Download PDF Manual

gear (manual transaxle).


2. Open the hood and remove the engine oil


filler cap.


NOTE: Loosen the oil filter cap by turning it coun- terclockwise to drain well the oil in the oil filter (3.3L only).


HNF5006-1
3. Slide underneath the car and loosen the drain plug by turning it counterclockwise with a wrench of the proper size. Be sure that a drain pan is in position to catch the oil as it drains out, then remove the drain plug.


(3.3L)


WARNING:


Be very careful when draining the engine oil as it may be hot enough to burn you!


4. When the oil has stopped draining, replace the drain plug using a new gasket and re- tighten by turning it clockwise.


Oil pan drain plug tightening torque: 25.3 ~ 32.5 lb.ft (3.5 ~ 4.5 kgf.m)


HNF5005-1


G040B01NF


6 DO-IT-YOURSELF MAINTENANCE


5. Remove the oil filter by turning it counter- clockwise with a oil filter wrench of the proper size. A certain amount of oil will come out when you remove the filter. So be sure to have your drain pan in place underneath it. Install a new oil filter in accordance with the instructions on the carton or on the filter itself. Do not over-tighten.


6.


Tightening torque: 8.7 ~ 11.6 lb.ft (1.2 ~ 1.6 kgf.m)


Be sure that the mounting surface on the engine is clean and that the old gasket is removed completely. Lubricate the new gasket on the filter with clean engine oil before installation.


7. Remove the engine oil level dipstick. 8. Refill the crankcase with the recommended engine oil. Refer to the specification in chap- ter 9 for engine oil capacity.


CAUTION:


Slowly pour the recommended oil into a funnel. Do not overfill to avoid damage to the engine.


9. Start the engine and check to be sure no oil


is leaking from the drain plug or oil filter.


10.Shut off the engine and recheck the oil level.


CHECKING AND CHANGING THE ENGINE COOLANT


G050A01A-AAT


WARNING:


Do not remove the radiator cap when the engine is hot. When the engine is hot, the engine coolant is under pressure and may erupt through the opening if the cap is removed. You could be seriously burned if you do not observe this precaution. Do not remove the radiator cap until the radiator is cool to the touch.


NOTE: Always dispose of used engine oil in an environmentally acceptable manner. It is suggested that it be placed in a sealed container and taken to a service station for reclamation. Do not pour the oil on the ground or put it into the household trash.


PROPOSITION 65 WARNING: This product contains a chemical known to the State of California to cause cancer. Used engine oil may cause irritation or cancer of the skin if left in contact with the skin for prolonged periods of time. Used engine oil contains chemicals that have caused cancer in laboratory animals. Al- ways protect your skin by washing your hands thoroughly with soap and warm water as soon as possible after handling used oil.


G050B01A-AAT Recommended Engine Coolant


G050C01NF-GAT To Check the Coolant Level


G050D01NF-GAT To Change the Engine Coolant


DO-IT-YOURSELF MAINTENANCE


Use a high quality ethylene-glycol coolant in a 50/50 mix with water. The engine coolant should be compatible with aluminum engine parts. Additional corrosion inhibitors or additives should not be used. The cooling system must be maintained with the correct concentration and type of engine coolant to prevent freezing and corrosion. Never allow the concentration of antifreeze to exceed the 60% level or go below the 35% level, or damage to the cooling system may result. For proper concentration when adding or replacing the engine coolant, refer to the following table.


Ambient


Engine Coolant concentration


temperature


°F (°C) 5 (-15) -13 (-25) -31 (-35) -49 (-45)


Antifreeze solution


35% 40% 50% 60%


Water


65% 60% 50% 40%


G050C01NF The coolant level can be seen on the side of the plastic coolant reservoir. The level of the cool- ant should be between the "L" and "F" lines on the reservoir when the engine is warm with it at idle . If the level is below the "L" mark, add engine coolant to bring it up to "F". If the level is low, inspect for coolant leaks and recheck the fluid level frequently. If the level drops again, visit your Hyundai dealer for an inspection and diagnosis of the reason.


The engine coolant should be changed at those intervals specified in the vehicle maintenance schedule in Section 5.


CAUTION:


o Engine coolant can damage the finish of your car. If you spill engine coolant on the car, wash it off thoroughly with clean water.


o The engine in your vehicle has alumi- num engine parts and must be protected by an ethylene-glycol base coolant to prevent corrosion and freezing. Do not use hard water. Hard water can cause engine damage from corrosion, overheating or freezing.


1. Park the car on level ground, set the parking brake and remove the radiator cap when cool.


6 DO-IT-YOURSELF MAINTENANCE 10


HNF5008


2. Wrap a thick cloth around the radiator cap and slowly turn the radiator cap counter- clockwise without pressing down on it, until it stops. This relieves any pressure remain- ing in the cooling system. When you are sure that all the pressure has been released, remove the radiator cap by pushing down and turning counterclockwise.


G050D02NF-A 3. Be sure your drain receptacle is in place. Open the drain cock on the radiator. Allow all the engine coolant to drain from the cooling system, and then securely close the drain cock.


4. Check Section 9 for the capacity of the cooling system in your car. Then, following the manufacturer's directions on the engine coolant container, add the appropriate quan- tity of coolant to the radiator.


5. Slowly fill the radiator with the proper coolant mixture (see the "Recommended Engine Coolant in previous page) until the fluid level stays up in the radiator neck. And pump the radiator hose in order to bleed the air.


G050D01NF 6. Run the engine at idle until the coolant circu- lates. If the cooling fan operates and the coolant starts to circulate, add the coolant to the reservoir.


7. To bleed the air in the cooling system, repeat procedure 6 until the cooling fan operates 3~5 times.


8. Replace the radiator cap and turn it until tightly installed. And then, add coolant to the reservoir until the level is between "L" and "F".


9. Stop the engine and check the coolant level when the engine is cool. The level of the coolant should be the "L" and "F" lines on the reservoir. If the level is below the "L" line, repeat the procedure 4~8 until the level between "L" and "F".


