverage

Your vehicle is covered under the terms of the warranties printed in the Service and Warranty Information booklet. Your authorized Mercedes-Benz Center will exchange or repair any defective parts originally installed in the vehicle in accordance with the terms of the following warranties:

204_AKB; 5; 23, en-US d2ureepe,

2009-07-16T17:54:06+02:00 - Seite 333
Version: 2.11.8.1

Identification labels

333

specific to each vehicle and may vary from data shown in the illustration. Refer to certification label on vehicle for actual data specific to your vehicle.

The Vehicle Identification Number (VIN) can be found Ron certification label : on the driver’s door

B-pillar

Rembossed underneath the carpet in the front passenger footwell (Y page 333)

Ron the lower edge of the windshield

(Y page 333)

X Move the front passenger seat backward

as far as possible (Y page 80).

X Fold carpet ? backward.

VIN A is now visible.

Example certification label (U.S. vehicles) ; VIN = Paintwork code

Example certification label (Canada vehicles) ; VIN = Paintwork code

i Data shown on certification label are for illustration purposes only. These data are

B Emission control information label, includes both federal and California certification exhaust emission standards

C VIN (on lower edge of windshield) D Engine number (engraved on engine)

i When ordering parts, please specify

vehicle identification and engine number.

204_AKB; 5; 23, en-US d2ureepe,

2009-07-16T17:54:06+02:00 - Seite 334
Version: 2.11.8.1

334 Vehicle specification C 250 Sport (204.052)

Vehicle specification C 250 (204.052)

Electrical system C 250

The quoted data apply only to the standard vehicle. Contact an authorized Mercedes- Benz Center for the corresponding data of all special bodies and special equipment. i The C 250 is available in Canada only.

Spark plugs, type Spark plugs, electrode gap Spark plugs, tightening torque

Bosch Y 7 MPP33
0.031 in (0.8 mm)

15 - 18 lb-ft (20 - 25 Nm)

Engine C 250

Engine, type Mode of operation

No. of cylinders Bore Stroke Total piston displacement Compression ratio Output acc. to SAE J 134921
Maximum torque acc. to SAE J 1349

272

4-stroke engine, gasoline injection

3.46 in (88.00 mm) 2.69 in (68.40 mm)

152.3 cu in (2 496 cm3)

11.4:1

201 hp/6 100 rpm (150 kW/6 100 rpm)

181 lb-ft/

2 900 - 5 500 rpm

(245 Nm/

2 900 - 5 500 rpm)

Maximum engine speed Firing order Poly-V-belt

6 500 rpm

1-4-3-6-2-5
2 401 mm

Electrical system C 250

Alternator Starter motor Battery

14 V/150 A 12 V/1.4 kW 12 V/74 Ah

Main dimensions C 250

Overall vehicle length Overall vehicle width22
Overall vehicle height Wheelbase Track, front Track, rear Turning circle

182.3 in (4 630 mm)

79.5 in (2 020 mm)

56.9 in (1 444 mm)

108.7 in (2 760 mm) 60.7 in (1 541 mm) 60.8 in (1 544 mm) 35.4 ft (10.8 m)

Weights C 250

Roof load Trunk load

max. 220 lb (100 kg) max. 220 lb (100 kg)

Vehicle specification C 250 Sport (204.052)

The quoted data apply only to the standard vehicle. Contact an authorized Mercedes- Benz Center for the corresponding data of all special bodies and special equipment. i The C 250 Sport is available in Canada

only.

21 Premium fuel required. Performance may vary with fuel octane rating. 22 Exterior rear view mirrors folded out.

204_AKB; 5; 23, en-US d2ureepe,

2009-07-16T17:54:06+02:00 - Seite 335
Version: 2.11.8.1

Vehicle specification C 250 4MATIC (204.085)

335

Engine C 250 Sport

Main dimensions C 250 Sport

Engine, type Mode of operation

No. of cylinders Bore Stroke Total piston displacement Compression ratio Output acc. to SAE J 134923
Maximum torque acc. to SAE J 1349

272

4-stroke engine, gasoline injection

3.46 in (88.00 mm) 2.69 in (68.40 mm)

152.3 cu in (2 496 cm3)

11.4:1

201 hp/6 100 rpm (150 kW/6 100 rpm)

