When you finish your adjustments, press the CLOCK button again.
Clock The clock displays the time with the ignition switch in the ON (II) position.
To set the clock:
1.
Turn the ignition switch to the ON (II) position.
2.
3.
Press and hold the CLOCK button until the minute display blinks. Adjust the minute by pressing the + −
button.
or
When you finish the minute adjustment, press and release the CLOCK button. The hour display will blink. Adjust the hour by pressing the button.
+ −
or
56
2008 S2000 07/07/25 17:35:26 31S2A680 0062
Controls Near the Steering Wheel
HEADLIGHTS/TURN SIGNALS (P.59)
CLOCK BUTTON (P.56)
INSTRUMENT PANEL BRIGHTNESS (P.60)
REMOTE AUDIO CONTROLS (P.122)
*
ENGINE START BUTTON (P.146)
HOOD RELEASE HANDLE (P.130)
VEHICLE STABILITY ASSIST (VSA) SYSTEM OFF SWITCH (P.153)
HEATING/COOLING CONTROLS (P.96, 100)
*
WINDSHIELD WIPERS/WASHERS (P.58)
CRUISE BUTTON (P.124)
HORN *
CRUISE CONTROL BUTTONS (P.124)
* *
1: 2 :
To use the horn, press the center pad of the steering wheel. If equipped.
57
2008 S2000 07/07/25 17:35:33 31S2A680 0063
Windshield Wipers and Washers
Push the right lever up or down to select a position.
MIST The wipers run at high speed until you release the lever.
−
OFF
−
The wipers are not activated.
−
Windshield Washers Pull the wiper control lever toward you, and hold it. The washers spray until you release the lever. The wipers run at low speed, then complete one more sweep after you release the lever.
−
The wipers operate every
INT few seconds. In low speed and high speed, the wipers run continuously.
LO
−
The wipers run at low speed.
HI
−
The wipers run at high speed.
1. 2. 3. 4. 5. 6.
MIST OFF INT LO Low speed HI High speed Windshield washers
Intermittent
− − −
58
2008 S2000 07/07/25 17:35:41 31S2A680 0064
Turn Signals and Headlights
−
Turn Signal Push down on the lever to signal a left turn and up to signal a right turn. To signal a lane change, push lightly on the lever, and hold it. The lever will return to center when you release it or complete a turn.
−
Turning the ’’ position turns
Headlights On switch to the ‘‘ on the parking lights, taillights, instrument panel lights, side-marker lights, and rear license plate lights.
Turning the switch to the ‘‘ ’’ position turns on the headlights. If you leave the lights on with the key removed from the ignition switch, you will hear a reminder buzzer when you open the driver’s door.
1. 2. 3. 4. 5. 6.
Turn Signal Off Parking and indicator lights Headlights on High beams Flash high beams
−
Push the lever
High Beams forward until you hear a click. The high beam indicator will come on (see page return to the low beams.
). Pull the lever back to
49
To flash the high beams, pull the lever back lightly, then release it. The high beams will stay on as long as you hold the lever back.
Daytime Running Lights With the headlight switch off, the high beam headlights and the high beam indicator come on with reduced brightness when you turn the ignition switch to the ON (II) position and release the parking brake. They remain on until you turn the ignition switch off, even if you set the parking brake.
The headlights revert to normal operation when you turn them on with the switch.
59
2008 S2000 07/07/25 17:35:49 31S2A680 0065
Instrument Panel Brightness, Hazard Warning Button
To reduce glare at night, the instrument panel illumination dims when you turn the light switch to the
or
position.
Adjust the brightness to the desired level with the headlight switch off, and also with the headlight switch on. Both settings will remain at those levels until you change them.
With the headlight switch on, you can switch the display to full daytime brightness by pushing and holding the button to return the display to the original brightness.
button. Push the
+
−
Hazard Warning Button
Push the red button next to the parking brake to turn on the hazard warning lights (four-way flashers). This causes all four outside turn signals and both indicators in the instrument panel to flash. Use the hazard warning lights if you need to park in a dangerous area near heavy traffic, or if your vehicle is disabled.