DO-IT-YOURSELF MAINTENANCE


11


CAUTION:


o Operating your vehicle without using a proper air cleaner filter in place can result in excessive engine wear.


o When removing the air cleaner filter, be careful that dust or dirt does not enter the air intake. These may result in dam- age to the air cleaner filter.


10.Replace the reservoir cap and check to be sure the drain cock and the radiator cap are fully closed and not leaking.


CHANGING THE AIR CLEANER FILTER


G070A03Y-AAT


CAUTION:


Recheck after a few days and add the cool- ant if the level is below the "L" level.


WARNING:


The cooling fan is controlled by engine coolant temperature and may sometimes operate even when the engine is not run- ning. Use extreme caution when working near the blades of the coolant fan so that you are not injured by a rotating fan blade. As the engine coolant temperature de- creases, the fan will automatically shut off. This is a normal condition.


HNF5011
The replacement of the air cleaner filter is performed in the following manner.


1. Unsnap the clips around the cover. 2. When this is done, the cover can be lifted off, the old filter removed and the new filter put in its place.


Genuine Hyundai replacement parts are rec- ommended.


6 DO-IT-YOURSELF MAINTENANCE 12


WINDSHIELD WIPER BLADES


G080A02A-AAT


G080A01NF-A The wiper blades should be carefully inspected from time to time and cleaned to remove accu- mulations of road film or other debris. To clean the wiper blades and arms, use a clean sponge or cloth with a mild soap or detergent and water. If the wipers continue to streak or smear the glass, replace them with genuine Hyundai re- placement parts or their equivalent.


CAUTION:


o Do not operate the wipers on dry glass. This can result in more rapid wear of the wiper blades and may scratch the glass. o Keep the blade rubber out of contact with petroleum products such as engine oil, gasoline, etc.


G080B01HR-GAT Replacing the Wiper Blades


To replace the wiper blades, raise the wiper to the vertical position.


To remove the wiper blade


(1)


HHR5048
1. Push down the wiper blade with the locking clip (1) pressed to detach it from the wiper arm.


2. Raise the wiper blade lightly and pull it up.


HHR5049


To install the wiper blade


DO-IT-YOURSELF MAINTENANCE


FILLING THE WASHER RESERVOIR


G090A02NF-AAT (2.4L)


13


HHR5050


1. Put a new wiper blade onto the wiper arm and lower the wiper blade at the level of the wiper arm as shown in the drawing.


2. Pull up the wiper blade until you hear an audible "click" to engage in the end of the wiper arm.


(3.3L)


HHR5051


NOTE: Do not allow the wiper arm to fall against the windshield.


G090A01NF


G090A02NF The washer fluid reservoir supplies fluid to the windshield washer system.


6 DO-IT-YOURSELF MAINTENANCE 14


A good quality washer fluid should be used to fill the washer reservoir. The fluid level should be checked more frequently during bad weather or whenever the washer system is in more fre- quent use. The capacity of the washer reservoir is 3.2 U.S. quarts (4.0 liters).


CAUTION:


o Radiator antifreeze (engine coolant) should not be used in the washer system because it will damage the car's finish. o The washer lever should not be pulled and the washer should not be operated if the washer reservoir is empty. This can damage the washer fluid pump.


WARNING:


o Windshield washer fluid agents contain some amounts of alcohol and can be flammable under certain circumstances. Do not allow sparks or flame to contact the washer fluid or the washer fluid reservoir. Damage to the vehicle or its occupants could occur.


o Windshield washer fluid is poisonous to humans and animals. Do not drink wind- shield washer fluid. Serious injury or death could occur.


WARNING:


It is always better to check the transaxle oil level when the engine is cool or cold. If the engine is hot, you should exercise great caution to avoid burning yourself on hot engine or exhaust parts.


NOTE: It is recommended that the manual transaxle fluid should be checked by an authorized Hyundai Dealer.


CHECKING THE TRANSAXLE OIL (MANUAL)


G100A02NF-AAT


Drain plug


Filler plug


HNF5010
Transaxle lubricant in the manual transaxle should be checked at those intervals specified in the vehicle maintenance schedule in Section 5.


Recommended Oil


Use only HYUNDAI GENUINE PARTS MTF 75W/85 (API GL-4) in the manual transaxle.


Manual Transaxle Oil Capacity


The oil capacity of the manual transaxle is 2.0
U.S. quarts (1.9 liters).


CHECKING THE TRANSAXLE FLUID (AUTOMATIC)


G110A01E-AAT Transaxle fluid in the automatic transaxle should be checked at those intervals specified in the vehicle maintenance schedule in Section 5.


NOTE: Automatic transaxle fluid is basically red in color. As driving distance increases, the fluid color turns darkish red gradually. It is a normal condition and you should not judge the need to replace based upon the changing color. You must replace the automatic transaxle fluid in accordance with intervals specified in the vehicle maintenance schedule in section 5.


G110B05A-AAT Recommended Fluid Your Hyundai automatic transaxle is specially designed to operate with HYUNDAI GENUINE ATF SP III, DIAMOND ATF SP III, SK ATF SP III or other brands meeting the SP III specifica- tion approved by Hyundai Motor Co.. Damage caused by a nonspecified fluid is not covered by your new vehicle limited warranty.


CAUTION:


Use of aftermarket ATF additives may cause damage to the automatic transaxle. Only use HYUNDAI GENUINE ATF SP III, DIAMOND ATF SP III, SK ATF SP III or other brands meeting the SP III specification ap- proved by Hyundai Motor Co.. If you are having your vehicle serviced at a facility other than a Hyundai dealer, verify that the correct ATF is used for your vehicle.


DO-IT-YOURSELF MAINTENANCE


15


G110C01NF-AAT Transaxle Fluid Capacity


The fluid capacity of the automatic transaxle is:


8.24 U.S. quarts (7.8 liters)


11.52 U.S. quarts (10.9 liters)


2.4L


3.3L


WARNING:


The transaxle fluid level should be checked when the engine is at normal operating temperature. This means that the engine, radiator, radiator hose, exhaust system etc., are very hot. Exercise great care not to burn yourself during this procedure.


