2004 Hyundai Tiburon Owners Manual

2.

Insert the hexagonal head wrench provided with the vehicle into the socket. This wrench can be found in the vehicle’s trunk or glove box.

3. Push and turn the wrench clockwise to close or counterclockwise to open the sunroof.

CAUTION:

If the sunroof is not reset, it may not be operated normally.

(1)

(2)

(3)

HGK034
(1)Push in the map light switch to turn on the

driver side light.

(2)In the "DOOR" position, the interior courtesy light comes on when any door is opened regardless of the ignition key position. The light goes out gradually 6 seconds after the door is closed.

(3)Push in the map light switch to turn on the

passenger side light.

1FEATURES OF YOUR HYUNDAI SPECTACLE CASE 50

GLOVE BOX

MIRROR

B491A01F-AAT

B500A01A-AAT

B510B01A-AAT OUTSIDE REAR VIEW MIRROR Electric Type (If installed)

HGK036

HGK147

The spectacle case is located on the front overhead console. Push the end of the cover to open or close the spectacle case.

WARNING:

Do not open the spectacle case while the vehicle is moving. The rear view mirror of the vehicle can be blocked by an open spectacle case.

WARNING:

To avoid the possibility of injury in case of an accident or a sudden stop, the glove box door should be kept closed when the car is in motion.

o To open the glove box, pull on the glove box

release lever.

HGK128
The outside rearview mirrors can be adjusted to your preferred rear vision, both directly be- hind the vehicle, and to the rear of the left and right sides. The remote control outside rearview mirror switch controls the adjustments for both the right and left outside mirror.

To adjust the position of either mirror:

1. Move the selecting switch to the right or left to activate the adjustable mechanism for the corresponding door mirror.

2. Next, adjust the mirror angle by depressing the appropriate perimeter switch as illus- trated.

B510D01Y-AAT OUTSIDE REARVIEW MIRROR HEATER (If Installed)

B510C01A-AAT FOLDING THE OUTSIDE REAR VIEW MIRRORS

FEATURES OF YOUR HYUNDAI

51

CAUTION:

o Do not operate the switch continuously

for an unnecessary length of time.

o Scraping ice from the mirror face could cause permanent damage. To remove any ice, use a sponge, soft cloth or approved deicer.

WARNING:

Be careful when judging the size or dis- tance of any object seen in the passenger side rear view mirror. It is a convex mirror with a curved surface. Any objects seen in this mirror are closer than they appear.

A Type

B Type

B380A01GK

B510C01GK

The outside rearview mirror heater is actuated in connection with the rear window defroster. To heat the outside rearview mirror glass, push in the switch for the rear window defroster. The rearview mirror glass will be heated for defrost- ing or defogging and will give you improved rear vision in inclement weather conditions. Push the switch again to turn the heater off. The outside rearview mirror heater automatically turns itself off after 15 minutes.

To fold the outside rear view mirrors, push them toward the rear. The outside rear view mirrors can be folded rearward for parking in narrow areas.

WARNING:

Do not adjust or fold the outside rear view mirrors while the vehicle is moving. This could result in loss of control, and an acci- dent which could cause death, serious in- jury or property damage.

1FEATURES OF YOUR HYUNDAI 52

B520A01A-AAT DAY/NIGHT INSIDE REAR VIEW MIR- ROR

B520B01O-GAT DAY/NIGHT REAR VIEW MIRROR (Electric type) (If installed)

PARKING BRAKE

B530A01A-AAT

B520A01GK

Your Hyundai is equipped with a day/night inside rear view mirror. The "night" position is selected by flipping the tab at the bottom of the mirror toward you. In the "night" position, the glare of headlights of cars behind you is reduced.

Sensor

B520B01GK

The electric type day/night inside rearview mir- ror automatically controls the glare of headlights of the car behind you. Adjust the rearview mirror to the desired position.

HGK178
Always engage the parking brake before leav- ing the car. This also turns on the parking brake indicator light when the key is in the "ON" or "START" position. Before driving away, be sure that the parking brake is fully released and the indicator light is off.

o To engage the parking brake, pull the lever

up as far as possible.

o To release the parking brake, pull up the lever and press the thumb button. Then, while holding the button in, lower the brake lever.

FRONT FOG LIGHT SWITCH

HIGH-MOUNTED REAR STOP LIGHT

B360A01F-AAT (If Installed)

B550A01S-GAT

A Type

B Type

C Type

FEATURES OF YOUR HYUNDAI

FRONT DOOR EDGE WARNING LIGHT B620A01S-AAT

53

HGK142A To turn on the front fog lights, push the switch. They will light when the headlights are turned on.

B550A01GK

In addition to the lower-mounted rear stoplights on either side of the car, the high mounted rear stoplight in the center of the rear window or inserted in the rear spoiler also lights when the brakes are applied.

B620A01GK A red light comes on when the front door is opened. The purpose of this light is to assist when you get in or out and also to warn passing vehicles.

2. Press the safety hook lever up and lift the

hood.

3. Raise the hood by hand.

When closing the hood, slowly close the hood and make sure it locks into place.

WARNING:

o Always double check to be sure that the hood is firmly latched before driving away. If it is not latched, the hood could open while the vehicle is being driven, causing a total loss of visibility, which might result in an accident.

o Do not move the vehicle with the hood in the raised position, as vision is ob- structed and the hood could fall or be damaged.

REMOTE FUEL-FILLER LID RELEASE

B560A02S-AAT

HGK105

The fuel-filler lid may be opened from inside the vehicle by pulling up on the fuel-filler lid opener located on the front floor area on the left side of the car.

1FEATURES OF YOUR HYUNDAI HOOD RELEASE 54

B570A01GK-GAT

Hood Release Lever

HGK106

1. Pull the release knob to unlatch the hood.

HGK098

!

WARNING:

o The fuel cap must be tightened at least 3 clicks, otherwise " " light will illuminate.

o Gasoline vapors are dangerous. Before refueling, always stop the engine and never allow sparks or open flames near the filler area. If you need to replace the filler cap, use a genuine Hyundai re- placement part.

o If you open the fuel filler cap during high ambient temperatures, a slight "pres- sure sound" may be heard. This is nor- mal and not a cause for concern. Whenever you open the fuel filler cap, turn it slowly.

o Make sure the fuel filler cap is replaced and securely seated after fueling. Failure to replace or fully seat the fuel filler cap will result in fuel vapors escaping into the atmosphere and the MIL indicator illuminating.

o Do not "TOP-OFF" after the first nozzle

shut off when refueling.

