o If the interior of the car is hot when you first get in, open the windows for a few minutes to expel the hot air.
o When you are using the air conditioning system, keep all windows closed to keep hot air out.
o When moving slowly, as in heavy traffic, shift to a lower gear. This increases engine speed, which in turn increases the speed of the air conditioning compressor.
o On steep grades, turn the air conditioner off to avoid the possibility of the engine over- heating.
o During winter months or in periods when the air conditioner is not used regularly, run the air conditioner once every month for a few minutes. This will help circulate the lubri- cants and keep your system in peak operat- ing condition.
DEFROSTING/DEFOGGING
B720A05A-AAT
FEATURES OF YOUR HYUNDAI
71
B720B01A-1
B720B02A-1
Use the heating/ventilation system to defrost or defog the windshield:
To remove frost or exterior fog on the windshield: o Activate the windshield wipers and washer to remove
To remove interior fog on the windshield: o Set the air intake control to the fresh air ( ) position. o Set the air flow control to the defrost ( ) position.
(The air conditioning will be turned on automatically.)
o Set the temperature control to the desired position. o Set the fan speed control between "1" and "4" position.
light frost and moisture.
o Set the air intake control to the fresh ( ) position. o Set the air flow control to the defrost ( ) position.
(The air conditioning will be turned on automatically.)
o Set the temperature control to warm. o Set the fan speed control to position "3" or "4".
NOTE: When the A/C is operated continuously on the floor-defrost level ( ) or defrost level ( ), it may cause fog to form on the exterior windshield. If this occurs, set the air flow control to the face level position ( ) and fan speed control to the low position.
1FEATURES OF YOUR HYUNDAI
72
AIR CONDITIONER FILTER (For Evaporator and Blower unit)
B760A05A-GAT (If Installed)
Outside air
Inside of a vehicle
Filter Evaporator core
Blower
Inside air
B760A01Y
The air conditioner filter is located in front of the evaporator unit behind the glove box. It operates to decrease the amount of pollut- ants entering the car. To replace the air conditioner filter, refer to the page 6-16.
CAUTION:
o Replace the filter every 12,000 miles (20,000 km) or once a year. If the car is being driven in severe conditions such as dusty, rough roads, more frequent air conditioner filter inspections and changes are required.
o When the air flow rate is decreased, it must be checked at an authorized dealer.
STEREO SOUND SYSTEM
B750A02A-AAT How Car Audio Works FM reception
Ionosphere
AM reception
Ionosphere
FM radio station
Mountains
FEATURES OF YOUR HYUNDAI
73
Unobstructed
area
Buildings
B750A02L
Obstructed area
Iron bridges
B750A03L
AM broadcasts can be received at greater dis- tances than FM broadcasts. This is because AM radio waves are transmitted at low fre- quencies. These long, low frequency radio waves can follow the curvature of the earth rather than travelling straight out into the atmo- sphere. In addition, they curve around ob- structions so that they can provide better signal coverage.
FM broadcasts are transmitted at high fre- quencies and do not bend to follow the earth's surface. Because of this, FM broadcasts gen- erally begin to fade at short distances from the station. Also, FM signals are easily affected by buildings, mountains, or other obstructions. These can result in certain listening conditions which might lead you to believe a problem exists with your radio. The following conditions are normal and do not indicate radio trouble:
B750A01L
AM and FM radio signals are broadcast from transmitter towers located around your city. They are intercepted by the radio antenna on your car. This signal is then received by the radio and sent to your car speakers. When a strong radio signal has reached your vehicle, the precise engineering of your audio system ensures the best possible quality re- production. However, in some cases the sig- nal coming to your vehicle may not be strong and clear. This can be due to factors such as the distance from the radio station, closeness of other strong radio stations or the presence of buildings, bridges or other large obstruc- tions in the area.
1FEATURES OF YOUR HYUNDAI
74
B750B03Y-AAT Using a cellular phone or a two-way radio
When a cellular phone is used inside the vehi- cle, noise may be produced from the audio equipment. This does not mean that something is wrong with the audio equipment. In such a case, use the cellular phone at a place as far as possible from the audio equipment.
WARNING:
Don't use a cellular phone when you are driving. Stop at a safe place to use a cellular phone.
B750A04L
B750A05L
o Fading - As your car moves away from the radio station, the signal will weaken and sound will begin to fade. When this occurs, we suggest that you select another stronger station.
o Flutter/Static - Weak FM signals or large obstructions between the transmitter and your radio can disturb the signal causing static or fluttering noises to occur. Reducing the tre- ble level may lessen this effect until the disturbance clears.
o Station Swapping - As an FM signal weak- ens, another more powerful signal near the same frequency may begin to play. This is because your radio is designed to lock onto the clearest signal. If this occurs, select another station with a stronger signal.
o Multi-Path Cancellation - Radio signals be- ing received from several directions can cause distortion or fluttering. This can be caused by a direct and reflected signal from the same station, or by signals from two stations with close frequencies. If this occurs, select another station until the con- dition has passed.
AUDIO SYSTEM
H210A01O-AAT STEREO RADIO OPERATION (H215) (If Installed)
2. FADER Control Knob
5. TUNE/SEEK Select Button
4. BAND Selector
FEATURES OF YOUR HYUNDAI
75
6. PRESET Station Select Button
3. BASS/TREBLE Control Knob
1. POWER ON-OFF, BALANCE, VOLUME, SCAN Control Knob
H210A01O
1FEATURES OF YOUR HYUNDAI
76
H210B04O-AAT 1. POWER ON-OFF/VOLUME Control
Knob
The radio unit may be operated when the igni- tion key is in the "ACC" or "ON" position. Rotate the knob clockwise to switch the radio unit on and to increase the volume. The LCD shows the radio frequency in the radio mode. Turn the knob counterclockwise to re- duce the volume and to switch the radio unit off.
BAL (Balance Control) Knob
Pull and turn the control knob clockwise to emphasize right speaker sound (left speaker sound will be attenuated). When the control knob is turned counterclockwise, left speaker sound will be emphasized (right speaker sound will be attenuated). After adjusting the balance, push the knob again to use the other function.
SCAN Knob
When the scan knob is pressed, the frequency will increase and the receivable stations will be tuned in one after another, receiving each sta- tion for 5 seconds. To stop scanning, press the scan knob again.
2. FAD (Fader Control) Knob
Turn the control knob counterclockwise to em- phasize front speaker sound (rear speaker sound will be attenuated). When the control knob is turned clockwise, rear speaker sound will be emphasized (front speaker sound will be attenuated).
3. BASS Control Knob
Press to pop the knob out and turn to the left or right for the desired bass tone.
TREBLE Control Knob.
Pull the bass control knob further out. Turn to the left or right for the desired treble tone.
4. BAND Selector
FM AM
Pressing the button changes the AM, FM1
and FM2 bands. The mode selected is dis-
played on LCD.
5. TUNE (Manual) Select Button
Press the ( ) side or ( ) side to increase or to decrease the frequency. With the button held down for 1 sec. or more, the stop signal (broad- casting radio wave) is ignored and channel selection continues.
