2006 Hyundai Sonata Owners Manual

o Never take the car out of gear and coast down a hill. This may be extremely hazard- ous. Always leave the car in gear when moving.

o Do not "ride" the brakes. This can cause them to overheat and malfunction. Instead, when you are driving down a long hill, slow down and shift to a lower gear. When you do this, engine braking will help slow the car. o Slow down before shifting to a lower gear. Otherwise, the lower gear may not be en- gaged.

o Always use the parking brake. Do not de- pend on placing the transaxle in "P" to keep the car from moving.

o Exercise extreme caution when driving on a slippery surface. Be especially careful when braking, accelerating or shifting gears. On a slippery surface, an abrupt change in vehicle speed can cause the drive wheels to lose traction and the vehicle to go out of control. o Optimum vehicle performance and economy is obtained by smoothly depressing and releasing the accelerator pedal.

2 DRIVING YOUR HYUNDAI 12

POWER ADJUSTABLE PEDALS

C100A01NF-AAT (With Automatic Transaxle) (If Installed)

Setting the driver's position

1) Be sure the parking brake is engaged. 2) Move the accelerator and brake pedals to the front most position by pushing the " " portion of the switch.

3) Adjust the seat position and the steering

wheel angle properly.

4) Move the pedals toward you until you can fully depress the brake pedal by pushing the " " portion of the switch.

5) Depress the pedals a few times to get used

to the feel after adjusting.

HNF2115-A

To adjust the position of the accelerator and brake pedals, turn the ignition key to the "ON" position with the selector lever in the "P" position and push the switch.

If you push the " " portion of the switch, the pedals move rearward. If you push the " " portion of the switch, the pedals move forward.

WARNING:

o Adjust the pedals after parking the ve- hicle on level ground. Never attempt to adjust the pedals while the vehicle is moving.

o Never adjust the pedals with your foot on the accelerator pedal as this may result in increasing the engine speed and acceleration.

o Make sure that you can fully depress the brake pedal before driving. Otherwise, you may not be able to hold down the brake pedal firmly in an emergency stop.

ANTI-LOCK BRAKE SYSTEM (ABS)

C120A01NF-AAT The Anti-Lock Brake System (ABS) is designed to prevent wheel lock-up during sudden braking or on hazardous road surfaces. The ABS con- trol module monitors the wheel speed and con- trols the pressure applied to each brake. Thus, in emergency situations or on slick roads, ABS will increase vehicle control during braking.

NOTE: o A click sound may be heard in the engine compartment when the vehicle begins to move after the engine is started. These conditions are normal and indicate that the anti-lock brake system (Electronic Stability Control) is functioning prop- erly.

o During ABS (ESC) operation, a pulsation may be felt in the brake pedal when the brakes are applied. Also, a noise may be heard in the engine compartment while braking. These conditions are normal and indicate that the anti-lock brake system (Electronic Stability Control Sys- tem) is functioning properly.

!

WARNING:

ABS (ESC) will not prevent accidents due to improper or dangerous driving maneuvers. Even though vehicle control is improved during emergency braking, always main- tain a safe distance between you and ob- jects ahead. Vehicle speeds should always be reduced during extreme road condi- tions. The braking distance for cars equipped with an anti-lock braking system (Elec- tronic Stability Control System) may be longer than for those without it in the following road conditions. During these conditions the vehicle should be driven at reduced speeds:

o Rough, gravel or snow-covered roads. o With tire chains installed. o On roads where the road surface is pit-

ted or has different surface height.

The safety features of an ABS (ESC) equipped vehicle should not be tested by high speed driving or cornering. This could endanger the safety of yourself or others.

ELECTRONIC STABILITY CONTROL (ESC) SYSTEM

C310A02NF-AAT

DRIVING YOUR HYUNDAI

13

WARNING:

Never drive too fast for the road conditions or too quickly when cornering. Electronic stability control (ESC) will not prevent ac- cidents. Excessive speed in turns, abrupt maneuvers and hydroplaning on wet sur- faces can still result in serious accidents. Only a safe and attentive driver can prevent accidents by avoiding maneuvers that cause the vehicle to lose traction. Even with ESC installed, always follow all the normal precautions for driving - including driving at safe speeds for the conditions.

B310A01NF-A

The Electronic Stability Control (ESC) system is designed to stabilize the vehicle during cor- nering manuevers. ESC checks where you are steering and where the vehicle is actually going. ESC applies the brakes at individual wheels and intervenes in the engine management system to stabilize the vehicle.

The Electronic Stability Control (ESC) system is an electronic system designed to help the driver maintain vehicle control under adverse conditions. It is not a substitute for safe driving practices. Factors including speed, road con- ditions and driver steering input can all affect whether ESC will be effective in preventing a loss of control. It is still your responsibility to drive and corner at reasonable speeds and to leave a sufficient margin of safety.

2 DRIVING YOUR HYUNDAI 14

CAUTION:

Driving with varying tire or wheel sizes may cause the ESC system to malfunction. When replacing tires, make sure they are the same size as your original tires.

C310B01NF-AAT ESC ON/OFF Mode

C310D01NF-AAT Indicators and Warning

When the ESC is operating, the ESC indicator in the instrument cluster will blink. If you turn the system off by pressing the ESC switch, the ESC-OFF indicator will come on and stay on. In the ESC-OFF mode, the stability control will be deactivated. Adjust your driving accordingly. To turn the system back on, press the switch again. The ESC-OFF indicator should go off.

NOTE: The ESC mode will automatically be turned ON after the engine is turned off and re- started.

The indicators should illuminate when the igni- tion key is turned to ON or START but should go out after three seconds. If the indicators do not illuminate, or the ESC or ESC-OFF indicator does not go out after 3
seconds, have the vehicle checked by an authorized dealer.

Should there be any unusual operation of the device while driving, the ESC-OFF indicator illuminates as a warning. If the ESC-OFF indicator illuminates, drive your car to a safe place and stop the engine. Then, start the engine again to check if the ESC- OFF indicator goes out.

If the indicator remains lit even after the engine has been started, have your car checked by an authorized Hyundai dealer.

GOOD BRAKING PRACTICES

C130A02A-AAT

WARNING:

o Whenever leaving vehicle or parking, always set the parking brake as far as possible and fully engage the vehicle's transaxle into the park position. Ve- hicles not fully engaged in park with the parking brake set are at risk for moving inadvertently and injuring yourself or others.

o All vehicles should always have the park- ing brake fully engaged when parking to avoid inadvertent movement of the car which can injure occupants or pedestri- ans.

o Nothing should be carried on top of the shelf panel behind the rear seat. If there were an accident or a sudden stop, such objects could move forward and cause damage to the vehicle or injure the occu- pants.

