2008 Honda S2000 Owners Manual

recommended that you have someone help you remove and install it.

Clean and dry the hardtop before removing it. Store it in your garage or other protected area, and do not stack items on top of it.

78

2008 S2000 ０７／０７／２５　１７：３８：０８　３１Ｓ２Ａ６８０　００８４　

Removable Hardtop

LID

BOLT

BOLT

Installation 1.

Make sure the vehicle is parked on level ground, and that you have adequate clearance above the vehicle.

2.

Loosen the bolt of the rear cover lid with a flat-tipped screwdriver.

3.

Pull the bolt out until it stops against the lid.

CONTINUED

79

2008 S2000 ０７／０７／２５　１７：３８：１６　３１Ｓ２Ａ６８０　００８５　

Removable Hardtop

BOLT

LID

LOCKING LEVER

8.

Make sure the front locking levers are closed.

9.

Make sure the handles for the side lock pins are pivoted forward to the first stop. However, do not pull the handle all the way forward (touching the inside of the top).

4.

Hold the bolt and lid, and remove the lid by pulling them up together as shown in the illustration above.

5.

Repeat the procedure for the lid on the other side.

6.

Keep the lids in the trunk safely.

7.

Move the seats forward.

80

2008 S2000 ０７／０７／２５　１７：３８：２５　３１Ｓ２Ａ６８０　００８６　

Removable Hardtop

TAB

LATCH

LOCK ROD

REAR WINDOW DEFOGGER WIRE

10.

POSITIONING HOLE Carefully set the removable hardtop on the vehicle, making sure the lock rods go into the positioning holes behind each door. Be careful not to pinch your fingers.

Make sure that the lock rods do not damage any part of the vehicle, such as the rear wing spoiler, when you install or remove the hardtop.

11.

LOCKING LEVER Push in the tab on each locking lever and pull the locking lever down.

12.

Push the locking lever forward and set the latch into the windshield header.

13.

Pull back on the locking lever and push it up until it latches. Make sure it is securely latched.

14.

Pivot the lock rods backward to lock down the sides of the hardtop. Make sure the rear window defogger wire is set under the lock rod to ensure the wire is not crushed or entangled.

CONTINUED

81

2008 S2000 ０７／０７／２５　１７：３８：３１　３１Ｓ２Ａ６８０　００８７　

Removable Hardtop

HARNESS

CAP

CONNECTOR

CONNECTOR

Make sure the rear window is clear and you have good visibility before starting to drive.

The defogger wires on the inside of the rear window can be accidentally damaged. When cleaning the glass, always wipe side-to-side.

16.

Plug the harness for the rear window defogger (see page into the rear connector. Make sure it locks into the connector.

61

15.

Remove the cap from the rear window defogger connector.

82

2008 S2000 ０７／０７／２５　１７：３８：４０　３１Ｓ２Ａ６８０　００８８　

Removable Hardtop

Removal

TAB

LATCH

TAB

1.

Lower the windows.

2.

Unplug the rear window defogger harness from the connector by squeezing the tab on the harness plug. Pull on the plug, not the harness.

3.

4.

LOCKING LEVER

LOCKING LEVER

Push in the tab on each locking lever and pull the locking lever down.

5.

With the latches released, pull back on the locking levers and push them up until they latch.

Push the locking levers forward and remove the latches from the windshield header.

CONTINUED

83

2008 S2000 ０７／０７／２５　１７：３８：４７　３１Ｓ２Ａ６８０　００８９　

Removable Hardtop

LOCK ROD

6.

Pivot the lock rods forward to release the sides of the hardtop.

7.

Lift the hardtop straight up off the vehicle and set it aside.

84

8.

Install the cap on the rear defogger connector.

9.

Take the rear cover lids out from the trunk.

Make sure that the lock rods do not damage any part of the vehicle, such as the rear wing spoiler, when you install or remove the hardtop.

2008 S2000 ０７／０７／２５　１７：３８：５４　３１Ｓ２Ａ６８０　００９０　

Removable Hardtop

13.

Lift the wind deflector up (see page

75

).

BOLT

TABS

LID

LID

BOLT

HOLDERS

10.

When reinstalling the rear cover lid, align the tabs to the appropriate holders and push the lid down while holding the bolt out.

11.

Tighten the bolts securely with the flat-tipped screwdriver.

12.

Repeat the procedure for the lid on the other side.

85

2008 S2000 ０７／０７／２５　１７：３８：５９　３１Ｓ２Ａ６８０　００９１　

Removable Hardtop

Storing

Washing

FRONT SEAL

Support the hardtop during storage to prevent the front seal from contacting the floor or any other surface that can deform the rubber.

Avoid automatic car washes that use a high pressure spray.