HGK124Q

NOTE: If the fuel-filler lid will not open because ice has formed around it, tap lightly or push on the lid to break the ice and release the lid. Do not pry on the lid. If necessary, spray around the lid with an approved deicer fluid (do not use radiator anti-freeze) or move the ve- hicle to a warm place and allow the ice to melt.

TAIL GATE

FEATURES OF YOUR HYUNDAI

55

B540A01F-AAT Remote Tail Gate Release

HGK103
To open the tail gate without using the key, pull up the lid release lever located on the driver's door panel. To close, lower the tail gate, then press down on it until it locks. To be sure the tail gate is securely fastened, always try to pull it up again.

WARNING:

The tail gate should always be kept com- pletely closed while the vehicle is in motion. If it is left open or ajar, poisonous exhaust gases may enter the car resulting in serious illness or death to the occupants. See addi- tional warnings concerning exhaust gases on page 2-2.

1FEATURES OF YOUR HYUNDAI 56

B540C01F-AAT To Unlock Using the Key

B540D01GK-GAT when you close the tailgate

WARNING:

Do not close an open tailgate (rear hatch) while a person(s) is sitting upright on the rear seat. The tailgate or tailgate glass may contact the head of a person sitting upright on the rear seat. Closing the tailgate onto a person's head may cause serious injuries, including death.

B540C02GK To open the tail gate, insert the key and turn it clockwise to unlock. The tail gate compartment light illuminates when the tail gate is opened.

HGK226

HGK227

SUN VISOR

B580A01GK-AAT

Vanity mirror

HGK145
Your Hyundai is equipped with sun visors to give the driver and front passenger either frontal or sideward shade. To reduce glare or to shut out direct rays of the sun, turn the sun visor down. A vanity mirror is provided on the back of the sun visor for the front passenger. NOTE: The Supplemental Restraint System (SRS) label containing useful information can be found on the back of each sun visor.

WARNING:

Do not place the sun visor in such a manner that it obscures visibility of the roadway, traffic or other objects.

STEERING WHEEL TILT LEVER

HORN

B600A01HP-AAT (If installed)

B610A01S-AAT

FEATURES OF YOUR HYUNDAI

57

Working Zone

HGK127

To adjust the steering wheel: 1. Pull the lever toward you and hold it to unlock. 2. Raise or lower the steering wheel to the

desired position.

3. After adjustment, release the lever.

Press the pad on the steering wheel to sound the horn.

HGK141

WARNING:

Do not attempt to adjust the steering wheel while driving as this may result in loss of control of the vehicle and serious injury or death.

1FEATURES OF YOUR HYUNDAI 58

LUGGAGE NET

B540D02HP-GAT (if installed) A Type

B Type

HGK241

Some objects can be kept in the net in the luggage compartment. Use the luggage net on the floor(If installed) or at the back of the luggage compartment to prevent objects from sliding.

CAUTION:

To prevent damage to the goods or the vehicle, care should be taken when carrying fragile or bulky objects in the luggage com- partment.

WARNING:

Avoid eye injury. Do not overstretch. Al- ways keep face and body out of recoil path. Do not use when strap has visible signs of wear or damage.

B990A03Y-AAT Floor Mat Anchor

HGK129

When using a floor mat on the front floor carpet, make sure it attaches to the floor mat anchor in your vehicle. This keeps the floor mat from sliding forward.

WARNING:

o Make sure the floor mat is properly placed on the floor carpet. If the floor mat slips and interferes with the movement of the pedals during driving, it may cause an accident.

o Don't put an additional floor mat on the top of the anchored mat, otherwise the additional mat may slide forward and interfere with the movement of the ped- als.

CRUISE CONTROL

B660A01S-AAT (If Installed)

B660B02E-AAT To Set the Cruise Speed

FEATURES OF YOUR HYUNDAI

59

! WARNING:

To avoid accidental cruise control engage- ment, keep the cruise control main switch off when not using the cruise control.

B660A01GK The cruise control system provides automatic speed control for your comfort when driving on freeways, tollroads, or other noncongested highways. This system is designed to function above approximately 25 mph (40 km/h).

B660B01GK 1. Push in the cruise control main switch on the end of the barrel. The "CRUISE" indicator light in the instrument cluster will be illumi- nated. This turns the system on.

2. Accelerate to the desired cruising speed

above 25 mph (40 km/h).

3. Push the control switch downward to "SET

(COAST)" and release it.

4. Remove your foot from the accelerator pedal and the desired speed will automatically be maintained.

5. To increase speed, depress the accelerator pedal enough for the vehicle to exceed the preset speed. When you remove your foot from the accelerator pedal, the vehicle will return to the speed you have set.

1FEATURES OF YOUR HYUNDAI 60

B660C02E-AAT To Cancel the Cruise Speed

B660D01E-AAT To Resume the Preset Speed

B660E01E-AAT To Reset at a Faster Speed

1. Push the control switch upward to "RE-

SUME (ACCEL)" position and hold it.

2. Accelerate to desired speed and release the control switch. While the control switch is held, the vehicle will gradually gain speed.

B660D01GK The vehicle will automatically resume the speed set prior to cancellation when you push the control switch upward to "RESUME (ACCEL)" position and release it, providing the vehicle speed is above 25 mph (40 km/h).

B660F01E-AAT To Reset at a Slower Speed

B660B01GK

1. Push the control switch downward to "SET (COAST)" and hold it. The vehicle will decel- erate.

2. When the desired speed is obtained, release the control switch. While the control switch is pushed, the vehicle speed will gradually decrease.

B660C01GK To disengage the cruise control system,push the control switch "CANCEL". Additionally, the following actions will disengage the system:

o Depress the brake pedal. o Depress the clutch pedal (Manual transaxle). o Shift the selector lever to "N" position (Auto-

matic transaxle).

o Decrease the vehicle speed lower than the

memorized speed by 12 mph (20 km/h).

o Decrease the vehicle speed to less than 25

mph (40 km/h).

o Release the main switch.

