2004 Hyundai Accent Owners Manual

40%

50%

60%

Water

65%

60%

50%

40%

HLC5005
The coolant level can be seen on the side of the plastic coolant reservoir. The level of the coolant should be between the "L" and "F" lines on the reservoir when the engine is cool. If the level is below the "L" mark, add engine coolant to bring it up between "L" and "F". If the level is low, inspect for coolant leaks and recheck the fluid level frequently. If the level drops again, visit your Hyundai dealer for an inspection and diag- nosis of the reason.

G050D02A-AAT To Change the Coolant

The coolant should be changed at those inter- vals specified in the vehicle maintenance sched- ule in Section 5.

DO-IT-YOURSELF MAINTENANCE

CAUTION:

Engine coolant can damage the finish of your car. If you spill engine coolant on the car, wash it off thoroughly with clean water.

1. Park the car on level ground, set the parking brake and remove the radiator cap when cool.

2. Be sure your drain receptacle is in place. Open the drain cock on the radiator. Allow all the engine coolant to drain from the cooling system, then securely close the drain cock. 3. Check Section 9 for the capacity of the cooling system in your car. Then, following the manufacturer's directions on the engine coolant container, add the appropriate quan- tity of coolant to the radiator.

G050D01A

G050D02A

4. Turn the radiator cap counterclockwise with- out pressing down on it, until it stops. This relieves any pressure remaining in the cool- ing system. And remove the radiator cap by pushing down and turning counterclockwise. Now fill the radiator with clean demineralized or distilled water. Continue to add clean demineralized or distilled water in small quan- tities until the fluid level stays up in the radiator neck.

5. Start the engine, top off the radiator with water and then add engine coolant to the reservoir until the level is between "L" and "F".

6. Replace the radiator and reservoir caps and check to be sure the drain cocks are fully closed and not leaking.

6 DO-IT-YOURSELF MAINTENANCE

REPLACING THE SPARK PLUGS

G060B01A-AAT

WARNING:

The cooling fan is controlled by engine cool- ant temperature and may sometimes operate even when the engine is not running. Use extreme caution when working near the blades of the cooling fan so that you are not injured by a rotating fan blade. As the engine coolant temperature decreases, the fan will automatically shut off. This is a normal con- dition.

0.039 ~ 0.043 in. (1.0 ~ 1.1 mm )

G060A01L The spark plugs should be changed at the intervals specified in the vehicle maintenance schedule in section 5, or whenever engine per- formance indicates they should be changed. Symptoms that suggest poor spark plug perfor- mance include engine misfiring under load, loss of fuel economy, poor acceleration, etc. When spark plugs are replaced, always use spark plugs recommended by Hyundai. The use of other spark plugs can result in loss of perfor- mance, radio interference or engine damage.

NOTE: When replacing the spark plugs, genuine Hyundai replacement parts are recom- mended.

Recommended Spark Plugs: CHAMPION : RC10YC4
NGK : BKR5ES-11

G060C01S-GAT Changing the Spark Plugs

You will find it easier to change spark plugs if the engine is cold. Always change one spark plug at a time. This helps avoid getting the wires mixed up.

G060C01A-D 1. Remove the center cover on the engine

rocker cover.

2. Using a clean cloth, remove any dirt that has accumulated around the base of the spark plug so it cannot fall into the cylinder when the spark plug is removed.

3. To remove the spark plug cable, pull straight up on the insulated connector, not the cable. Pulling on the cable may damage the carbon core conductor.

5. To remove the old spark plug, turn the wrench

handle in a counterclockwise direction.

DO-IT-YOURSELF MAINTENANCE

WARNING:

It is recommended that the engine be cool or cold when changing the spark plugs. If the engine is hot, you could burn yourself on the insulated connector, the spark plug or the engine itself.

4. When preparing to remove the old spark plug, guide the socket down over the spark plug, being careful not to damage the ce- ramic insulator.

6. To install the new spark plug, guide the socket down over the spark plug, being care- ful not to damage the ceramic insulator.

G060C03A-D

G060C04A-D

NOTE: Spark plugs should be tightened firmly. Over- tightening can damage the threads in the aluminum cylinder head. Also, leaving them too loose can cause the spark plugs to get very hot and possibly result in damage to the engine.

7. Replace the cable by pushing the insulated connector directly down onto the electrode. Check to be sure it has snapped into place and can't fall off.

G060C02A-D

6 DO-IT-YOURSELF MAINTENANCE 10

CHANGING THE AIR CLEANER FILTER G070A03Y-AAT

CAUTION:

o Operating your vehicle without a proper air filter in place can result in excessive engine wear.

o When removing the air cleaner filter, be careful that dust or dirt does not enter the air intake. These may result in damage to the air cleaner filter.

G070A01A

The replacement of air cleaner filter is per- formed in the following manner.

1. Unsnap the clips around the cover. 2. When this is done, the cover can be lifted off, the old filter removed and the new filter put in its place.

Genuine Hyundai replacement parts are recom- mended.

WINDSHIELD WIPER BLADES

G080A02A-AAT

HEF119

The wiper blades should be carefully inspected from time to time and cleaned to remove accu- mulations of road film or other debris. To clean the wiper blades and arms, use a clean sponge or cloth with a mild soap or detergent and water. If the wipers continue to streak or smear the glass, replace them with genuine Hyundai re- placement parts or their equivalent.

CAUTION:

o Do not operate the wipers on dry glass. This can result in more rapid wear of the wiper blades and may scratch the glass. o Keep the blade rubber out of contact with petroleum products such as engine oil, gasoline, etc.

FILLING THE WASHER RESERVOIR

CHECKING THE TRANSAXLE OIL (MANUAL)

G090A01A-AAT

G100A03A-AAT

DO-IT-YOURSELF MAINTENANCE

11

WARNING:

It is always better to check the transaxle oil level when the engine is cool or cold. If the engine is hot, you should exercise great caution to avoid burning yourself on hot engine or exhaust parts.

