2008 Hummer H3 Owners Manual

Download PDF Manual
to shifting into REVERSE (R). Your transmission has a lock out feature which prevents a ﬁfth gear to reverse gear shift. Notice: Shifting to REVERSE (R) while your vehicle is moving forward could damage the transmission. The repairs would not be covered by your warranty. Shift to REVERSE (R) only after your vehicle is stopped. Use REVERSE (R), along with the parking brake, for parking your vehicle. Up-Shift Light This light will show you when to shift to the next higher gear for best fuel economy. When this light comes on, you can shift to the next higher gear if weather, road and traffic conditions permit. For the best fuel economy, accelerate slowly and shift when the light comes on. While you accelerate, it is normal for the light to go on and off if you quickly change the position of the accelerator. Ignore the shift light when you downshift. If your vehicle has four-wheel drive and has a manual transmission, disregard the shift light when the transfer case is in four-wheel low. For more information, see Up-Shift Light on page 3-32. Shift Speeds {CAUTION: If you skip a gear when you downshift, you could lose control of your vehicle. You could injure yourself or others. Do not shift down more than one gear at a time when you downshift. Full-Time Four-Wheel Drive Full-Time Four-Wheel Drive sends your engine’s driving power to all four wheels for extra traction. To get the most out of Full-Time Four-Wheel Drive, you must be familiar with its operation. 2-27 Transfer Case Buttons The transfer case buttons are located to the right of the instrument panel cluster. Use these switches to shift into and out of the different Full-Time Four-Wheel Drive modes. You can choose between four modes: 4 m(Four-Wheel High): This setting is used for driving in most street and highway situations. You can also use this setting for light or variable off-road conditions. N (NEUTRAL): Shift the vehicle’s transfer case to NEUTRAL only when towing your vehicle. See Recreational Vehicle Towing on page 4-48 or Towing Your Vehicle on page 4-48 for more information. 2-28 Notice: Driving on pavement in Four-Wheel High Lock or Four Wheel Low Lock for extended periods may cause premature wear on your vehicle’s powertrain and tires. Do not drive in Four-Wheel High Lock or Four-Wheel Low Lock on pavement for extended periods. 4 mQ (Four-Wheel-High Lock): Use this mode when you need extra traction in most off-road situations such as sand, mud, snow or level, rocky trails. Notice: Operating your vehicle in Four-Wheel-Low Lock above 30 mph (48 km/h) for any extended period of time could cause damage to the transfer case. Do not operate your vehicle in Four-Wheel-Low Lock above 30 mph (48 km/h) for extended periods. 4 nQ (Four-Wheel-Low Lock): This mode delivers extra torque to all four wheels and is used for extreme off-road conditions. You might choose 4-Wheel-Low Lock if you are driving in off-road situations, such as, deep sand, mud, or snow and climbing or descending steep hills. If the vehicle has a locking rear axle, when in this mode you can also choose to lock the rear axle for additional traction in extreme off-road situations. See Locking Rear Axle on page 4-6. Indicator lights in the buttons show which mode you are in. The indicator lights will come on brieﬂy when you turn on the ignition the mode the vehicle is in will stay on. If the lights do not come on, you should take your vehicle to your dealer for service. An indicator light will ﬂash while shifting the transfer case. It will remain lit when the shift is complete. If for some reason the transfer case cannot make a requested shift, it will return to the last chosen setting. If the SERV 4WD message on the Driver Information Center (DIC) stays on, you should take your vehicle to your dealer for service. See Service 4WD message under DIC Warnings and Messages on page 3-43. Shifting between Four-Wheel High and Four-Wheel-High Lock With the vehicle traveling less than 45 mph (72 km/h), press and release the Four-Wheel High or Four-Wheel-High Lock button. The indicator light will ﬂash while shifting. It will remain lit when the shift is complete. It may be necessary to drive backwards while turning for a distance of 25 feet (7.5 m) to get the lock feature to disengage. Shifting into Four-Wheel Low Lock Notice: Shifting the transmission into gear before the indicator light stops ﬂashing could cause damage to the transfer case. Always wait until the indicator light stops ﬂashing before putting the transmission back in gear. To shift into Four-Wheel-Low Lock, the ignition must be in ON and the vehicle must be stopped or moving less than 3 mph (5 km/h) with the transmission in NEUTRAL (N). The preferred method for shifting into Four-Wheel Low is to have your vehicle moving 1 to 2 mph (1.6 to 3.2 km/h). Press and release the Four-Wheel-Low Lock button. If your vehicle has a manual transmission, the clutch pedal must be pressed to the ﬂoor while you press the Four-Wheel-Low Lock button, or the shift will not be completed. You must wait for the Four-Wheel-Low Lock indicator light to stop ﬂashing and remain lit before shifting your transmission in gear. It is normal for your vehicle to have engagement noise and bump when shifting between Four-Wheel Low and Four-Wheel High ranges or from NEUTRAL with the engine running. If the Four-Wheel-Low Lock button is pressed when your vehicle is in gear and/or moving too fast, the Four-Wheel-Low Lock indicator light will ﬂash for 15 seconds and not complete the shift unless your vehicle is moving less than 3 mph (5 km/h) and the transmission is in NEUTRAL (N). After 15 seconds the transfer case will return to the last chosen setting. 2-29 Shifting Out of Four-Wheel-Low Lock Notice: Shifting the transmission into gear before the indicator light stops ﬂashing could cause damage to the transfer case. Always wait until the indicator light stops ﬂashing before putting the transmission back in gear. To shift out of Four-Wheel-Low Lock, your vehicle must be stopped or moving less than 3 mph (5 km/h) with the transmission in NEUTRAL (N) and the ignition in ON. The preferred method for shifting out of Four-Wheel-Low Lock is to have your vehicle moving 1 to 2 mph (1.6 to 3.2 km/h). Press and release the Four-Wheel High or Four-Wheel-High Lock button. If your vehicle has a manual transmission, the clutch pedal must be pressed to the ﬂoor while you press the Four-Wheel High or Four-Wheel-High Lock button, or the shift will not be completed. You must wait for the Four-Wheel High or Four-Wheel-High Lock indicator light to stop ﬂashing and remain lit before shifting your transmission into gear. It is normal for your vehicle to have engagement noise and bump when shifting between Four-Wheel Low and Four-Wheel High ranges or from NEUTRAL with the engine running. If the Four-Wheel High or Four-Wheel-High Lock button is pressed when your vehicle is in gear and/or moving too fast, the Four-Wheel High or Four-Wheel-High Lock indicator light will ﬂash for 15 seconds but will not complete the shift unless your vehicle is moving less than 3 mph (5 km/h) and the transmission is in NEUTRAL (N). Shifting Into NEUTRAL To shift the transfer case to NEUTRAL, do the following: 1. Set the parking brake. 2. Start the vehicle by turning the ignition to START. 3. Put the transmission in NEUTRAL (N). If your vehicle has a manual transmission, press and hold the clutch pedal down while you perform Steps 5 through 9. 4. Shift the transfer case to Four-Wheel High. 2-30 {CAUTION: Shifting an all-wheel-drive vehicle’s transfer case into NEUTRAL can cause your vehicle to roll even if the automatic transmission is in PARK (P) or the manual transmission is in any gear. You or others could be injured. Make sure the parking brake is ﬁrmly set before you shift the transfer case to NEUTRAL. 5. Simultaneously press and hold the Four-Wheel High and Four-Wheel-Low Lock buttons for 10 seconds. The NEUTRAL light will come on when the transfer case shift to NEUTRAL is complete. 6. Press and hold the regular brake pedal and Shift the transmission to REVERSE (R) for one second, then shift the transmission for one second to DRIVE (D) for an automatic transmission, or FIRST (1) for vehicles have a manual transmission and then let out the clutch. This is to ensure the transfer case is in NEUTRAL. If not, repeat this procedure starting at Step 3. 7. Turn the engine off, by turning the key to ACC. 8. Place the transmission shift lever in PARK (P) for an automatic transmission, or FIRST (1) for vehicles that have a manual transmission. 9. Turn the ignition to LOCK/OFF. Shifting Out of NEUTRAL To shift out of NEUTRAL: 1. Set the parking brake and apply the regular brake pedal. 2. Shift the transmission to NEUTRAL (N) for an automatic transmission, or press the clutch pedal for vehicles that have a manual transmission. Then turn the ignition to ON with the engine off. 3. Press the button for the desired transfer case shift position (Four-Wheel High, Four-Wheel-High Lock or Four-Wheel-Low Lock). After the transfer case has shifted out of NEUTRAL the light will go out. 4. Release the parking brake. Notice: Shifting the transmission into gear before the indicator light stops ﬂashing could cause damage to the transfer case. Always wait until the indicator light stops ﬂashing before putting the transmission back in gear. 5. You may start the engine and shift the transmission to the desired position. 2-31 Parking Brake The parking brake pedal is located to the left of the regular brake pedal, near the driver’s door. To set the parking brake, hold the regular brake pedal down with your right foot. Push the parking brake pedal down to its fully-applied position with your left foot. A chime will activate and the brake warning light, located on the instrument panel, will ﬂash when the parking brake is applied and the vehicle is moving at least 3 mph (5 km/h) for at least three seconds. The chime will deactivate and the light will turn off when the parking brake is set and the vehicle is moving below 3 mph (5 km/h). See Brake System Warning Light on page 3-33. 2-32 To release the parking brake, hold the regular brake pedal down. Pull the bottom edge of the lever, located above the parking brake pedal, with the parking brake symbol, directly rearward to release the parking brake. If the ignition is on when the parking brake is released, the brake system warning light will go off. Notice: Driving with the parking brake on can overheat the brake system and cause premature wear or damage to brake system parts. Make sure that the parking brake is fully released and the brake warning light is off before driving. If you are towing a trailer and are parking on any hill, see Towing a Trailer on page 4-50. Shifting Into PARK (P) (Automatic Transmission) {CAUTION: {CAUTION: It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. Your vehicle can roll. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle will not move, even when you are on fairly level ground, use the steps that follow. If you are pulling a trailer, see Towing a Trailer on page 4-50. 1. Hold the brake pedal down with your right foot and set the parking brake. See Parking Brake on page 2-32 for more information. With all-wheel drive, your vehicle will be free to roll — even if your shift lever is in PARK (P) — if your transfer case is in NEUTRAL. So, be sure the transfer case is in a drive gear, four-wheel high (4H) or four-wheel low (4L) — not in NEUTRAL. 2. Move the shift lever into PARK (P) by pressing the shift lever button and moving the lever as far forward as it will go. 3. Turn the ignition key to LOCK/OFF. 4. Remove the key and take it with you. If you can leave your vehicle with the key, your vehicle is in PARK (P). 2-33 Torque Lock (Automatic Transmission) If you are parking on a hill and you do not shift your transmission into PARK (P) properly, the weight of the vehicle may put too much force on the parking pawl in the transmission. You may ﬁnd it difficult to pull the shift lever out of PARK (P). This is called “torque lock.” To prevent torque lock, set the parking brake and then shift into PARK (P) properly before you leave the driver’s seat. To ﬁnd out how, see Shifting Into PARK (P) (Automatic Transmission) on page 2-33. When you are ready to drive, move the shift lever out of PARK (P) before you release the parking brake. If torque lock does occur, you may need to have another vehicle push yours a little uphill to take some of the pressure from the parking pawl in the transmission, so you can pull the shift lever out of PARK (P). Leaving Your Vehicle With the Engine Running (Automatic Transmission) {CAUTION: It can be dangerous to leave your vehicle with the engine running. Your vehicle could move suddenly if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. And, if you leave the vehicle with the engine running, it could overheat and even catch ﬁre. You or others could be injured. Do not leave your vehicle with the engine running. If you have to leave your vehicle with the engine running, be sure your vehicle is in PARK (P) and your parking brake is ﬁrmly set before you leave it. After you have moved the shift lever into PARK (P), hold the regular brake pedal down. Then, see if you can move the shift lever away from PARK (P) without ﬁrst pressing the shift lever button. If you can, it means that the shift lever was not fully locked into PARK (P). 2-34 Shifting Out of PARK (P) (Automatic Transmission) Your vehicle has an automatic transaxle shift lock control system. You have to fully apply your regular brakes before you can shift from PARK (P) when the ignition is RUN. See Automatic Transmission Operation on page 2-23. The shift lock control system is designed to do the following: (cid:129) Prevent the ignition key from being removed unless the shift lever is in PARK (P). (cid:129) Prevent movement of the shift lever out of PARK (P), unless the ignition is in ON/RUN and the regular brake pedal is applied. The shift lock control system is always functional except in the case of a dead battery or low voltage (less than 9 V) battery. If your vehicle has an uncharged battery or a battery with low voltage, try charging or jump starting the battery. See Jump Starting on page 5-42 for more information. To shift out of PARK (P) use the following: 1. Apply the brake pedal. 2. Move the shift lever to the desired position. If you still are unable to shift out of PARK (P): 1. Ease the pressure on the shift lever. 2. While holding down the brake pedal, push the shift lever all the way into PARK (P) 3. Move the shift lever to the desired position. If you are still having a problem shifting, then have your vehicle serviced soon. Parking Your Vehicle (Manual Transmission) Your vehicle has a manual transmission. Before you get out of your vehicle, move the shift lever into REVERSE (R), and ﬁrmly apply the parking brake. Once the shift lever has been placed into REVERSE (R) with the clutch pedal pressed in, turn the ignition key to LOCK, remove the key and release the clutch. If you are parking on a hill, or if your vehicle is pulling a trailer, see Towing a Trailer on page 4-50. 2-35 Parking Over Things That Burn Engine Exhaust {CAUTION: {CAUTION: Things that can burn could touch hot exhaust parts under your vehicle and ignite. Do not park over papers, leaves, dry grass, or other things that can burn. 2-36 Engine exhaust can kill. It contains the gas carbon monoxide (CO), which you cannot see or smell. It can cause unconsciousness and death. You might have exhaust coming in if: (cid:129) The exhaust system sounds strange or different. (cid:129) Your vehicle gets rusty underneath. (cid:129) Your vehicle was damaged in a collision. (cid:129) Your vehicle was damaged when driving over high points on the road or over road debris. (cid:129) Repairs were not done correctly. (cid:129) Your vehicle or the exhaust system has been modiﬁed improperly. If you ever suspect exhaust is coming into your vehicle: (cid:129) Drive it only with all the windows down to blow out any CO; and (cid:129) Have your vehicle ﬁxed immediately. Running the Engine While Parked It is better not to park with the engine running. But if you ever have to, here are some things to know. {CAUTION: {CAUTION: Idling the engine with the climate control system off could allow dangerous exhaust into your vehicle. See the earlier caution under Engine Exhaust on page 2-36. Also, idling in a closed-in place can let deadly carbon monoxide (CO) into your vehicle even if the climate control fan is at the highest setting. One place this can happen is a garage. Exhaust — with CO — can come in easily. NEVER park in a garage with the engine running. Another closed-in place can be a blizzard. See Winter Driving on page 4-35. It can be dangerous to get out of your vehicle if the automatic transmission shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. Your vehicle can roll. Do not leave your vehicle when the engine is running unless you have to. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle will not move, even when it is on fairly level ground, always set the parking brake and move the automatic transmission shift lever to PARK (P), or the manual transmission shift lever to NEUTRAL. Follow the proper steps to be sure your vehicle will not move. See Shifting Into PARK (P) (Automatic Transmission) on page 2-33 and Parking Your Vehicle (Manual Transmission) on page 2-35. If you are pulling a trailer with your vehicle, see Towing a Trailer on page 4-50. 2-37 Mirrors Automatic Dimming Rearview Mirror with OnStar®, Compass and Temperature Display Your vehicle may have this feature. When on, the automatic dimming mirror dims to the proper level to minimize glare from lights behind you after dark. The mirror has a dual display in the upper right corner of the mirror face that shows the compass reading and the outside temperature. Control buttons for the OnStar® system are at the bottom of the mirror. See OnStar® System on page 2-48 for more information about the services OnStar® provides. Y: This button is used as a toggle for changing displays and as an on/off toggle during a function. Your vehicle may also have a Rear Vision Camera. See Rear Vision Camera on page 2-44 for more information. Slide-Out Video Feature Enable Press and hold Y for three seconds to toggle the slide-out video feature on/off. An indicator light will turn on at the time the slide-out video is enabled. If the slide-out video feature is on, each time the vehicle is put into reverse, the slide-out video screen will extend. See Rear Vision Camera on page 2-44 for more information. The slide-out video feature will remain in the current on/off state each time the ignition goes through its cycle. Slide-Out Video Cleaning The slide-out video has to be enabled before the cleaning process can take place. (cid:129) Press and hold Y for six seconds or until the lower indicator light turns on. (cid:129) While extended for cleaning, neither the screen nor the camera will have power. (cid:129) Press Y brieﬂy or wait 30 seconds to end cleaning. The screen will then retract. 2-38 Automatic Dimming Mirror Operation The automatic dimming mirror comes on each time the ignition is turned to start. To turn the automatic dimming feature off or back on, press and hold Y for nine seconds. The indicator light on the mirror is lit when the automatic dimming feature is on. Temperature Display To adjust between Fahrenheit and Celsius: (cid:129) Press Y for approximately four seconds to toggle the display from F (Fahrenheit) to C (Celsius) to OFF. The temperature display will remain in its current state each time the ignition goes through its cycle. (cid:129) At start up, if the vehicle has been off for less than two and a half hours, and the last stored temperature was less than the current termperature, the sensor will increase 1°F every two minutes until the correct temperature is displayed. If the vehicle has been off more than two and a half hours, or the last stored temperature is greater than the current temperature, the current temperature immediately displays. If the temperature is 37°F (3°C) or lower, ICE will ﬂash on the temperature display. This display will ﬂash every two seconds for a period of one minute. If an abnormal temperature reading is displayed for an extended period of time, see your dealer/retailer. Under certain circumstances, a delay in updating the temperature is normal. Compass Display Press the Y button, located at the bottom of the mirror, next to the OnStar® control buttons to turn the compass/temperature display on or off. If CAL is not displayed, press and hold Y for 15 seconds, or until CAL is displayed. The compass is now in calibration mode. For more information, see “Compass Calibration” following. The mirror can be calibrated in one of two ways: (cid:129) Drive the vehicle in circles at less than 5 mph (8 km/h) until the CAL is no longer displayed in the compass window. Then continue to drive to make sure all eight directions are available. (cid:129) Drive the vehicle under normal operating conditions. 