86

2008 S2000 ０７／０７／２５　１７：３９：０７　３１Ｓ２Ａ６８０　００９２　

TAB

Adjusting the Power Mirrors

SELECTOR SWITCH

Mirrors

4.

When you finish, move the selector switch to the center (off) position. This turns the adjustment switch off to keep your settings.

Keep the inside and outside mirrors clean and adjusted for best visibility. Be sure to adjust the mirrors before you start driving.

The inside mirror has day and night positions. The night position reduces glare from headlights behind you. Flip the tab on the bottom edge of the mirror to select the day or night position.

ADJUSTMENT SWITCH

1.

Turn the ignition switch to the ON (II) position.

2.

3.

Move the selector switch to L (driver’s side) or R (passenger’s side).

Push the appropriate edge of the adjustment switch to move the mirror right, left, up, or down.

87

2008 S2000 ０７／０７／２５　１７：３９：１２　３１Ｓ２Ａ６８０　００９３　

Parking Brake

BUTTON

Driving the vehicle with the parking brake applied can damage the rear brakes and axles. A beeper will sound if the vehicle is driven with the parking brake on.

PARKING BRAKE LEVER

To apply the parking brake, pull the lever up fully. To release it, pull up slightly, push the button, and lower the lever. The parking brake indicator on the instrument panel should go out when the parking brake is fully released (see page

46

).

88

2008 S2000 ０７／０７／２５　１７：３９：１６　３１Ｓ２Ａ６８０　００９４　

Interior Convenience Items

CONSOLE COMPARTMENT

ACCESSORY POWER SOCKET

VANITY MIRROR/SUNVISOR

AUDIO PANEL ＊

DRIVER’S SEAT-BACK POCKET

BEVERAGE HOLDER

DASHBOARD LOWER POCKET

＊

: If equipped

89

2008 S2000 ０７／０７／２５　１７：３９：２４　３１Ｓ２Ａ６８０　００９５　

Interior Convenience Items

Beverage Holder

Accessory Power Socket

Open the beverage holder by pushing on the tab. The lid will slide open.

PARTITION

To hold two cups in the beverage holder, flip the partition up.

Be careful when you are using the beverage holder. A spilled liquid that is very hot can scald you or your passenger. Spilled liquids can also damage the upholstery, carpeting, and electrical components in the interior.

This socket is intended to supply power for 12 volt DC accessories that are rated 120 watts or less (10
amps). It will not power an automotive type cigarette lighter element.

90

2008 S2000 ０７／０７／２５　１７：３９：３２　３１Ｓ２Ａ６８０　００９６　

Console Compartments

Audio Panel

UPPER COMPARTMENT

Interior Convenience Items

LOWER COMPARTMENT

The area between the seats has two compartments. Open the lower compartment by squeezing the handle. Close it with a firm push. You can lock or unlock the lower compartment with the master key.

The lever to open the upper compartment is inside the lower compartment. Push up the lever, and lift the lid. To close, lower the lid, and push it down until it latches.

Ifequipped To open the audio panel, push on the top center, and let the panel swing down. To close, pivot the panel up, and push on it until it latches.

91

2008 S2000 ０７／０７／２５　１７：３９：３９　３１Ｓ２Ａ６８０　００９７　

Interior Convenience Items, Interior Light

Dashboard Lower Pocket

Interior Light

DOOR ACTIVATED

If the switch is in the center position, the interior light will come on when you remove the key from the ignition switch.

SWITCH

The interior light has a three- position switch; ON, Door Activated, and OFF. In the Door Activated (center) position, the light comes on when you:

Open either door. Unlock the doors with the key or the remote transmitter.

The dashboard lower pocket is located next to the audio panel.

92

2008 S2000 ０７／０７／２５　１７：３９：４３　３１Ｓ２Ａ６８０　００９８　

When the switch is in the center position with both doors closed, the two bulbs in the interior light can each be turned on and off with the button next to it.

Interior Light

93

2008 S2000 ０７／０７／２５　１７：３９：４５　３１Ｓ２Ａ６８０　００９９　

94

2008 S2000 ０７／０７／２５　１７：３９：５０　３１Ｓ２Ａ６８０　０１００　

Features

. 96
............... Vents, Heating, and A/C . 100
........................ Vents and Heating . 104
.......... Playing the AM/FM Radio ............ . 107
AM/FM Radio Reception Playing the XM Satellite Radio . 109
. 114
Playing a CD .................................. . 116
CD Changer ................................... . 117
Protecting Your CDs .................... ......... CD Player Error Messages . 120
. 121
CD Changer Error Messages ..... . 122
Remote Audio Controls ................ . 123
Radio Theft Protection ................. ............................... Cruise Control . 124

The heating and air conditioning system in your vehicle provides a comfortable driving environment in all weather conditions.