181 lb-ft/

2 900 - 5 500 rpm

(245 Nm/

2 900 - 5 500 rpm)

Maximum engine speed Firing order Poly-V-belt

6 500 rpm

1-4-3-6-2-5
2 401 mm

Electrical system C 250 Sport 14 V/150 A 12 V/1.4 kW 12 V/74 Ah

Alternator Starter motor Battery Spark plugs, type Spark plugs, electrode gap Spark plugs, tightening torque

Bosch Y 7 MPP33
0.031 in (0.8 mm)

15 - 18 lb-ft (20 - 25 Nm)

Overall vehicle length Overall vehicle width24
Overall vehicle height Wheelbase Track, front Track, rear Turning circle

182.8 in (4 630 mm)

79.5 in (2 020 mm)

57.0 in (1 449 mm)

108.7 in (2 760 mm) 60.4 in (1 533 mm) 59.6 in (1 514 mm) 35.4 ft (10.8 m)

Weights C 250 Sport

Roof load Trunk load

max. 220 lb (100 kg) max. 220 lb (100 kg)

Vehicle specification C 250 4MATIC (204.085)

The quoted data apply only to the standard vehicle. Contact an authorized Mercedes- Benz Center for the corresponding data of all special bodies and special equipment. i The C 250 4MATIC is available in Canada

only.

Engine C 250 4MATIC 272

Engine, type Mode of operation

No. of cylinders Bore Stroke

4-stroke engine, gasoline injection

3.46 in (88.00 mm) 2.69 in (68.40 mm)

23 Premium fuel required. Performance may vary with fuel octane rating. 24 Exterior rear view mirrors folded out.

204_AKB; 5; 23, en-US d2ureepe,

2009-07-16T17:54:06+02:00 - Seite 336
Version: 2.11.8.1

336 Vehicle specification C 250 4MATIC Sport (204.085)

Engine C 250 4MATIC

Main dimensions C 250 4MATIC

Total piston displacement Compression ratio Output acc. to SAE J 134925
Maximum torque acc. to SAE J 1349

152.3 cu in (2 496 cm3)

11.4:1

201 hp/6 100 rpm (150 kW/6 100 rpm)

181 lb-ft/

2 900 - 5 500 rpm

(245 Nm/

2 900 - 5 500 rpm)

Maximum engine speed Firing order Poly-V-belt

6 500 rpm

1-4-3-6-2-5
2 401 mm

Electrical system C 250 4MATIC 14 V/150 A 12 V/1.4 kW 12 V/74 Ah

Alternator Starter motor Battery Spark plugs, type Spark plugs, electrode gap Spark plugs, tightening torque

15 - 18 lb-ft (20 - 25 Nm)

Main dimensions C 250 4MATIC

Overall vehicle length Overall vehicle width26
Overall vehicle height

182.8 in (4 630 mm)

79.5 in (2 020 mm)

56.9 in (1 445 mm)

Wheelbase Track, front Track, rear Turning circle

108.7 in (2 760 mm) 60.7 in (1 541 mm) 60.8 in (1 544 mm) 35.4 ft (10.8 m)

Weights C 250 4MATIC

Roof load Trunk load

max. 220 lb (100 kg) max. 220 lb (100 kg)

Vehicle specification C 250 4MATIC Sport (204.085)

The quoted data apply only to the standard vehicle. Contact an authorized Mercedes- Benz Center for the corresponding data of all special bodies and special equipment. i The C 250 4MATIC Sport is available in

Canada only.

Engine C 250 4MATIC Sport

272

4-stroke engine, gasoline injection

3.46 in (88.00 mm) 2.69 in (68.40 mm)

152.3 cu in (2 496 cm3)

11.4:1

201 hp/6 100 rpm (150 kW/6 100 rpm)

No. of cylinders Bore Stroke Total piston displacement Compression ratio Output acc. to SAE J 134927

Bosch Y 7 MPP33
0.031 in (0.8 mm)

Engine, type Mode of operation

25 Premium fuel required. Performance may vary with fuel octane rating. 26 Exterior rear view mirrors folded out. 27 Premium fuel required. Performance may vary with fuel octane rating.