DRIVING YOUR HYUNDAI

15

o After being parked, check to be sure the parking brake is not engaged and that the parking brake indicator light is out before driving away.

o Driving through water may get the brakes wet. They can also get wet when the car is washed. Wet brakes can be dangerous! Your car will not stop as quickly if the brakes are wet. Wet brakes may cause the car to pull to one side. To dry the brakes, apply the brakes lightly until the braking action returns to normal, taking care to keep the car under control at all times. If the braking action does not return to normal, stop as soon as it is safe to do so and call your Hyundai dealer for assistance.

o Don't coast down hills with the car out of gear. This is extremely hazardous. Keep the car in gear at all times, use the brakes to slow down, then shift to a lower gear so that engine braking will help you maintain a safe speed. o Don't "ride" the brake pedal. Resting your foot on the brake pedal while driving can be dangerous because it can result in the brakes overheating and losing their effectiveness. It also increases the wear of the brake com- ponents.

o If a tire goes flat while you are driving, apply the brakes gently and keep the car pointed straight ahead while you slow down. When you are moving slowly enough for it to be safe to do so, pull off the road and stop in a safe place.

o If your car is equipped with an automatic transaxle, don't let your car creep forward. To avoid creeping forward, keep your foot firmly on the brake pedal when the car is stopped.

o Use caution when parking on a hill. Farmly engage the parking brake and place the gear selector lever in "P" (automatic transaxle) or in first or reverse gear (manual transaxle). If your car is facing downhill, turn the front wheels into the curb to help keep the car from rolling. If your car is facing uphill, turn the front wheels away from the curb to help keep the car from rolling. If there is no curb or if it is required by other conditions to keep the car from rolling, block the wheels.

o Under some conditions your parking brake can freeze in the engaged position. This is most likely to happen when there is an accumulation of snow or ice around or near the rear brakes or if the brakes are wet. If there is a risk that the parking brake may freeze, apply it only temporarily while you put the gear selector lever in "P" (automatic) or in first or reverse gear (manual transaxle) and block the rear wheels so the car cannot roll. Then release the parking brake.

o Do not hold the vehicle on the upgrade with the accelerator pedal. This can cause the transaxle to overheat. Always use the brake pedal or parking brake.

2 DRIVING YOUR HYUNDAI 16

DRIVING FOR ECONOMY

C140A02A-AAT You can save fuel and get more miles from your car if you follow these suggestions:

o Drive smoothly. Accelerate at a moderate rate. Don't make "jack-rabbit" starts or full- throttle shifts and maintain a steady cruising speed. Don't race between stoplights. Try to adjust your speed to that of the other traffic so you don't have to change speeds unnec- essarily. Avoid heavy traffic whenever pos- sible. Always maintain a safe distance from other vehicles so you can avoid unneces- sary braking. This also reduces brake wear. o Drive at a moderate speed. The faster you drive, the more fuel your car uses. Driving at a moderate speed, especially on the high- way, is one of the most effective ways to reduce fuel consumption.

o Don't "ride" the brake or clutch pedal. This can increase fuel consumption and also increase wear on these components. In addition, driving with your foot resting on the brake pedal may cause the brakes to over- heat, which reduces their effectiveness and may lead to more serious consequences. o Take care of your tires. Keep them inflated to the recommended pressure. Incorrect inflation, either too much or too little, results in unnecessary tire wear. Check the tire pressures at least once a month.

o Be sure that the wheels are aligned cor- rectly. Improper alignment can result from hitting curbs or driving too fast over irregular surfaces. Poor alignment causes faster tire wear and may also result in other problems as well as greater fuel consumption.

o Keep your car in good condition. For better fuel economy and reduced maintenance costs, maintain your car in accordance with the maintenance schedule in Section 5. If you drive your car in severe conditions, more frequent maintenance is required (see Section 5 for details).

o Keep your car clean. For maximum service, your Hyundai should be kept clean and free of corrosive materials. It is especially impor- tant that mud, dirt, ice, etc. not be allowed to accumulate on the underside of the car. This extra weight can result in increased fuel consumption and also contribute to corro- sion.

o Travel lightly. Don't carry unnecessary weight in your car. Weight reduces fuel economy.

o Don't let the engine idle longer than neces- sary. If you are waiting (and not in traffic), turn off your engine and restart only when you're ready to go.

o Remember, your Hyundai does not require extended warm-up. After the engine has started, allow the engine to run for 10 to 20
seconds prior to placing the vehicle in gear. In very cold weather, however, give your engine a slightly longer warm-up period.

o Don't "lug" or "over-rev" the engine. Lugging is driving too slowly in too high a gear result- ing in the engine bucking. If this happens, shift to a lower gear. Over-revving is racing the engine beyond its safe limit. This can be avoided by shifting at the recommended speeds.

o Use your air conditioning sparingly. The air conditioning system is operated by engine power so your fuel economy is reduced when you use it.

SMOOTH CORNERING

WINTER DRIVING

C150A01A-AAT

Avoid braking or gear changing in corners, especially when roads are wet. Ideally, corners should always be taken under gentle accelera- tion. If you follow these suggestions, tire wear will be held to a minimum.

C160A01A-AAT The more severe weather conditions of winter result in greater wear and other problems. To minimize the problems of winter driving, you should follow these suggestions:

C160B01A-AAT Snowy or Icy Conditions

To drive your vehicle in deep snow, it may be necessary to use snow tires or to install tire chains on your tires. If snow tires are needed, it is necessary to select tires equivalent in size and type of the original equipment tires. Failure to do so may adversely affect the safety and handling of your car. Furthermore, speeding, rapid acceleration, sudden brake applications, and sharp turns are potentially very hazardous practices. During deceleration, use engine braking to the fullest extent. Sudden brake applications on snowy or icy roads may cause skids to occur. You need to keep sufficient distance between the vehicle in operation in front and your vehicle. Also, apply the brake gently. It should be noted that installing tire chains on the tire will provide a greater driving force, but will not prevent side skids.

NOTE: Tire chains are not legal in all states. Check state laws before fitting tire chains.

DRIVING YOUR HYUNDAI

17

C160C01A-AAT Use High Quality Ethylene Glycol Coolant

Your Hyundai is delivered with high quality ethylene glycol coolant in the cooling system. It is the only type of coolant that should be used because it helps prevent corrosion in the cool- ing system, lubricates the water pump and prevents freezing. Be sure to replace or replen- ish your coolant in accordance with the main- tenance schedule in Section 5. Before winter, have your coolant tested to assure that its freezing point is sufficient for the temperatures anticipated during the winter.

C160D01A-AAT Check Battery and Cables

Winter puts additional burdens on the battery system. Visually inspect the battery and cables as described in Section 6. The level of charge in your battery can be checked by your Hyundai dealer or a service station.

