skipping or other problems. Remove these pieces by rubbing the inner and outer edges with the side of a pencil or pen.
Comfort and Convenience Features
Main MenuTable of ContentsstAudio System
CD Player Error Indications If you see an error indication in the display while operating the CD player, find the cause in the chart to the right. If you cannot clear the error indication, take the vehicle to your Honda dealer.
Comfort and Convenience Features
Main MenuTable of ContentsstCD Changer Error Indications If you see an error indication in the display while operating the CD changer, find the cause in the chart to the right. If you cannot clear the error indication, take the vehicle to your Honda dealer.
Audio System
Comfort and Convenience Features
Main MenuTable of ContentsstAudio System
Remote Audio Controls
then release it.
in the audio system display.
AUDIO CONTROL BUTTON
CHANNEL BUTTON
MUTE BUTTON
VOLUME LEVER
If you want to mute the sound temporarily, push the MUTE button. The indicator in the button will light to indicate the mute function is on. Press the button again to cancel MUTE.
The AUDIO CONTROL button changes the mode. Pressing the button repeatedly selects AM, FM1, FM2, or CD (if a CD is loaded) two.
If you are playing a CD, the system skips to the beginning of the next track each time you push the CHANNEL button.
These controls work only with the factory-installed audio system. They will not function if you install any other system.
Four controls for the audio system are on the left side of the dashboard by the instrument panel. These let you control basic fund ions without distracting your attention from driving.
Use the VOLUME lever to adjust the volume. Push the lever up to increase the volume and down to decrease it. Hold the lever until the volume reaches the desired level,
The CHANNEL button has two functions, depending on whether you are listening to the radio, or playing a CD.
If you are listening to the radio, use the CHANNEL button to change stations. Each time you press this button, the system advances to the next preset station on the band you are listening to. You will see the number of the selected Preset button
Comfort and Convenience Features
Main MenuTable of ContentsstTheft Protection Your car's audio system will disable itself if it is disconnected from electrical power for any reason. To make it work again, the user must enter a specific five-digit code in the Preset buttons. Because there are hundreds of number combinations possible from five digits, making the system work without knowing the exact code is nearly impossible.
You should have received a card that lists your audio system's code number and serial number. It is best to store this card in a safe place at home. In addition, you should write the audio system's serial number in this Owner's Manual. If you should happen to lose the card, you must obtain the code number from your Honda dealer. To do this, you will need the system's serial number.
If your car's battery is disconnected or goes dead, or the radio fuse is removed, the audio system will disable itself. If this happens, you will see "Code" in the frequency display the next time you turn on the system. Use the Preset buttons to enter the five-digit code. If it is entered correctly, the radio will start playing.
If you make a mistake entering the code, do not start over or try to correct your mistake. Complete the five-digit sequence, then enter the correct code. You have ten tries to enter the correct code. If you are unsuccessful in ten attempts, you must then leave the system on for one hour before trying again.
Audio System
You will have to store your favorite stations in the Preset buttons after the system begins working. Your original settings were lost when power was disconnected.
Comfort and Convenience Features
Main MenuTable of ContentsstBefore you begin driving your Honda, you should know what gasoline to use, and how to check the levels of important fluids. You also need to know how to properly store luggage or packages. The information in this section will help you. If you plan to add any accessories to your vehicle, please read the information in this section first.
Before Driving
Break-in Period.............................. 116
Gasoline.......................................... 116
Service Station Procedures .......... 117
Filling the Fuel Tank................. 117
Opening the Hood..................... 118
Oil Check................................ 119
Engine Coolant Check.......... 120
Fuel Economy................................ 121
Car Condition............................. 121
Driving Habits............................ 121
Accessories and Modifications.... 122
Accessories................................. 122
Modifications............................. 123
Additional Safety Precaution.... 123
Carrying Cargo.............................. 124
General Precautions...................... 127
Before Driving
Main MenustBreak-in Period, Gasoline
Break-in Period Help assure your car's future reliability and performance by paying extra attention to how you drive during the first 600 miles (1,000 km). During this period:
Avoid full-throttle starts and rapid acceleration. Do not exceed 5,500 rpm for the first 600 miles (1,000 km) of operation.
Avoid hard braking. New brakes
need to be broken-in by moderate
use for the first 200 miles (300
km).
You should follow these same re- commendations with an overhauled or exchanged engine, or when the brakes are relined.
Before Driving
In Canada, some gasolines contain an octane-enhancing additive called MMT. If you use such gasolines, your emission control system performance may deteriorate and the Malfunction Indicator Lamp on your instrument panel may turn on. If this happens, contact your authorized Honda dealer for service
Gasoline Your Honda is designed to operate on premium unleaded gasoline with a pump octane number of 91 or higher.
If you are unable to find premium unleaded gasoline, you may substi- tute an unleaded regular gasoline. The engine will compensate for the lower octane, but you may notice a slight decrease in power as a result.
We recommend gasolines containing detergent additives that help prevent fuel system and engine deposits.
Using gasoline containing lead will damage your car's emissions controls. This contributes to air pollution.
Main MenuTable of ContentsstGasoline is highly flammable and explosive. You can be burned or seriously injured when handling fuel.
Stop the engine and keep heat, sparks, and flame away. Handle fuel only outdoors. Wipe up spills immediately.
Filling the Fuel Tank
1. Because the fuel fill cap is on the driver's side of the car, park with that side closest to the service station pumps.
2. Open the fuel fill door by pulling on the knob on the driver's door jamb.
Service Station Procedures
FUEL FILL CAP
3. Remove the fuel fill cap slowly.
You may hear a hissing sound as pressure inside the tank escapes. Place the cap in the holder on the fuel fill door.
CONTINUED
Before Driving
Main MenuTable of ContentsstService Station Procedures
4. Stop filling the tank after the fuel nozzle automatically clicks off. Do not try to "lop off" the tank, leave some room for the fuel to expand with temperature changes.
5. Screw the fuel fill cap back on, tighten it until it clicks at least three times. If you do not properly tighten the cap, the Malfunction Indicator Lamp may come on (see page 228).
6. Push the fuel fill door closed until
it latches.
Before Driving
Opening the Hood
RELEASE HANDLE
1. Shift to Neutral and set the
parking brake. Pull the hood release handle located under the lower left corner of the dashboard. The hood will pop up slightly.