6 DO-IT-YOURSELF MAINTENANCE 16


G110D03O-AAT Checking the automatic transaxle fluid level


2. After the transaxle is warmed up sufficiently (fluid temperature 70~80°C (158~176°F), for example by 10 minutes usual driving, move the shift lever through all positions then place the selector lever in “N (Neutral) or P (Park)” position.


Fluid level should be within "HOT" range


G110D01NF The automatic transaxle fluid level should be checked regularly. Keep the vehicle on the level ground with the parking brake applied and check the fluid level according to the following procedure. 1. Place the selector lever in N (Neutral) posi- tion and confirm the engine is running at normal idle speed.


G110D02NF 3. Confirm that the fluid level is in “HOT” range on the level gauge. If the fluid level is lower, add the specified fluid from the fill hole. If the fluid level is higher, drain the fluid from the drain hole. If the fluid level is checked in cold condition (fluid temperature 20~30°C (68~86°F) add the fluid to “COLD” line and then recheck the fluid level according to the above step 2.


4.


!


WARNING:


The cooling fan is controlled by engine coolant temperature and may sometimes operate even when the engine is not run- ning. Use extreme caution when working near the blades of the cooling fan so that you are not injured by a rotating fan blade. As the engine coolant temperature de- creases, the fan will automatically shut off. This is a normal condition.


DO-IT-YOURSELF MAINTENANCE


17


G120C02A-AAT Recommended Brake Fluid


Use only hydraulic brake fluid conforming to DOT 3 or DOT 4 specifications in your braking system. Follow the instructions printed on the container.


G120D01A-AAT To Check the Fluid Level


The fluid level in the brake fluid reservoir should be checked periodically. The level should be between the "MIN" and "MAX" marks on the side of the reservoir. If the level is at or below the "MIN" mark, carefully add fluid to bring it up to "MAX". Do not overfill.


CHECKING THE BRAKES


G120A01A-AAT


CAUTION:


Because brakes are essential to the safe operation of the car, it is suggested that they be checked and inspected by your Hyundai dealer. The brakes should be checked and inspected for wear at those intervals specified in the vehicle mainte- nance schedule in Section 5.


G120B01A-AAT Checking the Brake Fluid Level


WARNING:


Use caution when handling brake fluid. It can damage your vision if it gets into your eyes. It will also damage your vehicle's paint if spilled on it and not removed imme- diately.


6 DO-IT-YOURSELF MAINTENANCE 18


AIR CONDITIONING CARE


G120E02A-AAT Adding Brake Fluid


G140A01A-AAT Keeping the Condenser Clean


G140C01A-AAT Lubrication


The air conditioning condenser (and engine radiator) should be checked periodically for accumulation of dirt, dead insects, leaves, etc. These can interfere with maximum cooling ef- ficiency. When removing such accumulations, brush or hose them away carefully to avoid bending the cooling fans.


To lubricate the compressor and the seals in the system, the air conditioning should be run for at least 10 minutes each week. This is particularly important during cool weather when the air conditioning system is not otherwise in use.


G140B01A-AAT Checking the Air Conditioning Opera- tion


1. Start the engine and let it run at a fast idle for several minutes with the air conditioning set at the maximum cold setting. If the air coming out of the in-dash vents is not cold, have the air conditioning system inspected by your Hyundai dealer.


2.


CAUTION:


Running the air conditioning system for extended periods of time with a low refrig- erant level may damage the compressor.


HNF5013


WARNING:


Handle brake fluid carefully. It can damage your vision if it gets into your eyes. Use only DOT 3 or DOT 4 specification fluid from a sealed container. Do not allow the fluid can or reservoir to remain open any longer than required. This will prevent entry of dirt and moisture which can damage the brake sys- tem and cause improper operation.


To add brake fluid, first wipe away any dirt, then unscrew the fluid reservoir cap. Slowly pour the recommended fluid into the reservoir. Do not overfill. Carefully replace the cap on the reser- voir and tighten.


DO-IT-YOURSELF MAINTENANCE


19


3. Lower the glove box down completely by pushing both sides of the glove box inward.


HNF2163


HNF2164
4. Remove the climate control air filter cover by


pressing both side clips.


CAUTION:


Be careful not to damage filter fixing clips.


CHANGING THE CLIMATE CON- TROL AIR FILTER


B145A01NF-AAT (For Evaporator and Blower Unit) (If Installed)


The climate control air filter is located in the right side of the instrument panel. It helps to decrease the amount of pollutants entering the car.


HNF2163-1


1. Remove the cover (1) which is located to the right side of the instrument panel by pulling it.


2. Pull the glove box cylinder (2) to unlock the


glove box retainer.


6 DO-IT-YOURSELF MAINTENANCE 20


CHECKING THE FREE-PLAY


G150A01A-AAT STEERING WHEEL


G160A01A-GAT CLUTCH PEDAL


HNF2165


1.18 in. (30 mm)


0.24~0.51 in. (6~13 mm)


5. Replace the climate control air filter by lifting


6.


it. Installation is the reverse order of disassem- bly.


CAUTION:


To prevent pollutants from entering the car, be sure to properly install the climate con- trol air filter.


HNF5018
To check the steering wheel free-play, stop the car with the wheels pointed straight ahead and gently move the steering wheel back and forth. Use very light finger pressure and be sensitive to changes in resistance that mark the limits of the free-play. If the free-play is greater than specified, have it inspected by your Hyundai dealer and adjusted or repaired if necessary.


G160A01HR With the engine off, press lightly on the clutch pedal until you feel a change in resistance. This is the clutch pedal free-play. The free-play should be within the limits specified in the illus- tration. If it is not, have it inspected by your Hyundai dealer and adjusted or repaired if necessary.


