2010 Jeep Grand Cherokee SRT8 Owners Manual

Download PDF Manual
䡵 Driver Memory Seat — If Equipped . . . . . . . . . 94 ▫ Setting Memory Positions And Linking Remote Keyless Entry Transmitter To Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 ▫ Memory Position Recall . . . . . . . . . . . . . . . . . 96 ▫ To Disable a RKE Transmitter Linked To Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 ▫ Easy Entry/Exit Seat . . . . . . . . . . . . . . . . . . . 97 䡵 To Open And Close The Hood . . . . . . . . . . . . . 98 䡵 Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 ▫ Multifunction Lever . . . . . . . . . . . . . . . . . . 100 ▫ Headlights And Parking Lights . . . . . . . . . . 100 ▫ Automatic Headlights — If Equipped . . . . . . 101 ▫ Headlights On Automatically With Wipers . . 101 ▫ Smartbeam™ — If Equipped . . . . . . . . . . . . 102 ▫ Daytime Running Lights — If Equipped . . . . 103 ▫ Automatic Headlight Leveling — HID Headlights Only . . . . . . . . . . . . . . . . . . . . . 103 ▫ Instrument Panel Dimmer . . . . . . . . . . . . . . 103 ▫ Battery Saver Feature . . . . . . . . . . . . . . . . . 104 ▫ Lights-On Reminder . . . . . . . . . . . . . . . . . . 104 ▫ Fog Lights — If Equipped . . . . . . . . . . . . . . 105 ▫ Turn Signals . . . . . . . . . . . . . . . . . . . . . . . . 106 ▫ Lane Change Assist . . . . . . . . . . . . . . . . . . . 106 ▫ High/Low Beam Switch . . . . . . . . . . . . . . . 106 ▫ Flash-To-Pass . . . . . . . . . . . . . . . . . . . . . . . 106 ▫ Headlight Time Delay . . . . . . . . . . . . . . . . . 107 ▫ Interior Lights . . . . . . . . . . . . . . . . . . . . . . 107 ▫ Front Map/Reading Lights . . . . . . . . . . . . . 108 . . . . . . . . . . 109 ▫ Windshield Wiper Operation . . . . . . . . . . . . 109 ▫ Intermittent Wiper System . . . . . . . . . . . . . . 110 ▫ Windshield Washer Operation . . . . . . . . . . . . 111 ▫ Mist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111 ▫ Rain Sensing Wipers — If Equipped . . . . . . . 112 䡵 Tilt/Telescoping Steering Column . . . . . . . . . . 113 䡵 Windshield Wipers And Washers UNDERSTANDING THE FEATURES OF YOUR VEHICLE 77 䡵 Adjustable Pedals — If Equipped . . . . . . . . . . 114 䡵 Electronic Speed Control — If Equipped . . . . . 116 ▫ To Activate . . . . . . . . . . . . . . . . . . . . . . . . . 116 ▫ To Set a Desired Speed . . . . . . . . . . . . . . . . 117 ▫ To Deactivate . . . . . . . . . . . . . . . . . . . . . . . 117 ▫ To Resume Speed . . . . . . . . . . . . . . . . . . . . 117 ▫ To Vary The Speed Setting . . . . . . . . . . . . . . 117 ▫ To Accelerate For Passing . . . . . . . . . . . . . . 118 䡵 Parksense威 Rear Park Assist — If Equipped . . . 119 ▫ Parksense威 Sensors . . . . . . . . . . . . . . . . . . . 119 ▫ Parksense威 Warning Display . . . . . . . . . . . . 120 ▫ Enable/Disable Parksense威 . . . . . . . . . . . . . 121 ▫ Service Parksense威 . . . . . . . . . . . . . . . . . . . 122 78 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Cleaning Parksense威 . . . . . . . . . . . . . . . . . . 122 ▫ System Usage Precautions . . . . . . . . . . . . . . 122 䡵 Parkview威 Rear Back Up Camera — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 ▫ Turning Parkview威 On Or Off — With Navigation/Multimedia Radio . . . . . . . . . . . 126 ▫ Turning Parkview威 On Or Off — Without Navigation/Multimedia Radio . . . . . . . . . . . 127 䡵 Overhead Console . . . . . . . . . . . . . . . . . . . . . 127 ▫ Courtesy/Reading Lights . . . . . . . . . . . . . . 127 ▫ Sunglasses Storage . . . . . . . . . . . . . . . . . . . 128 䡵 Garage Door Opener — If Equipped . . . . . . . . 128 ▫ Programming HomeLink威 . . . . . . . . . . . . . . 129 ▫ Gate Operator/Canadian Programming . . . . 132 ▫ Using HomeLink威 . . . . . . . . . . . . . . . . . . . 133 ▫ Reprogramming A Single HomeLink威 Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133 ▫ Security . . . . . . . . . . . . . . . . . . . . . . . . . . . 133 ▫ Troubleshooting Tips . . . . . . . . . . . . . . . . . . 133 ▫ General Information . . . . . . . . . . . . . . . . . . 134 䡵 Power Sunroof — If Equipped . . . . . . . . . . . . 135 ▫ Opening Sunroof — Express . . . . . . . . . . . . 136 ▫ Closing Sunroof — Express . . . . . . . . . . . . . 136 ▫ Pinch Protect Feature . . . . . . . . . . . . . . . . . 136 ▫ Pinch Protect Override . . . . . . . . . . . . . . . . 136 ▫ Venting Sunroof — Express . . . . . . . . . . . . . 136 ▫ Sunshade Operation . . . . . . . . . . . . . . . . . . 136 ▫ Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . 137 ▫ Sunroof Maintenance . . . . . . . . . . . . . . . . . 137 ▫ Ignition Off Operation . . . . . . . . . . . . . . . . . 137 ▫ Sunroof Fully Closed . . . . . . . . . . . . . . . . . . 137 䡵 Electrical Power Outlets . . . . . . . . . . . . . . . . . 137 䡵 Power Inverter — If Equipped . . . . . . . . . . . . 140 䡵 Cupholders . . . . . . . . . . . . . . . . . . . . . . . . . . 143 䡵 Cargo Area Features . . . . . . . . . . . . . . . . . . . 143 . . . . . . . . . . . . . . . . . . . . . . . . 143 ▫ Cargo Light UNDERSTANDING THE FEATURES OF YOUR VEHICLE 79 ▫ Rear Storage Compartment . . . . . . . . . . . . . 144 ▫ Retractable Cargo Area Cover — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 144 ▫ Cargo Tie-Down Hooks . . . . . . . . . . . . . . . . 146 ▫ Cargo Load Floor . . . . . . . . . . . . . . . . . . . . 147 䡵 Rear Window Features . . . . . . . . . . . . . . . . . . 148 ▫ Rear Window Wiper/Washer . . . . . . . . . . . . 148 ▫ Rear Window Defroster . . . . . . . . . . . . . . . . 149 80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Automatic Dimming Mirror This mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light next to the button will illuminate to indicate when the dimming feature is activated. Automatic Dimming Mirror CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean. Outside Mirrors To receive maximum benefit, adjust the outside mirrors to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror. WARNING! Vehicles and other objects seen in the passenger-side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger-side mirror could cause you to collide with another vehicle or other objects. Use your inside mirror when judging the size or distance of a vehicle seen in the passenger-side mirror. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81 Outside Mirrors Folding Feature All outside mirrors are hinged and may be moved either forward or rearward to resist damage. The hinges have three detent positions; full forward, full rearward and normal. Driver’s Automatic Dimming Mirrors — If Equipped The driver and passenger outside mirrors will automati- cally adjust for glare from vehicles behind you. This feature is controlled by the inside automatic dimming mirror and can be turned on or off by pressing the button at the base of the inside mirror. The mirrors will auto- matically adjust for headlight glare when the inside mirror adjusts. 82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Outside Mirrors The power mirror switch is located on the driver’s door trim panel next to the power door lock switch. A rotary knob selects the left mirror, right mirror or off position. After selecting a mirror, move the knob in the same direction you want the mirror to move. Use the off (center) position to guard against accidentally moving a mirror position. Heated Mirrors — If Equipped Power Mirror Switch These mirrors are heated to melt frost or ice. This feature is activated whenever you turn on the rear window defroster. Refer to “Rear Window Features” in “Understanding the Features of Your Vehicle” for further information. Illuminated Vanity Mirrors — If Equipped To access an illuminated vanity mirror, flip down one of the sun visors. Lift the cover to reveal the mirror. The light will turn on automatically. Lighted Vanity Mirror UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83 Uconnect™ Phone — IF EQUIPPED Refer to “Uconnect™ Phone” in the Uconnect™ User Manual located on the DVD for further details. VOICE COMMAND — IF EQUIPPED Refer to “Voice Command” in the Uconnect™ Phone User Manual located on the DVD for further details. SEATS Seats are a primary part of the Occupant Restraint System of the vehicle. They need to be used properly for safe operation of the vehicle. WARNING! • DO NOT allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. In a collision, people riding in these areas are more likely to be seriously injured or killed. (Continued) 84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) • Be sure everyone in your vehicle is in a seat and using a seat belt properly. Front Manual Seat Adjustment Move the seat forward or rearward using the adjustment bar. Lift up on the bar located on the front of the seat near the floor. Using body pressure, move forward and rear- ward on the seat to be sure the seat adjusters have latched. WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted, and you could be injured. Adjust any seat only while the vehicle is parked. Front Seat Adjustment — Recline To adjust the seatback, lift the lever located on the outboard side of the seat, lean back and release the lever at the desired position. To return the seatback, lift the lever, lean forward and release the lever. WARNING! Do not ride with the seatback reclined so that the seat belt is no longer resting against your chest. In a collision, you could slide under the seat belt and be seriously or even fatally injured. Use the recliner only when the vehicle is parked. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 Manual Lumbar Support Adjustment The manual lumbar support adjustment lever is located on the right side of the driver’s seatback (all models) and on the left side of the passenger’s seatback (if equipped). Moving the lumbar control lever forward and rearward will increase or decrease the lumbar support. Eight-Way Driver’s Power Seat The driver’s power seat switches are located on the outboard side of the driver’s seat. The bottom switch controls up/down, forward/rearward and tilt adjust- ment. The top switch controls the seatback recline adjust- ment. Manual Lumbar Control Power Seat Switches 86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust any seat only while the vehicle is parked. Four-Way Passenger’s Power Seat — If Equipped The front passenger’s power seat switches are located on the outboard side of the passenger’s seat. The bottom switch controls forward/rearward adjustment. The top switch controls the seatback recline adjustment. NOTE: The four-way seat does not have an up/down adjustment. CAUTION! WARNING! DO NOT place any article under a power seat or impede its ability to move as it may cause damage to the seat controls. Seat travel may become limited if movement is stopped by an obstruction in the seat’s path. Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust any seat only while the vehicle is parked. CAUTION! DO NOT place any article under a power seat or impede its ability to move as it may cause damage to the seat controls. Seat travel may become limited if movement is stopped by an obstruction in the seat’s path. Head Restraints Head restraints can reduce the risk of injury in the event of a rear impact. The head restraint should be adjusted so the top of the head restraint is located above the top of your ear. The head restraints have a locking button which must be pushed in to lower the head restraint to all positions. The restraints may be raised without pushing in the button. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 Adjustable Head Restraints 88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Driving a vehicle with the head restraints removed or improperly adjusted could cause serious injury or death in the event of a collision. The head restraints should always be checked prior to operating the vehicle and never adjusted while the vehicle is in motion. Always adjust the head restraints when the vehicle is in PARK. Front Heated Seats — If Equipped The front driver and passenger seats are heated. The controls for each heater are located near the bottom center of the instrument panel (below the heater/air conditioning controls). The heaters provide the same average heat level for both the cushion and the seatback. After turning the ignition ON, you can choose from High, Low or Off heat settings. Amber indicator lights in each switch indicate the level of heat in use. Two indicator lights will illuminate for High, one for Low and none for Off. Press the switch once to select High-level heat- ing. Press the switch a second time to select Low-level heating. Press the switch a third time to shut the heating elements Off. When the High-level setting is selected, the heater will provide a boosted heat level during the first four minutes of operation. Then, the heat output will drop to the normal High-level. If the High-level setting is selected, the system will automatically switch to Low-level after approximately 30 minutes of continuous operation. At that time, the number of illuminated LEDs changes from two to one, indicating the change. The Low-level setting will turn Off automatically after approximately 30 min- utes. NOTE: Once a heat setting is selected, heat will be felt within two to five minutes. CAUTION! UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 Repeated overheating of the seat could damage the heating element and/or degrade the material of the seat. WARNING! • Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, ex- haustion or other physical condition must exercise care when using the seat heater. It may cause burns even at low temperatures, especially if used for long periods of time. • Do not place anything on the seat that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat. Sitting in a seat that has been overheated could cause serious burns due to the increased surface temperature of the seat. 90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Heated Seats — If Equipped On vehicles equipped with rear heated seats, the seats closest to the doors are heated. The controls for these seats are located on the rear of the center console. Rear Heated Seat Switches After turning the ignition ON, you can choose from High, Low or Off heat settings. Amber indicator lights in each switch indicate the level of heat in use. Two indicator lights will illuminate for High, one for Low and none for Off. Press the switch once to select High-level heat- ing. Press the switch a second time to select Low-level heating. Press the switch a third time to shut the heating elements Off. When the High-level setting is selected, the heater will provide a boosted heat level during the first four minutes of operation. Then, the heat output will drop to the normal High-level. If the High-level setting is selected, the system will automatically switch to Low-level after approximately 30 minutes of continuous operation. At that time, the number of illuminated LEDs changes from two to one, indicating the change. The Low-level setting will turn Off automatically after approximately 30 min- utes. NOTE: Once a heat setting is selected, heat will be felt within two to five minutes. CAUTION! UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 WARNING! • Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, ex- haustion or other physical condition must exercise care when using the seat heater. It may cause burns even at low temperatures, especially if used for long periods of time. • Do not place anything on the seat that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat. Sitting in a seat that has been overheated could cause serious burns due to the increased surface temperature of the seat. Repeated overheating of the seat could damage the heating element and/or degrade the material of the seat. 60/40 Split Rear Seat To Lower Rear Seat Either side of the rear seat can be lowered to allow for extended cargo space and still maintain some rear seating room. NOTE: Be sure that the front seats are fully upright and positioned forward. This will allow the rear seatback to fold down easily. 92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 1. Pull the release strap (toward the front of the vehicle) to release. Rear Seat Release NOTE: Do not fold the rear seat down with the center seat belt buckled. 2. Fold the rear seat completely forward. Rear Seat Folded To Raise Rear Seat Raise the rear seatback and lock it into place. If interfer- ence from the cargo area prevents the seatback from fully locking, you will have difficulty returning the seat to its proper position. WARNING! • Be certain that the seatback is securely locked into position. If the seatback is not securely locked into position the seat will not provide the proper stability for child seats and/or passengers. An improperly latched seat could cause serious injury. • The cargo area in the rear of the vehicle (with the rear seatbacks in the locked-up or folded down position) should not be used as a play area by children when the vehicle is in motion. They could be seriously injured in an accident. Children should be seated and using the proper restraint system. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 Storage (Rear Seat Armrest) — If Equipped The rear seat may be equipped with a center storage armrest. Rear Seat Armrest 94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Press the latch and lift the top of the armrest to access the storage bin. pedals and radio station preset settings. Your Remote Keyless Entry (RKE) transmitters can also be pro- grammed to recall the same positions when the UN- LOCK button is pressed. Armrest Storage Latch DRIVER MEMORY SEAT — IF EQUIPPED Once programmed, the memory buttons 1 and 2 on the driver’s door panel can be used to recall the driver’s seat, driver’s outside mirror, adjustable brake and accelerator Driver Memory Switches Your vehicle is equipped with two RKE transmitters. One or both RKE transmitters can be linked to either memory position. The memory system can accommodate up to four RKE transmitters, each one linked to either of the two memory positions. Setting Memory Positions and Linking Remote Keyless Entry Transmitter to Memory NOTE: Each time the S (SET) button and a numbered button 1 or 2 are pressed, you erase the memory settings for that button and store a new one. 1. Insert the ignition key, and turn the ignition switch to the ON position. 2. Press the driver door MEMORY button number 1 if you are setting the memory for driver 1, or button number 2 if you are setting the memory for driver 2. The system will recall any stored settings. Wait for the system to complete the memory recall before continuing to Step 3. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 3. Adjust the driver’s seat, recliner, and driver’s sideview mirror to the desired positions. 4. Adjust the brake and accelerator pedals to the desired positions. 5. Turn on the radio and set the radio station presets (up to 12 AM and 12 FM stations can be set). 6. Turn the ignition switch to the LOCK position and remove the key. 7. Press and release the S (SET) button located on the driver’s door. 8. Within five seconds, press and release MEMORY button 1 or 2 on the driver’s door. The next step must be performed within five seconds if you desire to also use a RKE transmitter to recall memory positions. 9. Press and release the LOCK button on one of the RKE transmitters. 96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 10. Insert the ignition key, and turn the ignition switch to the ON position. 11. Select ⬙Remote Linked to Memory⬙ in the Electronic Vehicle Information Center (EVIC) and enter ⬙Yes⬙. Refer to “Electronic Vehicle Information Center (EVIC)/ Customer-Programmable Features” in “Understanding Your Instrument Panel” for further information. 12. Repeat the above steps to set the next memory position, using the other numbered memory button, or to link another RKE transmitter to memory. Memory Position Recall NOTE: The vehicle must be in PARK to recall memory positions. If a recall is attempted when the vehicle is not in PARK, a message will be displayed in the Electronic Vehicle Information Center (EVIC). To recall the memory settings for driver one, press MEMORY button number 1 on the driver’s door, or the UNLOCK button on the RKE transmitter linked to memory position 1. To recall the memory setting for driver two, press MEMORY button number 2 on the driver’s door, or the UNLOCK button on the RKE transmitter linked to memory position 2. A recall can be cancelled by pressing any of the MEMORY buttons on the drivers door during a recall (S, 1, or 2). When a recall is cancelled, the driver’s seat, driver’s mirror and the pedals stop moving. A delay of one second will occur before another recall can be selected. To Disable a RKE Transmitter Linked to Memory 1. Turn the ignition switch to the LOCK position, and remove the key. 2. Press and release MEMORY button number 1. The system will recall any memory settings stored in position 1. Wait for the system to complete the memory recall before continuing to Step 3. 