2. Standing in front of the car, put
your fingers under the front edge of the hood to the right of center. Slide your hand to the left until you feel the hood latch handle. Push this handle to the left until it
releases the hood. Lift the hood.
If you can open the hood without lifting the hood latch handle, or the hood latch handle moves stiffly or does not spring back as before, the mechanism should be cleaned and lubricated (see page 174).
Main MenuTable of ContentsstService Station Procedures
Oil Check
DIPSTICK
3. Pull the support rod out of its clip
and insert the end into the hole on the front of the hood around the center. To close the hood, lift it up slightly to remove the support rod from the hole. Put the support rod back into its holding clip. Lower the hood to about a foot (30 cm) above the fender, then let it drop. After closing the hood, make sure it is securely latched.
Check the engine oil level every time you fill the car with fuel. Wait a few minutes after turning the engine off before you check the oil.
1. Remove the dipstick (black
handle).
2. Wipe the dipstick with a clean
cloth or paper towel.
CONTINUED
Before Driving
Main MenuTable of ContentsstService Station Procedures
Engine Coolant Check
UPPER MARK
LOWER MARK
4. Remove the dipstick again and
check the level. It should be between the upper and lower marks.
If it is near or below the lower mark, see Adding Oil on page 157.
Look at the coolant level in the radiator reserve tank. Make sure it is between the MAX and MIN lines. If it is below the MIN line, see Adding Engine Coolant on page 161 for information on adding the proper coolant.
Refer to Owner Maintenance Checks on page 155 for information on checking other items in your Honda.
3. Insert it all the way back in its tube.
Before Driving
Main MenuTable of ContentsstThe condition of your car and your driving habits are the two most important things that affect the fuel mileage you get.
Car Condition Always maintain your car according to the maintenance schedule. This will keep it in top operating condition.
An important part of that mainte- nance is the Owner Maintenance Checks (see page 155 ). For example, an underinflated tire causes more "rolling resistance," which uses fuel. It also wears out faster, so check the tire pressure at least monthly.
In winter, the build-up of snow on your car's underside adds weight and rolling resistance. Frequent cleaning helps your fuel mileage and reduces the chance of corrosion.
Driving Habits You can improve fuel economy by driving moderately. Rapid acceler- ation, abrupt cornering, and hard braking use more fuel.
Always drive in the highest gear that allows the engine to run and acceler- ate smoothly.
Depending on traffic conditions, try to maintain a constant speed. Every time you slow down and speed up, your car uses extra fuel. Use the cruise control, when appropriate, to increase fuel economy.
A cold engine uses more fuel than a warm engine. It is not necessary to "warm-up" a cold engine by letting it idle for a long time. You can drive away in about a minute, no matter how cold it is outside. The engine will warm up faster, and you get better fuel economy. To cut down on the number of "cold starts," try to
Fuel Economy
combine several short trips into one.
The air conditioning puts an extra load on the engine which makes it use more fuel. Turn off the A/C to cut down on air conditioning use. Use the flow-through ventilation when the outside air temperature is moderate.
Before Driving
Main MenuTable of ContentsstAccessories and Modifications
Modifying your car, or installing some non-Honda accessories, can make your car unsafe. Before you make any modifications or add any accessories, be sure to read the following information.
Accessories Your dealer has Genuine Honda accessories that allow you to personalize your car. These accessories have been designed and approved for your car, and are covered by warranty.
Non-Honda accessories are usually designed for universal applications. Although aftermarket accessories may fit on your car, they may not meet factory specifications, and could adversely affect your car's handling and stability. (See "Modifications" on the page 123 for additional information.)
Before Driving
Improper accessories or modifications can affect your car's handling, stability and performance, and cause a crash in which you can be hurt or killed.
Follow all instructions in this owner's manual regarding accessories and modifications.
When properly installed, cellular phones, alarms, two-way radios, and low-powered audio systems should not interfere with your car's computer-controlled systems, such as the SRS and anti-lock brake system.
However, if electronic accessories are improperly installed, or exceed your car's electrical system capacity, they can interfere with the operation of your car, or even cause the airbags to deploy.
Before installing any accessory:
Make sure the accessory does not obscure any lights, or interfere with proper car operation or performance.
Be sure electronic accessories do not overload electrical circuits (see page 231).
Have the installer contact your Honda dealer for assistance before installing any electronic accessory.
If possible, have your dealer inspect the final installation.
Main MenuTable of ContentsstAccessories and Modifications
Modifications Do not remove any original equipment or modify your car in any way that would alter its design or operation. This could make your car unsafe and illegal to drive.
In addition, any modifications that decrease ground clearance increase the chance of undercarriage parts striking a curb, speed bump, or other raised object, which could cause your airbags to deploy.
For example, do not make any modifications that would change the ride height of your car, or install wheels and tires with a different overall diameter.
Do not modify your steering wheel or any other part of your Supplemental Restraint System. Modifications could make the system ineffective.
Additional Safety Precaution Do not attach or place objects on the airbag covers. Any object attached to or placed on the covers marked "SRS AIRBAG," in the center of the steering wheel and on top of the dashboard, could interfere with the proper operation of the airbags. Or, if the airbags inflate, the objects could be propelled inside the car and hurt someone.
Such modifications can adversely affect handling, and interfere with the operation of the car's anti-lock brakes and other systems.
Before Driving
Main MenuTable of ContentsstCarrying Cargo
UPPER AND LOWER CONSOLE COMPARTMENTS
TRUNK
Before Driving
Your car has several convenient storage areas so yon can stow cargo safely.
The upper and lower console compartments are designed for small, lightweight items. The trunk is intended for larger, heavier items.
However, carrying too much cargo, or improperly storing it, can affect your car's handling, stability and operation and make it unsafe. Before carrying any type of cargo, be sure to read the following pages.
Main MenuTable of ContentsstOverloading or improper loading can affect handling and stability and cause a crash in which you can be hurt or killed.
Follow all load limits and other loading guidelines in this manual.
Carrying Cargo
Carrying Items in the Passenger Compartment
Store or secure all items that could be thrown around and hurt someone during a crash.
Be sure items placed on the floor behind the front scats cannot roll under the seats and interfere with the driver's ability to operate the pedals, or with the proper operation of the seats.
Load Limit The maximum load for your car is 400 Ibs (185 kg).
