2006 Hyundai Santa FE Owners Manual

G120D01A-AAT To Check the Fluid Level

HSM5011

The fluid level in the brake fluid reservoir should be checked periodically. The level should be between the "MIN" and "MAX" marks on the side of the reservoir. If the level is at or below the "MIN" mark, carefully add fluid to bring it up to "MAX". Do not overfill.

Fluid level should be within "HOT" range

3.

HJM5044
If the transaxle fluid level is low, use a funnel to add transaxle fluid through the dipstick tube until the level reaches the "HOT" range. Do not overfill.

WARNING:

The cooling fan is controlled by engine coolant temperature and may sometimes operate even when the engine is not run- ning. Use extreme caution when working near the blades of the cooling fan, so that you are not injured by a rotating fan blade. As the engine coolant temperature de- creases, the fan will automatically shut off. This is a normal condition.

6 DO-IT-YOURSELF MAINTENANCE 16

AIR CONDITIONING CARE

G120E02A-AAT Adding Brake Fluid

G140A01A-AAT Keeping the Condenser Clean

G140C01A-AAT Lubrication

WARNING:

Handle brake fluid carefully. It can damage your vision if it gets into your eyes. Use only DOT 3 or DOT 4 specification fluid from a sealed container. Do not allow the fluid can or reservoir to remain open any longer than required. This will prevent entry of dirt and moisture which can damage the brake sys- tem and cause improper operation.

To add brake fluid, first wipe away any dirt, then unscrew the fluid reservoir cap. Slowly pour the recommended fluid into the reservoir. Do not overfill. Carefully replace the cap on the reser- voir and tighten.

The air conditioning condenser (and engine radiator) should be checked periodically for accumulation of dirt, dead insects, leaves, etc. These can interfere with maximum cooling ef- ficiency. When removing such accumulations, brush or hose them away carefully to avoid bending the cooling fans.

To lubricate the compressor and the seals in the system, the air conditioning should be run for at least 10 minutes each week. This is particularly important during cool weather when the air conditioning system is not otherwise in use.

G140B01A-AAT Checking the Air Conditioning Opera- tion

1. Start the engine and let it run at a fast idle for several minutes with the air conditioning set at the maximum cold setting. If the air coming out of the in-dash vents is not cold, have the air conditioning system inspected by your Hyundai dealer.

2.

CAUTION:

Running the air conditioning system for extended periods of time with a low refrig- erant level may damage the compressor.

G140D02A-AAT Checking the Compressor Drive Belt

2.7 V6

Auto tensioner

Power steering pulley

A/C comp.

Generator

Crankshaft pulley

G190A02B

3.5 V6

Power steering pulley

Generator

Crankshaft pulley

A/C pulley

G140D02L

When the air conditioning is being used regu- larly, the compressor drive belt tension should be checked at least once a month with the engine turned off. To check the drive belt tension, press down on the belt halfway between the engine crankshaft and compressor pulleys. Pressing with your finger, you should not be able to deflect this belt anymore than 1/3 of an inch. If the belt is too loose, have it adjusted by your Hyundai dealer.

CHANGING THE CLIMATE CON- TROL AIR FILTER

B145A03O-GAT (For Evaporator and Blower Unit) (If Installed)

The climate control air filter is located in front of the evaporator unit behind the glove box. It helps to decrease the amount of pollutants entering the car.

1. Open the glove box and take out the damper

strap through the hole.

HSM412

DO-IT-YOURSELF MAINTENANCE

17

2. Lower the glove box down completely by pushing the both sides of the glove box inward.

HSM345

HSM442
3. Turn over the wall paper on the climate

control air filter cover.

6 DO-IT-YOURSELF MAINTENANCE 18

HSM444

HSM443

4. Turn the knob of the climate control air filter cover counterclockwise and remove the climate control air filter cover.

5. Replace two climate control air filters by pulling the knob of the air conditioner filter outward. Installation is the reverse order of disassem- bly.

6.

CAUTION:

Be sure to install the climate control air filter in the direction of the arrow sign. Other- wise, it may cause noise or deterioration.

CHECKING THE FREE-PLAY

G150A01A-AAT STEERING WHEEL

1.18 in. (30 mm)

G150A01O

To check the steering wheel free-play, stop the car with the wheels pointed straight ahead and gently move the steering wheel back and forth. Use very light finger pressure and be sensitive to changes in resistance that mark the limits of the free-play. If the free-play is greater than specified, have it inspected by your Hyundai dealer and adjusted or repaired if necessary.

G170A01A-AAT BRAKE PEDAL

CHECKING BRAKE PEDAL CLEARANCE

G180A01A-AAT

0.12 ~ 0.31 in. (3 ~ 8 mm)

2.95 in. (75 mm)

G160A01HR With the engine off, press down on the brake pedal several times to reduce the vacuum in the brake booster. Then, using your hand, press down slowly on the brake pedal until you feel a change in resistance. This is the brake pedal free-play. The free-play should be within the limits speci- fied in the illustration above. If it is not, have it inspected by your Hyundai dealer and adjusted or repaired if necessary.

G180A01L You need a helper to check the brake pedal clearance. With the engine running, have your helper press down on the brake pedal several times and then hold it down with a force of about 110 lbs (50 kg, 490 N). The brake pedal clear- ance is the distance from the top surface of the brake pedal to the asphalt sheeting under the floor mat. If the brake pedal clearance is not within the limits specified in the illustration, have it in- spected by your Hyundai dealer and adjusted or repaired if necessary.

DO-IT-YOURSELF MAINTENANCE

CHECKING DRIVE BELTS

19

G190A01A-AAT 2.7 V6

Auto tensioner

Power steering pulley

A/C comp.

Generator

Crankshaft pulley

G190A02B

3.5 V6

Power steering pulley

Generator

Crankshaft pulley

A/C pulley

G140D02L

6 DO-IT-YOURSELF MAINTENANCE 20

Drive belts should be checked periodically for proper tension and adjusted if necessary. At the same time, belts should be examined for cracks, wear, fraying or other evidence of deterioration and replaced if necessary. Belt routing should also be checked to be sure there is no interference between the belts and other parts of the engine. After a belt is replaced, the new belt should be adjusted again after two or three weeks to eliminate slack resulting from initial stretching after use.

