Login- Download PDF Manual
-
Storage Compartments
Glove Box Open the glove box by pulling up on the bottom of the handle.
Cupholders The vehicle may have cupholders in front of the front armrest storage area and in the lower area of the driver and front passenger doors. The H3 may also have a cupholder in the center of the rear bench seat. Pull down on the cover to open the cupholder. The H3T may have cupholders in the rear seat and cup/bottle holders located on the bottom of the rear doors.
4-2
Storage
Additional Storage Features
Rear Compartment/ Storage Panel Cover The H3 has a rear storage area located on the passenger side of the cargo area. To open it, pull the two tabs out and open lid.
Cargo Cover Notice: Do not put items onto the cargo cover. The weight of the items could cause the attachment clips to break. The cargo cover could no longer be attached and used. The repairs would not be covered by the warranty. Never put anything on top of the cargo cover.
Cargo Management System The vehicle comes with a cargo management system located in the bed of the vehicle. The system contains three rails located on the front and sides of the bed.
The vehicle may have a cargo cover. It can be used to cover items in the rear of the vehicle. To install the cover, place the loops on each corner of the cover on the four hooks in the rear of the vehicle. The cover should be stored securely when not in use.
Cargo Tie Downs There may be four cargo tie-downs that can be moved on the tracks located on the roof. To move, loosen the tie-down counterclockwise. Turn clockwise to tighten and lock in place.
The system has four adjustable cargo tie-downs, that can be placed on the upper and lower slides of the rail.
Storage
4-3
To remove or install cargo tie-downs at the front of the bed, slide the corner cap towards the center of the bed to expose the rail notches. To remove the corner cap, pull either edge away from the rail. To remove the system, loosen the toggle bolts on each rail until they can be removed from the bed of the truck. To replace the system, place the toggle bolts and rails into their original locations and tighten them to a torque setting of 17Y (12.5 ft‐lbs).
Notice: If cargo is tied down using the horizontal slots on the top of the pickup box, the box could be damaged and would not be covered by the vehicle warranty. Only use the tie-down loops if the vehicle does not have the cargo management system.
Convenience Net Use the convenience net, located in the rear, to store small loads as far forward as possible. The net should not be used to store heavy loads.
To adjust a tie-down, pull the locator pin out and move the tie-down to another location making sure the locator pin lines up with a locator hole on the rail. The tie-down pin may not be installed correctly if the pin does not line up, turn it over and reinstall. The tie-down will not move when the pin is completely installed. The maximum load for each rail is 227 kg (500 lbs). The rails are notched at each end which allows the tie-downs to be removed and placed on another rail. To remove, pull the locator pin out and slide the tie-down to the end of the rail and pull back.
4-4
Storage
Roof Rack System
{ WARNING
If something is carried on top of the vehicle that is longer or wider than the roof rack— like paneling, plywood, or a mattress— the wind can catch it while the vehicle is being driven. The item being carried could be violently torn off, and this could cause a collision, and damage the vehicle. Never carry something longer or wider than the roof rack on top of the vehicle unless using a HUMMER Certified accessory carrier.
For vehicles with a roof rack, the rack can be used to load items. For roof racks that do not have crossrails included, HUMMER Certified crossrails can be purchased as an accessory. See your dealer for additional information. Notice: Loading cargo on the roof rack that weighs more than 113 kg (250 lbs) or hangs over the rear or sides of the vehicle may damage the vehicle. Load cargo so that it rests evenly between the crossrails, making sure to fasten cargo securely.
To prevent damage or loss of cargo when driving, check to make sure crossrails and cargo are securely fastened. Loading cargo on the roof rack will make the vehicle’s center of gravity higher. Avoid high speeds, sudden starts, sharp turns, sudden braking or abrupt maneuvers, otherwise it may result in loss of control. If driving for a long distance, on rough roads, or at high speeds, occasionally stop the vehicle to make sure the cargo remains in its place. Do not exceed the maximum vehicle capacity when loading the vehicle. For more information on vehicle capacity and loading, see Vehicle Load Limits on page 9‑27.
Storage
4-5
4. Repeat Steps 1 through 3 to the
opposite end of the crossrail.
5. Once both sides of the crossrail are loose, adjust the crossrail to the desired position.
6. Push the lever labeled “PULL”
from right to left to lock the crossrail in place.
7. Reinstall the end cap and turn
the crossrail key to lock the crossrail.
8. Repeat Steps 5 through 7 to the
opposite end of the crossrail.
Stop Tabs If the vehicle has a sunroof, it has a crossrail stop tab in the siderail. This tab prevents the crossrail from being moved past the opening of the sunroof and cargo from being loaded too far forward. The vehicle may have cargo tie downs. Once the cargo is loaded onto the crossrails, use the cargo tie downs to secure it . Do not load cargo directly on the roof of the vehicle. See Vehicle Load Limits on page 9‑27 for more information.
Adjusting the Crossrails To adjust the crossrails to fit a load:
1. Turn the crossrail key
counterclockwise to unlock the crossrail end cap. 2. Remove the end cap.