2-39 (cid:129) (cid:129) Compass Variance The mirror is set in zone eight upon leaving the factory. It will be necessary to adjust the compass to compensate for compass variance if the vehicle is outside of zone eight. Under certain circumstances, as during a long distance cross-country trip, it will be necessary to adjust for compass variance. Compass variance is the difference between earth’s magnetic north and true geographic north. If not adjusted to account for compass variance, the compass could give false readings. To adjust for compass variance: 1. Find your current location and variance zone number on the following zone map. 2-40 2. Press and hold Y for 12 seconds until a zone number appears in the display. The compass is now in zone mode. 3. Keep pressing the Y until the desired zone number appears in the display. Release the button. After approximately four seconds of inactivity, the new zone number will be locked in and the compass/temperature display will return. Cleaning the Mirror Use a paper towel or similar material dampened with glass cleaner. Do not spray glass cleaner directly on the mirror as that could cause the liquid cleaner to enter the mirror housing. Automatic Dimming Rearview Mirror with Compass and Temperature Display Your vehicle may have this mirror. When on, an automatic dimming mirror will dim to the proper level to minimize glare from lights behind you after dark. The mirror also includes a dual display in the upper right corner of the mirror with the compass reading and the outside temperature. Yb: Brieﬂy press this button to turn the display on or off. Your vehicle may also have a Rear Vision Camera. See Rear Vision Camera on page 2-44 for more information. Temperature Display The temperature can be displayed by pressing the compass/temperature button. Pressing the compass/ temperature button once brieﬂy, will toggle the display reading on and off. To alternate the temperature reading between Fahrenheit and Celsius, press and hold the compass/temperature button for approximately three seconds until the display blinks F and C. After approximately ﬁve seconds of inactivity, the display will stop blinking and display the last selection made. If an abnormal reading is displayed, see your dealer/retailer. Automatic Dimming Mirror Operation O: Press this button to turn the automatic dimming feature on or off. The indicator light to the left of the button will turn on to indicate when the feature is on. Once the mirror is turned off, it will remain off until it is turned back on, or until the vehicle is restarted. Compass Operation Press the compass/temperature button once brieﬂy to turn the display on or off. 2-41 Compass Calibration The compass may need calibration if one of the following occurs: If CAL is displayed while driving in the vehicle. (cid:129) After approximately ﬁve seconds, the display does not show a compass heading, N for North, for example, there may be a strong magnetic ﬁeld interfering with the compass. Such interference may be caused by a magnetic antenna mount, magnetic note pad holder, or a similar magnetic item. The compass does not display the correct heading and the compass zone variance is set correctly. In order to calibrate, CAL must be displayed in the mirror compass windows. If CAL is not displayed, push in the compass/temperature button for approximately nine seconds or until CAL is displayed. The compass can be calibrated by driving the vehicle in circles at 5 mph (8 km/h) or less until the display reads a direction. Compass Variance The mirror is set in zone eight upon leaving the factory. It will be necessary to adjust the compass to compensate for compass variance if the vehicle is outside zone eight. Under certain circumstances, as during a long distance cross-country trip, it will be necessary to adjust for compass variance. 2-42 Compass variance is the difference between earth’s magnetic north and true geographic north. If not adjusted to account for compass variance, your compass could give false readings. To adjust for compass variance: 1. Find your current location and variance zone number on the following zone map. 2. Press and hold the compass/temperature button for six seconds until a zone number appears in the display. (cid:129) (cid:129) 3. Press the compass/temperature button on the bottom of the mirror until the new zone number appears in the display. After you stop pressing the button, the display will show a compass direction within a few seconds. Cleaning the Mirror Use a paper towel or similar material dampened with glass cleaner. Do not spray glass cleaner directly on the mirror as that may cause the liquid cleaner to enter the mirror housing. Outside Power Mirrors The outside power mirror controls are located on the driver’s door. To adjust the power mirrors, do the following: 1. Press the left side of the selector switch to choose the driver side mirror. Press the right side of the selector switch to choose the passenger side mirror. 2. Use the round, four-way control pad to move the mirror in the desired direction. If the mirror begins making a ratcheting sound, the mirror has reached the end of its travel and can go no farther in that direction. To stop the sound, reverse the mirror direction using the control pad. The mirrors can be manually folded inward to prevent damage when going through an automatic car wash or conﬁned space. Pull the mirror toward the vehicle to fold. To return the mirror to its original position, push outward. Be sure to return both mirrors to the unfolded position before driving. 2-43 Outside Convex Mirror Object Detection Systems {CAUTION: A convex mirror can make things (like other vehicles) look farther away than they really are. If you cut too sharply into the right lane, you could hit a vehicle on your right. Check your inside mirror or glance over your shoulder before changing lanes. The passenger side mirror is convex. A convex mirror’s surface is curved so more can be seen from the driver seat. It also makes things, like other vehicles, look farther away than they really are. Rear Vision Camera Your vehicle may be equipped with a rear vision camera system. Read this entire section before using the camera system. The rear vision camera system is designed to help the driver when backing up by displaying a view of the area behind the vehicle. When the driver shifts the vehicle into REVERSE (R), the video screen will automatically slide out from the rear view mirror. Once the driver shifts out of REVERSE (R), the video screen will slide back into the rear view mirror after a delay. The display has a guideline overlay that can help the driver align the vehicle when backing into a parking spot. To turn off the rear vision camera system, do the following: 1. Place the vehicle shift lever in PARK (P). 2. Turn the ignition key to the ACCESSORY position. 3. Press the right mirror button brieﬂy; the right green light indicator will turn off. The rear camera vision display is now disabled. 2-44 To turn on the rear camera vision feature again, press the right mirror button brieﬂy. The green light indicator will illuminate. The rear camera vision system is now enabled and the display will slide out from the mirror normally. To manually slide out the rear camera screen for cleaning, do the following: 1. Place the vehicle shift lever in PARK (P). 2. Turn the ignition key to the ACCESSORY or RUN position. 3. Press and hold the right mirror button for ﬁve seconds. The display will slide out from the mirror for 30 seconds; the right green LED indicator will remain illuminated. The camera screen will not be on when it slides out of the mirror. 4. If additional time is required for cleaning, repeat step 3. To resume normal operation, press the right button momentarily while the rear camera screen is out or wait 30 seconds for screen to slide back into the mirror. For more information on the automatic dimming, compass, and temperature features of the mirror, see Automatic Dimming Rearview Mirror with Compass and Temperature Display on page 2-41. {CAUTION: The Rear Vision Camera (RVC) system does not replace driver vision. RVC does not: (cid:129) Detect objects that are outside the camera’s ﬁeld of view, below the bumper, or underneath the vehicle. (cid:129) Detect children, pedestrians, bicyclists, or pets. Do not back the vehicle by only looking at the rear vision camera screen, or use the screen during longer, higher speed backing maneuvers or where there could be cross-traffic. Your judged distances using the screen will differ from actual distances. So if you do not use proper care before backing up, you could hit a vehicle, child, pedestrian, bicyclist, or pet, resulting in vehicle damage, injury, or death. Even though the vehicle has the RVC system, always check carefully before backing up by checking behind your vehicle. 2-45 Area Displayed On Screen The image is provided by the camera located on the rear bumper. The camera does not display objects which are close to either corner of the bumper or under the bumper. The spare tire and carrier extends rearward of the rear bumper. The area displayed on the screen may vary according to vehicle orientation or road conditions. Notice: The spare tire extends farther away from rear of the vehicle than the trailer hitch shown on rear vision camera display. Your spare tire could hit an object even though there appears to be enough distance on the display between the trailer hitch and objects behind you causing vehicle or property damage. Do not use this system to judge the distance between the spare tire and objects behind you. The following illustration shows the ﬁeld of view that the camera provides. The camera uses a special lens. The distance of the image that appears on the screen differs from the actual distance. The area displayed by the camera is limited. 2-46 When the System Does Not Seem To Work Properly The rear vision camera system may not work properly or display a clear image in the following situations: In the dark. (cid:129) When the sun or the beam of headlights is shining directly into the camera lens. If ice, snow, mud, or anything else builds up on the camera lens. Clean the lens, rinse it with water, and wipe it with a soft cloth. If the back of the vehicle is in an accident, the position and mounting angle of the camera may change or the camera may be affected. Be sure to have the camera and its position and mounting angle checked at your dealer. (cid:129) Extreme high or low temperatures or extreme temperature changes can affect the image displayed. 