G170A01A-AAT BRAKE PEDAL


CHECKING BRAKE PEDAL CLEARANCE


G180A01A-AAT


DO-IT-YOURSELF MAINTENANCE


CHECKING DRIVE BELTS


G190A02NF-GAT


(2.4L)


Power steering Auto tensioner


21


0.12 ~ 0.31 in. (3 ~ 8 mm)


2.95 in. (75 mm)


Water pump pully


G160A01HR


With the engine off, press down on the brake pedal several times to reduce the vacuum in the brake booster. Then, using your hand, press down slowly on the brake pedal until you feel a change in resistance. This is the brake pedal free-play. The free-play should be within the limits speci- fied in the illustration above. If it is not, have it inspected by your Hyundai dealer and adjusted or repaired if necessary.


G180A01L You need a helper to check the brake pedal clearance. With the engine running, have your helper press down on the brake pedal several times and then hold it down with a force of about 110 lbs (50 kg, 490 N). The brake pedal clear- ance is the distance from the top surface of the brake pedal to the asphalt sheeting under the floor mat. If the brake pedal clearance is not within the limits specified in the illustration, have it in- spected by your Hyundai dealer and adjusted or repaired if necessary.


Generator


COMP


G140D01NF


Generator


Damper pulley


(3.3L)


Water pump pully


Auto tensioner


Power steering


Damper pulley


COMP


G140D02NF


6 DO-IT-YOURSELF MAINTENANCE 22


Drive belts should be checked periodically for proper tension. At the same time, belts should be examined for cracks, wear, fraying or other evidence of deterioration and replaced if neces- sary. When a new belt is replaced, the belt should be located within the pulley of flat idler. Belt routing should also be checked to be sure there is no interference between the belts and other parts of the engine.


NOTE: Drive belt tension is adjusted automatically by the auto tensioner.


CHECKING AND REPLACING FUSES G200A01A-AAT Replacing a Fusible Link


CAUTION:


When replacing a fusible link, never use anything but a new fusible link with the same or lower amperage rating. Never use a piece of wire or a higher-rated fusible link. This could result in serious damage and create a fire hazard.


HNF4004
A fusible link will melt if the electrical circuits from the battery are ever overloaded, thus prevent- ing damage to the entire wiring harness. (This could be caused by a short in the system drawing too much current.) If this ever happens, have a Hyundai dealer determine the cause, repair the system and replace the fusible link. The fusible links are located in a relay box in the engine compartment for easy inspection.


G200B01NF-AAT Replacing Accessory Fuse


2. Open the fuse box and examine each fuse. Remove each fuse by pulling it toward you (a small "fuse puller" tool is contained in the relay and fuse box of the engine room to simplify this operation).


3. Be sure to check all other fuses, even if you


G200B01NF-A


The fuse box for the lights and other electrical accessories will be found on the left side of the instrument panel. Inside the box you will find a list showing the circuits protected by each fuse. If any of your car's lights or other electrical accessories stop working, a blown fuse could be the reason. If the fuse has burned out, you will see that the metal strip inside the fuse has burned through. If you suspect a blown fuse, follow this procedure: 1. Turn off the ignition and all other switches.


G200B02NF


find one that appears to have burned out. 4. Replace the blown fuse by pressing a new fuse of the same rating into place. The fuse should be a snug fit. If it is not, have the fuse clip repaired or replaced by a Hyundai dealer. If you do not have a spare fuse, you may be able to borrow a fuse of the same or lower rating from an accessory you can tempo- rarily get along without (the radio or cigarette lighter, for example). Always remember to replace the borrowed fuse.


DO-IT-YOURSELF MAINTENANCE


23


Good


Burned out


G200B02L


CAUTION:


A burned-out fuse indicates that there is a problem in the electrical circuit. If you re- place a fuse and it blows as soon as the accessory is turned on, the problem is serious and should be referred to a Hyundai dealer for diagnosis and repair. Never re- place a fuse with anything except a fuse with the same or a lower amperage rating. A higher capacity fuse could cause damage and create a fire hazard.


NOTE: See page 6-36 for the fuse panel descrip- tions.


6 DO-IT-YOURSELF MAINTENANCE 24


CHECKING THE BATTERY


G210A01A-AAT


HNF5017


WARNING:


Batteries can be dangerous! When working with batteries, carefully observe the follow- ing precautions to avoid serious injuries.


The fluid in the battery contains a strong solution of sulfuric acid, which is poisonous and highly corrosive. Be careful not to spill it on yourself or the car. If you do spill battery fluid on yourself, immediately do the following:


o If battery fluid is on your skin, flush the affected areas with water for at least 15
minutes and then seek medical assistance. o If battery fluid is in your eyes, rinse out your eyes with water and get medical assistance as soon as possible. While you are being driven to get medical assistance, continue to rinse your eyes by using a sponge or soft cloth saturated with water.


o If you swallow battery fluid, drink a large quantity of water or milk followed by milk of magnesia, eat a raw egg or drink vegetable oil. Get medical assistance as soon as possible.


While batteries are being charged (either by a battery charger or by the vehicle's generator), they produce explosive gases. Always ob- serve these warnings to prevent injuries from occurring:


G210B04A-AAT Checking the Battery


Keep the battery clean. Any evidence of corro- sion around the battery posts or terminals should be removed using a solution of house- hold baking soda and warm water. After the battery terminals are dry, cover them with a light coating of grease.


PROPOSITION 65 WARNING: Battery posts, terminals, and related acces- sories contain lead and lead compounds, chemicals known to the state of California to cause cancer and reproductive harm. Batteries also contain other chemicals known to the state of California to cause cancer. Wash hands after handling.


o Charge batteries only in a well ventilated


o Do not permit flames, sparks or smoking in


area.


the area.


o Keep children away from the area.


!


WARNING: Always read the following in- structions carefully when han- dling a battery.


Keep lighted cigarettes and all other flames or sparks away from the battery.


Hydrogen, which is a highly com- bustible gas, is always present in battery cells and may explode if ignited.


Keep batteries out of the reach of children because batteries con- tain highly corrosive SULFURIC ACID. Do not allow battery acid to contact your skin, eyes, cloth- ing or paint finish.


If any electrolyte gets into your eyes, flush your eyes with clean water for at least 15 minutes and get immediate medical attention. If possible, continue to apply water with a sponge or cloth until medical attention is received.


WARNING: If electrolyte gets on your skin, thoroughly wash the contacted area. If you feel a pain or a burning sensation, get medical attention immediately.