Instrument Panel Brightness
The buttons in the lower left corner of the instrument panel adjust the brightness of the display in five steps. Push the to see the full range.
button five times
+ −
or
60
2008 S2000 07/07/25 17:35:54 31S2A680 0066
Rear Window Defogger
Do not push the defogger button when the convertible top is folded.
Make sure the rear window is clear and you have good visibility before starting to drive.
The defogger wires on the inside of the rear window can be accidentally damaged. When cleaning the glass, always wipe side-to-side.
The rear window defogger will clear fog, frost, and thin ice from the window. Push the defogger button to turn it on and off. The indicator in the button comes on to show the defogger is on. If you do not turn it off, the defogger will shut itself off after about 15 minutes. It also shuts off when you turn off the ignition switch. You have to turn the defogger on again when you restart the vehicle.
61
2008 S2000 07/07/25 17:36:02 31S2A680 0067
The valet key works only in the ignition and the door locks. You can keep the trunk and the lower console compartment locked when you leave your vehicle and the valet key at a parking facility.
You should have received a key number tag with your keys. You will need this key number if you ever have to get a key replaced. Use only Honda-approved key blanks.
These keys contain electronic circuits that are activated by the immobilizer system. They will not work to start the engine if the circuits are damaged.
Protect the keys from direct sunlight, high temperature, and high humidity.
Do not drop the keys or set heavy objects on them.
Keep the keys away from liquids. If they get wet, dry them immediately with a soft cloth.
The keys do not contain batteries. Do not try to take them apart.
Keys and Locks
MASTER KEYS (BLACK)
VALET KEY (GREY)
KEY NUMBER TAG
The master key fits all the locks on your vehicle.
62
2008 S2000 07/07/25 17:36:10 31S2A680 0068
If the system repeatedly does not recognize the coding of your key, contact your dealer.
Do not attempt to alter this system or add other devices to it. Electrical problems could result that may make your vehicle undrivable.
If you lose your key and cannot start the engine, contact your dealer.
Always take the ignition key with you whenever you leave the vehicle alone.
The immobilizer system protects your vehicle from theft. If an improperly-coded key (or other device) is used, the engine’s fuel system is disabled.
When you turn the ignition switch to the ON (II) position, the immobilizer system indicator should come on for a few seconds, then go off. If the indicator starts to blink, it means the system does not recognize the coding of the key. Turn the ignition switch to the LOCK (0) position, remove the key, reinsert it, and turn the ignition switch to the ON (II) position again. The system may not recognize your key’s coding if another immobilizer key or other metal object (i.e. key fob) is near the ignition switch when you insert the key.
Immobilizer System
AsrequiredbytheFCC: ThisdevicecomplieswithPart15ofthe FCCrules.Operationissubjecttothe followingtwoconditions:(1)Thisdevice maynotcauseharmfulinterference,and (2)thisdevicemustacceptany interferencereceived,including interferencethatmaycauseundesired operation.
Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser’s authoritytooperatetheequipment.
ThisdevicecomplieswithIndustry CanadaStandardRSS-210. Operationissubjecttothefollowingtwo conditions:(1)thisdevicemaynotcause interference,and(2)thisdevicemust acceptanyinterferencethatmaycause undesiredoperationofthedevice.
63
2008 S2000 07/07/25 17:36:18 31S2A680 0069
Ignition Switch
−
You can
ACCESSORY (I) operate the audio system and the accessory power socket in this position.
−
This is the normal key
ON (II)
position when driving. Several of the
indicators on the instrument panel
come on as a test when you turn the
ignition switch from the
ACCESSORY (I) to the ON (II)
position.
The engine can be started with the
key in this position by pressing the
engine START button (see page
146
).
You will hear a reminder beeper if you leave the key in the ignition switch in the LOCK (0) or the ACCESSORY (I) position and open the driver’s door. Remove the key to turn off the beeper.
The ignition switch has three positions: LOCK (0), ACCESSORY (I), and ON (II).