2-47 (cid:129) (cid:129) (cid:129) For more information, visit onstar.com or onstar.ca, contact OnStar at 1-888-4-ONSTAR (1-888-466-7827) or TTY 1-877-248-2080, or press the OnStar button to speak with an OnStar advisor 24 hours a day, 7 days a week. Not all OnStar features are available on all vehicles. To check if your vehicle is equipped to provide the services described below, or for a full description of OnStar services and system limitations, see the OnStar Owner’s Guide in your glove box or visit onstar.com. OnStar Services For new vehicles equipped with OnStar, the Safe & Sound Plan, or the Directions & Connections Plan is included for one year from the date of purchase. You can extend this plan beyond the ﬁrst year, or upgrade to the Directions & Connections Plan. For more information, press the OnStar button to speak with an advisor. Some OnStar services (such as Remote Door Unlock or Stolen Vehicle Location Assistance) may not be available until you register with OnStar. OnStar® System OnStar uses several innovative technologies and live advisors to provide you with a wide range of safety, security, information, and convenience services. If your airbags deploy, the system is designed to make an automatic call to OnStar Emergency advisors who can request emergency services be sent to your location. If you lock your keys in the vehicle, call OnStar at 1-888-4-ONSTAR and they can send a signal to unlock your doors. If you need roadside assistance, press the OnStar button and they can contact Roadside Service for you. OnStar service is provided to you subject to the OnStar Terms and Conditions. You may cancel your OnStar service at any time by contacting OnStar as provided below. A complete OnStar Owner’s Guide and the OnStar Terms and Conditions are included in the vehicle’s OnStar Subscriber glove box literature. 2-48 Available Services with Safe & Sound Plan (cid:129) Automatic Notiﬁcation of Airbag Deployment (cid:129) Advanced Automatic Crash Notiﬁcation (AACN) (If equipped) Link to Emergency Services (cid:129) Roadside Assistance (cid:129) Stolen Vehicle Location Assistance (cid:129) AccidentAssist (cid:129) Remote Door Unlock/Vehicle Alert (cid:129) OnStar Vehicle Diagnostics (cid:129) GM Goodwrench® On Demand Diagnostics (cid:129) OnStar Hands-Free Calling with 30 complimentary minutes (cid:129) OnStar Virtual Advisor (U.S. Only) Available Services included with Directions & Connections Plan (cid:129) All Safe and Sound Plan Services (cid:129) Driving Directions - Advisor delivered or OnStar Turn-by-Turn Navigation (If equipped) (cid:129) RideAssist Information and Convenience Services OnStar Hands-Free Calling OnStar Hands-Free Calling allows eligible OnStar subscribers to make and receive calls using voice commands. Hands-Free Calling is fully integrated into the vehicle, and can be used with OnStar Pre-Paid Minute Packages. Hands-Free Calling may also be linked to a Verizon Wireless service plan in the U.S. or a Bell Mobility service plan in Canada, depending on eligibility. To ﬁnd out more, refer to the OnStar Owner’s Guide in the vehicle’s glove box, visit www.onstar.com or www.onstar.ca, or speak with an OnStar advisor by pressing the OnStar button or calling 1-888-4-ONSTAR (1-888-466-7827). OnStar Virtual Advisor OnStar Virtual Advisor is a feature of OnStar Hands-Free Calling that uses your minutes to access location-based weather, local traffic reports, and stock quotes. By pressing the phone button and giving a few simple voice commands, you can browse through the various topics. See the OnStar Owner’s Guide for more information. (Only available in the continental U.S.) 2-49 (cid:129) (cid:129) Additional OnStar Controls Your vehicle may have a button, located on the driver’s side of the instrument panel, that can be used to interact with OnStar. Use this button to dial numbers into voicemail systems or to dial phone number extensions. See the OnStar Owner’s Guide for more information. How OnStar Service Works In order to provide you with OnStar services, your vehicle’s OnStar system has the capability of recording and transmitting vehicle information. This information is automatically sent to an OnStar Call Center at the time of an OnStar button press, Emergency button press or if your airbags or AACN system deploys. The vehicle information usually includes your GPS location and, in the event of a crash, additional information regarding the accident that your vehicle has been involved in (e.g. the direction from which your vehicle was hit). When you use the Virtual Advisor feature of OnStar Hands-Free Calling, your vehicle also sends OnStar your GPS location so that we can provide you with location-based services. OnStar service cannot work unless your vehicle is in a place where OnStar has an agreement with a wireless service provider for service in that area. OnStar service also cannot work unless you are in a place where the wireless service provider OnStar has hired for that area has coverage, network capacity and reception when the service is needed, and technology that is compatible with the OnStar service. Not all services are available everywhere, particularly in remote or enclosed areas, or at all times. OnStar service that involves location information about your vehicle cannot work unless GPS satellite signals are unobstructed and available in that place as well. Your vehicle must have a working electrical system (including adequate battery power) for the OnStar equipment to operate. There are other problems OnStar cannot control that may prevent OnStar from providing OnStar service to you at any particular time or place. Some examples are damage to important parts of your vehicle in an accident, hills, tall buildings, tunnels, weather or wireless phone network congestion. 2-50 Your Responsibility You may need to increase the volume of your radio to hear the OnStar advisor. If the light next to the OnStar buttons is red, this means that your system is not functioning properly and should be checked by a dealer. If the light appears clear (no light is appearing), your OnStar subscription has expired. You can always press the blue OnStar button to conﬁrm that your OnStar equipment is active. Universal Home Remote System The Universal Home Remote System provides a way to replace up to three hand-held radio-frequency (RF) transmitters used to activate devices such as garage door openers, security systems, and home lighting. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. The FCC Grant of Equipment Authorization Certiﬁcate number is CB2SAHL3. This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference received, including interference that may cause undesired operation of the device. The Canadian Registration ID number is 2791021849A. Changes or modiﬁcations to this system by other than an authorized service facility could void authorization to use this equipment. 2-51 Read the instructions completely before attempting to program the Universal Home Remote. Because of the steps involved, it may be helpful to have another person available to assist you in the programming the Universal Home Remote. Keep the original hand-held transmitter for use in other vehicles as well as for future Universal Home Remote programming. It is also recommended that upon the sale of the vehicle, the programmed Universal Home Remote buttons should be erased for security purposes. See “Erasing Universal Home Remote Buttons” later in this section. When programming a garage door, park outside of the garage. Park directly in line with and facing the garage door opener motor-head or gate motor-head. Be sure that people and objects are clear of the garage door or gate you are programming. It is recommended that a new battery be installed in your hand-held transmitter for quicker and more accurate transmission of the radio-frequency signal. Universal Home Remote System Operation (With One Triangular LED) If there is one triangular Light Emitting Diode (LED) indicator light above the Universal Home Remote buttons, follow the instructions below. This system provides a way to replace up to three remote control transmitters used to activate devices such as garage door openers, security systems, and home automation devices. Do not use the Universal Home Remote with any garage door opener that does not have the stop and reverse feature. This includes any garage door opener model manufactured before April 1, 1982. 2-52 Programming the Universal Home Remote System If you have questions or need help programming the Universal Home Remote System, call 1-800-355-3515 or go to www.homelink.com. Programming a garage door opener involves time-sensitive actions, so read the entire procedure before you begin. If you do not follow these actions, the device will time out and you will have to repeat the procedure. To program up to three devices: 1. From inside the vehicle, press and hold down the two outside buttons at the same time, releasing only when the Universal Home Remote indicator light begins to ﬂash, after 20 seconds. This step will erase the factory settings or all previously programmed buttons. Do not hold down the buttons for longer than 30 seconds and do not repeat this step to program the remaining two Universal Home Remote buttons. 2. Hold the end of your hand-held transmitter about 1 to 3 inches (3 to 8 cm) away from the Universal Home Remote buttons while keeping the indicator light in view. The hand-held transmitter was supplied by the manufacturer of your garage door opener receiver (motor head unit). 3. At the same time, press and hold both the Universal Home Remote button that you would like to use to control the garage door and the hand-held transmitter button. Do not release the Universal Home Remote button or the hand-held transmitter button until Step 4 has been completed. Some entry gates and garage door openers may require you to substitute Step 3 with the procedure noted in “Gate Operator and Canadian Programming” later in this section. 4. The indicator light on the Universal Home Remote will ﬂash slowly at ﬁrst and then rapidly after Universal Home Remote successfully receives the frequency signal from the hand-held transmitter. Release both buttons. 2-53 5. Press and hold the newly-trained Universal Home Remote button and observe the indicator light. If the indicator light stays on continuously, the programming is complete and your garage door should move when the Universal Home Remote button is pressed and released. You do not need to continue the programming Steps 6 through 8 and can stop here. If the Universal Home Remote indicator light blinks rapidly for two seconds and then turns to a constant light, continue with the programming Steps 6 through 8. It may be helpful to have another person available to assist with the remaining steps. 2-54 6. After Steps 1 through 5 have been completed, locate inside the garage the garage door opener receiver (motor-head unit). Locate the “Learn” or “Smart” button. The name and color of the button may vary by manufacturer. 