Login- 2011 Hyundai Accent Owners Manuals
- Hyundai Accent Owners Manuals
- 2005 Hyundai Accent Owners Manuals
- Hyundai Accent Owners Manuals
- 2003 Hyundai Accent Owners Manuals
- Hyundai Accent Owners Manuals
- 2009 Hyundai Accent Owners Manuals
- Hyundai Accent Owners Manuals
- 2008 Hyundai Accent Owners Manuals
- Hyundai Accent Owners Manuals
- 2004 Hyundai Accent Owners Manuals
- Hyundai Accent Owners Manuals
- 2007 Hyundai Accent Owners Manuals
- Hyundai Accent Owners Manuals
- 2012 Hyundai Accent Owners Manuals
- Hyundai Accent Owners Manuals
- Download PDF Manual
-
the foot brake and pull the praking brake lever slightly. Secondly, depress the re- lease button and lower the parking brake lever while holding the button.
HIGH-MOUNTED REAR STOP LIGHT
B550A01S-GAT 4 Door
3 Door
B550A01MC
B550A01MC-1
In addition to the lower-mounted rear stop lights on either side of the car, the high mounted rear stop light in the center of the rear window or inserted in the rear spoiler also lights when the brakes are applied.HOOD RELEASE
B570A01MC-GAT
FEATURES OF YOUR HYUNDAI FEATURES OF YOUR HYUNDAI
93
93Before closing the hood, return the sup- port rod to its clip to prevent it from rattling. Lower the hood until it is about 1 ft. (30
cm) above the closed position and let it drop. Make sure that it locks into place.CAUTION:
Make sure that the support rod has been released prior to closing the hood.
OMC025019
1. Pull the release knob to unlatch thehood.
3. Pull the support rod from the hood.
B570A01MC
2. Pull the secondary latch lever up and
lift the hood.
OMC025020
B570A02MC 4. Hold the hood open with the support
rod.
! WARNING:
o Always double check to be sure that the hood is firmly latched before driv- ing away. If it is not latched, the hood could fly open while the vehicle is being driven, causing a total loss of visibility, which might result in an accident.
o The support rod must be inserted completely into the hole provided in the hood whenever you inspect the engine compartment. This will pre- vent the hood from falling and possi- bly injuring you.
o Do not move the vehicle with the hood in the raised position, as vision is obstructed and the hood could fall or be damaged.
1FEATURES OF YOUR HYUNDAI 94
REMOTE FUEL-FILLER LID RELEASE
B560A02MC-AAT
OMC025017
The fuel-filler lid must be opened from inside the vehicle by pulling up on the fuel-filler lid opener located on the front floor area on the left side of the car.4 Door
NOTE: If the fuel-filler lid will not open because ice has formed around it, tap lightly or push on the lid to break the ice and release the lid. Do not pry on the lid. If necessary, spray around the lid with an approved de-icer fluid (do not use radia- tor anti-freeze) or move the vehicle to a warm place and allow the ice to melt.
3 Door
OMC041600
OMC041601
! WARNING:
o Gasoline vapors are dangerous. Before refueling, always stop the engine and never smoke or allow sparks and open flames near the filler area.
o Never operate your vehicle without a filler cap properly installed, flam- mable vapors and gasoline could leak out in dangerous situations such as a collision or rollover. If the filler cap must be replaced, only use genu- ine Hyundai replacement parts.
o After refueling, make sure the fuel cap is installed securely to prevent fuel spillage in the event of an acci- dent.
o Tighten the cap until it clicks one "light will
time, otherwise the " illuminate.
o If you open the fuel filler cap during high ambient temperatures, a slight "pressure sound" may be heard. This is normal and not a cause for concern. Whenever you open the fuel filler cap, turn it slowly.
o Do not "top off" after the nozzle au- tomatically shuts off when refueling.
! WARNING:
o Automotive fuels are flammable/ex- plosive materials. When refueling, please note the following guidelines carefully. Failure to follow these guidelines may result in severe per- sonal injury, severe burns or death by fire or explosion. - Read and follow all warnings posted
at the gas station facility.
- Before refueling, note the location of the Emergency Gasoline Shut- Off, if available, at the gas station facility.
- Before touching the fuel nozzle or fuel filler cap, you should eliminate potentially dangerous static elec- tricity discharge by touching an- other metal part of the front of the vehicle, a safe distance away from the fuel filler neck, nozzle, or other gas source.
- Do not get back into a vehicle once you have begun refueling. Do not touch, rub or slide against any item or fabric (polyester, satin, nylon, etc.) capable of producing static electricity. Static electricity dis- charge can ignite fuel vapors re- sulting in explosion.
FEATURES OF YOUR HYUNDAI FEATURES OF YOUR HYUNDAI
95
95! WARNING:
If you must re-enter the vehicle, you should once again eliminate potentially dangerous static elec- tricity discharge by touching a metal part of the vehicle, away from the fuel filler neck, nozzle or other gasoline source.
- When using a portable fuel con- tainer be sure to place the con- tainer on the ground prior to refu- eling. Static electricity discharge from the container can ignite fuel vapors causing a fire. Once refu- eling has begun, contact with the vehicle should be maintained until the filling is complete. Use only portable fuel containers designed to carry and store gasoline.
- Do not use cellular phones around a gas station or while refueling any vehicle. Electric current and/or electronic interference from cellu- lar phones can potentially ignite fuel vapors causing a fire. If you must use your cellular phone use it in a place away from the gas station.
1FEATURES OF YOUR HYUNDAI 96
! WARNING:
- When refueling always shut the engine off. Sparks produced by electrical components related to the engine can ignite fuel vapors causing a fire. Always insure that the engine is OFF before and dur- ing refueling. Once refueling is complete, check to make sure the fuel filler cap and door are se- curely closed, before starting the engine.
- Do not light any fire around a gas station. DO NOT use matches or a lighter and DO NOT SMOKE or leave a lit cigarette in your vehicle while at a gas station especially during refueling. Automotive fuel is highly flammable and can, when ignited, result in explosion by flames. If a fire breaks out during refueling, leave the vicinity of the vehicle, and immediately contact the man- ager of the gas station or contact the police and local fire depart- ment. Follow any safety instruc- tions they provide.