Wear eye protection when charg- ing or working near a battery. Always provide ventilation when working in an enclosed space.


o When lifting a plastic-cased battery, ex- cessive pressure on the case may cause battery acid to leak, resulting in personal injury. Lift with a battery carrier or with your hands on opposite corners.


o Never attempt to charge the battery when


the battery cables are connected.


o The electrical ignition system works with


high voltage. Never touch these components with the engine running or the ignition switched on.


DO-IT-YOURSELF MAINTENANCE


CHECKING ELECTRIC COOLING FANS G220A01A-AAT


25


WARNING:


The cooling fan is controlled by engine coolant temperature and may sometimes operate even when the engine is not run- ning. Use extreme caution when working near the blades of the cooling fan, so that you are not injured by a rotating fan blade. As the engine coolant temperature de- creases the fan will automatically shut off. This is a normal condition.


G220B01NF-GAT Checking Engine Cooling Fan


The engine cooling fan should come on auto- matically if the engine coolant temperature is high or whenever the air conditioning is in operation.


6 DO-IT-YOURSELF MAINTENANCE 26


POWER STEERING FLUID LEVEL


G230A01NF-AAT (2.4L)


FOR MORE INFORMATION ABOUT YOUR HYUNDAI


G250A01A-AAT If you desire additional information about main- taining and servicing your Hyundai, you may purchase a factory Shop Manual at your Hyundai dealer's parts department. This is the same manual used by dealership technicians and while it is highly technical it can be useful in obtaining a better understanding of your car and how it works.


to make certain that the power steering fluid level is between the "MAX" and "MIN" level markings on the fluid reservoir.


NOTE: Grinding noise from the power steering pump may be heard immediately after the engine is started in extremely cold condi- tions (below - 4°F). If the noise stops during warm up, there is no abnormal function in the system. It is due to a power steering fluid characteristic in extremely cold condi- tions.


(3.3L)


G230A01NF


Recommended Fluid Use PSF-4 type fluid


NOTE: Do not start the engine when the power steering oil reservoir is empty.


G240A01A-AAT POWER STEERING HOSES


It is suggested that you check the power steer- ing hose connections for fluid leakage at those intervals specified in the vehicle maintenance schedule in Section 5. The power steering hoses should be replaced if there is severe surface cracking, pulling, scuffing or worn spots. Deterioration of the hose could cause premature failure.


G230A02NF The power steering fluid level should be checked regularly. To check the power steering fluid level, be sure the engine is "OFF", then check


HEADLIGHT AIMING ADJUSTMENT


G290A03O-AAT Before performing aiming adjustment, make sure of the following. 1. Keep all tires inflated to the correct pressure. 2. Place the vehicle on level ground and press the front bumper & rear bumper down sev- eral times. Place vehicle at a distance of 118 in. (3m) from the test wall.


3. See that the vehicle is unloaded (except for full levels of coolant, engine oil and fuel, and spare tire, jack, and tools). Have the driver or equivalent weight placed in driver's seat. 4. Clean the headlight lenses and turn on the


headlights (Low beam).


5. Open the hood.


Vertical aiming


G290A01NF-A


6. Draw a vertical line (through the center of each headlight beam pattern) and a horizon- tal line (through the center of each headlight beam pattern) on the aiming screen. And then, draw a parallel line at 0.8 in. (21
mm) under the horizontal line.


7. Adjust each cut-off line of the low beam to the parallel line with a phillips screwdriver - VERTICAL AIMING.


WARNING:


Never attempt to adjust the horizontal align- ment of your headlights. Horizontal aiming must be adjusted by an authorized Hyundai dealer to avoid incorrect alignment that will reduce the effectiveness of your headlights.


DO-IT-YOURSELF MAINTENANCE


27


G290B01NF-AAT Adjustment After Headlight Assembly Replacement


0.8 in.(21 mm)


Vertical line


Horizontal line


"P"


Cut-off line


Ground line


G260B01GK If the vehicle has had front body repair and the headlight assembly has been replaced, the headlight aiming should be checked using the aiming screen as shown in the illustration. Turn on the headlight switch (Low Beam Position). 1. Adjust headlights so that main axis of light is parallel to the center line of the body and is aligned with point "P" shown in the illustration. 2. Dotted lines in the illustration show the center


of the headlights.


6 DO-IT-YOURSELF MAINTENANCE 28


SPECIFICATION: "H" Horizontal center line of headlights from ground : 26.73 in. (679mm)


"W" Distance between each headlight center : 51.41 in. (1,306mm)


"L" Distance between the headlights and the wall that the lights are tested against : 118.11 in. (3,000 mm)


REPLACEMENT OF LIGHT BULBS


G260A02L-GAT Before attempting to replace a light bulb, be sure the switch is turned to the "OFF" position. The next paragraph shows how to reach the light bulbs so they may be changed. Be sure to replace the burned-out bulb with one of the same number and wattage rating. See page 6-35 for the wattage descriptions.


G270A01NF-AAT HEADLIGHT, FRONT TURN SIGNAL LIGHT AND FRONT FOG LIGHT


Headlight and Front Turn Signal Light


Headlight (High beam)


Headlight (Low beam)


CAUTION:


o Keep the lights out of contact with pe- troleum products, such as oil, gasoline, etc.


o Be sure to replace the LED type equipped


bulbs with an assembly.


o After heavy, driving rain or washing, headlight and taillight lenses could ap- pear frosty. This condition is caused by the temperature difference between the lamp inside and outside. This is similar to the condensation on your windows inside your vehicle during the rain and doesn’t indicate a problem with your vehicle. If the water leaks into the lamp bulb circuitry, have the vehicle checked by an Authorized Hyundai Dealer.


Front Fog Light


Turn signal light (Front position light)


G260A01NF-A


Replacement instructions:


1. Allow the bulb to cool. Wear eye protection. 2. Open the engine hood. 3. Always grasp the bulb by its plastic base,


avoid touching the glass.


DO-IT-YOURSELF MAINTENANCE


29


HNF5026
7. Disconnect the connector from the bulb base in


the back of the headlight.