7. Firmly press and release the “Learn” or “Smart” button. After you press this button, you will have 30 seconds to complete Step 8. 8. Immediately return to the vehicle. Firmly press and hold the Universal Home Remote button, chosen in Step 3 to control the garage door, for two seconds, and then release it. If the garage door does not move, press and hold the same button a second time for two seconds, and then release it. Again, if the door does not move, press and hold the same button a third time for two seconds, and then release. The Universal Home Remote should now activate the garage door. To program the remaining two Universal Home Remote buttons, begin with Step 2 of “Programming the Universal Home Remote System.” Do not repeat Step 1, as this will erase all previous programming from the Universal Home Remote buttons. Gate Operator and Canadian Programming If you have questions or need help programming the Universal Home Remote System, call 1-800-355-3515 or go to www.homelink.com. Canadian radio-frequency laws require transmitter signals to time out or quit after several seconds of transmission. This may not be long enough for Universal Home Remote to pick up the signal during programming. Similarly, some U.S. gate operators are manufactured to time out in the same manner. If you live in Canada, or you are having difficulty programming a gate operator or garage door opener by using the “Programming Universal Home Remote” procedures, regardless of where you live, replace Step 3 under “Programming Universal Home Remote” with the following: Continue to press and hold the Universal Home Remote button while you press and release every two seconds (cycle) the hand-held transmitter button until the frequency signal has been successfully accepted by the Universal Home Remote. The Universal Home Remote indicator light will ﬂash slowly at ﬁrst and then rapidly. Proceed with Step 4 under “Programming Universal Home Remote” to complete. 2-55 Using Universal Home Remote Press and hold the appropriate Universal Home Remote button for at least half of a second. The indicator light will come on while the signal is being transmitted. Erasing Universal Home Remote Buttons Erase the programmed buttons when you sell or terminate your lease. To erase all programmed buttons on the Universal Home Remote device: Reprogramming a Single Universal Home Remote Button To reprogram any of the three Universal Home Remote buttons, repeat the programming instructions earlier in this section, beginning with Step 2. For help or information on the Universal Home Remote System, call the customer assistance phone number under Customer Assistance Offices on page 7-5. Storage Areas Glove Box Open the glove box by pulling the bottom of the handle upward. Cupholder(s) Your vehicle may have two cupholders in front of the front armrest storage area. You may also have a cupholder in the center of the rear bench seat. Pull down on the lid to open the cupholder. 1. Press and hold down the two outside buttons until the indicator light begins to ﬂash, after 20 seconds. 2. Release both buttons. 2-56 Front Seat Storage Net Your vehicle has storage nets located on the back of the front seats. To remove these nets, pull out on each of the four clips located on the net. Front Armrest Storage Area Your vehicle has a front armrest storage area. To open, lift the latch on the front of the armrest and pull up. Luggage Carrier If your vehicle has this feature, you can load cargo on your vehicle. The luggage carrier consists of siderails attached to the roof. The crossrails attach into the siderails and can be moved back and forth to accommodate various cargo sizes. Notice: Loading cargo on the luggage carrier that weighs more than 250 lbs. (113 kg) or hangs over the rear or sides of the vehicle may damage your vehicle. Load cargo only on top of the crossrails and tie the cargo down to the crossrail support cargo tie-down loops, making sure to fasten it securely Do not exceed the maximum vehicle capacity when loading your vehicle. For more information on vehicle capacity and loading, see Loading Your Vehicle on page 4-42. Adjusting the Crossrails To adjust the crossrails to ﬁt your load: 1. Use the provided crossrail key to unlock the crossrail end cap by turning it counterclockwise. 2-57 2. Remove the end cap. 2-58 3. Pull the lever labeled “PULL” from left to right to loosen the crossrail. 4. Repeat Steps 1 through 3 to the opposite end of the crossrail. 5. Once both sides of the crossrail are loose, adjust the crossrail to the desired position. 6. Push the lever labeled “PULL” from right to left to lock the crossrail in place. 7. Reinstall end cap and lock by turning the key clockwise. 8. Repeat Steps 5 through 7 to the opposite end of the crossrail. Stop Tabs If your vehicle has a sunroof, it will have a crossrail stop tab placed in the siderail. This tab prevents you from moving the crossrails past the opening of the sunroof and loading cargo too far forward. Your vehicle may have cargo tie downs. Once you load the cargo onto the crossrails, secure it by tying it down to the cargo tie downs. Do not load cargo directly on the roof of your vehicle. See Cargo Tie Downs on page 2-59 for more information. Rear Storage Area Your vehicle has a rear storage area located on the passenger’s side of the cargo area. To open, pull the two tabs out and open lid. Convenience Net Your vehicle may have a convenience net in the rear of the vehicle. Put small loads behind the net. The net is not for heavier loads. Store them as far forward as you can. If you put items onto the cargo cover, the Cargo Cover Notice: weight of the items could cause the attachment clips to break. You would no longer be able to attach and use the cargo cover. The repairs would not be covered by your warranty. Never put anything on top of the cargo cover. If your vehicle has a cargo cover, you can use it to cover items in the rear of the vehicle. Remove the cover from its pouch and place the loops found on each corner of the cover, over the two pegs in each corner of the rear if the vehicle. When it is not in use, fold up the cover and return it to the pouch. Cargo Tie Downs Your vehicle may have four cargo tie-downs. These tie-downs are located in tracks on the roof of the vehicle. Each tie-down can be moved to anywhere on the track. To loosen, turn the tie-down counterclockwise until it moves freely in the track. To tighten, turn the tie-down clockwise. 2-59 Vent: With the sunroof closed, press and hold the front of the switch to vent the sunroof. To stop the sunroof before it reaches its full vent position, release the switch. Press and hold the back of the switch to close. Do not keep the sunroof open for long periods of time. Debris may collect in the tracks. Sunshade Operation The sunshade automatically opens with the sunroof, but can be manually pulled shut after the sunroof is closed. To adjust the sunshade, push it backward or pull it forward to the desired position. The sunshade cannot be adjusted further than the current closed position of the sunroof. Sunroof To operate a power sliding sunroof, the ignition must be on, or Retained Accessory Power (RAP) must be active. See Retained Accessory Power (RAP) on page 2-20. The switch used to operate the sunroof is located in the headliner. Open/Close: Press and release the back of the switch to fully open the sunroof. If the sunshade is in the closed position, it automatically opens with the sunroof. To stop the sunroof before it reaches the full open position press and release the front or back of the switch. An air deﬂector raises when the sunroof is fully opened. Press the front of the switch to close the sunroof. 2-60 Section 3 Instrument Panel Instrument Panel Overview ...............................3-4 Hazard Warning Flashers ................................3-6 Other Warning Devices ...................................3-6 Horn .............................................................3-6 Tilt Wheel .....................................................3-7 Turn Signal/Multifunction Lever .........................3-7 Turn and Lane-Change Signals ........................3-8 Headlamp High/Low-Beam Changer ..................3-9 Flash-to-Pass .................................................3-9 Windshield Wipers ........................................3-10 Windshield Washer .......................................3-10 Rear Window Wiper/Washer ...........................3-11 Cruise Control ..............................................3-11 Exterior Lamps .............................................3-15 Headlamps on Reminder ................................3-16 Daytime Running Lamps (DRL) .......................3-17 Automatic Headlamp System ..........................3-17 Off-Road Lamps ...........................................3-18 Fog Lamps ..................................................3-19 Instrument Panel Brightness ...........................3-19 Dome Lamp .................................................3-19 Dome Lamp Override ....................................3-20 Exit Lighting .................................................3-20 Reading Lamps ............................................3-20 Electric Power Management ...........................3-20 Battery Run-Down Protection ..........................3-20 Accessory Power Outlet(s) .............................3-21 Ashtray(s) and Cigarette Lighter ......................3-22 Climate Controls ............................................3-22 Climate Control System .................................3-22 Outlet Adjustment .........................................3-24 Warning Lights, Gages, and Indicators ............3-25 Instrument Panel Cluster ................................3-26 Speedometer and Odometer ...........................3-27 Trip Odometer ..............................................3-27 Tachometer .................................................3-27 Safety Belt Reminders ...................................3-28 Airbag Readiness Light ..................................3-29 Passenger Airbag Status Indicator ...................3-30 Charging System Light ..................................3-32 Up-Shift Light ...............................................3-32 Brake System Warning Light ..........................3-33 Antilock Brake System Warning Light ...............3-34 Traction Off Light ..........................................3-34 StabiliTrak® Not Ready Light ..........................3-34 Engine Coolant Temperature Gage ..................3-35 Tire Pressure Light .......................................3-35 3-1 Section 3 Instrument Panel Malfunction Indicator Lamp .............................3-36 Oil Pressure Light .........................................3-38 