This figure includes the total weight of all occupants, cargo, and accessories.
To figure out how much cargo you can carry:
Add up the weight of all occupants.
Subtract the total from 400 Ib (185
kg).
The final number is the total weight of cargo you can cany.
Before Driving
Main MenuTable of ContentsstCarrying Cargo
Carrying Cargo in the Trunk
Distribute cargo evenly on the floor of the trunk, placing the heaviest items on the bottom and as far forward as possible.
Before Driving
Main MenuTable of ContentsstYour Honda is designed to give you optimum handling and performance on well-maintained roads. As part of this design, your car has a minimum of ground clearance and very low- profile tires.
Use caution if you should drive your car on very rough or rutted roads. You could damage the suspension and underbody by bottoming out. Going too fast over parking lot "speed bumps" can also cause damage.
Curbs and steep inclines could damage the front and rear bumpers. Low curbs that do not affect the average car may be high enough to hit the bumper on your Honda. The front or rear bumper may scrape when trying to drive onto an incline, such as a steep driveway or trailer ramps.
General Precautions
Because of the low-profile tires fitted to your car, the alloy wheels are closer to the ground. Driving over a pothole or road debris at too high a speed can seriously damage a wheel. Slow down under these conditions.
Before Driving
Main MenuTable of ContentsstThis section gives you tips on starting the engine under various conditions, and how to operate the manual transmission. It also includes important information on parking your car, and the braking system.
Driving
Preparing to Drive......................... 130
Starting the Engine........................ 131
Starting in Cold Weather
at High Altitude..................... 132
6-speed Manual Transmission..... 133
Recommended Shift Points...... 134
Engine Speed Limiter............... 134
Reverse Lockout........................ 134
Parking............................................ 135
The Braking System...................... 136
Brake Wear Indicators.............. 136
Brake System Design................ 137
Anti-lock Brakes........................ 137
Important Safety
Reminders.......................... 138
ABS Indicator......................... 139
Driving in Bad Weather................ 140
Towing a Trailer............................ 141
Driving
Main MenustPreparing to Drive
You should do the following checks and adjustments every day before you drive your car.
1. Make sure all windows, mirrors, and outside lights are clean and unobstructed. Remove frost, snow, or ice.
2. Check that the hood and trunk are
fully closed.
3. Visually check the tires. If a tire
looks low, use a gauge to check its pressure.
4. Check that any items you may be
carrying with you inside are stored properly or fastened down securely.
5. Check the adjustment of the seat
(see page 68).
6. Check the adjustment of the
inside and outside mirrors (see page 79).
7. Make sure the doors are securely
closed and locked.
8. Fasten your seat belt. Check that your passenger has fastened his seat belt (see page 15).
9. Turn the ignition switch ON (II). Check the indicator lights in the instrument panel.
10. Start the engine (see page 131).
11. Check the gauges and indicator
lights in the instrument panel (see page 4 3).
Driving
Main MenuTable of Contentsst1. Apply the parking brake.
2. In cold weather, turn off all
electrical accessories to reduce the drain on the battery.
3. Push the clutch pedal down all the way. The ENGINE START button has no effect unless the clutch pedal is depressed.
4. Turn the ignition key to ON (II)
position.
ENGINE START BUTTON
5. Without touching the accelerator pedal, push the ENGINE START button. If the engine does not start right away, do not hold the ENGINE START button for more than 15 seconds at a time. Pause for at least 10 seconds before trying again.
Starting the Engine
6. If the engine does not start within
15 seconds, or starts but stalls right away, repeat step 5 with the accelerator pedal pressed half-way down. If the engine starts, release pressure on the accelerator pedal so the engine does not race.
7. If the engine still does not start,
press the accelerator pedal all the way down and hold it there while starting in order to clear flooding. As before, hold the ENGINE START button for no more than 15 seconds. Return to step 6 if the engine does not start. If it starts, lift your foot off the accelerator pedal so the engine does not race.
Driving
Main MenuTable of ContentsstStarting the Engine
Starting in Cold Weather at High
Altitude (Above 8,000 feet/
2,400 meters)
An engine is harder to start in cold
weather. The thinner air found at
high altitude above 8,000 feet (2,400
meters) adds to the problem.
Use the following procedure:
1. Turn off all electrical accessories
to reduce the drain on the battery.
2. Push the accelerator pedal half- way to the floor and hold it there while starting the engine. Do not hold the ENGINE START button for more than 15 seconds. When the engine starts, release the accelerator pedal gradually as the engine speeds up and smooths out.
3. If the engine fails to start in step 2,
push the accelerator pedal to the floor and hold it there while you try to start the engine for no more than 15 seconds. If the engine does not start, return to step 2.
Driving
Main MenuTable of Contentsst6-speed Manual Transmission
Rapid slowing or speeding-up can cause loss of control on slippery surfaces. If you crash, you can be injured.
Use extra care when driving on slippery surfaces.
Come to a full stop before you shift into Reverse. You can damage the transmission by trying to shift into Reverse with the car moving. Push down the clutch pedal, and pause for a few seconds before shifting into Reverse, or shift into one of the forward gears for a moment. This stops the gears so they won't "grind."
When slowing down, you can get extra braking from the engine by shifting to a lower gear. This extra braking can help you maintain a safe speed and prevent your brakes from overheating while going down a steep hill. Before downshifting, make sure engine speed will not go into the tachometer's red zone in the lower gear.
Driving
The manual transmission is synchro- nized in all forward gears for smooth operation. It has a lockout so you cannot shift directly from Fifth to Reverse instead of sixth (see page 134). When shifting up or down, make sure you push the clutch pedal down all the way, shift to the next gear, and let the pedal up gradually. When you are not shifting, do not rest your foot on the clutch pedal. This can cause your clutch to wear out faster.
Main MenuTable of Contentsst6-speed Manual Transmission
Recommended Shift Points Drive in the highest gear that lets the engine run and accelerate smoothly. This will give you the best fuel economy and effective emis- sions control. The following shift points are recommended:
Engine Speed Limiter If you exceed the maximum speed for the gear you are in, the engine speed will enter into the tachometer's red zone. If this occurs, you may feel the engine cut in and out. This is caused by a limiter in the engine's computer controls. The engine will run normally when you reduce the RPM below the red zone.
Before downshifting, make sure the engine will not go into the tachometer's red zone in the lower gear.