TRUNK LID/TAIL GATE
B540A01MC-GAT
Trunk Lid (4 Door)
WARNING:
The trunk lid or the tail gate should al- ways be kept completely closed while the vehicle is in motion. If it is left open or ajar, poisonous exhaust gases may en- ter the car resulting in serious illiness or death to the occupants. See additional warnings concerning exhaust gases on page 2-2.
OMC025010
o The trunk lid is opened by first turning the key clockwise to release the lock, then raising the door manually.
o To close, lower the trunk lid, then press down on it until it locks. To be sure the trunk lid is securely fastened, try to pull it up again.
Tail Gate (3 Door)
B540D01MC-GAT
Remote Trunk Lid Release (4 Door) (If Installed)
B540B02MC-AAT
Trunk Lid Emergency Latch Release (4 Door)
FEATURES OF YOUR HYUNDAI FEATURES OF YOUR HYUNDAI
97
97OMC025010-1
o To open the tail gate, unlock it by turning the key clockwise, then pull the outside handle toward you.
o To close, lower the tail gate and shut firmly to engage the latch. Lock the tail gate by turning the key counterclock- wise.
o If the vehicle is equipped with central door locking, the tail gate can be locked without a key. Push the front portion of the central door locking switch after closing the tail gate.
o If the tail gate is open when the front portion of the central door locking switch is pushed, the tail gate will be locked when it is fully closed.
OMC025011
To open the trunk lid without using the key, pull up the lid release lever. To close, lower the trunk lid, then press down on it until it locks. To be sure the trunk lid is securely fastened, check by trying to pull it up again.OMC025013
Your vehicle is equipped with a glow-in- the dark emergency trunk release lever located inside the trunk. It will glow after the trunk is closed. When pulled, this lever will release the trunk latch mecha- nism and open the trunk.! WARNING:
The trunk lid should always be kept com- pletely closed while the vehicle is in motion. If it is left open or ajar, exhaust gases may enter the car and serious illness may result.
1FEATURES OF YOUR HYUNDAI 98
! WARNING:
o If a person becomes locked in the trunk, pull the emergency trunk re- lease lever of the inside panel in the trunk to open the trunk lid.
o Keep cars locked and keys out of the reach of children. HYUNDAI recom- mends parents teach children about the emergency trunk release lever in their vehicle and how to open the trunk lid if they are accidentally locked in the trunk.
LUGGAGE NET
B540D02O-AAT
(If Installed) Type A
CAUTION:
To prevent damage to the goods or the vehicle, care should be taken when car- rying fragile or bulky objects in the lug- gage compartment.
Type B
1JBA3113
! WARNING:
Avoid eye injury. DO NOT overstretch the luggage net. ALWAYS keep your face and body out of its recoil path. DO NOT use when the luggage net straps have visible signs of wear or damage.
B540D01MC When loading the objects in the luggage compartment, use the four rings located in the luggage compartment to attach the luggage net as shown illustration. This will help prevent the objects from sliding.
CARGO AREA COVER
FLOOR MAT ANCHOR(S)
B650A01A-GAT
(3 Door)
B571A03Y-AAT
(If Installed)
B650A01MC
OXM049228
Nothing should be carried on top of the luggage cover. Loose materials could result in injury to vehicle occupants dur- ing sudden braking.
When using a floor mat on the front floor carpet, make sure it attaches to the floor mat anchor(s) in your vehicle. This keeps the floor mat from sliding forward.
FEATURES OF YOUR HYUNDAI FEATURES OF YOUR HYUNDAI
99
99WARNING:
The following must be observed when installing ANY floor mat to the vehicle. o Ensure that the floor mats are se- curely attached to the vehicle's floor mat anchor(s) before driving the vehicle.
o Do not use ANY floor mat that cannot be firmly attached to the vehicle's floor mat anchors.
o Do not stack floor mats on top of one another (e.g. all-weather rubber mat on top of a carpeted floor mat). Only a single floor mat should be installed in each position.
IMPORTANT - Your vehicle was manu- factured with driver's side floor mat an- chors that are designed to securely hold the floor mat in place. To avoid any interference with pedal operation, HYUNDAI recommends that only the HYUNDAI floor mat designed for use in your vehicle be installed.
1FEATURES OF YOUR HYUNDAI 100
SUN VISOR
B580A02MC-AAT
B580A01MC
Your Hyundai is equipped with sun visors to give the driver and front passenger either frontal or sideward shade. To re- duce glare or to shut out direct rays of the sun, turn the sun visor down.
B580A02MC
Ticket holders and vanity mirrors are pro- vided on the back of the sun visor for the driver and the front passenger (If Installed).
NOTE: The Supplemental Restraint System (SRS) label containing useful informa- tion can be found on the topside of sun visor.
! WARNING:
o Do not place the sun visor in such a manner that it obscures visibility of the roadway, traffic or other objects.
! WARNING:
o Do not move the sun visor out to cover the side window if there is an item attended to it such as a garage door remote control, pens, air fresh- eners or the like. These objects could cause injury if the curtain airbag is deployed.
B500B01B-GAT
Illuminated Vanity Mirror (If Installed)
Opening the lid of the vanity mirror will automatically turn on the mirror light.
OMC025100
B580C01JM-AAT
Sun Visor Extender (If Installed)
B600A01A-AAT
(If Installed)
STEERING WHEEL TILT LEVER
FEATURES OF YOUR HYUNDAI FEATURES OF YOUR HYUNDAI
101
101HORN
B610B01L-GAT
B580C01MC
OMC025045
Your vehicle is equipped with sun visor extenders that may be used when the visor is in the side glass position.
To Adjust the Steering Wheel: 1. Push the lever downward to unlock. 2. Raise or lower the steering wheel to
the desired position.
3. After adjustment, securely tighten the
lever by pulling it upward.
Press the pad on the steering wheel to sound the horn.
OMC025046
WARNING:
Do not attempt to adjust the steering wheel while driving as this may result in loss of control of the vehicle which may cause serious injury or death.
VOL Switch o Press the upper portion VOL switch to
o Press the lower portion VOL switch to
increase volume.
decease volume.
1FEATURES OF YOUR HYUNDAI 102
AUDIO REMOTE CONTROL SWITCH
B610A02MC-GAT
(If Installed)
NOTE: o If there is no CD or the auxiliary device is not connected, the mode cannot be converted to the CD, CDC or AUX mode.
o The CD, CDC or AUX mode is not
available for some audio models.