3. Press and release the memory S (SET) button located on the driver’s door. 4. Within five seconds, press and release MEMORY button 1 on the driver’s door. 5. Within five seconds, press and release the UNLOCK button on the RKE transmitter. To disable another RKE transmitter linked to either memory position, repeat steps 1 through 5 for each RKE transmitter. NOTE: Once programmed, all RKE transmitters linked to memory can be easily enabled or disabled at one time. Refer to “Electronic Vehicle Information Center (EVIC)/ Customer-Programmable Features” in “Understanding Your Instrument Panel” for further information. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 Easy Entry/Exit Seat This feature provides automatic driver’s seat positioning which will enhance driver mobility out of and into the vehicle. There are two possible Easy Entry/Exit adjustments available: • The seat cushion will move rearward approximately 2.5 in (60 mm), if the starting position of the seat is greater than or equal to 2.67 in (68 mm) forward of the rear seat stop when the key is removed from the ignition switch. The seat will then move forward approximately 2.5 in (60 mm) when the key is placed into the ignition and turned out of the LOCK position. • The seat will move to the position located 0.3 in (8 mm) forward of the rear stop if the starting position is between 0.9 to 2.67 in (23 to 68 mm) forward of the rear stop when the key is removed from the ignition switch. The seat will move forward to the memory/ 98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE driving position when the key is placed into the ignition, and turned out of the LOCK position toward the ACC/ON position. The Easy Entry/Exit feature will be automatically dis- abled if the seat is already positioned closer than 0.9 in (23 mm) forward of the rear stop. At this position, there is no benefit to the driver by moving the seat for Easy Exit/Entry. Each stored memory setting will have an associated Easy Entry/Exit position. NOTE: The Easy Entry/Exit feature is not enabled when the vehicle is delivered from the factory. The Easy Entry/Exit feature is enabled (or later disabled) through the programmable features in the Electronic Vehicle Information Center (EVIC). Refer to “Electronic Vehicle Information Center (EVIC)/Customer-Programmable Features” in “Understanding Your Instrument Panel” for further information. TO OPEN AND CLOSE THE HOOD Two latches must be released to open the hood. 1. Pull the release lever inside your vehicle located below the instrument panel and in front of the driver’s door. Hood Release Handle 2. Reach under the hood, move safety latch to the left and lift the hood. CAUTION! UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the center of the hood to ensure that both latches engage. WARNING! Be sure the hood is fully latched before driving your vehicle. If the hood is not fully latched, it could open when the vehicle is in motion and block your vision. Failure to follow this warning could result in serious injury or death. Safety Latch Location 100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE LIGHTS Multifunction Lever The multifunction lever controls the operation of the headlights, turn signals, headlight beam selection, instru- ment panel light dimming, passing light, interior courtesy/ dome lights and optional fog lights. The multifunction lever is located on the left side of the steering wheel. Headlights and Parking Lights Turn the end of the multifunction lever to the first detent for parking light operation. Turn to the second detent for headlight operation. Turn to the third detent for Auto- matic Headlight operation (if equipped). Multifunction Lever Headlight Switch Automatic Headlights — If Equipped Turn the end of the multifunction lever to the third detent (AUTO) to activate the Automatic Headlight system. Multifunction Lever UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 This system performs two functions. With the engine running and the multifunction lever in the AUTO posi- tion, the headlights will turn on and off based on the surrounding light levels. Headlights On Automatically With Wipers If your vehicle is equipped with Automatic Headlights, it also has this customer-programmable feature. When your headlights are in the automatic mode and the engine is running, they will automatically turn on when the wiper system is on. Refer to “Electronic Vehicle Information Center (EVIC)/Customer-Programmable Features” in “Understanding Your Instrument Panel” for further information. If your vehicle is equipped with a “Rain Sensitive Wiper System” and it is activated, the headlights will automati- cally turn on after the wipers complete five wipe cycles within approximately one minute, and they will turn off 102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE approximately four minutes after the wipers completely stop. Refer to “Windshield Wipers and Washers” in this section for further information. NOTE: When your headlights come on during the daytime, the instrument panel lights will automatically dim to the lower nighttime intensity. Refer to “Lights” in this section for further information. SmartBeam™ — If Equipped The SmartBeam™ system provides increased forward lighting at night by automating high beam control through the use of a digital camera mounted on the inside rearview mirror. This camera detects vehicle spe- cific light and automatically switches from high beams to low beams until the approaching vehicle is out of view. If the windshield or SmartBeam™ mirror is NOTE: replaced, the SmartBeam™ mirror must be re-aimed to ensure proper performance. See your local authorized dealer. Center Information To Activate 1. Select “Auto High Beams.” Refer to “Electronic Ve- hicle (EVIC)/Customer- Programmable Features” in “Understanding Your Instru- ment Panel” for further information. 2. Turn the end of the multifunction lever to the AUTO headlight position. 3. Push the multifunction lever away from you (toward front of vehicle) to engage the high beam mode. NOTE: This system will not activate until the vehicle is at or above 20 mph (32 km/h). To Deactivate 1. Pull back on the multifunction lever to manually deactivate the system (normal operation of low beams). 2. Push back on the multifunction lever once again to reactivate the system. NOTE: Broken, muddy, or obstructed headlights and taillights of vehicles in the field of view will cause headlights to remain on longer (closer to the vehicle). Also, dirt, film, and other obstructions (sticker, toll box, etc.) on the windshield or camera lens will cause the system to function improperly. Daytime Running Lights — If Equipped The high beam headlights come on at a low intensity level whenever the engine is running, and the transmis- sion is not in the PARK position. The lights will remain on until the ignition switch is turned to LOCK/ACC or the parking brake is engaged. The headlight switch must be used for normal nighttime driving. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 Automatic Headlight Leveling — HID Headlights Only This feature prevents the headlights from interfering with the vision of oncoming drivers. Headlight leveling automatically adjusts the height of the headlight beam in reaction to changes in vehicle pitch. Instrument Panel Dimmer Rotate the center potion of the lever to the extreme bottom position to fully dim the instrument panel lights and prevent the interior lights from illuminating when a door is opened. Rotate the center portion of the lever up to increase the brightness of the instrument panel lights when the park- ing lights or headlights are on. Rotate the center portion of the lever upward to the next detent position to brighten the odometer and radio when the parking lights or headlights are on. 104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rotate the center portion of the lever upward to the last detent to turn on the interior lighting. Battery Saver Feature If the multifunction lever is left in the interior light position, parking light position, or the headlight position when the ignition switch is moved to the LOCK position, the battery saver feature will automatically turn off the exterior and interior lights after eight minutes. Normal operation will resume when the ignition is turned ON or when the headlight switch is turned to another position. Lights-On Reminder If the headlights or parking lights are on after the ignition switch has been turned to LOCK/ACC, a chime will sound when the driver’s door is opened. Dimmer Control Fog Lights — If Equipped The fog light switch is located in the multifunction lever. To activate the fog lights, turn on the park/ turn lights, low beam headlights or the Automatic Headlights and pull out the end of the multifunction lever. A light in the instrument cluster shows when the fog lights are on. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 lights. NOTE: • Turning on the high beam headlights turns off the fog • A front fog light is a lighting device that provides illumination in front of the vehicle under conditions of fog, rain, snow, or dust. The front fog lights supple- ment the low beams of a standard headlight system. • Proper aim and adjustment of the front fog lights should be made to prevent excessive glare for other drivers. Front Fog Light Control 106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turn Signals Move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights. Turn Signal Control If either light remains on and does not flash, or NOTE: there is a very fast flash rate, check for a defective outside that it would suggest light bulb. If an indicator fails to light when the lever is moved, the indicator bulb is defective. Lane Change Assist Tap the lever up or down once, without moving beyond the detent, and the turn signal (right or left) will flash three times then automatically turn off. High/Low Beam Switch Push the multifunction lever away from you to switch the headlights to high beam. Pull the multifunction lever toward you to switch the headlights back to low beam. Flash-to-Pass You can signal another vehicle by lightly pulling the multifunction lever toward the steering wheel. This will turn on the high beam headlights until the lever is released. Headlight Time Delay This feature delays turning off the headlights for 30, 60 or 90 seconds after the ignition switch is turned OFF. To activate the headlight delay, the multifunction lever must be rotated to the “Off” position after the ignition switch is turned to LOCK/ACC. Only the headlights will illu- minate during this time. Refer to “Electronic Vehicle Information Center (EVIC)/Customer-Programmable Features” in “Understanding Your Instrument Panel” for further information. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 Interior Lights The interior lighting consists of courtesy lights (below the instrument panel), an overhead console light (which contains both driver and passenger reading lights), read- ing lights (located above the rear doors), and a rear cargo light. Opening a door, pressing the UNLOCK button on the Remote Keyless Entry (RKE) transmitter or turning the center of the multifunction lever to the extreme up position, will activate all interior courtesy lights. 108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Map/Reading Lights These lights are mounted in the overhead console. Each light can be turned on by pressing the recessed area of the lens. To turn these lights off, press the recessed area of the lens a second time. There are also reading lights located above the rear doors. Each light can be turned on by pressing the front recessed area of the lens. To turn these lights off, press the recessed area of the lens a second time. Front Map/Reading Lights WINDSHIELD WIPERS AND WASHERS The windshield wiper/washer control lever is located on the right side of the steering column. The front wipers are operated by rotating a switch, located on the end of the lever. For information on the rear wiper/washer, refer to “Rear Window Features” in “Understanding the Features of Your Vehicle”. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 Windshield Wiper Operation Rotate the end of the lever upward to the LO position for low-speed wiper operation. Rotate the end of the lever upward to the HI position for high-speed wiper operation. Windshield Wiper/Washer Switch Front Wiper Control 110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Always remove any buildup of snow that prevents the windshield wiper blades from returning to the “park” position. If the windshield wiper switch is turned off, and the blades cannot return to the “park” position, damage to the wiper motor may occur. Intermittent Wiper System Use one of the five intermittent wiper speeds when weather conditions make a single wiping cycle, with a variable pause between cycles, desirable. Turn the end of the lever to one of the five delay positions for the desired delay interval. The delay can be regulated from a maxi- mum of approximately 18 seconds between cycles, to a cycle every 1/2 second. Front Wiper Control NOTE: The wiper delay times depend on vehicle speed. If the vehicle is moving less than 10 mph (16 km/h), delay times will be doubled. Windshield Washer Operation To use the washer, pull the lever toward you and hold while spray is desired. If the lever is pulled while in the delay range, the wiper will operate for several wipe cycles after the lever is released, and then resume the intermittent interval previously selected. If the lever is pulled while in the off position, the wipers will operate for several wipe cycles, then turn off. WARNING! Sudden loss of visibility through the windshield could lead to an accident. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with the defroster before and during windshield washer use. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 Mist Use the Mist feature when weather conditions make occasional usage of the wipers necessary. Pull down and release the control lever for a single wiping cycle. Mist Control 112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rain Sensing Wipers — If Equipped This feature senses moisture on the windshield and automatically activates the wipers for the driver. The feature is especially useful for road splash or overspray from the windshield washers of the vehicle ahead. Rotate the end of the multifunction lever to one of five settings to activate this feature. The sensitivity of the system can be adjusted with the multifunction lever. Wiper delay position 1 is the least sensitive, and wiper delay position 5 is the most sensi- tive. Setting 3 should be used for normal rain conditions. Settings 1 and 2 can be used if the driver desires less wiper sensitivity. Settings 4 and 5 can be used if the driver desires more sensitivity. Place the wiper switch in the OFF position when not using the system. NOTE: • The Rain Sensing feature will not operate when the wiper switch is in the low or high-speed position. may reduce Rain Sensing performance. ice, or dried salt water is present on the windshield. • The Rain Sensing feature may not function properly when • Use of Rain-X威 or products containing wax or silicone • A customer programmable feature in the Electronic Vehicle Information Center (EVIC) allows the Rain Sensing feature to be turned off. Refer to “Electronic Vehicle Information Center (EVIC)/Personal Settings (Customer-Programmable Features)” in “Understand- ing Your Instrument Panel” for further information. The Rain Sensing system has protection features for the wiper blades and arms, and will not operate under the following conditions: • Low Ambient Temperature — When the ignition is first turned ON, the Rain Sensing system will not operate until the wiper switch is moved, vehicle speed is greater than 0 mph (0 km/h), or the outside tem- perature is greater than 32°F (0°C). • Transmission in NEUTRAL Position — When the ignition is ON, and the transmission is in the NEU- TRAL position, the Rain Sensing system will not operate until the wiper switch is moved, vehicle speed is greater than 5 mph (8 km/h), or the shift lever is moved out of the NEUTRAL position. TILT/TELESCOPING STEERING COLUMN This feature allows you to tilt the steering column upward or downward. It also allows you to lengthen or shorten the steering column. The tilt/telescoping control handle is located below the steering wheel at the end of the steering column. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 Tilt/Telescoping Control Handle To unlock the steering column, push the control handle downward (toward the floor). To tilt the steering column, move the steering wheel upward or downward as de- sired. To lengthen or shorten the steering column, pull the steering wheel outward or push it inward as desired. To lock the steering column in position, push the control handle upward until fully engaged. 114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the vehicle. Be sure the steering column is locked before driving your ve- hicle. Failure to follow this warning may result in serious injury or death. ADJUSTABLE PEDALS — IF EQUIPPED This feature allows both the brake and accelerator pedals to move toward or away from the driver to provide improved position with the steering wheel. The adjust- able pedal system is designed to allow a greater range of driver comfort for steering wheel tilt and seat position. The position of the brake and accelerator pedals can be adjusted without compromising safety or comfort in actuating the pedals. Adjustable Pedal Switch Press the bottom of the switch to move the pedals forward (away from the driver). Press the top of the switch to move the pedals rearward (toward the driver). • The pedals can be adjusted with the ignition OFF. • The pedals can be adjusted while driving. • The pedals cannot be adjusted when the vehicle is in REVERSE (R) or when the Electronic Speed Control is on. A message will be displayed in the Electronic Vehicle Information Center (EVIC) if the pedals are attempted to be adjusted when the system is locked out (“Adjustable Pedal Disabled — Cruise Control Set” or “Adjustable Pedal Disabled — Shifter In Re- verse”). Refer to “Electronic Vehicle Information Cen- ter Instrument Panel” for further information. (EVIC)” in “Understanding Your UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 CAUTION! Do not place any article under the adjustable pedal’s or impede its ability to move as it may cause damage to the pedal controls. Pedal travel may become lim- ited if movement is stopped by an obstruction in the adjustable pedal’s path. WARNING! Do not adjust the pedals while the vehicle is moving. You could lose control and have an accident. Always adjust the pedals while the vehicle is parked. 