2 DRIVING YOUR HYUNDAI 18

C160E01A-AAT Change to "Winter Weight" Oil if Necessary

In some climates it is recommended that a lower viscosity "winter weight" oil be used during cold weather. See Section 9 for recommendations. If you aren't sure what weight oil you should use, consult your Hyundai dealer.

C160F01A-AAT Check Spark Plugs and Ignition System

Inspect your spark plugs as described in Sec- tion 6 and replace them if necessary. Also check all ignition wiring and components to be sure they are not cracked, worn or damaged in any way.

C160G01A-AAT To Keep Locks from Freezing

C160I01A-AAT Don't Let Your Parking Brake Freeze

To keep the locks from freezing, squirt an approved de-icer fluid or glycerine into the key opening. If a lock is covered with ice, squirt it with an approved de-icing fluid to remove the ice. If the lock is frozen internally, you may be able to thaw it out by using a heated key. Handle the heated key with care to avoid injury.

C160H02A-AAT Use Approved Window Washer Anti- Freeze in System

To keep the water in the window washer system from freezing, add an approved window washer anti-freeze solution in accordance with instruc- tions on the container. Window washer anti- freeze is available from Hyundai dealers and most auto parts outlets. Do not use engine coolant or other types of anti-freeze as these may damage the paint finish.

Under some conditions your parking brake can freeze in the engaged position. This is most likely to happen when there is an accumulation of snow or ice around or near the rear brakes or if the brakes are wet. If there is a risk the parking brake may freeze, apply it only tempo- rarily while you put the gear selector lever in "P" (automatic) or in first or reverse gear (manual transaxle) and block the rear wheels so the car cannot roll. Then release the parking brake.

C160J01A-AAT Don't Let Ice and Snow Accumulate Underneath

Under some conditions, snow and ice can build up under the fenders and interfere with the steering. When driving in severe winter condi- tions where this may happen, you should peri- odically check underneath the car to be sure the movement of the front wheels and the steering components is not obstructed.

HIGHER SPEED MOTORING

C160K01A-AAT Carry Emergency Equipment

C170A02A-AAT Pre-Trip Inspections

Depending on the severity of the weather where you drive your car, you should carry appropri- ate emergency equipment. Some of the items you may want to carry include tire chains, tow straps or chains, flashlight, emergency flares, sand, a shovel, jumper cables, a window scraper, gloves, ground cloth, coveralls, a blanket, etc.

1. Tires: Adjust the tire inflation pressures to specifica- tion. Low tire inflation pressures will result in overheating and possible failure of the tires. Avoid using worn or damaged tires which may result in reduced traction or tire failure.

NOTE: Never exceed the maximum tire inflation pressure shown on the tires.

DRIVING YOUR HYUNDAI

19

2. Fuel, engine coolant and engine oil: High speed travel consumes more fuel than urban motoring. Do not forget to check both engine coolant and engine oil.

3. Drive belt: A loose or damaged drive belt may result in overheating of the engine.

WARNING:

o Underinflated or overinflated tires can cause poor handling, loss of vehicle control, and sudden tire failure leading to accidents, injuries, and even death. Always check tires are properly inflated before driving. Refer to pages 2-23 and 8-3 for proper tire pressures and further information.

o Driving on tires with no or insufficient tread is dangerous. Worn-out tires can result in loss of vehicle control, colli- sions, injury, and even death. Worn-out tires should be replaced as soon as possible and should never be used for driving. Always check tire tread before driving your car. Refer to 8-10 for further information and tread limits.

2 DRIVING YOUR HYUNDAI USE OF LIGHTS 20

C180A01A-AAT Check your lights regularly for correct opera- tion and always keep them clean. When driving during the day in conditions of poor visibility, it is helpful to drive with headlights on low beam. This enables you to be seen, as well as to see.

TRAILER OR VEHICLE TOWING

C190A01TG-AAT If you are considering towing with your car, you should first check with your State's Department of Motor Vehicles to determine their legal re- quirements. Since laws vary from State to State the require- ments for towing trailers, cars, or other types of vehicles or apparatus may differ. Ask your Hyundai dealer for further details before towing.

CAUTION:

o Do not do any towing with your car during its first 1,200 miles (2,000 km) in order to allow the engine to properly break in. Failure to heed this caution may result in serious engine or transaxle damage.

o When towing a trailer, be sure to consult your Hyundai dealer for further informa- tion on additional requirements such as a towing kit, etc.

C190B01S-AAT Trailer Hitches

Select the proper hitch and ball combination, making sure that its location is compatible with that of the trailer or vehicle being towed. Use a quality non-equalizing hitch which distrib- utes the tongue load uniformly throughout the chassis.

The hitch should be bolted securely to the car and installed by a qualified technician. DO NOT USE A HITCH DESIGNED FOR TEMPORARY INSTALLATION AND NEVER USE ONE THAT ATTACHES ONLY TO THE BUMPER.

C190C01Y-AAT Trailer Brakes

If your trailer is equipped with a braking system, make sure it conforms to federal and/or local regulations and that it is properly installed and operating correctly.

NOTE: If you tow a trailer or vehicle, your car will require more frequent maintenance due to the additional load. See Maintenance Under Severe Usage Conditions" on page 5-6.

!

CAUTION:

o Never connect a trailer brake system

directly to the vehicle brake system.

o When towing a trailer on steep grades (in excess of 12%) pay close attention to the engine coolant temperature gauge to ensure the engine does not overheat. If the needle of the coolant temperature gauge moves across the dial towards "H" (HOT), pull over and stop as soon as it is safe to do so, and allow the engine to idle until it cools down. You may proceed once the engine has cooled sufficiently.

C190D01S-AAT Safety Chains

Should the hitch connection between your car and the trailer or vehicle you are towing fail, the trailer or vehicle could wander dangerously across other lanes of traffic and ultimately leave the roadway. To eliminate this potentially dan- gerous situation, safety chains, attached be- tween your car and the trailer or towed vehicle, are required in most states.

C190E01NF-AAT Trailer Weight Limit

DRIVING YOUR HYUNDAI

21

NOTE: 1. Never load the trailer with more weight in the back than in the front. About 60% of the trailer load should be in the front half on the trailer and the remaining 40% in the rear.

Tongue Load

Total Trailer Weight

C190E01JM o Keep the tongue load 10% of the total trailer

load.

o Tongue load

Total trailer weight

x 100 = 10% (MAX)

o Tongue loads can be increased or de- creased by re-distributing the load in the trailer. This can be verified by checking the total weight of the loaded trailer and then checking the load on the tongue.

