2002 Mercedes-benz C Class Coupe Owners Manual

getting out of the vehicle. The night security illumination will not be activated when the door is opened.

Headlamp cleaning system (optional)

Locator lighting After unlocking the vehicle with the electronic key during darkness the fog lamps and parking lamps switch on for approximately 40 seconds. The exterior lamps will be switched off when opening the driver’s door. See the individual setting menu “LIGHTING” – “LOCATOR LIGHTING” on page 128, for instructions on how to activate the function.

P82.10-2780-26

Turn the electronic key in starter switch to position 2. The headlamps will be cleaned with a high-pressure water jet when you press the headlamp washer button (1). See page 320 for instructions on filling up the windshield/headlamp washer reservoir.

Exterior lamp switch

147

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Combination switch

148

Combination switch

1 Low beam

(exterior lamp switch position B)

2 High beam

(exterior lamp switch position B)

3 High beam flasher (high beam available

independent of exterior lamp switch position)

4 Turn signals, right 5 Turn signals, left

To signal minor directional changes, such as changing lanes on a highway, move combination switch briefly to the point of resistance only and release. The turn signals blink three times. To operate the turn signals continuously, move the combination switch past the point of resistance (up or down). The switch is automatically canceled when the steering wheel is turned to a large enough degree.

Turn signal failure If one of the turn signals fails, the turn signal indicator system flashes and sounds at a faster than normal rate.

I

Intermittent wiping Vehicles with optional rain sensor: One initial wipe, pauses between wipes are automatically controlled by a rain sensor monitoring the wetness of the windshield. This will not occur with a door open.

Notes: With switch in this position, one wipe occurs when turning the electronic key in starter switch from position 0. However, this might cause scratches in a dry windshield. Turn combination switch to Off position before turning the electronic key in starter switch from position 0. Do not leave in intermittent setting when vehicle is taken to an automatic car wash or during windshield cleaning. Wipers will operate in presence of water spray at windshield, and wipers may be damaged as a result.

II Normal wiper speed III Fast wiper speed

Vehicles without optional rain sensor: If the vehicle is standing still, the wiper will switch back one setting.

6 Press switch briefly:

Single wipe without washer fluid (select only if windshield is wet). Push switch past resistance point: Windshield washer system, windshield wipers. See page 320 for instructions on filling the windshield washer reservoir.

7 Windshield wipers

0 Off

Combination switch

149

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Combination switch

150

Blocked windshield wipers If the windshield wipers become blocked (for example, due to snow), switch off the wipers. For safety reasons before removing ice or snow, remove electronic key from starter switch. Remove blockage. Activate combination switch again (electronic key in starter switch position 1).

Emergency operation of windshield wipers In case of windshield wiper malfunction in switch positions I or III, turn combination switch to wiper setting II. Have the system checked at your authorized Mercedes-Benz Center as soon as possible.

Windshield wipers smear If the windshield wipers smear the windshield, even during rain, activate the washer system as often as necessary. The fluid in the washer reservoir should be mixed in the correct ratio. See page 320 for instructions on filling up the windshield washer reservoir. See page 356 for instructions on replacing wiper blade inserts.

Windshield and headlamp washer fluid mixing ratio For temperatures above freezing: MB Windshield Washer Concentrate “S” and water. 1 part “S” to 100 parts water (40 ml “S” to 1 gallon water). For temperature below freezing: MB Windshield Washer Concentrate “S” and commercially available premixed windshield washer solvent/antifreeze 1 part “S” to 100 parts solvent (40 ml “S” to 1 gallon solvent).

Hazard warning flasher switch

To activate hazard warning flasher, press switch once. To deactivate, press switch again.

Note: With the hazard warning flasher activated, the combination switch in position for either left or right turn, and the electronic key in starter switch position 1 or 2, only the respective left or right side turn signals will operate. After turn signal cancellation, the hazard warning flasher is activated.

The hazard warning flasher can be activated either manually via the switch located in the dashboard, or it is activated automatically at the time an airbag is deployed.