FEATURES OF YOUR HYUNDAI

61

WARNING:

o During normal cruise control operation, when the "SET(COAST)" is activated or reactivated after applying the brakes, the cruise control will energize after approximately 3 seconds. This delay is normal.

WARNING:

o Keep the main switch off when not using

the cruise control. Use the cruise control system only when traveling on open highways in good weather.

o Do not use the cruise control when it may not be safe to keep the car at a constant speed, for instance, driving in heavy or varying traffic, or on slippery (rainy, icy or snow-covered) or winding roads or over 6% up-hill or down-hill roads.

o Pay particular attention to the driving conditions whenever using the cruise control system.

o During cruise-control driving with a manual transaxle vehicle, do not shift into neutral without depressing the clutch pedal, or the engine will be overrevved. If this happens, depress the clutch pedal or release the main switch. o With the cruise control engaged, when the brake pedal is applied, it is normal to hear the cruise control system deacti- vate. This is an indication of normal system operation.

1FEATURES OF YOUR HYUNDAI 62

HEATING AND COOLING CONTROL

B710A01GK-GAT

B710A01S-AAT VENTILATION

To operate the ventilation system:

o Set the air intake control to "Fresh" mode

( ).

o To direct all intake air to the dashboard

vents, set the airflow control to "Face".

o Adjust the fan speed control to the desired

o Set the temperature control between "Cool"

speed.

and "Warm".

B710B01S-AAT CENTER VENTILATOR

The center ventilators are located in the middle of the dashboard. The direction of air flow from the vents in the center of the dashboard is adjustable. To control the direction of the air flow, move the knob in the center of the vent up-and-down and side-to-side.

1. Side Defrost Nozzle 2. Side Ventilator 3. Windshield Defrost Nozzle 4. Center Ventilator

HGK001B-1

HEATING AND VENTILATION

FEATURES OF YOUR HYUNDAI

63

B710C02S-AAT SIDE VENTILATOR

B670A01GK-GAT Rotary Type

B670B01A-AAT Fan Speed Control (Blower Control)

The side ventilators are located on each side of the dashboard. To change the direction of the air flow, move the knob in the center of the vent up-and-down and side-to-side. The vents are opened when the vent knob is moved to the up position. The vents are closed when the vent knob is moved to the down position. Keep these vents clear of any obstructions.

HGK002-3

1. Air Conditioning switch 2. Air intake control switch 3. Rear window defroster switch 4. Air flow control switch 5. Fan speed control switch 6. Temperature control switch

HGK006
This is used to turn the blower fan on or off and to select the fan speed. This blower fan speed, and therefore the vol- ume of air delivered from the system, may be controlled manually by setting the blower con- trol between the "1" and "4" positions.

NOTE: If the blower fan is off, the air intake control is set to the fresh mode automatically.

1FEATURES OF YOUR HYUNDAI 64

B670E01A-AAT Temperature Control

B670C01GK-AAT Air Intake Control

Cool

Warm

HGK007

This control is used to adjust the degree of heating or cooling desired.

HGK016
This is used to select fresh outside air or recirculating inside air. To change the air intake control mode, (Fresh mode, Recirculation mode) push the control button.

FRESH MODE ( ) : The indicator light on the button goes off when the air intake control is fresh mode.

RECIRCULATION MODE ( ): The indicator light on the button is illuminated when the air intake control is recirculation mode.

With the "Fresh" mode selected, air enters the vehicle from the outside and is heated or cooled according to the function selected.

With the "Recirculation" mode selected, air from within the passenger compartment will be drawn through the heating system and heated or cooled according to the function selected.

NOTE: o It should be noted that prolonged opera- tion of the heating in "Recirculation" mode will give rise to fogging of the windshield and side windows and the air within the passenger compartment will become stale. In addition, prolonged use of the air conditioning with the "Re- circulation" mode selected may result in the air within the passenger compart- ment becoming excessively dry.

o When the ignition switch is turned "ON" the air intake control will change to "Fresh" mode in floor, floor-defrost and defrost position. This is normal opera- tion. But, the air intake control switch will change to " " mode when the ignition switch is turned "ON" with the MAX A/C mode selected.

B670D04GK-AAT Air Flow Control

FEATURES OF YOUR HYUNDAI

65

HGK005-1
This is used to direct the flow of air. Air can be directed to the floor, dashboard outlets, or windshield. Five symbols are used to represent Face, Bi-Level, Floor, Floor-Defrost and De- frost air position. The MAX A/C mode is used to cool the inside of the vehicle faster.

HGK021

HGK022

Face-Level

Bi-Level

Selecting the "Face" mode will cause air to be discharged through the face level vents.

Air is discharged through the face vents and the floor vents. This makes it possible to have cooler air from the dashboard vents and warmer air from the floor outlets at the same time.

1FEATURES OF YOUR HYUNDAI 66

HGK023

HGK024

HGK025

Floor-Level

Air is discharged through the floor vents, wind- shield defroster nozzle, side defroster nozzle, side ventilator. If the "Floor" mode is selected, the "Fresh" mode will be activated.

Floor-Defrost Level

Defrost-Level

Air is discharged through the windshield defrost nozzle, the floor vents, side defroster nozzle, side ventilator. If the "Floor-Defrost" mode is selected, the A/C will be turn on automatically and "Fresh" mode will be activated.

Air is discharged through the windshield defrost nozzle, side defroster nozzle, side ventilator. If the "Defrost" mode is selected, the A/C will turn on automatically and "Fresh" mode will be activated.

NOTE: If the "Floor-Defrost" or "Defrost" mode is selected, the air conditioning will not turn off by pushing the A/C button. If the air flow control is set to the defrost or the floor-defrost mode, the A/C will be on automatically and the A/C will not off until the air flow control is set to the another

mode except the defrost mode and the floor-defrost mode. Although the A/C switch indicator is turned off, this is normal operation.

HGK021-1

MAX A/C

MAX A/C-Level

Air is discharged through the face level vents. If the "MAX A/C" mode is selected, the A/C will turn on automatically and "Recirculation" mode will be activated.