204_AKB; 5; 23, en-US d2ureepe,

2009-07-16T17:54:06+02:00 - Seite 337
Version: 2.11.8.1

Vehicle specification C 300 (204.054)

337

Engine C 250 4MATIC Sport 181 lb-ft/

Maximum torque acc. to SAE J 1349

2 900 - 5 500 rpm

(245 Nm/

2 900 - 5 500 rpm)

Maximum engine speed Firing order Poly-V-belt

6 500 rpm

1-4-3-6-2-5
2 401 mm

14 V/150 A 12 V/1.4 kW 12 V/74 Ah

Electrical system C 250 4MATIC Sport Alternator Starter motor Battery Spark plugs, type Spark plugs, electrode gap Spark plugs, tightening torque

Bosch Y 7 MPP33
0.031 in (0.8 mm)

15 - 18 lb-ft (20 - 25 Nm)

79.5 in (2 020 mm)

Main dimensions C 250 4MATIC Sport Overall vehicle 182.8 in (4 630 mm) length Overall vehicle width28
Overall vehicle height Wheelbase Track, front Track, rear Turning circle

108.7 in (2 760 mm) 60.4 in (1 533 mm) 59.6 in (1 514 mm) 35.4 ft (10.8 m)

57.0 in (1 449 mm)

Weights C 250 4MATIC Sport

Roof load Trunk load

max. 220 lb (100 kg) max. 220 lb (100 kg)

Vehicle specification C 300 (204.054)

The quoted data apply only to the standard vehicle. Contact an authorized Mercedes- Benz Center for the corresponding data of all special bodies and special equipment.

Engine C 300

Engine, type Mode of operation

No. of cylinders Bore Stroke Total piston displacement Compression ratio Output acc. to SAE J 134929
Maximum torque acc. to SAE J 1349

272

4-stroke engine, gasoline injection

3.46 in (88.00 mm) 3.23 in (82.10 mm)

182.8 cu in (2 996 cm3)

11.3:1

228 hp/6 000 rpm (170 kW/6 000 rpm)

221 lb-ft/

2 500 - 5 000 rpm

(300 Nm/

2 500 - 5 000 rpm)

Maximum engine speed Firing order Poly-V-belt

6 500 rpm

1-4-3-6-2-5
2 401 mm

28 Exterior rear view mirrors folded out. 29 Premium fuel required. Performance may vary with fuel octane rating.

204_AKB; 5; 23, en-US d2ureepe,

2009-07-16T17:54:06+02:00 - Seite 338
Version: 2.11.8.1

338 Vehicle specification C 300 Sport (204.054)

Electrical system C 300

Alternator Starter motor Battery Spark plugs, type Spark plugs, electrode gap Spark plugs, tightening torque

14 V/150 A 12 V/1.4 kW 12 V/74 Ah

Bosch Y 7 MPP33
0.031 in (0.8 mm)

15 - 18 lb-ft (20 - 25 Nm)

Main dimensions C 300

Overall vehicle length Overall vehicle width30
Overall vehicle height

Wheelbase Track, front

Track, rear

Turning circle

182.8 in (4 630 mm)

79.2 in (2 012 mm)

57.0 in (1 449 mm)31
56.9 in (1 444 mm)32
108.7 in (2 760 mm) 60.4 in (1 533 mm)31
60.7 in (1 541 mm)32
59.6 in (1 514 mm)31
60.8 in (1 544 mm)32
35.4 ft (10.8 m)

Weights C 300

Roof load Trunk load

max. 220 lb (100 kg) max. 220 lb (100 kg)

Vehicle specification C 300 Sport (204.054)

The quoted data apply only to the standard vehicle. Contact an authorized Mercedes- Benz Center for the corresponding data of all special bodies and special equipment. i The C 300 Sport is available in the USA

only.

Engine C 300 Sport

Engine, type Mode of operation

No. of cylinders Bore Stroke Total piston displacement Compression ratio Output acc. to SAE J 134933
Maximum torque acc. to SAE J 1349

272

4-stroke engine, gasoline injection

3.46 in (88.00 mm) 3.23 in (82.10 mm)

182.8 cu in (2 996 cm3)

11.3:1

228 hp/6 000 rpm (170 kW/6 000 rpm)

221 lb-ft/

2 500 - 5 000 rpm

(300 Nm/

2 500 - 5 000 rpm)

Maximum engine speed Firing order Poly-V-belt

6 500 rpm

1-4-3-6-2-5
2 401 mm

30 Exterior rear view mirrors folded out. 31 Canada only. 32 USA only. 33 Premium fuel required. Performance may vary with fuel octane rating.