SEEK Operation (Automatic Channel Selection)
Press the TUNE select button for 1 sec. or more. When the ( ) side is pressed, the unit will automatically tune to the next higher frequency and when the ( ) side is pressed, it will automa- tically tune to the next lower frequency.
6. PRESET STATION SELECT Button
Six (6) stations for AM, FM1 and FM2 respec- tively can be preset in the electronic memory circuit on this unit.
HOW TO PRESET STATIONS
Six AM and twelve FM stations may be pro- grammed into the memory of the radio. Then, by simply pressing the band select button and/or one of the six station select buttons, you may recall any of these stations instantly. To pro- gram the stations, follow these steps:
o Press band selector to set the band for AM,
FM1, and FM2.
o Select the desired station to be stored by
seek, scan or manual tuning.
o Determine the preset station select button
you wish to use to access that station.
FEATURES OF YOUR HYUNDAI
77
o Press the station select button for more than two seconds. A select button indicator will show in the display indicating which select button you have depressed. You should then release the button, and pro- ceed to program the next desired station. A total of 18 stations can be programmed by selecting one AM and two FM stations per button.
o When completed, any preset station may
be recalled by selecting AM, FM1 or FM2
band and the appropriate station button.
CAUTION:
o Do not place beverages close to the audio system. The audio system mecha- nism may be damaged if you spill them. o Do not impact on the audio system, or the audio system mechanism could be damaged.
1FEATURES OF YOUR HYUNDAI
78
H240A01O-GAT STEREO RADIO OPERATION (H245) (If Installed)
5. BAND Selector
3.
TREBLE/FADER Control Knob (TREB/FAD)
6. PRESET Buttons
2. BASS/BALANCE Control Knob (BASS/BAL)
4. TUNE/SEEK Select Button
7. SCAN Button
1. POWER ON/OFF, VOLUME Control Knob
H240A01O
FEATURES OF YOUR HYUNDAI
79
H240B04O-AAT 1. POWER ON-OFF Control Knob
The radio unit may be operated when the igni- tion key is in the "ACC" or "ON" position. Press the knob to switch the power on. The LCD shows the radio frequency in the radio mode or the tape direction indicator in the tape mode. To switch the power off, press the knob again.
VOLUME Control
Rotate the knob clockwise to increase the vol- ume and turn the knob counterclockwise to reduce the volume.
2. BASS Control Knob
Press to pop the knob out and turn to the left or right for the desired bass tone.
BAL (Balance Control) Knob
Pull the bass control knob further out.Turn the control knob clockwise to emphasize right speaker sound (left speaker sound will be attenuated). When the control knob is turned counterclock- wise, left speaker sound will be emphasized (right speaker sound will be attenuated).
3. TREB (Treble Control) Knob
Press to pop the knob out and turn to the left or right for the desired treble tone.
FAD (Fader Control) Knob
Pull the treble control knob further out. Turn the control knob counterclockwise to em- phasize front speaker sound (rear speaker sound will be attenuated). When the control knob is turned clockwise, rear speaker sound will be emphasized (front speaker sound will be attenuated).
4. TUNE (Manual) Select Button
Press the ( ) side or ( ) side to increase or to decrease the frequency. Press either button and hold down to continuously scroll. Release but- ton once the desired station is reached.
SEEK Operation (Automatic Channel Selection)
Press the TUNE select button 0.5 sec or more. Releasing it will automatically tune to the next available station with a beep sound.
When the ( ) side is pressed longer than 0.5
second, releasing will automatically tune to the
next higher frequency and when the ( ) side
is pressed longer than 0.5 second, releasing
will automatically tune to the next lower fre-
quency.
5. BAND Selector
FM/AM
Pressing the button changes the AM, FM1
and FM2 bands. The mode selected is dis-
played on LCD.
6. PRESET STATION SELECT Button
Six (6) stations for AM, FM1 and FM2 respec- tively can be preset in the electronic memory circuit on this unit.
HOW TO PRESET STATIONS
Six AM and twelve FM stations may be pro- grammed into the memory of the radio. Then, by simply pressing the band select button and/or one of the six station select buttons, you may recall any of these stations instantly. To pro- gram the stations, follow these steps:
!
CAUTION:
o Do not place beverages close to the audio system. The audio system mecha- nism may be damaged if you spill them. o Do not impact on the audio system, or the audio system mechanism could be damaged.
1FEATURES OF YOUR HYUNDAI
80
o Press band selector to set the band for AM,
FM1, and FM2.
o Select the desired station to be stored by
seek or manual tuning.
o Determine the preset station select button
you wish to use to access that station.
o Press the station select button for more than two seconds. A select button indicator will show in the display indicating which select button you have depressed. The frequency display will flash after it has been stored into the memory with a beep sound. You should then release the button, and proceed to program the next desired sta- tion. A total of 18 stations can be pro- grammed by selecting one AM and two FM stations per button.
o When completed, any preset station may
be recalled by selecting AM, FM1 or FM2
band and the appropriate station button.
7. SCAN Button
When the scan button is pressed, the frequency will increase and the receivable stations will be tuned in one after another, receiving each sta- tion for 5 seconds. To stop scanning, press the scan button again.
FEATURES OF YOUR HYUNDAI
81
H240C01O-GAT CASSETTE TAPE PLAYER OPERATION (H245) (If Installed)
3. TAPE PROGRAM Button
6. TAPE SLOT
2. AUTO MUSIC SELECT Button
4. EJECT Button
1.
FF/REW Button
5. DOLBY SELECT Button
H240A01O
1FEATURES OF YOUR HYUNDAI
82
H240A03O-AAT 1. FF/REW Button
o The FF (fast forward tape winding) starts when the button is pressed during PLAY or REW.
o PLAY starts when the button is press-
ed again during FF.
o REW (rewinding) starts when the button
is pressed during PLAY or FF.
o PLAY starts when the button is press-
ed again during the REW.
2. AUTO MUSIC SELECT Button
Press the button to find the starting point of each song in a prerecorded music tape. The quiet space between songs (must have at least a 4 sec. gap) can be identified by the AUTO MUSIC SELECT button.
o Pressing the button will play the beginn-
ing of the next music segment.
o Pressing the button will start replay at the beginning of the music just listened to.
3. TAPE PROGRAM Button
This allows you to play the reverse side of the tape by merely pressing the program button. An arrow will appear in the display to show tape direction.
NOTE: When tape operation is abnormal or ER8 fault code is displayed, press the eject button more than 5 seconds to reset the deck function.
4. EJECT Button
o When the EJECT button is pressed with a
cassette loaded, the cassette will eject.
o When the EJECT button is pressed during
FF/REW, the cassette will eject.
5. DOLBY SELECT Button
If you get background noise during PLAY, you can reduce this considerably by merely press- ing DOLBY SELECT button. If you want to release, press the button again.