Gross Axle Weight

Gross Vehicle

Weight

C190E02JM

2. The total gross vehicle weight with trailer must not exceed the Gross Vehicle Weight Rating (GVWR) shown on the vehicle identification plate (see page 8- 2). The total gross vehicle weight is the combined weight of the vehicle, driver, all passengers and their luggage, cargo, hitch, trailer tongue load and other op- tional equipment.

2 DRIVING YOUR HYUNDAI 22

3. The front or rear axle weight must not exceed the Gross Axle Weight Rating (GAWR) shown on the vehicle identifi- cation plate (see page 8-2). It is possible that your towing package does not ex- ceed the GVWR but exceeds the GAWR. Improper trailer loading and/or too much luggage in the trunk can overload the rear axle. Redistribute the load and check the axle weight again.

CAUTION:

The following specifications are recom- mended when towing a trailer. The loaded trailer weight cannot safely exceed the val- ues in the chart below.

lbs(kg)

Maximum Towable Weight

Trailer

Tongue

3.3L With Brake 2.4L Without Brake

2000 (900) 1500 (675) 1000 (450)

200 (90)

WARNING:

o Improperly loading your vehicle and trailer can seriously affect its steering and braking performance causing a crash which could cause serious injury or death.

o Towing a trailer affects vehicle handling

and braking.

o Drive more slowly when towing a trailer and allow more distance when braking. o Be careful when driving in slippery and

windy conditions.

o Be careful when turning and while driv-

ing up and down hills.

C190F01Y-GAT Trailer or Vehicle Towing Tips

1. Before towing, check hitch and safety chain connections as well as proper operation of the trailer running lights, brake lights, and turn signals.

2. Always drive your vehicle at a moderate

speed. (Less than 60 mph)

3. Trailer towing requires more fuel than normal

conditions.

4. To maintain engine braking efficiency and electrical charging performance, do not tow a trailer with the transaxle in fifth gear (manual transaxle).

5. Always secure items in the trailer to prevent

load shift while driving.

6. Check the condition and air pressure of all tires on the trailer and your car. Low tire pressure can seriously affect the handling. Also check the spare tire.

7. The vehicle/trailer combination is more af-

fected by crosswind and buffeting. When being passed by a large vehicle, keep a constant speed and steer straight ahead. If there is too much wind buffeting, slow down to get out of the other vehicle's air turbulence.

9.

8. When parking your car and trailer, especially on a hill, be sure to follow all the normal precautions. Turn your front wheel into the curb, set the parking brake firmly, and put the transaxle in 1st or Reverse (manual) or Park (automatic). In addition, place wheel chocks at each of the trailer's tires. If the trailer has electric brakes, start your vehicle and trailer moving, and then apply the trailer brake controller by hand to be sure the brakes are working. This lets you check your electrical connection at the same time. 10.During your trip, check occasionally to be sure that the load is secure, and that the lights and any trailer brakes are still working. 11.Avoid jerky starts, sudden acceleration or

sudden stops.

12.Avoid sharp turns and rapid lane changes. 13.Avoid holding the brake pedal down too long or too frequently. This could cause the brakes to overheat, resulting in reduced braking efficiency.

14.When going down a hill, shift into a lower gear

and use the engine braking effect. When ascending a long grade, downshift the transaxle to a lower gear and reduce speed to reduce chances of engine overloading and/or overheating.

15.If you have to stop while going uphill, do not hold the vehicle in place by pressing on the accelerator. This can cause the automatic transaxle to overheat. Use the parking brake or footbrake.

NOTE: When towing check transaxle fluid more frequently.

CAUTION:

If overheating should occur when towing, (the temperature gauge reads near red zone), taking the following action may reduce or eliminate the problem.

1. Turn off the air conditioner. 2. Reduce highway speed. 3. Select a lower gear when going uphill. 4. While in stop and go traffic, place the gear selector in park or neutral and idle the engine at a higher speed.

DRIVING YOUR HYUNDAI

VEHICLE LOAD LIMIT

23

C190F02JM-AAT Tire and Loading Information Label

I030A03NF-A

I030A04NF-A

The tire label located on the driver's side of the center pillar outer panel gives the original tire size, cold tire pressures recommended for your ve-

2 DRIVING YOUR HYUNDAI 24

hicle, the number of people that can be in your vehicle and vehicle capacity weight.

Vehicle capacity weight: 880 lbs (400 kg) Vehicle capacity weight is the maxi- mum combined weight of occupants and cargo. If your vehicle is equipped with a trailer, the combined weight in- cludes the tongue load.

Seating capacity: Total: 5 persons

(Front seat: 2 persons, Rear seat: 3 persons)

Seating capacity is the maximum num- ber of occupants including a driver, your vehicle may carry. However the seating capacity may be reduced based upon the weight of all of the occupants, and the weight of the cargo being car- ried or towed.

Do not overload the vehicle as there is a limit to the total weight, or load limit including occupants and cargo, the vehicle can carry.

Towing capacity: Towing capacity is the maximum trailer weight including its cargo weight, your vehicle can tow. See the section "Trailer or Vehicle Towing" for specifications about the trailer weight.

Cargo capacity: The cargo capacity of your vehicle will increase or decrease depending on the weight and the number of occupants and the tongue load, if your vehicle is equipped with a trailer.

Steps for Determining Correct Load Limit (1)Locate the statement "The combined weight of occupants and cargo should never exceed XXX pounds'' on your vehicle's placard.

(2)Determine the combined weight of the driver and passengers that will be riding in your vehicle.

(3)Subtract the combined weight of the driver and passengers from XXX kilograms or XXX pounds.

(4)The resulting figure equals the avail- able amount of cargo and luggage load capacity. For example, if the "XXX" amount equals 1400 lbs, and there will be five 150 lb. passengers in your vehicle, the amount of avail- able cargo and luggage load capac- ity is 650 lbs. (1400-750 (5 x 150) = 650 lbs.)

(5)Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calcu- lated in Step 4.

(6)If your vehicle will be towing a trailer, load from your trailer will be trans- ferred to your vehicle. Consult this manual to determine how this re- duces the available cargo and lug- gage load capacity of your vehicle.

Example 1

Example 2

DRIVING YOUR HYUNDAI

25

Item

Description

Vehicle Capacity Weight

C190F01JM

Total

1400 lbs

(635 kg)

Item

Description

Vehicle Capacity Weight

C190F02JM

Total

1400 lbs

(635 kg)

Subtract Occupant Weight

300 lbs

150 lbs (68 kg) × 2

Available Cargo and

Luggage Weight

(136 kg)

1100 lbs

(489 kg)

Subtract Occupant Weight

750 lbs

150 lbs (68 kg) x 5

Available Cargo and

Luggage Weight

(340 kg)

650 lbs

(295 kg)

2 DRIVING YOUR HYUNDAI 26

Example 3

Item

Description

Vehicle Capacity Weight

C190F03JM

Total

1400 lbs

(635 kg)

Subtract Occupant Weight

860 lbs

172 lbs (78 kg) x 5

Available Cargo Weight

(390 kg)

540 lbs

(245 kg)

C190G03JM-AAT Compliance Label

Refer to your vehicle's tire and loading information label for specific informa- tion about your vehicle's capacity weight and seating positions. The combined weight of the driver, passengers and cargo should never exceed your vehicle's capacity weight.