Security Light ...............................................3-39 Cruise Control Light ......................................3-39 Highbeam On Light .......................................3-39 Fuel Gage ...................................................3-40 Driver Information Center (DIC) .......................3-40 DIC Operation and Displays ...........................3-40 DIC Warnings and Messages .........................3-43 Audio System(s) .............................................3-48 Setting the Time ...........................................3-48 Radio(s) ......................................................3-49 XM Radio Messages .....................................3-60 Navigation/Radio System ...............................3-61 Theft-Deterrent Feature ..................................3-61 Radio Reception ...........................................3-61 Fixed Mast Antenna ......................................3-62 XM™ Satellite Radio Antenna System .............3-62 3-2 ✍ NOTES 3-3 Instrument Panel Overview Automatic Transmission shown, Manual Transmission similar 3-4 The main components of your instrument panel are the following: H. Parking Brake Release. See Parking Brake on page 2-32. I. Audio System. See Audio System(s) on page 3-48. J. Climate Control System. See Climate Control System on page 3-22. K. Rear Washer/Wiper Control. See Rear Window Wiper/Washer on page 3-11. L. Off-Road Lamps Buttons. See Off-Road Lamps on page 3-18. M. Shift Lever. See Automatic Transmission Operation on page 2-23 or Manual Transmission Operation on page 2-26. N. Accessory Power Outlets. See Accessory Power Outlet(s) on page 3-21. O. Glove Box. See Glove Box on page 2-56. A. Air Outlets. See Outlet Adjustment on page 3-24. B. Turn Signal/Multifunction Lever. See Turn Signal/ Multifunction Lever on page 3-7. Windshield Washer/Wiper. See Windshield Wipers on page 3-10 and Windshield Washer on page 3-10. Cruise Controls. See Cruise Control on page 3-11. C. Horn. See Horn on page 3-6. D. Instrument Panel Cluster. See Instrument Panel Cluster on page 3-26. E. Hazard Warning Flasher Button. See Hazard Warning Flashers on page 3-6. F. All-Wheel Drive, Passenger Air Bag Status Indicator, Locking Rear Axle, and Traction Control System/ StabiliTrak® Buttons. See Full-Time Four-Wheel Drive on page 2-27,Passenger Airbag Status Indicator on page 3-30, Locking Rear Axle on page 4-6, Traction Control System (TCS) on page 4-5 and StabiliTrak® System on page 4-7. G. Exterior Lamps Control, Dome Override Button, Instrument Panel Brightness Control, Fog Lamp Button, and OnStar® Button. See Exterior Lamps on page 3-15, Dome Lamp Override on page 3-20, Instrument Panel Brightness on page 3-19, Fog Lamps on page 3-19, and OnStar® System on page 2-48. 3-5 Hazard Warning Flashers The hazard warning ﬂashers let you warn the police and others that you have a problem. The front and rear turn signal lamps will ﬂash on and off. The hazard warning ﬂasher button is located towards the center of the instrument panel. Press the button to make the front and rear turn signal lamps ﬂash on and off. Press the button again to turn the ﬂashers off. While the hazard warning ﬂashers are on, the turn signals do not work. The hazard warning ﬂashers work no matter what position the key is in, and even if the key is not in the ignition switch. Other Warning Devices If you carry reﬂective triangles, you can set one up at the side of the road about 300 feet (100 m) behind your vehicle. Horn To sound the horn, press the horn symbol on the steering wheel pad. 3-6 Tilt Wheel A tilt wheel allows the steering wheel to be adjusted before driving. It can be raised to allow more room for the driver to enter and exit the vehicle. Turn Signal/Multifunction Lever The tilt lever is located on the left side of the steering column, under the turn signal lever. To tilt, hold the steering wheel and pull the tilt lever toward you. Move the wheel to a comfortable level, then release the tilt lever to lock the wheel in place. Do not adjust the steering wheel while driving. The lever on the left side of the steering column includes the following: (cid:129) G Turn and Lane Change Signals. See Turn Signal/Multifunction Lever on page 3-7. (cid:129) 53 Headlamp High/Low-Beam Changer. See Headlamp High/Low-Beam Changer on page 3-9. Flash-to-Pass. See Flash-to-Pass on page 3-9. (cid:129) N Windshield Wipers. See Windshield Wipers on page 3-10. (cid:129) L Windshield Washer. See Windshield Washer (cid:129) J Cruise Control. See Cruise Control on on page 3-10. page 3-11. 3-7 (cid:129) Turn and Lane-Change Signals The turn signal has one upward (for right) and one downward (for left) positions. These positions allow you to signal a turn or a lane change. To signal a turn, move the lever all the way up or down. When the turn is ﬁnished, the lever will automatically return to the off position. To signal a lane change, raise or lower the lever until the arrow starts to ﬂash. Hold it there until the change is completed. The lever will return by itself when released. An arrow on the instrument panel cluster will ﬂash in the direction of the turn or lane change. As you signal a turn or a lane change, if the arrows ﬂash more quickly than normal, a signal bulb may be burned out and other drivers will not see your vehicle’s turn signal. If a bulb is burned out, replace it to help avoid an accident. If the arrows do not go on at all when signaling a turn, check for a burned-out bulb or a blown fuse. For bulb replacement, see Taillamps, Turn Signal, Stoplamps and Back-up Lamps on page 5-50. For a blown fuse or circuit breaker, see Fuses and Circuit Breakers on page 5-102 Turn Signal On Chime If a turn signal is left on for more than 3/4 of a mile (1.2 km), a chime will sound at each ﬂash of the turn signal and the message TURN SIGNAL will also appear in the DIC. To turn the chime and message off, move the turn signal lever to the off position. See “TURN SIGNAL” under DIC Warnings and Messages on page 3-43 DIC Warnings and Messages for more information. 3-8 Headlamp High/Low-Beam Changer 53(Headlamp High/Low Beam Changer): To change the headlamps from low to high beam, push the lever toward the instrument panel. To return to low-beam headlamps, pull the multifunction lever toward you. Then release it. When the high beams are on, this indicator light on the instrument panel cluster will also be on. Flash-to-Pass This feature lets you use the high-beam headlamps to signal a driver in front of you that you want to pass. It works even if the headlamps are in the automatic position. To use it, pull the turn signal lever toward you, then release it. If your headlamps are in the automatic position or on low beam, your high-beam headlamps will turn on. They will stay on as long as you hold the lever toward you. The high-beam indicator on the instrument panel cluster will come on. Release the lever to return to normal operation. 3-9 Windshield wipers work in all power modes, except when set to LOCK. After the engine is turned off, wipers will work in Retained Accessory Power (RAP) mode until a door is opened. See Retained Accessory Power (RAP) on page 2-20. Windshield Washer L (Washer Fluid): There is a paddle marked with the windshield washer symbol at the top of the multifunction lever. To spray washer ﬂuid on the windshield, push the paddle. The wipers will clear the window and then either stop or return to your preset speed. {CAUTION: In freezing weather, do not use your washer until the windshield is warmed. Otherwise the washer ﬂuid can form ice on the windshield, blocking your vision. Windshield Wipers You control the windshield wipers by turning the band with the wiper symbol on it. 8(Mist): Turn the band to mist for a single wiping cycle. Hold it there until the wipers start. Then let go. The wipers will stop after one wipe. Hold the band on mist longer, if more wipes are needed. N (Delay): The wiper speed can be set for long or short delays between wipes. This can be very useful in light rain or snow. Turn the band to choose the delay time. The closer to the top of the lever, the shorter the delay. 6 (Low Speed): For steady wiping at low speed, turn the band away from you to the ﬁrst solid position past the delay settings. 1 (High Speed): For high-speed wiping, turn the band to the second solid position past the delay settings. 9(Off): Move the band to off, to stop the wipers. Be sure to clear ice and snow from the wiper blades before using them. If they are frozen to the windshield, carefully loosen or thaw them. If your blades do become worn or damaged, get new blades or blade inserts. 3-10 Rear Window Wiper/Washer This knob is located on the instrument panel below the climate controls. Cruise Control With cruise control, you can maintain a speed of about 25 mph (40 km/h) or more without keeping your foot on the accelerator. This can really help on long trips. Cruise control does not work at speeds below about 25 mph (40 km/h). 9(Off): This position turns the system off. Z (Rear Wiper): Turn the knob to 1 for a slower wiping speed or to 2 for a faster wiping speed. 0 (Off): Turn the knob to 0 for off. =(Washer Fluid): To wash and wipe the window, press the button within the knob with this symbol. The rear window washer uses the same ﬂuid bottle as the windshield washer. However, the rear window washer will run out of ﬂuid before the windshield washer. If the windshield can be washed, but not the rear windows, check the ﬂuid level. R (On): This position activates the system. + (Resume/Accelerate): Move the lever to this symbol to make the vehicle accelerate or resume to a previously set speed. rT (Set): Press this button to set the speed. 3-11 Cruise control will not work if your parking brake is set, or if the master cylinder brake ﬂuid level is low. If you apply your brakes, the cruise control shuts off. Setting Cruise Control {CAUTION: {CAUTION: Cruise control can be dangerous where you cannot drive safely at a steady speed. So, do not use your cruise control on winding roads or in heavy traffic. Cruise control can be dangerous on slippery roads. On such roads, fast changes in tire traction can cause excessive wheel slip, and you could lose control. Do not use cruise control on slippery roads. The cruise control disengages, if the vehicle has the Traction Control System (TCS) and it begins to limit wheel spin. See Traction Control System (TCS) on page 4-5. When road conditions allow you to safely use it again, you can turn cruise control back on. If you leave your cruise control on when you are not using cruise, you might hit a button and go into cruise when you do not want to. You could be startled and even lose control. Keep the cruise control switch off until you want to use cruise control. 