3. Pull the lever labeled “PULL” from left to right to loosen the crossrail.
4-6
Storage
2 NOTES
Instruments and Controls
5-1
Instruments and Controls
Controls
Steering Wheel Adjustment . . . 5-2
Horn . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Windshield Wiper/Washer . . . . . 5-2
Rear Window Wiper/Washer . . . . . . . . . . . . . . . . . . . . . . 5-3
Compass . . . . . . . . . . . . . . . . . . . . . 5-3
Clock . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
Power Outlets . . . . . . . . . . . . . . . . . 5-5
Cigarette Lighter . . . . . . . . . . . . . . 5-5
Ashtrays . . . . . . . . . . . . . . . . . . . . . . 5-6Warning Lights, Gauges, and Indicators
Warning Lights, Gauges, and
Indicators . . . . . . . . . . . . . . . . . . . . 5-6
Instrument Cluster . . . . . . . . . . . . 5-7
Speedometer . . . . . . . . . . . . . . . . . 5-8
Odometer . . . . . . . . . . . . . . . . . . . . . 5-8
Trip Odometer . . . . . . . . . . . . . . . . . 5-8Tachometer . . . . . . . . . . . . . . . . . . . 5-8
Fuel Gauge . . . . . . . . . . . . . . . . . . . 5-8
Engine Coolant TemperatureGauge . . . . . . . . . . . . . . . . . . . . . . . 5-9
Safety Belt Reminders . . . . . . . . 5-9
Airbag Readiness Light . . . . . . 5-10
Passenger Airbag StatusIndicator . . . . . . . . . . . . . . . . . . . . 5-11
Charging System Light . . . . . . . 5-11
MalfunctionIndicator Lamp . . . . . . . . . . . . . 5-12
Brake System Warning
Light . . . . . . . . . . . . . . . . . . . . . . . 5-14
Antilock Brake System (ABS)
Warning Light . . . . . . . . . . . . . . 5-15
Up-Shift Light . . . . . . . . . . . . . . . . 5-15
Traction Control System(TCS)/StabiliTrak® Light . . . . 5-16
Tire Pressure Light . . . . . . . . . . 5-16
Engine Oil Pressure Light . . . . 5-17
Security Light . . . . . . . . . . . . . . . . 5-17
High-Beam on Light . . . . . . . . . 5-17
Cruise Control Light . . . . . . . . . 5-18Information Displays
Driver Information
Center (DIC) . . . . . . . . . . . . . . . 5-18
Vehicle Messages
Vehicle Messages . . . . . . . . . . . 5-21
Battery Voltage and ChargingMessages . . . . . . . . . . . . . . . . . . 5-21
Brake System Messages . . . . 5-22
Door Ajar Messages . . . . . . . . . 5-22
Engine Cooling SystemMessages . . . . . . . . . . . . . . . . . . 5-23
Engine Oil Messages . . . . . . . . 5-23
Engine Power Messages . . . . 5-23
Fuel System Messages . . . . . . 5-24
Lamp Messages . . . . . . . . . . . . . 5-24
Ride Control SystemMessages . . . . . . . . . . . . . . . . . . 5-24
Service Vehicle Messages . . . 5-25
Tire Messages . . . . . . . . . . . . . . . 5-25
Transmission Messages . . . . . 5-25Universal Remote System
Universal Remote System . . . 5-26
Universal Remote SystemProgramming . . . . . . . . . . . . . . . 5-26
Universal Remote System
Operation . . . . . . . . . . . . . . . . . . 5-30
5-2
Instruments and Controls
Controls
Steering Wheel Adjustment A tilt wheel allows the steering wheel to be adjusted.
The tilt lever is on the left side of the steering column.
To tilt, hold the steering wheel and pull the tilt lever toward you. Raise or lower the wheel to a comfortable level, then release the tilt lever to lock the wheel in place. Do not adjust the steering wheel while driving.
Horn Press near the horn symbols or press on the steering wheel pad to sound the horn.
Windshield Wiper/Washer Turn the band with the N symbol to control the windshield wipers.
8 (Mist): Turn to z for a single wipe, then release. For several wipes, hold the band on z longer.
N (Adjustable Interval Wipes): Turn the band up for more frequent wipes or down for less frequent wipes.
6 : Slow wipes, turn the band to the first solid position past the delay settings. 1 : Fast wipes, turn the band to the second solid position past the delay settings. 9 (Off): Turns the wipers off. Clear ice and snow from the wiper blades before using them. If frozen to the windshield, carefully loosen or thaw them. If they become worn or damaged, install new blades or blade inserts. See Wiper Blade Replacement on page 10‑32
Windshield wipers work in all power modes, except when the ignition is set to LOCK/OFF. After the engine is turned off, wipers will work in Retained Accessory Power (RAP) mode until a door is opened. See Retained Accessory Power (RAP) on page 9‑35 .Instruments and Controls
5-3
Windshield Washer L (Washer Fluid): To spray washer fluid on the windshield, push the paddle marked with L at the top of the turn signal/lane change lever. The wipers will clear the window and then either stop or return to the preset speed. { WARNING
In freezing weather, do not use your washer until the windshield is warmed. Otherwise the washer fluid can form ice on the windshield, blocking your vision.
Rear Window Wiper/Washer
For vehicles with this feature, the knob is located on the instrument panel below the climate controls. Z (Rear Wiper): Turn to 1 for a slower wiping speed or to 2 for a faster wiping speed.
0 (Off): Turn to 0 for off. = (Washer Fluid): Press to wash and wipe the window. The rear window washer uses the same fluid bottle as the windshield washer. Check the fluid level if the windshield can be washed, but the rear windows cannot.
Compass
Compass Display The inside rearview mirror may have a compass display. Press z to turn the compass display on or off.
5-4
Instruments and Controls
Compass Calibration The compass may need to be calibrated if CAL is not displayed and the compass requires calibration. Press and hold O until CAL displays in the compass window, then release the button. The compass is now in calibration mode. . Drive the vehicle in circles at less than 8 km/h (5 mph) until CAL is no longer displayed in the compass window. Then continue to drive to make sure all eight directions are available.
. Drive the vehicle under normal
operating conditions.
Compass Variance The mirror is set to zone eight. If you do not live in zone eight or drive out of the area, the compass variance needs to be changed to the appropriate zone.
To adjust for compass variance: 1. Find your current location and variance zone number on the following zone map.
2. Press and hold O for
six seconds until ZONE displays. Release the button. The compass is now in zone mode.
3. Keep pressing O until the
desired zone number displays. Release the button. After four seconds, the new zone number locks in and the compass display returns.
Clock The clock can be set with the ignition on or off. Use the H and M buttons located on the lower left side of the radio. To set the clock: 1. Press and hold H until the
correct hour and AM or PM displays.
2. Press and hold M until the
correct minute displays.
Press DISP (Display) to display the time while the ignition is turned off.
Power Outlets The accessory power outlets can be used to connect auxiliary electrical equipment, such as a cellular phone. There are two accessory power outlets located under the climate control system. There is also one accessory power outlet located in the rear cargo area (H3 model only). Pull down the small cover to access the accessory power outlet. Notice: Leaving electrical equipment on for extended periods will drain the battery. Always unplug electrical equipment when not in use and do not plug in equipment that exceeds the maximum amperage rating of 20 amperes.
Instruments and Controls
5-5
Certain electrical accessories may not be compatible with the accessory power outlet and could result in blown vehicle or adapter fuses. If you experience a problem, see your dealer for additional information on accessory power outlets. Notice: Adding any electrical equipment to the vehicle can damage it or keep other components from working as they should. The repairs would not be covered by the vehicle warranty. Do not use equipment exceeding maximum amperage rating of 20 amperes. Check with your dealer before adding electrical equipment. When adding electrical equipment, be sure to follow the proper installation instructions included with the equipment.