The standard audio system has many features. This section describes those features and how to use them. (If you have an optional audio system, refer to the operating instructions that came with it.)

Your vehicle has an anti-theft audio system that requires a code number to enable it.

95

2008 S2000 ０７／０７／２５　１７：３９：５３　３１Ｓ２Ａ６８０　０１０１　

Vents, Heating, and A/C

Except S2000 CR model

RECIRCULATION BUTTON

REAR WINDOW DEFOGGER BUTTON

AIR CONDITIONING BUTTON

FAN CONTROL LEVER

96

MODE CONTROL DIAL

TEMPERATURE CONTROL DIAL

2008 S2000 ０７／０７／２５　１７：４０：０９　３１Ｓ２Ａ６８０　０１０２　

Airflow Controls

mode).

Fan Control Lever Push this lever up and down to increase or decrease the fan speed and airflow. The indicators next to the lever show you the speed and airflow selected.

Temperature Control Dial Turning this dial clockwise increases the temperature of the airflow.

Air Conditioning (A/C) Button This button turns the air conditioning on and off. The indicator in the button comes on when the A/C is on.

Recirculation Button When the recirculation indicator is on, air from the vehicle’s interior is sent through the system again (recirculation mode). When the indicator is off, air is brought in from the outside of the vehicle (fresh air

The outside air intakes for the heating and cooling system are at the base of the windshield. Keep this area clear of leaves and other debris.

The system should be left in fresh air mode under almost all conditions. Keeping the system in recirculation mode, particularly with the A/C off, can cause the windows to fog up.

Switch to recirculation mode when driving through dusty or smoky conditions, then return to fresh air mode.

Rear Window Defogger Button This button turns the rear window defogger off and on (see page 61

).

Do not push the defogger button when the convertible top is folded.

Vents, Heating, and A/C

Mode Control Dial Use the mode control dial to select the vents the air flows from. Some air will flow from the dashboard vents in all modes.

Air flows from the vents on both sides of the instrument panel, and from the dashboard vent in front of the passenger.

Airflow is divided between the vents in the dashboard and the floor vents.

Air flows from the center vents in the dashboard above the audio system, the vents on both sides of the instrument panel, and from the floor vents. Select this position when you drive with the convertible top folded.

CONTINUED

97

2008 S2000 ０７／０７／２５　１７：４０：２３　３１Ｓ２Ａ６８０　０１０３　

Vents, Heating, and A/C

Air flows from the floor

vents and the vents on both sides of the instrument panel.

When you select automatically switches to fresh air mode.

, the system

Airflow is divided between

the floor vents and the defroster vents at the base of the windshield, and the vents on both sides of the instrument panel.

Air flows from the defroster

vents at the base of the windshield and the vents on both sides of the instrument panel.

When you select the system automatically switches to fresh air mode and turns on the A/C.

or

98

Ventilation The flow-through ventilation system draws in outside air, circulates it through the interior, then exhausts it through vents behind the seat-backs.

1.

2. 3. 4.

Set the temperature to the lower limit. Make sure the A/C is off. Select Set the fan to the desired speed.

and fresh air mode.

Using the Heater The heater uses engine coolant to warm the air. If the engine is cold, it will be several minutes before you feel warm air coming from the system.

1. 2. 3.

and fresh air mode.

Select Set the fan to the desired speed. Adjust the warmth of the air with the temperature control dial.

Using the A/C Air conditioning places an extra load on the engine. Watch the engine coolant temperature gauge (see page 55
turn off the A/C until the gauge reading returns to normal.

). If it moves near the red zone,

1. 2.

3.

4. 5.

Set the fan to the desired speed. Turn on the A/C by pressing the button. The indicator in the button comes on. Make sure the temperature is set to maximum cool. Select If the outside air is humid, select recirculation mode. If the outside air is dry, select fresh air mode.

you can

Iftheinteriorisverywarm, cool it down more rapidly by partially opening the windows, turning on the A/C, and setting the fan to maximum speed in fresh air mode.

2008 S2000 ０７／０７／２５　１７：４０：３７　３１Ｓ２Ａ６８０　０１０４　

Dehumidify the Interior Air conditioning, as it cools, removes moisture from the air. When used in combination with the heater, it makes the interior warm and dry and can prevent the windows from fogging up.

3.

4.

5.

mode and turns on the A/C. Adjust the temperature so the airflow feels warm. Select rear window. To increase airflow to the windshield, close the corner vents.

to help clear the

1. 2. 3. 4.

Turn the fan on. Turn on the air conditioning. Select Adjust the temperature to your preference.

and fresh air mode.