1. Move the cruise control switch to on. 2. Get up to the speed desired. 3. Press in the set button at the end of the lever and release it. 4. Take your foot off the accelerator pedal. The cruise symbol on the instrument panel comes on when the cruise control is engaged. 3-12 Resuming a Set Speed Suppose you set your cruise control at a desired speed and then you apply the brake or step on the clutch. This, of course, disengages the cruise control. But you do not need to reset it. Once you are going about 25 mph (40 km/h) or more, you can move the cruise control switch brieﬂy from on to resume/accelerate. The vehicle will go back to the chosen speed and stays there. If you hold the switch at resume/accelerate the vehicle will keep going faster until you release the switch or apply the brake. Do not hold the switch at resume/ accelerate, unless you want the vehicle to go faster. Increasing Speed While Using Cruise Control There are two ways to go to a higher speed: (cid:129) Use the accelerator pedal to get to the higher speed. Press the set button at the end of the lever, then release the button and the accelerator pedal. You will now cruise at the higher speed. If the accelerator pedal is held longer than 60 seconds, cruise control will turn off. (cid:129) Move the cruise switch from on to resume/ accelerate. Hold it there until you get up to the speed you want, and then release the switch. To increase your speed in very small amounts, move the switch brieﬂy to resume/accelerate. Each time you do this, your vehicle goes about 1 mph (1.6 km/h) faster. 3-13 Reducing Speed While Using Cruise Control (cid:129) Press and hold the set button until you reach the desired lower speed, then release it. To slow down in very small amounts, brieﬂy press the set button. Each time you do this, you will go about 1 mph (1.6 km/h) slower. Passing Another Vehicle While Using Cruise Control Use the accelerator pedal to increase your speed. When you take your foot off the pedal, your vehicle slows down to the cruise control speed you set earlier. Using Cruise Control on Hills How well your cruise control works on hills depends upon your speed, load, and the steepness of the hills. When going up steep hills, you might want to step on the accelerator pedal to maintain the vehicle speed. When going downhill, you might have to brake or shift to a lower gear to keep the vehicle speed down. Of course, applying the brake turns off the cruise control. Many drivers ﬁnd this to be too much trouble and do not use cruise control on steep hills. Ending Cruise Control To turn off the cruise control, do one of the following: (cid:129) Step lightly on the brake pedal. (cid:129) Move the cruise control switch to off. Lightly tap or press the clutch, if you have a manual transmission. Erasing Speed Memory When you turn off the cruise control or the ignition, the cruise control set speed memory is erased. 3-14 (cid:129) (cid:129) Exterior Lamps The control on the driver’s side of your instrument panel operates the exterior lamps. O (Exterior Lamps): Turn the knob, located to the right of this symbol, to choose one of the four exterior lamp positions. O (Off): Turn the knob to this position to turn off all exterior lamps, including the Daytime Running Lamps (DRL). This is a momentary control that springs back to AUTO when released. Vehicles ﬁrst sold in Canada do not have the DRL disable feature available. Vehicles ﬁrst sold in Canada cannot turn off the DRL unless the following conditions are met: The vehicle has an automatic transmission. The gear position is in PARK (P). The headlamp switch is turned to the Off position. AUTO (Automatic): Turn the knob to this position to automatically turn on the headlamps at normal brightness, together with the following: (cid:129) Sidemarker Lamps Taillamps (cid:129) Parking Lamps Instrument Panel Lights Due to the momentary switch design, the automatic headlamps may be disabled even if the control is in the AUTO position. To enable automatic lighting, do any of the following: Turn the headlamp control from AUTO to off and release the control. It will return back to the AUTO position by itself. Turn the headlamp control from the parking lamp or headlamp position to AUTO. 3-15 (cid:129) (cid:129) (cid:129) (cid:129) (cid:129) (cid:129) (cid:129) To disable automatic lighting, do any of the following: Turn the headlamp control from AUTO to off and release the control. It will return back to the AUTO position by itself. Turn the headlamp control from AUTO to the parking lamp or headlamp position. See Automatic Headlamp System on page 3-17 for more information. Vehicles ﬁrst sold in Canada with an automatic transmission cannot turn off automatic headlamps unless the gear position is in PARK (P) and the headlamp switch is turned to the Off position. Vehicles ﬁrst sold in Canada with a manual transmission can turn off the automatic headlamps with the headlamp control; however, the parking lamps will remain on. ;(Parking Lamps): Turn the knob to this position to turn on the parking lamps, together with the following: (cid:129) Sidemarker Lamps Taillamps License Plate Lamps Instrument Panel Lights 2(Headlamps): Turn the knob to this position to turn on the headlamps, together with the previously listed lamps and lights. The headlamps can be switched from low to high beam by pushing the turn signal/multifunction lever toward the instrument panel. Headlamps on Reminder A headlamp reminder chime will sound if the following conditions are met: The driver door is open. (cid:129) Parking lamps or headlamps are manually turned on. The key is either not in the ignition switch, or it is in the LOCK position of the ignition switch. The headlamp reminder cannot be turned off if the conditions listed above are met. In the automatic mode, the headlamps turn off once the ignition is in ACC. 3-16 (cid:129) (cid:129) (cid:129) (cid:129) (cid:129) (cid:129) (cid:129) Daytime Running Lamps (DRL) Daytime Running Lamps (DRL) can make it easier for others to see the front of your vehicle during the day. DRL can be helpful in many different driving conditions, but they can be especially helpful in the short periods after dawn and before sunset. Fully functional daytime running lamps are required on all vehicles ﬁrst sold in Canada. The DRL system will come on when the following conditions are met: The ignition is on. The exterior lamps control is in AUTO. The transmission is not in PARK (P) if you have an automatic transmission. The light sensor determines it is daytime. When the DRL are on, no other lamps are on. The instrument panel will not be lit up either. For vehicles ﬁrst sold in Canada, if parking lamps are manually turned on, DRL will stay on. When it begins to get dark, the automatic headlamp system will switch from DRL to the headlamps. As with any vehicle, you should turn on the regular headlamp system when you need it. To turn off the DRL, see Exterior Lamps on page 3-15. Vehicles ﬁrst sold in Canada cannot turn off DRL unless certain conditions are met. See Exterior Lamps on page 3-15. Automatic Headlamp System When it is dark enough outside, the automatic headlamp system will turn on after the transmission has been shifted from PARK (P) to DRIVE (D). The headlamps, taillamps, sidemarker, parking lamps, roof marker lamps, and the instrument panel lights will turn on at normal brightness. The radio lights will become more dim when the headlights are off compared to when the headlights are on. Your vehicle has a light sensor located on the top of the instrument panel. Be sure it is not covered, or the system will be on whenever the ignition is on. The system may also turn on the headlamps when driving through a parking garage, heavy overcast weather, or a tunnel. This is normal. There is a delay in the transition between the daytime and nighttime operation of the Daytime Running Lamps (DRL) and the automatic headlamp system so that driving under bridges or bright overhead street lights does not affect the system. The DRL and automatic headlamp system will only be affected when the light sensor detects a change in lighting lasting longer than the delay. 3-17 (cid:129) (cid:129) (cid:129) (cid:129) If you start your vehicle in a dark garage, the automatic headlamp system will come on immediately. Once you leave the garage, it will take about one minute for the automatic headlamp system to change to DRL if it is light outside. During that delay, the instrument panel cluster may not be as bright as usual. Make sure the instrument panel brightness control is in the full bright position. See Instrument Panel Brightness on page 3-19. Off-Road Lamps The off-road lamps, if the vehicle has them, provide auxiliary lighting when the vehicle is used off road. These lamps are not intended to be used in place of existing vehicle lighting. The lamps are not to be used on any public street or highway and are to be covered when not in use. Check your state and local laws before installing or using any auxiliary lighting. In some states it may be necessary to remove the roof lamps when operating the vehicle on the highway. 3-18 Roof Mounted Off-Road Light Switch Lower Grille Off-Road Light Switch The switches for the off-road lamps are located in the center of the instrument panel below the climate controls. One switch is used for the front lower-grille mounted off-road lamps, if the vehicle has them, and the other switch is used for the roof-mounted off-road lamps, if the vehicle has them. To use the lamps, remove the covers from the lamps and press the switch to turn them on or off. An indicator light on the switch will turn on when the lamps are on. Notice: Turning on the off-road lamps before removing the lamp covers could damage the off-road lamps and the covers. Always remove the covers before turning on the off-road lamps. The off-road lamps remain on even after the ignition is turned off. The off-road lamp switch must be pressed to turn them off. Fog Lamps Your vehicle has fog lamps. You can use them for better vision in foggy or misty conditions. Your parking lamps and/or low-beam headlamps must be on for your fog lamps to work. The fog lamp button is located in the exterior lamps control. Press the button to turn the fog lamps on while the headlamps or parking lamps are on. Press the button again to turn them off. An indicator light will glow in the button when the fog lamps are on. Remember, fog lamps alone will not give off as much light as your headlamps. Never use your fog lamps in the dark without turning on the headlamps. The fog lamps will go off whenever your high-beam headlamps come on. When the high beams go off, the fog lamps will come on again. Some localities have laws that require the headlamps to be on along with the fog lamps. Instrument Panel Brightness D (Instrument Panel Brightness): This feature controls the brightness of the instrument panel lights. The thumbwheel for this feature is located next to the exterior lamp control. Turn the thumbwheel up or down to brighten or dim the instrument panel lights and the radio display. The instrument panel lights, cluster, and radio display do not dim to complete darkness. Turn the thumbwheel all the way up to turn the dome lamps on. Dome Lamp The dome and footwell lamps come on when any door is opened. The dome lamps are located in the cargo and front area of the vehicle. The dome and footwell lamps can be turned on by turning the thumbwheel, located next to the exterior lamps control, all the way up. In this position, the lamps remain on whether a door is opened or closed. 