SEEK Switch Press the SEEK switch 1 sec. or more.
1. RADIO mode When the upper portion SEEK is pressed, the unit will automatically tune to the next higher frequency and when the lower portion SEEK is pressed, it will automati- cally tune to the next lower frequency.
2. CD (Compact Disc)/CDC (Com- pact Disc Changer)/AUX mode
o Press the upper portion SEEK once to skip forward to the beginning of the next track.
o Press the lower portion SEEK once to skip back to the beginning of the track.
OMC029110
The steering wheel may incorporate au- dio control buttons.NOTE: Do not operate audio remote control switches simultaneously.
MODE Switch Each press of the switch changes the display as follows:
RADIO (FM1→FM2→AM)→CD*→CDC* → → AUX*
* : if installed
FEATURES OF YOUR HYUNDAI FEATURES OF YOUR HYUNDAI
103
103E090100AMC
To set cruise control speed:
OMC039300
1. Push the CRUISE ON-OFF button on the steering wheel to turn the system on. The CRUISE indicator light in the instrument cluster will illuminate.
2. Accelerate to the desired speed, which must be more than 25 mph (40 km/h).
CRUISE CONTROL SYSTEM
E090000AMC
(If Installed) The cruise control system allows you to program the vehicle to maintain a con- stant speed without resting your foot on the accelerator pedal. This system is designed to function above approximately 25 mph (40 km/h).
! WARNING:
o If the cruise control is left on, (CRUISE indicator light in the instru- ment cluster illuminated) the cruise control can be switched on acciden- tally. Keep the cruise control sys- tem off (CRUISE indicator light OFF) when the cruise control is not in use, to avoid inadvertently setting a speed.
o Use the cruise control system only when traveling on open highways in good weather.
o Do not use the cruise control when it may not be safe to keep the car at a constant speed, for instance, driving in heavy or varying traffic, or on slippery (rainy, icy or snow-covered) or winding roads or over 6% up-hill or down-hill roads.
! WARNING:
o Pay particular attention to the driv- ing conditions whenever using the cruise control system.
o Be careful when driving downhill using the cruise control system, which may increase the vehicle speed.
CAUTION:
During cruise-speed driving of a manual transaxle vehicle, do not shift into neu- tral without depressing the clutch pedal, since the engine will be overrevved. If this happens, depress the clutch pedal or release the cruise control ON/OFF switch.
NOTE: During normal cruise control operation, when the -/SET switch is activated or reactivated after applying the brakes, the cruise control will energize after ap- proximately 3 seconds. This delay is normal.
1FEATURES OF YOUR HYUNDAI 104
NOTE: On steeper hills, with a Manual Transaxle, the cruise control may be unable to main- tain the set speed. The driver should downshift as necessary. Press the "RES/+" button to resume the cruise control at the set speed in the new gear. After cresting the hill, upshift, and press the "RES/+" again. If the speed drops ~ 9 mph below the set speed, the cruise control will cancel. If it cancels, shift to the appropriate gear, and press the "RES/+" to resume the cruse control.
E090200AMC
To increase cruise control set speed:
OMC039302
Follow either of these procedures: o Push the RES/+ switch and hold it. Your vehicle will accelerate. Release the switch at the speed you want.
o Push the RES/+ switch and release it immediately. The cruising speed will increase by 1 mph (1.6 km/h) each time the RES/+ switch is operated in this manner.
OMC039301
3. Push the -/SET switch, and release it at the desired speed. The SET indicator light in the instrument cluster will illu- minate. Release the accelerator at the same time. The desired speed will automatically be maintained.On a steep grade, the vehicle may slow down or speed up slightly while going downhill.
E090300AMC
To decrease the cruising speed:
E090400AUN
To temporarily accelerate with the cruise control on: If you want to speed up temporarily when the cruise control is on, depress the ac- celerator pedal. Increased speed will not interfere with cruise control operation or change the set speed. To return to the set speed, take your foot off the accelerator.
OMC039301
Follow either of these procedures: o Push the -/SET switch and hold it. Your vehicle will gradually slow down. Re- lease the switch at the speed you want to maintain.
o Push the -/SET switch and release it immediately. The cruising speed will decrease by 1 mph (1.6 km/h) each time the -/SET switch is operated in this manner.
FEATURES OF YOUR HYUNDAI FEATURES OF YOUR HYUNDAI
105
105E090500AMC
To cancel cruise control, do one of the following:
OMC039303
o Press the brake pedal. o Press the clutch pedal with a manual
o Shift into N (Neutral) with an automatic
transaxle.
transaxle.
o Press the CANCEL switch located on
the steering wheel.
o Decrease the vehicle speed lower than the memory speed by 9 mph (15 km/h). o Decrease the vehicle speed to less than approximately 25 mph (40 km/h).
1FEATURES OF YOUR HYUNDAI 106
Each of these actions will cancel cruise control operation (the SET indicator light in the instrument cluster will go off), but it will not turn the system off. If you wish to resume cruise control operation, push the RES/+ switch located on your steer- ing wheel. You will return to your previ- ously preset speed.
E090600AMC
To resume cruising speed at more than approximately 25 mph (40 km/h):
E090700AUN
To turn cruise control off, do one of the following:
OMC039302
If any method other than the CRUISE ON- OFF switch was used to cancel cruising speed and the system is still activated, the most recent set speed will automati- cally resume when the RES/+ switch is pushed. It will not resume, however, if the vehicle speed has dropped below ap- proximately 25 mph (40 km/h).
OMC039300
o Push the CRUISE ON-OFF button (the CRUISE indicator light in the instru- ment cluster will go off).o Turn the ignition off. Both of these actions cancel cruise con- trol operation. If you want to resume cruise control operation, repeat the steps pro- vided in “To set cruise control speed” on the previous page.
FEATURES OF YOUR HYUNDAI FEATURES OF YOUR HYUNDAI
107
107AUX, USB AND iPod® PORT
D281400AFD
(If Installed)
OMC029033C If your vehicle has an aux and/or USB(universal serial bus) port or iPod port, you can use an aux port to connect audio devices, a USB port to plug in a USB, and an iPod port to plug in an iPod. When using an iPod through the vehicle's Audio System, a Hyundai adapter cable is required in order to receive all func- tions, which can be purchased at your local Hyundai dealership.