CAUTION:

When replacing a fusible link, never use anything but a new fusible link with the same or lower amperage rating. Never use a piece of wire or a higher-rated fusible link. This could result in serious damage and create a fire hazard.

CHECKING AND REPLACING FUSES G200A03A-AAT Replacing a Fusible Link

Open- Replace

Good

G200A01O A fusible link will melt if the electrical circuits from the battery are ever overloaded, thus prevent- ing damage to the entire wiring harness. (This could be caused by a short in the system drawing too much current.) If this ever happens, have a Hyundai dealer determine the cause, repair the system and replace the fusible link. The fusible links are located in a relay box in the engine compartment for easy inspection.

1. Turn off the ignition and all other switches. 2. Open the fuse box and examine each fuse. Remove each fuse by pulling it toward you (a small "fuse puller" tool is contained in the relay and fuse box of the engine room to simplify this operation).

3. Be sure to check all other fuses, even if you

find one that appears to have opened.

DO-IT-YOURSELF MAINTENANCE

21

4. Replace the blown fuse by pressing a new fuse of the same rating into place. The fuse should be a snug fit. If it is not, have the fuse clip repaired or replaced by a Hyundai dealer. If you do not have a spare fuse, you may be able to borrow a fuse of the same or lower rating from an accessory you can tempo- rarily get along without (the radio or cigarette lighter, for example). Always remember to replace the borrowed fuse.

G200A02O

Good

Open-Replace

G200B02L

G200B02HP-AAT Replacing Accessory Fuses

HSM4002
The fuse box for the lights and other electrical accessories will be found low on the dashboard on the driver's side. Inside the box you will find a list showing the circuits protected by each fuse. If any of your car's lights or other electrical accessories stop working, a blown (open) fuse could be the reason. If the fuse has opened, you will see that the metal strip inside the fuse has melted through. If you suspect a blown fuse, follow this procedure:

6 DO-IT-YOURSELF MAINTENANCE 22

CHECKING THE BATTERY

G210A01A-AAT

CAUTION:

An open fuse indicates that there is a prob- lem in the electrical circuit. If you replace a fuse and it blows as soon as the accessory is turned on, the problem is serious and should be referred to a Hyundai dealer for diagnosis and repair. Never replace a fuse with anything except a fuse with the same or a lower amperage rating. A higher capac- ity fuse could cause damage and create a fire hazard.

NOTE: See page 6-33 for the fuse panel descrip- tions.

D010B01O

WARNING:

Batteries can be dangerous! When working with batteries, carefully observe the follow- ing precautions to avoid serious injuries.

The fluid in the battery contains a strong solution of sulfuric acid, which is poisonous and highly corrosive. Be careful not to spill it on yourself or the car. If you do spill battery fluid on yourself, immediately do the following:

o If battery fluid is on your skin, flush the affected areas with water for at least 15
minutes and then seek medical assistance. o If battery fluid is in your eyes, rinse out your eyes with water and get medical assistance as soon as possible. While you are being driven to get medical assistance, continue to rinse your eyes by using a sponge or soft cloth saturated with water.

o If you swallow battery fluid, drink a large quantity of water or milk followed by milk of magnesia, eat a raw egg or drink vegetable oil. Get medical assistance as soon as possible.

While batteries are being charged (either by a battery charger or by the vehicle's generator), they produce explosive gases. Always ob- serve these warnings to prevent injuries from occurring:

o Charge batteries only in a well ventilated

o Do not permit flames, sparks or smoking in

area.

the area.

o Keep children away from the area.

G210B03A-AAT Checking the Battery

Keep the battery clean. Any evidence of corro- sion around the battery posts or terminals should be removed using a solution of house- hold baking soda and warm water. After the battery terminals are dry, cover them with a light coating of grease.

PROPOSITION 65 WARNING: Battery posts, terminals, and related acces- sories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Batteries also contain other chemicals known to the State of California to cause cancer. Wash hands after handling.

CHECKING ELECTRIC COOLING FANS G220A01A-AAT

DO-IT-YOURSELF MAINTENANCE

POWER STEERING FLUID LEVEL

23

G230A03A-AAT

WARNING:

The cooling fan is controlled by engine coolant temperature and may sometimes operate even when the engine is not run- ning. Use extreme caution when working near the blades of the cooling fan, so that you are not injured by a rotating fan blade. As the engine coolant temperature de- creases the fan will automatically shut off. This is a normal condition.

G220B01A-AAT Checking Engine Cooling Fan

The engine cooling fan should come on auto- matically if the engine coolant temperature is high.

G220C01A-AAT Checking Condenser Cooling Fan

The condenser cooling fan should come on automatically whenever the air conditioning is in operation.

HSM5010
The power steering fluid level should be checked regularly. To check the power steering fluid level, be sure the engine is "OFF", then check to make certain that the power steering fluid level is between the "MAX" and "MIN" level markings on the fluid reservoir.

NOTE: Grinding noise from the power steering pump may be heard immediately after the engine is started in extremely cold condi- tions (below - 4°F). If the noise stops during warm up, there is no abnormal function in the system. It is due to a power steering fluid characteristic in extremely cold condi- tions.

6 DO-IT-YOURSELF MAINTENANCE 24

Recommended Fluid Use PSF-3 type fluid

NOTE: Do not start the engine when the power steering oil reservoir is empty.

G240A01A-AAT POWER STEERING HOSES

It is suggested that you check the power steer- ing hose connections for fluid leakage at those intervals specified in the vehicle maintenance schedule in Section 5. The power steering hoses should be replaced if there is severe surface cracking, pulling, scuffing or worn spots. Deterioration of the hose could cause premature failure.

G250A01A-AAT FOR MORE INFORMATION ABOUT YOUR HYUNDAI

If you desire additional information about main- taining and servicing your Hyundai, you may purchase a factory Shop Manual at your Hyundai dealer's parts department. This is the same manual used by dealership technicians and while it is highly technical it can be useful in obtaining a better understanding of your car and how it works.

HEADLIGHT AIMING ADJUSTMENT

G290A02O-AAT Before performing aiming adjustment, make sure of the following. 1. Keep all tires inflated to the correct pressure. 2. Place the vehicle on level ground and press the front bumper & rear bumper down sev- eral times. Place vehicle at a distance of 118 in. (3m) from the test wall.