Notice: Improper use of the power outlet can cause damage not covered by the vehicle warranty. Do not hang any type of accessory or accessory bracket from the plug because the power outlets are designed for accessory power plugs only.
Cigarette Lighter For vehicles with a lighter, push the lighter down and it will pop up when it is ready to be used. Notice: Holding a cigarette lighter in while it is heating does not let the lighter back away from the heating element when it is hot. Damage from overheating can occur to the lighter or heating element, or a fuse could be blown. Do not hold a cigarette lighter in while it is heating.
5-6
Instruments and Controls
Ashtrays For vehicles with a removable ashtray, it can be placed into the cupholder and be removed for cleaning. Notice: If papers, pins, or other flammable items are put in the ashtray, hot cigarettes or other smoking materials could ignite them and possibly damage the vehicle. Never put flammable items in the ashtray.
Warning Lights, Gauges, and Indicators Warning lights and gauges can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement. Paying attention to the warning lights and gauges could prevent injury. Warning lights come on when there could be a problem with a vehicle function. Some warning lights come on briefly when the engine is started to indicate they are working.
Gauges can indicate when there could be a problem with a vehicle function. Often gauges and warning lights work together to indicate a problem with the vehicle. When one of the warning lights comes on and stays on while driving, or when one of the gauges shows there may be a problem, check the section that explains what to do. Follow this manual's advice. Waiting to do repairs can be costly and even dangerous.
Instrument Cluster
Instruments and Controls
5-7
United States 3.7L L5 Automatic Transmission version shown, 5.3L V8, Canada and Manual Transmission
similar
5-8
Instruments and Controls
Speedometer The speedometer shows the vehicle's speed in both kilometers per hour (km/h) and miles per hour (mph).
Odometer The odometer shows how far the vehicle has been driven, in either kilometers or miles. This vehicle has a tamper-resistant odometer. If the vehicle needs a new odometer installed, the new one is set to the mileage of the old odometer. If this is not possible, it is set at zero and a label is put on the driver's door to show the old mileage reading.
Trip Odometer The vehicle has a trip odometer that indicates how far the vehicle has been driven since the trip odometer was last set to zero.
See “Trip Odometer” under Driver Information Center (DIC) on page 5‑18 for more information.
Tachometer The tachometer displays the engine speed in revolutions per minute (rpm).
Fuel Gauge
United States
Canada
The fuel gauge indicates about how much fuel there is remaining in the fuel tank. The ignition must be in ON/RUN. An arrow on the fuel gauge indicates the side of the vehicle the fuel door is on.
Here are three things that can happen but do not indicate a problem with the fuel gauge: . At the gas station, the gas pump
shuts off before the gauge reads full. It takes a little more or less fuel to fill up than the gauge indicated. For example, the gauge may have indicated the tank was half full, but it actually took a little more or less than half the tank's capacity to fill the tank. The gauge moves a little when turning a corner or speeding up. When the fuel in the fuel tank is low, a LOW FUEL message displays on the Driver Information Center (DIC). See Fuel System Messages on page 5‑24 for more information.
Engine Coolant Temperature Gauge
United States
Canada
This gauge shows the engine coolant temperature. If the gauge pointer is in the shaded area of the gauge, the engine is too hot. It means that the engine coolant has overheated. If the vehicle has been operating under normal driving conditions, pull off the road, stop your vehicle and turn off the engine as soon as possible. See Engine Overheating on page 10‑22 for more information.
Instruments and Controls
5-9
Passenger Safety Belt Reminder Light The passenger safety belt reminder light is by the passenger airbag status indicator.
Safety Belt Reminders
Driver Safety Belt Reminder Light There is a driver safety belt reminder light on the instrument panel cluster.
When the engine is started this light and a chime come on and stay on for several seconds to remind drivers to fasten their safety belts. The light also begins to flash. This cycle repeats if the driver remains unbuckled and the vehicle is moving. If the driver safety belt is already buckled, neither the light nor chime come on.
When the engine is started this light and the chime come on and stay on for several seconds to remind the passenger to fasten their safety belt. The light also begins to flash. This cycle repeats if the passenger remains unbuckled and the vehicle is moving. If the passenger safety belt is buckled, neither the chime nor the light comes on.
5-10
Instruments and Controls
The front passenger safety belt warning light and chime may turn on if an object is put on the seat such as a briefcase, handbag, grocery bag, laptop or other electronic device. To turn off the warning light and or chime, remove the object from the seat or buckle the safety belt.
Airbag Readiness Light There is an airbag readiness light on the instrument panel cluster, which shows the airbag symbol. The system checks the airbag's electrical system for malfunctions. The light indicates if there is an electrical problem. The system check includes the airbag sensor, the pretensioners, the airbag
modules, the wiring and the crash sensing and diagnostic module. For more information on the airbag system, see Airbag System on page 3‑27 .
This light comes on when the vehicle is started, and flashes for a few seconds. The light goes out when the system is ready. If the airbag readiness light stays on after the vehicle is started or comes on while driving, the airbag system may not work properly. Have the vehicle serviced right away.
{ WARNING If the airbag readiness light stays on after the vehicle is started or comes on while driving, it means the airbag system might not be working properly. The airbags in the vehicle might not inflate in a crash, or they could even inflate without a crash. To help avoid injury, have the vehicle serviced right away.
The airbag readiness light should flash for a few seconds when the engine is started. If the light does not come on then, have it fixed immediately.
Instruments and Controls
5-11
as a system check. Then, after several more seconds, the status indicator will light either ON or OFF, or either the on or off symbol to let you know the status of the right front passenger frontal airbag. If the word ON or the on symbol is lit on the passenger airbag status indicator, it means that the right front passenger frontal airbag is enabled (may inflate). If the word OFF or the off symbol is lit on the airbag status indicator, it means that the passenger sensing system has turned off the right front passenger frontal airbag. If, after several seconds, both status indicator lights remain on, or if there are no lights at all, there may be a problem with the lights or the passenger sensing system. See your dealer for service.
{ WARNING If the airbag readiness light ever comes on and stays on, it means that something may be wrong with the airbag system. To help avoid injury to yourself or others, have the vehicle serviced right away. See Airbag Readiness Light on page 5‑10 for more information, including important safety information.
Charging System Light
This light comes on briefly when the ignition key is turned, but the engine is not running, as a check to show it is working.