NOTE: o The air intake control switch will change to " " mode when the ignition switch is turned "ON" with the MAX A/C mode selected.

o When you change to another mode from MAX A/C, the A/C and the air intake control switch are set to the following chart.

Air Intake

Control Switch

or *

A/C

ON

ON or OFF *

ON or OFF *

ON

ON

* The A/C or the air intake control switch

returns to its former setting.

FEATURES OF YOUR HYUNDAI

AIR CONDITIONING SYSTEM

67

B740A01S-AAT Air Conditioning Switch (If installed)

The air conditioning is turned on or off by pushing the A/C button on the heating/air con- ditioning control panel.

HGK018

1FEATURES OF YOUR HYUNDAI 68

B740B01S-AAT Air Conditioning Operation Cooling

HGK002-1
To use the air conditioning to cool the interior:

o Set the temperature control to "Cool". ("Cool" provides maximum cooling. The tempera- ture may be moderated by moving the con- trol toward "Warm".)

o Adjust the fan control to the desired speed. For greater cooling, turn the fan control to one of the higher speeds or temporarily select the "Recirculation" position on the air intake control.

HEATING CONTROLS

B690A02S-AAT For normal heating operation, set the air intake control to the "Fresh" position and the air flow control to "Floor".

For faster heating, the air intake control should be in the "Recirculation" position.

If the windows fog up, move the air flow control to the "Def" (defroster) position. (The A/C will turn on automatically and "Fresh" mode will be activated.)

For maximum heat, move the temperature con- trol to "Warm".

o Turn on the fan control switch. o Turn on the air conditioning switch by push- ing in on the switch. The air conditioning indicator light should come on at the same time.

o Set the air intake control to "Fresh" mode

( ).

DEFROSTING/DEFOGGING

B720A02FC-GAT

A Type

B Type

A Type

B Type

FEATURES OF YOUR HYUNDAI

69

B720A01GK-1

B720A02GK-1

Use the heating/ventilation system to defrost or defog the windshield:

To remove interior fog on the windshield: o Set the air flow control to the defrost ( ) position. (The A/C will turn on automatically and "Fresh" mode will be activated)

o Set the temperature control to the desired position. o Set the fan speed control between "1" and "4" position.

To remove frost or exterior fog on the windshield:

o Set the air flow control to the defrost ( ) position. (The A/C will turn on automatically and "Fresh" mode will be activated.)

o Set the temperature control to warm. o Set the fan speed control to position "3" or "4".

NOTE: When the A/C is operated continuously on the floor-defrost level ( ) or defrost level ( ), it may cause fog to form on the exterior windshield. If this occurs, set the air flow control to the face level position ( ) and fan speed control to the low position.

1FEATURES OF YOUR HYUNDAI 70

B740C01S-AAT Dehumidified Heating

For dehumidified heating:

o Turn on the fan control switch. o Turn on the air conditioning switch. The air conditioning indicator light should come on at the same time.

o Set the air intake control to "Fresh" mode

( ).

o Set the air flow control to "Face". o Adjust the fan control to the desired speed. o For more rapid action, set the fan at one of

the higher speeds.

o Adjust the temperature control to provide the

desired amount of warmth.

B730A01FC-AAT Operation Tips

o To keep dust or unpleasant fumes from entering the car through the ventilation sys- tem, temporarily set the air intake control to "Recirculation". Be sure to return the control to "Fresh" when the irritation has passed to keep fresh air in the vehicle. This will help keep the driver alert and comfortable.

o Air for the heating/cooling system is drawn in through the grilles just ahead of the wind- shield. Care should be taken that these are not blocked by leaves, snow, ice or other obstructions.

o To prevent interior fog on the windshield, set the air intake control to the fresh air ( ) position and fan speed to the desired posi- tion.

AUTOMATIC HEATING AND COOLING CONTROL SYSTEM

B970A01Y-AAT (If lnstalled)

FEATURES OF YOUR HYUNDAI

71

Your Hyundai is equipped with an automatic heating and cooling control system controlled by simply setting the desired temperature.

B970B01GK-GAT Heating and Cooling Controls

TYPE A (Without Air Quality System)

TYPE B (With Air Quality System)

2 3

2 3

10 11

HGK003

1. Temperature Control Button 2. Air Conditioning Switch 3. Display Window 4. Fan Speed Control Switch 5. Air Flow Control Switch 6. AUTO (Automatic Control)Switch

12

7. Defroster Switch 8. OFF Switch 9. Air lntake Control Switch 10.Ambient Temperature Switch 11.Rear Window Defroster Switch 12.Air Quality System Switch (If installed)

10

11

HGK004

1FEATURES OF YOUR HYUNDAI 72

B970C02E-AAT Automatic Operation

NOTE: If the battery has been discharged or dis- connected, the temperature mode will reset to centigrade degrees. This is a normal condition and you can change the temperature mode from centi- grade to farenheit as follows; Press the TEMP button down 3 seconds or more with the button held down. The display shows that the unit of temperature is adjusted to centigrade or fahrenheit. (°C →→→→→ °F or °F →→→→→ °C)

OUTSIDE

TEMP

HGK020

The FATC (Full Automatic Temperature Con- trol) system automatically controls heating and cooling as follows:

1. Push the "AUTO" switch. The indicator light will illuminate confirming that the Face, Floor and/or Bi-Level modes as well as the blower speed and, air conditioner will be controlled automatically.

HGK014

2. Push the "TEMP" button to set the desired

temperature. The temperature will increase to the maxi- mum 90°F(32°C) by pushing on the button. Each push of the button will cause the tem- perature to increase by 1°F(0.5°C). The temperature will decrease to the mini- mum 62°F(17°C) by pushing on the button. Each push of the button will cause the tem- perature to decrease by 1°F(0.5°C).

Photo sensor

G280A01GK

NOTE: Never place anything over the sensor which is located on the instrument panel to en- sure better control of the heating and cool- ing system.