204_AKB; 5; 23, en-US d2ureepe,

2009-07-16T17:54:06+02:00 - Seite 339
Version: 2.11.8.1

Vehicle specification C 300 4MATIC (204.081)

339

Electrical system C 300 Sport 14 V/150 A 12 V/1.4 kW 12 V/74 Ah

Alternator Starter motor Battery Spark plugs, type Spark plugs, electrode gap Spark plugs, tightening torque

Bosch Y 7 MPP33
0.031 in (0.8 mm)

15 - 18 lb-ft (20 - 25 Nm)

Main dimensions C 300 Sport

Overall vehicle length Overall vehicle width34
Overall vehicle height Wheelbase Track, front Track, rear Turning circle

182.8 in (4 630 mm)

79.2 in (2 012 mm)

57.0 in (1 449 mm)

108.7 in (2 760 mm) 60.4 in (1 533 mm) 60.5 in (1 536 mm) 35.4 ft (10.8 m)

Weights C 300 Sport

Roof load Trunk load

max. 220 lb (100 kg) max. 220 lb (100 kg)

Vehicle specification C 300 4MATIC (204.081)

The quoted data apply only to the standard vehicle. Contact an authorized Mercedes- Benz Center for the corresponding data of all special bodies and special equipment.

Engine C 300 4MATIC 272

Engine, type Mode of operation

No. of cylinders Bore Stroke Total piston displacement Compression ratio Output acc. to SAE J 134935
Maximum torque acc. to SAE J 1349

4-stroke engine, gasoline injection

3.46 in (88.00 mm) 3.23 in (82.10 mm)

182.8 cu in (2 996 cm3)

11.3:1

228 hp/6 000 rpm (170 kW/6 000 rpm)

221 lb-ft/

2 500 - 5 000 rpm

(300 Nm/

2 500 - 5 000 rpm)

Maximum engine speed Firing order Poly-V-belt

6 500 rpm

1-4-3-6-2-5
2 401 mm

Electrical system C 300 4MATIC 14 V/150 A 12 V/1.4 kW 12 V/74 Ah

Alternator Starter motor Battery Spark plugs, type Spark plugs, electrode gap Spark plugs, tightening torque

Bosch Y 7 MPP33
0.031 in (0.8 mm)

15 - 18 lb-ft (20 - 25 Nm)

34 Exterior rear view mirrors folded out. 35 Premium fuel required. Performance may vary with fuel octane rating.

204_AKB; 5; 23, en-US d2ureepe,

2009-07-16T17:54:06+02:00 - Seite 340
Version: 2.11.8.1

340 Vehicle specification C 300 4MATIC Sport (204.081)

Main dimensions C 300 4MATIC

Engine C 300 4MATIC Sport

Overall vehicle length Overall vehicle width36
Overall vehicle height

Wheelbase Track, front

Track, rear

Turning circle

182.3 in (4 630 mm)

79.2 in (2 012 mm)

57.0 in (1 449 mm)37
56.9 in (1 445 mm)38
108.7 in (2 760 mm) 60.4 in (1 533 mm)37
60.7 in (1 541 mm)38
60.5 in (1 536 mm)37
60.8 in (1 544 mm)38
35.4 ft (10.8 m)

Weights C 300 4MATIC

Roof load Trunk load

max. 220 lb (100 kg) max. 220 lb (100 kg)

Vehicle specification C 300 4MATIC Sport (204.081)

The quoted data apply only to the standard vehicle. Contact an authorized Mercedes- Benz Center for the corresponding data of all special bodies and special equipment. i The C 300 4MATIC Sport is available in

the USA only.