116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, Electronic Speed Control takes over accelerator operations at speeds greater than 25 mph (40 km/h). The Electronic Speed Control lever is located on the right side of the steering wheel. In order to ensure proper operation, the Elec- NOTE: tronic Speed Control System has been designed to shut down if multiple Speed Control functions are operated simultaneously. If this occurs, the Electronic Speed Con- trol System can be reactivated by pushing the Electronic Speed Control ON/OFF button and resetting the desired vehicle set speed. To Activate Push the ON/OFF button. The Cruise Indicator Light in the instrument cluster will illuminate. To turn the system OFF, push the ON/OFF button a second time. The Cruise Indicator Light will turn off. The system should be turned OFF when not in use. Electronic Speed Control Lever WARNING! Leaving the Electronic Speed Control System on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system OFF when you are not using it. To Set a Desired Speed When the vehicle has reached the desired speed, press down on the lever and release. Release the accelerator and the vehicle will operate at the selected speed. NOTE: The vehicle should be traveling at a steady speed and on level ground before pressing the SET lever. To Deactivate A soft tap on the brake pedal, pulling the lever toward you, or normal brake pressure while slowing the vehicle will deactivate Electronic Speed Control without erasing UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 the set speed memory. Pressing the ON/OFF button or turning off the ignition switch erases the set speed memory. To Resume Speed To resume a previously set speed, push the RESUME ACCEL lever up and release. Resume can be used at any speed above 25 mph (40 km/h). To Vary the Speed Setting When the Electronic Speed Control is set, you can in- crease speed by pushing up and holding the RESUME ACCEL lever. If the lever is continually held in the RESUME ACCEL position, the set speed will continue to increase until the lever is released, then the new set speed will be established. Tapping RESUME ACCEL once will result in a 1 mph (2 km/h) speed increase. Each time the lever is tapped the vehicle speed increases, so that tapping the lever three times will increase speed by 3 mph (5 km/h). 118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To decrease speed while the Electronic Speed Control is set, push down and hold the SET DECEL lever. If the lever is continually held in the SET DECEL position, the set speed will continue to decrease until the lever is released. Release the lever when the desired speed is reached, and the new set speed will be established. Tapping the SET DECEL lever once will result in a 1 mph (2 km/h) speed decrease. Each time the lever is tapped, vehicle speed decreases. To Accelerate for Passing Press the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. Using Electronic Speed Control On Hills The transmission may downshift on hills to maintain the vehicle set speed. NOTE: The Electronic Speed Control System maintains speed up and down hills. A slight speed change on moderate hills is normal. On steep hills, a greater speed loss or gain may occur so it may be preferable to drive without Electronic Speed Control. WARNING! Electronic Speed Control can be dangerous where the system cannot maintain a constant speed. Your ve- hicle could go too fast for the conditions, and you could lose control. An accident could be the result. Do not use Electronic Speed Control in heavy traffic or on roads that are winding, icy, snow-covered or slippery. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 ParkSense姞 Sensors The four ParkSense威 sensors, located in the rear fascia, monitor the area behind the vehicle that is within the sensors’ field of view. The sensors can detect obstacles from approximately 12 to 59 in (30 to 150 cm) from the rear fascia in the horizontal direction, depending on the location and orientation of the obstacle and the type of obstacle. PARKSENSE姞 REAR PARK ASSIST — IF EQUIPPED ParkSense威 provides visible and audible indications of the distance between the rear fascia and the detected obstacle when backing up. Refer to the Warning Section and Note Section for limitations of this system and recommendations. ParkSense威 will remember the last system state (enabled or disabled) from the last ignition cycle when the ignition is changed to the ON position. ParkSense威 can be active only when the shift lever is in REVERSE. If ParkSense威 is enabled at this shift lever position, the system will be active until the vehicle speed is increased to approximately 11 mph (18 km/h) or above. The system will be active again if the vehicle speed is decreased to speeds less than approximately 10 mph (16 km/h). 120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ParkSense姞 Warning Display The ParkSense威 warning display, located in the headliner near the flipper glass, provides both visible and audible warnings to indicate the distance between the rear fascia and the detected obstacle. When the ignition is turned to the ON position, the warning display will turn ON all of its LEDs for about one second. Each side of the warning display has six yellow and two red LEDs. The vehicle is close to the obstacle when the red LED is ON. The system dimly illuminates the two outer most yellow LEDs when it is ON and detecting no obstacles. The following chart shows the warning display operation when the system is detecting an obstacle: ParkSense威 Display WARNING DISPLAY DISTANCES DISPLAY LED OBSTACLE DISTANCE FROM: LED COLOR AUDIBLE SIGNAL UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 1st LED 2nd LED 3rd LED 4th LED 5th LED 6th LED 7th LED 8th LED REAR CORNERS 31.5 in (80 cm) 25.5 in (65 cm) 20 in (50 cm) 16 in (40 cm) 6 in (15 cm) REAR CENTER 59 in (150 cm) 51 in (130 cm) 45 in (115 cm) 39 in (100 cm) 33.5 in (85 cm) 28 in (70 cm) 20 in (50 cm) 12 in (30 cm) NOTE: The Rear Park Assist system will MUTE the radio, if on, when the system is sounding an audio tone. Enable/Disable ParkSense姞 ParkSense威 can be enabled and disabled with a switch located on the upper switch bank of the instrument panel. Yellow Yellow Yellow Yellow Yellow Yellow Red Red Yes, Half Second None None None None None Yes, Intermittent Yes, Continuous Press the switch once to turn ParkSense威 on, push the switch a second time to turn Park- Sense威 off. 122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When the switch is pressed to disable the system, the instrument cluster will display the “PARK ASSIST DIS- ABLED” message. Refer to “Electronic Vehicle Informa- tion Center (EVIC)” in “Understanding Your Instrument Panel” for further information. When the shift lever is changed to REVERSE and the system is disabled, the instrument cluster will actuate a single chime, once per ignition cycle, and it will display the message. The ParkSense威 switch LED will be ON when the system is disabled or defective. The ParkSense威 switch LED will be OFF when the system is enabled. Service ParkSense姞 When ParkSense威 is defective, the instrument cluster will actuate a single chime, once per ignition cycle, and it will display the “SERVICE PARK ASSIST SYSTEM” message. Refer to “Electronic Vehicle Information Center (EVIC)” in “Understanding Your Instrument Panel” for further information. If “SERVICE PARK ASSIST SYSTEM” ap- pears in the EVIC after making sure the rear fascia/ bumper is clean and free of snow, ice, mud, or other debris, see your authorized dealer. Cleaning ParkSense姞 Clean the ParkSense威 sensors with water, car wash soap and a soft cloth. Do not use rough or hard cloths. Do not scratch or poke the sensors. Otherwise, you could dam- age the sensors. System Usage Precautions NOTE: • Ensure that the rear bumper is free of dirt and debris • Jackhammers, large trucks, and other vibrations could to keep ParkSense威 operating properly. affect the performance of ParkSense威. • When you turn ParkSense威 off, the instrument cluster will display “PARK ASSIST DISABLED.” Further- more, once you turn ParkSense威 off, it remains off until you turn it on again, even if you cycle the ignition key. • When you move the shift lever to the REVERSE position and ParkSense威 is turned off, the instrument cluster will display “PARK ASSIST DISABLED” mes- sage for as long as the vehicle is in REVERSE. • ParkSense威, when on, will MUTE the radio when it is • If a ParkSense威 system malfunction occurs, a single chime will sound once per ignition cycle. In addition, the Electronic Vehicle Information Center (EVIC) will display “SERVICE PARK ASSIST SYSTEM”. If this occurs making sure the rear fascia/bumper is free from snow, ice, mud, dirt and debris, see your autho- rized dealer. sounding a tone. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 • Clean the ParkSense威 sensors regularly, taking care not to scratch or damage them. The sensors must not be covered with ice, snow, slush, mud, dirt, or debris. Failure to do so can result in the system not working properly. ParkSense威 might not detect an obstacle behind the fascia/bumper, or it could provide a false indication that an obstacle is behind the fascia/ bumper. • Objects must not be within 12 in (30 cm) from the rear fascia/bumper while driving the vehicle. Failure to do so can result in the system misinterpreting a close object as a sensor problem, causing the “SERVICE PARK ASSIST SYSTEM” message to be displayed in the instrument cluster. 124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! • ParkSense威 is only a parking aid and it is unable to recognize every obstacle, including small ob- stacles. Parking curbs might be temporarily de- tected or not detected at all. Obstacles located above or below the sensors will not be detected when they are in close proximity. • The vehicle must be driven slowly when using ParkSense威 to be able to stop in time when the obstacle is detected. It is recommended that the driver looks over his/her shoulder when using ParkSense威. WARNING! • Drivers must be careful when backing up even when using the ParkSense威 Rear Park Assist Sys- tem. Always check carefully behind your vehicle, look behind you, and be sure to check for pedes- trians, animals, other vehicles, obstructions, and blind spots before backing up. You are responsible for safety and must continue to pay attention to your surroundings. Failure to do so can result in serious injury or death. (Continued) WARNING! (Continued) • Before using the ParkSense威 Rear Park Assist System, it is strongly recommended that the ball mount and hitch ball assembly is disconnected from the vehicle when the vehicle is not used for towing. Failure to do so can result in injury or damage to vehicles or obstacles because the hitch ball will be much closer to the obstacle than the rear fascia when the warning display turns on the single flashing arc and sounds the continuous tone. Also, the ParkSense威 sensors could detect the ball mount and hitch ball assembly, depending on its size and shape, giving a false indication that an obstacle is behind the vehicle. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 PARKVIEW姞 REAR BACK UP CAMERA — IF EQUIPPED Your vehicle may be equipped with the ParkView威 Rear Back Up Camera that allows you to see an on-screen image of the rear of your vehicle whenever the shift lever is put into REVERSE. The image will be displayed on the Navigation/Multimedia radio display screen. The Park- View威 camera is located on the rear liftgate. WARNING! Drivers must be careful when backing up even when using the ParkView威 Rear Back Up Camera. Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, ob- structions, or blind spots before backing up. You are responsible for the safety of your surroundings and must continue to pay attention while backing up. Failure to do so can result in serious injury or death. 126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! • To avoid vehicle damage, ParkView威 should only be used as a parking aid. The ParkView威 camera is unable to view every obstacle or object in your drive path. • To avoid vehicle damage, the vehicle must be driven slowly when using ParkView威 to be able to stop in time when an obstacle is seen. It is recom- mended that the driver look frequently over his/ her shoulder when using ParkView威. If snow, ice, mud, or anything else builds up on NOTE: the camera lens, clean the lens, rinse with water, and dry with a soft cloth. Do not cover the lens. Turning ParkView姞 On or Off — With Navigation/Multimedia Radio 1. Press the “menu” hard key. 2. Select “system setup” soft key. 3. Press the “camera setup” soft key. 4. Enable or disable the rear camera feature by selecting “enable rear camera in reverse” soft key. 5. Press the “save” soft key. 6. When the vehicle is shifted into REVERSE, an image of the rear of the vehicle will appear with a caution note to ⬙check entire surroundings⬙ displayed across the top of the screen. After five seconds this note will disappear. 7. When the vehicle is shifted out of REVERSE, the rear camera mode is exited and the navigation or audio screen appears again. Turning ParkView姞 On or Off — Without Navigation/Multimedia Radio 1. Press the “menu” hard key. 2. Select “system setup” soft key. 3. Enable or disable the rear camera feature by selecting “enable rear camera in reverse” soft key. 4. When the vehicle is shifted into REVERSE, an image of the rear of the vehicle will appear with a caution note to “check entire surroundings” displayed across the top of the screen. After five seconds this note will disappear. 5. When the vehicle is shifted out of REVERSE, the rear camera mode is exited and the audio screen appears again. OVERHEAD CONSOLE The overhead console contains courtesy/reading lights, storage for sunglasses. Universal Garage Door Opener UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 (HomeLink威) and power sunroof switches may also be included, if equipped. Courtesy/Reading Lights Overhead Console At the forward end of the console are two courtesy/ reading lights. 128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Press the lens to turn these lights on. Press a second time to turn the lights off. The lights also turn on when a front door or rear door is opened. The lights will also turn on when the UNLOCK button on the Remote Keyless Entry (RKE) transmitter is pressed. Sunglasses Storage At the rear of the console a compartment is provided for the storage of a pair of sunglasses. The storage compartment access is a “push/push” de- sign. Push the finger depression on the overhead console to open. Push the finger depression to close. GARAGE DOOR OPENER — IF EQUIPPED HomeLink威 replaces up to three remote controls (hand- held transmitters) that operate devices such as garage door openers, motorized gates, lighting or home security systems. The HomeLink威 unit operates off your vehicle’s battery. The HomeLink威 buttons are located in the overhead console and contain one, two or three dots/lines desig- nating the different HomeLink威 channels. HomeLink威 Buttons NOTE: HomeLink威 is disabled when the Vehicle Secu- rity Alarm is active. WARNING! • Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people, pets or other objects are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by federal safety standards. This includes most garage door opener models manufactured after 1982. Do not use a garage door opener without these safety features. Call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for safety infor- mation or assistance. (Continued) UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 WARNING! (Continued) • Vehicle exhaust contains carbon monoxide, a dan- gerous gas. Do not run your vehicle in the garage while training the transceiver. Exhaust gas can cause serious injury or death. Programming HomeLink姞 Before You Begin If you have not trained any of the HomeLink威 buttons, erase all channels before you begin training. To do this, press and hold the two outside buttons for up to 20 seconds. The EVIC will display “CLEARING CHANNELS.” Release the buttons when the EVIC mes- sage states “CHANNELS CLEARED.” It is recommended that a new battery be placed in the hand-held transmitter of the device being copied to training and accurate 130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE HomeLink威 for more efficient transmission of the radio-frequency signal. Your vehicle should be parked outside of the garage while training. 1. Turn the ignition switch to the ON/RUN position. 2. Place the handheld transmitter 1 to 3 in (3 to 8 cm) from the HomeLink威 buttons while keeping the EVIC display in view. For optimal training, point the battery end of the hand- held transmitter away from the HomeLink威. 3. Simultaneously, press and hold both the chosen HomeLink威 button and the handheld transmitter button until the EVIC display changes from “CHANNEL # TRAINING” to “CHANNEL # TRAINED.” Then release both the HomeLink威 and handheld trans- mitter buttons. If the EVIC display states “DID NOT TRAIN” repeat Step 3. If the signal is too weak, replace the battery in the handheld transmitter. It may take up to 30 seconds or longer in rare cases. The garage door may open and close while you train. NOTE: Some gate operators and garage door openers may require you to replace Step 3 with procedures noted in the “Gate Operator/Canadian Programming” section. 4. Press and hold the just-trained HomeLink威 button. If the channel has been trained, the EVIC display will now state “CHANNEL # TRANSMIT.” If the EVIC display still states “CHANNEL # TRAIN- ING” repeat Step 3. NOTE: After training a HomeLink威 channel, if the garage door does not operate with HomeLink威 and the garage door opener was manufactured after 1995, the garage door opener may have rolling code. If so, proceed to the heading “Programming A Rolling Code System.” 5. PROGRAMMING A ROLLING CODE SYSTEM At the garage door opener motor (in the garage), locate the “Learn” or “Training” button. This can usually be found where the hanging antenna wire is attached to the garage door opener motor (it is NOT the button normally used to open and close the door). UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 1 — Garage Door Opener 2 — Training Button 6. Firmly press and release the LEARN or TRAINING button. The name and color of the button may vary by manufacturer. NOTE: You have 30 seconds in which to initiate the next step after the LEARN button has been pressed. 132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 7. Return to the vehicle and press the programmed HomeLink威 button twice (holding the button for two seconds each time). If the device is plugged in and activates, programming is complete. If the device does not activate, press the button a third time (for two seconds) to complete the training. If you have any problems or require assistance, please call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for information or assistance. To program the remaining two HomeLink威 buttons, repeat each step for each remaining button. DO NOT erase the channels. Gate Operator/Canadian Programming Canadian radio-frequency laws require transmitter sig- nals to “time-out” (or quit) after several seconds of transmission – which may not be long enough for HomeLink威 to pick up the signal during programming. Similar to this Canadian law, some U.S. gate operators are designed to “time-out” in the same manner. It may be helpful to unplug the device during the cycling process to prevent possible overheating of the garage door or gate motor. If you are having difficulties programming a garage door opener or a gate operator, replace “Programming HomeLink” Step 3 with the following: 3. Continue to press and hold the HomeLink威 button, while you press and release (“cycle”), your handheld transmitter every two seconds until HomeLink威 has successfully accepted the frequency signal. The EVIC display will change from “CHANNEL # TRAINING” to “CHANNEL # TRAINED.” If you unplugged the device for training, plug it back in at this time. and release Then proceed with Step 4 under “Programming HomeLink威” earlier in this section. Using HomeLink姞 the programmed To operate, press HomeLink威 button. Activation will now occur for the trained device (i.e., garage door opener, gate operator, security system, entry door lock, home/office lighting, etc.,). The handheld transmitter of the device may also be used at any time. Reprogramming A Single HomeLink姞 Button To reprogram a channel that has been previously trained, follow these steps: 1. Turn the ignition switch to the ON/RUN position. 2. Press and hold the desired HomeLink威 button for 20 seconds until the EVIC display states “CHANNEL # TRAINING.” Do not release the button. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 3. Without releasing the button, proceed with Program- ming HomeLink威 Step 2 and follow all remaining steps. Security It is advised to erase all channels before you sell or turn in your vehicle. To do this, press and hold the two outside buttons for 20 seconds until the EVIC message states “CHANNELS CLEARED.” Note that all channels will be erased. Indi- vidual channels cannot be erased. The HomeLink威 Universal Transceiver is disabled when the Vehicle Security Alarm is active. Troubleshooting Tips If you are having trouble programming HomeLink威, here are some of the most common solutions: • Replace the battery in the original transmitter. 