Reverse Lockout
The 6-speed manual transmission has a lockout so you cannot accidentally shift from Fifth to Reverse instead of Sixth.
With the clutch pedal depressed, move the shift lever to the Reverse side of the Neutral gate, then push the shift lever down and shift to Reverse.
Driving
Main MenuTable of ContentsstAlways use the parking brake when you park your car. The indicator on the instrument panel shows that the parking brake is not fully released; it does not indicate that the parking brake is firmly set. Make sure the parking brake is set firmly or your car may roll if it is parked on an incline.
If the car is facing uphill, turn the front wheels away from the curb and put the transmission in first gear. If the car is facing downhill, turn the front wheels toward the curb and put the transmission in reverse gear.
Make sure the parking brake is fully released before driving away. Driving with the parking brake partially set can overheat or damage the rear brakes.
Parking
Parking Tips
Make sure the convertible top and the windows are closed.
Turn off the lights.
Place any packages, valuables, etc., in the trunk or take them with you.
Lock the doors with the key or the remote transmitter.
Never park over dry leaves, tall grass, or other flammable materials. The three way catalytic converter gets very hot, and could cause these materials to catch on fire.
Driving
Main MenuTable of ContentsstThe Braking System
Your Honda is equipped with disc- brakes at all four wheels. A power assist helps reduce the effort needed on the brake pedal. The ABS helps you retain steering control when braking very hard.
Put your foot on the brake pedal only when you intend to brake. Resting your foot on the pedal keeps the brakes applied lightly, causing them to build up heat. Heat build-up can reduce how well your brakes work. It also keeps your brake lights on all the time, confusing drivers behind you.
Constant application of the brakes when going down a long hill builds up heat and reduces their effective- ness. Use the engine to assist the brakes by downshifting to a lower gear and taking your foot off the accelerator pedal.
Check your brakes after driving through deep water. Apply the brakes moderately to see if they feel normal. If not, apply them gently and frequently until they do. Since a longer distance is needed to stop with wet brakes, be extra cautious and alert in your driving.
Brake Wear Indicators All four brakes have audible brake wear indicators. When the brake pads need replacing, you will hear a distinctive metallic "screeching" sound when you apply the brakes. If you do not have the brake pads replaced, they will begin screeching all the time.
Your brakes may sometimes squeal or squeak when you apply them lightly. Do not confuse this with the brake wear indicators. They make a very audible "screeching."
Driving
Main MenuTable of ContentsstThe Braking System
Brake System Design The hydraulic system that operates the brakes has two separate circuits. Each circuit works diagonally across the car (the left-front brake is connected with the right-rear brake, etc.). If one circuit should develop a problem, you will still have braking at two wheels.
Anti-lock Brakes Your car has an Anti-lock Brake System (ABS) as standard equipment. ABS helps to prevent the wheels from locking up and skidding during hard braking, allowing you to retain steering control.
When the front tires skid, you lose steering control; the car continues straight ahead even though you turn the steering wheel. The ABS helps to prevent lock-up and helps you retain steering control by pumping the brakes rapidly; much faster than a person can do it.
Front
CONTINUED
Driving
Main MenuTable of ContentsstThe Braking System
You should never pump the brake pedal, this defeats the purpose of the ABS. Let the ABS work for you by always keeping firm, steady pressure on the brake pedal as you steer away from the hazard. This is sometimes referred to as "stomp find steer."
You will feel a pulsation in the brake pedal when the ABS activates, and you may hear some noise. This is normal, it is the ABS rapidly pumping the brakes.
Activation varies with the amount of traction your tires have. On dry pavement, you will need to press on the brake pedal very hard before you activate the ABS. However, you may feel the ABS activate immediately if you are trying to stop on snow or ice.
Driving
Important Safety Reminders ABS does not reduce the time or distance it takes to stop the car, it only helps with steering control during braking. You should always maintain a safe following distance from other vehicles.
A car with ABS may require a longer distance to stop on loose or uneven surfaces, such as gravel or snow, than a car without anti-lock. Slow down and allow a greater distance between cars under those conditions.
ABS will not prevent a skid that results from changing direction abruptly, such as trying to take a corner too fast or making a sudden lane change. Always drive at a safe, prudent speed for the road and weather conditions.
ABS cannot prevent a loss of stability. Always steer moderately when you are braking hard. Severe or sharp steering wheel movement can still cause your car to veer into oncoming traffic or off the road.
Main MenuTable of ContentsstABS Indicator
ANTI-LOCK BRAKE SYSTEM INDICATOR
U.S. indicator shown
The ABS is self-checking. If anything goes wrong, the ABS indicator on the instrument panel comes on (see page 45). This means the anti-lock function of the braking system has shut down. The brakes still work like a conventional system without anti- lock, providing normal stopping ability. You should have the dealer inspect your car as soon as possible.
The Braking System
Driving
Main MenuTable of ContentsstDriving in Bad Weather
Rain, fog, and snow conditions re- quire a different driving technique because of reduced traction and visibility. Keep your car well- maintained and exercise greater caution when you need to drive in bad weather. The cruise control should not be used in these condi- tions.
Driving
Visibility — Being able to see clearly in all directions and being visible to other drivers are important in all weather conditions. This is more difficult in bad weather. To be seen more clearly during daylight hours, turn on your headlights.
Inspect your windshield wipers and washers frequently. Keep the wind- shield washer reservoir full of the proper fluid. Have the windshield wiper blades replaced if they start to streak the windshield or leave parts unwiped. Use the defrosters and air conditioning to keep the windows from fogging up on the inside (see page 91).
Driving Technique — Always drive slower than you would in dry weather. It takes your car longer to react, even in conditions that may seem just barely clamp. Apply smooth, even pressure to all the controls. Abrupt steering wheel movements or sudden, hard appli- cation of the brakes can cause loss of control in wet weather. Be extra cautious for the first few miles (kilometers) of driving while you adjust to the change in driving conditions. This is especially true in snow. A person can forget some snow-driving techniques during the summer months. Practice is needed to relearn those skills.
Exercise extra caution when driving in rain after a long dry spell. After months of dry weather, the first rains bring oil to the surface of the roadway, making it slippery.
Main MenuTable of ContentsstTraction — Check your tires frequently for wear and proper pressure. Both are important in preventing "hydroplaning" (loss of traction on a wet surface). In the winter, mount snow tires on all four wheels for the best handling.