−
You can insert or
LOCK (0) remove the key only in this position. To turn the key, push it in slightly.
If the front wheels are turned, the anti-theft lock may make it difficult to turn the key. Firmly turn the steering wheel to the left or right as you turn the key.
64
Removing the key from the ignition switch while driving locks the steering. This can cause you to lose control of the vehicle.
Remove the key from the ignition switch only when parked.
2008 S2000 07/07/25 17:36:27 31S2A680 0070
Power Door Locks
LOCK TAB
Each door has a lock tab next to the inside door handle. When you push in the lock tab on the driver’s door, both doors lock. Pulling out the lock tab on the driver’s door only unlocks that door. The lock tab on the passenger’s door only locks and unlocks that door.
To lock the passenger’s door when getting out of the vehicle, push the lock tab in and close the door. To lock the driver’s door, remove the key from the ignition switch, pull out either the inside or outside door handle and push the lock tab in, then close the door.
Both doors lock when you use the key in the driver’s door. Using the key in the passenger’s door only locks and unlocks that door. To unlock only the driver’s door from the outside, insert the key in the driver’s door lock, turn the key and release it. If you turn the key and hold it, both doors will unlock.
Power Door Locks, Trunk
Trunk
Push
TRUNK RELEASE BUTTON
To open the trunk, press the trunk release button in the lower console compartment. To protect items in the trunk when you need to give the key to someone else, lock the lower console compartment with the master key, and give the other person the valet key.
To close the trunk, press down on the trunk lid.
CONTINUED
65
2008 S2000 07/07/25 17:36:34 31S2A680 0071
Trunk
Keep the trunk lid closed at all times
while driving to avoid damaging the
lid, and to prevent exhaust gas from
Carbon
getting into the interior. See
Monoxide Hazard
41
on page
Emergency Trunk Opener
MASTER KEY
You can also use the master key to open the trunk lock.
To open the trunk with the remote transmitter, press and hold the TRUNK RELEASE button for about 1 second (see page
67
).
66
As a safety feature, your vehicle has a release lever on the trunk latch so the trunk can be opened from the inside. To open the trunk, push the release lever to the left.
Parents should decide if their children should be shown how to use this feature. For more information about child safety, see page
32
2008 S2000 07/07/25 17:36:44 31S2A680 0072
LED
UNLOCK BUTTON
LOCK BUTTON
TRUNK RELEASE BUTTON
PANIC BUTTON
−
Press this button once to
LOCK lock both doors. Some exterior lights will flash. When you push LOCK twice within 5 seconds, you will hear a beep to verify that the doors are locked.
−
Press this button once
UNLOCK to unlock the driver’s door. Push it twice to also unlock the passenger’s door.
The interior light (if the interior light
Remote Transmitter
lights will flash for about 30 seconds. To cancel panic mode, press any other button on the remote transmitter, or turn the ignition switch to the ON (II) position.
RemoteTransmitterCare
Avoid dropping or throwing the transmitter.
Protect the transmitter from extreme temperature.
Do not immerse the transmitter in any liquid.
If you lose a transmitter, the replacement needs to be reprogrammed by your dealer.
switch is in the center position) will come on when you press the UNLOCK button. If you do not open either door within 30 seconds, the light goes out. If you relock the doors with the remote transmitter before 30 seconds have elapsed, the light will go off immediately.
If you do not open either door within 30 seconds, the doors automatically relock.
You cannot lock or unlock the doors with the remote transmitter if either door is not fully closed or the key is in the ignition switch.
−
TRUNK Press this button for about 1 second to open the trunk. You cannot open the trunk if the key is in the ignition switch.
−
Press this button for
PANIC about 1 second to attract attention; the horn will sound and the exterior
67
2008 S2000 07/07/25 17:36:52 31S2A680 0073
Remote Transmitter
Replacing the Transmitter Battery
BATTERY
ROUND COVER
If it takes several pushes on the
button to lock or unlock the doors,
replace the battery as soon as
possible.