C190G01A The compliance label is located on the driver's side of the center pillar outer panel.

The label shows the maximum allow- able weight of the fully loaded vehicle. This is called the GVWR (Gross Ve- hicle Weight Rating). The GVWR in- cludes the weight of the vehicle, all occupants, fuel and cargo.

DRIVING YOUR HYUNDAI

27

WARNING:

o Do not load your vehicle any heavier than the GVWR, either the maximum front or rear GAWR and vehicle capacity weight. If you do, parts, including tires on your ve- hicle can break, and it can change the way your vehicle handles and braking ability. This could cause you to lose control and crash. Also, overloading can shorten the life of your vehicle.

! WARNING:

o Overloading your vehicle can cause heat buildup in your vehicle's tires and possible tire failure that could lead to a crash. o Overloading your vehicle can cause increased stopping dis- tances that could lead to a crash. o A crash resulting from poor han- dling vehicle damage, tire failure, or increased stopping distances could result in serious injury or death.

This label also tells you the maximum weights that can be supported by the front and rear axles, called Gross Axle Weight Rating (GAWR). To find out the actual loads on your front and rear axles, you need to go to a weigh station and weigh your vehicle. Your dealer can help you with this. Be sure to spread out your load equally on the left and right sides of the centerline.

WARNING:

o Never exceed the GVWR for your vehicle, the GAWR for either the front or rear axle and vehicle ca- pacity weight. Exceeding these rat- ings can cause an accident or vehicle damage. You can calcu- late the weight of your load by weighing the items (or people) before putting them in the vehicle. Be careful not to overload your vehicle.

2 DRIVING YOUR HYUNDAI 28

NOTE: o Overloading your vehicle may cause damage. Repairs would not be covered by your warranty. Do not overload your vehicle.

o Using heavier suspension com- ponents to get added durability might not change your weight rat- ings. Ask your dealer to help you load your vehicle the right way.

The label will help you decide how much cargo and installed equipment your vehicle can carry.

If you carry items inside your vehicle – like suitcases, tools, packages, or any- thing else – they move as fast as the vehicle goes. If you have to stop or turn quickly, or if there is a crash, the items will keep going and can cause an injury if they strike the driver or a passenger.

! WARNING:

Items you carry inside your vehicle can strike and injure people in a sudden stop or turn, or in a crash.

o Put things in the cargo area of your vehicle. Try to spread the weight evenly.

o Never stack items, like suitcases, inside the vehicle above the tops of the seats.

o Do not leave an unsecured child

restraint in your vehicle.

o When you carry something inside

the vehicle, secure it.

o Do not drive with a seat folded

down unless necessary.

WHAT TO DO IN AN EMERGENCY

If the Engine Will Not Start ............................................ 3-2
Jump Starting ................................................................ 3-3
If the Engine Overheats ................................................ 3-4
Spare Tire ..................................................................... 3-5
If You Have a Flat Tire .................................................. 3-6
Changing a Flat Tire ...................................................... 3-6
If Your Vehicle Must Be Towed ................................... 3-11
Emergency Towing ..................................................... 3-13

If You Lose Your Keys ................................................ 3-14 3

nfhma-3.p65

1/13/2006, 2:41 PM

3

WHAT TO DO IN AN EMERGENCY

IF THE ENGINE WILL NOT START

D010A01A-AAT

WARNING:

If the engine will not start, do not push or pull the car to start it. This could result in a collision or cause other damage. In addi- tion, push or pull starting may cause the catalytic converter to be overloaded and create a fire hazard.

D010B02A-AAT If Engine Doesn't Turn Over or Turns Over Slowly

D010C02Y-AAT If Engine Turns Over Normally but Does Not Start

1. Check fuel level. 2. With the key in the "OFF" position, check all connectors at ignition, coil and spark plugs. Reconnect any that may be disconnected or loose.

3. Check the fuel line in the engine compart-

4.

ment. If the engine still does not start, call a Hyundai dealer or seek other qualified assistance.

D010D01A-AAT If Engine Stalls While Driving

1. Reduce your speed gradually, keeping a straight line. Move cautiously off the road to a safe place.

2. Turn on your emergency flashers. 3. Try to start the engine again. If your vehicle will not start, contact a Hyundai dealer or seek other qualified assistance.

1.

HNF5017
If your car has an automatic transaxle, be sure the gear selector lever is in "N" or "P" and the emergency brake is set.

2. Check the battery connections to be sure

they are clean and tight.

3. Turn on the interior light. If the light dims or goes out when you operate the starter, the battery is discharged.

4. Check the starter connections to be sure

they are securely tightened.

5. Do not push or pull the vehicle to start it. See

instructions for "Jump Starting".

nfhma-3.p65

1/13/2006, 2:41 PM

JUMP STARTING

D020A03A-AAT

Discharged battery

Booster battery

HNF4001

WARNING:

The gas produced by the battery during the jump-start operation is highly explosive. If these instructions are not followed exactly, serious personal injury and damage to the vehicle may occur! If you are not sure how to follow this procedure, seek qualified assistance. Automobile batteries contain sulfuric acid. This is poisonous and highly corrosive. When jump starting, wear pro- tective glasses and be careful not to get acid on yourself, your clothing or on the car.

o If you should accidentally get acid on your skin or in your eyes, immediately remove any contaminated clothing and flush the area with clean water for at least 15 minutes. Then promptly obtain medical attention. If you must be transported to an emergency facil- ity, continue to apply water to the affected area with a sponge or cloth.

o The gas produced by the battery during the jump-start operation is highly explosive. Do not smoke or allow a spark or an open flame in the vicinity.

o The battery being used to provide the jump start must be 12-volt. If you cannot deter- mine that it is a 12-volt battery, do not attempt to use it for the jump start.

o To jump start a car with a discharged battery,

follow this procedure exactly:

1.

If the booster battery is installed in another vehicle, be sure the two vehicles are not touching.

2. Turn off all unnecessary lights and acces-

sories in both vehicles.

3. Attach the clamps of the jumper cable in the exact location shown on the illustration. First, attach one clamp of the jumper cable to the positive (+) post or cable of the discharged battery.