Engine C 300 4MATIC Sport

Engine, type Mode of operation

272

4-stroke engine, gasoline injection

No. of cylinders Bore Stroke Total piston displacement Compression ratio Output acc. to SAE J 134939
Maximum torque acc. to SAE J 1349

3.46 in (88.00 mm) 3.23 in (82.10 mm)

182.8 cu in (2 996 cm3)

11.3:1

228 hp/6 000 rpm (170 kW/6 000 rpm)

221 lb-ft/

2 500 - 5 000 rpm

(300 Nm/

2 500 - 5 000 rpm)

Maximum engine speed Firing order Poly-V-belt

6 500 rpm

1-4-3-6-2-5
2 401 mm

14 V/150 A 12 V/1.4 kW 12 V/74 Ah

Electrical system C 300 4MATIC Sport Alternator Starter motor Battery Spark plugs, type Spark plugs, electrode gap Spark plugs, tightening torque

Bosch Y 7 MPP33
0.031 in (0.8 mm)

15 - 18 lb-ft (20 - 25 Nm)

36 Exterior rear view mirrors folded out. 37 Canada only. 38 USA only. 39 Premium fuel required. Performance may vary with fuel octane rating.

204_AKB; 5; 23, en-US d2ureepe,

2009-07-16T17:54:06+02:00 - Seite 341
Version: 2.11.8.1

Vehicle specification C 350 (204.056)

341

79.2 in (2 012 mm)

Main dimensions C 300 4MATIC Sport Overall vehicle 182.3 in (4 630 mm) length Overall vehicle width40
Overall vehicle height Wheelbase Track, front Track, rear Turning circle

108.7 in (2 760 mm) 60.4 in (1 533 mm) 60.5 in (1 536 mm) 35.4 ft (10.8 m)

57.0 in (1 449 mm)

Weights C 300 4MATIC Sport

Roof load Trunk load

max. 220 lb (100 kg) max. 220 lb (100 kg)

Vehicle specification C 350 (204.056)

The quoted data apply only to the standard vehicle. Contact an authorized Mercedes- Benz Center for the corresponding data of all special bodies and special equipment. i The C 350 is available in Canada only.

Engine C 350

Engine, type Mode of operation

No. of cylinders Bore Stroke Total piston displacement

272

4-stroke engine, gasoline injection

3.66 in (92.90 mm) 3.39 in (86.00 mm)

213.5 cu in (3 498 cm3)

Engine C 350

Compression ratio Output acc. to SAE J 134941
Maximum torque acc. to SAE J 1349

10.7:1

268 hp/6 000 rpm (200 kW/6 000 rpm)

258 lb-ft/

2 400 - 5 000 rpm

(350 Nm/

2 400 - 5 000 rpm)

Maximum engine speed Firing order Poly-V-belt

6 500 rpm

1-4-3-6-2-5
2 401 mm

Electrical system C 350

Alternator Starter motor Battery Spark plugs, type Spark plugs, electrode gap Spark plugs, tightening torque

14 V/150 A 12 V/1.4 kW 12 V/74 Ah

Bosch Y 7 MPP33
0.031 in (0.8 mm)

15 - 18 lb-ft (20 - 25 Nm)

Main dimensions C 350

Overall vehicle length Overall vehicle width42
Overall vehicle height Wheelbase

182.3 in (4 630 mm)

79.2 in (2 012 mm)

57.0 in (1 449 mm)

108.7 in (2 760 mm)

40 Exterior rear view mirrors folded out. 41 Premium fuel required. Performance may vary with fuel octane rating. 42 Exterior rear view mirrors folded out.

204_AKB; 5; 23, en-US d2ureepe,

2009-07-16T17:54:06+02:00 - Seite 342
Version: 2.11.8.1

342 Vehicle specification C 350 Sport (204.056)

Main dimensions C 350

Engine C 350 Sport

Track, front Track, rear Turning circle

60.4 in (1 533 mm) 60.5 in (1 536 mm) 35.4 ft (10.8 m)

Weights C 350

Roof load Trunk load

max. 220 lb (100 kg) max. 220 lb (100 kg)

Vehicle specification C 350 Sport (204.056)

The quoted data apply only to the standard vehicle. Contact an authorized Mercedes- Benz Center for the corresponding data of all special bodies and special equipment. i The C 350 Sport is available in the USA

only.