Battery type: CR2025
68
To replace the battery, remove the round cover on the back of the transmitter by turning it counterclockwise with a coin. Insert a new battery with the side facing up. Align the mark on the cover with the ◎ transmitter. Set the cover in place, and turn it clockwise.
▽ mark on the
+
AsrequiredbytheFCC: ThisdevicecomplieswithPart15ofthe FCCrules.Operationissubjecttothe followingtwoconditions:(1)Thisdevice maynotcauseharmfulinterference,and (2)thisdevicemustacceptany interferencereceived,including interferencethatmaycauseundesired operation.
An improperly disposed of battery can hurt the environment. Always confirm local regulations for battery disposal.
Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser’s authoritytooperatetheequipment.
ThisdevicecomplieswithIndustry CanadaStandardRSS-210. Operationissubjecttothefollowingtwo conditions:(1)thisdevicemaynotcause interference,and(2)thisdevicemust acceptanyinterferencethatmaycause undesiredoperationofthedevice.
2008 S2000 07/07/25 17:36:58 31S2A680 0074
Seats
−
10 12
Seepages forimportantsafety informationandwarningsabouthowto properlypositiontheseatsandseat- backs.
Make all seat adjustments before you start driving.
To adjust the seat forward and backward, pull up on the lever under the seat cushion’s front edge. Then try to move the seat to make sure it is locked in position.
To change the seat-back angle, pull up on the lever on the outside of the seat bottom.
69
2008 S2000 07/07/25 17:37:03 31S2A680 0075
Power Windows
Turn the ignition switch to the ON (II) position to raise or lower either window. To open a window, push the switch down and hold it. Release the switch when you want the window to stop. Pull back on the switch and hold it to close the window.
DRIVER’S WINDOW SWITCH
Closing a power window on someone’s hands or fingers can cause serious injury.
MAIN SWITCH
Make sure your passenger is away from the window before closing it.
PASSENGER’S WINDOW SWITCH The driver’s armrest has a master power window control panel. To open the passenger’s window, push down on the switch and hold it until the window reaches the desired position. To close the window, pull back on the window switch. Release the switch when the window gets to the position you want.
70
2008 S2000 07/07/25 17:37:08 31S2A680 0076
Power Windows
If the MAIN switch is OFF, the passenger’s window cannot be raised or lowered. Keep the MAIN switch off when you have a child in the vehicle so the child does not get injured by operating the window unintentionally.
The master control panel also con- tains these extra features:
−
AUTO To open the driver’s window fully, push the window switch firmly down to the second detent, and release it. The window automatically goes all the way down. To stop the window, pull back on the window switch briefly.
To open the driver’s window only partially, push the window switch down lightly and hold it. The window will stop as soon as you release the switch.
The AUTO function only works to lower the driver’s window. To raise the window, you must pull back on the window switch and hold it until the window reaches the desired position.
71
2008 S2000 07/07/25 17:37:18 31S2A680 0077
Lowering the Convertible Top Before operating the convertible top, make sure the vehicle is parked on level ground, the rear defogger is off, and there is enough clearance above the top.
1.
Apply the parking brake. The convertible top will not operate unless the parking brake is fully engaged.
2.
Turn the ignition switch to the ON (II) position.
LATCH
TAB
LOCKING LEVER
3.
There is a latch on each side. Push in the tabs, and pull the locking levers down.
Convertible Top
ExceptCRmodels The convertible top on your vehicle lowers and raises electrically.
It is advisable to raise the top whenever you park the vehicle. This helps to protect the vehicle from unexpected weather changes, and from theft of your valuables.
Do not operate the convertible top in f reezing weather. You can damage the material and the mechanism. Do not operate the top if it is wet, dirty, or covered with ice or snow. Never drive the vehicle with the convertible top half open. Do not operate the convertible top if the vehicle is on a jack, a hoist, or on jack stands. Park your vehicle in the shade whenever possible. Extended exposure to sunlight can cause the convertible top to deteriorate.
72
2008 S2000 07/07/25 17:37:24 31S2A680 0078
Convertible Top
Operating the convertible top while any part of a passenger is in the way of the convertible top can cause serious injury.
