2011 Hyundai Accent Owners Manual

oughly with clean water.

o The engine in your vehicle has alumi- num engine parts and must be pro- tected by an ethylene-glycol base coolant to prevent corrosion and freezing. Do not use hard water. Hard water can cause engine damage from cor- rosion, overheating or freezing.

DO-IT-YOURSELF MAINTENANCE

CHANGING THE AIR CLEANER FILTER

G070A03Y-AAT

OMC055010
The replacement of air cleaner filter is performed in the following manner. 1. Unsnap the clips around the cover. 2. When this is done, the cover can be lifted off, the old filter removed and the new filter put in its place.

Genuine Hyundai replacement parts are recommended.

CAUTION:

o Operating your vehicle without a proper air filter in place can result in excessive engine wear.

o When removing the air cleaner filter, be careful that dust or dirt does not enter the air intake. These may re- sult in damage to the air cleaner filter.

6 DO-IT-YOURSELF MAINTENANCE 10 WINDSHIELD WIPER

BLADES

G080A02A-AAT The wiper blades should be carefully inspected from time to time and cleaned to remove accumulations of road film or other debris. To clean the wiper blades and arms, use a clean sponge or cloth with a mild soap or detergent and water. If the wipers continue to streak or smear the glass, replace them with genuine Hyundai replacement parts or their equivalent.

G080B01HR-GAT

Replacing the Wiper Blades To replace the wiper blades, raise the wiper to the vertical.

To remove the wiper blade

CAUTION:

o Do not operate the wipers on dry glass. This can result in more rapid wear of the wiper blades and may scratch the glass.

o Keep the blade rubber out of contact with petroleum products such as engine oil, gasoline, etc.

2. Raise the wiper blade lightly and pull

up it.

HHR5049

(1)

HHR5048
1. Push down the wiper blade with the locking clip (1) pressed to detach it from the wiper arm.

To install the wiper blade

DO-IT-YOURSELF MAINTENANCE

FILLING THE WASHER RES- ERVOIR

G090A01MC-AAT

11

HHR5050

1. Put a new wiper blade onto the wiper arm and lower the wiper blade at the level of the wiper arm as shown in the drawing.

HHR5051

2. Pull up the wiper blade until you hear an audible "click" to engage in the end of the wiper arm.

NOTE: Do not allow the wiper arm to fall against the windshield.

OMC055016
A good quality washer fluid should be used to fill the washer reservoir. The fluid level should be checked more frequently during inclement weather or whenever the washer system is in more frequent use.

6 DO-IT-YOURSELF MAINTENANCE 12

CAUTION:

o Radiator anti-freeze (engine coolant) should not be used in the washer system because it will damage the car's finish.

o The washer should not be operated if the washer reservoir is empty. This can damage the washer fluid pump.

WARNING:

o Windshield washer fluid agents con- tain some amounts of alcohol and can be flammable under certain cir- cumstances. Do not allow sparks or flame to contact the washer fluid or the washer fluid reservoir. Damage to the vehicle or its occupants could occur.

o Windshield washer fluid is poison- ous to humans and animals. Do not drink windshield washer fluid. Seri- ous injury or death could occur.

CHECKING THE TRANSAXLE OIL (MANUAL)

CHECKING THE TRANSAXLE FLUID (AUTOMATIC)

G100A01MC-GAT Transaxle lubricant in the manual transaxle should be checked at those intervals specified in the vehicle mainte- nance schedule in Section 5.

G110A01MC-AAT Transaxle fluid in the automatic transaxle should be checked at those intervals specified in the vehicle maintenance schedule in Section 5.

WARNING:

It is always better to check the transaxle oil level when the engine is cool or cold. If the engine is hot, you should exercise great caution to avoid burning yourself on hot engine or exhaust parts.

NOTE: It is recommended that the manual transaxle fluid should be checked by an authorized Hyundai dealer.

NOTE: Automatic transaxle fluid is basically a red color. As driving distance increases, the fluid color turns darkish red gradu- ally. It is a normal condition and you should not judge the need to replace based upon the changing color. You must replace the automatic transaxle fluid in accordance with inter- vals specified in the vehicle mainte- nance schedule in section 5.

!

CAUTION:

Use of aftermarket ATF additives may cause damage to the automatic transaxle. Only use HYUNDAI GENUINE ATF SP III, DIAMOND ATF SP III, SK ATF SP III or other brands meeting the SP III specifi- cation approved by Hyundai Motor Co.. If you are having your vehicle serviced at a facility other than a Hyundai dealer, verify that the correct ATF is used for your vehicle.

WARNING:

The transaxle fluid level should be checked when the engine is at normal operating temperature. This means that the engine, radiator, exhaust system etc., are very hot. Exercise great care not to burn yourself during this proce- dure.

DO-IT-YOURSELF MAINTENANCE

13

G110D03A-AAT

Checking the automatic transaxle fluid level

Fluid level should be within "HOT" range

G110D03MC 3. Confirm if the fluid level is in the "HOT" range on the level gauge. If the fluid level is lower, add the specified fluid from the fill hole. If the fluid level is higher, drain the fluid from the drain hole.

4. If the fluid level is checked in cold condition [(fluid temperature 68~86°F (20~30°C)], add the fluid to the "COLD" line and then recheck the fluid level according to the above step 2.

OMC059006
The automatic transaxle fluid level should be checked regularly. Keep the vehicle on level ground with the parking brake applied and check the fluid level according to the following proce- dure.

1. Place the shift lever in N (Neutral) position and confirm the engine is run- ning at idle speed.

2. After the transaxle is warmed up suffi- ciently [(fluid temperature 158~176°F (70~80°C)], for example by 10 min- utes usual driving, move the shift lever through all positions then place the shift lever in N (Neutral) or P (Park) position.