This setting is suitable for all driving conditions whenever the outside temperature is above 32°F (0°C).

To Defog and Defrost To remove fog from the inside of the windows:

1.

2.

Set the fan to the desired speed, or high for faster defrosting. Select . The system automatically switches to fresh air

or

When you select the system automatically turns on the A/C. This helps to dehumidify the air and to defog the windshield. In either mode, you cannot turn off the A/C.

When you switch to another mode from , the A/C stays on. Press the A/C button to turn it off.

or

To Remove Exterior Frost or Ice From the Windows

1.

. The system

Select automatically switches to fresh air mode and turns on the A/C.

Vents, Heating, and A/C

2. 3.

Select Set the fan and temperature controls to the maximum level.

To clear the windows faster, you can close the dashboard corner vents and the vents on both sides of the instrument panel by rotating the wheel below the vent. This will send more warm air to the windshield defroster vents. Once the windshield is clear, select fresh air mode to avoid fogging the windows.

For your safety, make sure you have a clear view through all the windows before driving.

To Turn Everything Off Push the fan control level down until the indicator goes off. A lack of airflow can cause the windows to fog up. You should keep the fan on at all times so stale air and moisture do not build up in the interior and cause fogging.

99

2008 S2000 ０７／０７／２５　１７：４０：４１　３１Ｓ２Ａ６８０　０１０５　

Vents and Heating

S2000 CR models

REAR WINDOW DEFOGGER BUTTON

FAN CONTROL LEVER

100

RECIRCULATION BUTTON

MODE CONTROL DIAL

TEMPERATURE CONTROL DIAL

2008 S2000 ０７／０７／２５　１７：４０：５４　３１Ｓ２Ａ６８０　０１０６　

Airflow Controls

Fan Control Lever Push this lever up and down to increase or decrease the fan speed and airflow. The indicators next to the lever show you the speed and airflow selected.

Temperature Control Dial Turning this dial clockwise increases the temperature of the airflow.

Recirculation Button When the recirculation indicator is on, air from the vehicle’s interior is sent through the system again (recirculation mode). When the indicator is off, air is brought in from the outside of the vehicle (fresh air mode).

The outside air intakes for the heating system are at the base of the windshield. Keep this area clear of leaves and other debris.

The system should be left in fresh air mode under almost all conditions. Keeping the system in recirculation mode, can cause the windows to fog up.

Switch to recirculation mode when driving through dusty or smoky conditions, then return to fresh air mode.

Vents and Heating

Rear Window Defogger Button This button turns the rear window defogger off and on (see page 61

).

Do not push the defogger button when the removable hardtop is removed.

Mode Control Dial Use the mode control dial to select the vents the air flows from. Some air will flow from the dashboard vents in all modes.

Air flows from the vents on both sides of the instrument panel, and from the dashboard vent in front of the passenger.

Airflow is divided between the vents in the dashboard and the floor vents.

CONTINUED

101

2008 S2000 ０７／０７／２５　１７：４１：０８　３１Ｓ２Ａ６８０　０１０７　

Vents and Heating

Air flows from the center

vents in the dashboard, the vents on both sides of the instrument panel, and from the floor vents. Select this position when you drive with the removable hardtop removed.

Air flows from the floor

vents and the vents on both sides of the instrument panel.

Airflow is divided between

the floor vents and the defroster vents at the base of the windshield, and the vents on both sides of the instrument panel.

Air flows from the defroster

vents at the base of the windshield and the vents on both sides of the instrument panel.

When you select the system automatically switches to Fresh Air mode.

or

102

Ventilation The flow-through ventilation system draws in outside air, circulates it through the interior, then exhausts it through vents behind the seat-backs.

1.

2. 3.

Set the temperature to the lower limit. Select Set the fan to the desired speed.

and fresh air mode.

Using the Heater The heater uses engine coolant to warm the air. If the engine is cold, it will be several minutes before you feel warm air coming from the system.

1. 2. 3.

and fresh air mode.

Select Set the fan to the desired speed. Adjust the warmth of the air with the temperature control dial.

To Defog and Defrost To remove fog from the inside of the windows:

1.

2.

3.

4.

5.

Set the fan to the desired speed, or high for faster defrosting. Select . The system automatically switches to fresh air mode. Adjust the temperature so the airflow feels warm. Select rear window. To increase airflow to the windshield, close the corner vents.

to help clear the

When you select the system automatically turns on the fresh air mode. This helps to defog the windshield.

or

2008 S2000 ０７／０７／２５　１７：４１：１４　３１Ｓ２Ａ６８０　０１０８　

To Remove Exterior Frost or Ice From the Windows

1.

2. 3.

. The system

Select automatically switches to fresh air mode. Select Set the fan and temperature controls to the maximum level.