NOTE: When using a portable audio device con- nected to the power outlet, noise may occur during playback. If this happens, use the power source of the portable audio device.
❈ iPod® is a trademark of Apple Inc.
1FEATURES OF YOUR HYUNDAI 108
HEATING AND COOLING CONTROL
B710A01TB-GAT
(If Installed)
B710B01MC-AAT
Center Ventilator/Side Ventilator
B710B01MC
The center ventilators are located in the middle of the dashboard. The side venti- lators are located on each side of dash- board. To change the direction of the air flow, move the knob in the center of the vent up-and-down and side-to-side. The vents are opened when the vent " position. The knob is moved to " vents are closed when the vent knob is ". Keep these vents clear of moved to " any obstructions.
1. Side Defroster Nozzle 2. Side Ventilator 3. Windshield Defroster Nozzle 4. Center Ventilator
B710A01MC
HEATING AND VENTILA- TION
B670A02A-GAT
(If Installed)
FEATURES OF YOUR HYUNDAI FEATURES OF YOUR HYUNDAI
109
109B670B01A-AAT
Fan Speed Control (Blower Control)
B670C03A-AAT
Air Intake Control
B670A01MC-D
1. Temperature control 2. Air conditioning switch (If Installed) 3. Air intake control switch 4. Air flow control 5. Fan speed control
OMC025083
This is used to turn the blower fan on or off and to select the fan speed. This blower fan speed, and therefore the volume of air delivered from the system, may be controlled manually by setting the blower control between the "1" and "4" positions.
B670C02MC This is used to select fresh outside air or recirculating inside air.
Fresh Recirculation
" mode selected, air enters With the " the vehicle from outside and is heated or cooled according to the other functions selected. " mode selected, air from With the " within the passenger compartment is drawn through the heating system and heated or cooled according to the other functions selected.
1FEATURES OF YOUR HYUNDAI 110
NOTE: It should be noted that prolonged opera- tion of the intake air system in " mode will give rise to misting of the windshield and side windows and the air within the passenger compartment will become stale. In addition prolonged use of the air conditioning with the " mode selected may result in the air within the passenger compartment becoming excessively dry.
B670D03MC-AAT
Air Flow Control
B670D01MC-D
Face-Level
B670D02MC
This is used to direct the flow of air. Air can be directed to the floor, instrument panel outlets, or windshield. Five sym- bols are used to represent Face, Bi- Level, Floor, Floor-Defrost and Defrost air position.
Selecting the "Face" mode will cause air to be discharged through the face level vents.
FEATURES OF YOUR HYUNDAI FEATURES OF YOUR HYUNDAI
111
111B670D03MC
B670D04MC
B670D05MC
Bi-Level
Floor-Level
Floor-Defrost Level
Air is discharged through the face vents and the floor vents.
Air is discharged through the floor vents, windshield defroster nozzle, side defroster nozzle and side ventilator.
Air is discharged through the windshield defroster nozzle, the floor vents, side defroster nozzle and side ventilator. In vehicle equipped with A/C, the A/C will automatically be turned on and "Fresh" mode will be activated.
1FEATURES OF YOUR HYUNDAI 112
B670D06MC
Defrost-Level
Air is discharged through the windshield defroster nozzle, side defroster nozzle, side ventilator. In vehicle equipped with A/C, the A/C will automatically be turned on and "Fresh' mode will be activated.
B670E02A-AAT
Temperature Control
NOTE: In vehicle equipped with A/C, when "Floor- Defrost" or "Defrost" modes are se- lected, the A/C will automatically be turned on and "Fresh" mode will be ac- tivated to help dry the air. The A/C will not turn off and "Recircula- tion" mode will not be selected until the air flow control is set to the another mode other than the "Floor-Defrost" and the "Defrost" mode.
Cool
Warm
B670E01MC
This control is used to adjust the degree of heating or cooling desired.
FEATURES OF YOUR HYUNDAI FEATURES OF YOUR HYUNDAI
113
113HEATING CONTROLS
BI-LEVEL HEATING
VENTILATION
B690A02A-AAT
B700A02A-AAT
B710A01A-AAT
B690A01MC-D
B700B01MC-D
B710A01MC-D
For normal heating operation, set the air intake control to the fresh air ( ) position and the air flow control to the floor ( ) position. For faster heating, the air intake control should be set in the recirculate ( position. If the windows fog up, set the air flow control to the defrost ( ) position (The A/C will automatically be turned on and "Fresh" mode will be activated.). For maximum heat, move the tempera- ture control to "Warm".
Your Hyundai is equipped with bi-level heating controls. This makes it possible to have cooler air from the dashboard vents and warmer air from the floor out- lets at the same time. To use this feature:
o Set the air intake control to the fresh air
o Set the air flow control at the bi-level
o Adjust the fan speed control to the
o Set the temperature control between
"Cool" and "Warm".
( ) position.
( ) position.
desired speed.
To operate the ventilation system:
o Set the air intake control to "Fresh"
mode ( ).
o To direct all intake air to the dashboard
vents, set the air flow control to the ( position.
o Adjust the fan speed control to the
desired speed.
o Set the temperature control between
"Cool" and "Warm".
1FEATURES OF YOUR HYUNDAI 114
DEFROSTING/DEFOGGING
B720A01MC-AAT
B720A01MC-D Use the heating/ventilation system to defrost or defog the windshield:
To remove interior fog on the wind- shield: o Set the air flow control to the defrost ) position (The A/C will automati- cally be turned on and "Fresh" mode will be activated.).
o Set the temperature control to the de-
o Set the fan speed control between "1"
sired position.
and "4" position.
NOTE: When the A/C is operated continuously ) or defrost on the floor-defrost level ( ), it may cause fog to form on level ( the exterior windshield. If this occurs, set the air flow control to the face level ) and fan speed control to the position ( low position.
B720A02MC-D
To remove the frost or exterior fog on the windshield: o Set the air flow control to the defrost ) position (The A/C will automati- cally be turned on and "Fresh" mode will be activated.).
o Set the temperature control to warm. o Set the fan speed control to position
"3" or "4".