6 DO-IT-YOURSELF MAINTENANCE 14

CHECKING THE BRAKES

G120A01A-AAT

WARNING:

The cooling fan is controlled by the engine coolant temperature and may sometimes operate even when the en- gine is not running. Use extreme cau- tion when working near the blades of the cooling fan, so that you are not injured by a rotating fan blade. As the engine coolant temperature decreases, the fan will automatically shut off. This is a normal condition.

CAUTION:

Because brakes are essential to the safe operation of the car, it is sug- gested that they be checked and in- spected by your Hyundai dealer. The brakes should be checked and in- spected for wear at those intervals specified in the vehicle maintenance schedule in Section 5.

G120B01A-AAT

Checking the Brake Fluid Level

WARNING:

Use caution when handling brake fluid. It can damage your vision if it gets into your eyes. It will also damage your vehicle's paint if spilled on it and not removed immediately.

G120D01A-AAT

To Check the Fluid Level

OMC055015
The fluid level in the brake fluid reservoir should be checked periodically. The level should be between the "MIN" and "MAX" marks on the side of the reservoir. If the level is at or below the "MIN" mark, care- fully add fluid to bring it up to "MAX". Do not overfill.

AIR CONDITIONER CARE

G140A01A-AAT

Keeping the Condenser Clean The air conditioner condenser (and en- gine radiator) should be checked periodi- cally for accumulation of dirt, dead in- sects, leaves, etc. These can interfere with maximum cooling efficiency. When removing such accumulations, brush or hose them away carefully to avoid bend- ing the cooling fans.

DO-IT-YOURSELF MAINTENANCE

15

Checking the amount of air condi- tioner refrigerant and compressor lubricant When the amount of refrigerant is low, the performance of the air conditioning is reduced. Overfilling also has a negative impact on the air conditioning system. Therefore, if abnormal operation is found, have the system inspected by an autho- rized HYUNDAI dealer.

NOTE: It is important when servicing the air conditioning system that the correct type and amount of oil and refrigerant is used. Otherwise, damage to the com- pressor and abnormal system opera- tion may occur.

G120E02A-AAT

Adding Brake Fluid

WARNING:

Handle brake fluid carefully. It can dam- age your vision if it gets into your eyes. Use only DOT 3 or DOT 4 specification fluid from a sealed container. Do not allow the fluid can or reservoir to re- main open any longer than required. This will avoid entry of dirt and moisture which can damage the brake system and cause improper operation.

To add brake fluid, first wipe away any dirt, then unscrew the fluid reservoir cap. Slowly pour the recommended fluid into the reservoir. Do not overfill. Carefully replace the cap on the reservoir and tighten.

6 DO-IT-YOURSELF MAINTENANCE 16

WARNING:

The air conditioning system should be serviced by an authorized HYUNDAI dealer. Improper service may cause serious injury to the person performing the service.

CHANGING THE CLIMATE CONTROL AIR FILTER

B145A02MC-GAT

(For Evaporator and Blower Unit) The climate control air filter is located in front of the evaporator unit behind the glove box. It helps to decrease the amount of pollut- ants entering the car.

B145A01MC 1. Open the glove box and remove the adjusting pins on both sides of the glove box.

OMC055012
2. Pull out the climate control air filter with

the hooks on both sides pressed.

CAUTION:

Be careful not to press the hooks in the opposite direction.

CHECKING AND REPLAC- ING FUSES

G200A01A-AAT

Replacing a Fusible Link

DO-IT-YOURSELF MAINTENANCE

17

CAUTION:

When replacing a fusible link, never use anything but a new fusible link with the same or lower amperage rating. Never use a piece of wire or a higher- rated fusible link. This could result in serious damage and create a fire haz- ard.

OMC055013
3. Take out the climate control air filter

and replace it with a new one.

4. Installation is the reverse order of dis-

assembly.

OMC045003
A fusible link will melt if the electrical circuits from the battery are ever over- loaded, thus preventing damage to the entire wiring harness. (This could be caused by a short in the system drawing too much current.) If this ever happens, have a Hyundai dealer determine the cause, repair the system and replace the fusible link. The fusible links are located in a relay box for easy inspection.

1. Turn off the ignition and all other

switches.

2. Open the fuse box and examine each fuse. Remove each fuse by pulling it toward you (a small "fuse puller" tool is contained in the relay and fuse box of the engine room to simplify this opera- tion).

3. Be sure to check all other fuses, even if you find one that appears to have opened.

6 DO-IT-YOURSELF MAINTENANCE 18

G200B02HP-AAT

Replacing Accessory Fuses

OMC045001
The fuse box for the lights and other electrical accessories will be found low on the dashboard on the driver's side. Inside the box you will find a list showing the circuits protected by each fuse. If any of your car's lights or other electrical accessories stop working, a blown (open) fuse could be the reason. If the fuse has opened, you will see that the metal strip inside the fuse has melted through. If you suspect a blown fuse, follow this proce- dure:

G200B02MC 4. Replace the blown fuse by pressing a new fuse of the same rating into place. The fuse should be a snug fit. If it is not, have the fuse clip repaired or replaced by a Hyundai dealer. If you do not have a spare fuse, you may be able to borrow a fuse of the same or lower rating from an accessory you can tem- porarily get along without (the radio or cigarette lighter, for example). Always remember to replace the borrowed fuse.

DO-IT-YOURSELF MAINTENANCE

19

NOTE: o If the power connector is pulled up from the fuse panel, the warning chime, audio, clock and interior lamps, etc., will not operate. The fol- lowing items must be reset after re- placement. - Digital Clock - Trip computer - Automatic heating and cooling con-

trol system

- Audio

o Even when the power connector is pulled up, the battery can still be discharged by operation of the head- lights or other electrical devices.

G200C01CM-GAT

Power Connector

G200F01MC

Your vehicle is equipped with a power connector to prevent battery discharge if your vehicle is parked without being op- erated for prolonged periods. Use the following procedures before parking the vehicle for prolonged periods.

1. Turn off the engine. 2. Turn off the headlights and tail lights. 3. Open the driver’s side panel cover and

pull up the power connector.