HLC5007
A good quality washer fluid should be used to fill the washer reservoir. The fluid level should be checked more frequently during inclement weath- er or whenever the washer system is in more frequent use. The capacity of the washer reservoir is 3.2 U.S. quarts (3.0 Liters).

CAUTION:

o Radiator anti-freeze (engine coolant) should not be used in the washer system because it will damage the car's finish.

o The washer should not be operated if the washer reservoir is empty. This can dam- age the washer fluid pump.

Filler plug

Drain plug

HXGS506
Transaxle lubricant in the manual transaxle should be checked at those intervals specified in the vehicle maintenance schedule in Section 5.

Recommended Oil Use only HYUNDAI GENUINE PARTS MTF 75W/90 (API GL-4) or equivalent in the manual transaxle.

Manual Transaxle Oil Capacity The oil capacity of the manual transaxle is 2.27
U.S. quarts (2.15 liters).

G100B02A-AAT To check the Manual Transaxle Fluid Level

Park the car on level ground with the engine off.

G100B01L

6 DO-IT-YOURSELF MAINTENANCE 12

1. Using a wrench of the correct size, loosen the oil filler plug by turning it counterclock- wise and remove it with your fingers.

2. Use your finger or suitable tool to feel inside the hole. The oil level should be at its bottom edge. If it is not, check for leaks before adding oil. To refill the transaxle or bring the oil level up, add oil slowly until it reaches the proper level. Do not overfill.

3. Replace the plug and washer, screw it in with your fingers and then tighten securely with the wrench.

CHECKING THE TRANSAXLE FLUID (AUTOMATIC)

G110A01E-AAT Transaxle fluid in the automatic transaxle should be checked at those intervals specified in the vehicle maintenance schedule in Section 5.

G110C02A-AAT Transaxle Fluid Capacity The fluid capacity of the automatic transaxle is 6.45 U.S. quarts (6.1 liters).

WARNING:

The transaxle fluid level should be checked when the engine is at normal operating tem- perature. This means that the engine, radia- tor, exhaust system etc., are very hot. Exer- cise great care not to burn yourself during this procedure.

NOTE: Automatic transaxle fluid is basically a red color. As driving distance increases, the fluid color turns darkish red gradually. It is a normal condition and you should not judge the need to replace based upon the chang- ing color. You must replace the automatic transaxle fluid in accordance with intervals specified in the vehicle maintenance schedule in sec- tion 5.

G110B03A-AAT Recommended Fluid

Your Hyundai automatic transaxle is specially designed to operate with HYUNDAI GENUINE ATF, DIAMOND ATF SP-III or SK ATF SP-III. Damage caused by a nonspecified fluid is not covered by your new vehicle limited warranty.

G110D02A-AAT To Check the Transaxle Fluid Level

C090A01A

Park the car on level ground with the parking brake engaged. When the transaxle fluid level is checked, the transaxle fluid should be at normal operating temperature and the engine idling.

G110D03A

While the engine is idling, apply the brakes and move the gear selector lever from "P" to each of its other positions -- "R", "N", "D", "2", "L" -- and then return to "N" or "P". With the engine still idling:

1. Open the hood, being careful to keep hands, hair and clothing clear of any moving parts. 2. Remove the transaxle dipstick, wipe it clean, reinsert the dipstick as far as it will go, then remove it again. Now check the fluid level on the dipstick. It should be in the "HOT" range on the dipstick.

DO-IT-YOURSELF MAINTENANCE

13

Fluid level should be within "HOT" range

3.

G110D04A If the transaxle fluid level is low, use a funnel to add transaxle fluid through the dipstick tube until the level reaches the "HOT" range. Do not overfill.

WARNING:

The cooling fan is controlled by the engine coolant temperature and may sometimes op- erate even when the engine is not running. Use extreme caution when working near the blades of the cooling fan, so that you are not injured by a rotating fan blade. As the engine coolant temperature decreases, the fan will automatically shut off. This is a normal con- dition.

6 DO-IT-YOURSELF MAINTENANCE 14

CHECKING THE BRAKES

G120A01A-AAT

CAUTION:

Because brakes are essential to the safe operation of the car, it is suggested that they be checked and inspected by your Hyundai dealer. The brakes should be checked and inspected for wear at those intervals speci- fied in the vehicle maintenance schedule in Section 5.

G120B01A-AAT Checking the Brake Fluid Level

WARNING:

Use caution when handling brake fluid. It can damage your vision if it gets into your eyes. It will also damage your vehicle's paint if spilled on it and not removed immediately.

G120C02A-AAT Recommended Brake Fluid

G120E02A-AAT Adding Brake Fluid

WARNING:

Handle brake fluid carefully. It can damage your vision if it gets into your eyes. Use only DOT 3 or DOT 4 specification fluid from a sealed container. Do not allow the fluid can or reservoir to remain open any longer than required. This will avoid entry of dirt and moisture which can damage the brake sys- tem and cause improper operation.

To add brake fluid, first wipe away any dirt then unscrew the fluid reservoir cap. Slowly pour the recommended fluid into the reservoir. Do not overfill. Carefully replace the cap on the reser- voir and tighten.

Use only hydraulic brake fluid conforming to DOT 3 or DOT 4 specifications in your braking system. Follow the instructions printed on the container.

G120D01A-AAT To Check the Fluid Level

HLC5035

The fluid level in the brake fluid reservoir should be checked periodically. The level should be between the "MIN" and "MAX" marks on the side of the reservoir. If the level is at or below the "MIN" mark, carefully add fluid to bring it up to "MAX". Do not overfill.

CHECKING THE CLUTCH FLUID

G130A01A-AAT To Check the Clutch Fluid

G130B02A-AAT To Replace the Fluid

Recommended brake fluid conforming to DOT 3
or DOT 4 specification should be used. The reservoir cap must be fully tightened to avoid contamination from foreign matter or moisture.

NOTE: Do not allow any other liquids to contami- nate the brake fluid. Seal damage will result.