Hazard warning flasher

151

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Instruments and controls

Climate control

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

152

Climate control

P83.20-2150-29

1 Display and controls 2 Air volume control for left center air outlet 3 Center air outlet, left, adjustable 4 Thumbwheel for adding outside air at air outlets for center, left and right sides, as well as dashboard top center and rear passenger compartment

5 Center air outlet, right, adjustable

6 Air volume control for right center air outlet 7 Air volume control and air outlet on dashboard top

center

8 Air volume control for side air outlet 9 Side air outlet, adjustable 10 Side defroster outlet, fixed

Climate control

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

153

Instruments and controls

Climate control

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

154

5 Rear window defroster, see page 170
6 Economy mode, see page 159

Residual engine heat utilization, see page 159

7 Air distribution and air volume (automatic) 8 Air recirculation, see page 167
9 Defrosting, see page 157

Important! This vehicle is equipped with an air conditioning system that uses R-134a (HFC: hydrofluorocarbon) as a refrigerant. Repairs should always be performed by a qualified technician, and refrigerant should be collected in a recovery system for recycling.

Display and controls

1 Air volume 2 Temperature control, left 3 Temperature control, right 4 Air distribution control switch

Climate control The system is always at operational readiness, except when manually switched off. The climate control only operates with the engine running. The temperature selector should be left at the desired temperature setting. The temperature selected is reached as quickly as possible. The system will not heat or cool any quicker by setting a higher or lower temperature. The desired interior temperature can be selected separately for the left and right side of the passenger compartment. Adjust the temperature settings in small increments. The climate control removes considerable moisture from the air during operation in the cooling mode. It is normal for water to drip on the ground through ducts in the underbody. The air conditioning will not engage (no cooling) if the economy mode S is selected, see page 159.

Notes: Do not obstruct the air flow by placing objects on the air flow-through exhaust slots below the rear window. Also keep the air intake grill in front of the windshield free of snow and debris. The storage compartment between the front seats can be ventilated. See page 171 for notes on ventilating the storage space under the armrest in the center console. The air conditioner switches itself off for its own protection if refrigerant is lost. No cooling will then take place. Economy mode S cannot be switched off. Have the air conditioner checked by a Mercedes-Benz Center should this happen. If the vehicle interior has been heated by direct sunlight and is very hot, ventilate the interior (open door or windows for a short period) before driving off.

Dust filter Nearly all dust particles and pollen are filtered out before outside air enters the passenger compartment through the air distribution system.

Climate control

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

155

Instruments and controls

Climate control

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Basic setting – automatic mode In the automatic mode the climate control cools or heats the interior depending on outside temperature and the selected interior temperature. With the automatic mode switched off, the air volume and distribution can still be set manually.

Press U button. Air volume and distribution are controlled automatically.

We recommend to set the left and right temperature to 72°F (22°C). Please make changes from this setting to suit your personal requirements.

Heating mode: To lower headroom temperature, use thumbwheel (4, page 152).

Air conditioning mode: Open air outlets at dashboard top center (7, page 152) for an even air distribution.

156

Special settings (use only for short duration)

Air distribution and air volume, manual Press U button. The indicator lamp in the button will go out. The air distribution for the right and left side operate together. Select any of the six air volume speeds and the air distribution.

Air distribution, manual: h Air from the center, side, dashboard top center

and rear passenger compartment air outlets.

j Air from the windshield, side defroster and rear

passenger compartment air outlets.

k Air from the center, side, footwell, rear footwell

and rear passenger compartment air outlets.

To return to automatic mode: Press the U button. The indicator lamp in the button illuminates.

Defrosting

Press the P button. The indicator lamp in the button illuminates. Switch off air recirculation, if selected. Press button O, the indicator lamp in the button will go out. Close center air outlets. Turn wheels (8, page 152) up to open left and right side air outlets (9, page 152). Adjust side air outlets upward. Pressing the switch again returns the system to the previous setting.

Windows fogged up on the inside Switch off the economy mode, if selected. Press button S. The indicator lamp in the button will go out. Switch off air recirculation, if selected. Press button O. The indicator lamp in the button will go out. Set blower to the maximum blower speed. Press the P button. The indicator lamp in the button illuminates. Increase temperature setting. Open the side air outlets (9, page 152) and direct them onto the side windows.

Windshield fogged up on the outside Switch on the windshield wiper. Close air outlet at dashboard top center. Switch to manual mode. Turn air distribution control switch to position h or k.

Climate control

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

157

Instruments and controls

Climate control

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Air recirculation Select air recirculation: The indicator lamp in the O button is not illuminated. Press button O briefly. The indicator lamp in the button illuminates. To switch off the air recirculation: The indicator lamp in the O button is illuminated. Press button O briefly. The indicator lamp in the button goes out. Switching on air recirculation and activating convenience closing of power windows: The indicator lamp in the O button is not illuminated. Press button O for more than 2 seconds, the side windows will be closed. The indicator lamp in the button illuminates.