4. Insert the power connector in the op-

posite direction.

Good

Open-Replace

G200B02L

CAUTION:

An open fuse indicates that there is a problem in the electrical circuit. If you replace a fuse and it blows as soon as the accessory is turned on, the prob- lem is serious and should be referred to a Hyundai dealer for diagnosis and re- pair. Never replace a fuse with anything except a fuse with the same or a lower amperage rating. A higher capacity fuse could cause damage and create a fire hazard.

NOTE: See page 6-30 for the fuse panel de- scriptions.

6 DO-IT-YOURSELF MAINTENANCE 20

CHECKING THE BATTERY

G210A01A-AAT

OMC055018

WARNING:

Batteries can be dangerous! When working with batteries, carefully ob- serve the following precautions to avoid serious injuries.

The fluid in the battery contains a strong solution of sulfuric acid, which is poison- ous and highly corrosive. Be careful not to spill it on yourself or the car. If you do spill battery fluid on yourself, immediately do the following:

o If battery fluid is on your skin, flush the affected areas with water for at least 15
minutes and then seek medical assis- tance.

o If battery fluid is in your eyes, rinse out your eyes with water and get medical assistance as soon as possible. While you are being driven to get medical assistance, continue to rinse your eyes by using a sponge or soft cloth saturat- ed with water.

o If you swallow battery fluid, drink a large quantity of water or milk followed by milk of magnesia, eat a raw egg or drink vegetable oil. Get medical assis- tance as soon as possible.

While batteries are being charged (either by a battery charger or by the vehicle's alternator), they produce explosive gases. Always observe these warnings to pre- vent injuries from occurring: o Charge batteries only in a well venti-

o Do not permit flames, sparks or smok-

lated area.

ing in the area.

o Keep children away from the area.

G210B05A-AAT

Checking the Battery Keep the battery clean. Any evidence of corrosion around the battery posts or ter- minals should be removed using a solu- tion of household baking soda and warm water. After the battery terminals are dry, cover them with a light coating of grease.

CALIFORNIA PROPOSITION 65
WARNING:

Battery posts, terminals, and related accessories contain lead and lead com- pounds, chemicals known to the State of California to cause cancer, birth de- fects and reproductive harm. Batteries also contain other chemicals known to the State of California to cause cancer. Wash hands after handling.

!

WARNING: Always read the following in- structions carefully when han- dling a battery. Keep lighted cigarettes and all other flames or sparks away from the battery. Hydrogen, which is a highly combustible gas, is always present in battery cells and may explode if ignited. Keep batteries out of the reach of children because batteries contain highly corrosive SUL- FURIC ACID. Do not allow bat- tery acid to contact your skin, eyes, clothing or paint finish. If any electrolyte gets into your eyes, flush your eyes with clean water for at least 15 minutes and get immedi- ate medical attention. If pos- sible, continue to apply water with a sponge or cloth until medical attention is received. If electrolyte gets on your skin, thoroughly wash the con- tacted area. If you feel a pain or a burning sensation, get medical atten- tion immediately.

WARNING: Wear eye protection when charging or working near a battery. Always provide ventilation when working in an enclosed space. An inappropriately disposed battery can be harmful to the environment and human health. Dispose the battery according to your local law(s) or regulation.

o When lifting a plastic-cased battery, excessive pressure on the case may cause battery acid to leak, resulting in personal injury. Lift with a battery carrier or with your hands on oppo- site corners.

o Never attempt to charge the battery when the battery cables are con- nected.

o The electrical ignition system works

with high voltage. Never touch these components with the engine running or the ignition switched on.

DO-IT-YOURSELF MAINTENANCE

CHECKING COOLING FANS

ELECTRIC

G220A01A-AAT

21

WARNING:

The radiator fan is controlled by engine coolant temperature and may some- times operate even when the engine is not running. Use extreme caution when working near the blades of the cooling fan, so that you are not injured by a rotating fan blade. As the coolant tem- perature decreases the fan will auto- matically shut off. This is a normal con- dition.

G220B01A-AAT

Checking Engine Cooling Fan The engine cooling fan should come on automatically if the engine coolant tem- perature is high.

G220C01A-AAT

Checking Condenser Cooling Fan The condenser cooling fan should come on automatically whenever the air condi- tioner is in operation.

FOR MORE INFORMATION ABOUT YOUR HYUNDAI

G250A01A-AAT If you desire additional information about maintaining and servicing your Hyundai, you may purchase a factory Shop Manual at your Hyundai dealer's parts depart- ment. This is the same manual used by dealership technicians and while it is highly technical it can be useful in obtain- ing a better understanding of your car and how it works.

6 DO-IT-YOURSELF MAINTENANCE 22

POWER STEERING FLUID LEVEL

G230A01MC-AAT

(If Installed)

OMC055014
The power steering fluid level should be checked regularly. To check the power steering fluid level, be sure the engine is "OFF", then check to make certain that the power steering fluid level is between the "MAX" and "MIN" level markings on the fluid reservoir.

NOTE: o Grinding noise from the power steer- ing pump may be heard immediately after the engine is started in ex- tremely cold conditions (below -4°F). If the noise stops during warm up, there is no abnormal function in the system. It is due to a power steering fluid characteristic in extremely cold conditions.

o Do not start the engine when the power steering oil reservoir is empty.

G240A01A-AAT

POWER STEERING HOSES It is suggested that you check the power steering hose connections for fluid leak- age at those intervals specified in the vehicle maintenance schedule in Section 5. The power steering hoses should be re- placed if there is severe surface cracking, pulling, scuffing or worn spots. Deteriora- tion of the hose could cause premature failure.

REPLACEMENT OF LIGHT BULBS

G260A01MC-AAT Before attempting to replace a light bulb, be sure the switch is turned to the "OFF" position. The next paragraph shows how to reach the light bulbs so they may be changed. Be sure to replace the burned-out bulb with one of the same number and watt- age rating. See page 6-29 for the wattage descrip- tions.