CAUTION:
o Do not insert anything like coins into the player slot as damage to the unit may occur.
o Do not place beverages close to the audio system. The playback mecha- nism may be damaged if you spill them. o Do not impact on the audio system, or the playback mechanism could be dam- aged.
H260A01O-AAT STEREO RADIO OPERATION (H265) (If Installed)
3. BASS/TREBLE Control Knob
4. SCAN Button
6. BAND Selector
FEATURES OF YOUR HYUNDAI
83
7. PRESET Button
5. TUNE/SEEK Select Button
1. POWER ON-OFF/VOLUME/BALANCE Control Knob
2. FADER Control Knob
H260A01A
1FEATURES OF YOUR HYUNDAI
84
H260B05O-AAT 1. POWER ON-OFF Control Knob
The radio unit may be operated when the igni- tion key is in the "ACC" or "ON" position. Press the knob to switch the power on. The LCD shows the radio frequency in the radio mode or the CD track indicator in the CD mode. To switch the power off, press the knob again.
3. BASS Control Knob
Press to pop the knob out and turn to the left or right for the desired bass tone.
TREB (Treble Control) Knob
Pull the bass control knob further out. Turn to the left or right for the desired treble tone.
VOLUME Control
4. SCAN Button
When the scan button is pressed, the frequency will increase and the receivable stations will be tuned in one after another, receiving each sta- tion for 5 seconds. To stop scanning, press the scan button again.
5. TUNE (Manual) Select Button
Press the ( ) side or ( ) side to increase or to decrease the frequency. Press either button and hold down to continuously scroll. Release but- ton once the desired station is reached.
Rotate the knob clockwise to increase the vol- ume and turn the knob counterclockwise to reduce the volume.
BALANCE Control
Pull and turn the control knob clockwise to emphasize right speaker sound (left speaker sound will be attenuated). When the control knob is turned counterclockwise, left speaker sound will be emphasized (right speaker sound will be attenuated).
2. FAD (Fader Control) Knob
Turn the control knob counterclockwise to em- phasize front speaker sound (rear speaker sound will be attenuated). When the control knob is turned clockwise, rear speaker sound will be emphasized (front speaker sound will be attenuated).
SEEK Operation (Automatic Channel Selection)
Press the TUNE select button for 0.5 sec or
more. Releasing it will automatically tune to the
next available station with a beep sound.
When the ( ) side is pressed longer than 0.5
second, releasing will automatically tune to the
next higher frequency and when the ( ) side is
pressed longer than 0.5 second, releasing will
automatically tune to the next lower frequency.
6. BAND Selector
FM/AM
Pressing the button changes the AM, FM1
and FM2 bands. The mode selected is dis-
played on LCD.
7. PRESET STATION SELECT Button
Six (6) stations for AM, FM1 and FM2 respec- tively can be preset in the electronic memory circuit on this unit.
FEATURES OF YOUR HYUNDAI
85
CAUTION:
o Do not place beverages close to the audio system. The audio system mecha- nism may be damaged if you spill them. o Do not impact on the audio system, or the audio system mechanism could be damaged.
HOW TO PRESET STATIONS
Six AM and twelve FM stations may be pro- grammed into the memory of the radio. Then, by simply pressing the band select button and/or one of the six station select buttons, you may recall any of these stations instantly. To pro- gram the stations, follow these steps:
o Press band selector to set the band for AM,
FM1, or FM2.
o Select the desired station to be stored by
seek, scan or manual tuning.
o Determine the preset station select button
you wish to use to access that station.
o Press the station select button for more than two seconds. A select button indicator will show in the display indicating which select button you have depressed. The frequency display will flash after it has been stored into the memory. You should then release the button, and proceed to program the next desired station. A total of 18 stations can be programmed by selecting one AM and two FM stations per button.
o When completed, any preset station may be
recalled by selecting AM, FM1 or FM2
band and the appropriate station button.
1FEATURES OF YOUR HYUNDAI
86
H260B01O-AAT COMPACT DISC PLAYER OPERATION (H265) (If Installed)
4. SCAN Button
1. Playing CD
3. TRACK UP/DOWN
6. EJECT Button
2. FF/REW Button
5. REPEAT Button
H260A01A
B260D04O-AAT 1. Playing CD
o Insert the CD with the label facing upward. o Insert the CD to start CD playback, during
radio operation.
o When a disc is in the CD deck, if you press the CD button, the CD player will begin playing even if the radio is being used.
o The CD player can be used when the ignition switch is in either the "ON" or "ACC" posi- tion.
2. FF/REW ( / )
If you want to fast forward or reverse through the compact disc track, push and hold the FF ( ) or REW ( ) button. When you release the button, the compact disc player will resume playing.
3. TRACK UP/DOWN
o The desired track on the disc currently being played can be selected using the track num- ber.
o Press once to skip forward to the beginn- ing of the next track. Press once to skip back to the beginning of the track.
4. SCAN Button
o Press the SCAN button to playback the first
10 seconds of each track.
o Press the SCAN button again within 10 sec. when you have reached the desired track.
5. REPEAT Button
o To repeat the track you are currently listen- ing to, press the RPT button. To cancel, press again.
o If you do not release RPT operation when the track ends, it will automatically be re- played. This process will be continued until you push the button again.
6. EJECT Button
When the EJECT button is pressed with a CD loaded, the CD will eject.
FEATURES OF YOUR HYUNDAI
87
NOTE: o If the CD does not operate properly or if the ER2 fault code is displayed, use one of two methods to reset the CD deck function. - Remove the audio fuse for 5 minutes.
Then, reinstall the audio fuse.
- Diconnect the negative terminal of the battery and wait 5 minutes. Then, reconnect the negative battery termi- nal.
o To assure proper operation of the unit, keep the vehicle interior temperature within a normal range by using the vehicle's air conditioning or heating sys- tem.
o When replacing the fuse, replace it with
a fuse having the correct capacity.
o The preset station frequencies are all erased when the car battery is discon- nected. Therefore, all data will have to be set again if this should occur.
o Do not add any oil to the rotating parts. Keep magnets, screwdrivers and other metallic objects away from the tape mechanism and head.
o This equipment is designed to be used only in a 12 volt DC battery system with negative ground.
!
CAUTION:
o Do not grip or pull out the disc with your hand while the disc is being pulled into the unit by the self loading mecha- nism. These can cause poor disc scratching to occur or trouble in the compact disc player.
o Avoid using CD-Recordable or CD- Rewritable as the player could not be operated in recording way of the CD maker. When using the compact disc player, genuine CDs are recommended.
1FEATURES OF YOUR HYUNDAI
88
o This unit is made of precision parts. Do not attempt to disassemble or adjust any parts.
o When driving your vehicle, be sure to keep the volume of the unit set low enough to allow you to hear sounds coming from the outside.
o Do not expose this equipment (includ- ing the speakers) to water or excessive moisture.