Vents and Heating

To Turn Everything Off Push the fan control level down until the indicator goes off. A lack of airflow can cause the windows to fog up. You should keep the fan on at all times so stale air and moisture do not build up in the interior and cause fogging.

To clear the windows faster, you can close the dashboard corner vents and the vents on both sides of the instrument panel by rotating the wheel below the vent. This will send more warm air to the windshield defroster vents. Once the windshield is clear, select fresh air mode to avoid fogging the windows.

For your safety, make sure you have a clear view through all the windows before driving.

103

2008 S2000 ０７／０７／２５　１７：４１：２０　３１Ｓ２Ａ６８０　０１０９　

Playing the AM/FM Radio

U.S. models with Audio System

Canadian model

AUTO SELECT INDICATOR

AUTO SELECT INDICATOR

AM/FM BUTTON

STEREO INDICATOR

AM/FM BUTTON

STEREO INDICATOR

SEEK BAR

SCAN INDICATOR SCAN BUTTON

SCAN INDICATOR

SCAN BUTTON

PRESET BUTTONS

TUNE KNOB

PRESET BUTTONS

TUNE KNOB

PWR/VOL KNOB

AUTO SELECT BUTTON

SEEK BAR

AUTO SELECT BUTTON

PWR/VOL KNOB

104

2008 S2000 ０７／０７／２５　１７：４１：３０　３１Ｓ２Ａ６８０　０１１０　

Playing the AM/FM Radio

To Play the Radio The ignition switch must be in the ACCESSORY (I) or the ON (II) position. Turn the system on by pushing the PWR/VOL knob or the AM/FM button. Adjust the volume by turning the same knob.

The band and frequency that the radio was last tuned to is displayed. To change bands, press the AM/FM button. On the FM band, ST will be displayed if the station is broadcast- ing in stereo. Stereo reproduction in AM is not available.

To Select a Station You can use any of five methods to find radio stations on the selected band: tune, seek, scan, the preset buttons, and auto select.

−

Use the TUNE knob to

TUNE tune the radio to a desired frequency. Turn the knob right to tune to a higher frequency, or left to tune to a

lower frequency.

−

The seek function

SEEK searches up and down from the current frequency to find a station with a strong signal. To activate it, press the side of the bar, then release it.

or

−

SCAN The scan function samples all stations with strong signals on the selected band. To activate it, press the SCAN button, then release it. You will see SCAN in the display. The system will scan for a station with a strong signal. When it finds one, it will stop and play that station for about 5 seconds.

If you do nothing, the system will scan for the next strong station and play it for 5 seconds. When it plays a station you want to listen to, press the SCAN button again.

Each preset button

−

PRESET (1
and two stations on FM.

−

6) can store one station on AM,

1.

2.

3.

4.

Select the desired band, AM or FM. FM1 and FM2 let you store twelve stations.

Use the tune, seek, or scan function to tune the radio to a desired station.

Pick a preset number (1
hold it until you hear a beep.

−

6), and

Repeat steps 1 through 3 to store a total of six stations on AM and twelve stations on FM.

The preset frequencies may be lost if your vehicle’s battery goes dead, is disconnected, or the radio fuse is removed.

CONTINUED

105

2008 S2000 ０７／０７／２５　１７：４１：４１　３１Ｓ２Ａ６８０　０１１１　

Playing the AM/FM Radio

Turn the knob to adjust the setting. When the level reaches the center, you will see a ‘‘C’’ in the display. The system will return to the audio display in about 5 seconds.

Audio System Lighting You can use the instrument panel brightness control buttons to adjust the illumination of the audio system (see page ). The audio system illuminates when the parking lights are on, even if the radio is off.

60

, press the

Toturnoffautoselect A. SEL (auto select) button. This restores the presets you originally set.

Adjusting the Sound Press the SOUND/MODE (TUNE) knob repeatedly to display the bass (BAS), treble (TRE), fader (FAD), and balance (BAL) setting.

−

BAL to-side strength of the sound.

Adjusts the balance, or side-

−

FAD front-to-back strength of the sound.

Adjusts the fader, or the

TRE − sound.

BAS − sound.

Adjusts the treble in the

Adjusts the bass in the

−

If you are

AUTO SELECT traveling far from home and can no longer receive your preset stations, you can use the auto select feature to find stations in the local area.

Press the A. SEL button. ‘‘A. SEL’’ flashes in the display, and the system goes into scan mode for several seconds. It stores the frequencies of six AM and twelve FM stations in the preset buttons.

You will see a ‘‘0’’ displayed after pressing a preset button if auto select cannot find a strong station for that preset button.

If you do not like the stations auto select has stored, you can store other frequencies on the preset buttons as previously described.