Make sure that you, your passenger, or any other people around the vehicle are clear of the moving convertible top.
73
LOCKING LEVER
4.
With the latches released, push the locking levers up until they latch.
5.
ROOF SWITCH Pull back and hold the ROOF switch. The windows lower and the roof folds back. Release the ROOF switch when the roof is retracted completely into the rear shelf.
Do not sit on the f olded convertible top, or place any items on top of it. You could damage the top or the rear window.
2008 S2000 07/07/25 17:37:32 31S2A680 0079
Convertible Top
Convertible Top Cover Use the convertible top cover when the top is folded to help prevent foreign objects, dirt, etc., from getting into the material and the mechanism.
The cover is attached to the body with four snaps: two behind the roll bars, and one on the side of each seat. To install or remove the convertible top cover correctly this:
, do
SNAPS
1.
Remove the convertible top cover from the trunk, and lay it into position behind the roll bar.
74
PIN
SNAP
2.
Hold the cover in place with its snap on the driver’s side of the roll bar aligned with the pin on the roll bar. Press on both sides of the snap to attach it to the pin. Do not push or pull the snap button when installing the snap.
3.
Align the snap on the passenger’s side of the roll bar with the pin. Press on both sides of the snap to attach it to the pin.
2008 S2000 07/07/25 17:37:40 31S2A680 0080
FASTENER STRAP
PIN
SNAP
4.
5.
Pull down the strap on the passenger’s side of the cover, and align its snap with the pin on the trim panel behind the door. Press on both sides of the snap to attach it to the pin.
Pull down the strap on the driver’s side of the cover, and align its snap with the pin on the trim panel behind the door. Press on both sides of the snap to attach it to the pin.
6.
Fit the rear of the cover into the space between the convertible top and its molding.
7.
To remove the cover, reverse the procedure.
Convertible Top
WindDeflector
WIND DEFLECTOR
Onallmodels The wind deflector keeps the wind out while driving with the convertible top folded or the removable hardtop removed (see page it up forward.
). To use the deflector, lift
78
75
2008 S2000 07/07/25 17:37:49 31S2A680 0081
Convertible Top
Raising the Convertible Top
1.
Apply the parking brake. The convertible top will not operate unless the parking brake is fully engaged.
2.
Turn the ignition switch to the ON (II) position.
3.
Push the ROOF switch forward and hold it. The windows, if raised, will lower automatically.
The convertible top will rise. Release the ROOF switch when the top reaches the windshield header.
4.
5.
76
TAB
LATCH
LOCKING LEVER
6.
Push the locking levers up while holding the tab. When the latch is in place, release the tab. Make sure the convertible top is securely latched.
Operating the convertible top while any part of a passenger is in the way of the convertible top can cause serious injury.
Push in the tab to release the locking levers, and pull them down. Note the movement of the latch when you push in the tab.
Make sure that you, your passenger, or any other people around the vehicle are clear of the moving convertible top.
While holding the lever down, push in the tab to engage the latch in the windshield header. Pull the top down and forward if necessary.
2008 S2000 07/07/25 17:37:56 31S2A680 0082
Do not put any heavy items on the f olded convertible top. You could damage the material and the mechanism.
Convertible Top
To reduce the possibility of leaks: Do not lean or sit on an open door.
Do not push or pull the door glass to open and close the door.
The convertible top seals are designed to promote the flow of water off the roof. Spraying high- pressure water directly on the seals can distort them, causing a leak. Use only a low-pressure water stream when using a hose, and avoid commercial car washes.
Maintenance Dust is the main cause of creaks or other sounds coming from the convertible top.
Regularly clean the body seals with glass cleaner and a soft cloth. Do not use a scraper or de-icing chemicals to remove frost, snow, or ice from the top or the rear window.
Every 3 to 6 months, depending on how often the top is folded, rub a thin film of Shin-Etsu Silicon Grease (available from your dealer, P/N 08798-9013) onto the seals wherever they touch the convertible top or each other.