CAUTION:

o Keep the lamps out of contact with petroleum products, such as oil, gasoline, etc.

o If you don't have necessary tools, the correct bulbs and the expertise, consult your authorized Hyundai dealer.

G270A02MC-GAT

Headlight, Front Turn Signal Light and Front Fog Light Type A

Turn signal light

Headlight

Fog light

Type B

Headlight

Turn signal light

Fog light

OMC055021

OMC050021

DO-IT-YOURSELF MAINTENANCE

23

CAUTION:

o The headlight aiming should be checked by an authorized Hyundai dealer after replacing the headlight bulbs.

o After heavy, driving rain or washing, headlight and taillight lenses could appear frosty. This condition is caused by the temperature differ- ence between the lamp inside and outside. This is similar to the con- densation on your windows inside your vehicle during the rain and doesn’t indicate a problem with your vehicle. If the water leaks into the lamp bulb circuitry, have the vehicle checked by an authorized Hyundai dealer.

Headlight

tection.

1. Allow the bulb to cool. Wear eye pro-

2. Open the engine hood and disconnect

the negative (-) post of the battery.

3. Always grasp the bulb by its plastic

base, avoid touching the glass.

4. Disconnect the power cord from the

back of the headlight.

6 DO-IT-YOURSELF MAINTENANCE 24

OMC055022

G270A03O

5. Remove the socket cover. 6. Push the bulb spring to remove the

headlight bulb.

7. Remove the protective cap from the replacement bulb and install the new bulb by matching the plastic base with the headlight hole. Reattach the bulb spring and install the socket cover. Reconnect the power cord.

8. Use the protective cap and carton to

dispose of the old bulb.

9.Check for proper headlight aim.

WARNING:

o When removing/replacing halogen bulbs, always handle the metal body of the bulb, not the glass. Residual oil may cause the bulb to overheat and burst when lit.

o The halogen bulb contains gas under pressure and if impacted could shat- ter, resulting in flying fragments. Al- ways wear eye protection when ser- vicing the bulb. Protect the bulb against abrasions or scratches and against liquids when lighted. Turn the bulb on only when installed in a headlight. Replace the headlight if damaged or cracked. Keep the bulb out of the reach of children and dis- pose of the used bulb with care.

Front Turn Signal light

1. Open the engine hood and disconnect

the negative (-) post of the battery.

OMC055023

2. Disconnect the power cord from the

bulb.

3. Take out the bulb from the bulb holder

by turning it counterclockwise.

4. Install the new bulb.

Front Fog Light (If Installed)

NOTE: It is recommended that the front fog light bulb be replaced by an authorized Hyundai dealer.

G270D01MC-AAT

Rear Combination Light 1. Open the trunk lid (4 Door) or tail gate

(3 Door).

4 Door

2. Remove the cover on the inside of

luggage trim.

OMC055024

4 Door

4 Door

DO-IT-YOURSELF MAINTENANCE

25

OMC055025
3. Remove the nuts of the rear combina-

tion light with a spanner.

3 Door

OMC055026

OMC055026-1

4. Detach the rear combination lamp by pulling it out (4 Door) or remove the mounting screws of the rear combina- tion lamp with a phillips screwdriver (3
Door).

6 DO-IT-YOURSELF MAINTENANCE 26

G270C01MC-GAT

Luggage Compartment Light

4 Door

OMC055027

HTB284

5. To replace the rear combination light, take it out from the bulb holder by turning it counterclockwise.

3 Door

3. Replace with a new bulb.

OMC055028

(1) Tail Light (2) Turn Signal Light (3) Back-up Light (4) Stop/Tail Light

6. Install the new bulb.

OMC055028-1
1. Open the trunk lid (4 Door) or tail gate

(3 Door).

2. Carefully remove the cover with a flat-

head screwdriver.

G270E01A-GAT

Side Repeater Light (If Installed) Type A

G220200AEN

Side Repeater Light (If Installed) Type B

DO-IT-YOURSELF MAINTENANCE

27

G270G01MC-GAT

Map Light (If Installed)

OMC055029

G270E01MC 1. Push the cover toward the front of

vehicle and remove it.

2. Disconnect the power code. 3. Replace with a new bulb.

OMC029250

If the light bulb is not operating, have the vehicle checked by an authorized Hyundai dealer.

1. Remove the cover with a flat-head

screwdriver.

2. Replace with a new bulb.

6 DO-IT-YOURSELF MAINTENANCE 28

G275H01MC-GAT

Interior Light

High Mounted Stop Light (4 Door) (If Installed)

OMC055030

1JBA7031

1. Remove the cover with a flat-head

screwdriver.

2. Replace with a new bulb.

1. Open the trunk lid.

1LDA5046

2. Remove the socket from the housing by turning the socket counterclockwise until the tabs on the socket align with the slots on the housing.

3. Remove the bulb from the socket by pressing it in and rotating it until the tabs on the bulb align with the slots in the socket. Pull the bulb out of the socket.

4. Insert a new bulb by inserting it into the socket and rotating it until it locks into place.

5. Install the socket in the housing by aligning the tabs on the socket with the slots in the housing. Insert the socket into the housing and turn the socket clockwise.

High Mounted Stop Light (3 Door) (If Installed) If the light bulb is not operating, have the vehicle checked by an authorized Hyundai dealer.

BULB WATTAGE

G280A03MC-AAT

4 Door

3 Door

DO-IT-YOURSELF MAINTENANCE

29

No.

Part Name

Wattage

Bulb Type

No.