158

Switching off air recirculation and activating convenience opening: The indicator lamp in the O button is illuminated. Press button O for more than 2 seconds, the side windows return to the position they were in before closing. A window opened manually after convenience closing will no longer be returned to the position it was in before closing when convenience opening is selected. The system automatically switches from air recirculation to fresh air: • after 30 minutes if the outside temperature is above

about 40°F (5°C),

• after 5 minutes if the outside temperature is below

about 40°F (5°C),

• after 5 minutes if economy mode S is selected. The system switches automatically to air recirculation at high outside temperatures. A quantity of outside air is added after a maximum of 30 minutes. If the windows should fog up from the inside, switch from recirculated air back to fresh air.

Economy mode The function of this setting corresponds to the automatic mode. However, because the air conditioning compressor will not engage (fuel savings), it is not possible to air condition in this setting. Press S button to activate. The indicator lamp in the button illuminates. Press S button once again to return to the previous setting. The indicator lamp in the button goes out.

Important! In the S mode the windows could fog up on the inside. Switch off S mode.

Climate control - OFF/ON To switch the climate control off, set the air volume control switch to position 0. The fresh air supply to the vehicle interior is shut off. While driving, use this setting only temporarily, otherwise the windshield could fog up. To switch the climate control on again, or set air volume control switch to any speed.

Residual engine heat utilization With the engine switched off, it is possible to continue to heat or ventilate the interior for a short while, dependent of the temperature setting of the automatic climate control. Air volume and distribution are controlled automatically. To select: Turn the electronic key in starter switch to position 1 or 0 or remove it altogether. Press button T. The indicator lamp in the button illuminates. This function selection will not activate if the battery level is insufficient. The function switches off automatically: • if the electronic key in starter switch is turned to

position 2,

• after approximately 30 minutes, • if the battery voltage drops.

Climate control

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

159

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Automatic climate control

160

Automatic climate control (optional)

P83.20-2150-29

1 Display and controls 2 Air volume control for left center air outlet 3 Center air outlet, left, adjustable 4 Thumbwheel for adding outside air at air outlets for center, left and right sides, as well as dashboard top center and rear passenger compartment

5 Center air outlet, right, adjustable

6 Air volume control for right center air outlet 7 Air volume control and air outlet on dashboard top

center

8 Air volume control for side air outlet 9 Side air outlet, adjustable 10 Side defroster outlet, fixed

Automatic climate control

161

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Automatic climate control

162

Display and controls

7 Temperature control, right, raising 8 Temperature control, right, lowering 9 Rear window defroster, see page 170
10 Economy mode, see page 169

Residual engine heat utilization, see page 169

11 Air volume control +

switch on system

12 Air volume control -

switch off system

P83.40-2303-26

13 Air recirculation, see page 167
14 Defrosting, see page 166

1 Temperature control, left, lowering 2 Temperature control, left, raising 3 Air distribution control switch left (automatic,

manual operation)

4 Activated charcoal filter, see page 168
5 Display 6 Air distribution control switch right (automatic,

manual operation)

Important! This vehicle is equipped with an air conditioning system that uses R-134a (HFC: hydrofluorocarbon) as a refrigerant. Repairs should always be performed by a qualified technician, and refrigerant should be collected in a recovery system for recycling.

1 Temperature, left 2 Temperature, right 3 Air volume 4 Automatic mode is selected

Automatic climate control The system is always at operational readiness, except when manually switched off. The automatic climate control only operates with the engine running. The temperature selector should be left at the desired temperature setting. The temperature selected is reached as quickly as possible. The system will not heat or cool any quicker by setting a higher or lower temperature. The desired interior temperature and air distribution can be selected separately for the left and right side of the passenger compartment. Adjust the temperature settings in small increments. The automatic climate control removes considerable moisture from the air during operation in the cooling mode. It is normal for water to drip on the ground through ducts in the underbody. The air conditioning will not engage (no cooling) if the economy mode S is selected, see page 169.