DO-IT-YOURSELF MAINTENANCE

AIR CONDITIONER CARE

15

G140A01A-AAT Keeping the Condenser Clean

The air conditioner condenser (and engine ra- diator) should be checked periodically for accu- mulation of dirt, dead insects, leaves, etc. These can interfere with maximum cooling efficiency. When removing such accumulations, brush or hose them away carefully to avoid bending the cooling fans.

WARNING:

Use caution when handling brake fluid. It can damage your vision if you get it in your eyes. It will also damage your vehicles paint if spilled on it and not removed immediately.

HLC5036
The clutch fluid level in the master cylinder should be checked when performing other un- der hood services. The system should be checked for leakage at the same time. Check to make certain that the clutch fluid level is between the "MAX" and "MIN" level markings on the fluid reservoir. Fill as required. Fluid loss indicates a leak in the clutch system which should be inspected and repaired immediately. Consult your Hyundai dealer.

6 DO-IT-YOURSELF MAINTENANCE 16

G140B01A-AAT Checking the Air Conditioner Opera- tion

1. Start the engine and let it run at fast idle for several minutes with the air conditioner set at the maximum cold setting. If the air coming out of the in-dash vents is not cold, have the air conditioning system inspected by your Hyundai dealer.

2.

G140D02A-AAT Checking the Compressor Drive Belt

A/C

0.315 in. (8mm)

CHANGING THE AIR CONDITIONER FILTER B145A02A-GAT (For Evaporator and Blower Unit) (If Installed)

The air conditioner filter is located in front of the evaporator unit behind the glove box. It helps to decrease the amount of pollutants entering the car.

CAUTION:

Running the air conditioning system for ex- tended periods of time with a low refrigerant level may damage the compressor.

G140C01A-AAT Lubrication

To lubricate the compressor and the seals in the system, the air conditioner should be run for at least 10 minutes each week. This is particularly important during cool weather when the air con- ditioning system is not otherwise in use.

TENSION PULLEY

CRANK PULLEY

G140D01A

When the air conditioning is being used regular- ly, the compressor drive belt tension should be checked at least once a month with the engine turned off. To check the drive belt tension, press down on the belt halfway between the engine crankshaft and compressor pulleys. Pressing with your finger, you should not be able to deflect this belt anymore than 1/3 of an inch. If the belt is too loose, have it adjusted by your Hyundai dealer.

1. Open the glove box and remove the adjust-

ing pins on both sides of the glove box.

HLC2096

DO-IT-YOURSELF MAINTENANCE

CHECKING THE FREE-PLAY

17

3. Remove the filter cover by pushing the upper

end of the filter cover.

G150A01A-AAT Steering Wheel

2. Remove the cable and the wiring from the

filter cover.

HLC2097

4. Replace the two filters. 5.

Installation is the reverse order of disassem- bly.

HLC2099

CAUTION:

Be sure to install the air conditioner filter in the direction of the arrow sign. Otherwise, it may cause noise or deterioration.

HLC2098

1.18 in. (30 mm)

HLC5008

To check the steering wheel free-play, stop the car with the wheels pointed straight ahead and gently move the steering wheel back and forth. Use very light finger pressure and be sensitive to changes in resistance that mark the limits of the free-play. If the free-play is greater than specified, have it inspected by your Hyundai dealer and adjusted or repaired if necessary.

6 DO-IT-YOURSELF MAINTENANCE 18

G160A01A-AAT Clutch Pedal

G170A01A-AAT Brake Pedal

CHECKING BRAKE PEDAL CLEARANCE

G180A01A-AAT

0.24 ~ 0.51 in. (6 ~ 13 mm)

0.12 ~ 0.31 in. (3 ~ 8 mm)

1.78 in. (45.1 mm)

G180A01L

G160A01E With the engine off, press lightly on the clutch pedal until you feel a change in resistance. This is the clutch pedal free-play. The free-play should be within the limits specified in the illustration below. If it is not, have it inspected by your Hyundai dealer and adjusted or repaired if nec- essary.

HXGS508

With the engine off, press down on the brake pedal several times to reduce the vacuum in the brake booster. Then, using your hand, press down slowly on the brake pedal until you feel a change in resis- tance. This is the brake pedal free-play. The free-play should be within the limits speci- fied in the illustration above. If it is not, have it inspected by your Hyundai dealer and adjusted or repaired if necessary.

You need a helper to check the brake pedal clearance. With the engine running, have your helper press down on the brake pedal several times and then hold it down with a force of about 110 lbs (50 kg, 490 N). The brake pedal clear- ance is the distance from the top surface of the brake pedal to the asphalt sheeting under the floor mat. If the brake pedal clearance is not within the limits specified in the illustration, have it in- spected by your Hyundai dealer and adjusted or repaired if necessary.

DO-IT-YOURSELF MAINTENANCE

19

CAUTION:

When replacing a fusible link, never use anything but a new fusible link with the same or lower amperage rating. Never use a piece of wire or a higher-rated fusible link. This could result in serious damage and create a fire hazard.

CHECKING DRIVE BELTS

G190A01A-AAT

Water Pump Pulley

CHECKING AND REPLACING FUSES G200A01A-AAT Replacing a Fusible Link

0.2~0.24 in. (5.1~6 mm)

Alternator Pulley

Bad

Good

Crankshaft Pulley

HTB186

Drive belts should be checked periodically for proper tension and adjusted if necessary. At the same time, belts should be examined for cracks, wear, fraying or other evidence of deterioration and replaced if necessary. Belt routing should also be checked to be sure there is no interference between the belts and other parts of the engine. After a belt is replaced, the new belt should be adjusted again after two or three weeks to eliminate slack resulting from initial stretching after use.

G200A01A A fusible link will melt if the electrical circuits from the battery are ever overloaded, thus pre- venting damage to the entire wiring harness. (This could be caused by a short in the system drawing too much current.) If this ever happens, have a Hyundai dealer determine the cause, repair the system and replace the fusible link. The fusible links are located in a relay box for easy inspection.

6 DO-IT-YOURSELF MAINTENANCE 20

G200B01A-AAT Replacing Accessory Fuses

1. Turn off the ignition and all other switches. 2. Open the fuse box and examine each fuse. Remove each fuse by pulling it toward you (a small "fuse puller" tool is contained in the fuse box to simplify this operation).