3. See that the vehicle is unloaded (except for full levels of coolant, engine oil and fuel, and spare tire, jack, and tools). Have the driver or equivalent weight placed in driver's seat. 4. Clean the head light lenses and turn on the

headlights (Low beam).

5. Open the hood.

Vertical aiming

G290A01O

6. Draw a vertical line (through the center of each headlight beam pattern) and a horizon- tal line (through the center of each headlight beam pattern) on the aiming screen. And then, draw a parallel line at 0.8 in. (21
mm) under the horizontal line.

7. Adjust each cut-off line of the low beam to the parallel line with a phillips screwdriver - VERTICAL AIMING.

WARNING:

Horizontal aiming should be adjusted by an authorized Hyundai dealer.

DO-IT-YOURSELF MAINTENANCE

25

G290B01O-AAT Adjustment After Headlight Assembly Replacement

Vertical line

Horizontal line

Cut-off line

"P"

Ground line

SPECIFICATION:

"H"; Horizontal center line of headlights from ground: 2WD : 32.5 in.(822 mm) 4WD : 33.3 in.(843 mm)

"W"; Distance between each headlight center: 46.5 in.(1,178 mm)

"L"; Distance between the headlights and the wall that the lights are tested against: 118 in. (3,000 mm).

G290A03O If the vehicle has had front body repair and the headlight assembly has been replaced, the headlight aiming should be checked using an aiming chart as shown in the illustration. Turn on the headlight switch. (Low Beam Position)

1. Adjust headlights so that main axis of light is parallel to center line of the body and is aligned with point "P" shown in the illustration. 2. Dotted lines in the illustration show the center

of headlights.

6 DO-IT-YOURSELF MAINTENANCE 26

REPLACEMENT OF LIGHT BULBS

G260A03A-AAT Before attempting to replace a light bulb, be sure the switch is turned to the "OFF" position. The next paragraph shows how to reach the light bulbs so they may be changed. Be sure to replace the burned-out bulb with one of the same number and wattage rating.

See page 6-32 for the wattage description.

NOTE: After heavy, driving rain or washing, head- light and taillight lenses could appear frosty. This condition is caused by the tempera- ture difference between the lamp inside and outside. This is similar to the conden- sation on your windows inside your vehicle during the rain and doesn’t indicate a prob- lem with your vehicle. If the water leaks into the lamp bulb circuitry, have the vehicle checked by an Authorized Hyundai Dealer.

CAUTION:

Keep the lamps out of contact with petro- leum products, such as oil, gasoline, etc.

G270A02O-AAT Headlight and Front Turn Signal Light

1. Allow the bulb to cool. Wear eye protection. 2. Open the engine hood. 3. Always grasp the bulb by its plastic base,

avoid touching the glass.

4. Using a socket wrench of the correct size, remove the headlight assembly mounting bolts.

HSM353

HSM328
5. Disconnect the power cord from the bulb

base in the back of the headlight.

G270A01O

6. Turn the plastic cover counterclockwise

and remove it.

DO-IT-YOURSELF MAINTENANCE

27

HSM329
7. Disconnect the connector from the bulb

base in the back of the headlight.

HSM330
8. Push the bulb spring to remove the headlight

bulb.

HSM331
9. Remove the protective cap from the re- placement bulb and install the new bulb by matching the plastic base with the headlight hole. Reattach the bulb spring and recon- nect the connector.

10.Use the protective cap and carton to prompt-

ly dispose of the old bulb.

11.Check for proper headlight aim.

6 DO-IT-YOURSELF MAINTENANCE 28

HSM332
12.To replace the front turn signal light bulb, remove from the bulb holder and install the new bulb. Do not touch the glass of the new bulb.

G270B02O-GAT Rear Combination Light

(1)

G270A03O

(2)

(3)

WARNING:

This halogen bulb contains gas under pres- sure and if impacted could shatter, result- ing in flying fragments. Always wear eye protection when servicing the bulb. Protect the bulb against abrasions or scratches and against liquids when lighted. Turn the bulb on only when installing in a headlight. Replace the headlight if damaged or cracked. Keep the bulb out of the reach of children and dispose of the used bulb with care.

G270B01O

G270B02O

1. Open the tail gate. 2. Remove the mounting screws of the rear combination light as shown with a phillips screwdriver.

G270C01O-AAT Luggage Compartment Light

DO-IT-YOURSELF MAINTENANCE

29

(2)

(1)

(3)

G270B03O

3. To replace the rear combination light, take it out from the bulb holder by turning it coun- terclockwise.

(1) Stop/Tail light (2) Back-up light (3) Turn signal light

4.

Install the new bulb.

HSM341

3. Replace with a new bulb.

HSM342

1. Open the tail gate. 2. Remove the cover with a flat-head screw-

driver.

6 DO-IT-YOURSELF MAINTENANCE 30

G270E01O-AAT Front Side Marker Light

G270G01O-AAT Interior Light

HSM334
1. Remove the cover with a phillips screw-

driver.

2. Disconnect the connector.

HSM335

HSM343
1. Remove the cover with a flat-head screw-

driver.

3. Replace with a new bulb.

HSM336

G270H01O-AAT Glove Box Illuminated Light

DO-IT-YOURSELF MAINTENANCE

31

2. Replace with a new bulb.

HSM344

HSM366

3. Disconnect the connector.

G270E02L

1. Open the glove box. 2. Remove the cover with a flat-head screw-

driver.

4. Replace with a new bulb.

HTB284

6 DO-IT-YOURSELF MAINTENANCE 32

BULB WATTAGE

G280A03O-AAT

No.