WHAT TO DO IN AN EMERGENCY

Then attach the other end of the same cable to the positive (+) post or cable of the booster battery. Next, using the other cable, attach one clamp to the negative (-) post or cable of the booster battery. Then attach the other end of that cable to a solid metal part of the engine of the vehicle with the discharged battery away from the battery. Do not con- nect the cable to any moving part.

4. Start the engine in the car with the booster battery and let it run for a few minutes. This will help to assure that the booster battery is fully charged. During the jumping operation, run the engine in this vehicle at about 2,000
rpm.

5. Start the engine in the car with the dis- charged battery using the normal starting procedure. After the engine starts, leave the jumper cables connected and let the engine run at fast idle or about 2,000 rpm for several minutes.

6. Carefully remove the jumper cables in the

reverse order of attachment.

If you do not know why your battery became discharged (because the lights were left on, etc.), have the charging system checked by your Hyundai dealer.

nfhma-3.p65

1/13/2006, 2:41 PM

3

WHAT TO DO IN AN EMERGENCY

IF THE ENGINE OVERHEATS

D030A02A-AAT If your temperature gauge indicates overheat- ing, you experience a loss of power, or hear loud pinging or knocking, the engine is probably too hot. If this happens, you should:

1. Pull off the road and stop as soon as it is safe

to do so.

3.

2. Place the gear selector lever in "P" (auto- matic) or neutral (manual transaxle) and set the parking brake. If the air conditioning is on, turn it off. If engine coolant is running out under the car or steam is coming out from the hood, stop the engine. Do not open the hood until the coolant has stopped running or the steaming has stopped. If there is no visible loss of engine coolant and no steam, leave the engine running and check to be sure the engine cooling fan is operating. If the fan is not running, turn the engine off.

4. Check to see if the water pump drive belt is missing. If it is not missing, check to see that it is tight. If the drive belt seems to be satisfactory, check for coolant leaking from the radiator, hoses or under the car. (If the air conditioning had been in use, it is normal for cold water to be draining from it when you stop).

WARNING:

While the engine is running, keep hair, hands and clothing away from moving parts such as the fan and drive belts to prevent injury.

5.

If the water pump drive belt is broken or engine coolant is leaking out, stop the engine immediately and call the nearest Hyundai dealer for assistance.

WARNING:

Do not remove the radiator cap when the engine is hot. This can allow coolant to be blown out of the opening and cause seri- ous burns.

6.

If you cannot find the cause of the overheat- ing, wait until the engine temperature has returned to normal. Then, if coolant has been lost, carefully add coolant to the reservoir (page 6-9) to bring the fluid level in the reservoir up to the halfway mark.

7. Proceed with caution, keeping alert for fur- ther signs of overheating. If overheating happens again, call a Hyundai dealer for assistance.

CAUTION:

Serious loss of coolant indicates there is a leak in the cooling system and this should be checked as soon as possible by a Hyundai dealer.

nfhma-3.p65

1/13/2006, 2:41 PM

WHAT TO DO IN AN EMERGENCY

WARNING:

The temporary spare tire is for emer- gency use only. Do not operate your vehicle on this temporary spare at speeds over 50 mph (80 kmh). The original tire should be repaired or replaced as soon as is possible to avoid failure of the spare possibly leading to personal injury or death.

SPARE TIRE

D040A03GK-AAT

TEMPORARY SPARE TIRE The following instructions for the tem- porary spare tire should be observed:

1. Check inflation pressure as soon as practical after installing the spare tire, and adjust to the specified pres- sure. The tire pressure should be periodically checked and maintained at the specified pressure while the tire is stored.

Spare Tire Pressure

Tire Size Inflation Pressure

T125/80 D16
420 KPA(60 PSI)

2. The spare tire should only be used temporarily and should be returned to the luggage compartment as soon as the original tire can be repaired or replaced.

3. Continuous use at speeds of over 50
mph (80 km/h) is not recommended.

4. As the temporary spare tire is spe- cifically designed for your car, it should not be used on any other vehicle.

5. The temporary spare tire should not be used on any other wheels, nor should standard tires, snow tires, wheel covers or trim rings be used with the temporary spare wheel. If such use is attempted, damage to these items or other car components may occur.

6. The temporary spare tire pressure should be checked once a month while the tire is stored.

CAUTION:

o Do not use snow chains with your

temporary spare tire.

o Do not use more than one tempo-

rary spare tire at a time.

o Do not tow a trailer while the tem-

porary spare tire is installed.

nfhma-3.p65

1/13/2006, 2:41 PM

WHAT TO DO IN AN EMERGENCY

IF YOU HAVE A FLAT TIRE

CHANGING A FLAT TIRE

D040B01NF-GAT

Handling the Spare Tire

D050A01A-AAT If a tire goes flat while you are driving:

D060A01A-AAT

HNF4008
To remove the spare tire, take out the tool receptacle and remove the installa- tion bolt by turning it counterclockwise. To replace the spare tire in its storage compartment, tighten the bolt firmly with your fingers until there is no more play in the spare tire.

1. Take your foot off the accelerator pedal and let the car slow down while driving straight ahead. Do not apply the brakes immediately or attempt to pull off the road as this may cause a loss of control. When the car has slowed to such a speed that it is safe to do so, brake carefully and pull off the road. Drive off the road as far as possible and park on firm, level ground. If you are on a divided highway, do not park in the median area between the two traffic lanes.

2. When the car is stopped, turn on your emergency hazard flashers, set the parking brake and put the transaxle in "P" (automatic) or reverse (manual transaxle).

3. Have all passengers get out of the car. Be sure they all get out on the side of the car that is away from traffic.

4. Change the tire according to the in-

structions provided as follows.

D060A01NF-A The procedure described on the follow- ing pages can be used to rotate tires as well as to change a flat tire. When preparing to change a flat tire, check to be sure the gear selector lever is in "P" (automatic transaxle) or reverse gear (manual transaxle) and that the parking brake is set, then:

nfhma-3.p65

1/13/2006, 2:41 PM

D060B01NF-GAT

1. Obtain Spare Tire and Tool

D060C01A-AAT

2. Block the Wheel

D060D01A-AAT

3. Loosen Wheel Nuts

Flat tire

WHAT TO DO IN AN EMERGENCY

D060B01NF-A Take out the tool receptacle and turn the installation bolt counterclockwise to remove spare tire from the trunk.

HNF4009
Block the wheel that is diagonally oppo- site from the flat to keep the vehicle from rolling when the car is raised on the jack.