77
2008 S2000 07/07/25 17:38:00 31S2A680 0083
Removable Hardtop
CRmodels Because of the size and weight of the removable hardtop, it is recommended that you have someone help you remove and install it.
Clean and dry the hardtop before removing it. Store it in your garage or other protected area, and do not stack items on top of it.
78
2008 S2000 07/07/25 17:38:08 31S2A680 0084
Removable Hardtop
LID
BOLT
BOLT
Installation 1.
Make sure the vehicle is parked on level ground, and that you have adequate clearance above the vehicle.
2.
Loosen the bolt of the rear cover lid with a flat-tipped screwdriver.
3.
Pull the bolt out until it stops against the lid.
CONTINUED
79
2008 S2000 07/07/25 17:38:16 31S2A680 0085
Removable Hardtop
BOLT
LID
LOCKING LEVER
8.
Make sure the front locking levers are closed.
9.
Make sure the handles for the side lock pins are pivoted forward to the first stop. However, do not pull the handle all the way forward (touching the inside of the top).
4.
Hold the bolt and lid, and remove the lid by pulling them up together as shown in the illustration above.
5.
Repeat the procedure for the lid on the other side.
6.
Keep the lids in the trunk safely.
7.
Move the seats forward.
80
2008 S2000 07/07/25 17:38:25 31S2A680 0086
Removable Hardtop
TAB
LATCH
LOCK ROD
REAR WINDOW DEFOGGER WIRE
10.
POSITIONING HOLE Carefully set the removable hardtop on the vehicle, making sure the lock rods go into the positioning holes behind each door. Be careful not to pinch your fingers.
Make sure that the lock rods do not damage any part of the vehicle, such as the rear wing spoiler, when you install or remove the hardtop.
11.
LOCKING LEVER Push in the tab on each locking lever and pull the locking lever down.
12.
Push the locking lever forward and set the latch into the windshield header.
13.
Pull back on the locking lever and push it up until it latches. Make sure it is securely latched.
14.
Pivot the lock rods backward to lock down the sides of the hardtop. Make sure the rear window defogger wire is set under the lock rod to ensure the wire is not crushed or entangled.
CONTINUED
81
2008 S2000 07/07/25 17:38:31 31S2A680 0087
Removable Hardtop
HARNESS
CAP
CONNECTOR
CONNECTOR
Make sure the rear window is clear and you have good visibility before starting to drive.
The defogger wires on the inside of the rear window can be accidentally damaged. When cleaning the glass, always wipe side-to-side.
16.
Plug the harness for the rear window defogger (see page into the rear connector. Make sure it locks into the connector.
61
15.
Remove the cap from the rear window defogger connector.
82
2008 S2000 07/07/25 17:38:40 31S2A680 0088
Removable Hardtop
Removal
TAB
LATCH
TAB
1.
Lower the windows.
2.
Unplug the rear window defogger harness from the connector by squeezing the tab on the harness plug. Pull on the plug, not the harness.
3.
4.
LOCKING LEVER
LOCKING LEVER
Push in the tab on each locking lever and pull the locking lever down.
5.
With the latches released, pull back on the locking levers and push them up until they latch.
Push the locking levers forward and remove the latches from the windshield header.
CONTINUED
83
2008 S2000 07/07/25 17:38:47 31S2A680 0089
Removable Hardtop
LOCK ROD
6.
Pivot the lock rods forward to release the sides of the hardtop.
7.
Lift the hardtop straight up off the vehicle and set it aside.
84
8.
Install the cap on the rear defogger connector.
9.
Take the rear cover lids out from the trunk.
Make sure that the lock rods do not damage any part of the vehicle, such as the rear wing spoiler, when you install or remove the hardtop.
2008 S2000 07/07/25 17:38:54 31S2A680 0090
Removable Hardtop
13.
Lift the wind deflector up (see page
75
).
BOLT
TABS
LID
LID
BOLT
HOLDERS
10.
When reinstalling the rear cover lid, align the tabs to the appropriate holders and push the lid down while holding the bolt out.