3. Be sure to check all other fuses even if you

find one that appears to have opened.

HLC4002

The fuse box for the lights and other electrical accessories will be found low on the dashboard on the driver's side. Inside the box you will find a list showing the circuits protected by each fuse. If any of your car's lights or other electrical accessories stop working, a blown (open) fuse could be the reason. If the fuse has opened, you will see that the metal strip inside the fuse has melted through. If you suspect a blown fuse, follow this procedure:

HLC4003

4. Replace the blown fuse by pressing a new fuse of the same rating into place. The fuse should be a snug fit. If it is not, have the fuse clip repaired or replaced by a Hyundai deal- er. If you do not have a spare fuse, you may be able to borrow a fuse of the same or lower rating from an accessory you can tempo- rarily get along without (the radio or cigarette lighter, for example). Always remember to replace the borrowed fuse.

Good

Open - Replace

G200B02L

CAUTION:

An open fuse indicates that there is a prob- lem in the electrical circuit. If you replace a fuse and it blows as soon as the accessory is turned on, the problem is serious and should be referred to a Hyundai dealer for diagnosis and repair. Never replace a fuse with anything except a fuse with the same or a lower amperage rating. A higher capacity fuse could cause damage and create a fire hazard.

NOTE: See page 6-32 for the fuse panel descrip- tions.

CHECKING THE BATTERY

G210A01A-AAT

D010B01A

WARNING:

When working with batteries, carefully ob- serve the following precautions to avoid se- rious injuries.

The fluid in the battery contains a strong solution of sulfuric acid, which is poisonous and highly corrosive. Be careful not to spill it on yourself or the car. If you do spill battery fluid on yourself, immediately do the following:

o If battery fluid is on your skin, flush the affected areas with water for at least 15
minutes and then seek medical assistance. o If battery fluid is in your eyes, rinse out your eyes with water and get medical assistance as soon as possible. While you are being driven to get medical assistance, continue to rinse your eyes by using a sponge or soft cloth saturated with water.

o If you swallow battery fluid, drink a large quantity of water or milk followed by milk of magnesia, eat a raw egg or drink vegetable oil. Get medical assistance as soon as pos- sible.

While batteries are being charged (either by a battery charger or by the vehicle's alternator), they produce explosive gases. Always observe these warnings to prevent injuries from occur- ring: o Charge batteries only in a well ventilated

o Do not permit flames, sparks or smoking in

area.

the area.

o Keep children away from the area.

DO-IT-YOURSELF MAINTENANCE

21

G210B02A-AAT Checking the Battery

Keep the battery clean. Any evidence of corro- sion around the battery posts or terminals should be removed using a solution of household bak- ing soda and warm water. After the battery terminals are dry, cover them with a light coating of grease.

PROPOSITION 65 WARNING: Battery posts, terminals, and related acces- sories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Batter- ies also contain other chemicals known to the State of California to cause cancer. Wash hands after handling.

6 DO-IT-YOURSELF MAINTENANCE 22

CHECKING ELECTRIC COOLING FANS G220A01A-AAT

POWER STEERING FLUID LEVEL

G230A03A-AAT

WARNING:

The radiator fan is controlled by engine cool- ant temperature and may sometimes operate even when the engine is not running. Use extreme caution when working near the blades of the cooling fan, so that you are not injured by a rotating fan blade. As the cool- ant temperature decreases the fan will auto- matically shut off. This is a normal condition.

G220B01A-AAT Checking Engine Cooling Fan

The engine cooling fan should come on auto- matically if the engine coolant temperature is high.

G220C01A-AAT Checking Condenser Cooling Fan

The condenser cooling fan should come on automatically whenever the air conditioner is in operation.

HLC5006
The power steering fluid level should be checked regularly. To check the power steering fluid level, be sure the engine is "OFF", then check to make certain that the power steering fluid level is between the "MAX" and "MIN" level markings on the fluid reservoir.

NOTE: Grinding noise from the power steering pump may be heard immediately after the engine is started in extremely cold conditions (below -4°F). If the noise stops during warm up, there is no abnormal function in the system. It is due to a power steering fluid character- istic in extremely cold conditions.

Recommended Fluid Use PSF-3 type fluid

NOTE: Do not start the engine when the power steering oil reservoir is empty.

G240A01A-AAT POWER STEERING HOSES

It is suggested that you check the power steer- ing hose connections for fluid leakage at those intervals specified in the vehicle maintenance schedule in Section 5. The power steering hoses should be replaced if there is severe surface cracking, pulling, scuff- ing or worn spots. Deterioration of the hose could cause premature failure.

HEADLIGHT AIMING ADJUSTMENT

DO-IT-YOURSELF MAINTENANCE

23

6. Draw the vertical line (through the center of each headlight) and the horizontal line (through the center of each headlight) on the aiming screen. And then, draw a parallel line at 0.8 in.(21
mm) under the horizontal line.

7. Adjust each cut-off line of the low beam to

the parallel line with a phillips screwdriver - VERTICAL AIMING

WARNING:

Horizontal aiming should be adjusted by an authorized Hyundai dealer.

G250A01A-AAT FOR MORE INFORMATION ABOUT YOUR HYUNDAI

G290A04A-AAT Before performing aiming adjustment, make sure of the following.

If you desire additional information about main- taining and servicing your Hyundai, you may purchase a factory Shop Manual at your Hyundai dealer's parts department. This is the same manual used by dealership technicians and while it is highly technical it can be useful in obtaining a better understanding of your car and how it works.

1. Keep all tires inflated to the correct pressure. 2. Place the vehicle on level ground and press the front bumper & rear bumper down sever- al times. Place vehicle at a distance of 118
in. (3m) from the test wall.

3. See that the vehicle is unloaded (except for full levels of coolant, engine oil and fuel, and spare tire, jack, and tools). Have the driver or equivalent weight placed in driver's seat.

4. Clean the headlight lenses and turn on the

headlights (Low beam).