Part Name

Wattage

Socket type

Glove Box Illuminated Light Headlight (Low/High) Turn Signal Light/Front Position Light

Map Light

With sunroof Without sunroof

Interior Light Front Fog Light (If installed) Side Marker Light

55/60
28/8
10
10
27

S8.5/8.5

P43t BA15d BA9s BA9s

S8.5/8.5
PG13

W2.1×9.5D

12

No. 10
11

Part Name

Wattage

Front Door Edge Warning Light (If installed) Luggage Compartment Light High Mounted Rear Stop Light (If installed) Rear Combination Light Turn Signal Light Stop/Tail Light (Side Marker Light) Back-up Light License Plate Light

10
17

27

27/8(8)

27

G280A01O-A

Socket type W2.1×4.6D

S8.5/8.5

W-2

BA15s BA15d BA15s

W2.1×9.5D

FUSE PANEL DESCRIPTION

G200C02O-AAT Engine Compartment

DO-IT-YOURSELF MAINTENANCE

33

DESCRIPTION

FUSE

RATING

PROTECTED COMPONENTS

FUSIBLE

LINK

FUSE

ALT B+ IGN BLR ABS.1
ABS.2
ECU P/W

RAD FAN

C/FAN

FRT FOG H/LP(LH) H/LP(RH) ECU #1
ECU #2
ECU #3
ECU(B+)

ATM HORN

A/C

ST SIG

140A 50A 50A 40A 30A 30A 40A 30A 40A 20A 15A 10A 10A 20A 20A 10A 15A 20A 10A 10A 10A

Generator Tail lamp relay, Fuse 11~17, Power connector Start relay, Ignition switch A/C Fuse, Blower relay ABS control module, Air bleeding connector ABS control module, Air bleeding connector Engine contorl relay Power window relay, Fuse 26
Radiator fan relay Condenser fan relay Fog lamp relay Left head lamp, Instrument cluster, DRL control module Right head lamp Ignition failure sensor, Oxygen sensor Injector Check engine ind, ECM, PCM Fuel pump relay, ECM, TCM, Generator, PCM ATM contorl relay, 4WD control module Horn relay A/C relay PCM, ECM

NOTE: Not all fuse panel descriptions in this manual may be applicable to your vehicle. It is accurate at the time of printing. When you inspect the fuse box on your vehicle, refer to the fuse box label.

G200C01O

6 DO-IT-YOURSELF MAINTENANCE 34

G200E01O-AAT Inner Panel

FUSE

FUSE RATING

PROTECTED COMPONENTS

F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
F13
F14
F15
F16
F17
F18

F19

F20
F21
F22
F23
F24
F25
F26
F27
F28
F29
F30
F31

20A 10A 15A 10A 10A 25A 10A 10A 10A 10A 10A 15A 20A 10A 10A 25A 20A 30A

10A

15A 10A 10A 10A 10A 10A 20A 10A 10A 15A 10A 20A

Cigarette lighter & Power outlet Audio, Power outside mirror Digital clock, Rear power outlet Cruise control Head lamp relay Seat warmer Rear wiper motor control Rear window defogger, Power outside mirror A/C control, Sunroof controller, Electrical chrome mirror (Not used) Room lamp, Door warning switch, Door lamp, Manual A/C control, Homelink controller Digatal clock, ETACM, Audio, Siren AMP speakers Stop lamp, Data link connector, Multipurpose check connector Hazard lamp Power seat, Rear wiper motor control Sunroof controller Defogger relay Instrument cluster, Pre-excitation resistor, ETACM, Auto light sensor, DRL control module, Generator SRS control module ECM (V6 2.7L) Instrument cluster (Airbag IND) ABS control module, G-Sensor, Air bledding connector, 4WD control module Turn signal lamp Back-up lamps, TCM, Vehicle speed secsor, ETS control module, Ignition failure sensor Door lock/unlock relay, Key lock/unlock relay Tail & parking lamp (LH), Turn signal lamp, License lamp Tail & parking lamp (RH), Fog lamp relay, Switch illumination ETS control module (V6 3.5L), Fail safety relay Radiator fan relay, Condenser fan relay Front wiper motor, Wiper relay, Washer motor

G200E01O-A

EMISSION CONTROL SYSTEMS

Emission Control System ............................................. 7-2
EGR System ................................................................. 7-3
Catalytic Converter ....................................................... 7-3

smhma-7.p65

3/9/2005, 4:27 PM

7 EMISSION CONTROL SYSTEMS

EMISSION CONTROL SYSTEM

H010A03O-AAT Your Hyundai is equipped with an emission control system to meet all requirements of the U.S. Environmental Protection Agency or Cali- fornia Air Resources Board. There are three emission control systems which are as follows.

o 3.5 V6 - To prevent the vehicle from misfiring during dynamometer testing, turn the Traction Control System (TCS) off by pressing the TCS switch. After dynamometer testing is completed, turn the TCS system back on by pressing the TCS switch again.

(1) Crankcase emission control system (2) Evaporative emission control system (3) Exhaust emission control system

In order to assure the proper function of the emission control systems, it is recommended that you have your car inspected and main- tained by an authorized Hyundai dealer in ac- cordance with the maintenance schedule in this manual.

Caution for the Inspection and Maintenance Test (V6 Vehicle with Traction Control Sys- tem)

o 2.7 V6 - To prevent the vehicle from misfiring during dynamometer testing, disconnect the ABS connector in the engine compartment. After dynamom- eter testing is completed, erase the ABS/ TCS DTC (Diagnotic Trouble Code) with a GST (Generic Scan Tool) or Hi-Scan Pro. For more information, see shop manual (Wheel Speed Sensor).

H010B01A-AAT 1. Crankcase Emission Control

System

The positive crankcase ventilation system is employed to prevent air pollution caused by blow-by gases being emitted from the crank- case. This system supplies filtered air to the crankcase through the air intake hose. Inside the crankcase, the fresh air mixes with blow-by gases, which then pass through the PCV valve and into the induction system.

H010C01S-AAT 2. Evaporative Emission Control (Includ- ing ORVR: Onboard Refueling Vapor Recovery) System

The Evaporative Emission Control System is designed to prevent fuel vapors from escaping into the atmosphere.

(The ORVR system is designed to allow the vapors from the fuel tank to be loaded into a canister while refueling at the gas station, pre- venting the escape of fuel vapors into the atmosphere.)

Canister

Fuel vapors generated inside the fuel tank are absorbed and stored in the canister. When the engine is running, the fuel vapors absorbed in the canister are drawn into the induction system through the purge control solenoid valve.