Part Name

Wattage

Bulb Type

Headlight (High/Low)

Front Turn Signal Light/

Side Marker Light

Map Light (If Installed)

Interior Light

Front Fog Light (If Installed)

Side Repeater Light (If Installed)

55/60

HB2 Long Life

28/8

2357

10

10

27

0.4

10W (FESTOON)

10W (FESTOON)

GE881

LED Type

10

11

12

13

Side Repeater Light (If Installed)

Stop/Tail Light

High Mounted Rear Stop Light

Luggage Compartment Light

Rear Turn Signal Light

Back-up Light

License Plate Light

27/8

16

27

16

WY5W

1157

W16W

C5W

1156

W16W

C5W

OMC059020L

6 DO-IT-YOURSELF MAINTENANCE 30

FUSE PANEL DESCRIPTION

G200C01MC-AAT

Engine Compartment

FUSE MAIN

BATT #1
BLOWER ABS #1
ABS #2
IGN #2
IGN #1
BATT #2
P/WDW

RAD ECU A ECU C

INJ

A/CON #1
A/CON #2

ECU B HORN

SNSR

COND

FUSE RATING

CIRCUIT PROTECTED

125A 50A 40A 40A 40A 40A 30A 30A 30A 30A 30A 20A

15A

10A 10A 10A 10A

10A

30A

Generator I/P Junction Box Blower Relay, Blower Motor ABS Control Module, Multipurpose Check Connector ABS Control Module, Multipurpose Check Connector Start Relay, Ignition Switch Ignition Switch I/P Junction Box, Tail Lamp Relay I/P Junction Box, Power Window Relay Radiator Fan Relay Main Relay, Fuel Pump Relay ECM, PCM Injector #1, #2, #3, #4, CVVT Oil Control Valve, Immobilizer Control Module,Purge Control Solenoid Valve, Idle Speed Control Actuator, Fuel Pump Relay A/Con Relay A/C Control Module ECM, PCM Horn Relay, Burglar Alarm Horn Relay A/Con Relay, Rad Fan Relay, Cond Fan Relay #1, #2, Camshaft Position Sensor,Oxygen Sensor(UP, DOWN), Mass Air Flow Sensor Condenser Fan Relay #1

G200C01MC

NOTE: Not all fuse panel descriptions in this manual may be applicable to your vehicle. It is accurate at the time of printing. When you inspect the fuse box on your vehicle, refer to the fuse box label.

G200E01MC-AAT

Inner Panel

DO-IT-YOURSELF MAINTENANCE

31

FUSE

FUSE RATING

CIRCUIT PROTECTED

P/WDW RH

P/WDW LH

AUDIO

C/LIGHTER H/LP (LH)

HTD MIRR

RR WIPER FR WIPER TAIL LP (LH)

IGN

HTD SEAT

BLOWER

TAIL LP (RH)

HTD GLASS

AMP

H/LP (RH) HAZARD A/BAG SNSR

25A

25A 10A 25A 10A

10A

15A 25A 10A 10A 20A

10A

10A

30A 25A 10A 10A 15A 10A

Driver Power Window Switch, Assist Power Window Switch,Rear Power Window Switch RH Driver Power Window Switch, Rear Power Window Switch LH Power Outside Mirror Switch, Digital Clock, Audio Cigarette Lighter, Power Outlet Head Lamp LH, DRL Control Module ECM, Driver Power Outside Mirror Motor,Assist Power Outside Mirror Motor, PCM, Rear Defogger Switch Multi-function Swicth, Rear Wiper Motor Multi-function Switch, Front Wiper Motor Rear Combination Lamp LH, License Lamp LH(3DOOR),Turn Signal Lamp LH Front Fog Relay Driver Seat Warmer Switch, Assist Seat Warmer Switch Active Interior & Humidity Sensor, A/C Control Module, BCM, Blower Relay, Sunroof Motor Rear Combination Lamp RH, License Lamp RH(3DOOR), License Lamp(4DOOR), Shunt Connector, Turn Signal Lamp RH BCM, Rear Defogger, Rear Defogger Relay AMP Head Lamp RH, Instrument Cluster, DRL Control Module Hazard Relay, Hazard Switch SRS Control Module Telltale Lamp, Passenger Seat Track Position Sensor

G200E01MC

6 DO-IT-YOURSELF MAINTENANCE 32

FUSE

FUSE RATING

CIRCUIT PROTECTED

FR FOG LP

S/ROOF T/SIG LP

TCU

STOP LP

A/BAG IND

ECU

C/DR LOCK

START

CLUSTER

IGN COIL

AUDIO

(Power Connector)

MULT B/UP

(Power Connector)

ABS

B/UP LP

DRL

10A

20A 10A 10A

15A

10A 10A

20A

10A

10A

15A

15A

10A

10A 10A 10A

Front Fog Lamp Switch, Front Fog Lamp LH, Front Fog Lamp RH, Front Fog Lamp Relay Sunroof Motor Hazard Switch Overdrive Switch, Vehicle Speed Sensor Data Link Connector, Stop Lamp Switch, P/WDW Relay,Multipurpose Check Connector Instrument Cluster ECM, PCM Driver Door Lock Actuator, Assist Door Lock Actuator, BCM,Rear Door Lock Actuator LH, Rear Door Lock Actuator RH,Driver Power Window Switch, Tail Gate Lock Actuator Start Relay, Burglar Alarm Relay BCM, Instrument Cluster, Generator, DRL Control Module, Tire Pressure Monitoring Module, Pre-excitation Resistor Ignition Coil #1, #2, #3, #4, Condenser

Audio

Luggage Lamp, Room Lamp, Vanity Lamp Switch, Digital Clock,Overhead Console Lamp, A/C Control Module, Instrument Cluster, Door Warning Switch, BCM, Tire Pressure Monitoring Module ABS Control Module, Multipurpose Check Connector Back-up Lamp Switch, Transaxle Range Switch, Multipurpose Check Connector DRL Control Module

EMISSION CONTROL SYSTEMS

Emission Control System ............................................. 7-2
Catalytic Converter ....................................................... 7-3

7 EMISSION CONTROL SYSTEMS

EMISSION CONTROL SYSTEM

H010A01A-AAT Your Hyundai is equipped with an emis- sion control system to meet all require- ments of the U.S. Environmental Protec- tion Agency or California Air Resources Board. There are three emission control systems which are as follows.