3-19 Dome Lamp Override E (Dome Lamp Override): You can use the dome override button, located below the exterior lamps control, to set the dome and footwell lamps to come on automatically when a door is opened, or to remain off. To turn the lamps off, press the button into the in position. With the button in this position, the dome lamps will remain off when the doors are open. To return the lamps to automatic operation, press the button again and return it to the out position. With the button in this position, the dome lamps will come on when you open a door. Exit Lighting With exit lighting, the interior lamps will come on when you remove the key from the ignition. The lamps will not come on if the dome override button is pressed in. Reading Lamps Your vehicle has reading lamps. Press the button located next to the lamp to turn them on or off. These lamps will not come on with the dome lamps. 3-20 Electric Power Management The vehicle has Electric Power Management (EPM) that estimates the battery’s temperature and state of charge. It then adjusts the voltage for best performance and extended life of the battery. When the battery’s state of charge is low, the voltage is raised slightly to quickly put the charge back in. When the state of charge is high, the voltage is lowered slightly to prevent overcharging. If the vehicle has a voltmeter gage, you may see the voltage move up or down. This is normal. If there is a problem, an alert will be displayed. The battery can be discharged at idle if the electrical loads are very high. This is true for all vehicles. This is because the generator (alternator) may not be spinning fast enough at idle to produce all the power that is needed for very high electrical loads. A high electrical load occurs when several of the following loads are on: headlamps, high beams, fog lamps, rear window defogger, climate control fan at high speed, heated seats, engine cooling fans, trailer loads, and loads plugged into accessory power outlets. Battery Run-Down Protection This feature shuts off the dome lamp if it is left on for more than 20 minutes when the ignition is in LOCK. This will help prevent your battery from running down. Accessory Power Outlet(s) Your vehicle has accessory power outlets. With accessory power outlets you can plug in auxiliary electrical equipment such as a cellular telephone or CB radio. Your vehicle has two accessory power outlets located on the lower part of the instrument panel below the climate control system and there may be one located in the rear cargo area. A small cap must be pulled down to access an accessory power outlet. When not using an outlet, be sure to cover it with the protective cap. Notice: Leaving electrical equipment on for extended periods will drain the battery. Always unplug electrical equipment when not in use and do not plug in equipment that exceeds the maximum amperage rating of 20 amperes. Certain electrical accessories may not be compatible with the accessory power outlet and could result in blown vehicle or adapter fuses. If you experience a problem, see your dealer for additional information on accessory power outlets. Notice: Adding any electrical equipment to your vehicle may damage it or keep other components from working as they should. The repairs would not be covered by your warranty. Do not use equipment exceeding maximum amperage rating of 20 amperes. Check with your dealer/retailer before adding electrical equipment. When adding electrical equipment, be sure to follow the proper installation instructions included with the equipment. Notice: damage not covered by your warranty. Do not hang any type of accessory or accessory bracket from the plug because the power outlets are designed for accessory power plugs only. Improper use of the power outlet can cause 3-21 If you put papers, pins, or other ﬂammable Ashtray(s) and Cigarette Lighter Your vehicle may have an ashtray and cigarette lighter. Your ashtray is located in your center console area. The ashtray can be removed for cleaning. When the ashtray is removed, this area can also be used as a cupholder. Notice: items in the ashtray, hot cigarettes or other smoking materials could ignite them and possibly damage your vehicle. Never put ﬂammable items in the ashtray. To use the lighter, press it in all the way, and let go. When it’s ready, it will pop back out by itself. Notice: Holding a cigarette lighter in while it is heating does not let the lighter back away from the heating element when it is hot. Damage from overheating can occur to the lighter or heating element, or a fuse could be blown. Do not hold a cigarette lighter in while it is heating. 3-22 Climate Controls Climate Control System The heating, cooling, and ventilation of the vehicle can be controlled with this system. Temperature: Turn the left knob on the control panel to adjust the temperature of the air in the vehicle. Turn the knob clockwise or counterclockwise to increase or decrease the temperature. #(Air Conditioning): Press the center of the left knob on the control panel to turn the air conditioning system on or off. An indicator light on the button will be lit when the air conditioning is turned on. This system cools and dehumidiﬁes the air entering the vehicle. The air conditioning will not function if the fan is turned off. If air conditioning is selected with fan off, the indicator light ﬂashes three times and then turns off. this button to turn the recirculation mode on or off. An indicator light on the button comes on to show that the recirculation mode is activated. A slight change in engine performance may occur when the air conditioning compressor shuts off and turns on again. This is normal. The system is designed to make adjustments to help with fuel economy while still maintaining the selected temperature. The air conditioning system removes moisture from the air, so sometimes there may be a small amount of water dripping underneath the vehicle while idling or after turning off the engine. This is normal. 9(Fan): Turn the center knob on the control panel to control the fan speed. Turn the knob clockwise or counterclockwise to increase or decrease the fan speed. 9(Off): Turn the center knob to this position to turn the fan off. With the fan off, you may still experience airﬂow from the system that increases with vehicle speed depending on the mode and temperature settings. Enable recirculation mode to stop this airﬂow from occurring. @ (Recirculation): Press the center of the fan control knob to recirculate air inside the vehicle and prevent outside air from coming in. It can be used to prevent outside odors from entering the vehicle and cool the air inside the vehicle more quickly. Press Recirculation is available in the bi-level, and vent modes. Recirculation is not available while in ﬂoor, ﬂoor/defog and defrost mode. If recirculation is selected in these modes, the indicator ﬂashes three times indicating it is not available in that mode. When the recirculation mode is turned on, the air conditioning turns on automatically. When it is hot enough outside, the recirculation mode may turn on automatically to help improve cooling performance. The indicator light will be lit to show this mode is active. If the recirculation button is pressed while in this mode, the light will ﬂash three times and stay on to indicate that recirculation may not be shut off. The right knob on the control panel is used to direct the airﬂow inside the vehicle. In-between modes are available by moving the right control knob between modes with symbols. The in-between mode is a combination of the two modes that the control is centered between. Turn the right knob to select one of the following modes: H (Vent): This mode directs air to the instrument panel outlets. 3-23 \(Bi-Level): This mode directs air to the instrument panel outlets, and the remaining air to the ﬂoor outlets and the defroster and side window outlets. Cooler air is directed to the upper outlets and warmer air to the ﬂoor outlets. [(Floor): This mode directs air to the ﬂoor outlets, side window outlets, and defroster. Recirculation is not available in this mode. Defogging and Defrosting Fog on the inside of windows is a result of high humidity (moisture) condensing on the cool window glass. This can be minimized if the climate control system is used properly. There are two modes to clear fog or frost from the windshield and side windows. Use the defog mode to clear the windows of fog or moisture and warm the passengers. Use the defrost mode to remove fog or frost from the windshield more quickly. For best results, clear all snow and ice from the windshield before defrosting. /(Floor/Defog): This mode directs the air to the windshield, the side window outlets, and to the ﬂoor outlets. When this mode is selected, the system runs the air conditioning system unless the outside temperature is near freezing or below. Recirculation is not available in this mode. 3-24 0(Defrost): This mode directs most of the air to the windshield, and the side window outlets. When this mode is selected, the system runs the air conditioning system unless the outside temperature is near or below freezing. Recirculation is not available in this mode. Do not drive the vehicle until all the windows are clear. Rear Window Defogger The rear window defogger uses a warming grid to remove fog or frost from the rear window when the key is in the ignition and turned to ON/RUN. =(Rear Defogger): Press the center of the right knob on the control panel to turn the rear window defogger on or off. First press of this button activates the rear window defogger for 15 minutes and each

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2008 Hummer H3 Owners Manual