106

2008 S2000 ０７／０７／２５　１７：４１：４９　３１Ｓ２Ａ６８０　０１１２　

Radio Frequencies The radio can receive the complete AM and FM bands. Those bands cover these frequen- cies:

AM band: 530 to 1,710 kHz FM band: 87.7 to 107.9 MHz

Radio stations on the AM band are assigned frequencies at least 10 kHz apart (530, 540, 550). Stations on the FM band are assigned frequencies at least 0.2 MHz apart (87.9, 88.1, 88.3).

Stations must use these exact frequencies. It is fairly common for stations to round-off the frequency in their advertising, so your radio could display a frequency of 100.9 even though the announcer may identify the station as ‘‘FM101.’’

Radio Reception How well the radio receives stations is dependent on many factors, such as the distance from the station’s transmitter, nearby large objects, and atmospheric conditions.

A radio station’s signal gets weaker as you get farther away from its transmitter. If you are listening to an AM station, you will notice the sound volume becoming weaker, and the station drifting in and out. If you are listening to an FM station, you will see the stereo indicator flickering off and on as the signal weakens. Eventually, the stereo indicator will go off and the sound will fade completely as you get out of range of the station’s signal.

AM/FM Radio Reception

Driving very near the transmitter of a station that is broadcasting on a frequency close to the frequency of the station you are listening to can also affect your radio’s reception. You may temporarily hear both stations, or hear only the station you are close to.

CONTINUED

107

2008 S2000 ０７／０７／２５　１７：４１：５５　３１Ｓ２Ａ６８０　０１１３　

AM/FM Radio Reception

AsrequiredbytheFCC: Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser’s authoritytooperatetheequipment.

Radio signals, especially on the FM band, are deflected by large objects such as buildings and hills. Your radio then receives both the direct signal from the station’s transmitter, and the deflected signal. This causes the sound to distort or flutter. This is a main cause of poor radio reception in city driving.

Radio reception can be affected by atmospheric conditions such as thunderstorms, high humidity, and even sunspots. You may be able to receive a distant radio station one day and not receive it the next day because of a change in conditions.

Electrical interference from passing vehicles and stationary sources can cause temporary reception problems.

108

2008 S2000 ０７／０７／２５　１７：４２：０１　３１Ｓ２Ａ６８０　０１１４　

OptionalonU.S.models NotavailableonCanadianmodels Your vehicle is capable of receiving XM Satellite Radio anywhere in the United States, except Hawaii and Alaska.

XM is a registered trademark of XM Satellite Radio, Inc.

Satellite radio receives signals from two satellites to produce clear, high- quality digital reception. It offers many channels in several categories. Along with a large selection of different types of music, satellite radio also allows you to view channel and category selections in the audio display.

Playing the XM Satellite Radio (Optional on U.S. Models)

AM/FM BUTTON

TUNE KNOB

CD/AUX BUTTON

SCAN BUTTON

POWER/VOLUME KNOB

PRESET BUTTONS

MORE BUTTON

CATEGORY BAR

DISPLAY/MODE BUTTON

109

2008 S2000 ０７／０７／２５　１７：４２：０９　３１Ｓ２Ａ６８０　０１１５　

Playing the XM Satellite Radio (Optional on U.S. Models)

Playing the Satellite Radio To listen to satellite radio, turn the ignition switch to the ACCESSORY (I) or ON (II) position. Push the PWR/VOL knob to turn on the audio system, and press the CD/AUX button. Adjust the volume by turning the PWR/VOL knob. The last channel you listened to will show in the display.

−

DISPLAY/MODE Each time the DISP button is pressed and released, the display information changes in the following sequence: channel name, channel number, category, artist name, and music title.

You may experience periods when XM radio does not transmit the artist name and or the song title information. If this happens, there is nothing wrong with your system. This information is not available under certain situations.

If you press and hold the DISP/ MODE button for 5 seconds, it will change between category mode and channel mode. The display will show CH for the channel mode or CATEGORY for the category mode.

In the channel mode, you can receive all of the available channels in all of the different categories. In category mode, you will receive only the stations within the selected category.

−

Expands the display to

MORE show the 6 remaining letters beyond the first 10 letters in an artist’s name or song title. The system is set up so only 16 letters can be displayed for

110

any title or name. Press MORE to view the next 6 letters. The system will return to the original display after 8 seconds.

−

TUNE Turn the TUNE knob left to go down the channels or right to go up. In the channel mode, the TUNE knob will tune up or down through all the channels available from the XM radio. In the category mode, the TUNE knob will cycle through only the channels within the category you have currently selected.