Automatic climate control

163

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Automatic climate control

164

Notes: Do not obstruct the air flow by placing objects on the air flow-through exhaust slots below the rear window. Also keep the air intake grill in front of the windshield free of snow and debris. The storage compartment between the front seats can be ventilated. See page 171 for notes on ventilating the storage space under the armrest in the center console. The air conditioner switches itself off for its own protection if refrigerant is lost. No cooling will then take place. Economy mode S cannot be switched off. Have the air conditioner checked by a Mercedes-Benz Center should this happen. If the vehicle interior has been heated by direct sunlight and is very hot, ventilate the interior (open door or windows for a short period) before driving off.

Dust filter Nearly all dust particles and pollen are filtered out before outside air enters the passenger compartment through the air distribution system.

Basic setting – automatic mode In the automatic mode the automatic climate control cools or heats the interior depending on the direction and strength of the sunlight, outside temperature and the selected interior temperature of the vehicle. With the automatic mode switched off, the air volume and distribution can still be set manually. Briefly press left or right U button. The h, j and k symbols will no longer be visible. The economy mode and air recirculation functions will be switched off. The automatic blower will be activated at the same time. We recommend to set the temperature switches on the left and right to 72°F (22°C). Please make changes from this setting to suit your personal requirements.

Heating mode: To lower headroom temperature, use thumbwheel (4, page 160).

Air conditioning mode: Open air outlets at dashboard top center (7, page 160) for an even air distribution.

Special settings (use only for short duration)

Air distribution, manual Press left or right U button. The button pops out, the h, j and k symbols are visible. Turn the button to select the air distribution desired. h Air from the center, side, dashboard top center

and rear passenger compartment air outlets.

j Air from the windshield, side defroster and rear

passenger compartment air outlets.

k Air from the center, side, footwell, rear footwell

and rear passenger compartment air outlets.

To return to automatic mode: Press left or right U button. The h, j and k symbols will no longer be visible.

Air volume, manual Seven blower speeds are available. Press right Q or left M side of air volume control switch until the requested blower speed is attained. The display “AUTO” disappears and the automatic mode is switched off. The selected blower speed is shown in the display.

To return to automatic mode: Press left or right U button until it clicks in. The h, j and k symbols will no longer be visible.

Automatic climate control

165

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Automatic climate control

166

Defrosting Press the P button. The indicator lamp in the button illuminates. Maximum heated and automatically controlled amount of air is directed to the defroster and windshield air outlets. Switch off air recirculation, if selected: Press button O. The indicator lamp in the button will go out. Pressing the P button again returns the system to the previous setting.

Windows fogged up on the inside Switch off the economy mode, if selected: Press button S. The indicator lamp in the button will go out. Switch off air recirculation, if selected: Press button O. The indicator lamp in the button will go out. Set blower to the maximum blower speed. Increase temperature setting. Open the side air outlets and direct them onto the side windows.

Windshield fogged up on the outside Switch on the windshield wiper. Close air outlet at dashboard top center (7, page 161). Switch to manual mode. Turn air distribution control switch to position h or k.

Air recirculation Select air recirculation: The indicator lamp in the button O is not illuminated. Press button O briefly. The indicator lamp in the button illuminates. To switch off the air recirculation: The indicator lamp in the button O is illuminated. Press button O briefly. The indicator lamp in the button goes out. Switching on air recirculation and activating convenience closing of power windows: The indicator lamp in the button O is not illuminated. Press button O for more than 2 seconds, the side windows will be closed. The indicator lamp in the button illuminates.

Switching off air recirculation and activating convenience opening: The indicator lamp in the button O is illuminated. Press button O for more than 2 seconds, the side windows return to the position they were in before closing. A window opened manually after convenience closing will no longer be returned to the position it was in before closing when convenience opening is selected. The system automatically switches from air recirculation to fresh air: • after 30 minutes if the outside temperature is above

about 40°F (5°C),

• after 5 minutes if the outside temperature is below

about 40°F (5°C),

• after 5 minutes if economy mode S is selected. The system switches automatically to air recirculation at high outside temperatures. A quantity of outside air is added after a maximum of 30 minutes. If the windows should fog up from the inside, switch from recirculated air back to fresh air.

Automatic climate control

167

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Automatic climate control

168

Activated charcoal filter An activated charcoal filter markedly reduces bad odors and removes pollutants from air entering the passenger compartment. Select activated charcoal filter: The indicator lamp in the button e is not illuminated. Press e button briefly. The indicator lamp in the button illuminates. Switch off activated charcoal filter: The indicator lamp in the button e is illuminated. Press e briefly. The indicator lamp in the button goes out. The system switches automatically to the air recirculation mode, if the carbon monoxide (CO) or nitrogen oxides (NOX) concentration of the outside air increases beyond a predetermined level. The automatic air recirculation mode does not function if economy mode S is selected or if the outside temperature has fallen below 40°F (5°C).