Watch road conditions carefully, they can change from moment to moment. Wet leaves can be as slip- pery as ice. "Clear" roads can have patches of ice. Driving conditions can be very hazardous when the outside temperature is near freezing. The road surface can become covered with areas of water puddles mixed with areas of ice, so your traction can change without warning.
Be careful when downshifting. If traction is low, you can lock up the drive wheels for a moment and cause a skid.
Driving in Bad Weather, Towing a Trailer
Towing a Trailer Your car is not designed to tow a trailer. Attempting to do so can void your warranties.
Be very cautious when passing, or being passed by other cars. The spray from large cars reduces your visibility, and the wind buffeting can cause you to lose control.
Driving
Main MenuTable of ContentsstThis section explains why it is important to keep your car well maintained and to follow basic maintenance safety precautions.
This section also includes Maintenance Schedules for normal driving and severe driving conditions, a Maintenance Record, and instruc- tions for simple maintenance tasks you may want to take care of yourself.
If you have the skills and tools to per- form more complex maintenance tasks on your Honda, you may want to purchase the Service Manual. See page 259 for information on how to obtain a copy, or see your Honda dealer.
Maintenance Safety....................... 144
Important Safety Precautions.. 145
Maintenance Schedule.................. 146
Required Maintenance Record.... 153
Owner Maintenance Checks........ 155
Fluid Locations............................... 156
Engine Oil....................................... 157
Adding Oil................................... 157
Recommended Oil..................... 157
Synthetic Oil............................... 158
Additives..................................... 158
Changing the Oil and Filter...... 159
Cooling System.............................. 161
Adding Engine Coolant............. 161
Replacing Engine Coolant........ 163
Windshield Washers..................... 167
6-speed Manual Transmission
Fluid............................................ 168
Differential Fluid........................... 169
Brake and Clutch Fluid................. 170
Brake Fluid................................. 170
Brake System............................. 170
Clutch System............................ 171
Air Cleaner Element...................... 172
Hood Latch..................................... 174
Maintenance
Spark Plugs..................................... 174
Replacement............................... 174
Specifications............................. 176
Battery............................................ 177
Wiper Blades.................................. 180
Air Conditioning System............... 182
Air Conditioning Filter.................. 183
Drive Belt........................................ 184
Tires................................................ 185
Inflation....................................... 185
Inspection................................... 187
Maintenance............................... 188
Tire Rotation.............................. 188
Tire Wear.................................... 188
Replacing Tires and Wheels .... 189
Wheels and Tires....................... 190
Winter Driving........................... 190
Snow Tires.............................. 191
Tire Chains............................. 191
Lights.............................................. 192
Replacing Bulbs......................... 194
Storing Your Car............................ 202
Maintenance
Main MenustMaintenance Safety
Regularly maintaining your car is the best way to protect your investment. Proper maintenance is essential to your safety and the safety of your passengers. It will also reward you with more economical, trouble-free driving and help reduce air pollution.
This section includes instructions for simple maintenance tasks, such as checking and adding oil. Any service items not detailed in this section should be performed by a Honda technician or other qualified mechanic.
Some of the most important safety precautions are given here. However, we cannot warn you of every conceivable hazard that can arise in performing maintenance. Only you can decide whether or not you should perform a given task.
Improperly maintaining this car or failing to correct a problem before driving can cause a crash in which you can be seriously hurt or killed.
Always follow the inspection and maintenance recommendations and schedules in this owner's manual.
Maintenance
Failure to properly follow maintenance instructions and precautions can cause you to be seriously hurt or killed.
Always follow the procedures and precautions in this owner's manual.
Main MenuTable of ContentsstImportant Safety Precautions Before you begin any maintenance, make sure your car is parked on level ground and that the parking brake is set. Also, be sure the engine is off. This will help to eliminate several potential hazards:
Carbon monoxide poisoning from engine exhaust. Be sure there is adequate ventilation whenever you operate the engine.
Burns from hot parts. Let the engine and exhaust system cool before touching any parts.
Injury from moving parts. Do not run the engine unless in- structed to do so.
Read the instructions before you begin, and make sure you have the tools and skills required.
To reduce the possibility of fire or explosion, be careful when working around gasoline or batteries. Use a commercially available degreaser or parts cleaner, not gasoline, to clean parts. Keep cigarettes, sparks, and flames away from the battery and all fuel-related parts.
You should wear eye protection and protective clothing when working near the battery or when using compressed air.
Maintenance Safety
Maintenance
Main MenuTable of ContentsstWhich Schedule to Follow: Service your car according to the time and mileage periods on one of the Maintenance Schedules on the following pages. Select the schedule for "Severe Conditions" if most of your driving is done under one or more of the conditions listed on that page. Otherwise, follow the schedule for "Normal Conditions."
Maintenance Schedule
The Maintenance Schedule specifies how often you should have your car serviced and what things need attention. It is essential that you have your car serviced as scheduled to retain its high level of safety, dependability, and emissions control performance.
The services and time or distance intervals shown in the maintenance schedule assume you will use your car as normal transportation for your passenger and possessions. You should also follow these recommendations:
Avoid exceeding your car's load limit. This puts excess stress on the engine, brakes, and many other parts of your car. The load limit is shown on the label on the driver's doorjamb.
Operate your car on reasonable roads within the legal speed limit.
Drive your car regularly over a distance of several miles (kilometers).
Always use unleaded gasoline with the proper octane rating (see page 116).
Maintenance
Main MenuTable of ContentsstYour authorized Honda dealer knows your car best and can provide competent, efficient service. However, service at a dealer is not mandatory to keep your warranties in effect. Maintenance may be done by any qualified service facility or person who is skilled in this type of automotive service. Keep all the receipts as proof of completion, and have the person who does the work fill out the Maintenance Record. Check your warranty booklet for more information.
We recommend the use of Genuine Honda parts and fluids whenever you have maintenance done. These are manufactured to the same high- quality standards as the original components, so you can be confident of their performance and durability.
U.S. Cars: Maintenance, replacement or repair of emissions control devices and systems may be done by any automotive repair establishment or individual using parts that are "certified" to EPA standards.
Maintenance Schedule
According to state and federal regulations, failure to perform maintenance on the items marked with # will not void your emissions warranties. However, Honda recommends that all maintenance services be performed at the recommended time or mileage period to ensure long-term reliability.