Passenger Airbag Status Indicator The vehicle has the passenger sensing system. See Passenger Sensing System on page 3‑35 for important safety information. The instrument panel has a passenger airbag status indicator.
United States
Canada
When the vehicle is started, the passenger airbag status indicator will light ON and OFF, or the symbol for on and off, for several seconds
5-12
Instruments and Controls
It should go out once the engine starts. If it stays on, or comes on while driving, there could be a problem with the charging system. A charging system message in the Driver Information Center (DIC) may also appear. See Battery Voltage and Charging Messages on page 5‑21 for more information. This light could indicate that there are problems with a generator drive belt, or that there is an electrical problem. Have it checked right away. If the vehicle must be driven a short distance with the light on, turn off all the accessories, such as the radio and air conditioner.
Malfunction Indicator Lamp A computer system called OBD II (On-Board Diagnostics-Second Generation) monitors operation of the fuel, ignition, and emission control systems. It ensures that
emissions are at acceptable levels for the life of the vehicle, helping to produce a cleaner environment.
This light comes on when the ignition is on, but the engine is not running, as a check to show it is working. If it does not, have the vehicle serviced by your dealer. If the check engine light comes on and stays on, while the engine is running, this indicates that there is an OBD II problem and service is required. Malfunctions often are indicated by the system before any problem is apparent. Being aware of the light can prevent more serious damage to the vehicle. This system assists the service technician in correctly diagnosing any malfunction.
Notice: If the vehicle is continually driven with this light on, after a while, the emission controls might not work as well, the vehicle's fuel economy might not be as good, and the engine might not run as smoothly. This could lead to costly repairs that might not be covered by the vehicle warranty. Notice: Modifications made to the engine, transmission, exhaust, intake, or fuel system of the vehicle or the replacement of the original tires with other than those of the same Tire Performance Criteria (TPC) can affect the vehicle's emission controls and can cause this light to come on. Modifications to these systems could lead to costly repairs not covered by the vehicle warranty. This could also result in a failure to pass a required Emission Inspection/Maintenance test. See Accessories and Modifications on page 10‑3.
Instruments and Controls
5-13
This light comes on during a malfunction in one of two ways: Light Flashing: A misfire condition has been detected. A misfire increases vehicle emissions and could damage the emission control system on the vehicle. Diagnosis and service might be required. The following can prevent more serious damage to the vehicle: . Reduce vehicle speed. . Avoid hard accelerations. . Avoid steep uphill grades.
If towing a trailer, reduce the amount of cargo being hauled as soon as it is possible.
If the light continues to flash, when it is safe to do so, stop the vehicle. Find a safe place to park the vehicle. Turn the key off, wait at least 10 seconds, and restart the engine. If the light is still flashing, follow the previous steps and see your dealer for service as soon as possible.
Light On Steady: An emission control system malfunction has been detected on the vehicle. Diagnosis and service might be required. An emission system malfunction might be corrected. . Make sure the fuel cap is fully
installed. See Filling the Tank on page 9‑68 . The diagnostic system can determine if the fuel cap has been left off or improperly installed. A loose or missing fuel cap allows fuel to evaporate into the atmosphere. A few driving trips with the cap properly installed should turn the light off. If the vehicle has been driven through a deep puddle of water, the vehicle's electrical system might be wet. The condition is usually corrected when the electrical system dries out. A few driving trips should turn the light off.
. Make sure to fuel the vehicle
with quality fuel. Poor fuel quality causes the engine not to run as efficiently as designed and may cause: stalling after start-up, stalling when the vehicle is changed into gear, misfiring, hesitation on acceleration, or stumbling on acceleration. These conditions might go away once the engine is warmed up. If one or more of these conditions occurs, change the fuel brand used. It will require at least one full tank of the proper fuel to turn the light off. See Recommended Fuel on page 9‑64 .
If none of the above have made the light turn off, your dealer can check the vehicle. The dealer has the proper test equipment and diagnostic tools to fix any mechanical or electrical problems that might have developed.
5-14
Instruments and Controls
Emissions Inspection and Maintenance Programs Some state/provincial and local governments have or might begin programs to inspect the emission control equipment on the vehicle. Failure to pass this inspection could prevent getting a vehicle registration. Here are some things to know to help the vehicle pass an inspection:
The vehicle will not pass this inspection if the check engine light is on with the engine running, or if the key is in ON/RUN and the light is not on. The vehicle will not pass this inspection if the OBD II (on-board diagnostic) system determines that critical emission control systems have not been completely diagnosed by the system. The vehicle would be considered not ready for inspection. This can happen if
the battery has recently been replaced or if the battery has run down. The diagnostic system is designed to evaluate critical emission control systems during normal driving. This can take several days of routine driving. If this has been done and the vehicle still does not pass the inspection for lack of OBD II system readiness, your dealer can prepare the vehicle for inspection.
Brake System Warning Light The vehicle's hydraulic brake system is divided into two parts. If one part is not working, the other part can still work and stop the vehicle. For good braking though, both parts need to be working well. If the warning light comes on, there could be a brake problem. Have the brake system inspected right away.
United States
Canada
This light comes on briefly when the ignition key is turned to ON/RUN. If it does not, have it fixed so it will be ready to warn if there is a problem. When the ignition is on, the brake system warning light comes on when the parking brake is set. See Parking Brake on page 9‑51
for more information. The light stays on if the parking brake does not release fully. If it stays on after the parking brake is fully released, it means there is a brake problem.If the light comes on while driving, pull off the road and stop. The brake pedal might be harder to push, or it might go closer to the floor. It can take longer to stop. If the light is still on, have the vehicle towed for service. See Towing the Vehicle on page 10‑90.
{ WARNING
The brake system might not be working properly if the brake system warning light is on. Driving with the brake system warning light on can lead to a crash. If the light is still on after the vehicle has been pulled off the road and carefully stopped, have the vehicle towed for service.
Instruments and Controls
5-15
Antilock Brake System (ABS) Warning Light
For vehicles with the Antilock Brake System (ABS), this light comes on briefly when the engine is started. If it does not, have the vehicle serviced by your dealer. If the system is working normally the indicator light will then go off. If the ABS light stays on, turn the ignition off. If the light comes on while driving, stop as soon as it is safely possible and turn the ignition off. Then start the engine again to reset the system. If the ABS light stays on, or comes on again while driving, the vehicle needs service. If the regular brake system warning light is not on, the vehicle still has brakes, but not antilock brakes.