11.
Tighten the bolts securely with the flat-tipped screwdriver.
12.
Repeat the procedure for the lid on the other side.
85
2008 S2000 07/07/25 17:38:59 31S2A680 0091
Removable Hardtop
Storing
Washing
FRONT SEAL
Support the hardtop during storage to prevent the front seal from contacting the floor or any other surface that can deform the rubber.
Avoid automatic car washes that use a high pressure spray.
86
2008 S2000 07/07/25 17:39:07 31S2A680 0092
TAB
Adjusting the Power Mirrors
SELECTOR SWITCH
Mirrors
4.
When you finish, move the selector switch to the center (off) position. This turns the adjustment switch off to keep your settings.
Keep the inside and outside mirrors clean and adjusted for best visibility. Be sure to adjust the mirrors before you start driving.
The inside mirror has day and night positions. The night position reduces glare from headlights behind you. Flip the tab on the bottom edge of the mirror to select the day or night position.
ADJUSTMENT SWITCH
1.
Turn the ignition switch to the ON (II) position.
2.
3.
Move the selector switch to L (driver’s side) or R (passenger’s side).
Push the appropriate edge of the adjustment switch to move the mirror right, left, up, or down.
87
2008 S2000 07/07/25 17:39:12 31S2A680 0093
Parking Brake
BUTTON
Driving the vehicle with the parking brake applied can damage the rear brakes and axles. A beeper will sound if the vehicle is driven with the parking brake on.
PARKING BRAKE LEVER
To apply the parking brake, pull the lever up fully. To release it, pull up slightly, push the button, and lower the lever. The parking brake indicator on the instrument panel should go out when the parking brake is fully released (see page
46
).
88
2008 S2000 07/07/25 17:39:16 31S2A680 0094
Interior Convenience Items
CONSOLE COMPARTMENT
ACCESSORY POWER SOCKET
VANITY MIRROR/SUNVISOR
AUDIO PANEL *
DRIVER’S SEAT-BACK POCKET
BEVERAGE HOLDER
DASHBOARD LOWER POCKET
*
: If equipped
89
2008 S2000 07/07/25 17:39:24 31S2A680 0095
Interior Convenience Items
Beverage Holder
Accessory Power Socket
Open the beverage holder by pushing on the tab. The lid will slide open.
PARTITION
To hold two cups in the beverage holder, flip the partition up.
Be careful when you are using the beverage holder. A spilled liquid that is very hot can scald you or your passenger. Spilled liquids can also damage the upholstery, carpeting, and electrical components in the interior.
This socket is intended to supply
power for 12 volt DC accessories
that are rated 120 watts or less (10
amps). It will not power an
automotive type cigarette lighter
element.
90
2008 S2000 07/07/25 17:39:32 31S2A680 0096
Console Compartments
Audio Panel
UPPER COMPARTMENT
Interior Convenience Items
LOWER COMPARTMENT
The area between the seats has two compartments. Open the lower compartment by squeezing the handle. Close it with a firm push. You can lock or unlock the lower compartment with the master key.
The lever to open the upper compartment is inside the lower compartment. Push up the lever, and lift the lid. To close, lower the lid, and push it down until it latches.
Ifequipped To open the audio panel, push on the top center, and let the panel swing down. To close, pivot the panel up, and push on it until it latches.
91
2008 S2000 07/07/25 17:39:39 31S2A680 0097
Interior Convenience Items, Interior Light
Dashboard Lower Pocket
Interior Light
DOOR ACTIVATED
If the switch is in the center position, the interior light will come on when you remove the key from the ignition switch.
SWITCH
The interior light has a three- position switch; ON, Door Activated, and OFF. In the Door Activated (center) position, the light comes on when you:
Open either door. Unlock the doors with the key or the remote transmitter.
The dashboard lower pocket is located next to the audio panel.
92
2008 S2000 07/07/25 17:39:43 31S2A680 0098
When the switch is in the center position with both doors closed, the two bulbs in the interior light can each be turned on and off with the button next to it.