The activated charcoal filter should be switched off when windows fog up on the inside, or if the passenger compartment needs to be quickly heated or cooled down. Switching on the activated charcoal filter and activating convenience closing of power windows: The indicator lamp in the e button is not illuminated. Press button e for more than 2 seconds, the side windows will be closed. The indicator lamp in the button illuminates. Switching off activated charcoal filter and activating convenience opening: The indicator lamp in the e button is illuminated. Press button e for more than 2 seconds, the side windows return to the position they were in before closing. The indicator lamp in the button goes out. A window opened manually after convenience closing will no longer be returned to the position it was in before closing when convenience opening is selected.

Economy mode The function of this setting corresponds to the automatic mode. However, because the air conditioning compressor will not engage (fuel savings), it is not possible to air condition in this setting. Press S button to activate. The indicator lamp in the button illuminates. Press S button once again to return to the previous setting. The indicator lamp in the button goes out.

Important! In the S mode the windows could fog up on the inside. Switch off S mode.

Automatic climate control - OFF/ON To switch the automatic climate control off, set the air volume control switch to position 0. The fresh air supply to the vehicle interior is shut off. While driving, use this setting only temporarily, otherwise the windshield could fog up.

To switch the automatic climate control on again, press the U or P button, or set air volume control switch to any speed.

Residual engine heat utilization With the engine switched off, it is possible to continue to heat or ventilate the interior for a short while, dependent of the temperature set in the automatic climate control. Air volume and distribution are controlled automatically. To select: Turn the electronic key in starter switch to position 1 or 0 or remove it altogether. Press button T. The indicator lamp in the button illuminates. This function selection will not activate if the battery level is insufficient. The function switches off automatically: • if the electronic key in starter switch is turned to

position 2,

• after approximately 30 minutes, • if the battery voltage drops.

Automatic climate control

169

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Automatic climate control

170

Rear window defroster Turn the electronic key in starter switch to position 2.

To select: Press the F button in the control panel of the automatic air conditioner. The indicator lamp in the button illuminates.

To cancel: Press the F button in the control panel of the automatic air conditioner. The indicator lamp in the button goes out.

Note: Heavy accumulation of snow and ice should be removed before activating the defroster.

The rear window defroster uses a large amount of power. To keep the battery drain to a minimum, turn off the defroster as soon as the rear window is clear. The defroster is automatically turned off after approximately 6–17 minutes of operation depending on the outside temperature and vehicle speed. If several power consumers are turned on simultaneously, or the battery is only partially charged, it is possible that the defroster will automatically turn itself off. When this happens, the indicator lamp inside the switch starts blinking. As soon as the battery has sufficient voltage, the defroster automatically turns itself back on.

Front center console storage compartment ventilation

The front center console compartment has its own air outlet. To open: Raise lever (1). To close: Lower lever (1).

The air volume is dependent on the setting of: • air distribution control, • air volume control, • air outlets in the dashboard. The air temperature is about the same as that of the dashboard air outlets. It cannot be regulated separately.

Notes: The compartment can get very warm due to its confined space. When storing heat sensitive objects in the compartment, close the air outlet while heating the passenger compartment. Do not allow articles to obstruct the air outlet in the storage compartment.

Automatic climate control

171

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Automatic climate control

172

Rear passenger compartment adjustable air outlets

1 Center air outlet, left 2 Air volume control for center air outlets

To open: Turn the wheel upward.

3 Center air outlet, right

Note: The temperature at the air outlets for the rear passenger compartment (1 and 3) is the same as at the dashboard center air outlets.

Audio and telephone operation These instructions are intended to help you become acquainted with your Mercedes-Benz audio system. They contain useful tips and a detailed description of the user functions.

Warning! In order to avoid distraction which could lead to an accident, system settings should be entered with the vehicle at standstill and systems should be operated by the driver only when traffic conditions permit. Always pay full attention to traffic conditions first before operating system controls while driving. Bear in mind that at a speed of just 30 mph (approximately 50 km/h), your car is covering a distance of 50 feet (approximately14 m) every second.