CAUTION:
o Do not insert warped or poor quality discs into the CD player as damage to the unit may occur.
o Do not insert anything like coins into the player slot as damage to the unit may occur.
o Do not place beverages close to the audio system. The playback mecha- nism may be damaged if you spill them. o Do not impact on the audio system, or the playback mechanism could be dam- aged.
o Driving on the off-roads or other vibra-
tions may skip your compact disc. Do not use the audio system on off- roads as the discs could be scratched and damaged.
FEATURES OF YOUR HYUNDAI
89
B890A01A-AAT AUDIO FAULT CODE
If you see any error indication in the display while using the system in CD or Tape mode, find the cause in the chart below. If you cannot clear the error indication, take the car to your Hyundai dealer.
INDICATION
CAUSE
SOLUTION
Er2
Er3
Er6
Er8
CD DECK MECHANICAL ERROR (EJECT ERROR, LOADING ERROR)
After resetting the audio system, push the eject button. If disc is not ejected, consult your Hyundai dealer.
FOCUS ERROR DATA READ ERROR
DISC ERROR
Make sure the disc is not scratched or damaged. Press the eject button and pull out the disc. Then insert a normal CD disc.
Check if the disc is inserted correctly in the CD player. Make sure the disc is not scratched or damaged.
TAPE DECK ERROR TAPE EJECT ERROR
After resetting the audio system, push the eject button. If tape does not eject, consult your Hyundai dealer.
1FEATURES OF YOUR HYUNDAI
90
CARE OF DISC
B850A02F-AAT Proper Handling
CARE OF CASSETTE TAPES
Storage
B860A01A-AAT
When not in use, place your discs in their individual case and store them in a cool place away from the sun, heat, and dust. Do not grip or pull out the disc with your hand while the disc is being pulled into the unit by the Self Loading mechanism.
Keep Your Discs Clean
B850A01L
Handle your disc as shown. Do not drop the disc. Hold the disc so you will not leave fingerprints on the surface. If the surface is scratched, it may cause the pickup to skip signal tracks. Do not affix tape, paper, or gummed labels on the disc. Do not write on the disc.
Damaged Disc
Do not attempt to play damaged, warped or cracked discs. It could severely damage the playback mechanism.
B850A02L
Fingerprints, dust, or soil on the surface could cause the pickup to skip signal tracks. Wipe the surface clean with a clean soft cloth. If the surface is heavily soiled, dampen a clean soft cloth in a solution of mild neutral detergent to wipe it clean. See drawing.
B860A01L
Proper care of your cassette tapes will extend the tape life and increase your listening enjoy- ment. Always protect your tapes and cassette cases from direct sunlight, severely cold and dusty conditions. When not in use, cassettes should always be stored in the protective cas- sette case in which they were originally sup- plied. When the vehicle is very hot or cold, allow the interior temperature to become more com- fortable before listening to your cassettes.
o Keep all magnetized objects, such as elec- tric motors, speakers or transformers away from your cassette tapes and tape player unit.
o Store cassettes in a cool, dry place with the open side facing down to prevent dust from settling in the cassette body.
o Avoid repeated fast reverse usage to re- play one given tune or tape section. This can cause poor tape winding to occur, and eventually cause excessive internal drag and poor audio quality in the cassette. If this occurs, it can sometimes be corrected by fast winding the tape from end to end several times. If this does not correct the problem, do not continue to use the tape in your vehicle.
o Never leave a cassette inserted in the player when not being played. This could damage the tape player unit and the cas- sette tape.
o We strongly recommend against the use of tapes longer than C-60 (60 minutes total). Tapes such as C-120 or C-180 are very thin and do not perform as well in the automotive environment.
HLC216
o Be sure that the cassette label is not loose or peeling off or tape ejection may be difficult.
o Never touch or soil the actual audio tape
surfaces.
FEATURES OF YOUR HYUNDAI
91
Head
Cotton applicator
B860A02L o The playback head, capstan and pinch rollers will develop a coating of tape residue that can result in deterioration of sound quality, such as a wavering sound. They should be cleaned monthly using a com- mercially available head cleaning tape or special solution available from audio spe- cialty shops. Follow the supplier's direc- tions carefully and never oil any part of the tape player unit.
o Always be sure that the tape is tightly wound on its reel before inserting in the player. Rotate a pencil in the drive sprock- ets to wind up any slack.
1FEATURES OF YOUR HYUNDAI
92
ANTENNA
B870A01A-AAT Fixed Rod Antenna
B870B01Y-AAT Power Antenna (If Installed)
B860A03L
NOTE: Look at a tape before you insert it. If the tape is loose, tighten it by turning one of the hubs with a pencil or your finger. If the label is peeling off, do not put it in the player. It may cause the tape to jam in the drive mechanism when you try to eject it. Do not leave tape sitting where they are exposed to high temperatures or, high hu- midity, such as on top of the dashboard or in the player. If a tape is excessively hot or cold, let it reach a moderate temperature before putting it in the player.
B870A01A Your car uses a fixed rod antenna to receive both AM and FM broadcast signals. This antenna is a removable type. To remove the antenna, turn it counterclockwise. To install the antenna, turn it clockwise.
CAUTION:
o Be sure to remove the antenna before washing the car in an automatic car wash or it may be damaged.
o When reinstalling your antenna, it is im- portant that it is fully tightened to ensure proper reception.
HLC2123
The antenna will automatically be extended when the radio power switch is turned on while the ignition key is in either the "ON" or "ACC" position. The antenna will automatically be re- tracted and stored when either the radio power switch is turned off or the ignition key is set to the "LOCK" position.
NOTE: o Before turning on the radio, make sure
that no one is near the antenna.
o Before entering an automatic car wash or a place with a low height clearance, be sure that the antenna is retracted and stored.
o If the antenna is dirty, be sure to clean it in order to avoid an operation malfunc- tion.
FEATURES OF YOUR HYUNDAI
93
DRIVING YOUR HYUNDAI
Before Starting the Engine ............................................ 2-3
Key Positions ................................................................ 2-3
Starting .......................................................................... 2-4
Operating the Manual Transaxle ................................... 2-5
Automatic Transaxle ..................................................... 2-7
Good Braking Practices .............................................. 2-10
Anti-Lock Brake System ............................................. 2-11
Driving for Economy ................................................... 2-12
Winter Driving ............................................................. 2-13
Trailer Towing ............................................................. 2-19
2 DRIVING YOUR HYUNDAI
WARNING: ENGINE EXHAUST CAN BE DANGEROUS!
C010A03A-AAT Engine exhaust fumes can be extremely dangerous. If, at any time, you smell exhaust fumes inside the vehicle, open the windows immediately. o Do not inhale exhaust fumes. Exhaust fumes contain carbon monoxide, a colorless, odorless gas that can cause unconsciousness and death by asphyxiation. o Be sure the exhaust system does not leak. The exhaust system should be checked whenever the vehicle is raised to change the oil or for any other purpose. If you hear a change in the sound of the exhaust or if you drive over something that strikes the underneath side of the car, have the exhaust system checked as soon as possible by your Hyundai dealer. o Do not run the engine in an enclosed area. Letting the engine idle in your garage, even with the garage door open, is a hazardous practice. Never run the engine in your garage any longer than it takes to start the engine and back the car out. o Avoid idling the engine for prolonged periods with people inside the car. If it is necessary to idle the engine for a prolonged period with people inside the car, be sure to do so only in an open area with the air intake set at "Fresh" and fan operating at one of the higher speeds so fresh air is drawn into the interior. If you must drive with the trunk lid/ tail gate open because you are carrying objects that make this necessary: 1. Close all windows. 2. Open side vents. 3. Set the air intake control at "Fresh", the air flow control at "Floor" or "Face" and the fan at one of the higher speeds. To assure proper operation of the ventilation system, be sure the ventilation air intakes located just in front of the windshield are kept clear of snow, ice, leaves or other obstructions.