B995A01Y-GAT Ambient Temperature Switch

B980A01Y-AAT MANUAL OPERATION

B980B01Y-AAT Fan Speed Control Switch

FEATURES OF YOUR HYUNDAI

73

The heating and cooling system can be con- trolled manually as well by pushing buttons other than the "AUTO" button. In this state, the system sequentially works according to the order of buttons selected. The function of the buttons which are not se- lected will be controlled automatically. Press the "AUTO" button in order to convert to automatic control of the system.

HGK009

Pressing the button displays the ambient temperature on the display.

OUTSIDE

TEMP

HGK015

The fan speed can be set to the desired speed by pressing the appropriate fan speed control button. The higher the fan speed is, the more air is delivered. Pressing the "OFF" button turns off the fan.

1FEATURES OF YOUR HYUNDAI 74

B670C01GK-AAT Air Intake Control Switch (Without A.Q.S)

With the "Fresh" mode selected, air enters the vehicle from the outside and is heated or cooled according to the function selected.

B980C01GK-GAT Air Intake Control Switch (With A.Q.S) (If Installed)

With the "Recirculation" mode selected, air from within the passenger compartment will be drawn through the heating system and heated or cooled according to the function selected.

NOTE: o It should be noted that prolonged opera- tion of the heating system in "recircula- tion" mode will give rise to fogging of the windshield and side windows and the air within the passenger compartment will become stale. In addition, prolonged use of the air conditioning with the "Re- circulation" mode selected may result in the air within the passenger compart- ment becoming excessively dry.

o When the ignition switch is turned "ON" the air intake control will change to " " mode (regardless of switch position). This is normal operation. The air intake control operates in "AUTO" mode when turning the ignition to the ON position if the "AUTO" mode was used before shut- ting off the engine.

This is used to select fresh outside air or recirculate inside air automatically.

HGK010

: OFF : ON

Fresh mode :

Air enters the vehicle from the outside and is heated or cooled according to the function selected.

HGK008

This is used to select fresh outside air or recirculation inside air. To change the air intake control mode, (Fresh mode, Recirculation mode) push the control button.

FRESH MODE ( ) : The indicator light on the button goes on when the air intake control is in fresh mode.

RECIRCULATION MODE ( ) : The indica- tor light on the button is illuminated when the air intake control is in recirculation mode.

FEATURES OF YOUR HYUNDAI

75

B980E01GK-GAT Air Flow Control

CAUTION:

If the windows fog up with the Recircula- tion or A.Q.S mode selected, set the air intake control to the Fresh air position or A.Q.S control to "OFF".

B980D01Y-AAT Heating and Cooling System Off

Press the "OFF" button to stop the operation of the heating and cooling system.

HGK019

This is used to direct the flow of air. Air can be directed to the floor, dashboard outlets, or windshield. Four symbols are used to represent Face, Bi-Level, Floor and Floor-Defrost air position.

Recirculation mode :

Air from within the passenger compartment will be drawn through the heating system and heated or cooled according to the function selected.

Exhaust gas cutoff mode :

Air enters the vehicle from the outside. But if exhaust gas enters the vehicle from the outside, the exhaust gas cutoff mode ( ) is automatically converted to the mode, to prevent exhaust gas from entering the vehicle.

NOTE: o It should be noted that prolonged opera- tion of the heating system in recircula- tion mode ( ) will give rise to misting of the windshield and side windows and the air within the passenger compart- ment will become stale. In addition, pro- longed use of the air conditioning with the recirculation mode ( ) selected may result in the air within the passenger compartment becoming excessively dry. o When the ignition switch is turned "ON" the air intake control will change to "Fresh ( )" mode (regardless of the switch position). This is normal operation. The air intake control is operated in "AUTO" mode when turning the ignition to the ON position if the "AUTO" mode was used before shutting off the engine.

1FEATURES OF YOUR HYUNDAI 76

Face-Level

Bi-Level

Floor-Level

HGK021

HGK022

HGK023

When selecting the "Face" mode, the indicator light will come on, causing air to be discharged through the face level vents.

When selecting the "Bi-Level" mode, the indica- tor light will come on and the air will be dis- charged through the face vents and the floor vents. This makes it possible to have cooler air from the dashboard vents and warmer air from the floor outlets at the same time.

When selecting the "Floor-Level" mode, the indicator light will come on and the air will be discharged through the floor vents, windshield defroster nozzle, side defroster nozzle, side ventilator.

B980F02E-AAT Defrost Switch

B740D01A-AAT Operation Tips

FEATURES OF YOUR HYUNDAI

77

o If the interior of the car is hot when you first get in, open the windows for a few minutes to expel the hot air.

o When you are using the air conditioning system, keep all windows closed to keep hot air out.

o When moving slowly, as in heavy traffic, shift to a lower gear. This increases engine speed, which in turn increases the speed of the air conditioning compressor.

o On steep grades, turn the air conditioning off to avoid the possibility of the engine over- heating.

o During winter months or in periods when the air conditioning is not used regularly, run the air conditioning once every month for a few minutes. This will help circulate the lubri- cants and keep your system in peak oper- ating condition.

HGK024

Floor-Defrost Level

When selecting the "Floor-Defrost" mode, the indicator light will come on and the air will be discharged through the windshield defrost nozzle, the floor vents, side defroster nozzle, side ventilator.

HGK012
When the "Defrost" button is pressed, the " " mode will be automatically selected and the air will be discharged through the windshield de- frost vents. To assist in defrosting, the air conditioning will operate if ambient temperature is higher than 38.3 °F (3.5 °C) and automatically turns off if the ambient temperature drops below 38.3 °F (3.5 °C).

1FEATURES OF YOUR HYUNDAI 78

AIR CONDITIONER FILTER (IN FRONT OF BLOWER UNIT)

B760A04GK-AAT (If Installed)

Outside air

Inside air

Filter

Inside air

Blower fan

Evaporator core

Heater core

B760A01E

The air conditioner filter is located in front of the blower uniit behind the glove box. It operates to decrease the amount of pollutants entering the car.

CAUTION:

o Replace the filter every 12,000 miles (20,000 km) or once a year. If the car is being driven in severe conditions such as dusty, rough roads, more frequent air conditioner filter inspections and changes are required.

o When the air flow rate is decreased, it must be checked at an authorized dealer. o If your vehicle is not equipped with this filter, it can be installed by your dealer. Check with your dealer for details.