HNF4011-A The wheel nuts should be loosened slightly before raising the car. To loosen the nuts, turn the wrench handle coun- terclockwise. When doing this, be sure that the socket is seated completely over the nut so it cannot slip off. For maximum leverage, position the wrench so the handle is to the left as shown in the drawing. Then, while holding the wrench near the end of the handle, push down on it with steady pressure. Do not remove the nuts at this time. Just loosen them about one-half turn.

nfhma-3.p65

1/13/2006, 2:41 PM

WHAT TO DO IN AN EMERGENCY

D060E01A-AAT

4. Put the Jack in Place

D060F02E-AAT

5. Raising the Car

D060E01NF-A The base of the jack should be placed on firm, level ground. The jack should be positioned as shown in the drawing.

Wheel nut wrench

Wrench bar

HNF4025
After inserting a wrench bar into the wheel nut wrench, install the wrench bar into the jack as shown in the drawing. To raise the vehicle, turn the wheel nut wrench clockwise. As the jack begins to raise the vehicle, double check that it is properly positioned and will not slip. If the jack is on soft ground or sand, place a board, brick, flat stone or other object under the base of the jack to keep it from sinking.

Raise the car high enough so that the fully inflated spare tire can be installed. To do this, you will need more ground clearance than is required to remove the flat tire.

WARNING:

Do not get under the car when it is supported by the jack! This is very dangerous as the vehicle could fall and cause serious injury or death. No one should stay in the car while the jack is being used.

nfhma-3.p65

1/13/2006, 2:41 PM

WHAT TO DO IN AN EMERGENCY

WARNING:

If there is, remove it. If there is not good contact on the mounting sur- face between the wheel and hub, the wheel nuts could come loose and cause the loss of a wheel. Loss of a wheel may result in loss of control of the vehicle. This may cause serious injury or death.

D060G02Y-AAT

6. Changing Wheels

D060G01NF-A Loosen the wheel nuts and remove them with your fingers. Slide the wheel off the studs and lay it flat so it cannot roll away. To put the wheel on the hub, pick up the spare tire, line up the holes with the studs and slide the wheel onto them. If this is difficult, tip the wheel slightly and get the top hole in the wheel lined up with the top stud. Then jiggle the wheel back and forth until the wheel can be slid over the other studs.

D060G02NF

! WARNING:

Wheels and wheel covers may have sharp edges. Handle them carefully to avoid possible severe injury. Be- fore putting the wheel into place, be sure that there is nothing on the hub or wheel (such as mud, tar, gravel, etc.) that interferes with the wheel from fitting solidly against the hub.

nfhma-3.p65

1/13/2006, 2:41 PM

WHAT TO DO IN AN EMERGENCY

10

D060H02O-AAT

7. Reinstall Wheel Nuts

D060I01E-AAT

8. Lower Vehicle and Tighten Nuts

D060H01NF-A To reinstall the wheel, hold it on the studs, put the wheel nuts on the studs and tighten them finger tight. The nuts should be installed with their small di- ameter ends directed inward. Jiggle the tire to be sure it is completely seated, then tighten the nuts as much as pos- sible with your fingers again.

D060I01NF Lower the car to the ground by turning the wheel nut wrench counterclock- wise.

HNF4013-A Then position the wrench as shown in the drawing and tighten the wheel nuts. Be sure the socket is seated com- pletely over the nut. Do not stand on the wrench handle or use an extension pipe over the wrench handle. Go around the wheel tightening every other nut until they are all tight. Then double-check each nut for tightness. After changing wheels, have a techni- cian tighten the wheel nuts to their proper torque as soon as possible.

nfhma-3.p65

10

1/13/2006, 2:41 PM

Wheel nut tightening torque: Steel wheel & aluminium alloy wheel: 65-80 lb.ft (900-1,100 kg.cm)

D060J02O-AAT

After Changing Wheels

it is correct. Always reinstall the valve cap after checking or adjusting tire pressure. If the cap is not replaced, air may leak from the tire. If you lose a valve cap, buy another and install it as soon as possible. After you have changed wheels, al- ways secure the flat tire in its place and return the jack and tools to their proper storage locations.

11

WHAT TO DO IN AN EMERGENCY

IF YOUR VEHICLE MUST BE TOWED D080A01O-GAT If your vehicle has to be towed, it should be done by your Hyundai dealer or a commercial tow truck service. This will help assure that your vehicle is not damaged in towing. Also, profes- sionals are generally aware of local laws gov- erning towing. In any case, rather than risk damage to your car, it is suggested that you show this information to the tow truck operator. Be sure that a safety chain system is used and that all local laws are observed. It is recommended that your vehicle be towed with a wheel lift and dollies or flatbed equipment with all the wheels off the ground.

CAUTION:

incorrectly!

o Your vehicle can be damaged if towed

o Be sure the transaxle is in neutral. o When the engine will not start, be sure the steering is unlocked by placing the key in the "ACC" position.

HNF5016-A

If you have a tire gauge, remove the valve cap and check the air pressure. If the pressure is lower than recom- mended, drive slowly to the nearest service station and inflate to the correct pressure. If it is too high, adjust it until

nfhma-3.p65

11

1/13/2006, 2:41 PM

WHAT TO DO IN AN EMERGENCY

12

D080B01O-GAT Towing the Vehicle

1)

2)

3)

dolly

HNF4015

Your vehicle can be towed by wheel lift type truck (1), (2) or flatbed equipment (3).

CAUTION:

o When towing the vehicle, take care not to cause damage to the bumper or under- body of the vehicle.

D080B01NF

o Do not tow with sling type truck as this may cause damage to the bumper or underbody of the vehicle.

1) If the vehicle is being towed with the rear wheels on the ground, be sure the parking brake is released.

NOTE: Before towing, check the level of the auto- matic transaxle fluid. If it is below the "HOT" range on the dipstick, add fluid. If you cannot add fluid, a towing dolly must be used.

2) If any of the loaded wheels or suspension components are damaged or the vehicle is being towed with the front wheels on the ground, use a towing dolly under the front wheels.

o Manual Transaxle:

If you do not use a towing dolly, place the ignition key in the "ACC" position and put the transaxle in "N (Neutral)".

CAUTION:

Do not tow with the key removed or in the "LOCK" position when towing from the rear without a towing dolly.

nfhma-3.p65

12

1/13/2006, 2:41 PM

EMERGENCY TOWING

o Automatic Transaxle:

Be sure to use a towing dolly under the front wheels.

D080D01NF-AAT

CAUTION:

WHAT TO DO IN AN EMERGENCY

13

NOTE: Before towing, check the level of the auto- matic transaxle fluid. If it is below the "HOT" range on the dipstick, add fluid. If you cannot add fluid, a towing dolly must be used.

CAUTION:

If the car is being towed with all four wheels on the ground, it can be towed only from the front. Be sure that the transaxle is in neutral. Do not tow at speeds greater than 30 mph (50 km/h) and for more than 15 miles (25
km). Be sure the steering is unlocked by placing the key in the "ACC" position. A driver must be in the towed vehicle to operate the steering and brakes.