PROPOSITION 65 WARNING:
Engine exhaust and a wide variety of automobile components and parts, including components found in the interior furnishings in a vehicle, contain or emit chemicals known to the State of California to cause cancer and birth defects and reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
BEFORE STARTING THE ENGINE
TO START THE ENGINE
KEY POSITIONS
DRIVING YOUR HYUNDAI
C020A01A-AAT Before you start the engine, you should al- ways:
1. Look around the vehicle to be sure there are no flat tires, puddles of oil or water or other indications of possible trouble.
2. After entering the car, check to be sure the
parking brake is engaged.
3. Check that all windows, and lights are clean. 4. Check that the interior and exterior mirrors
are clean and in position.
5. Check your seat, seatback and headrest to
be sure they are in their proper positions.
6. Lock all the doors. 7. Fasten your seat belt and be sure that all
other occupants have fastened theirs.
8. Turn off all lights and accessories that are
not needed.
9. When you turn the ignition switch to "ON", check that all appropriate warning lights are operating and that you have sufficient fuel. 10.Check the operation of warning lights and all
bulbs when key is in the "ON" position.
C030A01A-AAT COMBINATION IGNITION SWITCH
C040A01A-AAT
o If your Hyundai is equipped with a manual transaxle, place the shift lever in neutral and depress the clutch pedal fully.
o If your Hyundai has an automatic transaxle,
place the shift lever in "P" (park).
o To start the engine, insert the ignition key and turn it to the "START" position. Release it as soon as the engine starts. Do not hold the key in the "START" position for more than 15 seconds.
NOTE: o For safety, the engine will not start if the clutch pedal is not depressed fully (Manual Transaxle) or the shift lever is not in "P" or "N" Position (Automatic Transaxle).
o The ignition key cannot be turned from "ACC" position to "LOCK" position un- less the shift lever is in the "P" (Park) position or the negative battery terminal is disconnected from the battery. (For Automatic Transaxle)
LOCK
ACC
ON
START
C040A01A-1
WARNING:
The engine should not be turned off or the key removed from the ignition key cylinder while the vehicle is in motion. The steering wheel is locked by removing the key.
o "START"
The engine is started in this position. It will crank until you release the key.
NOTE: Do not hold the key in the "START" posi- tion for more than 15 seconds.
2 DRIVING YOUR HYUNDAI
o "ON"
When the key is in the "ON" position, the ignition is on and all accessories may be turned on. If the engine is not running, the key should not be left in the "ON" position. This will discharge the battery and may also damage the ignition system.
o "ACC"
With the key in the "ACC" position, some elec- trical accessories (radio, etc.) may be operat- ed.
o "LOCK"
The key can be removed or inserted in this position. To protect against theft, the steering wheel locks by removing the key.
NOTE: To unlock the steering wheel, insert the key, and then turn the steering wheel and key simultaneously.
C070C01A-AAT To Remove the Ignition Key
ACC
LOCK
ON
STARTING
C050A01A-AAT
LOCK
START
C070C01A-1
ON
START
C050A01A-1
1. Turn the ignition key to the "ACC" position. 2. Simultaneously push and turn the ignition key counterclockwise from the "ACC" posi- tion to the "LOCK" position.
3. The key can be removed in the "LOCK"
position.
WARNING:
Never run the engine in a closed or poorly ventilated area any longer than is needed to move your car in or out of the area. The carbon monoxide gas emitted is odorless and can cause serious injury or death.
C050B01A-AAT Normal Conditions:
The Starting Procedure:
Insert key, and fasten the seat belt.
1. 2. Depress the clutch pedal fully and place the gearshift lever (manual transaxle) in neutral or the selector lever (automatic transaxle) in "P" (park) position.
3. After turning the ignition key to the "ON" position, make certain all warning lights and gauges are functioning properly before start- ing the engine.
WARNING:
Be sure that the clutch is fully depressed when starting a manual transaxle vehicle. Your manual transaxle equipped vehicle will not start unless the clutch pedal is fully depressed. On a manual transaxle equipped vehicle that can be started without depress- ing the clutch, there is the potential to cause damage to the vehicle or injury to someone inside or outside the vehicle as a result of the forward or backward movement of the vehicle that will occur if the clutch is not depressed when the vehicle is started.
DRIVING YOUR HYUNDAI
OPERATING THE MANUAL TRANSAXLE
C070A02A-AAT
4. Turn the ignition key to the "Start" position
and release it when the engine starts. After the engine has started, allow the engine to run for 10 to 20 seconds prior to placing the vehicle in gear. The starter should not be operated for more than 15 seconds at a time. Wait 15-30 sec- onds between starting attempts to protect the starter from overheating.
C070A01A
Your Hyundai's manual transaxle has a con- ventional shift pattern. This shift pattern is also imprinted on the shift knob. The transaxle is fully synchronized in all forward gears so shifting to either a higher or a lower gear is easily accomplished.
NOTE: o To shift into reverse, rest the lever in neutral for at least 3 seconds after your car is completely stopped. Then move the lever into the reverse position.
o During cold weather, shifting may be difficult until the transaxle lubricant has warmed up. This is normal and not harmful to the transaxle.
2 DRIVING YOUR HYUNDAI
o If you've come to a complete stop and it's hard to shift into 1st or R(Reverse), put the shift lever in N(Neutral) position and release the clutch. Press the clutch pedal back down, and then shift into 1st or R(Reverse) gear position.
o Do not use the shift lever as a handrest during driving, as this can result in pre- mature wear of the transaxle shift forks.
CAUTION:
When downshifting from fifth gear to fourth gear, caution should be taken not to inadvertently press the gear shift lever sideways in such a manner that second gear is engaged. Such a drastic downshift may cause the engine speed to increase to the point that the tachometer will enter the red zone. Such over revving of the engine may possibly cause engine damage.
C070B01A-AAT Using the Clutch
C070D02O-AAT Good Driving Practices
The clutch should be pressed all the way to the floor before shifting, then released slowly. Do not rest your foot on the clutch pedal while driving. This can cause unnecessary wear. Do not partially engage the clutch to hold the car on an incline. This causes unnecessary wear. Use the parking brake to hold the car on an incline. Do not operate the clutch pedal rapidly and repeatedly.