If the regular brake system warning light is also on, the vehicle does not have antilock brakes and there is a problem with the regular brakes. See Brake System Warning Light on page 5‑14 . For vehicles with a Driver Information Center (DIC), see Brake System Messages on page 5‑22 for more information.
Up-Shift Light
The vehicle may have an up-shift light. When this light comes on, shift to the next higher gear if weather, road, and traffic conditions allow. See Manual Transmission on page 9‑44 for more information.
5-16
Instruments and Controls
Traction Control System (TCS)/StabiliTrak® Light
The StabiliTrak system or the Traction Control System (TCS) indicator/warning light comes on briefly while starting the engine. If it does not, have the vehicle serviced by your dealer. If the system is working normally the indicator light will then go off. The indicator/warning light flashes while the StabiliTrak or TCS system is working to control the vehicle on a low traction surface. If the TCS warning light comes on and stays on while driving, the vehicle needs service.
The light comes on when the TCS and the StabiliTrak system is turned off. If the TCS is off, wheel spin is not limited. If the StabiliTrak system is off, the system does not assist in controlling the vehicle. Turn on the TCS and the StabiliTrak system and the warning light turns off. See StabiliTrak System on page 9‑53 and Traction Control System (TCS) on page 9‑52 for more information
Tire Pressure Light
For vehicles with a tire pressure monitoring system, this light comes on briefly when the engine is started. It provides information about tire pressures and the Tire Pressure Monitoring System.
When the Light is On Steady This indicates that one or more of the tires are significantly underinflated. A tire pressure message in the Driver Information Center (DIC), can accompany the light. See Tire Messages on page 5‑25 for more information. Stop as soon as possible, and inflate the tires to the pressure value shown on the tire loading information label. See Tire Pressure on page 10‑51 for more information.
When the Light Flashes First and Then is On Steady This indicates that there may be a problem with the Tire Pressure Monitor System. The light flashes for about a minute and stays on steady for the remainder of the ignition cycle. This sequence repeats with every ignition cycle. See Tire Pressure Monitor Operation on page 10‑53 for more information.
Engine Oil Pressure Light
{ WARNING
Do not keep driving if the oil pressure is low. The engine can become so hot that it catches fire. Someone could be burned. Check the oil as soon as possible and have the vehicle serviced.
Notice: Lack of proper engine oil maintenance can damage the engine. The repairs would not be covered by the vehicle warranty. Always follow the maintenance schedule in this manual for changing engine oil.
Instruments and Controls
5-17
Security Light
The oil pressure light should come on briefly as the engine is started. If it does not come on have the vehicle serviced by your dealer. If the light comes on and stays on, it means that oil is not flowing through the engine properly. The vehicle could be low on oil and might have some other system problem. See your dealer.
This light flashes when the security system is activated. For more information, see Anti-Theft Alarm System on page 2‑9.
High-Beam on Light
The high-beam on light comes on when the high-beam headlamps are in use. See Headlamp High/Low-Beam Changer on page 6‑3 for more information.
5-18
Instruments and Controls
Cruise Control Light
Information Displays
This light comes on whenever the cruise control is set. The light goes out when the cruise control is turned off. See Cruise Control on page 9‑57 for more information.
Driver Information Center (DIC) The Driver Information Center (DIC) displays information such as the trip odometer, personalization features, and warning messages. The DIC display is located on the instrument panel cluster. The DIC comes on when the ignition is on. If a problem is detected, a warning message appears on the display. Pressing and releasing the trip odometer reset stem on the DIC acknowledges some current warnings or service messages. Some messages only clear after the required action has been taken. The DIC has different modes which can be accessed by pressing the trip odometer reset stem on the DIC. These modes are explained in the following section. The DIC trip odometer reset stem is located on
the instrument panel cluster next to the DIC display. To scroll through the available functions, press and release the reset stem. Trip Information
Odometer The odometer is automatically displayed on the DIC when you start the vehicle. The odometer shows the total distance the vehicle has been driven in either miles for the United States or kilometers for Canada.
Trip Odometer Press and release the reset stem until TRIP appears on the DIC display. The trip odometer shows the current distance traveled since the last reset of the trip odometer in either miles for the United States or kilometers for Canada. To reset the trip odometer, press and hold the reset stem until the display returns to zero.
Instruments and Controls
5-19
Engine Oil Life System With the engine off, turn the key to ON/RUN and then press the reset stem until OIL LIFE RESET appears — alternating between OIL LIFE and RESET — on the DIC display. The CHANGE OIL message alerts you to change the oil on a schedule consistent with your driving conditions. Always reset the OIL LIFE message after an oil change. To reset the message, see Engine Oil Life System on page 10‑11. In addition to the engine oil life system monitoring the oil life, additional maintenance is recommended in the Maintenance Schedule in this manual. See Engine Oil on page 10‑9 and Scheduled Maintenance on page 11‑2 for more information.
Language This feature allows you to choose the language in which the DIC display shows information. To set your choice for this feature: 1. With the engine off, turn the key to ON/RUN, but do not start the engine.
2. Close all doors so the DOORS
message does not display in the DIC.
3. Momentarily press and release the reset stem until the current language is displayed: English (default), Spanish, or French. 4. To select a different language, press and hold the reset stem until the next language appears.
5. Repeat Step 4 until the desired
language is displayed. Once the desired language is shown on the DIC display, the language is set.
6. To exit the language selection, momentarily press and release the reset stem. All DIC messages will now display in the language selected. Automatic Door Locks This feature allows you to program the door locks to a preferred setting. To set your choice for this feature: 1. With the engine off, turn the key
to LOCK/OFF. Do not remove the key from the ignition.
2. Press and hold the power door lock button until the DIC display shows the current door lock mode.
5-20
Instruments and Controls
3. To view the next available
mode, press and hold the reset stem until the mode appears. Release the reset stem and press and hold again to view the next mode.
4. Once the desired mode is shown on the DIC display, briefly press the reset stem to set your choice. The DIC display then clears.
The following are the available modes: Lock 1 (default): On vehicles with an automatic transmission, this mode locks all of the doors when the vehicle is shifted out of P (Park) and unlocks all of the doors when the vehicle is shifted into P (Park). On vehicles with a manual transmission, this mode locks all of the doors when the vehicle speed is greater than 24 km/h (15 mph) and unlocks all of the doors when the key is removed from the ignition.