134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Press the LEARN button on the garage door opener to • Did you unplug the device for training and remember complete the training for rolling code. to plug it back in? If you are having any problems or require assistance, please call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for information or assistance. General Information This device complies with FCC rules Part 15 and Industry Canada RSS-210. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference that may be received including interference that may cause undesired operation. NOTE: The transmitter has been tested and it complies with FCC and IC rules. Changes or modifications not expressly approved by the party responsible for compli- ance could void the user’s authority to operate the device. The term “IC:” before the certification/registration num- ber only signifies that Industry Canada technical specifi- cations were met. POWER SUNROOF — IF EQUIPPED The power sunroof switch is located between the sun visors on the overhead console. Power Sunroof Switch UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 WARNING! • Never leave children in a vehicle with the key in the ignition switch. Occupants, particularly unat- tended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death. • In an accident, there is a greater risk of being thrown from a vehicle with an open sunroof. You could also be seriously injured or killed. Always fasten your seat belt properly and make sure all passengers are properly secured too. • Do not allow small children to operate the sun- roof. Never allow your fingers, other body parts, or any object to project through the sunroof opening. Injury may result. 136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Opening Sunroof — Express Press the switch rearward and release, and the sunroof will open automatically from any position. The sunroof will open fully, then stop automatically. This is called “Express Open”. During Express Open operation, any movement of the sunroof switch will stop the sunroof. Closing Sunroof — Express Press the switch forward and release, and the sunroof will close automatically from any position. The sunroof will close fully and stop automatically. This is called “Express Close”. During Express Close operation, any movement of the switch will stop the sunroof. Pinch Protect Feature This feature will detect an obstruction in the opening of the sunroof during Express Close operation. If an ob- struction is detected, the sunroof will automatically re- tract. Remove the obstruction if this occurs. Next, press the switch forward and release to Express Close. Pinch Protect Override If a known obstruction (ice, debris, etc.) prevents closing the sunroof, press the switch forward and hold for two seconds after the reversal occurs. This allows the sunroof to move toward the closed position. NOTE: Pinch protection is disabled while the switch is pressed. Venting Sunroof — Express Press and release the “Vent” button, and the sunroof will open to the vent position. This is called “Express Vent”, and will occur regardless of sunroof position. During Express Vent operation, any movement of the switch will stop the sunroof. Sunshade Operation The sunshade can be opened manually. However, the sunshade will open automatically as the sunroof opens. NOTE: The sunshade cannot be closed if the sunroof is open. Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occur- rence and can be minimized. If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting. If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting or open any window. Sunroof Maintenance Use only a non-abrasive cleaner and a soft cloth to clean the glass panel. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 Ignition OFF Operation The power sunroof switches remain active for up ap- proximately ten minutes after the ignition switch has been turned OFF. Opening either front door will cancel this feature. Sunroof Fully Closed Press the switch forward and release to ensure that the sunroof is fully closed. ELECTRICAL POWER OUTLETS Your vehicle is equipped with 12 Volt (13 Amp) power outlets that can be used to power cellular phones, small electronics and other low powered electrical accessories. The power outlets are labeled with either a “key” or a “battery” symbol to indicate how the outlet is powered. Power outlets labeled with a “key” are powered when the ignition switch is in the ON or ACC position, while the outlets labeled with a “battery” are connected directly to the battery and powered at all times. 138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: • All accessories connected to the “battery” powered outlets should be removed or turned off when the vehicle is not in use to protect the battery against discharge. • To ensure proper operation a MOPAR威 knob and • Do not exceed the maximum power of 160 Watts (13 Amps) at 12 Volts. If the 160 Watt (13 Amp) power rating is exceeded the fuse protecting the system will need to be replaced. element must be used. The front power outlets are located to the left and right of the convenience tray (lower center of instrument panel). Pull lightly on the tab of the plastic cover to access these power outlets. Front Power Outlets The power outlet located on the left side of the tray can be used to power a conventional cigar lighter. The rear power outlet (if equipped) is located in the left rear cargo area. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 WARNING! (Continued) • Do not touch with wet hands. • Close the lid when not in use and while driving • If this outlet is mishandled, it may cause an the vehicle. electric shock and failure. CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting. (Continued) Rear Power Outlet WARNING! To avoid serious injury or death: • Only devices designed for use in this type of outlet should be inserted into any 12 Volt outlet. (Continued) 140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! (Continued) • Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.) will degrade the battery even more quickly. Only use these inter- mittently and with greater caution. • After the use of high power draw accessories, or long periods of the vehicle not being started (with accessories still plugged in), the vehicle must be driven a sufficient length of time to allow the generator to recharge the vehicle’s battery. POWER INVERTER — IF EQUIPPED There is a 115 Volt, 150 Watt inverter outlet located on the back of the center console to convert DC current to AC current. This outlet can power cellular phones, electron- ics and other low power devices requiring power up to 150 Watts. Certain high-end video games, such as Play- station3 and XBox360 will exceed this power limit, as will most power tools. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 The power inverter is designed with built-in overload protection. If the power rating of 150 Watts is exceeded, the power inverter will automatically shut down. Once the electrical device has been removed from the outlet the inverter should automatically reset. If the power rating exceeds approximately 170 Watts, the power inverter may have to be reset manually. To reset the inverter manually press the power inverter button OFF and ON. To avoid overloading the circuit, check the power ratings on electrical devices prior to using the inverter. Power Inverter 142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Press the power inverter switch (located on the upper switch bank) to turn the power on to the outlet. Press the switch again to turn the power off. Power Inverter Switch NOTE: When the power inverter switch is pressed, there will be a delay of approximately one second before the inverter status indicator turns ON. The status indica- tor of the AC power inverter indicates whether the inverter is producing AC power. WARNING! To avoid serious injury or death: • Do not use a three-prong adaptor. • Do not insert any objects into the receptacles. • Do not touch with wet hands. • Close the lid when not in use. • If this outlet is mishandled it may cause an electric shock and failure. CUPHOLDERS There are two cupholders for the front seat passengers located in the center console. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 Front Cupholders The rear passengers have access to two cupholders that pull out from the lower center of the rear seat. CARGO AREA FEATURES Rear Cupholders Cargo Light The cargo area light is activated by opening the liftgate, opening any door, or by rotating the dimmer control on the multifunction lever to the extreme top position. If all doors are closed and only the liftgate is open, pushing on 144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE the cargo light lens surface will turn off all interior lights. Push on the lens surface a second time to restore the interior lights to normal operation. Rear Storage Compartment The rear storage compartment is located on the driver’s side behind the second row seat. Retractable Cargo Area Cover — If Equipped NOTE: The purpose of this cover is for privacy, not to secure loads. It will not prevent cargo from shifting or protect passengers from loose cargo. To cover the cargo area: 1. Grasp the cover at the center handle. Pull it over the cargo area. 2. Insert the pins on the ends of the cover into the slots in the pillar trim cover. 