1) Crankcase Emission Control System 2) Evaporative Emission Control System 3) Exhaust Emission Control System

In order to ensure the proper function of the emission control systems, it is recom- mended that you have your car inspected and maintained by an authorized Hyundai dealer in accordance with the mainte- nance schedule in this manual.

Canister Fuel vapors generated inside the fuel tank are absorbed and stored in the onboard canister. When the engine is running, the fuel vapors absorbed in the canister are drawn into the induction sys- tem through the purge control solenoid valve.

Purge Control Solenoid Valve (PCSV) The purge control solenoid valve is con- trolled by the Engine Control Module (ECM); when the engine coolant tem- perature is low during idling, the PCSV closes so that evaporated fuel is not taken into the engine. After the engine warms- up during ordinary driving, the PCSV opens to introduce evaporated fuel to the engine.

H010B01A-AAT

1. Crankcase Emission Control

System

The positive crankcase ventilation sys- tem is employed to prevent air pollution caused by blow-by gases being emitted from the crankcase. This system supplies filtered fresh air to the crankcase through the air intake hose. Inside the crankcase, the fresh air mixes with blow-by gases, then passes through the PCV valve into the induction system.

H010C01S-AAT

2. Evaporative Emission Control (In- cluding ORVR: Onboard Refuel- ing Vapor Recovery) System

The Evaporative Emission Control Sys- tem is designed to prevent fuel vapors from escaping into the atmosphere. (The ORVR system is designed to allow the vapors from the fuel tank to be loaded into a canister while refueling at the gas station, preventing the escape of fuel vapors into the atmosphere.)

H010D02A-AAT

3. Exhaust Emission

Control System

The Exhaust Emission Control System is a highly effective system which controls exhaust emissions while maintaining good vehicle performace.

CALIFORNIA PROPOSITION 65
WARNING:

Engine exhaust and a wide variety of automobile components and parts, in- cluding components found in the inte- rior furnishings in a vehicle, contain or emit chemicals known to the State of California to cause cancer and birth defects and reproductive harm. In addi- tion, certain fluids contained in vehicles and certain products of component wear contain or emit chemicals known to the State of California to cause can- cer and birth defects or other repro- ductive harm.

CATALYTIC CONVERTER

H020A03A-AAT

(If Installed)

EMISSION CONTROL SYSTEMS

WARNING:

o Use unleaded fuel only. o Maintain the engine in good operat- ing condition. Extremely high cata- lytic converter temperatures can re- sult from improper operation of the electrical, ignition or multiport elec- tronic fuel injection.

o If your engine stalls, pings, knocks, or is hard to start, have your Hyundai dealer inspect and repair the prob- lem as soon as possible.

o Avoid driving with a very low fuel level. Running out of gasoline may cause the engine to misfire and re- sult in damage to the catalytic con- verter.

o Avoid idling the engine for periods

longer than 10 minutes.

o The vehicle should not be pushed or pulled to get started. This may cause the catalytic converter to overheat and create a fire hazard.

Catalytic Converter

H020A01MC Hyundai vehicle is equipped with a mono- lith type three-way catalytic converter to reduce the carbon monoxide, hydrocar- bons and nitrogen oxides contained in the exhaust gas. Exhaust gases passing through the catalytic converter cause it to operate at a very high temperature. The introduction of large amounts of unburned gasoline into the exhaust may cause the catalytic converter to overheat and create a fire hazard. This risk may be reduced by observing the following:

7 EMISSION CONTROL SYSTEMS

WARNING:

o Do not touch the catalytic converter or any other part of the exhaust sys- tem while the catalytic converter is hot. Shut off the engine, wait for at least one hour before touching the catalytic converter or any other part of the exhaust system.

o Remember that your Hyundai dealer is your best source of assistance. o Do not park, idle or drive your ve- hicle over any combustible material such as grass, paper, leaves or rags. These materials might contact the hot catalytic converter and a fire might result.

CONSUMER INFORMATION, REPORTING

SAFETY DEFECTS & BINDING

ARBITRATION OF WARRANTY CLAIMS

Vehicle Identification Number (VIN) ............................. 8-2
Engine Number ............................................................. 8-3
Tire Information ............................................................. 8-3
Recommended Cold Tire Inflation Pressures .............. 8-3
Checking Tire Inflation Pressure .................................. 8-6
Tire Sidewall Labeling ................................................... 8-6
Tire Terminology and Definitions .................................. 8-8
All Season Tires ......................................................... 8-10
Snow Tires.................................................................. 8-10
Tire Chains ................................................................. 8-11
Tire Rotation ............................................................... 8-11
Tire Balancing ............................................................. 8-12
Tire Traction................................................................ 8-12
When to Replace Tires ............................................... 8-12
Tire Maintenance ........................................................ 8-13
Spare Tire and Tools .................................................. 8-14
Warranties for Your Hyundai Vehicle ......................... 8-15
Consumer Information ................................................ 8-15
Reporting Safety Defects ........................................... 8-18
Binding Arbitration of Warranty Claims ...................... 8-18

8 CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS

VEHICLE IDENTIFICATION NUMBER (VIN)

I010A02MC-AAT

1JBA5003

1JBA5005

OMC079011

OMC079010

The vehicle identification number (VIN) is the number used in registering your car and in all legal matters pertaining to its ownership, etc. It can be found in four different places on your car:

1. The number is punched on floor under the front passenger seat. To check the number, remove the cover.

2. The VIN is also on a plate attached to the top of the dashboard. The number on the plate can easily be seen through the windshield from outside.

3. The vehicle certification label attached on the driver's side center pillar gives the vehicle identification number (VIN). 4. On the lower side of the center pillar

outer panel.

ENGINE NUMBER

I010B01A-AAT

OMC065001
The engine number is stamped on the engine block as shown in the drawing.

CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS TIRES

I030A02MC-AAT

RECOMMENDED COLD TIRE INFLA- TION PRESSURES

I020A02A-AAT

TIRE INFORMATION The tires supplied on your new Hyndai are chosen to provide the best perfor- mance for normal driving. If you ever have questions about your tire warranty and where to obtain ser- vice, see the tire manufacture's book- let included with your vehicle's Owner's Manual Literature Kit.

OMC079012
Tire label located on the driver's side of the center pillar outer panel gives the cold tire pressures recommended for your vehicle with the original tire size, the number of people that can be in your vehicle and vehicle capacity weight.

8 CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS

Type A

Type C

Type B

Type D

OMC040405

OMC040407

OMC040406

OMC040408

These pressures were chosen to pro- vide the most satisfactory combina- tion of ride comfort, tire wear and stability under normal conditions. Tire pressures should be checked at least monthly. Proper tire inflation pressures should be maintained for these rea- sons:

WARNING:

o Inspect your tires frequently for proper inflation as well as wear and damage. Always use a tire pressure gauge.

o Tires with too much or too little pressure wear unevenly causing poor handling, loss of vehicle control, and sudden tire failure leading to accidents, injuries, and even death. The recommended cold tire pressure for your ve- hicle can be found in this manual and on the tire label located on the driver's side of the center pillar.

!

WARNING:

o Worn tires can cause accidents. Replace tires that are worn, show uneven wear, or are damaged. See page 8-12.

o Remember to check the pressure of your spare tire. Hyundai rec- ommends that you check the spare every time you check the pressure of the other tires on your vehicle.

CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS

NOTE: o Underinflation also results in ex- cessive wear, poor handling and reduced fuel economy. Wheel de- formation also is possible. Keep your tire pressures at the proper levels. If a tire frequently needs refilling, have it checked by your Hyundai Dealer.

o Overinflation produces a harsh ride, excessive wear at the center of the tire tread, and a greater possibility of damage from road hazards.

WARNING:

Overinflation or underinflation can reduce the tire life, adversely affect vehicle handling, and lead to sud- den tire failure. This could rusult in loss of vehicle control and potential injury.

CAUTION:

Always observe the following:

o Check pressures when the tires are cold. (After the vehicle has been parked for at least three hours or hasn't been driven more than one mile (1.6 km) since start- ing up.)

o Check the pressure of your spare tire each time you check the pres- sure of other tires.

o Never overload your vehicle. Be especially careful about overload- ing if you equip your vehicle with a luggage rack.

o Worn, old tires can cause acci- dents. If your tread is badly worn, or if your tires have been dam- aged, replace them.

8 CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS

If you overfill the tire, release air by pushing on the metal stem in the center of the tire valve. Recheck the tire pressure with the tire gauge. Be sure to put the valve caps back on the valve stems. They help prevent leaks by keeping out dirt and moisture.

I030B01MC-AAT

TIRE SIDEWALL LABELING

5, 6

I030B04JM

Federal law requires tire manufactur- ers to place standardized information on the sidewall of all tires. This infor- mation identifies and describes the fundamental characteristics of the tire and also provides the tire identification number (TIN) for safety standard cer- tification. The TIN can be used to identify the tire in case of a recall.

I035A01JM-AAT

CHECKING TIRE INFLATION PRES- SURE Check your tires once a month or more. Also, check the tire pressure of the spare tire.

How to Check Use a good quality gauge to check tire pressure. You can not tell if your tires are properly inflated simply by looking at them. Radial tires may look properly inflated even when they're underinflated. Check the tire's inflation pressure when the tires are cold. - "Cold" means your vehicle has been sitting for at least three hours or driven no more than 1
mile (1.6 km). Remove the valve cap from the tire valve stem. Press the tire gauge firmly onto the valve to get a pressure mea- surement. If the cold tire inflation pres- sure matches the recommended pres- sure on the tire and loading information label, no further adjustment is neces- sary. If the pressure is low, add air until you reach the recommended amount.

CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS

1. Manufacturer or Brand name

o Manufacturer or Brand name is

shown.

2. Tire size (example: P175/70R14)

o The "P" indicates the tire is de- signed for passenger vehicles. A "T" is the designation for a tempo- rary spare tire.

o Three-digit number (175): This number gives the width in millime- ters of the tire from sidewall edge to sidewall edge.

o Two-digit number (70): This num- ber, known as the aspect ratio, gives the tire's ratio of height to width.

o R: The "R" stands for radial. o Two-digit number (14): This num- ber is the wheel or rim diameter in inches.

o Two (or three) digit number (84): This number is the tire's load in- dex. It is a measurement of how much weight each tire can sup- port.

o T: Speed Rating. The speed rat- ing denotes the speed at which a tire is designed to be driven for extended periods of time. The ratings range from "A" to "Z" (98
to 186 MPH).

3. TIN (Tire Identification Number) for new tire (example: DOT XX XX XXX XXXX) o DOT: Abbreviation for the "De- partment of Transportation". The symbol can be placed above, be- low or to the left or right of the Tire Identification Number. Indicates tire is in compliance with the U.S. Department of Transportation Motor Vehicle Safety Standards. o 1st two-digit code: Manufacturer's

identification mark

o 2nd two-digit code: Tire size o 3rd three-digit code: Tire type code

(Optional)

o 4th four-digit code: Date of Manu-

facture

o Four numbers represent the week and year the tire was built. For example, the numbers 3109
means the 31st week of 2009.

4. Tire ply composition and mate-

rial The number of layers or plies of rubbercoated fabric in the tire. Tire manufacturers also must indicate the materials in the tire, which in- clude steel, nylon, polyester, and others. The letter "R" means radial ply construction; the letter "D" means diagonal or bias ply construction; and the letter "B" means belted-bias ply construction.

5. Maximum permissible inflation

pressure This number is the greatest amount of air pressure that should be put in the tire. Do not exceed the maxi- mum permissible inflation pressure. Refer to the Tire and Loading Infor- mation label for recommended infla- tion pressure.