5. Open the hood.

Vertical Aiming

G290A01A-1

SPECIFICATIONS:

"H"; Horizontal center line of headlights from ground : 25.8 in. (656 mm)

"W"; Distance between each headlight center : 42.4 in. (1,078 mm)

"L"; Distance between the headlights and the wall that the lights are tested against: 118 in. (3,000 mm).

REPLACEMENT OF LIGHT BULBS

G260A02A-AAT Before attempting to replace a light bulb, be sure the switch is turned to the "OFF" position. The next paragraph shows how to reach the light bulbs so they may be changed. Be sure to replace the burned-out bulb with one of the same number and wattage rating. See page 6-31 for the wattage descriptions

CAUTION:

Keep the lamps out of contact with petro- leum products, such as oil, gasoline, etc.

6 DO-IT-YOURSELF MAINTENANCE 24

G290B02A-AAT Adjustment After Headlight Assembly Replacement

0.8 in. (21mm)

Horizontal line

0.55 in. (14mm)

Vertical line

"P"

Ground line

G290B01A-1

Cut-off line

If the vehicle has had front body repair and the headlight assembly has been replaced, the head- light aiming should be checked using an aiming screen as shown in the illustration. Turn on the headlight switch. (Low Beam Position)

1. Adjust headlights so that main axis of light is parallel to center line of the body and is aligned with point "P" shown in the illustra- tion.

2. Dotted lines in the illustration show the cen-

ter of headlights.

DO-IT-YOURSELF MAINTENANCE

25

G270A03A-AAT Headlight Bulb

1. Allow the bulb to cool. Wear eye protection. 2. Open the engine hood. 3. Always grasp the bulb by its plastic base,

avoid touching the glass.

4. Using a socket wrench of the correct size, remove the headlight assembly mounting bolts.

HLC5033

HLC5034-1
5. Disconnect the power cord from the bulb

base in the back of the headlight.

7. Push the bulb spring to remove the headlight

bulb.

HLC5010

6. Remove the dust cover.

HLC5009

6 DO-IT-YOURSELF MAINTENANCE 26

HLC5011

G270A03O

8. Remove the protective cap from the replace- ment bulb and install the new bulb by match- ing the plastic base with the headlight hole. Re-attach the bulb spring and install the dust cover. Reconnect the power cord.

9. Use the protective cap and carton to dispose

of the old bulb.

10.Check for proper headlight aim.

WARNING:

The halogen bulb contains gas under pres- sure and if impacted could shatter, resulting in flying fragments. Always wear eye protec- tion when servicing the bulb. Protect the bulb against abrasions or scratches and against liquids when lighted. Turn the bulb on only when installed in a headlight. Re- place the headlight if damaged or cracked. Keep the bulb out of the reach of children and dispose of the used bulb with care.

G270B01A-GAT Front Turn Signal light / Position Light

HLC5034
1. Disconnect the power cord from the bulb.

(2)

(1)

G270D01TB-AAT Rear Combination Light 4 Door

DO-IT-YOURSELF MAINTENANCE

27

2. Remove the mounting screws as shown with

a phillips screwdriver.

4 Door

HLC5012

2. To replace the front turn signal light (1) or position light (2), take it out from the bulb holder by turning it counterclockwise. Install the new bulb.

3.

3 Door

G270D01A

3 Door

(2)

1. Open the trunk lid/tail gate.

HLC5015

(3)

(1)

(3)

(1)

(2)

G270D02A

HLC5016

6 DO-IT-YOURSELF MAINTENANCE 28

3. To replace the rear combination light (stop/ tail light, turn signal light or back-up light), take it out from the bulb holder by turning it counterclockwise.

G270C01TB-AAT Luggage Compartment Light (If Installed) 3 Door

4 Door

(1) Stop/Tail Light (2) Turn Signal Light (3) Back-up Light

4.

Install the new bulb.

2. Disconnect the power cord.

HTB283

1. Remove the cover with a flat-head screw-

driver.

HLC5014

3. Replace with a new bulb.

HTB284

G270G01A-AAT Interior Light (Map Light) (If Installed)

G270H01A-AAT Interior Light

DO-IT-YOURSELF MAINTENANCE

29

HLC5017

2. Replace with a new bulb.

HLC5018

1. Remove the cover with a flat-head screw-

driver.

1. Remove the cover with a flat-head screw-

driver.

HLC5019

6 DO-IT-YOURSELF MAINTENANCE 30

2. Replace with a new bulb.

HLC5020

BULB WATTAGES

G280A03A-AAT

4 DOOR

3 DOOR

DO-IT-YOURSELF MAINTENANCE

31

12

10

11

11

10

12

G280A02A

No.

Part Name

Front Position Light Headlight (High/Low) Front Turn Signal Light Interior Light (Map Light) (If Installed) Interior Light Front Fog Light (If Installed) Front Side Marker Light

Wattage

60/55

27
10
10
27

No.

10
11
12

Part Name

Rear Combination Light

Turn Signal Light Stop/Tail Light Back-up Light

High Mounted Rear Stop Light (If Installed) Rear Side Marker Light Luggage Compartment Light (If Installed) License Plate Light

Wattage

27

27/8(4 Door), 28/8(3 Door)

17
17

6 DO-IT-YOURSELF MAINTENANCE 32

FUSE PANEL DESCRIPTION

G200C02A-GAT Engine Compartment

DESCRIPTION ALT

FUSIBLE

LINK

BATTERY

LAMP ECU IGN

RAD FAN BLOWER

ABS ABS

P/WDW

COND FAN

FUSE RATING

PROTECTED COMPONENTS

120A 50A 50A 20A 30A 20A 30A 30A 30A 30A 20A

Charging (Generator) Fuse 6, 7, 8, 9, Horn fuse, Room lamp fuse Head lamp fuse, Front fog lamp fuse, Tail lamp relay, H/LP washer fuse Engine control relay, Generator, Fuel pump relay, ECU #3 fuse Ignition power source, Start relay Radiator fan control Blower control ABS control, ABS bleeding connector ABS control, ABS bleeding connector Power window Condenser fan control

NOTE: Not all fuse panel descriptions in this manual may be applicable to your vehicle. It is accurate at the time of printing. When you inspect the fuse box on your vehicle, refer to the fuse box label.