Operating safety

Warning! Any alterations made to electronic components can cause malfunctions. The radio, cassette deck, CD changer1 and telephone1 are interconnected. Therefore, when one of the components is defective or has not been removed/replaced properly this may impair the function of other components. These malfunctions might seriously impair the operating safety of your vehicle. We recommend that you have any service work or alterations to electronic components done at an authorized Mercedes-Benz Center.

1 Optional equipment

Dolby and the double-D symbol Ù are trademarks of Dolby Laboratories Licensing Corporation. The Dolby noise reduction system is manufactured under licence from Dolby Laboratories Licensing Corporation.

Audio system

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

173

Instruments and controls

Audio system

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

174

Operating and display elements

1 On/off, volume, see page 176
2 Telephone mode selector, see page 190
3 Seek tuning, see page 180,

Track search (tape), see page 184, Skipping tracks (CD), see page 188
Manual repeat dialing (telephone), see page 193

4 Radio mode selector, see page 179
5 Manual tuning, see page 180 and 180

Fast Forward/Reverse (tape), see page 184
Fast Forward/Reverse (CD), see page 189
Telephone book, see page 191

6 CD mode selector, see page 188
7 Tape mode selector, see page 182

8 Display panel

The cassette slot is located behind the display panel. For notes on playing cassettes, see page 182

9 Alpha-numeric keypad for

station storage and frequency entry, see page 182
optional telephone, see page 190
Tape eject, see page 183
Tape track select, see page 184
Dolby, see page 185
CD track access, see page 190

10 Scan tuning (Radio, see page 180)

Tape track search, see page 184
CD, see page 180

11 Function button, see page 182 and 190
12 Soft keys for

radio band selection, see page 179
tone controls, see page 177
scan, see page 180

13 Tape eject, see page 182

Audio system

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

175

Instruments and controls

Audio system

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Button and soft key operation In these instructions, the alpha-numeric keypad (right side of radio face) and the function buttons (left side of the radio face) are referred to as “buttons” and the four keys under the display are referred to as “soft keys”

Note: Do not press directly on the radio display face.

176

Operation

Switching on and off Press the control knob The system is switched off when the electronic key in the starter switch is turned to position 0 or removed. The radio is switched on again when the electronic key in the starter switch is turned to position 1 or 2.

Note: The system can also be switched on separately with the electronic key removed, but will switch itself off automatically after half an hour to conserve vehicle battery power.

Adjusting the volume Turning the control knob clockwise will increase the volume, counterclockwise will decrease the volume.

Bass

Note: The volume setting can be selected separately for the telephone, audio system and voice recognition system.

Audio functions The “AUD” key is used to select the BASS, TREBLE, FADER and BALANCE functions. Settings for bass and treble are stored separately for the radio, cassette and CD modes. Tone level settings are identified by the vertical bars. The center (flat) setting is shown by one longer bar in the center of the display.

Press the “AUD” key repeatedly until “BASS” appears on the display. Press the “+” key to increase

or the “-” key to decrease the level. Pressing the “+” and “-” keys simultaneously resets the Bass to its center (flat) level.

Treble

Press the “AUD” key repeatedly until “TREBLE” appears on the display. Press the “+” key to increase

or the “-” key to decrease the level. Pressing the “+” and “-” keys simultaneously resets the Treble to its center (flat) level.

Audio system

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

177

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Instruments and controls

Audio system

Fader

178

Centering all audio functions

Push and hold down the “AUD” key. All audio functions (bass, treble, balance and fader) are set to center or flat positions, and

the volume is adjusted to a preset level. “RESET” appears on the display.

Press the “AUD” key repeatedly until “FADER” appears on the display. Press the “R” key to move the sound to the rear speakers or the “F”

key to move the sound to the front speakers. Pressing the “F” and “R” keys simultaneously resets the Fader to its center level.

Balance

Press the “AUD” key repeatedly until “BALANCE” appears on the display. Press the “L” key to move the

sound to the left speakers or the “R” key to move the sound to the right speakers. Pressing the “L” and “R” keys simultaneously resets the Balance to its center level.

Audio system tone level selection

Radio mode

To select the tone level settings for radio, cassette, and CD operation press the key “AUD”. The tone level settings menu is now

displayed. Press key “EXT”, and “SOUND” appears on the display. Press the key “DRV” to adjust the sound to the driver and co-driver position. The key “SP” is for “Speech”, optimizing the sound for spoken language. The key “AMB” offers “Ambience”, a three-dimensional sound. The key “OFF” switches off the tone level setting selection.