8. Push the bulb spring to remove the headlight


bulb.


HNF5023
4. Using a socket wrench of the correct size, remove the headlight assembly mounting bolts.


HNF5025
6. Turn the plastic cover counterclockwise


and remove it.


HNF5024
5. Disconnect the power cord from the back of


the headlight.


6 DO-IT-YOURSELF MAINTENANCE 30


Type A


10. Use the protective cap and carton to


promptly dispose of the old bulb. 11. Check for proper headlight aim.


HNF5027


G270A03O


Type B (Low Beam)


HNF5028


12. To replace the front turn signal light bulb (front position light), remove it from the bulb holder and install the new bulb.


OMG075038N 9. Remove the protective cap from the re- placement bulb and install the new bulb by matching the plastic base with the headlight hole. Reattach the bulb spring and recon- nect the connector.


WARNING:


This halogen bulb contains gas under pres- sure and if impacted could shatter, result- ing in flying fragments. Always wear eye protection when servicing the bulb. Protect the bulb against abrasions or scratches and against liquids when lighted. Turn the bulb on only when installing in a headlight. Replace the headlight if damaged or cracked. Keep the bulb out of the reach of children and dispose of the used bulb with care.


Front Fog Light


NOTE: It is recommended that the front fog light bulb should be replaced by an authorized Hyundai dealer.


G270D01NF-AAT REAR COMBINATION LIGHT


Stop/Tail Light, Rear Turn Signal Light, Back-up Light and Rear Side Marker Light


1. Open the trunk lid.


DO-IT-YOURSELF MAINTENANCE


31


HNF5030-A


3. To replace the rear combination light (stop/ tail light, rear side marker light and rear turn signal light), remove it from the bulb holder and install the new bulb.


(1) Stop/tail light (2) Rear side marker light (3) Rear turn signal light


HNF5029


2. Remove the cover on the inside of the rear luggage trim by turning the knob counter- clockwise.


6 DO-IT-YOURSELF MAINTENANCE 32


G270C01L-AAT LUGGAGE COMPARTMENT LIGHT


1. Open the trunk lid.


HNF5042


4. Loosen the mounting screws of the trunk lid trim with a phillips screwdriver and remove the trunk lid trim.


5. To replace the rear combination light (back- up light and stop/tail light), remove the socket by turning it counterclockwise. Install the new bulb.


6.


HNF5031-A


2. Remove the luggage compartment light cover on the rear package tray panel with a flat- head screwdriver.


3. Disconnect the power cord.


HNF5032


4. Replace with a new bulb.


HTB284


G270G01L-AAT INTERIOR LIGHT


G270L01L-AAT MAP LIGHT


DO-IT-YOURSELF MAINTENANCE


33


Screwdriver


HNF5034


2. Replace with a new bulb.


HNF5035


1. Remove the plastic cover with a flat-head


screwdriver.


1. Remove the plastic cover with a flat-head


screwdriver.


G270G01NF


6 DO-IT-YOURSELF MAINTENANCE 34


G270K01L-AAT GLOVE BOX ILLUMINATED LIGHT


1. Open the glove box.


2. Replace with a new bulb.


G270G02NF


Screwdriver


3. Disconnect the power cord.


HJM5039


2. Remove the glove box illuminated light cover


with a flat-head screwdriver.


HNF5036


4. Replace with a new bulb.


HTB284


BULB WATTAGES


G280A01NF-AAT


DO-IT-YOURSELF MAINTENANCE


35


No.


Headlight


Part Name Low beam High beam


Front Turn Signal Light/Front Position Light Map Light Interior Light Front Fog Light Front Side Marker Light Front Door Edge Warning Light


Wattage


Socket Type


55
55
28/8
10
10
27


P x 26d P14,5s BAY15d


w2.1 x 9.5d


sv6-7,6
PGJ13
BAY15d


w2.1 x 4.6d


No. 10
11
12
13
14
15


Part Name


Wattage


Socket Type


Stop / Tail Light High Mounted Rear Stop Light Tail Light Luggage Compartment Light Rear Side Marker Light Rear Turn Signal Light Back-up Light License Plate Light


28/8
16
28/8


27
16


BAY 15d


w2.1 x 9.5d


BAY 15d sv6-7, 6
BAY 15d BAY15s


w2.1 x 9.5d w2.1 x 9.5d


G280A01NF-A


6 DO-IT-YOURSELF MAINTENANCE 36


FUSE PANEL DESCRIPTION


G200C01NF-AAT Engine Compartment


NOTE: Not all fuse panel descriptions in this manual may be applicable to your vehicle. It is accurate at the time of printing. When you inspect the fuse box on your vehicle, refer to the fuse box label.


HNF4005-1


DO-IT-YOURSELF MAINTENANCE


37


DESCRIPTION


FUSE RATING


FUSIBLE


LINK


FUSE


ABS.1
ABS.2
I/P B+1
RR HTD BLOWER P/WDW IGN.2


ECU RLY I/P B+2
IGN.1
ALT MDPS


10
11
12
13
14
15
16
17
18
19
20
21
22
23
24


HORN TAIL ECU IG1
DRL


FR FOG A/CON F/PUMP DIODE ATM STOP


H/LP LO RH


S/ROOF


H/LP WASHER


H/LP HI


ECU


SNSR.3
SNSR.1
SNSR.2


B/UP


IGN COIL ECU (IG1) H/LP LO


ABS


40A 20A 40A 40A 40A 40A 40A 30A 30A 30A 150A 100A 15A 20A 10A 10A 15A 15A 10A 20A


20A 15A 15A 15A 20A 20A 10A 10A 15A 15A 10A 20A 10A 20A 10A


PROTECTED COMPONENTS ABS/ESC control module, Multipurpose check connector ABS/ESC control module, Multipurpose check connector Fuse 23, 24, 30, 31, 32, 33, 34, 35
Defogger relay Blower relay Power window relay, Fuse 16
Start relay, Ignition switch (IG2, START) Engine control unit relay Power connector 1/2, Fuse 21,22
Ignition switch (ACC, IG1) Fusible Iink (ABS. 1, ABS. 2, RR HTD, BLOWER) (Spare) Horn relay Tail light relay PCM (Spare) Siren relay, DRL control module Front fog light relay A/C relay Fuel pump relay (Spare) ATM control relay Stop light relay (Spare) Sunroof control module Headlight washer motor Headlight relay (High) (Spare) Oxygen sensor, Fuel pump relay Mass air flow sensor, Crankshaft/Camshaft position sensor, Oil control valve, SMATRA A/C relay, Cooling fan relay, Injectors Back up light switch, Pulse generator, Vehicle speed sensor Ignition coils, Condenser PCM Headlight relay (Low) ABS/ESC control module, Multipurpose check connector