B730A01L-AAT
Operation Tips o To keep dust or unpleasant fumes from entering the car through the ven- tilation system, temporarily set the air ) position. intake control at the ( Be sure to return the control to the ( ) position when the irritation has passed to keep fresh air in the vehicle. This will help keep the driver alert and comfortable.
o Air for the heating/cooling system is drawn in through the grilles just ahead of the windshield. Care should be taken that these are not blocked by leaves, snow, ice or other obstructions.
o To prevent interior fog on the wind- shield, set the air intake control to the ) position, fan speed to fresh air ( the desired position, turn on the air conditioning system, and adjust tem- perature control to desired tempera- ture.
AIR CONDITIONING SYSTEM
FEATURES OF YOUR HYUNDAI FEATURES OF YOUR HYUNDAI
115
115B740A01A-AAT
(If Installed) Air Conditioning Switch
B740B02A-AAT
Air Conditioning Operation (Cooling)
B740A01MC-D
B740B01MC-D
The air conditioning is turned on by push- ing the A/C button on the heating/air conditioning control panel.
To use the air conditioning to cool the interior:
o Turn on the fan control switch. o Turn on the air conditioning switch by
pushing in on the switch. The air conditioning indicator light should come on at the same time.
o Set the temperature control to "Cool". ("Cool" provides maximum cooling. The temperature may be moderated by moving the control toward "Warm".)
o Adjust the fan control to the desired speed. For greater cooling, turn the fan control to one of the higher speeds or )position temporarily select the ( on the air intake control.
1FEATURES OF YOUR HYUNDAI 116
B740C01MC-AAT
De-Humidified Heating
B740C01MC-D
For dehumidified heating: o Turn on the fan control switch. o Push the air conditioning switch. The air conditioning indicator light should come on at the same time.
o Set the air intake control switch to the
fresh air (
) position.
o Adjust the fan control to the desired
speed.
o For more rapid action, set the fan at
one of the higher speeds.
o Adjust the temperature control to pro-
vide the desired amount of warmth.
B740D01A-AAT
Operation Tips o If the interior of the car is hot when you first get in, open the windows for a few minutes to expel the hot air.
o When you are using the air condition- ing system, keep all windows closed to keep hot air out.
o When moving slowly, as in heavy traf-
fic, shift to a lower gear. This increases engine speed, which in turn increases the speed of the air conditioning compressor.
o On steep grades, turn the air condi- tioning off to avoid the possibility of the engine overheating.
o During winter months or in periods when the air conditioning is not used regularly, run the air conditioning once every month for a few minutes. This will help circulate the lubricants and keep your system in peak operat- ing condition.
B720A01MC-AAT DEFROSTING/DEFOGGING
FEATURES OF YOUR HYUNDAI FEATURES OF YOUR HYUNDAI
117
117OMC029102
OMC029103
Use the heating/ventilation system to defrost or defog the windshield:
To remove interior fog on the windshield; o Set the air flow control to the defrost ( ) position (The A/C will automatically be turned on and "Fresh" mode will be activated.).
o Set the temperature control to the desired position. o Set the fan speed control between "1" and "4" position.
To remove frost or exterior fog on the windshield; o Set the air flow control to the defrost ( ) position (The A/C will automatically be turned on and "Fresh" mode will be activated.).
o Set the temperature control to warm. o Set the fan speed control to position "3" or "4".
NOTE: When the A/C is operated continuously on the floor-defrost level ( ) or defrost level ( ), it may cause fog to form on the exterior windshield. If this occurs, set the air flow control to the face level position ( ) and fan speed control to the low position.
1FEATURES OF YOUR HYUNDAI 118
CLIMATE CONTROL AIR FILTER
B760A07A-AAT
(For evaporator and blow unit)
Outside air
Inside of a vehicle
Blower
Evaporator core
Filter
Inside air
B760A01MC
The climate control air filter is located in front of the evaporator unit behind the glove box. It operates to decrease the amount of pollutants entering the car. To replace the climate control air filter, refer to the page 6-16.
CAUTION:
o Replace the filter every 10,000 miles (15,000 km) or once a year. If the car is being driven in severe conditions such as dusty, rough roads, more frequent climate control air filter in- spections and changes are required. o When the air flow rate is decreased, the system should be checked at an authorized dealer.
STEREO SOUND SYSTEM
B750A02A-AAT
How Car Audio Works FM reception
AM reception
FM radio station
FEATURES OF YOUR HYUNDAI FEATURES OF YOUR HYUNDAI
119
119JBM002
JBM003
AM broadcasts can be received at greater distances than FM broadcasts. This is because AM radio waves are transmitted at low frequencies. These long, low fre- quency radio waves can follow the curva- ture of the earth rather than travelling straight out into the atmosphere. In addi- tion, they curve around obstructions so that they can provide better signal cover- age.
FM broadcasts are transmitted at high frequencies and do not bend to follow the earth's surface. Because of this, FM broad- casts generally begin to fade at short distances from the station. Also, FM sig- nals are easily affected by buildings, mountains, or other obstructions. These can result in certain listening conditions which might lead you to believe a prob- lem exists with your radio. The following conditions are normal and do not indicate radio trouble:
JBM001
AM and FM radio signals are broadcast from transmitter towers located around your city. They are intercepted by the radio antenna on your car. This signal is then received by the radio and sent to your car speakers. When a strong radio signal has reached your vehicle, the precise engineering of your audio system ensures the best pos- sible quality reproduction. However, in some cases the signal coming to your vehicle may not be strong and clear. This can be due to factors such as the distance from the radio station, close- ness of other strong radio stations or the presence of buildings, bridges or other large obstructions in the area.
1FEATURES OF YOUR HYUNDAI 120
JBM004
JBM005
o Fading - As your car moves away from the radio station, the signal will weaken and sound will begin to fade. When this occurs, we suggest that you select another stronger station.
o Flutter/Static - Weak FM signals or large obstructions between the trans- mitter and your radio can disturb the signal causing static or fluttering noises to occur. Reducing the treble level may lessen this effect until the distur- bance clears.
o Station Swapping - As an FM signal weakens, another more powerful sig- nal near the same frequency may be- gin to play. This is because your radio is designed to lock onto the clearest signal. If this occurs, select another station with a stronger signal.
o Multi-Path Cancellation - Radio sig- nals being received from several di- rections can cause distortion or flutter- ing. This can be caused by a direct and reflected signal from the same station, or by signals from two stations with close frequencies. If this occurs, select another station until the condition has passed.