Maintenance
Main MenuTable of ContentsstU.S. Owners Follow the Normal Conditions Maintenance Schedule if the severe driving conditions specified in the Severe Conditions Maintenance Schedule do not apply.
NOTE: If yon only OCCASIONALLY drive under a "severe" condition, you should follow the Normal Conditions Maintenance Schedule.
Canadian Owners Follow the Maintenance Schedule for Severe Conditions.
#: See information on maintenance and
emissions warranty, last column, page 147 .
Maintenance
Main MenuTable of ContentsstService at the indicated distance or time, whichever comes first. Do the items in A, B, C as required for each distance/time interval. Follow this schedule if the severe driving conditions described in the Severe Conditions Schedule on the next page do not apply. Canadian owners: Follow the schedule for Severe Conditions.
Note:
Check engine oil and coolant at each fuel stop. Check and adjust valve clearance, cold engine, if noisy.
# : See information on maintenance and emissions warranty, last
column, page 147.
Maintenance
Main MenuTable of ContentsstU.S. Owners Follow the Severe Conditions Maintenance Schedule if you drive your vehicle MAINLY under one or more of the following conditions:
Driving less than 5 miles (8
km) per trip or, in freezing
temperatures, driving less
than 10 miles (16 km) per trip.
Driving in extremely hot
[over 90°F (32°C)] conditions.
Extensive idling or long
periods of stop-and-go driving.
Driving in mountainous
conditions.
Driving on muddy, dusty, or
de-iced roads.
Canadian Owners Follow the Maintenance Schedule for Severe Conditions.
#: See information on maintenance and
emissions warranty, last column, page 147 .
* 1 : Refer to page 183 for replacement information under special driving conditions.
Maintenance
Main MenuTable of ContentsstUse this schedule if your vehicle is MAINLY driven in any of the following Severe Conditions, or normally driven in Canada; otherwise use the Normal Schedule. Service at the indicated distance or time, whichever comes first. Do the items in A, B, C, D as required for each distance/time.
Note:
Check engine oil and coolant at each fuel stop. Check and adjust valve clearance, cold engine, if noisy.
CONTINUED
Maintenance
Main MenuTable of Contentsstpage 147
Maintenance
Main MenuTable of ContentsstRequired Maintenance Record (for Normal and Severe Schedules)
You or the servicing dealer can record all completed maintenance here, whether you follow the schedule for normal conditions (page 148 ) or severe conditions (page 150 ). Keep the receipts for all work done on your vehicle.
CONTINUED
Maintenance
Main MenuTable of ContentsstRequired Maintenance Record (for Normal and Severe Schedules)
Maintenance
Main MenuTable of ContentsstYou should check the following items at the specified intervals. If you are unsure of how to perform any check, turn to the page given.
Owner Maintenance Checks
Tires — Check the tire pressure monthly. Examine the tread for wear and foreign objects. See page 186.
Lights — Check the operation of the headlights, parking lights, taillights, high-mount brake light, turn signals, brake lights, and license plate lights monthly. See page 192.
Engine oil level — Check every time you fill the fuel tank. See page 119.
Engine coolant level - Check the radiator reserve tank every time you fill the fuel tank. See page 120.
Windshield washer fluid — Check the level in the reservoir monthly. If weather conditions cause you to use the washers frequently, check the reservoir each time you stop for fuel. See page 167.
Brakes and clutch — Check the fluid level monthly. See page 170 .
Maintenance
Main MenuTable of ContentsstENGINE OIL FILL CAP
CLUTCH FLUID (Gray cap)
BRAKE FLUID (Gray cap)
COOLANT RESERVOIR
Fluid Locations
WASHER FLUID (Blue cap)
ENGINE OIL DIPSTICK
Maintenance
Main MenuTable of ContentsstAdding Oil
To add oil, unscrew and remove the engine oil fill cap on lop of the left valve cover. Pour in the oil, and replace the engine oil fill cap. Tighten it securely. Wait a few minutes and recheck the oil level. Do not fill ahove the upper mark; you could damage the engine.
Recommended Oil Oil is a major contributor to your engine's performance and longevity. Always use a premium-grade deter- gent oil. It is highly recommended that you use Genuine Honda Motor oil in your vehicle for as long as you own it.
You can determine an oil's SAE viscosity and Service Classification from the API Service label on the oil container.
A fuel-efficient oil is recommended for your Honda. This is shown on the API Service label by the words "Energy Conserving." This oil is formulated to help your engine use less fuel.
Engine Oil
The API Service label also tells you the service classification of the oil. Always use an oil that is labeled "API Service SJ." This service rating may include other classifications, such as CD. These additional classifications are not a problem, as long as the label also carries the SJ classification.
API SERVICE LABEL
CONTINUED
Maintenance
Main MenuTable of ContentsstEngine Oil
The oil container may also display the API Certification seal. Make sure it says "For Gasoline Engines."
The SAE numbers tell you the oil's viscosity or weight. Select the oil for your car according to this chart.
API CERTIFICATION SEAL
Ambient Temperature
An oil with a viscosity of 10W-30 is preferred for improved fuel economy and year-round protection in your Honda. You may use a 5W-40 oil if the temperature in your area goes below 0°F(—20°C).
Maintenance
Synthetic Oil You may use a synthetic motor oil if it meets the same requirements given for conventional motor oil: energy conserving, a service classification of SJ, and the proper weight as shown on the chart. When using synthetic oil, you must follow the oil and filter change intervals given in the maintenance schedule.
Additives Your Honda does not need any oil additives. Purchasing additives for the engine or transmission will not increase your car's performance or longevity. It only increases the cost of operating your car.
Main MenuTable of ContentsstChanging the Oil and Filter Always change the oil and filter according to the time and distance (miles/kilometers) recommenda- tions in the maintenance schedule. The oil and filter collect contami- nants that can damage your engine if they are not removed regularly.
Changing the oil and filter requires special tools and access from underneath the car. The car should be raised on a service station-type hydraulic lift for this service. Unless you have the knowledge and proper equipment, you should have this maintenance done by a skilled mechanic.
1. Run the engine until it reaches normal operating temperature, then shut it off.
Engine Oil
WASHER
OIL DRAIN BOLT
2. Remove the engine oil fill cap.
Remove the oil drain bolt from the bottom of the engine. Drain the oil into an appropriate container.