C070E03A-AAT RECOMMENDED SHIFT POINTS
Shift
from-to
1-2
2-3
3-4
4-5
Recommended
mph(km/h)
15 (20)
25 (40)
35 (55)
45 (75)
The shift points as shown above are recom- mended for optimum fuel economy and perform- ance.
o Never take the car out of gear and coast down a hill. This is extremely hazardous. Always leave the car in gear.
o Don't "ride" the brakes. This can cause them to overheat and malfunction. Instead, when you are driving down a long hill, slow down and shift to a lower gear. When you do this, engine braking will help slow the car.
o Slow down before shifting to a lower gear. This will help avoid over-revving the engine, which can cause damage.
o Slow down when you encounter cross winds. This gives you much better control of your car.
o Be sure the car is completely stopped before you attempt to shift into reverse. The transaxle can be damaged if you do not. To shift into reverse, depress the clutch, move the shift lever to neutral, wait three seconds, then shift to the reverse position.
o Exercise extreme caution when driving on a slippery surface. Be especially careful when braking, accelerating or shifting gears. On a slippery surface, an abrupt change in vehicle speed can cause the drive wheels to lose traction and the vehicle to go out of control.
!
WARNING:
o Avoid high cornering speeds. o Do not make quick steering wheel move- ments, such as sharp lane changes or fast, sharp turns.
o Always wear your seat belts.
In a collision crash, un unbelted person is significantly more likely to die than a person wearing a seatbelt.
o The risk of rollover is greatly increased if you lose control of your vehicle at highway speeds.
o Loss of control often occurs if two or more wheels drop off the roadway and the driver oversteers to reenter the road- way.
o In the event your vehicle leaves the roadway, do not steer sharply. Instead, slow down before pulling back into the travel lanes.
o Never exceed posted speed limits.
AUTOMATIC TRANSAXLE
C090A01A-AAT
DRIVING YOUR HYUNDAI
NOTE:
Depress the brake pedal and push the button when shifting
Push the button when shifting The selector lever can be shifted freely.
For optimum fuel economy, accelerate gradu- ally. The transaxle will automatically shift to the second, third and overdrive gears.
C090A01A The highly efficient Hyundai automatic transaxle has four forward speeds and one reverse speed. It has a conventional shift pattern as shown in the illustration. At night, with the multi-function switch turned on to the parking light or head light position the appro- priate symbol on the shift pattern indicator will be illuminated according to the range selected.
C090B02A-AAT The function of each position is as fol- lows:
o P (Park):
Use to hold the vehicle in place when parking or while starting the engine. Whenever parking the car, apply the parking brake and shift the selector lever to the "P" (Park) position.
CAUTION:
Never shift into "R" or "P" position while the car is moving.
CAUTION:
Never place the selector lever in the "P" (Park) position unless the vehicle is fully stopped. Failure to observe this caution will cause severe damage to the transaxle.
2 DRIVING YOUR HYUNDAI
C090C01A-AAT o R(Reverse):
Use for backing up the vehicle. Bring the car to a complete stop before shifting the selector lever to "R" position.
C090D02A-AAT o N (Neutral):
In the "N" position, the transaxle is in neutral position, which means that no gears are en- gaged. The engine can be started with the shift lever in "N" position, although this is not recom- mended except if the engine stalls while the car is moving.
C090E01A-AAT o D (Drive):
Use for normal driving. The transaxle will auto-
matically shift through a four-gear sequence.
Never downshift manually to "2" position or "L"
position when vehicle speed is more than 60
mph (96 km/h).
C090F01A-AAT o 2 (Second gear):
Use for driving on a slippery road, hill climbing or engine braking downhill. "2" automatically shifts between first and second gears. This means that no shift-up to 3rd gear is per- formed. However, the shift-up to third gear is done when the car speed exceeds a certain value to prevent the engine from over-revving. Manually move the selector to "D" returning to normal driving condition.
C090G01A-AAT o L (Low gear):
Use for driving up a very steep grade or for engine braking when descending steep hills. When downshifting to "L", the transaxle will temporarily remain in second gear until the ve- hicle has slowed enough for low gear to engage. Do not exceed 31 mph (50 km/h) in low gear.
C090H01A-AAT NOTE: o For smooth and safe operation, de- press the brake pedal when shifting from "Neutral" position or "Park" posi- tion to a forward or reverse gear.
o The ignition key must be in the "ON" position and the brake pedal fully de- pressed in order to move the shift lever from the "P" (Park) position to any of the other positions.
o It is always possible to shift from "R", "N", "D", "2", "L" position to "P" posi- tion.
C090I01A-AAT
CAUTION:
o Shift into "R" and "P" position only when the vehicle has completely stopped.
o Do not accelerate the engine in reverse or any of the forward positions with the brakes applied.
o Always apply the footbrake when shifting from "P" or "N", to "R", "D", "2" or "L" position.
o Do not use the "P" (Park) position in place of the parking brake. Always set the parking brake, shift the transaxle into "P" (Park) position and turn off the igni- tion when you leave the vehicle, even momentarily. Never leave the vehicle un- attended while the engine is running.
o Check the automatic transaxle fluid level
regularly, and add fluid as necessary.
C090P01A-AAT Overdrive Switch
JC110J4-A SHIFT LOCK RELEASE (If Installed)
DRIVING YOUR HYUNDAI
C090P01A
C090J01A
When the overdrive switch is turned on, the transaxle will automatically upshift to the sec- ond, third and overdrive gears. When the over- drive switch is turned off, the transaxle will not upshift to the overdrive gear. For normal driving, the selector lever should be left in the "D" position and the overdrive switch turned on. If you need to accelerate rapidly, press the accelerator pedal all the way to the floor. The transaxle will automatically shift to a lower gear, depending on the vehicle speed and load.
If you cannot move the shift lever from the "P" (Park) position to any other position with the brake pedal fully depressed and the ignition key in the "ON" position, remove the cap on the console with a thin object such as a pencil, push the shift lock release button down. Then, with the brake pedal depressed, move the shift lever to the desired position, then the shift lock re- lease button will automatically return to its origi- nal position after shifting from the "P" (Park) position. Then, reinstall the cap. Have the system checked by your Hyundai dealer.
2 DRIVING YOUR HYUNDAI
10
C090N03A-AAT Good Driving Practices
o Never move the gear selector lever from "P" or "N" to any other position with the acceler- ator pedal depressed.
o Never move the gear selector lever into "P"
when the vehicle is in motion.
o Be sure the car is completely stopped before
you attempt to shift into "R".
o Never take the car out of gear and coast down a hill. This may be extremely hazard- ous. Always leave the car in gear when moving.
o Do not "ride" the brakes. This can cause them to overheat and malfunction. Instead, when you are driving down a long hill, slow down and shift to a lower gear. When you do this, engine braking will help slow the car.
o Slow down before shifting to a lower gear. Otherwise, the lower gear may not be en- gaged.
o Always use the parking brake. Do not de- pend on placing the transaxle in "P" to keep the car from moving.
o Exercise extreme caution when driving on a slippery surface. Be especially careful when braking, accelerating or shifting gears. On a slippery surface, an abrupt change in vehicle speed can cause the drive wheels to lose traction and the vehicle to go out of control.
o Turn the overdrive switch on for good fuel economy and smooth driving. If engine brak- ing is needed in the "D" range or if repeated upshifting and downshifting between the 3rd and 4th gear is needed when climbing a gentle slope, it is recommended that the overdrive switch be turned off. Turn the over- drive switch back on immediately afterward.