Satellite radio reception
You may experience problems in receiv- ing XMTM satellite radio signals in the following situations.
SATELITE1
(cid:129)
(cid:129)
(cid:129) (cid:129)
(cid:129)
(cid:129)
If you are driving in a tunnel or a covered parking area. If you are driving beneath the top level of a multi-level freeway. If you drive under a bridge. If you are driving next to a tall vehicle (such as a truck or a bus) that block the signal. If you are driving in a valley where the surrounding hills or peaks block the signal from the satellite. If you are driving on a mountain road where the signal is blocked by moun- tains.
FEATURES OF YOUR HYUNDAI FEATURES OF YOUR HYUNDAI
121
121CARE OF DISCS
B850A02F-AAT
Proper Handling
B750B05Y-AAT
Using a cellular phone or a two-way radio When a cellular phone is used inside the vehicle, noise may be produced from the audio equipment. This does not mean that something is wrong with the audio equipment. In such a case, use the cellu- lar phone at a place as far as possible from the audio equipment.
(cid:129)
SATELITE2
If you are driving in an area with tall trees that block the signal (10m or more) ; for example, on a road through a dense forest.(cid:129) The signal can become weak in some areas that are not covered by the re- peater station network.
WARNING:
Hyundai recommends that you never use a cell phone while driving. This could result in loss of control, and an accident that may cause death, serious injury, or property damage. You must stop at a safe place to use a cellular phone.
Please note that these may be other unforeseen circumstances when there are problems with the reception of XMTM sat- ellite radio signal.
NOTE: Some states and cities have regulations prohibiting the use of cell phones while driving. You should be aware of the spe- cific requirements in your area.
B850A01L
Handle your disc as shown. Do not drop the disc. Hold the disc so you will not leave fingerprints on the surface. If the surface is scratched, it may cause the pickup to skip signal tracks. Do not affix tape, paper, or gummed labels on the disc. Do not write on the disc.
Damaged Disc Do not attempt to play damaged, warped or cracked discs. These could severely damage the playback mechanism.
1FEATURES OF YOUR HYUNDAI 122
Storage When not in use, place your discs in their individual cases and store them in a cool place away from the sun, heat, and dust. Do not grip or pull out the disc with your hand while the disc is being pulled into the unit by the self loading mechanism.
Keep Your Discs Clean
AUDIO SYSTEM
NOTE: If you install an aftermarket HID headlamp, your vehicle's audio and electronic device may malfunction.
B870D02MC-AAT
MICRO ANTENNA
OMC025111-1
Your car uses the micro antenna to re- ceive AM, FM and Satellite Radio broad- cast signals. This antenna is removable.
B850A02L
Fingerprints, dust, or soil on the surface of a disc could cause the pickup to skip signal tracks. Wipe the surface clean with a clean soft cloth. If the surface is heavily soiled, dampen a clean soft cloth in a solution of mild neu- tral detergent to wipe it clean.
CAUTION:
Before entering a place with a low height clearance or a car wash, remove the antenna by rotating it counterclockwise. If not, the antenna may be damaged.
PA710A01MC-AAT
RADIO, SET UP, VOLUME CONTROL (PA710) (If Installed)
DRIVING YOUR HYUNDAI 1
1231231. AM Selection Button 2. FM Selection Button 3. Automatic Channel Selection Button 4. Power ON/OFF & Volume Control
Button
5. SCAN Button 6. MUTE Button 7. SETUP Button 8. TUNE/ENTER Button 9. PRESET Button
A-200MCUA
1FEATURES OF YOUR HYUNDAI 124
PA710B01MC-AAT
1. AM Selection Button Pressing the [AM] button selects the AM band. AM Mode is displayed on the LCD.
2. FM Selection Button Turns to FM mode and toggles FM1 and FM2 when the button is pressed each time.
3. Automatic Channel Selection
Button
o When the [SEEK
] button is pressed, it reduces the band frequency by 200khz to automatically select chan- nel. Stops at the previous frequency if no channel is found.
o When the [SEEK
] button is pressed, it increases the band frequency by 50khz to automatically select channel. Stops at the previous frequency if no channel is found.
4. Power ON/OFF & Volume Control
Button
Turns on/off the set when the IGNITION SWITCH is on ACC or ON. If the button is turned to the right, it increases the volume and left, decreases the volume.
5. SCAN Button If this button is pressed, the frequencies will become increased and receive the corresponding broadcasts. This function will play the frequencies for 10 seconds each and find other broad- casts as the frequency increases. Press the button again when desiring to continue listening to the currently playing broadcast.
6. MUTE Button Press to temporarily cut off the Sound.
7. SETUP Button Press this button to turn to the SCROLL and P.BASS adjustment mode. If no action is taken for 5 seconds after pressing the button, it will return to the play mode.(After entering SETUP mode, move between items using the left, right and PUSH functions of the TUNE button.) The setup Items changes from SCROLL <->P.BASS.
8. TUNE/ENTER Button Turn this button clockwise one notch to increase frequency from current fre- quency. Turn this button counterclockwise by one notch to decrease frequency from current frequency. The frequency cahnges by 0.2Mhz in FM MODE and 9Khz in AM MODE. Press this button while holding SETUP button to activate / inactivate the item to. Select SETUP item using left and right function of the Tune button.
9. PRESET Button Push [1]~[6] buttons less than 0.8 second to play the channel saved in each button. Push PRESET button for 0.8 second or longer to save current channel to the respective button with a beep.
CAUTION:
o Do not place beverages close to the audio system. The audio system mechanism may be damaged if you spill them.
o Do not strike or allow anything to impact the audio system, damage to the system mechanisms could oc- cur.
PA710C01MC-AAT
CD (PA710) (If Installed)
DRIVING YOUR HYUNDAI 1
1251251. CD Loading Slot 2. CD Indicator 3. CD Eject Button 4. CD Selection Button 5. AUX Selection Button 6. Automatic Track Selection Button 7. Information Display Button 8. TUNE/ENTER Button 9. RANDOM Play Button 10. REPEAT Button 11. SCAN Play Button 12. FOLDER Button
A-200MCUA
1FEATURES OF YOUR HYUNDAI 126
1. CD Loading Slot Please face printed side upward and gently push in. When the ignition switch is on ACC or ON and power is off, power is automatically turned on if the CD is loaded. This CDP supports only 12cm CD. If VCD, Data CD, are loaded, "Er-6" message will appear and CD will be ejected.