6 DO-IT-YOURSELF MAINTENANCE 38


G200E01NF-AAT Inner Panel


HNF4003


DO-IT-YOURSELF MAINTENANCE


39


FUSE


FUSE RATING


PROTECTED COMPONENTS


10
11
12
13
14
15
16
17
18
19
20


15A 15A 10A 10A 25A 10A 10A 10A 10A 10A 25A 10A 15A 20A 10A 25A 15A 10A 20A 30A


(Spare) Seat warmer switch BCM(Body Control Module), Sunroof control module, Electronic chrome mirror ESC module, High blower relay, Humidity sensor Cigarette lighter (Spare) Illumination lights, Right : License light, Rear combination light, Headlight, Glove box light Front fog light relay, Left : License light, Rear combination light, Headlight Headlight washer relay, Right headlight leveling actuator DRL control module, Headlight relay, AQS and ambient sensor, Left headlight leveling actuator Wiper and washer A/C control module SRS control module, Passenger's Airbag switch Front accessory socket, Rear power outlet Digital clock, Audio, A/T shift lock control module, Power outside mirror and mirror folding Safety window module (Spare) A/T shift lock control module Power window main switch, Left rear power window switch Power window main switch, Right power window switch


6 DO-IT-YOURSELF MAINTENANCE 40


FUSE


FUSE RATING


PROTECTED COMPONENTS


21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36


POWER CONNECTOR. 1
POWER CONNECTOR. 2


20A 20A 10A 30A 10A 10A 10A 15A 10A 15A 15A 15A 15A 30A 10A 10A 15A 15A


Audio amp Door lock/unlock relay Hazard switch, Hazard relay Power seat manual switch(RHD) Instrument cluster Hazard switch BCM(Body Control Module), Instrument cluster, Yaw rate sensor, ESC switch (Spare) Burglar alarm relay (Spare) Rear fog light relay Trunk lid relay, Fuel filler door and trunk lid switch (Spare) Power seat manual switch Sport mode switch, Key solenoid A/C control module, Outside mirror and mirror folding motor Audio BCM(Body Control Module), Digital clock, Instrument cluster, A/C control module, Courtesy lights


EMISSION CONTROL SYSTEMS


Emission Control System ............................................. 7-2
Catalytic Converter ....................................................... 7-3


7 EMISSION CONTROL SYSTEMS EMISSION CONTROL SYSTEMS


H010A01NF-AAT Your Hyundai is equipped with an emission control system to meet all emission regulations. There are three emission control systems which are as follows.


(1) Crankcase emission control system (2) Evaporative emission control system (3) Exhaust emission control system


In order to assure the proper function of the emission control systems, it is recommended that you have your car inspected and main- tained by an authorized Hyundai dealer in ac- cordance with the maintenance schedule in this manual.


Caution for the Inspection and Maintenance Test (With Electronic Stability Control (ESC) system)


o To prevent the vehicle from misfiring during dynamometer testing, turn the Electronic Stability Control (ESC) sys- tem off by pressing the ESC switch.


o After dynamometer testing is completed, turn the ESC system back on by pressing the ESC switch again.


H010B01A-AAT 1. Crankcase Emission Control System


The positive crankcase ventilation system is employed to prevent air pollution caused by blow-by gases being emitted from the crank- case. This system supplies fresh filtered air to the crankcase through the air intake hose. Inside the crankcase, the fresh air mixes with blow-by gases, which then pass through the PCV valve into the induction system.


H010C01S-AAT 2. Evaporative Emission Control (Includ- ing ORVR: Onboard Refueling Vapor Recovery) System


The Evaporative Emission Control System is designed to prevent fuel vapors from escaping into the atmosphere. (The ORVR system is designed to allow the vapors from the fuel tank to be loaded into a canister while refueling at the gas station, pre- venting the escape of fuel vapors into the atmosphere.)


Canister


Fuel vapors generated inside the fuel tank are absorbed and stored in the onboard canister. When the engine is running, the fuel vapors absorbed in the canister are drawn into the surge tank through the purge control solenoid valve.


Purge Control Solenoid Valve (PCSV)


The purge control solenoid valve is controlled by the Engine Control Module (ECM); when the engine coolant temperature is low during idling, the PCSV closes so that evaporated fuel is not taken into the engine. After the engine warms- up during ordinary driving, the PCSV opens to introduce evaporated fuel to the engine.


H010D01A-AAT 3. Exhaust Emission Control


System


The Exhaust Emission Control System is a highly effective system which controls exhaust emissions while maintaining good vehicle per- formance.


EMISSION CONTROL SYSTEMS


WARNING:


o Remember that your Hyundai dealer is


your best source of assistance.


o Do not stop your Hyundai over any com- bustible material such as grass, paper, leaves or rags. These materials might contact the hot catalytic converter and a fire might result.