WARNING:
o Avoid high cornering speeds. o Do not make quick steering wheel move- ments, such as sharp lane changes or fast, sharp turns.
o Always wear your seat belts.
In a collision crash, un unbelted person is significantly more likely to die than a person wearing a seatbelt.
o The risk of rollover is greatly increased if you lose control of your vehicle at highway speeds.
o Loss of control often occurs if two or more wheels drop off the roadway and the driver oversteers to reenter the road- way.
o In the event your vehicle leaves the roadway, do not steer sharply. Instead, slow down before pulling back into the travel lanes.
o Never exceed posted speed limits.
GOOD BRAKING PRACTICES
C130A01A-AAT
WARNING:
Nothing should be carried on top of the shelf panel behind the rear seat. If there were an accident or a sudden stop, such objects could move forward and cause damage to the vehicle or injure the occu- pants.
o After being parked, check to be sure the parking brake is not engaged and that the parking brake indicator light is out before driving away.
o Driving through water may get the brakes wet. They can also get wet when the car is washed. Wet brakes can be dangerous! Your car will not stop as quickly if the brakes are wet. Wet brakes may cause the car to pull to one side. To dry the brakes, apply the brakes lightly until the braking action returns to nor- mal, taking care to keep the car under con- trol at all times. If the braking action does not return to normal, stop as soon as it is safe to do so and call your Hyundai dealer for assis- tance.
o Don't coast down hills with the car out of gear. This is extremely hazardous. Keep the car in gear at all times, use the brakes to slow down, then shift to a lower gear so
o Under some conditions your parking brake can freeze in the engaged position. This is most likely to happen when there is an accumulation of snow or ice around or near the rear brakes or if the brakes are wet. If there is a risk that the parking brake may freeze, apply it only temporarily while you put the gear selector lever in "P" (automat- ic) or in first or reverse gear (manual transaxle) and block the rear wheels so the car cannot roll. Then release the parking brake.
o Do not hold the vehicle on the upgrade with the accelerator pedal. This can cause the transaxle to overheat. Always use the brake pedal or parking brake.
DRIVING YOUR HYUNDAI
ANTI-LOCK BRAKE SYSTEM
11
C120A02A-AAT (If Installed)
The Anti-Lock Brake System (ABS) is de- signed to prevent wheel lock-up during sud- den braking or on hazardous road surfaces. The ABS control module monitors the wheel speed and controls the pressure applied to each brake. Thus, in emergency situations or on slick roads, ABS will increase vehicle con- trol during braking.
NOTE: During ABS operation, a slight pulsation may be felt in the brake pedal when the brakes are applied. Also, a noise may be heard in the engine compartment while brak- ing. These conditions are normal and indi- cate that the anti-lock brake system is func- tioning properly.
that engine braking will help you maintain a safe speed.
o Don't "ride" the brake pedal. Resting your foot on the brake pedal while driving can be dangerous because it can result in the brakes overheating and losing their effectiveness. It also increases the wear of the brake compo- nents.
o If a tire goes flat while you are driving, apply the brakes gently and keep the car pointed straight ahead while you slow down. When you are moving slowly enough for it to be safe to do so, pull off the road and stop in a safe place.
o If your car is equipped with an automatic transaxle, don't let your car creep forward. To avoid creeping forward, keep your foot firmly on the brake pedal when the car is stopped.
o Use caution when parking on a hill. Engage the parking brake and place the gear selec- tor lever in "P" (automatic transaxle) or in first or reverse gear (manual transaxle). If your car is facing downhill, turn the front wheels into the curb to help keep the car from rolling. If your car is facing uphill, turn the front wheels away from the curb to help keep the car from rolling. If there is no curb or if it is required by other conditions to keep the car from rolling, block the wheels.
2 DRIVING YOUR HYUNDAI
12
WARNING:
ABS will not prevent accidents due to improper or dangerous driving maneu- vers. Even though vehicle control is im- proved during emergency braking, always maintain a safe distance between you and objects ahead. Vehicle speeds should al- ways be reduced during extreme road conditions. The braking distance for cars equipped with an anti-lock braking system may be longer than for those without it in the following road conditions. During these conditions the veicle should be driven at reduced speeds.
o Rough, gravel or snow-covered roads. o With tire chains installed. o On roads where the road surface is pitted or has different surface height.
These roads should be driven at reduced speeds. The safety features of an ABS equipped vehicle should not be tested by high speed driving or cornering. This could endanger the safety of yourself or others.
DRIVING FOR ECONOMY
C140A01A-AAT You can save fuel and get more miles from your car if you follow these suggestions:
o Drive smoothly. Accelerate at a moderate rate. Don't make "jack-rabbit" starts or full- throttle shifts and maintain a steady cruising speed. Don't race between stoplights. Try to adjust your speed to that of the other traffic so you don't have to change speeds unnec- essarily. Avoid heavy traffic whenever possi- ble. Always maintain a safe distance from other vehicles so you can avoid unneces- sary braking. This also reduces brake wear. o Drive at a moderate speed. The faster you drive, the more fuel your car uses. Driving at a moderate speed, especially on the high- way, is one of the most effective ways to reduce fuel consumption.
o Don't "ride" the brake or clutch pedal. This can increase fuel consumption and also in- crease wear on these components. In addi- tion, driving with your foot resting on the brake pedal may cause the brakes to over- heat, which reduces their effectiveness and may lead to more serious consequences.
o Take care of your tires. Keep them inflated to the recommended pressure. Incorrect infla- tion, either too much or too little, results in unnecessary tire wear. Check the tire pres- sures at least once a month.
o Be sure that the wheels are aligned cor- rectly. Improper alignment can result from hitting curbs or driving too fast over irreg- ular surfaces. Poor alignment causes faster tire wear and may also result in other problems as well as greater fuel consump- tion.
o Keep your car in good condition. For better fuel economy and reduced maintenance costs, maintain your car in accordance with the maintenance schedule in Section 5. If you drive your car in severe conditions, more frequent maintenance is required (see Sec- tion 5 for details).
o Keep your car clean. For maximum service, your Hyundai should be kept clean and free of corrosive materials. It is especially impor- tant that mud, dirt, ice, etc. not be allowed to accumulate on the underside of the car. This extra weight can result in increased fuel consumption and also contribute to corro- sion.
o Travel lightly. Don't carry unnecessary weight in your car. Weight reduces fuel economy. o Don't let the engine idle longer than neces- sary. If you are waiting (and not in traffic), turn off your engine and restart only when you're ready to go.
o Remember, your Hyundai does not require extended warm-up. As soon as the engine is running smoothly, you can drive away. In very cold weather, however, give your en- gine a slightly longer warm-up period.
o Don't "lug" or "over-rev" the engine. Lug- ging is driving too slowly in too high a gear resulting in the engine bucking. If this hap- pens, shift to a lower gear. Over-revving is racing the engine beyond its safe limit. This can be avoided by shifting at the recom- mended speeds.
o Use your air conditioning sparingly. The air conditioning system is operated by engine power so your fuel economy is reduced when you use it.