Lock 2: On vehicles with an automatic transmission, this mode locks all of the doors when the vehicle is shifted out of P (Park) and unlocks the driver's door when the vehicle is shifted into P (Park). On vehicles with a manual transmission, this mode locks all of the doors when the vehicle speed is greater than 24 km/h (15 mph) and unlocks the driver's door when the key is removed from the ignition. Lock 3: On vehicles with an automatic transmission, this mode locks all of the doors when the vehicle is shifted out of P (Park). The doors will not automatically unlock. On vehicles with a manual transmission, this mode locks all of the doors when the vehicle speed is greater than 24 km/h (15 mph). The doors will not automatically unlock.
Remote Keyless Entry (RKE) Feedback This feature allows you to program the Remote Keyless Entry (RKE) feedback to a preferred setting. To set your choice for this feature: 1. With the engine off, turn the key
to LOCK/OFF. Do not remove the key from the ignition.
2. Press and hold the lock and unlock buttons on the RKE transmitter at the same time. Hold both buttons until the DIC display shows the current RKE feedback mode.
3. To view the next available
mode, press and hold the reset stem until the mode appears. Release the reset stem and press and hold again to view the next mode.
4. Once the desired mode is shown on the DIC display, briefly press the reset stem to set your choice. The DIC display then clears.
The following are the available modes: RFA 1 (default): This mode flashes the parking lamps when you press the lock or unlock buttons on the RKE transmitter. RFA 2: This mode flashes the parking lamps and sounds the horn when you press the lock button on the RKE transmitter. This mode also flashes the parking lamps when you press the unlock button on the RKE transmitter. RFA 3: This mode flashes the parking lamps and sounds the horn when you press the lock or unlock buttons on the RKE transmitter. RFA 4: This mode disables RKE feedback. There will be no feedback when you press the lock or unlock buttons on the RKE transmitter.
Instruments and Controls
5-21
Vehicle Messages Messages are displayed on the DIC to notify the driver that the status of the vehicle has changed and that some action may be needed by the driver to correct the condition. Multiple messages may appear one after another. The messages are displayed for several seconds each. Some messages may not require immediate action, but you should press and release the trip odometer reset stem to acknowledge that you received the messages and to clear them from the display. Each message must be acknowledged individually. Some messages cannot be cleared from the DIC display because they are more urgent. These messages require action before they can be cleared. You should take any messages that appear on the
display seriously and remember that clearing the messages only makes the messages disappear, not correct the problem. The following are the possible messages that can be displayed and some information about them.
Battery Voltage and Charging Messages
SERVICE CHARG (Charge) SYS (System) This message displays if there is a problem with the battery charging system. Under certain conditions, the battery warning light may also turn on in the instrument panel cluster. See Charging System Light on page 5‑11 . The battery will not be charging at an optimal rate and the vehicle will lose the ability to enter the fuel economy mode.
5-22
Instruments and Controls
The vehicle is safe to drive, however have the electrical system checked by your dealer. Press and release the reset stem to acknowledge the message and clear it from the display.
Brake System Messages
ABS (Antilock Brake System) FAULT This message displays if there is a problem with the Antilock Brake System (ABS). Check the ABS as soon as possible and have the vehicle serviced by your dealer. See Antilock Brake System (ABS) on page 9‑50 and Antilock Brake System (ABS) Warning Light on page 5‑15 for more information. Press and release the reset stem to acknowledge the message and clear it from the display.
BRAKES This message displays if there is a problem with the brakes. Check the brakes as soon as possible and have the vehicle serviced by your dealer. See Brakes on page 10‑26
and Brake System Warning Light on page 5‑14 for more information. Press and release the reset stem to acknowledge the message and clear it from the display. FLUID This message displays if the brake fluid is low. Check the brake fluid as soon as possible and have the vehicle serviced by your dealer. See Brake Fluid on page 10‑27 for more information. Press and release the reset stem to acknowledge the message and clear it from the display.HSA (Hill Start Assist) ON This message displays when the Hill Start Assist is enabled. See Hill Start Assist (HSA) on page 9‑52 for more information. PARK BRK (Brake) This message displays when the parking brake is set. See Parking Brake on page 9‑51 and Brake System Warning Light on page 5‑14 for more information. The message clears from the display after the parking brake is released or by pressing and releasing the reset stem.
Door Ajar Messages
DOORS This message displays when one or more of the doors is ajar. Check all the doors on the vehicle to make sure they are closed. The message clears from the display after all of the doors are closed.
Instruments and Controls
5-23
Engine Oil Messages
Engine Power Messages
CHANGE OIL This message displays when the oil needs to be changed. Check the oil in the vehicle as soon as possible and have the vehicle serviced by your dealer. See Engine Oil on page 10‑9 and Scheduled Maintenance on page 11‑2 for more information. Press and release the reset stem to acknowledge the message and clear it from the display. OIL This message displays when the oil pressure is low. See Engine Oil Pressure Light on page 5‑17 and Engine Oil on page 10‑9 for more information.
REDUCED POWER This message displays when the vehicle's engine power is reduced. Reduced engine power can affect the vehicle's ability to accelerate. If this message is on, but there is no reduction in performance, proceed to your destination. The performance may be reduced the next time the vehicle is driven. The vehicle may be driven at a reduced speed while this message is on, but acceleration and speed may be reduced. Anytime this message stays on, the vehicle should be taken to your dealer for service as soon as possible. Press and release the reset stem to acknowledge the message and clear it from the display.
Engine Cooling System Messages
AC (Air Conditioning) OFF This message displays when the engine coolant temperature is too high and the air conditioning in the vehicle needs to be turned off. See Engine Overheating on page 10‑22 and Climate Control Systems on page 8‑1 for more information. This message displays along with the ENG HOT message. ENG (Engine) HOT This message displays when the engine coolant temperature is hot. Check the engine coolant temperature gauge. See Engine Coolant Temperature Gauge on page 5‑9 . Have the vehicle serviced by your dealer as soon as possible if you suspect the engine is overheating. See Engine Overheating on page 10‑22 for more information.