Selecting radio mode Press

button.

Selecting the band

Frequency ranges:

Press the key located below the desired band. The band selected is shown in the top line of the display.

FM AM WB

87.9 -107.9 MHz 530 -1710 kHz approx.162 MHz

Audio system

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

179

Instruments and controls

Audio system

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

180

Manual tuning

or

Press either the button. Step-by-step station tuning in ascending or descending order of frequency will take place. The first three tuning steps will take place without muting. The radio will then be muted and high-speed tuning will take place until the button is released. The following tuning intervals will be shown on the display:

FM AM WB

200 kHz 10 kHz Channels 1-7

Seek tuning Press either the to the next receivable station.

or

button. The radio will tune

Scan tuning

SC #

button. Each

Press the strongly receivable station on the band selected will be tuned in for 8 seconds. The first scan will tune only the stations with a high signal strength. The second scan will tune every receivable station. By pressing either the

buttons or the

SC #

button the

scan mode can be cancelled.

Weather Band Press the “WB” key. The last weather band station is tuned in. Use buttons the station cannot be received, the next available station is selected automatically. Press button . The next available station is tuned in. The message “WB NONE” appears if no station can be received.

to select a different station. If

or

PQRS

Station memory Ten stations each in the AM and FM bands can be stored via the alpha-numeric keypad. The button corresponds to location 10. Weatherband (WB) channels 1 to 7 are preset at the factory and can be retrieved via the alpha-numeric keypad, but cannot be changed.

OPR

Storing stations automatically (Autostore)

Press the “AS” key until the word “SEARCH” is displayed. The ten strongest stations are stored automatically, with having the strongest

signal.

If less than 10 stations are available within receiving range, only those will be stored. Pressing a station selection button without a stored station will not display a frequency for approximately 2 seconds. Thereafter the station selected last will be displayed.

Note: Autostore memory is in addition to the regular station memory. Previously stored stations are not erased. Briefly press “AS” to leave the Autostore and return to manual presets. Press “AS” again to call up Autostore.

Audio system

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

181

Instruments and controls

Audio system

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Storing stations Hold the desired number button approximately 2 seconds. The currently displayed frequency is stored on the selected station button. The storage procedure is confirmed by a short signal tone.

down for

OPR

Retrieving a station from memory Press the desired station button

OPR

Direct frequency input (AM and FM only)

Select the band. Press the “ button and enter the desired frequency using the alpha-numeric keypad . Frequencies outside of

OPR

the frequency ranges (frequencies specified on page 179) will not be accepted. The frequency input mode is cancelled if no button is pressed within 4 seconds.

182

Cassette mode

TAPE

Playing cassettes Press the the display folds down and the cassette slot becomes visible. Push the cassette gently into the slot until it engages. The cassette will be pulled in automatically.

button. When the

button is pressed,

EJ

Note: Do not press directly on the display face. Return the display panel to its normal position by folding it back up and pressing gently on the display frame to lock in place.

Important! If the display is in the down position for more than 20 seconds, 2 successive beeps will be heard. This will continue at 5 second intervals until the display is returned to its normal position.

The system will switch to cassette mode. Track 1 will be played and “SIDE 1” displayed. Track 1 is the side of the cassette which is facing upwards. The cassette deck will automatically detect the type of tape and switch the equalization automatically. A cassette symbol on the display indicates that a tape is in the mechanism. This symbol appears in all modes except cassette mode. The cassette will not be ejected when the system is switched off or another mode is selected. If a cassette is in the mechanism, cassette mode can be selected by using the If no cassette has been inserted, the display will show “NO TAPE”.

button.

TAPE

EJ

Cassette eject Press the button. The display will fold down and the cassette will be ejected. Remove the cassette, then fold the display back up manually. The system will switch back to radio mode automatically.

Notes: The cassette will not be ejected when the system is switched off. If a cassette is not ejected, continue to hold the EJ cassette.

button for at least 5 seconds to eject the

Important! If the display is in the down position for more than 20 seconds, 2 successive beeps will be heard. This will continue at 5 second intervals until the display is returned to its normal position.

Audio system

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

183

Instruments and controls

Audio system

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Track selection

Press the track selection “TRK” key. The current track will be displayed as “SIDE 1” or “SIDE 2”. The track will be changed automatically at the end of the tape.