SMOOTH CORNERING
WINTER DRIVING
DRIVING YOUR HYUNDAI
13
C150A01A-AAT Avoid braking or gear changing in corners, especially when roads are wet. Ideally, cor- ners should always be taken under gentle acceleration. If you follow these suggestions, tire wear will be held to a minimum.
C160A01A-AAT The more severe weather conditions of winter result in greater wear and other problems. To minimize the problems of winter driving, you should follow these suggestions:
C160B01A-AAT Snowy or Icy Conditions
To drive your vehicle in deep snow, it may be necessary to use snow tires or to install tire chains on your tires. If snow tires are needed, it is necessary to select tires equivalent in size and type to the original equipment tires. Failure to do so may adversely affect the safety and handling of your car. Furthermore, speeding, rapid acceleration, sudden brake applications, and sharp turns are potentially very hazardous practices. During deceleration, use engine braking to the fullest extent. Sudden brake applications on snowy or icy roads may cause skids to occur. You need to keep sufficient distance between the vehicle in operation in front and your vehicle. Also, apply the brake gently. It should be noted that installing tire chains on the tire will provide a greater driving force, but will not prevent side skids.
NOTE: Tire chains are not legal in all states. Check state laws before fitting tire chains.
2 DRIVING YOUR HYUNDAI
14
C160C01A-AAT Use High Quality Ethylene Glycol Coolant
C160E01A-AAT Change to "Winter Weight" Oil if Necessary
Your Hyundai is delivered with high quality eth- ylene glycol coolant in the cooling system. It is the only type of coolant that should be used because it helps prevent corrosion in the cooling system, lubricates the water pump and prevents freezing. Be sure to replace or replenish your coolant in accordance with the maintenance schedule in Section 5. Before winter, have your coolant tested to assure that its freezing point is sufficient for the temperatures anticipated dur- ing the winter.
C160D01A-AAT Check Battery and Cables
Winter puts additional burdens on the battery system. Visually inspect the battery and cables as described in Section 6. The level of charge in your battery can be checked by your Hyundai dealer or a service station.
In some climates it is recommended that a lower viscosity "winter weight" oil be used during cold weather. See Section 9 for recommendations. If you aren't sure what weight oil you should use, consult your Hyundai dealer.
C160F01A-AAT Check Spark Plugs and Ignition System
Inspect your spark plugs as described in Sec- tion 6 and replace them if necessary. Also check all ignition wiring and components to be sure they are not cracked, worn or damaged in any way.
C160G01A-AAT To Keep Locks from Freezing
To keep the locks from freezing, squirt an ap- proved de-icer fluid or glycerine into the key opening. If a lock is covered with ice, squirt it with an approved de-icing fluid to remove the ice. If the lock is frozen internally, you may be able to thaw it out by using a heated key. Handle the heated key with care to avoid injury.
C160H01A-AAT Use Approved Anti-Freeze in Window Washer System
To keep the water in the window washer system from freezing, add an approved anti-freeze so- lution in accordance with instructions on the container. Window washer anti-freeze is avail- able from Hyundai dealers and most auto parts outlets. Do not use engine coolant or other types of anti-freeze as these may damage the finish.
DRIVING YOUR HYUNDAI
HIGHER SPEED MOTORING
15
C160I01A-AAT Don't Let Your Parking Brake Freeze
C160K01A-AAT Carry Emergency Equipment
C170A01A-AAT Pre-Trip Inspections
Under some conditions your parking brake can freeze in the engaged position. This is most likely to happen when there is an accumulation of snow or ice around or near the rear brakes or if the brakes are wet. If you think the parking brake may freeze, apply it only temporarily while you put the gear selector lever in "P" (automatic) or in first or reverse gear (manual transaxle) and block the rear wheels so the car cannot roll. Then release the parking brake.
C160J01A-AAT Don't Let Ice and Snow Accumulate Underneath
Under some conditions, snow and ice can build up under the fenders and interfere with the steering. When driving in severe winter condi- tions where this may happen, you should peri- odically check underneath the car to be sure the movement of the front wheels and the steering components is not obstructed.
Depending on the severity of the weather where you drive your car, you should carry appropriate emergency equipment. Some of the items you may want to carry include tire chains, tow straps or chains, flashlight, emergency flares, sand, a shovel, jumper cables, a window scraper, gloves, ground cloth, coveralls, a blanket, etc.
1. Tires: Adjust the tire inflation pressures for highway driving. Low tire inflation pressures will result in overheating and possible failure of the tires. Avoid using worn or damaged tires which may result in reduced traction or tire failure.
NOTE: Never exceed the maximum tire inflation pres- sure shown on the tires.
2. Fuel, engine coolant and engine oil: High speed travel consumes more fuel than urban motoring. Do not forget to check both engine coolant and engine oil.
3. Drive belt: A loose or damaged drive belt may result in overheating of the engine.
2 DRIVING YOUR HYUNDAI
USE OF LIGHTS
16
C180A01A-AAT Check your lights regularly for correct opera- tion and always keep them clean. When driv- ing during the day in conditions of poor visibil- ity, it is helpful to drive with headlights on low beam. This enables you to be seen as well as to see.
TRAILER TOWING
C190A01A-AAT
C190A02A
Your Hyundai should not be used to tow a trailer. It is designed to be compact and light for good fuel economy, and is not designed as a trailer-towing vehicle. Damages or malfunc- tions caused by towing may not be covered by the limited warranties applying to your Hyundai. Damages or malfunctions that result from tow- ing a trailer for commercial purposes are specifi- cally not covered by Hyundai limited warranties.
WHAT TO DO IN AN EMERGENCY
If the Engine Will Not Start .......................................... 3-2
Jump Starting ............................................................... 3-3
If the Engine Overheats............................................... 3-4
Spare Tire ..................................................................... 3-5
If You Have a Flat Tire ................................................ 3-6
Changing a Flat Tire .................................................... 3-6
If Your Car Must Be Towed ...................................... 3-11
Emergency Towing..................................................... 3-12
If You Lose Your Keys .............................................. 3-13
3 3
3
WHAT TO DO IN AN EMERGENCY
IF THE ENGINE WILL NOT START
D010A01A-AAT
WARNING:
If the engine will not start, do not push or pull the car to start it. This could result in a collision or cause other damage. In addition, push or pull starting may cause the catalytic converter to be overloaded and create a fire hazard.
D010B02A-AAT If Engine Doesn't Turn Over or Turns Over Slowly
D010C01A-AAT If Engine Turns Over Normally but Does Not Start