Engine C 350 Sport

Engine, type Mode of operation

No. of cylinders Bore Stroke Total piston displacement Compression ratio Output acc. to SAE J 134943

272

4-stroke engine, gasoline injection

3.66 in (92.90 mm) 3.39 in (86.00 mm)

213.5 cu in (3 498 cm3)

10.7:1

268 hp/6 000 rpm (200 kW/6 000 rpm)

Maximum torque acc. to SAE J 1349

258 lb-ft/

2 400 - 5 000 rpm

(350 Nm/

2 400 - 5 000 rpm)

Maximum engine speed Firing order Poly-V-belt

6 500 rpm

1-4-3-6-2-5
2 401 mm

Electrical system C 350 Sport 14 V/150 A 12 V/1.4 kW 12 V/74 Ah

Alternator Starter motor Battery Spark plugs, type Spark plugs, electrode gap Spark plugs, tightening torque

Bosch Y 7 MPP33
0.031 in (0.8 mm)

15 - 18 lb-ft (20 - 25 Nm)

Main dimensions C 350 Sport

Overall vehicle length Overall vehicle width44
Overall vehicle height Wheelbase Track, front Track, rear Turning circle

182.8 in (4 630 mm)

79.2 in (2 012 mm)

57.0 in (1 449 mm)

108.7 in (2 760 mm) 60.4 in (1 533 mm) 60.5 in (1 536 mm) 35.4 ft (10.8 m)

43 Premium fuel required. Performance may vary with fuel octane rating. 44 Exterior rear view mirrors folded out.

204_AKB; 5; 23, en-US d2ureepe,

2009-07-16T17:54:06+02:00 - Seite 343
Version: 2.11.8.1

Vehicle specification C 63 AMG (204.077)

343

Weights C 350 Sport

Roof load Trunk load

max. 220 lb (100 kg) max. 220 lb (100 kg)

Vehicle specification C 350 4MATIC (204.087)

The quoted data apply only to the standard vehicle. Contact an authorized Mercedes- Benz Center for the corresponding data of all special bodies and special equipment. i The C 350 4MATIC is available in Canada

only.

Engine C 350 4MATIC 272

Engine, type Mode of operation

No. of cylinders Bore Stroke Total piston displacement Compression ratio Output acc. to SAE J 134945
Maximum torque acc. to SAE J 1349

4-stroke engine, gasoline injection

3.66 in (92.90 mm) 3.39 in (86.00 mm)

213.5 cu in (3 498 cm3)

10.7:1

268 hp/6 000 rpm (200 kW/6 000 rpm)

258 lb-ft/

2 400 - 5 000 rpm

(350 Nm/

2 400 - 5 000 rpm)

Maximum engine speed Firing order Poly-V-belt

6 500 rpm

1-4-3-6-2-5
2 401 mm

Electrical system C 350 4MATIC 14 V/150 A 12 V/1.4 kW 12 V/74 Ah

Alternator Starter motor Battery Spark plugs, type Spark plugs, electrode gap Spark plugs, tightening torque

Bosch Y 7 MPP33
0.031 in (0.8 mm)

15 - 18 lb-ft (20 - 25 Nm)

Main dimensions C 350 4MATIC

Overall vehicle length Overall vehicle width46
Overall vehicle height Wheelbase Track, front Track, rear Turning circle

182.3 in (4 630 mm)

79.2 in (2 012 mm)

57.0 in (1 449 mm)

108.7 in (2 760 mm) 60.4 in (1 533 mm) 60.5 in (1 536 mm) 35.4 ft (10.8 m)

Weights C 350 4MATIC

Roof load Trunk load

max. 220 lb (100 kg) max. 220 lb (100 kg)

Vehicle specification C 63 AMG (204.077)

The quoted data apply only to the standard vehicle. Contact an authorized Mercedes- Benz Center for the corresponding data of all special bodies and special equipment.

45 Premium fuel required. Performance may vary with fuel octane rating. 46 Exterior rear view mirrors folded out.

204_AKB; 5; 23, en-US d2ureepe,

344 Rims and tires

2009-07-16T17:54:06+02:00 - Seite 344
Version: 2.11.8.1

Engine C 63 AMG

Main dimensions C 63 AMG

Engine, type Mode of operation

No. of cylinders Bore Stroke Total piston displacement Compression ratio Output acc. to SAE J 134947
Maximum torque acc. to SAE J 1349
Maximum engine speed Firing order Poly-V-belt

156

4-stroke engine, gasoline injection

4.02 in (102.20 mm) 3.72 in (94.60 mm)

378.8 cu in (6 208 cm3)

11.3:1

450 hp/6 800 rpm (336 kW/6 800 rpm) 443 lb-ft/5 000 rpm (600 Nm/5 000 rpm)