Track search forward/backward

button.

Press the “SEEK FWD” will be shown on the display and the track search will run the tape forward to the start of the next track. Press the “SEEK RWD” will be shown on the display and the track search will run the tape backward to the start of the

button.

track currently playing. Track search can be interrupted by pressing the same button again.

184

Note: The beginning of a track can only be located if there is a break of at least 4 seconds between tracks.

Fast forward/reverse

button.

Press the “FORWARD” will appear on the display and fast forward will start. Press the “REWIND” will appear on the display and fast reverse will start.

button.

Fast forward/reverse is stopped by pressing the same button again, or it will stop automatically at the beginning or the end of the tape. The track will automatically change at the end or beginning of the tape and play will begin.

Scanning

Dolby NR1 (noise reduction system)

SC #

button. “SEEK

Press the FWD” will appear on the display. Each track will be played for 8 seconds in ascending order. The search

SC #

will stop if any of the buttons are pressed.

Skipping of blank sections (Skip-Blank)

Press the “SB” key. The Skip- Blank function is switched on or off. When switched on, the “SB” on the display is highlighted.

With the “SB” function activated and no sound signal received for approximately 10 to 15 seconds, the tape will fast forward to the next sound signal.

To enable optimum sound reproduction of cassettes recorded using the Dolby B system, press the “NR” key so the “NR” on the display is

highlighted. To turn off Dolby B noise reduction, press the “NR” key so the “NR” on the display is not highlighted.

1 Dolby and the double-D symbol Ù are trademarks of Dolby Laboratories Licensing Corporation. The Dolby noise reduction system is manufactured under licence from Dolby Laboratories Licensing Corporation.

Audio system

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

185

Instruments and controls

Audio system

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

CD mode

General notes on CD mode Should excessive temperatures occur while in CD mode, “CD TEMP HIGH” will appear on the display and muting will take place. The unit will then switch back to radio mode until the temperature has decreased to a safe operating level. Should temperatures occur while in CD mode which are too low, “CD TEMP LOW” will be displayed, but the CD will play. It will be sensitive to skipping if you are driving over rough roads. Handle CDs carefully to prevent interference during playback. Avoid fingerprints and dust on CDs. Do not write on the CDs or apply any label or other material or devices to the CDs. Clean CDs from time to time with a commercially available cleaning cloth. No solvents, anti-static sprays, etc. should be used. Replace the CD in its container after use. Protect CDs from heat and direct sunlight.

186

Only use CDs, which bear the label shown and that conform to the compact disc digital audio standard (IEC 60908). Use of CDs which do not meet this standard may cause damage to the

CD changer. Do not play single-CDs (80 mm) with an adapter.

Warning! The CD changer1 is a Class1 laser product. There is a danger of invisible laser radiation if the cover is opened or damaged. Do not remove the cover. The CD changer1 does not contain any parts which can be serviced by the user. For safety reasons, have any service work which may be necessary performed only by qualified personnel.

1 Optional equipment

CD changer1 installed

Loading/emptying the CD magazine Slide the changer door to the right until it latches open and press the eject button . The magazine will be ejected. Remove the magazine. Pull out the CD tray to its stop and place the CDs in the recess of the tray, label side up. Push the tray into the magazine in the direction shown by the arrow. Insert the loaded magazine into the changer.

Important! Close the door after the magazine has been inserted.

1 CD changer 2 CD magazine 3 CD tray 4 CD If a CD changer1 is installed, it can be operated from the front control panel of the radio. A loaded magazine must be installed for CD playing.

1 Optional equipment

Audio system

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

187

Instruments and controls

Audio system

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

188

button. If the track has been playing for

button. The next track on the CD will be

Skipping tracks forward/backward Press the played. Press the more than10 seconds, it will revert to the start of that track. If it has been playing for less than ten seconds it will revert to the preceding track. To skip several tracks, the respective button must be pressed until the desired track is reached. If the beginning or end of the CD is reached during the search, the first or last track will be played.

button. When the changer is used for the

Playing CDs Press the first time after removing/inserting a magazine, play begins at CD 1 track 1. After that, the CD most recently played will start at the point where it was last switched off. CDs stored in the magazine can be selected by using the station preset buttons 1-6.

The magazine slot number of the selected CD will be displayed after “CD”. The number of the track being