STEREO SOUND SYSTEM

B750A02A-AAT How Car Audio Works FM reception

Ionosphere

AM reception

Ionosphere

FM radio station

Mountains

FEATURES OF YOUR HYUNDAI

79

Unobstructed

area

B750A02L AM broadcasts can be received at greater distances than FM broadcasts. This is because AM radio waves are transmitted at low frequen- cies. These long, low frequency radio waves can follow the curvature of the earth rather than travelling straight out into the atmosphere. In addition, they curve around obstructions so that they can provide better signal coverage.

Buildings

Obstructed area

Iron bridges

B750A03L

FM broadcasts are transmitted at high frequen- cies and do not bend to follow the earth's surface. Because of this, FM broadcasts gen- erally begin to fade at short distances from the station. Also, FM signals are easily affected by buildings, mountains, or other obstructions. These can result in certain listening conditions which might lead you to believe a problem exists with your radio. The following conditions are normal and do not indicate radio trouble:

B750A01L AM and FM radio signals are broadcast from transmitter towers located around your city. They are intercepted by the radio antenna on your car. This signal is then received by the radio and sent to your car speakers. When a strong radio signal has reached your vehicle, the precise engineering of your audio system ensures the best possible quality repro- duction. However, in some cases the signal coming to your vehicle may not be strong and clear. This can be due to factors such as the distance from the radio station, closeness of other strong radio stations or the presence of buildings, bridges or other large obstructions in the area.

1FEATURES OF YOUR HYUNDAI 80

B750B02Y-AAT Using a cellular phone or a two-way radio

When a cellular phone is used inside the vehicle, noise may be produced from the audio equip- ment. This does not mean that something is wrong with the audio equipment. In such a case, use the cellular phone at a place as far as possible from the audio equipment.

B750A04L

B750A05L

o Fading - As your car moves away from the radio station, the signal will weaken and sound will begin to fade. When this occurs, we suggest that you select another stronger station.

o Flutter/Static - Weak FM signals or large obstructions between the transmitter and your radio can disturb the signal causing static or fluttering noises to occur. Reducing the treble level may lessen this effect until the disturbance clears.

o Station Swapping - As an FM signal weak- ens, another more powerful signal near the same frequency may begin to play. This is because your radio is designed to lock onto the clearest signal. If this occurs, select another station with a stronger signal.

o Multi-Path Cancellation - Radio signals being received from several directions can cause distortion or fluttering. This can be caused by a direct and reflected signal from the same station, or by signals from two stations with close frequencies. If this occurs, select another station until the condition has passed.

CAUTION:

When using a communication system such a cellular phone or a radio set inside the vehicle, a separate external antenna must be fitted. When a cellular phone or a radio set is used with an internal antenna alone, it may interfere with the vehicle's electrical system and adversely affect safe operation of the vehicle.

WARNING:

Don't use a cellular phone when you are driving. Stop at a safe place to use a cellular phone.

FEATURES OF YOUR HYUNDAI

81

AUDIO SYSTEM

H260A01O-AAT STEREO RADIO OPERATION (H260) (If installed)

3. BASS/TREBLE Control Knob

4. SCAN Button

6. BAND Selector

2. FADER Control Knob

5. TUNE/SEEK Select Button

7. PRESET Buttons

1. POWER ON-OFF/VOLUME/BALANCE Control Knob

H260A01O

1FEATURES OF YOUR HYUNDAI 82

H260B03E-AAT 1. POWER ON-OFF Control Knob

The radio unit may be operated when the ignition key is in the "ACC" or "ON" position. Press the knob to switch the power on. The LCD shows the radio frequency in the radio mode or the CD track indicator in either the CD mode or CD AUTO CHANGER mode. To switch the power off, press the knob again.

VOLUME Control

Rotate the knob clockwise to increase the volume and turn the knob counterclockwise to reduce the volume.

BALANCE Control

Pull and turn the control knob clockwise to emphasize right speaker sound (left speaker sound will be attenuated). When the control knob is turned counterclockwise, left speaker sound will be emphasized (right speaker sound will be attenuated).

2. FAD (Fader Control) Knob

5. TUNE (Manual) Select Button

Press the ( ) side or ( ) side to increase or to decrease the frequency. Press either button and hold down to continuously scroll. Release button once the desired station is reached.

SEEK Operation (Automatic Channel Selection)

Press the TUNE select button for 1 sec or more. Releasing it will automatically tune to the next available station with a beep sound. When the ( ) side is pressed longer than 1
second, releasing will automatically tune to the next higher frequency and when the ( ) side is pressed longer than 1 second, releasing will automatically tune to the next lower frequency.

Turn the control knob counterclockwise to emphasize front speaker sound (rear speaker sound will be attenuated). When the control knob is turned clockwise, rear speaker sound will be emphasized (front speaker sound will be attenuated).

3. BASS Control Knob

Press to pop the knob out and turn to the left or right for the desired bass tone.

TREB (Treble Control) Knob

Pull the bass control knob further out. Turn to the left or right for the desired treble tone.

4. SCAN Button

When the scan button is pressed, the frequency will increase and the receivable stations will be tuned in one after another, receiving each sta- tion for 5 seconds. To stop scanning, press the scan button again.

FEATURES OF YOUR HYUNDAI

83

CAUTION:

o Do not place beverages close to the audio system. The audio system mecha- nism may be damaged if you spill them. o Do not impact on the audio system, or the audio system mechanism could be damaged.

6. BAND Selector

Pressing the button changes the AM, FM1 and FM2 bands. The mode selected is displayed on LCD.

FM/AM

7. PRESET STATION SELECT Button

Six (6) stations for AM, FM or FM2 respectively can be preset in the electronic memory circuit on this unit.

HOW TO PRESET STATIONS

Six AM and twelve FM stations may be pro- grammed into the memory of the radio. Then, by simply pressing the band select button and/or one of the six station select buttons, you may recall any of these stations instantly. To pro- gram the stations, follow these steps:

o Press band selector to set the band for AM,

FM or FM2.

o Select the desired station to be stored by

seek, scan or manual tuning.

o Determine the preset station select button

you wish to use to access that station.

o Press the station select button for more than two seconds. A select button indicator will show in the display indicating which select button you have depressed. The frequency display will flash after it has been stored into the memory. You should then release the button, and proceed to program the next desired station. A total of 18 stations can be programmed by selecting one AM and two FM stations per button.

o When completed, any preset station may be recalled by selecting AM, FM or FM2 band and the appropriate station button.