Interior Light
93
2008 S2000 07/07/25 17:39:45 31S2A680 0099
94
2008 S2000 07/07/25 17:39:50 31S2A680 0100
Features
. 96
...............
Vents, Heating, and A/C
. 100
........................
Vents and Heating
. 104
..........
Playing the AM/FM Radio
............
. 107
AM/FM Radio Reception
Playing the XM Satellite Radio . 109
. 114
Playing a CD
..................................
. 116
CD Changer
...................................
. 117
Protecting Your CDs
....................
.........
CD Player Error Messages
. 120
. 121
CD Changer Error Messages
.....
. 122
Remote Audio Controls
................
. 123
Radio Theft Protection
.................
...............................
Cruise Control
. 124
The heating and air conditioning system in your vehicle provides a comfortable driving environment in all weather conditions.
The standard audio system has many features. This section describes those features and how to use them. (If you have an optional audio system, refer to the operating instructions that came with it.)
Your vehicle has an anti-theft audio system that requires a code number to enable it.
95
2008 S2000 07/07/25 17:39:53 31S2A680 0101
Vents, Heating, and A/C
Except S2000 CR model
RECIRCULATION BUTTON
REAR WINDOW DEFOGGER BUTTON
AIR CONDITIONING BUTTON
FAN CONTROL LEVER
96
MODE CONTROL DIAL
TEMPERATURE CONTROL DIAL
2008 S2000 07/07/25 17:40:09 31S2A680 0102
Airflow Controls
mode).
Fan Control Lever Push this lever up and down to increase or decrease the fan speed and airflow. The indicators next to the lever show you the speed and airflow selected.
Temperature Control Dial Turning this dial clockwise increases the temperature of the airflow.
Air Conditioning (A/C) Button This button turns the air conditioning on and off. The indicator in the button comes on when the A/C is on.
Recirculation Button When the recirculation indicator is on, air from the vehicle’s interior is sent through the system again (recirculation mode). When the indicator is off, air is brought in from the outside of the vehicle (fresh air
The outside air intakes for the heating and cooling system are at the base of the windshield. Keep this area clear of leaves and other debris.
The system should be left in fresh air mode under almost all conditions. Keeping the system in recirculation mode, particularly with the A/C off, can cause the windows to fog up.
Switch to recirculation mode when driving through dusty or smoky conditions, then return to fresh air mode.
Rear Window Defogger Button
This button turns the rear window
defogger off and on (see page
61
).
Do not push the defogger button when the convertible top is folded.
Vents, Heating, and A/C
Mode Control Dial Use the mode control dial to select the vents the air flows from. Some air will flow from the dashboard vents in all modes.
Air flows from the vents on both sides of the instrument panel, and from the dashboard vent in front of the passenger.
Airflow is divided between the vents in the dashboard and the floor vents.
Air flows from the center vents in the dashboard above the audio system, the vents on both sides of the instrument panel, and from the floor vents. Select this position when you drive with the convertible top folded.
CONTINUED
97
2008 S2000 07/07/25 17:40:23 31S2A680 0103
Vents, Heating, and A/C
Air flows from the floor
vents and the vents on both sides of the instrument panel.
When you select automatically switches to fresh air mode.
, the system
Airflow is divided between
the floor vents and the defroster vents at the base of the windshield, and the vents on both sides of the instrument panel.
Air flows from the defroster
vents at the base of the windshield and the vents on both sides of the instrument panel.
When you select the system automatically switches to fresh air mode and turns on the A/C.
or
98
Ventilation The flow-through ventilation system draws in outside air, circulates it through the interior, then exhausts it through vents behind the seat-backs.
1.
2. 3. 4.
Set the temperature to the lower limit. Make sure the A/C is off. Select Set the fan to the desired speed.
and fresh air mode.
Using the Heater The heater uses engine coolant to warm the air. If the engine is cold, it will be several minutes before you feel warm air coming from the system.
1. 2. 3.
and fresh air mode.
Select Set the fan to the desired speed. Adjust the warmth of the air with