2. CD Indicator When car ignition switch is ACC or ON and if the CD is loaded, this indicator is lighted. If the CD is ejected the light is turned off.
3. CD Eject Button Push button to eject the CD. This button is enabled when ignition switch is off.
4. CD Selection Button If there is a CD in the CDP DECK it plays the CD. Press CD button to automatically insert CD when the disc is ejected from the deck by pressing CD EJECT.
5. AUX Selection Button If the auxiliary device is connected, it turns to AUX MODE to play the sound from the auxiliary player. If no Disk and auxiliary device is con- nected, it displays “NO Media” 3 seconds and returns ti the previous mode.
8. TUNE/ENTER Button Turn this button clockwise to display songs after current song. Also, turn this button counterclockwise to display songs before current song. To listen to the displayed song, press the button to skip to the song and play.
9. RANDOM Play Button Turns on/off the randomization of the play list of files in the currently played DISC. To cancel the mode, press the key once again.
10. REPEAT Button Repeats current song when the button is pressed for less than 0.8 second. Repeats current folder when the button is pressed for 0.8 second or longer. (If there is no folder, entire disc will be repeated.)
6. Automatic Track Selection Button o Push [SEEK ] button for less than 0.8
second to play from the beginning of current song.o Push [SEEK ] button for less than 0.8
second and press again within 1 sec- onds to play the previous song.o Push [SEEK ] button for 0.8 or longer to initiate reverse direction high speed sound search of current song.
o Push [SEEK
] button for less than 0.8
second to play the next song.
o Push [SEEK
] button for 0.8 or longer to initiate high speed sound search of current song.
7. Information Display Button Displays the information of the current CD TRACK in the order of DISC TITLE ➟DISC ARTIST➟TRACK TITLE➟ TRACK ARTIST➟TOTAL TRACK➟Play Screen ➟DISC TITLE➟···.(not displayed if the in- formation is not available on the DISC.)
11. SCAN Play Button Plays first 10 seconds of each song in the DISC. To cancel the mode, press the key once again.
12. FOLDER Button Folder up/down operation. o Folder is moved up or down from cur- rently playing and folder name be- comes displayed.
o Press enter key
to play
the
selectedfolder.
o If the enter key is not pressed with in 5
seconds, then the previous folder name will be displayed again.DRIVING YOUR HYUNDAI 1
127127NOTE: o To assure Proper operation of the unit, keep the vehicle interior tem- perature within a nomal range by using the vehicle’s air conditioning or heating system.
o When replacing the fuse, replace it with a fuse having the correct capac- ity.
o All stored bookmarks are all erased when the car battery is disconnected or power to the vehocle is lost. if this occurs, the bookmarks will have to be reset.
o This equipment is designed to be used only in a 12 volt DC battery system with negative ground.
o This unit is made of precision parts. Do not attempt to disassemble or adjust any parts.
o when driving your vehicle, be sure to keep the volume of the unit set low enough to allow you to hear sounds coming from the outside.
o Do not expose this equipment (in- cluding the speakers and CD) to water or excessive moisture.
CAUTION:
o Do not insert warped or poor quality discs into the CD player as damage to the unit may occur.
o Do not insert anything like coins into the player slot as damage to the unit may occur.
o Do not place beverages close to the audio system. The playback mecha- nism may be damaged if you spill them.
o Do not strike or allow anything to impact the audio system, damage to the system mechanisms could oc- cur.
o Off-road or rough sunface driving may cause the compact disc to skip. Do not use the compact disc when driving in such conditions as dam- age to the compact disc face could occur.
o Do not attempt to grab or pull the compact disc out while the disc is being pulled into the audio unit by the self-loading mechanism. Damage to the audio unit and compact disc could occur.
1FEATURES OF YOUR HYUNDAI 128
PA710SA01MC-AAT
AUX/USB (PA710) (If Installed)
1. AUX/USB Selection Button 2. TRACK Moving Button 3. Random Playback Button 4. Repeat Selection Button 5. SCAN Selection Button 6. INFO Button 7. FOLDER Moving Button 8. SEARCH Knob & ENTER Button
A-200MCUA
PA710SB01MC-AAT
1. AUX/USB Selection Button If the auxiliary device is connected, it turns to AUX or USB mode to play the sound from the auxiliary player. If there is no auxiliary device, then it displays the message "No Media" for 3 seconds and returns to the previous mode.
2. TRACK Moving Button o Press the [TRACK ] button for less than 0.8 second to play from the begin- ning of the song currently played. Press the button for less than 0.8 sec- ond and press it again within 1 sec- onds to move to and play the previous track. Press the button for 0.8 second or longer to play the song in reverse direction in fast speed.
o Press the [TRACK ] button for less than 0.8 second to move to the next track. Press the button for 0.8 second or longer to play the song in forward direction in fast speed.
3. RANDOM Playback Button Press the button for less than 0.8 second to start or stop the random playback of the songs in the current folder. Press the button for more than 0.8 second to randomly play the entire songs in the USB device. Press the button again to cancel the mode.
4. REPEAT Selection Button Press the button for less than 0.8 second to repeat the song currently played. Press the button for more than 0.8 second to repeat the entire songs in the USB device.
5. SCAN Selection Button Scans each song in the USB device for 10 seconds each. Press the button once again to cancel scanning.
6. INFO Button Displays the information of the file cur- rently played in the order of FILE NAME ➟ TITLE ➟ ARTIST ➟ ALBUM ➟ FOLDER ➟ TOTAL FILE ➟ NORMAL DISPLAY ➟ FILE NAME ➟… (Displays no informa- tion if the file has no song information.)
DRIVING YOUR HYUNDAI 1
1291297. FOLDER Moving Button o Press [FOLDER ] button to move to child folder of the current folder and display the first song in the folder. Press TUNE/ ENTER knob to move to the folder displayed. It will play the first song in the folder.
o Press [FOLDER ] button to move to parent folder display the first song in the folder. Press TUNE/ENTER knob to move to the folder displayed.