Purge Control Solenoid Valve (PCSV)

The purge control solenoid valve is controlled by the Engine Control Module (ECM); when the engine coolant temperature is low during idling, the PCSV closes so that evaporated fuel is not taken into the engine. After the engine warms- up during ordinary driving, the PCSV opens to introduce evaporated fuel to the engine.

H010D01A-AAT 3. Exhaust Emission Control System

The Exhaust Emission Control System is a highly effective system which controls exhaust emissions while maintaining good vehicle performace.

smhma-7.p65

3/9/2005, 4:27 PM

EGR SYSTEM

CATALYTIC CONVERTER

H010E01Y-AAT (If installed)

H020A01A-AAT

This system helps reduce nitrogen oxides by recirculating a part of the exhaust gas into the engine, thereby reducing cylinder combustion temperature, which results in lower output of oxides of nitrogen.

Catalytic Converter

H020A01O All Hyundai vehicles are equipped with a mono- lith type three-way catalytic converter to re- duce the carbon monoxide, hydrocarbons and nitrogen oxides contained in the exhaust gas. Exhaust gases passing through the catalytic converter cause it to operate at a very high temperature. The introduction of large amounts of unburned gasoline into the exhaust may cause the catalytic converter to overheat and create a fire hazard. This risk may be reduced by observing the following:

EMISSION CONTROL SYSTEMS

WARNING:

o Use unleaded fuel only. o Maintain the engine in good operating condition. Extremely high catalytic con- verter temperatures can result from im- proper operation of the electrical, igni- tion or multiport electronic fuel injec- tion.

o If your engine stalls, pings, knocks, or is hard to start, have your Hyundai dealer inspect and repair the problem as soon as possible.

o Avoid driving with a very low fuel level. Running out of gasoline may cause the engine to misfire and result in damage to the catalytic converter.

o Avoid idling the engine for periods

longer than 10 minutes.

o The vehicle should not be pushed or pulled to get started. This may cause the catalytic converter to overheat and cre- ate a fire hazard.

o Do not touch the catalytic converter or any other part of the exhaust system while the catalytic converter is hot. Shut off the engine, wait for at least one hour before touching the catalytic converter or any other part of the exhaust system. o Remember that your Hyundai dealer is

your best source of assistance.

smhma-7.p65

3/9/2005, 4:27 PM

7 EMISSION CONTROL SYSTEMS

WARNING:

o Do not stop your Hyundai over any com- bustible material such as grass, paper, leaves or rags. These materials might contact the hot catalytic converter and a fire might result.

smhma-7.p65

3/9/2005, 4:27 PM

CONSUMER INFORMATION, REPORTING

SAFETY DEFECTS & BINDING

ARBITRATION OF WARRANTY CLAIMS

Vehicle Identification Number (VIN) .............................. 8-2
Engine Number ............................................................. 8-2
Tire Information ............................................................. 8-2
Recommended Cold Tire Inflation Pressures ............... 8-3
Tire Sidewall Labeling ................................................... 8-5
Tire Terminology and Definitions ................................... 8-7
Snow Tires .................................................................... 8-9
Tire Chains.................................................................. 8-10
Tire Rotation................................................................ 8-10
Tire Balancing ............................................................. 8-11
Tire Traction ................................................................ 8-11
When to Replace Tires ............................................... 8-11
Tire Maintenance ........................................................ 8-12
Spare Tire and Tools................................................... 8-13
Warranties for Your Hyundai Vehicle .......................... 8-13
Consumer Information ................................................. 8-14
Reporting Safety Defects ............................................ 8-16
Binding Arbitration of Warranty Claims ....................... 8-17

8 CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS

ENGINE NUMBER

VEHICLE IDENTIFICATION NUMBER (VIN)

I010A01O-AAT

I010B01A-AAT

2.7 V6

I010A01O The vehicle identification number (VIN) is the number used in registering your car and in all legal matters pertaining to its ownership, etc. It can be found in three different places on your car:

3.5 V6

I010B01B

TIRES

I020A02A-AAT TIRE INFORMATION The tires supplied on your new Hyundai are chosen to provide the best perfor- mance for normal driving. If you ever have questions about your tire warranty and where to obtain ser- vice, see the tire manufacture's booklet included with your vehicle's Owner's Manual Literature Kit.

1. On the bulkhead between the engine and

passenger compartments.

2. On the left top side of the instrument panel where it can be seen by looking down through the windshield.

3. On the lower side of the center pillar outer

panel.

The engine number is stamped on the engine block as shown in the drawing.

I010B01L

CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS

I030A02JM-AAT

RECOMMENDED COLD TIRE INFLA- TION PRESSURES

Type A

I030A01O Tire label located on the driver's side of the center pillar outer panel gives the cold tire pressures recommended for your vehicle with the original tire size, the number of people that can be in your vehicle and vehicle capacity weight.

Type B

I030A02O-A

I030A03O-A

These pressures were chosen to pro- vide the most satisfactory combination of ride comfort, tire wear and stability under normal conditions. Tire pressures should be checked at least monthly. Proper tire inflation pressures should be maintained for these reasons:

WARNING:

Severe underinflation (10 psi (70 kPa) or more) can lead to severe heat buildup, causing blowouts, tread separation and other tire failures that can result in the loss of vehicle con- trol leading to severe injury or death. This risk is much higher on hot days and when driving for protracted peri- ods at high speeds.

8 CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS

NOTE: o Underinflation also results in ex- cessive wear, poor handling and reduced fuel economy. Wheel de- formation also is possible. Keep your tire pressures at the proper levels. If a tire frequently needs refilling, have it checked by your Hyundai Dealer.

o Overinflation produces a harsh ride, excessive wear at the center of the tire tread, and a greater possibility of damage from road hazards.

WARNING:

Overinflation or underinflation can reduce the tire life, adversely affect vehicle handling, and lead to sud- den tire failure. This could rusult in loss of vehicle control and potential injury.

CAUTION:

Always observe the following:

o Check pressures when the tires are cold. (After the vehicle has been parked for at least three hours or hasn't been driven more than 1
mile (1.6 km) since starting up.)

o Check the pressure of your spare tire each time you check the pres- sure of other tires.

o Never overload your vehicle. Be especially careful about overload- ing if you equip your vehicle with a luggage rack.

o Worn, old tires can cause acci- dents. If your tread is badly worn, or if your tires have been dam- aged, replace them.

CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS

label, no further adjustment is neces- sary. If the pressure is low, add air until you reach the recommended amount. If you overfill the tire, release air by pushing on the metal stem in the center of the tire valve. Recheck the tire pres- sure with the tire gauge. Be sure to put the valve caps back on the valve stems. They help prevent leaks by keeping out dirt and moisture.

I030B01O-AAT TIRE SIDEWALL LABELING

5, 6

I030B04JM

Federal law requires tire manufacturers to place standardized information on the sidewall of all tires. This information identifies and describes the fundamen- tal characteristics of the tire and also provides the tire identification number (TIN) for safety standard certification. The TIN can be used to identify the tire in case of a recall.

I035A01JM-AAT

CHECKING TIRE INFLATION PRES- SURE Check your tires once a month or more. Also, check the tire pressure of the spare tire.

How to Check Use a good quality gauge to check tire pressure. You cannot tell if your tires are properly inflated simply by looking at them. Radial tires may look properly inflated even when they're underinflated. Check the tire's inflation pressure when the tires are cold. - "Cold" means your vehicle has been sitting for at least three hours or driven no more than 1
mile (1.6 km). Remove the valve cap from the tire valve stem. Press the tire gauge firmly onto the valve to get a pressure mea- surement. If the cold tire inflation pres- sure matches the recommended pres- sure on the tire and loading information

8 CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS

1. Manufacturer or Brand name

o Manufacturer or Brand name is

shown. 2. Tire size

(example: P225/70R16 101T) o The "P" indicates the tire is de-

signed for passenger vehicles.

o Three-digit number (225): This num- ber gives the width in millimeters of the tire from sidewall edge to sidewall edge.

o Two-digit number (70): This num- ber, known as the aspect ratio, gives the tire's ratio of height to width.

o R: The "R" stands for radial. o Two-digit number (16): This num- ber is the wheel or rim diameter in inches.

o Three digit number (101): This num- ber is the tire's load index. It is a measurement of how much weight each tire can support.

o T: Speed Rating. The speed rating denotes the speed at which a tire is designed to be driven for extended periods of time. The ratings range from "A" to "Z" (98 to 186 MPH). 3. TIN (Tire Identification Number) for new tire (example: DOT XX XX XXX XXXX) o DOT: Abbreviation for the "Depart- ment of Transportation". The sym- bol can be placed above, below or to the left or right of the Tire Iden tification Number. It indicates the tire is in compliance with the U.S. Department of Transportation Mo- tor Vehicle Safety Standards.

o 1st two-digit code: Manufacturer's

identification mark

o 2nd two-digit code: Tire size o 3rd three-digit code: Tire type code

(Optional)

o 4th four-digit code: Date of Manu-

facture

o Four numbers represent the week and year the tire was built. For example, the numbers 3105 means the 31st week of 2005.

4. Tire ply composition and material The number of layers or plies of rubbercoated fabric in the tire. Tire manufacturers also must indicate the materials in the tire, which in- clude steel, nylon, polyester, and others. The letter "R" means radial ply construction; the letter "D" means diagonal or bias ply construction; and the letter "B" means belted-bias ply construction.

5. Maximum permissible inflation

pressure This number is the greatest amount of air pressure that should be put in the tire. Do not exceed the maximum permissible inflation pressure. Refer to the Tire and Loading Information label for recommended inflation pres- sure.

6. Maximum load rating

This number indicates the maximum load in kilograms and pounds that can be carried by the tire. When replacing the tires on the vehicle, always use a tire that has the same load rating as the factory installed tire.

7. Uniform Tire Quality Grading

(UTQG): Tire manufacturers are required to grade tires based on three perfor- mance factors: treadwear, traction and temperature resistance. For more information, see Uniform Tire Qual- ity Grading on page 8-14.

CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS

I030D01JM-AAT

TIRE TERMINOLOGY AND DEFINI- TIONS Air Pressure: The amount of air inside the tire pressing outward on the tire. Air pressure is expressed in pounds per square inch (psi) or kilopascal (kPa). Accessory Weight: This means the combined weight of optional accesso- ries. Some examples of optional ac- cessories are, automatic transmission, power seats, and air conditioning. Aspect Ratio: The relationship of a tire's height to its width. Belt: A rubber coated layer of cords that is located between the plies and the tread. Cords may be made from steel or other reinforcing materials. Bead: The tire bead contains steel wires wrapped by steel cords that hold the tire onto the rim. Bias Ply Tire: A pneumatic tire in which the plies are laid at alternate angles less than 90 degrees to the centerline of the tread.

Cold Tire Pressure: The amount of air pressure in a tire, measured in pounds per square inch (psi) or kilopascals (kPa) before a tire has built up heat from driving. Curb Weight: This means the weight of a motor vehicle with standard and op- tional equipment including the maxi- mum capacity of fuel, oil and coolant, but without passengers and cargo. DOT Markings: A code molded into the sidewall of a tire signifying that the tire is in compliance with the U.S. Depart- ment of Transportation motor vehicle safety standards. The DOT code in- cludes the Tire Identification Number (TIN), an alphanumeric designator which can also identify the tire manufacturer, production plant, brand and date of production. GVWR: Gross Vehicle Weight Rating GAWR FRT: Gross Axle Weight Rating for the front Axle. GAWR RR: Gross Axle Weight Rating for the rear axle.

8 CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS

Intended Outboard Sidewall: The side of an asymmetrical tire, that must al- ways face outward when mounted on a vehicle. Kilopascal (kPa): The metric unit for air pressure. Load Index: An assigned number rang- ing from 1 to 279 that corresponds to the load carrying capacity of a tire. Maximum Inflation Pressure: The maximum air pressure to which a cold tire may be inflated. The maximum air pressure is molded onto the sidewall. Maximum Load Rating: The load rat- ing for a tire at the maximum permis- sible inflation pressure for that tire. Maximum Loaded Vehicle Weight: The sum of curb weight; accessory weight; vehicle capacity weight; and production options weight. Normal Occupant Weight: The num- ber of occupants a vehicle is designed to seat multiplied by 150 pounds (68
kg).