1FEATURES OF YOUR HYUNDAI 84

H260B01O-AAT COMPACT DISC PLAYER OPERATION (H260) (If installed)

4. SCAN Button

1. Playing CD

6. EJECT Button

3. TRACK UP/DOWN

2. FF/REW Button

5. REPEAT Button

H260A01O

B260D03O-AAT 1. Playing CD

o Insert the CD with the label facing upward. o Insert the CD to start CD playback, during

radio operation.

o When a disc is in the CD deck, if you press the CD button, the CD player will begin playing even if the radio is being used.

o The CD player can be used when the ignition switch is in either the "ON" or "ACC" position.

2. FF/REW ( / )

If you want to fast forward or reverse through the compact disc track, push and hold the FF ( ) or REW ( ) button. When you release the button, the compact disc player will resume playing.

3. TRACK UP/DOWN

o The desired track on the disc currently being played can be selected using the track number.

o Press once to skip forward to the beginn- ing of the next track. Press once to skip back to the beginning of the track.

4. SCAN Button

o Press the SCAN button to playback the first

10 seconds of each track.

o Press the SCAN button again within 10 sec. When you have reached the desired track.

5. REPEAT Button

o To repeat the track you are currently listen- ing to, press the RPT button. To cancel , press again.

o If you do not release RPT operation when the track ends, it will automatically be replayed. This process will be continued until you push the button again.

6. EJECT Button

When the EJECT button is pressed with a CD loaded, the CD will eject.

FEATURES OF YOUR HYUNDAI

85

NOTE: o If the CD does not operate properly or if the ER2 fault code is displayed, use one of two methods to reset the CD deck function. - Remove the audio fuse for 5 minutes.

Then, reinstall the audio fuse.

- Disconnect the negative terminal of the battery and wait 5 minutes. Then reconnect the negative battery termi- nal.

o To assure proper operation of the unit, keep the vehicle interior temperature within a normal range by using the vehicle’s air conditioning or heating system.

o When replacing the fuse, replace it with

a fuse having the correct capacity.

o The preset station frequencies are all erased when the car battery is discon- nected. Therefore, all data will have to be set again if this should occur.

o Do not add any oil to the rotating parts. Keep magnets, screwdrivers and other metallic objects away from the tape mechanism and head.

o This equipment is designed to be used only in a 12 volt DC battery system with negative ground.

o Do not grip or pull out the disc with your hand while the disc is being pulled into the unit by the self loading mechanism. These can cause poor disc scratching to occur or trouble in the compact disc player.

o Avoid using CD-Recordable or CD- Rewritable as the player could not be operated in recording way of the CD maker. When using the compact disc player, genuine CDs are recommended.

1FEATURES OF YOUR HYUNDAI 86

o This unit is made of precision parts. Do not attempt to disassemble or adjust any parts.

o When driving your vehicle, be sure to keep the volume of the unit set low enough to allow you to hear sounds coming from the outside.

o Do not expose this equipment (includ- ing the speakers) to water or excessive moisture.

CAUTION:

o Do not insert warped or poor quality discs into the CD player as damage to the unit may occur.

o Do not insert anything like coins into the player slot as damage to the unit may occur.

o Do not place beverages close to the audio system. The playback mechanism may be damaged if you spill them.

o Do not impact on the audio system, or the playback mechanism could be dam- aged.

o Driving on the off-roads or other vibra-

tions may skip your compact disc. Do not use the audio system on off- roads as the discs could be scratched and damaged.

B260E01E-AAT CD AUTO CHANGER (H260) (If installed)

6. SCAN Button

1. CD Select Button

3. TRACK UP/DOWN

FEATURES OF YOUR HYUNDAI

87

4. FF/REW Button

5. REPEAT Button

2. DISC Select Button

H260A01O

1FEATURES OF YOUR HYUNDAI 88

B260F01GK-AAT The CD auto changer is located in the right side of the quater trim.

o To use the CD auto changer.

1. Open the sliding lid of the CD auto changer. 2. To eject the compact disc magazine, press the EJECT button located inside the CD auto changer. Insert the discs into the magazine.

3. 4. Push the magazine into the CD auto changer

and close the sliding lid.

o The CD auto changer can be used when the ignition switch is in either the "ON" or "ACC" position.

1. CD Select Button

When the CD changer magazine contains discs, press the "CD" button and the CD changer can be used even if the radio is being used. The Hyundai CD changer can hold up to eight discs. The disc number will be lit, and the track number, and elapsed time will be displayed.

2. DISC Select Button

5. REPEAT

To select the CD you want, push " " to change the disc number.

TUNE DISC

3. TRACK UP/DOWN

o The desired track on the disc currently being played can be selected using the track number.

o Press once to skip forward to the begin- ning of the next track. Press once to skip back to the beginning of the track.

4. FF/REW ( / )

If you want to fast forward or reverse through the compact disc track, push and hold in the FF ( ) or REW ( ) button. When you release the button, the compact disc player will resume playing.

o To repeat the music you are listening to, press the RPT button. To cancel, press again.

o If you do not release RPT operation when the track ends, it will automatically be replayed. This process will be continued until you push the button again.

6. SCAN Button

o Press the SCAN button to playback the first

10 seconds of each track.

o Press the SCAN button again within 10 sec.

for the desired track.

NOTE: o When replacing the fuse, replace it with

a fuse having the correct capacity.

o This equipment is designed to be used only in a 12 volt DC battery system with negative ground.

o This unit is made of precision parts. Do not attempt to disassemble or adjust any parts.

o When driving your vehicle, be sure to keep the volume of the unit set low enough to allow you to hear sounds coming from the outside.