8. SEARCH Knob & ENTER Button Turn this button clockwise to display the songs ahead of the currently played song. Turn the button counterclockwise to dis- play the songs before the currently played song. o Press the button to skip to and play the
selected song.
o Pressing the button changes the BASS, MIDDLE, TREBLE, FADER and BAL- ANCE TUNE mode. The mode selected is shown on the display. After selecting each mode, rotate the Audio control knob clockwise or counterclockwise.
1FEATURES OF YOUR HYUNDAI 130
CAUTION:
o To use an external USB device, make sure the device is not mounted when starting up the vehicle and mount the device after starting up.
o If you start the vehicle when the USB device is mounted, it may damage the USB device. (USB is not ESA)
o If the vehicle is started up or turned off while the external USB device is connected, the external USB device may not work.
o It may not play inauthentic MP3 or
WMA files. 1) It can only play MP3 files with the compression rate between 8Kbps~320Kbps. 2) It can only play WMA music files with the compression rate be tween 8Kbps~320Kbps.
o Take cautions for static electricity when mounting or dismounting the external USB device.
o An encoded MP3 player is not recog-
nizable.
o If you dismount the external USB device during playback in USB mode, the external USB device can be dam- aged or malfunction. Therefore, mount the external USB device when the engine is turned off or in another mode.
o Depending on the type and capacity of the external USB device or the type of the files stored in the device, there is a difference in the time taken for recognition of the device, but this is not an indicator of trouble and you only have to wait.
o Do not use the USB device for other purposes than playing music files. o Use of USB accessories such as recharger or heater using USB I/F may lower performance or cause trouble.
o If you use devices such as a USB hub you purchased separately, the vehicle’s audio system may not rec- ognize the USB device. Connect the USB device directly to the multime- dia terminal of the vehicle.
o If the USB device is divided by logi- cal drives, only the music files on the highest-priority drive are recognized by the car audio.
o Devices such as MP3 Player/ Cellu- lar phone/Digital camera and those that are not recognizable by stan- dard USB I/F can be unrecognizable. o USB devices other than standard-
ized goods (METAL COVER TYPE USB) can be unrecognizable.
o USB flash memory reader (such as CF, SD, microSD, etc.) or external- HDD type devices may be unrecog- nized.
o Music files protected by DRM (DIGI- TAL RIGHTS MANAGEMENT) are not recognizable.
o The data in the USB memory may be lost while using this AUDIO. It is recommeded to back up important data on a personal storage device. o Please avoid using USB memory products which can be used as key chains or cellular phone accesso- ries as they could cause damage to the USB jack. Please make certain only to use plug type connector prod- ucts as shown below.
PA710SC01MC-AAT
RUNNING iPod®(PA710) (If Installed)
DRIVING YOUR HYUNDAI 1
1311311. iPod Selection Button 2. TRACK Moving Button 3. RANDOM Playback Button 4. REPEAT Selection Button 5. INFO Button 6. SEARCH Knob & ENTER Button 7. CATEGORY Selection Button
A-200MCUA
iPod® is a trademark of Apple Inc.
1FEATURES OF YOUR HYUNDAI 132
PA710SD01MC-AAT
1. iPod Selection Button If an iPod is connected, the system switches to the iPod mode from the pre- vious mode to play the song files stored in the iPod. If there is no iPod connected, then the system displays the message "No Media" for 3 seconds and returns to the previous mode.
2. TRACK Moving Button o Press the [TRACK ] button for less than 0.8 second to play from the be- ginning of the song currently played. Press the button for less than 0.8
second and press it again within 1
seconds to move to and play the pre- vious track. Press the button for 0.8 second or longer to play the song in reverse direction in fast speed.o Press the [TRACK ] button for less than 0.8 second to move to the next track. Press the button for 0.8 second or longer to play the song in forward direction in fast speed.
3. RANDOM Playback Button Press the button for less than 0.8 second to start or stop the random playback of the songs within the current category. Press the button for longer than 0.8 sec- ond to randomly play all songs in the entire album of the iPod. Press the button once again to cancel the mode.
4. REPEAT Button Repeats the song currently played.
5. INFO Button Displays the information of the file cur- rently played in the order of TITLE ➟ ARTIST ➟ ALBUM ➟ NORMAL DISPLAY ➟ TITLE ➟... (Displays no information if the file has no song information.)
6. SEARCH Knob & ENTER Button When you turn the button clockwise, it will display the songs (category) ahead of the song currently played (category in the same level). Also, when you turn the button counter- clockwise, it will display the songs (cat- egory) before the song currently played (category in the same level). To listen to the song displayed in the song category, press the button to skip to and play the selected song. Pressing the button changes the BASS, MIDDLE, TREBLE, FADER and BAL- ANCE TUNE mode. The mode selected is shown on the display. After selecting each mode, rotate the Audio control knob clockwise or counterclockwise.
7. CATEGORY Selection Button Moves to the upper category from cur- rently played category of the iPod. To move to (play) the category (song) displayed, press TUNE/ENTER knob. You will be able to search through the lower category of the selected category. The order of iPod’s category is SONG, ALBUMS, ARTISTS, GENRES, and iPod.
NOTE: o Some iPod models might not support the communication protocol and the files will not be played. (iPod models supported: Mini, 4G, Photo, Nano, 5G)
o The order of search or playback of songs in the iPod can be different from the order searched in the audio system.
o If the iPod crashes due to its own trouble, reset the iPod. (Reset: Refer to iPod manual)
o An iPod may not operate normally on
low battery.
o Some iPod devices, such as the iPhone, can be connected through the Bluetooth interface. The device must have audio Bluetooth capabil- ity (such as for stereo headphone Bluetooth). The device can play, but it will not be controlled by the audio system.
DRIVING YOUR HYUNDAI 1
133133CAUTION:
o You need the power cable exclusive for an iPod in order to operate the iPod with the buttons on the audio system. The PC cable provided by Apple may cause a malfunction and should not be used in the vehicle.
o When connecting the device with the
iPod cable, push in the jack fully.
o When adjusting the sound effects of the iPod and the audio system, the sound effects of both devices may overlap and distort the quality of the sound.
o Deactivate (turn off) the equalizer function of the iPod when adjusting the audio system's volume, and turn off the equalizer of the audio system when using the equalizer of the iPod. o When the iPod cable is connected, the system can be switched to the AUX mode even without the iPod device and may cause noise. Dis- connect the iPod cable when not using the iPod device.
o When the iPod is not used with the audio system, the iPod cable should be removed from the iPod.