OIL FILTER
3. Remove the oil filter and let the
remaining oil drain. A special wrench (available from your Honda dealer) is required to remove the filter.
4. Install a new oil filter according to
instructions that come with it.
CONTINUED
Maintenance
Main MenuTable of ContentsstNOTICE
Improper disposal of engine oil can be harmful to the environment. If yon change your own oil, please dispose of the used oil properly. Put it in a sealed container and take it to a recycling center. Do not discard it in a trash bin or dump it on the ground.
Engine Oil
5. Put a new washer on the drain bolt,
then reinstall the drain bolt. Tighten it to: 33 lbf.ft (45 N.m,4.6 kgf.m)
9. Turn off the engine, let it sit for
several minutes, then check the oil level. If necessary, add oil to bring the level to the upper mark on the dipstick.
6. Refill the engine with the recom-
mended oil. Engine oil change capacity (including filter): 5.1 US qt (4.8
,4.2 Imp qt)
7. Install the engine oil fill cap. Start
the engine. The oil pressure indicator light should go out within five seconds. If it does not, turn off the engine and reinspect your work.
8. Let the engine run for several
minutes and check the drain bolt and oil filter for leaks.
Maintenance
Main MenuTable of ContentsstCooling System
Always use Genuine Honda Antifreeze/Coolant. If it is not available, you may use another major-brand non-silicate coolant as a temporary replacement. Make sure it is a high-quality coolant recommended for aluminum engines. However, continued use of any non- Honda coolant can result in corrosion, causing the cooling system to malfunction or fail. Have the cooling system flushed and refilled with Honda antifreeze/ coolant as soon as possible.
If the reserve tank is completely empty, you should also check the coolant level in the radiator.
Removing the radiator cap while the engine is hot can cause the coolant to spray out, seriously scalding you.
Always let the engine and radiator cool down before removing the radiator cap.
1. Make sure the engine and radiator
are cool.
Adding Engine Coolant
RESERVE TANK
MAX
MIN
If the coolant level in the reserve tank is at or below the MIN line, add coolant to bring it up to the MAX line. Inspect the cooling system for leaks. This coolant should always be a mixture of 50 percent antifreeze and 50 percent water. Never add straight antifreeze or plain water.
CONTINUED
Maintenance
Main MenuTable of ContentsstCooling System
RADIATOR CAP
RESERVE TANK
Do not add any rust inhibitors or other additives to your vehicle's cooling system. They may not be compatible with the coolant or engine components.
2. Turn the radiator cap counter-
clockwise, without pressing down on it, until it stops. This relieves any pressure remaining in the cooling system.
3. Remove the radiator cap by
pushing down and turning counterclockwise.
4. The coolant level should be up to
the base of the filler neck. Add coolant if it is low.
5. Put the radiator cap back on.
Tighten it fully.
6. Pour coolant into the reserve tank. Fill it to halfway between the MAX and MIN marks. Put the cap back on the reserve tank.
Maintenance
Main MenuTable of ContentsstReplacing Engine Coolant The cooling system should be completely drained and refilled with new coolant according to the time and distance recommendations in the maintenance schedule. Only use Genuine Honda Antifreeze/Coolant.
Draining the coolant requires access to the underside of the vehicle. Unless you have the tools and knowledge, you should have this maintenance done by a skilled mechanic.
Cooling System
DRAIN BOLT
DRAIN PLUG
4. Loosen the drain plug on the bottom of the radiator. The coolant will drain through the splash guard. Remove the drain bolt and washer from the engine block.
1. Turn the ignition ON (II). Turn the heater temperature control dial fully clockwise. Turn the ignition off.
2. Open the hood. Make sure the
engine and radiator are cool to the touch.
3. Remove the radiator cap.
CONTINUED
Maintenance
Main MenuTable of ContentsstCooling System
RESERVE TANK CAP
HOLDER
RESERVE TANK
5. Remove the reserve tank from its
holder by pulling it straight up. Drain the coolant, then put the tank back in its holder.
6. When the coolant stops draining,
tighten the drain plug at the bottom of the radiator. Apply non-hardening sealant to the drain bolt threads, put a new washer on the drain bolt, and reinstall the bolt in the engine block. Tighten it securely. Tightening torque: 61 lbf.ft(83 N.m , 8.5 kgf.m)
7. Mix the recommended antifreeze with an equal amount of purified or distilled water in a clean container. The cooling system capacity is: 1.72 US gal (6.5
, 1.43 Imp gal)
BLEEDER BOLT
8. Loosen the bleeder bolt on top of
the engine, and remove the bleeder cap near the engine oil fill cap. Pour coolant into the radiator up to the base of the filler neck. Tighten the bleeder bolt and reinstall the bleeder cap when coolant comes out in a steady stream with no bubbles.
Maintenance
Main MenuTable of ContentsstBLEEDER CAP
Fill up to here
RESERVE TANK
Cooling System
FILLER NECK
9. Start the engine and let it run for about 30 seconds. Then turn off the engine.
10. Pour coolant into the radiator up
to the base of the filler neck.
11. Fill the reserve tank to the MAX
mark. Install the reserve tank cap.
12. Install the radiator cap, and
tighten it to the first stop.
13. Start the engine and let it run until
the radiator fan comes on two times. Then stop the engine.
CONTINUED
Maintenance
Main MenuTable of ContentsstCooling System
14. Remove the radiator cap.
15. Pour coolant into the radiator up to the base of the filler neck and into the reserve tank up to the MAX mark.
16. Start the engine and hold it at
1,500 rpm until the radiator fan comes on. Turn off the engine. Check the coolant level in the radiator and add coolant if needed.
17. Install the radiator cap, and
tighten it fully.
18. If necessary, fill the reserve tank
to the MAX mark. Install the reserve tank cap.
Maintenance
Main MenuTable of ContentsstRESERVOIR CAP
Check the reservoir's fluid level by removing the cap and looking at the level gauge attached to the cap.
Check the level in the windshield washer reservoir at least monthly during normal usage. In bad weather, when you use the washers often, check the level every time you stop for fuel.
The windshield washer reservoir is located in the rear of the engine compartment on the passenger's side.
Windshield Washers
Fill the reservoir with a good-quality windshield washer fluid. This increases the cleaning capability and prevents freezing in cold weather.