Use

CATEGORY (SEEK/SKIP) − the CATEGORY bar to select a desired category, such as jazz, rock, classical, etc. In both category mode and channel mode, pressing the category bar will change the category up or down.

2008 S2000 ０７／０７／２５　１７：４２：１８　３１Ｓ２Ａ６８０　０１１６　

Playing the XM Satellite Radio (Optional on U.S. Models)

−

The scan function gives

SCAN you a sampling of all channels while in the channel mode. In the category mode, only the channels within that category are scanned. To activate scan, press the SCAN button. The system plays each channel in numerical order for a few seconds, then selects the next channel. When you hear a channel you want to continue listening to, press the button again.

−

You can store up to 12

To store a channel: Preset preset channels using the six preset buttons. Each button stores one channel from the XM1 band and one channel from the XM2 band.

3.

Pick the preset button you want for that channel. Press and hold the button until you hear a beep.

4.

Repeat steps 2 through 3 to store the first six channels.

To store a channel: 1.

Press the CD/AUX button. Either XM1 or XM2 will show in the display.

5.

Press the CD/AUX button again. The available XM band will show. Store the next six channels using steps 2 through 3.

2.

Use the TUNE knob, the CATEGORY bar, or the SCAN buttons to tune to a desired channel.

In category mode, only channels within that category can be selected. In channel mode, all channels can be selected.

Once a channel is stored, simply press and release the proper preset button to tune to it.

The presets may be lost if your vehicle’s battery goes dead, is disconnected, or the radio fuse is removed.

CONTINUED

111

2008 S2000 ０７／０７／２５　１７：４２：２３　３１Ｓ２Ａ６８０　０１１７　

Playing the XM Satellite Radio (Optional on U.S. Models)

Signal may be blocked by mountains or large obstacles to the south.

Signal is weaker in these areas.

The XM satellites are in orbit over the equator; therefore, objects south of the vehicle may cause satellite reception interruptions. To help compensate for this, ground-based repeaters are placed in major metropolitan areas.

Satellite signals are more likely to be blocked by tall buildings and mountains the farther north you travel from the equator.

SATELLITE

112

GROUND REPEATER

2008 S2000 ０７／０７／２５　１７：４２：３２　３１Ｓ２Ａ６８０　０１１８　

Playing the XM Satellite Radio (Optional on U.S. Models)

Depending on where you drive, you may experience reception problems. Interference can be caused by any of these conditions:

Driving on the north side of an east/west mountain road.

Driving on the north side of a large commercial truck on an east/west road.

Driving in tunnels.

Driving on a road beside a vertical wall, steep cliff, or hill to the south of you.

Driving on the lower level of a multi-tiered road.

Driving on a single lane road alongside dense trees taller than 50 ft. (15 m) to the south of you.

There may also be other geographic situations that could affect satellite radio reception.

AsrequiredbytheFCC: Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser’s authoritytooperatetheequipment.

Receiving Satellite Radio Service If your XM Radio service has expired, or you purchased your vehicle from a previous owner, you can listen to a sampling of the broadcasts available on XM Satellite Radio. With the ignition switch in the ACCESSORY (I) or ON (II) position, push the PWR/VOL knob to turn on the audio system, and press the CD/AUX button. A variety of music types and styles will play.

If you decide to purchase XM satellite radio service, contact XM Radio at

www.xmradio.com

, or at

1-800-852-9696. You will need to give them your radio I.D. number and your credit card number. To get your radio I.D. number, turn the TUNE knob until ‘‘0’’ appears in the display. Your I.D. will appear in the display.

After you’ve registered with XM Radio, keep your audio system in the Satellite Radio mode while you wait for activation. This should take about 30 minutes.

While waiting for activation, make sure your vehicle remains in an open area with good reception. Once your audio system is activated, ‘‘category’’ or ‘‘CH’’ will appear in the display, and you’ll be able to listen to XM Radio broadcasts. XM Radio will continue to send an activation signal to your vehicle for at least 12 hours from the activation request. If the service has not been activated after 36 hours, contact XM Radio.

113

2008 S2000 ０７／０７／２５　１７：４２：３８　３１Ｓ２Ａ６８０　０１１９　

Playing a CD

U.S. model with Audio System

Canadian model

CD BUTTON

CD SLOT

EJECT BUTTON

CD BUTTON

CD SLOT

EJECT BUTTON

REPEAT BUTTON

REPEAT BUTTON

SEEK/SKIP BAR

RANDOM BUTTON

SEEK/SKIP BAR

RANDOM BUTTON

PWR/VOL KNOB

PWR/VOL KNOB

114

2008 S2000 ０７／０７／２５　１７：４２：４８　３１Ｓ２Ａ６８０　０１２０　

Playing a CD

To Play a CD To load or play CDs, the ignition switch must be in the ACCESSORY (I) or the ON(II) position.