HLC5027

DESCRIPTION

FUSE RATING

PROTECTED COMPONENTS

DO-IT-YOURSELF MAINTENANCE

33

ECU #1

A/CON COMP

HORN

TAIL LH

TAIL RH H/LP LH H/LP RH

FRONT FOG

ROOM LP

AUDIO

ECU #2

ECU#3

FUSE

H/L WASHER F/PUMP CHK (E50)

10A

10A 10A

10A

10A 10A 10A 15A

10A

15A

15A

10A 25A

Radiator fan, Condenser fan, ECM, Oxygen sensor, Purge control valve, SMATRA, Glow plug relay, Heater relay, Stop lamp switch A/C relay Horn relay Illumination lamps, Left rear combination lamp, License lamp, DRL control, Position lamp, H/LP washer relay Right rear combination lamp, License lamp, Position lamp Left head lamp, DRL control, Instrument cluster Right head lamp Front fog lamp relay Instrument cluster, Courtesy lamp, Trunk room lamp, ETACM, DLC, Door warning, Multipurpose check connector Audio, Digital clock, Power antenna, A/C switch, Rear fog lamp switch Idle speed actuator, ECM, Camshaft position sensor, EGR actuator, Throttle plate actuator ECM Head lamp washer motor Fuel pump relay, Fuel pump motor

6 DO-IT-YOURSELF MAINTENANCE 34

G200E01A-GAT Inner Panel

FUSE

FUSE RATING

PROTECTED COMPONENTS

10

11
12
13
14
15
16
17
18

10A

10A 10A 15A

10A

10A 10A 10A 20A

10A

20A 20A 10A 10A 15A 10A 10A 20A

Hazard warning, Back-up lamp switch, Transaxle range switch, A/T shift & key lock control module ETACM, Pre-Excitation resistor, Instrument cluster, Seat belt timer Instrument cluster Air bag ECM, A/T shift lever, Transaxle range switch, Mass air flow sensor, Vehicle speed sensor, Water sensor Power door lock Hazard warning, ETACM Stop lamp, A/T shift lever, A/T key interlock solenoid Rear window defogger Head lamp, Power window, Head lamp leveling, Head lamp washer, ETACM, Front fog lamp, Blower control, Rear intermittent washer, Fuel filter relay Front wiper & washer Seat warmer ABS control, ABS bleeding Digital clock, Audio, A/T shift & key lock control module Cigarette lighter Power outside mirror Rear window & outside mirror defogger Rear wiper

HLC5031

EMISSION CONTROL SYSTEMS

Emission Control System ............................................. 7-2
Catalytic Converter ....................................................... 7-3

7 EMISSION CONTROL SYSTEMS

EMISSION CONTROL SYSTEM

H010A01A-AAT Your Hyundai is equipped with an emission control system to meet all requirements of the U.S. Environmental Protection Agency or Cali- fornia Air Resources Board. There are three emission control systems which are as follows.

1) Crankcase Emission Control System 2) Evaporative Emission Control System 3) Exhaust Emission Control System

In order to ensure the proper function of the emission control systems, it is recommended that you have your car inspected and main- tained by an authorized Hyundai dealer in ac- cordance with the maintenance schedule in this manual.

H010B01A-AAT 1. CRANKCASE EMISSION CONTROL

SYSTEM

The positive crankcase ventilation system is employed to prevent air pollution caused by blow-by gases being emitted from the crank- case. This system supplies filtered fresh air to the crankcase through the air intake hose. In- side the crankcase, the fresh air mixes with blow-by gases, then passes through the PCV valve into the induction system.

H010C01S-AAT 2. Evaporative Emission Control (Includ- ing ORVR: Onboard Refueling Vapor Recovery) System

The Evaporative Emission Control System is designed to prevent fuel vapors from escaping into the atmosphere. (The ORVR system is designed to allow the vapors from the fuel tank to be loaded into a canister while refueling at the gas station, pre- venting the escape of fuel vapors into the atmo- sphere.)

Canister

Fuel vapors generated inside the fuel tank are absorbed and stored in the onboard canister. When the engine is running, the fuel vapors absorbed in the canister are drawn into the induction system through the purge control so- lenoid valve.

Purge Control Solenoid Valve (PCSV)

The purge control solenoid valve is controlled by the Engine Control Module (ECM); when the engine coolant temperature is low during idling, the PCSV closes so that evaporated fuel is not taken into the engine. After the engine warms- up during ordinary driving, the PCSV opens to introduce evaporated fuel to the engine.

H010D01A-AAT 3. EXHAUST EMISSION CONTROL SYSTEM

The Exhaust Emission Control System is a highly effective system which controls exhaust emissions while maintaining good vehicle performace.

EMISSION CONTROL SYSTEMS

WARNING:

o Remember that your Hyundai dealer is

your best source of assistance.

o Do not stop your Hyundai over any com- bustible material such as grass, paper, leaves or rags. These materials might contact the hot catalytic converter and a fire might result.

CATALYTIC CONVERTER

H020A01A-AAT

Catalytic Converter

HLC5022

All Hyundai vehicles are equipped with a mono- lith type three-way catalytic converter to reduce the carbon monoxide, hydrocarbons and nitrogen oxides contained in the exhaust gas. Exhaust gases passing through the cata- lytic converter cause it to operate at a very high temperature. The introduction of large amounts of unburned gasoline into the ex- haust may cause the catalytic converter to overheat and create a fire hazard. This risk may be reduced by observing the following:

WARNING:

o Use unleaded fuel only. o Maintain the engine in good operating condition. Extremely high catalytic con- verter temperatures can result from im- proper operation of the electrical, igni- tion or multiport electronic fuel injec- tion.

o If your engine stalls, pings, knocks, or is hard to start, have your Hyundai dealer inspect and repair the problem as soon as possible.

o Avoid driving with a very low fuel level. Running out of gasoline may cause the engine to misfire and result in damage to the catalytic converter.

o Avoid idling the engine for periods longer

than 10 minutes.

o The vehicle should not be pushed or pulled to get started. This may cause the catalytic converter to overheat and create a fire hazard.

o Do not touch the catalytic converter or any other part of the exhaust system while the catalytic converter is hot. Shut off the engine, wait for at least one hour before touching the catalytic converter or any other part of the exhaust system.