When you refill the reservoir, clean the edges of the windshield wiper blades with windshield washer fluid on a clean cloth. This will help to condition the blade edges.
NOTICE
Do not use engine antifreeze or a vinegar/water solution in the windshield washer reservoir.
Antifreeze can damage your car's paint, while a vinegar/water solution can damage the windshield washer pump.
Use only eommereially-evailable windshield washer fluid.
Maintenance
Main MenuTable of Contentsst6-speed Manual Transmission Fluid
The transmission should be drained and refilled with new fluid according to the time and distance recommen- dations in the maintenance schedule.
If Honda MTF is not available, you may use an API service SG, SH or SJ grade motor oil with a viscosity of SAE 10W-30 or 10W-40 as a temporary replacement. An SG grade is preferred, but an SH or SJ grade may be used if SG is not available. However, motor oil does not contain the proper additives and continued use can cause stiffer shifting. Replace as soon as convenient.
FILLER BOLT
CORRECT LEVEL
Check the fluid level with the transmission at normal operating temperature and the car sitting on level ground. Remove the transmission filler bolt and carefully feel inside the bolt hole with your finger. The fluid level should be up to the edge of the bolt hole. If it is not, add Genuine Honda Manual Transmission Fluid (MTF) until it starts to run out of the hole. Reinstall the filler bolt and tighten it securely.
Maintenance
Main MenuTable of ContentsstUse a SAE 90 viscosity hypoid gear oil, API service classified GL5 or GL6 only, in the differential.
Put a new washer on the filler bolt, then reinstall the filler bolt. Tighten it securely. Tightening torque: 33 lbf.ft (45 N.m , 4.6 kgf.m)
The differential should be drained and refilled with new fluid according to the time and distance recommendations in the maintenance schedule.
FILLER BOLT
CORRECT LEVEL
Check the fluid level with the differential at normal operating temperature and the vehicle sitting on level ground. Remove the differential fluid filler boll and washer and carefully feel inside the bolt hole with your finger. The fluid level should be up to the edge of the bolt hole. If it is not, slowly add fluid until it starts to run out of the hole.
Differential Fluid
Maintenance
Main MenuTable of ContentsstBrake and Clutch Fluid
Check the fluid level in the reser- voirs monthly. There are two reser- voirs. They are:
Brake fluid reservoir Clutch fluid reservoir
The brake fluid should be replaced according to the time and distance recommendations in the mainte- nance schedule.
Maintenance
Brake Fluid
Always use Genuine Honda DOT 3
brake fluid. If it is not available, you
should use only DOT 3 or DOT 4
fluid, from a sealed container, as a
temporary replacement. However,
the use of any non-Honda brake fluid
can cause corrosion and decrease
the life of the system. Have the
brake system flushed and refilled
with Honda DOT 3 brake fluid as
soon as possible.
Brake fluid marked DOT 5 is not compatible with your car's braking system and can cause extensive damage.
Brake System
MAX
MIN
The fluid level should be between the MIN and MAX marks on the side of the reservoir. If the level is at or below the MIN mark, your brake system needs attention. Have the brake system inspected for leaks or worn brake pads.
Main MenuTable of ContentsstClutch System
MAX
MIN
The fluid should be between the MIN and MAX marks on the side of the reservoir. If it is not, add brake fluid to bring it up to that level. Use the same fluid specified for the brake system.
Low fluid level can indicate a leak in the clutch system. Have this system inspected as soon as possible.
Clutch Fluid
Maintenance
Main MenuTable of ContentsstAir Cleaner Element
The air cleaner element should be replaced according to the time and distance recommendations in the maintenance schedule.
Follow the replacement procedure for removal and reinstallation.
Replacement
CLAMPS
AIR CLEANER ELEMENT
To replace it:
1. Unsnap the six clamps holding the
air cleaner housing cover.
2. Remove the air cleaner housing cover. Disconnect the air intake duct from the air cleaner element.
3. Remove the old air cleaner
element.
4. Carefully clean the inside of the air cleaner housing with a damp rag.
Maintenance
Main MenuTable of Contentsst5. Attach the new air cleaner
element to the duct. Install the new air cleaner element in the air cleaner housing. Make sure the pin on the edge of the element fits in the hole in the bottom of the housing.
6. Reinstall the air cleaner housing cover, snap the six clamps back into place.
Air Cleaner Element
Maintenance
Main MenuTable of ContentsstHood Latch, Spark Plugs
Hood Latch
PIVOTS
Replacement
Spark Plugs
The spark plugs in your car are a
special platinum-tipped design for
longer life. They only need to be
replaced every 7 years or 105,000
miles (168,000 km), whichever
comes first.
Clean the hood latch assembly with a mild cleaner, then lubricate it with a multipurpose grease. Lubricate all the moving parts, including the pivot. Follow the time and distance recommendations in the Maintenance Schedule. If you are not sure how to clean and grease the latch, contact your Honda dealer.
Maintenance
1. Remove the four hexagon socket
head cap bolts holding the ignition coil cover.
2. Clean up any dirt and oil that have collected around the ignition coils.
Main MenuTable of ContentsstSpark Plugs
3. Remove the bolt holding the
ignition coil and pull the ignition coil straight up slightly. Disconnect the ignition coil connector by pushing the tab and pulling the connector back. Pull the ignition coil all the way up.
4. Remove the spark plug with
a five-eighths inch (16 mm) spark plug socket.
5. Put the new spark plug into the
socket; then screw it into the hole. Screw it in by hand so you do not crossthread it.
6. Torque the spark plug. (If you do not have a torque wrench, tighten the spark plug two-thirds of a turn after it contacts the cylinder head.) Tightening torque: 18 lbf.ft (25 N.m, 2.5 kgf.m)
CONTINUED
Maintenance
Main MenuTable of ContentsstSpecifications:
NGK: DENSO:
PFR7G-11S PK22PR-L11S
Spark Plug Gap:
0.043 in
(1.1 mm
Spark Plugs
NOTICE
Tighten the spark plugs carefully. A spark plug that is too loose can overheat and damage the engine. Overtightening can cause damage to the threads in the cylinder head.
7. Install the ignition coil. Reinstall
the bolt.
8. Repeat this procedure for the
other three spark plugs.
9. Reinstall the cover on the cylinder bank. Reinstall the four hexagon socket head cap bolts.