Occupant Distribution: Designated seating positions. Outward Facing Sidewall: The side of an asymmetrical tire that has a particu- lar side that faces outward when mounted on a vehicle. The side of the tire that contains a whitewall, bears white lettering or bears manufacturer, brand and or model name molding that is higher or deeper than the same mold- ings on the other sidewall of the tire. Passenger (P-Metric) Tire: A tire used on passenger cars and some light duty trucks and multipurpose vehicles. Recommended Inflation Pressure: Vehicle manufacturer's recommended tire inflation pressure as shown on the tire placard. Radial Ply tire: A pneumatic tire in which the ply cords that extend to the beads are laid at 90 degrees to the centerline of the tread. Rim: A metal support for a tire upon which the tire beads are seated.

Sidewall: The portion of a tire between the tread and the bead. Speed Rating: An alphanumeric code assigned to a tire indicating the maxi- mum speed at which a tire can operate. Traction: The friction between the tire and the road surface. The amount of grip provided. Tread: The portion of a tire that comes into contact with the road. Treadwear Indicators: Narrow bands, sometimes called "wear bars," that show across the tread of a tire when only 2/32
inch of tread remains. UTQGS: Uniform Tire Quality Grading Standards, a tire information system that provides consumers with ratings for a tire's traction, temperature and treadwear. Ratings are determined by tire manufacturers using government testing procedures. The ratings are molded into the sidewall of the tire.

Vehicle Capacity Weight: The number of designated seating positions multi- plied by 150 lbs. (68 kg) plus the rated cargo and luggage load. Vehicle Maximum Load on the Tire: Load on an individual tire due to curb and accessory weight plus maximum occupant and cargo weight. Vehicle Normal Load on the Tire: That load on an individual tire that is determined by distributing to each axle its share of the curb weight, accessory weight, and normal occupant weight and dividing by 2. Vehicle Placard: A label permanently attached to a vehicle showing the origi- nal equipment tire size and recom- mended inflation pressure.

CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS

I040A01O-AAT

SNOW TIRES If you equip your car with snow tires, they should be the same size and have the same load capacity as the original tires. Snow tires should be installed on all four wheels; otherwise, poor han- dling may result. Snow tires should carry 4 psi (28 kPa) more air pressure than the pressure recommended for the standard tires on the tire label on the driver's side of the center pillar , or up to the maximum pressure shown on the tire sidewall, whichever is less. Do not drive faster than 75 mph (120
km/h) when your car is equipped with snow tires.

I040B01JM-AAT

ALL SEASON TIRES Hyundai specifies all season tires on some models to provide good perfor- mance for use all year round, including snowy and icy road conditions. All sea- son tires are identified by ALL SEASON and/or M+S (Mud and Snow) on the tire sidewall. Snow tires have better snow traction than all season tires an may be more appropriate in some areas.

I040C01JM-AAT

SUMMER TIRES Hyundai specifies summer tires on some models to provide superior performance on dry roads. Summer tire performance is substantially reduced in snow and ice. Summer tires do not have the tire traction rating M+S (Mud and Snow) on the tire side wall. If you plan to operate your vehicle in snowy or icy conditions, Hyundai recommends the use of snow tires or all season tires on all four wheels.

8 CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS 10

I050A02O-AAT

TIRE CHAINS Tire chains, if necessary, should be installed on the front wheels. If your vehicle is equipped with 4WD (four wheels drive), be sure to install the chains on all wheels. Be sure that the chains are installed in accordance with the manufacturer's instructions. To minimize tire and chain wear, do not continue to use tire chains when they are no longer needed.

WARNING:

o When driving on roads covered with snow or ice, drive at less than 20 mph.

o Use the SAE "S" class or wire &

plastic chains.

o Don't use a tire chains to the ve- hicle which aluminium wheels are installed to keep the wheels. If it is on unavoidable circumstances, use a wire chains.

WARNING:

o Use wire chains less than 15mm to prevent damage to the chain's connection.

o If you have noise caused by chains contacting the body, retighten the chain to avoid contact with the vehicle body.

o To prevent body damage, retighten the chains after driving 0.3~0.6
miles.

I060A02O-AAT

TIRE ROTATION

Spare tire

HA1409

Tires should be rotated every 7,500
miles (12,000 km). If you notice that tires are wearing unevenly between ro- tations, have the car checked by a Hyundai dealer so the cause may be corrected. After rotating, adjust the tire pressures and be sure to check wheel nut torque.

CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS

11

I080A01A-AAT

TIRE TRACTION Tire traction can be reduced if you drive on worn tires, tires that are improperly inflated or on slippery road surfaces. Tires should be replaced when tread wear indicators appear. To reduce the possibility of losing control, slow down whenever there is rain, snow or ice on the road.

WARNING:

Do not mix bias-ply and radial-ply under any circumstances. This may cause unusual handling characteris- tics that could result in death, seri- ous injury, or property damage.

I070A01A-AAT

TIRE BALANCING

A tire that is out of balance may affect handling and tire wear. The tires on your Hyundai were balanced before the car was delivered but may need balancing again during the years you own the car. Whenever a tire is dismounted for re- pair, it should be rebalanced before being reinstalled on the car.

I090A02JM-AAT

WHEN TO REPLACE TIRES

0.06 in. (1.6 mm)

Tread wear indicator

HSM5013
The original tires on your car have tread wear indicators. The location of tread wear indicators is shown by the "TWI" or " " marks, etc., The tread wear indicators appear when the tread depth is 0.06 in. (1.6 mm). The tire should be replaced when these appear as a solid bar across two or more grooves of the tread. Always replace your tires with those of the recommended size. If you change wheels, the new wheel's rim width and offset must meet Hyundai specification.

8 CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS 12

! WARNING:

o Driving on worn-out tires is dan- gerous! Worn-out tires can cause loss of braking effectiveness, steering control and traction. When replacing tires, never mix radial and bias ply tires on the same car. If you replace radial tires with bias- ply tires, they must be installed in sets of four.

o Wheels that do not meet Hyundai's dimensional specifications may fit poorly and result in damage to the vehicle, including broken wheel studs.