3. The liftgate may be opened with the cargo cover in place. Rear Storage Compartment UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 WARNING! In an accident, a loose cargo cover in the vehicle could cause injury. It could fly around in a sudden stop and strike someone in the vehicle. Do not store the cargo cover on the cargo floor or in the passenger compartment. Remove the cover from the vehicle when taken from its mounting. Do not store it in the vehicle. Rear Cargo Cover 146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Cargo Tie-Down Hooks The cargo tie-downs, located on the cargo area floor, should be used to safely secure loads when the vehicle is moving. Cargo Tie-Down Hooks WARNING! • To help protect against personal injury, passengers should not be seated in the rear cargo area. The rear cargo space is intended for load carrying purposes only, not for passengers, who should sit in seats and use seat belts. • Cargo tie-down hooks are not safe anchors for a child seat tether strap. In a sudden stop or colli- sion, a hook could pull loose and allow the child seat to come loose. A child could be badly injured. Use only the anchors provided for child seat tethers. The weight and position of cargo and passengers can change the vehicle center of gravity and ve- hicle handling. To avoid loss of control resulting in personal injury, follow these guidelines for loading your vehicle: (Continued) WARNING! (Continued) • Do not carry loads which exceed the load limits described on the label attached to the left door or left door center pillar. • Always place cargo evenly on the cargo floor. Put heavier objects as low and as far forward as possible. • Place as much cargo as possible in front of the rear axle. Too much weight or improperly placed weight over or behind the rear axle can cause the rear of the vehicle to sway. • Do not pile luggage or cargo higher than the top of the seatback. This could impair visibility or be- come a dangerous projectile in a sudden stop or collision. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 Cargo Load Floor The panel in the load floor is reversible for added utility. One side is carpeted and the other side features a plastic lined tray which holds a variety of items. Cargo Load Floor The cargo load floor latches should not be 148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The cargo load floor is held by spring loaded latches. In order to use the cargo load floor, use the following procedure: NOTE: used as cargo tie-downs. 1. Flip up the pull loop(s) so they are perpendicular (straight up) to the top surface of the tray. 2. Pull up on the loop(s) and twist 90 degrees, so they are parallel to the slotted hole in the tray. 3. Lift the tray over the loop(s), and reposition the tray. 4. Pull up on the loop(s) and twist 90 degrees, so they are perpendicular (straight up) to the slotted hole in tray. 5. Push the loop(s) back down, so they are parallel to the top of the tray. REAR WINDOW FEATURES Rear Window Wiper/Washer The rear wiper/washer is controlled by a rotary switch located on the control lever. The control lever is located on the right side of the steering column. Rear Wiper/Washer Control Rotate the switch upward to the “On” position to activate the rear wiper. NOTE: The rear wiper operates in an intermittent mode only. Rotate the switch upward to the “washer” position to activate that rear washer. The washer pump will continue to operate as long as the lever or ring is engaged. Upon release, the wipers will cycle two times before returning to the set position. If the rear wiper is operating when the ignition is turned OFF, the wiper will automatically return to the “park” position if power accessory delay is active. Power acces- sory delay can be cancelled by opening the door; if this happens, the rear wiper will stop at its current position and will not go to “park”. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 If the liftgate flipper glass is open, connection to the rear window wiper is interrupted preventing activation of the rear wiper blade. When the liftgate flipper glass is closed, the rear wiper switch, or the ignition switch, needs to be turned OFF and ON to restart the rear wiper. Rear Window Defroster The rear window defroster button is located on the climate control panel. Press this button to turn on the rear window defroster and the heated outside mirrors (if equipped). An indicator in the button will illuminate when the rear window defroster is on. The rear window defroster automatically turns off after approximately 10 minutes. For an additional five minutes of operation, press the button a second time. NOTE: To prevent excessive battery drain, use the rear window defroster only when the engine is operating. 150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Failure to follow these cautions can cause damage to the heating elements: • Use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements. Labels can be peeled off after soaking with warm water. • Do not use scrapers, sharp instruments, or abra- sive window cleaners on the interior surface of the window. • Keep all objects a safe distance from the window. UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 Instrument Panel Features 䡵 Instrument Cluster 䡵 Instrument Cluster Descriptions 䡵 Electronic Vehicle Information Center (EVIC) . . . . . . . . . . . . . . . 154 . . . . . . . . . . . . . . . . . . . . 155 . . . . . . . . . . . 156 . . 166 ▫ Electronic Vehicle Information Center (EVIC) Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . 168 ▫ Trip Functions . . . . . . . . . . . . . . . . . . . . . . 171 ▫ Performance Pages — If Equipped . . . . . . . . 173 ▫ Compass Display . . . . . . . . . . . . . . . . . . . . 177 ▫ Driver-Selectable Surround Sound (DSS) – If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 179 ▫ Personal Settings (Customer-Programmable Features) . . . . . . . . . . . . . . . . . . . . . . . . . . 179 ▫ System Status . . . . . . . . . . . . . . . . . . . . . . . 183 䡵 Media Center 730N/430 (RER/REN/RBZ) — AM/FM Stereo Radio And CD/DVD/HDD/ NAV — If Equipped . . . . . . . . . . . . . . . . . . . . 184 ▫ Operating Instructions — Voice Command System — If Equipped . . . . . . . . . . . . . . . . . 185 152 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Operating Instructions — Uconnect™ phone — If Equipped . . . . . . . . . . . . . . . . . . . . . . 185 ▫ Clock Setting Procedure — RBZ Radio . . . . . 185 ▫ Clock Setting Procedure — RER/REN Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187 䡵 Media Center 130 (RES) — AM/FM Stereo Radio With CD Player (MP3 AUX Jack). . . . . . . 189 ▫ Operating Instructions — Radio Mode . . . . . 189 ▫ Operation Instructions — CD Mode For CD And MP3 Audio Play . . . . . . . . . . . . . . . . . 192 ▫ Notes On Playing MP3 Files . . . . . . . . . . . . 194 ▫ Operation Instructions - Auxiliary Mode . . . . 197 䡵 Media Center 130 (RES/RSC) — AM/FM Stereo Radio With CD Player (MP3 AUX Jack) And Sirius Radio . . . . . . . . . . . . . . . . . . . . . . 198 ▫ Operating Instructions — Radio Mode . . . . . 198 ▫ Operation Instructions — CD Mode For CD And MP3 Audio Play . . . . . . . . . . . . . . . . . 204 ▫ Notes On Playing MP3 Files . . . . . . . . . . . . 206 ▫ List Button (CD Mode For MP3 Play) . . . . . . 209 ▫ Info Button (CD Mode For MP3 Play) . . . . . . 209 䡵 Universal Consumer Interface (UCI) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . . 210 ▫ Connecting The iPod威 . . . . . . . . . . . . . . . . . 211 ▫ Using This Feature . . . . . . . . . . . . . . . . . . . 211 ▫ Controlling The iPod威 Using Radio Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . 211 ▫ Play Mode . . . . . . . . . . . . . . . . . . . . . . . . . 212 ▫ List Or Browse Mode . . . . . . . . . . . . . . . . . 213 䡵 Uconnect™ Multimedia (Satellite Radio) — If Equipped (REN/RER/RBZ/RES Radios Only). . 215 ▫ System Activation . . . . . . . . . . . . . . . . . . . . 215 ▫ Electronic Serial Number/Sirius Identification Number (ESN/SID) . . . . . . . . . 216 ▫ Selecting Uconnect™ Multimedia (Satellite) Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 216 ▫ Satellite Antenna . . . . . . . . . . . . . . . . . . . . . 216 ▫ Reception Quality . . . . . . . . . . . . . . . . . . . . 217 ▫ Operating Instructions - Uconnect™ Multimedia (Satellite) Mode . . . . . . . . . . . . . 217 ▫ Operating Instructions - Uconnect™ phone (If Equipped) . . . . . . . . . . . . . . . . . . . . . . . 219 UNDERSTANDING YOUR INSTRUMENT PANEL 153 䡵 Kicker威 High Performance Sound System With Driver-Selectable Surround (DSS) – If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 220 䡵 Remote Sound System Controls — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 223 ▫ Radio Operation . . . . . . . . . . . . . . . . . . . . . 223 ▫ CD Player . . . . . . . . . . . . . . . . . . . . . . . . . 224 䡵 CD/DVD Disc Maintenance . . . . . . . . . . . . . . 224 䡵 Radio Operation And Cellular Phones . . . . . . . 225 䡵 Climate Controls . . . . . . . . . . . . . . . . . . . . . . 225 ▫ Automatic Temperature Control . . . . . . . . . . 225 ▫ Operating Tips . . . . . . . . . . . . . . . . . . . . . . 232 ▫ Operating Tips Chart . . . . . . . . . . . . . . . . . 234 154 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT PANEL FEATURES 1 — Air Outlet 2 — Instrument Cluster 3 — Radio 4 — Glove Compartment 5 — Upper Switch Bank 6 — Power Outlet/Cigar Lighter 7 — Storage Bin 8 — Power Outlet 9 — Lower Switch Bank 10 — Climate Controls 11 — Ignition Switch 12 — Storage Bin INSTRUMENT CLUSTER UNDERSTANDING YOUR INSTRUMENT PANEL 155 156 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS 1. Speedometer Indicates vehicle speed. 2. Brake Warning Light This light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on, it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the anti-lock brake system reservoir. If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the Brake Booster has been detected by the Anti-Lock Brake System (ABS) / Electronic Stability Program (ESP) sys- tem. In this case, the light will remain on until the condition has been corrected. If the problem is related to the brake booster, the ABS pump will run when applying the brake and a brake pedal pulsation may be felt during each stop. The dual brake system provides a reserve braking capac- ity in the event of a failure to a portion of the hydraulic system. A leak in either half of the dual brake system is indicated by the Brake Warning Light, which will turn on when the brake fluid level in the master cylinder has dropped below a specified level. The light will remain on until the cause is corrected. NOTE: The light may flash momentarily during sharp cornering maneuvers, which change fluid level condi- tions. The vehicle should have service performed, and the brake fluid level checked.

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2010 Jeep Grand Cherokee SRT8 Owners Manual