D080D02NF-A For emergency towing when no commercial tow vehicle is available, attach a tow cable, chain or strap to the towing hook under the front of your car. Do not attempt to tow your vehicle in this manner on any unpaved surface. This could result in serious damage to your car. Nor should towing be attempted if the wheels, drive train, axles, steering or brakes are dam- aged. Before towing, be sure the transaxle is in neutral and the key is in "ACC" (with the engine off) or in the "ON" position (with the engine running). A driver must be in the towed car to steer it and operate the brakes.

D080B02NF

A vehicle with an automatic transaxle should never be towed from the rear with the front wheels on the ground. This can cause se- rious damage to the transaxle.

3) It is recommended that your vehicle be

towed with all the wheels off the ground.

nfhma-3.p65

13

1/13/2006, 2:41 PM

3
14

WHAT TO DO IN AN EMERGENCY

IF YOU LOSE YOUR KEYS

D120A01A-AAT If you lose your keys, many Hyundai dealers can make you a new key if you have your key number. If you lock the keys inside your car and you cannot obtain a new key, many Hyundai dealers can use special tools to open the door for you.

nfhma-3.p65

14

1/13/2006, 2:41 PM

CORROSION PREVENTION & APPEARANCE CARE

Corrosion Protection ..................................................... 4-2
To Help Prevent Corrosion ........................................... 4-2
Washing and Waxing .................................................... 4-3
Cleaning the Interior ...................................................... 4-5

nfhma-4.p65

3/9/2005, 10:45 AM

4 CORROSION PREVENTION AND APPEARANCE CARE

CORROSION PROTECTION

E010A01A-AAT Protecting Your Hyundai from Corro- sion

By using the most advanced design and con- struction practices to combat corrosion, Hyundai produces cars of the highest quality. However, this is only part of the job. To achieve the long-term corrosion resistance your Hyundai can deliver, the owner's cooperation and assistance is also required.

E010B01A-AAT Common Causes of Corrosion

The most common causes of corrosion on your car are:

o Road salt, dirt and moisture that is allowed to

accumulate underneath the car.

o Removal of paint or protective coatings by stones, gravel, abrasion or minor scrapes and dents which leave unprotected metal exposed to corrosion.

E010C01A-AAT High-Corrosion Areas

If you live in an area where your car is regularly exposed to corrosive materials, corrosion pro- tection is particularly important. Some of the common causes of accelerated corrosion are road salts, dust control chemicals, ocean air and industrial pollution.

E010D01A-AAT Moisture Breeds Corrosion

Moisture creates the conditions in which corro- sion is most likely to occur. For example, cor- rosion is accelerated by high humidity, particu- larly when temperatures are just above freez- ing. In such conditions, the corrosive material is kept in contact with the car surfaces by mois- ture that is slow to evaporate. Mud is particularly corrosive because it is slow to dry and holds moisture in contact with the vehicle. Although the mud appears to be dry, it can still retain the moisture and promote corro- sion. High temperatures can also accelerate corro- sion of parts that are not properly ventilated so the moisture can be dispersed. For all these reasons, it is particularly important to keep your car clean and free of mud or accumulations of other materials. This applies not only to the visible surfaces but particularly to the underside of the car.

TO HELP PREVENT CORROSION

E020A01A-AAT You can help prevent corrosion from getting started by observing the following:

E020B01A-AAT Keep Your Car Clean

The best way to prevent corrosion is to keep your car clean and free of corrosive materials. Attention to the underside of the car is particu- larly important.

o If you live in a high-corrosion area — where road salts are used, near the ocean, areas with industrial pollution, acid rain, etc.—, you should take extra care to prevent corrosion. In winter, hose off the underside of your car at least once a month and be sure to clean the underside thoroughly when winter is over.

o When cleaning underneath the car, give particular attention to the components under the fenders and other areas that are hidden from view. Do a thorough job; just dampening the accumulated mud rather than washing it away will accelerate corrosion rather than prevent it. Water under high pressure and steam are particularly effective in removing accumulated mud and corrosive materials.

nfhma-4.p65

3/9/2005, 10:45 AM

o When cleaning lower door panels, rocker panels and frame members, be sure that drain holes are kept open so that moisture can escape and not be trapped inside to ac- celerate corrosion.

E020C01A-AAT Keep Your Garage Dry

Don't park your car in a damp, poorly ventilated garage. This creates a favorable environment for corrosion. This is particularly true if you wash your car in the garage or drive it into the garage when it is still wet or covered with snow, ice or mud. Even a heated garage can contrib- ute to corrosion unless it is well ventilated so moisture is dispersed.

E020D02A-AAT Keep Paint and Trim in Good Condition

Scratches or chips in the finish should be covered with "touch-up" paint as soon as pos- sible to reduce the possibility of corrosion. If bare metal is showing through, the attention of a qualified body and paint shop is recommended.

Bird droppings : Bird droppings are highly cor- rosive and may damage painted surfaces in just a few hours. Always remove bird droppings as soon as possible.

E020E01A-AAT Don't Neglect the Interior

Moisture can collect under the floor mats and carpeting to cause corrosion. Check under the mats periodically to be sure the carpeting is dry. Use particular care if you carry fertilizers, clean- ing materials or chemicals in the car. These should be carried only in proper contain- ers and any spills or leaks should be cleaned up, flushed with clean water and thoroughly dried.

CORROSION PREVENTION AND APPEARANCE CARE

WASHING AND WAXING

E030A01A-AAT Washing Your Hyundai

Never wash your car when the surface is hot from being in the sun. Always wash your car in the shade.

Wash your car frequently. Dirt is abrasive and can scratch the paint if it is not removed. Air pollution or acid rain may damage the paint and trim through chemical action if pollutants are allowed to remain in contact with the surface. If you live near the ocean or in an area where road salts or dust control chemicals are used, you should pay particular attention to the underside of the car. Start by rinsing the car to remove dust and loose dirt. In winter, or if you have driven through mud or muddy water, be sure to thor- oughly clean the underside as well. Use a hard direct stream of water to remove accumulations of mud or corrosive materials. Use a good quality car-washing solution and follow the manufacturer's directions on the package. These are available at your Hyundai dealer or auto parts outlet. Don't use strong household detergents, gasoline, strong solvents or abra- sive cleaning powders as these may damage the finish. Use a clean sponge or cloth, rinse it frequently and don't damage the finish by rubbing too hard. For stubborn spots, dampen them frequently and remove them a little at a time.

nfhma-4.p65

3/9/2005, 10:45 AM

4 CORROSION PREVENTION AND APPEARANCE CARE

To clean whitewall tires, use a stiff brush or soapy steel-wool scouring pad.