WARNING:

o Your vehicle is equipped with tires designed to provide for safe ride and handling capability. Do not use a size and type of tire and wheel that is different from the one that is originally installed on your vehicle. It can affect the safety and performance of your vehicle, which could lead to handling fail- ure or rollover and serious injury. When replacing the tires, be sure to equip all four tires with the tire and wheel of the same size, type, tread, brand and load-carrying capacity. If you nevertheless de- cide to equip your vehicle with any tire/wheel combination not rec- ommended by Hyundai for off- road driving, you should not use these tires for highway driving.

I090B01JM-AAT

TIRE MAINTENANCE In addition to proper inflation, correct wheel alignment helps to decrease tire wear. If you find a tire is worn unevenly, have your dealer check the wheel align- ment.

When you have new tires installed, make sure they are balanced. This will increase vehicle ride comfort and tire life. Additionally, a tire shoud always be rebalanced if it is removed from the wheel.

CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS

WARRANTIES FOR YOUR HYUNDAI VEHICLE

13

I110A01A-AAT SHOP MANUAL

A Hyundai Shop Manual is available from your authorized Hyundai dealer. It's written for pro- fessional technicians, but is simple enough for most mechanically-inclined owners to under- stand.

I120A02A-AAT o New vehicle 60 Months/60,000 Miles Limited

Warranty.

o New vehicle 120 Months/100,000 Miles Lim- ited Powertrain Warranty (original owner only).

o Anti-Perforation Limited Warranty o Emission Defect Warranty - Federal Vehicle o California Emission Control System War-

ranty (if applicable)

o Emission Performance Warranty Federal

o Replacement Parts and Accessories Lim-

vehicle

ited Warranty

NOTE: Detailed warranty information is provided in your Hyundai Owner's Handbook.

SPARE TIRE AND TOOLS

I100A02E-AAT

D060B01O Your Hyundai is delivered with the fol- lowing:

Spare tire and wheel Wheel nut wrench, Wrench bar Jack

8 CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS 14

CONSUMER INFORMATION

I130A01A-AAT This consumer information has been prepared in accordance with regulations issued by the National Highway Traffic Safety Administration of the U.S. Department of Transportation. It provides the purchasers and/or prospective purchasers of Hyundai automobiles with infor- mation on uniform tire quality grading. Your Hyundai dealer will help answer any questions you may have as you read this information.

Traction AA, A, B, C - The traction grades, from highest to lowest, are AA, A, B, and C. Those grades represent the tire's ability to stop on wet pave- ment as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction per- formance.

! WARNING:

The traction grade assigned to this tire is based on straight-ahead brak- ing traction tests, and does not in- clude acceleration, cornering, hy- droplaning, or peak traction charac- teristics.

I130B04A-AAT

Tire Quality Grading Department of Transportation quality grades - All passenger vehicle tires must conform to Federal Safety Stan- dards in addition to these grades. These quality grades are molded on the sidewall.

Treadwear - The treadwear grade is a comparative rating based on the wear rate of the tire when tested under con- trolled conditions on a specified gov- ernment test course. For example, a tire graded 150 would wear one and a half (1 - 1/2) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to varia- tions in driving habits, service prac- tices and differences in road character- istics and climate.

CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS

15

Temperature A, B, C - The tempera- ture grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat when tested under con- trolled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law.

! WARNING:

The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Exces- sive speed, underinflation, or exces- sive loading, either separately or in combination, can cause heat buildup and possible tire failure.

Uniform Tire Quality Grading - Qual- ity grades can be found on the tire sidewall between the tread shoulder and the maximum section width. For example : Treadwear 200 Traction AA Tempera- ture A

I130D04A-AAT Hyundai motor vehicles are designed and manu- factured to meet or exceed all applicable safety standards.

For your safety, however, we strongly urge you to read and follow all directions in this Owner's Manual, particularly the information under the headings "NOTE", "CAUTION" and "WARN- ING".

If, after reading this manual, you have any questions regarding the operation of your ve- hicle, please contact your nearest Hyundai Motor America Regional Office as listed below:

Eastern Region : Connecticut, Delaware, Maine, Maryland, Massachusetts, New Hamp- shire, New Jersey, New York, Pennsylvanina, Rhode Island, Vermont, Virginia, West Virginia.

Eastern Region 1100 Cranbury South River Road Jamesburg, NJ 08831
(800) 633-5151

8 CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS 16

Western Region: Alaska, Hawaii, Arizona, California, ldaho, Montana, Nevada, Oregon, Texas, Utah, Washington.

Western Region 10550 Talbert Avenue P.O.Box 20850
Fountain Valley, California 92728-0850
(800) 633-5151

Southern Region: Florida, Georgia, North Caro- lina, South Carolina.

Southern Region 270 Riverside Parkway, Suite A Austell, GA 30168
(800) 633-5151

South Central Region: Alabama, Arkansas, Colorado, Kansas, Louisiana, Mississippi, Mis- souri, New Mexico, Oklahoma, Tennessee, Texas, Wyoming.

South Central Region 1421 South Beltline Road, Suite 400

Coppell, TX 75019
(800) 633-5151

Central Region: Illinois, Indiana, lowa, Ken- tucky, Michigan, Minnesota, Nebraska, North Dakota, South Dakota, Ohio, Wisconsin.

Central Region 1705 Sequoia Drive Aurora, Illinois 60506
(800) 633-5151

REPORTING SAFETY DEFECTS

I130C02A-AAT If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying HYUNDAI MOTOR AMERICA. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy cam- paign. However, NHTSA cannot become involved in individual problems between you, your dealer, or HYUNDAI MOTOR AMERICA. To contact NHTSA, you may call the Ve- hicle Safety Hotline toll-free at 1-888-327- 4236 (TTY: 1-800-424-9153); go to http:// www.safercar.gov; or write to: Administra- tor, NHTSA, 400 Seventh Street, SW., Washington, DC 20590. You can also obtain other information about motor ve- hicle safety from http://www.safercar.gov.

BINDING ARBITRATION

I140A01A-AAT Any claim or dispute you may have related to your vehicle's warranty or the duties contemplated under the warranty, including claims related to the refund or partial refund of your vehicle's purchase price (excluding personal injury or prod- uct liability claims), shall be resolved by binding arbitration. Binding arbitra- tion shall be administered by and through