CATALYTIC CONVERTER


H020A01A-AAT


Catalytic Converter


H020A01NF


All Hyundai vehicles are equipped with a mono- lith type three-way catalytic converter to re- duce the carbon monoxide, hydrocarbons and nitrogen oxides contained in the exhaust gas. Exhaust gases passing through the catalytic converter cause it to operate at a very high temperature. The introduction of large amounts of unburned gasoline into the exhaust may cause the catalytic converter to overheat and create a fire hazard. This risk may be reduced by observing the following:


WARNING:


o Use unleaded fuel only. o Maintain the engine in good operating condition. Extremely high catalytic con- verter temperatures can result from im- proper operation of the electrical, igni- tion or multiport electronic fuel injec- tion.


o If your engine stalls, pings, knocks, or is hard to start, have your Hyundai dealer inspect and repair the problem as soon as possible.


o Avoid driving with a very low fuel level. Running out of gasoline may cause the engine to misfire and result in damage to the catalytic converter.


o Avoid idling the engine for periods


longer than 10 minutes.


o The vehicle should not be pushed or pulled to get started. This may cause the catalytic converter to overheat and cre- ate a fire hazard.


o Do not touch the catalytic converter or any other part of the exhaust system while the catalytic converter is hot. Shut off the engine, wait for at least one hour before touching the catalytic converter or any other part of the exhaust system.


CONSUMER INFORMATION, REPORTING


SAFETY DEFECTS & BINDING


ARBITRATION OF WARRANTY CLAIMS


Vehicle Identification Number (VIN) .............................. 8-2
Engine Number ............................................................. 8-2
Tire Information ............................................................. 8-2
Recommended Cold Tire Inflation Pressures ............... 8-3
Checking Tire Inflation Pressure ................................... 8-4
Tire Sidewall Labeling ................................................... 8-5
Tire Terminology and Definitions ................................... 8-7
All Season Tires ............................................................ 8-9
Snow Tires .................................................................... 8-9
Tire Chains.................................................................... 8-9
Tire Rotation................................................................ 8-10
Tire Balancing ............................................................. 8-10
Tire Traction ................................................................ 8-11
When to Replace Tires ............................................... 8-11
Tire Maintenance ........................................................ 8-12
Spare Tire and Tools................................................... 8-13
Warranties for Your Hyundai Vehicle .......................... 8-13
Consumer Information ................................................. 8-14
Reporting Safety Defects ............................................ 8-16
Binding Arbitration of Warranty Claims ....................... 8-17


8 CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS


ENGINE NUMBER


VEHICLE IDENTIFICATION NUMBER (VIN)


I010A01O-AAT


I010B01A-AAT (2.4L)


I010A01NF-A The vehicle identification number (VIN) is the number used in registering your car and in all legal matters pertaining to its ownership, etc. It can be found in three different places on your car:


(3.3L)


HNF6003


TIRES


I020A02A-AAT TIRE INFORMATION The tires supplied on your new Hyundai are chosen to provide the best perfor- mance for normal driving. If you ever have questions about your tire warranty and where to obtain ser- vice, see the tire manufacturer's book- let included with your vehicle's Owner's Manual Literature Kit.


1. On the bulkhead between the engine and


passenger compartments.


2. On the left top side of the instrument panel where it can be seen by looking down through the windshield.


3. On the lower side of the center pillar outer


panel.


The engine number is stamped on the engine block as shown in the drawing.


I010B01NF


CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS


I030A03NF-AAT


RECOMMENDED COLD TIRE INFLA- TION PRESSURES


Type A


Type C


Type B


I030A01NF-A Tire label located on the driver's side of the center pillar outer panel gives the cold tire pressures recommended for your vehicle with the original tire size, the number of people that can be in your vehicle and vehicle capacity weight.


I030A03NF-A


i030a05nf-a


These pressures were chosen to pro- vide the most satisfactory combination of ride comfort, tire wear and stability under normal conditions. Tire pressures should be checked at least monthly. Proper tire inflation pressures should be maintained for these reasons:


I030A04NF-A


8 CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS


! WARNING:


o Inspect your tires frequently for proper inflation as well as wear and damage. Always use a tire pressure gauge.


o Tires with too much or too little pressure wear unevenly causing poor handling, loss of vehicle control, and sudden tire failure leading to accidents, injuries, and even death. The recommended cold tire pressure for your vehicle can be found in this manual and on the tire label located on the driver's side of the center pillar. o Worn tires can cause accidents. Replace tires that are worn, show uneven wear, or are damaged. See page 8-11.


o Remember to check the pressure of your spare tire. Hyundai recom- mends that you check the spare every time you check the pressure of the other tires on your vehicle.


NOTE: o Underinflation also results in ex- cessive wear, poor handling and reduced fuel economy. Wheel de- formation also is possible. Keep your tire pressures at the proper levels. If a tire frequently needs refilling, have it checked by your Hyundai Dealer.


o Overinflation produces a harsh ride, excessive wear at the center of the tire tread, and a greater possibility of damage from road hazards.


WARNING:


Overinflation or underinflation can reduce the tire life, adversely affect vehicle handling, and lead to sud- den tire failure. This could rusult in loss of vehicle control and potential injury.


CAUTION:


Always observe the following:


o Check pressures when the tires are cold. (After the vehicle has been parked for at least three hours or hasn't been driven more than 1
mile (1.6 km) since starting up.)


o Check the pressure of your spare tire each time you check the pres- sure of other tires.


o Worn, old tires can cause acci- dents. If your tread is badly worn, or if your tires have been dam- aged, replace them.


CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS


I035A01JM-AAT


CHECKING TIRE INFLATION PRES- SURE Check your tires once a month or more. Also, check the tire pressure of the spare tire.


How to Check Use a good quality gauge to check tire pressure. You cannot tell if your tires are properly inflated simply by looking at them. Radial tires may look properly inflated even when they're underinflated. Check the tire's inflation pressure when the tires are cold. - "Cold" means your vehicle has been sitting for at least three hours or driven no more than 1
mile (1.6 km).


Remove the valve cap from the tire valve stem. Press the tire gauge firmly onto the valve to get a pressure mea- surement. If the cold tire inflation pres- sure matches the recommended pres- sure on the tire and loading information label, no further adjustment is neces- sary. If the pressure is low, add air until you reach the recommended amount. If you overfill the tire, release air by pushing on the metal stem in the center of the tire valve. Recheck the tire pres- sure with the tire gauge. Be sure to put the valve caps back on the valve stems. They help prevent leaks by keeping out dirt and moisture.


I030B01NF-AAT TIRE SIDEWALL LABELING


Loading...
x