5-24
Instruments and Controls
Fuel System Messages
Lamp Messages
FUEL CAP This message displays if the vehicle's fuel cap is either off or loose. Pull over as soon as possible and check to see if the fuel cap is secure. You may also see the check engine light on the instrument panel cluster. If the check engine light does come on when the fuel cap was loose, it may take a few driving trips before the light turns off. See Malfunction Indicator Lamp on page 5‑12 for more information if the light still remains on. Press and release the reset stem to acknowledge the message and clear it from the display. LOW FUEL This message displays if the level of fuel in the vehicle is low. Also check the fuel gauge. See Fuel Gauge on page 5‑8 for more information. Refill the fuel tank as soon as possible.
TURN SIGNAL This message displays when the turn signal is on for about 1.2 km (0.75 miles) of travel. Press and release the reset stem to acknowledge the message and clear it from the display.
Ride Control System Messages
SERVICE STAB (Stability) SYS (System) This message displays if there is a problem with the StabiliTrak® system. Have the vehicle serviced by your dealer. See StabiliTrak System on page 9‑53 for more information.
STAB (Stability) SYS (System) OFF This message displays when the StabiliTrak® system is turned off. See StabiliTrak System on page 9‑53 for more information. TRAC (Traction) OFF This message along with the traction off light displays when the Traction Control System (TCS) is turned off by pressing the TCS button. See Traction Control System (TCS) on page 9‑52 and Traction Control System (TCS)/StabiliTrak® Light on page 5‑16 for more information.
TRACTION FAILED This message displays if there is a problem with the Traction Control System (TCS). Check the TCS as soon as possible and have the vehicle serviced by your dealer. See Traction Control System (TCS)/ StabiliTrak® Light on page 5‑16 for more information. Press and release the reset stem to acknowledge the message and clear it from the display.
Service Vehicle Messages
SERV (Service) VEH (Vehicle) This message displays if the vehicle needs service. Have the vehicle serviced by your dealer as soon as possible.
Instruments and Controls
5-25
Tire Messages
LOW TIRE On vehicles with the Tire Pressure Monitor System (TPMS), this message displays if a low tire pressure is detected in any of the vehicle's tires. Press and release the reset stem to acknowledge the message and clear it from the display. The message appears at each ignition cycle until the tires are inflated to the correct inflation pressure. See Tires on page 10‑44
and Tire Pressure on page 10‑51 for more information on tires and the correct inflation pressures. SERV (Service) TPM (Tire Pressure Monitor) On vehicles with the Tire Pressure Monitor System (TPMS), this message displays if a part on the TPMS is not working properly. The tire pressure light also flashesand then remains on during the same ignition cycle. See Tire Pressure Light on page 5‑16 . Several conditions may cause this message to appear. See Tire Pressure Monitor Operation on page 10‑53 for more information. If the warning comes on and stays on, there may be a problem with the TPMS. See your dealer.
Transmission Messages
SERV (Service) 4WD (Four-Wheel Drive) This message displays when there is a problem with the transfer case control system. Check the transfer case on the vehicle and have it serviced by your dealer. See Four-Wheel Drive on page 9‑46 for more information about the transfer case. Press and release the reset stem to acknowledge the message and clear it from the display.
5-26
Instruments and Controls
Universal Remote System See Radio Frequency Statement on page 13‑16 for information regarding Part 15 of the Federal Communications Commission (FCC) Rules and RSS-210/211 of Industry and Science Canada. The FCC Grant of Equipment Authorization Certificate number is CB2SAHL3. The Canadian Registration ID number is 2791021849A.
Universal Remote System Programming
This system provides a way to replace up to three remote control transmitters used to activate devices such as garage door openers, security systems, and home automation devices. Do not use the Universal Home Remote with any garage door opener that does not have the stop and reverse feature. This includes any garage door opener model manufactured before April 1, 1982.
Read the instructions completely before attempting to program the Universal Home Remote. Because of the steps involved, it may be helpful to have another person available to assist you with programming the Universal Home Remote. Keep the original hand-held transmitter for use in other vehicles as well as for future Universal Home Remote programming. It is also recommended that upon the sale of the vehicle, the programmed Universal Home Remote buttons should be erased for security purposes. See “Erasing Universal Home Remote Buttons” later in this section. When programming a garage door, park outside of the garage. Park directly in line with and facing the garage door opener motor-head or gate motor-head. Be sure that people and objects are clear of the garage door or gate that is being programmed.
It is recommended that a new battery be installed in your hand-held transmitter for quicker and more accurate transmission of the radio-frequency signal. Programming the Universal Home Remote System For questions or help programming the Universal Home Remote System, call 1‐800‐355‐3515
or go to www.homelink.com. Programming a garage door opener involves time-sensitive actions, so read the entire procedure before starting. Otherwise, the device will time out and the procedure will have to be repeated.Instruments and Controls
5-27
To program up to three devices:
2. Hold the end of your hand-held
transmitter about 3 to 8 cm (1 to 3 inches) away from the Universal Home Remote buttons while keeping the indicator light in view. The hand-held transmitter was supplied by the manufacturer of your garage door opener receiver (motor head unit).
3. At the same time, press and
hold both the Universal Home Remote button to be used to control the garage door and the hand-held transmitter button. Do not release the Universal Home Remote button or the hand-held transmitter button until Step 4 has been completed. Some entry gates and garage door openers may require substitution of Step 3 with the procedure noted in “Gate Operator and Canadian Programming” later in this section.
1. From inside the vehicle, press and hold down the two outside buttons at the same time, releasing only when the Universal Home Remote indicator light begins to flash, after 20 seconds. This step will erase the factory settings or all previously programmed buttons. Do not hold down the buttons for longer than 30 seconds and do not repeat this step to program the remaining two Universal Home Remote buttons.
If the Universal Home Remote indicator light blinks rapidly for two seconds and then turns to a constant light, continue with the programming Steps 6
through 8. It may be helpful to have another person assist with the remaining steps.5-28
Instruments and Controls
4. The indicator light on the
Universal Home Remote will flash slowly at first and then rapidly after Universal Home Remote successfully receives the frequency signal from the hand-held transmitter. Release both buttons.
5. Press and hold the newly-trained
Universal Home Remote button and observe the indicator light. If the indicator light stays on continuously, the programming is complete and the garage door should move when the Universal Home Remote button is pressed and released. There is no need to continue programming Steps 6 through 8.
6. After Steps 1 through 5 have been completed, locate inside the garage the garage door opener receiver (motor-head unit). Locate the “Learn” or “Smart” button. The name and color of the button may vary by manufacturer.
7. Firmly press and release the
“Learn” or “Smart” button. After you press this button, you will have 30 seconds to complete Step 8.