FEATURES OF YOUR HYUNDAI

89

CAUTION:

o Do not insert warped or poor quality discs into the CD changer as damage to the unit may occur.

o Do not insert anything like coins into the changer slot as damage to the unit may occur.

o Do not place beverages close to the audio system. The playback mechanism may be damaged if you spill them.

o Do not impact on the audio system, or the playback mechanism could be dam- aged.

o Driving on the off-roads or other vibra-

tions may skip your compact disc. Do not use the audio system on off- roads as the discs could be scratched and damaged.

o Do not grip or pull out the disc with your hand while the disc is being pulled into the unit by the self loading mechanism. These can cause poor disc scratching to occur or trouble in the compact disc changer.

o Avoid using CD-Recordable or CD- Rewritable as the changer could not be operated in recording way of the CD maker. When using the compact disc changer, genuine CDs are recommended.

1FEATURES OF YOUR HYUNDAI 90

H290A01FC-GAT STEREO RADIO OPERATION (H280) (If installed)

1. POWER ON/OFF VOLUME Control Knob

8. SCAN Button (If installed)

7. EQUALIZER Button

6. BAND Select Button

4. TUNE/SEEK Select Button

H290A01OA

5. PRESET Buttons

2. BASS/BALANCE Control Knob

3. TREBLE/FAD Konb

H290B03E-GAT 1. POWER ON-OFF Control Knob

The radio unit may be operated when the ignition key is in the "ACC" or "ON" position. Press the button to switch the power on. The display shows the radio frequency in the radio mode, the tape direction indicator in the tape mode or CD track in either the CD mode or CD AUTO CHANGER mode. To switch the power off, press the button again.

VOLUME Control

Rotate the knob clockwise to increase the volume and turn the knob counterclockwise to reduce the volume.

2. BASS/BALANCE Control Knob BASS Control Knob

Press to pop the knob out. To increase the bass, rotate the knob clockwise, while to decrease the bass, rotate the knob counterclockwise.

BALANCE Control knob

Pull the Bass control knob out further. Rotate the knob clockwise to emphasize right speaker sound (left speaker sound will be attenuated). When the control knob is turned counterclock- wise, left speaker sound will be emphasized (right speaker sound will be attenuated).

3. TREBLE/FAD Knob TREBLE Control Knob

Press to pop the knob out and turn to the left or right for the desired treble tone.

FAD (Fader Control) Knob

Pull the Treble control knob out further. Turn the control knob counterclockwise to emphasize front speaker sound (rear speaker sound will be attenuated). When the control knob is turned clockwise, rear speaker sound will be empha- sized (front speaker sound will be attenuated).

4. TUNE (Manual) Select Button

Press the ( ) side or ( ) side to increase or to decrease the frequency. Press either button and hold down to continuously scroll. Release button once the desired station is reached.

FEATURES OF YOUR HYUNDAI

91

SEEK Operation (Automatic Channel Selection)

Press the TUNE select button for 0.5 sec or more. Releasing it will automatically tune to the next available station with a beep sound. When the ( ) side is pressed longer than 0.5
second, releasing will automatically tune to the next higher frequency and when the ( ) side is pressed longer than 0.5 second, releasing will automatically tune to the next lower frequency.

5. PRESET STATION Select Buttons

Six (6) stations for AM, FM and FM2 respec- tively can be preset in the electronic memory circuit.

HOW TO PRESET STATIONS

Six AM and twelve FM stations may be pro- grammed into the memory of the radio. Then, by simply pressing the band select button and/or one of the six station select buttons, you may recall any of these stations instantly. To pro- gram the stations, follow these steps:

1FEATURES OF YOUR HYUNDAI 92

o Press band selector to set the band for AM,

FM or FM2.

o Select the desired station to be stored by

seek or manual tuning.

o Determine the preset station select button

you wish to use to access that station.

o Press the station select button for more than two seconds. A select button indicator will show in the display indicating which select button you have depressed. The frequency display will flash after it has been stored into the memory with beep sound. You should then release the button, and proceed to program the next desired station. A total of 18 stations can be programmed by selecting one AM and two FM station per button.

o When completed, any preset station may be recalled by selecting AM, FM or FM2 band and the appropriate station button.

6. BAND Selector

FM/AM

Pressing the button changes the AM, FM1 and FM2 bands. The mode selected is shown on the display.

7. EQUALIZER Button

Press the EQ button to select the CLASSIC, JAZZ, ROCK and DEFEAT MODE for the desired tone quality. Each press of the button changes the display as follows;

CLASSIC → JAZZ → ROCK → DEFEAT

8. SCAN Button (If installed)

When the scan button is pressed, the frequency will increase and the receivable stations will be tuned in one after another, receiving each sta- tion for 5 seconds. To stop scanning, press the scan button again.

CAUTION:

o Do not place beverages close to the audio system. The audio system mecha- nism may be damaged if you spill them. o Do not impact on the audio system, or the audio system mechanism could be damaged.

H290C01FC-GAT CASSETTE TAPE PLAYER OPERATION (H280) (If installed)

FEATURES OF YOUR HYUNDAI

93

5. EQUALIZER Button

4. TAPE EJECT Button

2. AUTO MUSIC Select Button

6. DOLBY Button

1. FF/REW Button

3. TAPE PROGRAM Button

H290A01OA

1FEATURES OF YOUR HYUNDAI 94

H290D02O-GAT 1. FF/REW Button

o Fast forward tape winding starts when the FF ( ) button is pressed during the PLAY or REW mode.

o Tape play starts when the FF ( ) button

is pressed again during the FF mode. o Tape rewinding starts when the REW

( ) button is pressed during the PLAY or FF mode.

o Tape play starts when the REW ( ) button

pressed again during the REW mode.

3. TAPE PROGRAM Button

This allows you to play the reverse side of the tape by merely depressing the program button. An arrow will appear in the display to show tape direction.

4. TAPE EJECT button

o When the button is pressed with the

cassette loaded, the cassette is ejected.

o When the button is pressed during the

FF/REW mode, the cassette is ejected.

2. AUTO MUSIC Select Button

5. EQ Button

Press the button to find the starting point of each song in a prerecorded music tape. The quiet space between songs (must have at least a 4
sec. gap) can be identified by the AUTO MUSIC Select button.

o Pressing the button will play the beginn-

ing of the next music segment.