You operate the CD player with the same controls used for the radio. To select the CD player, press the CD button. The number of the track playing is shown in the display. The system will continuously play a CD until you change modes.

Insert a CD about halfway into the CD slot. The drive will pull the CD in the rest of the way and begin to play it. When the system reaches the end of the disc, it will return to the beginning and play the disc again.

Do not use discs with adhesive labels. The label can curl up and cause the disc to jam in the unit.

To play the radio when a CD is playing, press the AM/FM button. Press the CD button again to switch back to the CD player.

If you turn the system off while a CD is playing, either with the PWR/VOL knob or by turning off the ignition switch, the disc will stay in the drive. When you turn the system back on, the CD will begin playing where it left off.

−

side of the skip bar,

Each time you press and

To Change or Select Tracks SKIP release the the player skips forward to the beginning of the next track. Press and release the side of the bar to skip backward to the beginning of the current track. Press it again to skip to the beginning of the previous track.

To move rapidly within a track, press and hold

or

−

To move rapidly within a

SEEK track, press and hold the SEEK/ SKIP bar. Press and hold to move forward. Press and hold

to move backward. Release the

bar when the system reaches the point you want.

CONTINUED

115

2008 S2000 ０７／０７／２５　１７：４２：５６　３１Ｓ２Ａ６８０　０１２１　

Playing a CD, CD Changer

If you turn the system off while a CD is playing, either with the PWR/VOL knob or by turning off the ignition switch, the disc will stay in the drive. When you turn the system back on, the CD will begin playing where it left off.

Operating the Optional CD Changer An optional six disc CD changer is available for your vehicle. This CD changer uses the same controls used for the in-dash CD player.

Load the desired CDs into the magazine, and load the magazine into the changer according to the instructions that came with the unit.

To select the CD changer, press the CD button. The CD and track numbers will be displayed. To select a different CD, use the preset 5
(DISC ) or preset 6 (DISC ) ＋ button. If you select an empty slot in the magazine, the changer will, after finding that slot empty, try to load the CD in the next slot.

−

−

To continuously replay

REPEAT a track, press and release the RPT button. You will see RPT in the display. Press it again to turn it off.

−

RANDOM This feature plays the tracks in random order. To activate random play, press and release the RDM button. You will see RDM in the display. Press it again to return to normal play.

) to

To Stop Playing a CD Press the eject button ( remove the CD. If you eject the CD, but do not remove it from the slot, the system will automatically reload the CD after 15 seconds and put it in pause mode. To begin playing, press the CD button. Press the AM/FM button to switch to the radio while a CD is playing.

116

2008 S2000 ０７／０７／２５　１７：４３：０６　３１Ｓ２Ａ６８０　０１２２　

General Information

When using CD-R discs, use only high quality CDs labeled for audio use.

When recording a CD-R, the recording must be closed for it to be used by the system.

CD-RW discs will not work in this unit.

Play only standard round CDs. Odd-shaped CDs may jam in the drive or cause other problems.

Handle your CDs properly to prevent damage and skipping.

Protecting CDs When a CD is not being played, store it in its case to protect it from dust and other contamination. To prevent warpage, keep CDs out of direct sunlight and extreme heat.

To clean a CD, use a clean soft cloth. Wipe across the CD from the center to the outside edge.

A new CD may be rough on the inner and outer edges. The small plastic pieces causing this roughness can flake off and fall on the re- cording surface of the CD, causing skipping or other problems. Remove these pieces by rubbing the inner and outer edges with the side of a pencil or pen.

Never try to insert foreign objects in the CD player or the magazine.

Protecting Your CDs

Handle a CD by its edges; never touch either surface. Do not place stabilizer rings or labels on the CD. These, along with contamination from fingerprints, liquids, and felt-tip pens, can cause the CD to not play properly or possibly jam in the drive.

117

2008 S2000 ０７／０７／２５　１７：４３：１６　３１Ｓ２Ａ６８０　０１２３　

Protecting Your CDs

Additional Information of Recommended CDs The CD player/changer has a sophisticated and delicate mechanism. If you insert a damaged CD as indicated in this section, it may become stuck inside and damage the audio unit.

Examples of these CDs are shown to the right:

1.

Bubbled, wrinkled, labelled, and excessively thick CDs

Bubbled/ Wrinkled

With Label/ Sticker

Using Printer Label Kit

Sealed

With Plastic Ring

2.

Damaged CDs

3.

Poor quality CDs

Chipped/ Cracked

Warped

Burrs

118

2008 S2000 ０７／０７／２５　１７：４３：２４　３１Ｓ２Ａ６８０　０１２４　

4.

Small, irregular shaped CDs