CONSUMER INFORMATION & REPORTING SAFETY DEFECTS

Vehicle Identification Number (VIN) ............................. 8-2
Engine Number ............................................................. 8-2
Recommended Inflation Pressures .............................. 8-3
Snow Tires.................................................................... 8-3
Tire Chains ................................................................... 8-4
Tire Rotation ................................................................. 8-4
Tire Balancing ............................................................... 8-5
Tire Traction.................................................................. 8-5
When to Replace Tires ................................................. 8-5
Spare Tire and Tools .................................................... 8-6
Warranties for Your Hyundai Vehicle ........................... 8-6
Consumer Information .................................................. 8-7
Reporting Safety Defects ............................................. 8-9

8 CONSUMER INFORMATION & REPORTING SAFETY DEFECTS

VEHICLE IDENTIFICATION NUMBER (VIN)

ENGINE NUMBER

TIRE

I010A02A-AAT

I010B01A-AAT

I020A01A-AAT Tire information

The tires supplied on your new Hyundai are chosen to provide the best performance for normal driving.

I010A01A-1
The vehicle identification number (VIN) is the number used in registering your car and in all legal matters pertaining to its ownership, etc. It can be found in four different places on your car:

The engine number is stamped on the engine block as shown in the drawing.

F040A02TB-1

1. On the bulkhead between the engine and

passenger compartments.

2. On the left top side of the instrument panel where it can be seen by looking down through the windshield. 3. Door edge post 4. On the lower side of the center pillar outer

panel.

CONSUMER INFORMATION & REPORTING SAFETY DEFECTS

I040A01A-AAT SNOW TIRES

If you equip your car with snow tires, they should be the same size and have the same load capacity as the original tires. Snow tires should be installed on all four wheels; otherwise, poor handling may result. Snow tires should carry 4 psi (28 kPa) more air pressure than the pressure recommended for the standard tires on the tire label on the glove box, or up to the maximum pressure shown on the tire sidewall whichever is less. Do not drive faster than the speed limit when your car is equipped with snow tires.

I030A02A-AAT RECOMMENDED INFLATION PRESSURES

These pressures were chosen to provide the most satisfactory combination of ride comfort, tire wear and stability under normal conditions. Tire pressures should be checked at least monthly. Proper tire inflation pressures should be maintained for these reasons: o Lower-than-recommended tire pressures cause uneven tread wear and poor handling. o Higher-than-recommended tire pressures in- crease the chance of damage from im- pacts and cause uneven tread wear.

CAUTION:

Always observe the following:

I030A01A The tire label located in the glove box gives the tire pressures recommended for your car.

RECOMMENDED INFLATION PRESSURE-COLD

TIRE SIZE

P175/70R13
P185/60R14
T105/70R14
T105/70D14

PRESSURE, kPa (PSI)

Up to 2 persons Front Rear 207(30) 207(30) 207(30) 207(30)

Up to MAX. load Front Rear 230(33) 230(33) 230(33) 230(33)

TEMPERARY USE ONLY

414(60)

o Check pressures when the tires are cold. That is, after the car has been parked for at least three hours and hasn't been driven more than one mile or 1.6 km since starting up.

o Check the pressure of your spare tire each time you check the pressure of other tires.

8 CONSUMER INFORMATION & REPORTING SAFETY DEFECTS

I050A03A-AAT TIRE CHAINS

I060A02A-AAT TIRE ROTATION

Tire chains, if necessary, should be installed on the front wheels. Be sure that the chains are installed in accordance with the manufacturer's instructions.

To minimize tire and chain wear, do not con- tinue to use tire chains when they are no longer needed.

WARNING:

o When driving on roads covered with snow or ice, drive at less than 20 mph (30 km/h). o Use the SAE "S" class or wire & plastic

chains.

o If you have noise caused by chains contacting the body, retighten the chain to avoid contact with the vehicle body. o To prevent body damage, retighten the

chains after driving 0.3~0.6 miles.

HEF-241

Tires should be rotated every 7,500 miles (12,000 km). If you notice that tires are wear- ing unevenly between rotations, have the car checked by a Hyundai dealer so the cause may be corrected. After rotating, adjust the tire pressures and be sure to check the wheel nut torque.

WARNING:

tire rotation.

o Do not use the temporary spare tire for

o Do not mix bias ply and radial ply tires under any circumstances. This may cause unusual handling characteristics that could result in death, serious injury, or property damage.

CONSUMER INFORMATION & REPORTING SAFETY DEFECTS

I070A01A-AAT TIRE BALANCING

A tire that is out of balance may affect handling and tire wear. The tires on your Hyundai were balanced before the car was delivered but may need balancing again during the years you own the car. Whenever a tire is dismounted for repair, it should be rebalanced before being reinstalled on the car.

I080A01A-AAT TIRE TRACTION

Tire traction can be reduced if you drive on worn tires, tires that are improperly inflated or on slippery road surfaces. Tires should be replaced when tread wear indicators appear. To reduce the possibility of losing control, slow down when- ever there is rain, snow or ice on the road.

I090A01A-AAT WHEN TO REPLACE TIRES

0.06 in. (1.6 mm)

Wear indicator

HGK248

The original tires on your car have tread wear indicators. The tread wear indicators appear when the tread depth is 0.06 in. (1.6 mm). The tire should be replaced when these appear as a solid bar across two or more grooves of the tread. Always replace your tires with those of the recommended size. If you change wheels, the new wheel's rim width and offset must meet Hyundai specification.