Instruments and Controls
5-29
Gate Operator and Canadian Programming If you have questions or need help programming the Universal Home Remote System, call 1-800-355-3515 or go to www.homelink.com. Canadian radio-frequency laws require transmitter signals to time out or quit after several seconds of transmission. This may not be long enough for Universal Home Remote to pick up the signal during programming. Similarly, some U.S. gate operators are manufactured to time out in the same manner.
If you live in Canada, or you are having difficulty programming a gate operator or garage door opener by using the “Programming Universal Home Remote” procedures, regardless of where you live, replace Step 3 under “Programming Universal Home Remote” with the following: Continue to press and hold the Universal Home Remote button while you press and release every two seconds (cycle) the hand-held transmitter button until the frequency signal has been successfully accepted by the Universal Home Remote. The Universal Home Remote indicator light will flash slowly at first and then rapidly. Proceed with Step 4 under “Programming Universal Home Remote” to complete the training procedure.
8.
Immediately return to the vehicle. Firmly press and hold the Universal Home Remote button, selected in Step 3 to control the garage door, for two seconds, and then release it. If the garage door does not move, press and hold the same button a second time for two seconds, and then release it. Again, if the door does not move, press and hold the same button a third time for two seconds, and then release. The Universal Home Remote should now activate the garage door.
To program the remaining two Universal Home Remote buttons, begin with Step 2 of “Programming the Universal Home Remote System.” Do not repeat Step 1, as this will erase all previous programming from the Universal Home Remote buttons.
5-30
Instruments and Controls
Universal Remote System Operation
Using Universal Remote Press and hold the appropriate Universal Remote button for at least half of a second. The indicator light will come on while the signal is being transmitted. Erasing Universal Remote Buttons All programmed buttons should be erased when the vehicle is sold or the lease ends.
To erase all programmed buttons on the Universal Remote device:
Reprogramming a Single Universal Remote Button To reprogram any of the three Universal Remote buttons, repeat the programming instructions earlier in this section, beginning with Step 2. For help or information on the Universal Home Remote System, call the customer assistance phone number under Customer Assistance Offices on page 13‑3.
1. Press and hold down the
two outside buttons until the indicator light begins to flash, after 20 seconds.
2. Release both buttons.
Lighting
Exterior Lighting
Exterior Lamp Controls . . . . . . . . 6-1
Exterior Lamps OffReminder . . . . . . . . . . . . . . . . . . . . 6-3
Headlamp High/Low-Beam
Changer . . . . . . . . . . . . . . . . . . . . . 6-3
Flash-to-Pass . . . . . . . . . . . . . . . . . 6-3
Daytime RunningLamps (DRL) . . . . . . . . . . . . . . . . 6-3
Automatic Headlamp
System . . . . . . . . . . . . . . . . . . . . . . 6-4
Hazard Warning Flashers . . . . . 6-5Turn and Lane-Change
Signals . . . . . . . . . . . . . . . . . . . . . . 6-5
Fog Lamps . . . . . . . . . . . . . . . . . . . . 6-6
Off-Road Lamps . . . . . . . . . . . . . . 6-6Interior Lighting
Instrument Panel Illumination
Control . . . . . . . . . . . . . . . . . . . . . . 6-7
Dome Lamps . . . . . . . . . . . . . . . . . 6-7
Reading Lamps . . . . . . . . . . . . . . . 6-8Lighting Features
Exit Lighting . . . . . . . . . . . . . . . . . . . 6-8
Battery Load Management . . . . 6-8
Battery Power Protection . . . . . . 6-9Lighting
6-1
Exterior Lighting
Exterior Lamp Controls
The exterior lamps control is on the instrument panel to the left of the steering wheel. O (Exterior Lamps): Turn the control to select one of the four exterior lamp positions.
6-2
Lighting
9 (Off): Turns all exterior lamps and the Daytime Running Lamps (DRL) off. This is a momentary control that returns to AUTO when released. The DRL does not turn off on vehicles first sold in Canada, unless the following conditions are met:
The vehicle has an automatic transmission. The gear position is in P (Park). The headlamp switch is turned to 9.
AUTO (Automatic): Turns the headlamps on and off automatically, together with the following: . Sidemarker Lamps
Taillamps
. Parking Lamps
Instrument Panel Lights
Due to the momentary control, the automatic headlamps may be disabled even if the control is in the AUTO position.
To enable automatic lighting, do any of the following:
Turn the headlamp control from AUTO to off and release the control. It returns to the AUTO position by itself. Turn the headlamp control from the parking lamp or headlamp position to AUTO.
To disable automatic lighting, do any of the following:
Turn the headlamp control from AUTO to off and release the control. It returns back to the AUTO position by itself. Turn the headlamp control from AUTO to the parking lamp or headlamp position.
See Automatic Headlamp System on page 6‑4 for more information. Vehicles first sold in Canada with an automatic transmission cannot turn off automatic headlamps unless the gear position is in P (Park) and the headlamp control is turned to O.
Vehicles first sold in Canada with a manual transmission can turn off the automatic headlamps with the headlamp control; however, the parking lamps will remain on. ; (Parking Lamps): Turns on the parking lamps, together with the following: . Sidemarker Lamps
Taillamps License Plate Lamps Instrument Panel Lights
2 (Headlamps): Turns on the headlamps together with the previously listed lamps and lights. The headlamps can be switched from low to high beam by pushing the turn signal/lane change lever toward the instrument panel.
Exterior Lamps Off Reminder A headlamp reminder chime will sound if the following conditions are met:
The driver door is open.
. Parking lamps or headlamps are
manually turned on. The key is either not in the ignition switch, or it is in the LOCK/OFF position of the ignition switch.
The headlamp reminder cannot be turned off if the conditions listed above are met. In the automatic mode, the headlamps turn off once the ignition is in ACC/ACCESSORY.
Headlamp High/ Low-Beam Changer 2 3 Headlamp High/Low Beam Changer: Push the turn signal/lane change lever away from you to turn the high beams on. Pull the lever towards you to return to low beams.
This indicator light turns on in the instrument panel cluster when the high beam headlamps are on.
Lighting
6-3
Flash-to-Pass Pull the turn signal lever toward you, then release it, to signal that you are going to pass. If the headlamps are in the automatic position or on low beam, the high-beam headlamps will turn on. They stay on as long as the lever is held toward you. The high-beam indicator on the