8 CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS

6. Maximum load rating

This number indicates the maxi- mum load in kilograms and pounds that can be carried by the tire. When replacing the tires on the vehicle, always use a tire that has the same load rating as the factory installed tire.

7. Uniform Tire Quality Grading

(UTQG): Tire manufacturers are required to grade tires based on three perfor- mance factors: treadwear, traction and temperature resistance. For more information, see Uniform Tire Quality Grading on page 8-15.

I030D01JM-AAT

TIRE TERMINOLOGY AND DEFINI- TIONS Air Pressure: The amount of air inside the tire pressing outward on the tire. Air pressure is expressed in pounds per square inch (psi) or kilopascal (kPa). Accessory Weight: This means the combined weight of optional accesso- ries. Some examples of optional ac- cessories are, automatic transmission, power seats, and air conditioning. Aspect Ratio: The relationship of a tire's height to its width. Belt: A rubber coated layer of cords that is located between the plies and the tread. Cords may be made from steel or other reinforcing materials. Bead: The tire bead contains steel wires wrapped by steel cords that hold the tire onto the rim. Bias Ply Tire: A pneumatic tire in which the plies are laid at alternate angles less than 90 degrees to the centerline of the tread.

Cold Tire Pressure: The amount of air pressure in a tire, measured in pounds per square inch (psi) or kilopascals (kPa) before a tire has built up heat from driving. Curb Weight: This means the weight of a motor vehicle with standard and optional equipment including the maxi- mum capacity of fuel, oil and coolant, but without passengers and cargo. DOT Markings: A code molded into the sidewall of a tire signifying that the tire is in compliance with the U.S. Department of Transportation motor vehicle safety standards. The DOT code includes the Tire Identification Number (TIN), an alphanumeric desig- nator which can also identify the tire manufacturer, production plant, brand and date of production. GVWR: Gross Vehicle Weight Rating GAWR FRT: Gross Axle Weight Rat- ing for the front Axle. GAWR RR: Gross Axle Weight Rating for the rear axle.

CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS

Intended Outboard Sidewall: The side of an asymmetrical tire, that must always face outward when mounted on a vehicle. Kilopascal (kPa): The metric unit for air pressure. Load Index: An assigned number rang- ing from 1 to 279 that corresponds to the load carrying capacity of a tire. Maximum Inflation Pressure: The maximum air pressure to which a cold tire may be inflated. The maximum air pressure is molded onto the sidewall. Maximum Load Rating: The load rat- ing for a tire at the maximum permis- sible inflation pressure for that tire. Maximum Loaded Vehicle Weight: The sum of curb weight; accessory weight; vehicle capacity weight; and production options weight. Normal Occupant Weight: The num- ber of occupants a vehicle is designed to seat multiplied by 150 pounds (68
kg).

Occupant Distribution: Designated seating positions. Outward Facing Sidewall: The side of a asymmetrical tire that has a par- ticular side that faces outward when mounted on a vehicle. The side of the tire that contains a whitewall, bears white lettering or bears manufacturer, brand and or model name molding that is higher or deeper than the same moldings on the other sidewall of the tire. Passenger (P-Metric) Tire: A tire used on passenger cars and some light duty trucks and multipurpose vehicles. Recommended Inflation Pressure: Vehicle manufacturer's recommended tire inflation pressure and shown on the tire placard. Radial Ply tire: A pneumatic tire in which the ply cords that extend to the beads are laid at 90 degrees to the centerline of the tread.

Rim: A metal support for a tire and upon which the tire beads are seated. Sidewall: The portion of a tire be- tween the tread and the bead. Speed Rating: An alphanumeric code assigned to a tire indicating the maxi- mum speed at which a tire can oper- ate. Traction: The friction between the tire and the road surface. The amount of grip provided. Tread: The portion of a tire that comes into contact with the road. Treadwear Indicators: Narrow bands, sometimes called "wear bars," that show across the tread of a tire when only 2/32 inch of tread remains. UTQGS: Uniform Tire Quality Grading Standards, a tire information system that provides consumers with ratings for a tire's traction, temperature and treadwear. Ratings are determined by tire manufacturers using government testing procedures. The ratings are molded into the sidewall of the tire.

8 CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS 10

Vehicle Capacity Weight: The num- ber of designated seating positions multiplied by 150 lbs. (68 kg) plus the rated cargo and luggage load. Vehicle Maximum Load on the Tire: Load on an individual tire due to curb and accessory weight plus maximum occupant and cargo weight. Vehicle Normal Load on the Tire: That load on an individual tire that is determined by distributing to each axle its share of the curb weight, accessory weight, and normal occupant weight and dividing by 2. Vehicle Placard: A label permanently attached to a vehicle showing the origi- nal equipment tire size and recom- mended inflation pressure.

I040B01JM-AAT

ALL SEASON TIRES Hyundai specifies all season tires on some models to provide good perfor- mance for use all year round, including snowy and icy road conditions. All sea- son tires are identified by ALL SEA- SON and/or M+S (Mud and Snow) on the tire sidewall. Snow tires have better snow traction than all season tires an may be more appropriate in some areas.

I040A01O-AAT

SNOW TIRES If you equip your car with snow tires, they should be the same size and have the same load capacity as the original tires. Snow tires should be installed on all four wheels; otherwise, poor handling may result. Snow tires should carry 4 psi (28 kPa) more air pressure than the pressure recommended for the standard tires on the tire label on the driver's side of the center pillar , or up to the maximum pressure shown on the tire sidewall whichever is less. Do not drive faster than 75 mph (120
km/h) when your car is equipped with snow tires.

CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS

11

WARNING:

o If you have noise caused by chains contacting the body, re- tighten the chain to avoid contact with the vehicle body.

o To prevent body damage, re- tighten the chains after driving 0.3~0.6 miles.

o Don't use tire chains on a vehicle equipped with aluminium wheels. If it is unavoidable, use wire type chains.

o Use wire chains less than 15 mm to prevent damage to the chain's connection.

I060A02A-AAT

TIRE ROTATION