WARNING:

o Driving on worn-out tires is dangerous! Worn-out tires can cause loss of brak- ing effectiveness, steering control and traction. When replacing tires, never mix radial and bias ply tires on the same car. If you replace radial tires with bias- ply tires, they must be installed in sets of four.

o Using tires and wheels of other than the recommended sizes could cause unusual handling characteristics that could cause death, serious injury, or property damage.

o Wheels that do not meet Hyundai's dimensional specifications may fit poorly and result in damage to the vehicle, including broken wheel studs.

8 CONSUMER INFORMATION & REPORTING SAFETY DEFECTS

I100A02E-AAT SPARE TIRE AND TOOLS

I110A01A-AAT SHOP MANUAL

A Hyundai Shop Manual is available from your authorized Hyundai dealer. It's written for pro- fessional technicians, but is simple enough for most mechanically-inclined owners to under- stand.

Your Hyundai is delivered with the following:

I100A01A

Spare tire and wheel Wheel nut wrench, Wrench bar Jack

WARRANTIES FOR YOUR HYUNDAI VEHICLE

I120A03A-AAT o New vehicle 60 Months/60,000 Miles Limited

Warranty.

o New vehicle 120 Months/100,000 Miles Lim- ited Powertrain Warranty (original owner only).

o Anti-Perforation Limited Warranty o Emission Defect Warranty - Federal Ve-

o California Emission Control System War-

ranty (if applicable)

o Emission Performance Warranty Federal

o Replacement Parts and Accessories Limited

hicle

vehicle

Warranty

NOTE: Detailed warranty information is provided in your Hyundai Owner's Handbook.

CONSUMER INFORMATION

I130A01A-AAT This consumer information has been prepared in accordance with regulations issued by the National Highway Traffic Safety Administration of the U.S. Department of Transportation. It provides the purchasers and/or prospective purchasers of Hyundai automobiles with infor- mation on uniform tire quality grading. Your Hyundai dealer will help answer any questions you may have as you read this information.

CONSUMER INFORMATION & REPORTING SAFETY DEFECTS

I130B03A-AAT Tire Quality Grading

Department of Transportation quality grades - All passenger vehicle tires must conform to Federal Safety Standards in addition to these grades. These quality grades are molded on the sidewall.

Treadwear - The treadwear grade is a com- parative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For ex- ample, a tire graded 150 would wear one and a half (1 - 1/2) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to varia- tions in driving habits, service practices and differences in road characteristics and cli- mate.

Traction AA, A, B, C - The traction grades, from highest to lowest, are AA, A, B, and C. Those grades represent the tire's ability to stop on wet pavement as measured under controlled conditions on specified government test surfac- es of asphalt and concrete. A tire marked C may have poor traction performance.

WARNING:

The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.

Temperature A, B, C - The temperature grades are A (the highest), B, and C, repre- senting the tire's resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor labo- ratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law.

8 CONSUMER INFORMATION & REPORTING SAFETY DEFECTS

WARNING:

The temperature grade for this tire is es- tablished for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.

Uniform Tire Quality Grading - Quality grades can be found on the tire sidewall between the tread shoulder and the maximum section width. For example: Treadwear 200 Traction AA Temperature A

I130D03A-AAT Hyundai motor vehicles are designed and manufactured to meet or exceed all applicable safety standards.

Southern Region: Alabama, Arkansas, Flor- ida, Georgia, Louisiana, Mississippi, North Caro- lina, South Carolina, Oklahoma, Tennessee, Texas.

For your safety, however, we strongly urge you to read and follow all directions in this Owner's Manual, particularly the information under the headings "NOTE", "CAUTION" and "WARNING".

If, after reading this manual, you have any questions regarding the operation of your vehi- cle, please contact your nearest Hyundai Motor America Regional Office as listed below:

Eastern Region : Connecticut, Delaware, Maine, Maryland, Massachusetts, New Hampshire, New Jersey, New York, Pennsylvanina, Rhode Is- land, Vermont, Virginia, West Virginia.

Eastern Region 1100 Cranbury South River Road Jamesburg, NJ 08831
(800) 633-5151

Southern Region 270 Riverside Parkway, Suite A Austell, GA 30168
(800) 633-5151

Central Region: Illinois, Indiana, Missouri, lowa, Kansas, Kentucky, Michigan, Minne- sota, Nebraska, North Dakota, South Dakota, Ohio, Wisconsin.

Central Region 1705 Sequoia Drive Aurora, Illinois 60506
(800) 633-5151

Western Region: Alaska, Hawaii, Arizona, California, Colorado, ldaho, Montana, Nevada, New Mexico, Oregon, Texas, Utah, Washing- ton, Wyoming.

Western Region 10550 Talbert Avenue P.O.Box 20850
Fountain Valley, California 92728-0850
(800) 633-5151

CONSUMER INFORMATION & REPORTING SAFETY DEFECTS

To contact NHTSA, you may either call the Auto Safety Hotline toll-free at 1-888-327-4236 or write to: NHTSA, U.S. Department of Transportation, Washington. D.C. 20590. You can also obtain other information about motor vehicle safety from the Hotline.

REPORTING SAFETY DEFECTS

I130C02A-AAT If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National High- way Traffic Safety Administration (NHTSA) in addition to notifying HYUNDAI MOTOR AMERICA. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. How- ever, NHTSA cannot become involved in individual problems between you, your dealer, or HYUNDAI MOTOR AMERICA.

VEHICLE SPECIFICATIONS

Measurement ................................................................ 9-2
Engine ........................................................................... 9-3
Lubrication Chart ........................................................... 9-4

9 VEHICLE SPECIFICATIONS

J010A01A-AAT MEASUREMENT

Item

Overall length

Overall width

Overall height (unladen)

Wheel base

Wheel tread

Front

Rear

J020A01A-AAT POWER STEERING

Type

Wheel free play

Rack stroke

Oil pump type

J060A01A-AAT FUEL SYSTEM

Fuel tank

capacity

in. (mm)

J030A03A-AAT TIRE

4 DOOR

3 DOOR

167.7 (4260)

165.9 (4215)

66.1 (1680)