2012 Honda Ridgeline Owners Manual

TACHOMETER

SPEEDOMETER

TEMPERATURE GAUGE

INFO (

▲

) BUTTON

SEL/RESET BUTTON

INFO (

▼

) BUTTON

MULTI-INFORMATION DISPLAY

FUEL GAUGE

U.S. model is shown.

76

Temperature Gauge This shows the temperature of the engine’s coolant. During normal operation, the pointer should rise to about the middle of the gauge. In severe driving conditions, the pointer may rise to the upper zone. If it reaches the red (hot) mark, pull safely to the side of the road. For instructions and precautions on checking the engine’s cooling system, see page

374

Fuel Gauge This shows how much fuel you have. It may show slightly more or less than the actual amount.

Avoid driving with an extremely low f uel level. Running out of f uel could cause the engine to misf ire, damaging the catalytic converter.

11/09/14 17:42:37 31SJC660_084

Information Display Onmodelswithoutnavigationsystem The information display shows the odometer, trip meter, engine oil life, outside temperature (if equipped), instant fuel economy, average fuel economy, range (estimated distance), and maintenance item code(s).

Gauges

SELECT BUTTON

Onmodelswithnavigationsystem For information about the multi- information display, see page 82

TRIP/RESET BUTTON

With the ignition switch in the ON (II) position, the information display changes as shown on the next page each time you press the SELECT button or TRIP/RESET button.

When you turn the ignition switch to the ON (II) position, your last selection is displayed.

CONTINUED

77

11/09/14 17:42:44 31SJC660_085

Gauges

INFORMATION DISPLAY

OUTSIDE TEMPERATURE INDICATOR

ODOMETER

ODOMETER

SELECT button TRIP/RESET button

TRIP METER A AVERAGE FUEL ECONOMY A

TRIP METER B AVERAGE FUEL ECONOMY B

INSTANT FUEL ECONOMY

TRIP METER A RANGE

INSTANT FUEL ECONOMY

TRIP METER B RANGE

TRIP METER A

TRIP METER B

ENGINE OIL LIFE

U.S. model is shown.

78

11/09/14 17:42:54 31SJC660_086

Odometer The odometer shows the total distance your vehicle has been driven. It measures miles in U.S. models and kilometers in Canadian models. It is illegal under U.S. federal law and Canadian provincial/ territorial regulations to disconnect, reset, or alter the odometer with the intent to change the number of miles or kilometers indicated.

TripMeter This meter shows the number of miles (U.S.) or kilometers (Canada) driven since you last reset it. There are two trip meters: Trip A and Trip B. Switch between these displays by pressing the TRIP/ RESET button repeatedly. Each trip meter works independently, so you can keep track of two different distances. To reset a trip meter, display it, and then press and hold the TRIP/RESET button until the number resets to ‘‘0.0’’.

Both trip meters will reset if the vehicle’s battery goes dead or is disconnected.

OutsideTemperatureIndicator ExceptRTandU.S.Sportmodels This shows the outside temperature in Fahrenheit (U.S. models), or in Celsius (Canadian models).

The temperature sensor is in the front bumper. The temperature reading can be affected by heat reflection from the road surface, engine heat, and the exhaust from surrounding traffic. This can cause an incorrect temperature reading when your vehicle speed is under 19 mph (30 km/h). When you start your trip, the sensor is not fully acclimatized, therefore it may take several minutes until the proper temperature is displayed.

In certain weather conditions, temperature readings near freezing

Gauges

(32°F, 0°C) could mean that ice is forming on the road surface.

If the outside temperature is incorrectly displayed, you can adjust it up to 3°C ± in Canadian models) warmer or cooler.

5°F in U.S. models (

±

The temperature must be

NOTE: stabilized before doing this procedure.

To adjust the outside temperature indicator, press and hold the TRIP/ RESET button for 10 seconds. The following sequence will appear for 1
second each: 0, 1, 2, 3, 4, 5, 4, − − − − − −

− − 1, 0 (U.S.) or 0, 1, 2, 3, 1, 0 (Canada).

2, 2,

3, 3,

5,

When the temperature reaches the desired value, release the TRIP/ RESET button. You should see the new outside temperature displayed.

CONTINUED

79

11/09/14 17:43:03 31SJC660_087

Gauges

TirePressureMonitor

TIRE PRESSURE MONITOR

The appropriate tire indicator will come on along with the low tire pressure indicator if a tire is significantly underinflated or has Low suddenly lost pressure. See Tire Pressure Indicator do if this indicator comes on.

for what to

Onmodelswithnavigationsystem This indicator is displayed as the system message on the multi- information display (see page

284

).

80

Range(EstimatedDistance) This display shows the estimated distance you can travel on the fuel remaining in the tank.

This distance is estimated from the fuel economy you have achieved over the last few miles (kilometers), so it will vary with changes in speed, traffic condition, etc.

InstantFuelEconomy This display shows the instant fuel economy you are getting.

It shows the number of mpg (U.S.) or l/100 km (Canada).

AverageFuelEconomy When either of the trip meters (trip A or B) is displayed, your vehicle’s average fuel economy since you last reset that trip meter can be shown on the information display (mpg on U.S. models and l/100 km on Canadian models). This number is updated once per 10 seconds. To see the average fuel economy, press and release the TRIP/RESET button repeatedly.

The average fuel economy will be reset when you reset the trip meter, or if the vehicle’s battery goes dead or is disconnected.

11/09/14 17:43:10 31SJC660_088

Gauges

TM

MaintenanceMinder The information display in the instrument panel shows you the engine oil life and maintenance service items when the ignition switch is in the ON (II) position. This information helps to keep you aware of the periodic maintenance your vehicle needs for continued trouble- free driving. Refer to page more information.

315

for

If the system still detects a leak in your vehicle’s evaporative emissions system, the malfunction indicator lamp (MIL) comes on. If the fuel fill cap was not already tightened, turn the engine off, and check or retighten the fuel fill cap until it clicks at least once. The MIL should go off after several days of normal driving once the cap is tightened or replaced. If the MIL does not go off, have your vehicle inspected by a dealer. For more information, see page

377

CheckFuelCapMessage Your vehicle’s onboard diagnostic system will detect a loose or missing fuel fill cap as an evaporative system leak. The first time a leak is detected a ‘‘CHECK FUEL CAP’’ message appears on the information display.

Turn the engine off, and confirm the fuel fill cap is installed. If it is, loosen it, then retighten it until it clicks at least once. The message should go off after several days of normal driving once you tighten or replace the fuel fill cap. To scroll to another display, press the SELECT button or TRIP/RESET button.

The ‘‘CHECK FUEL CAP’’ message will appear each time you restart the engine until the system turns the message off.

81

11/09/14 17:43:16 31SJC660_089

Multi-Information Display

Onmodelswithnavigationsystem The multi-information display in the instrument panel displays various information and messages when the ignition switch is in the ON (II) position. Some of the messages help you operate your vehicle more comfortably. Others help to keep you aware of the periodic maintenance your vehicle needs for continued trouble-free driving.

When you open the driver’s door, a ‘‘Welcome’’ message is shown on the multi-information display.

82

INFO (

▲

) BUTTON

With the ignition switch in the ON (II) position, the multi-information display changes as shown on the next page each time you press the INFO ( / ) button or the SEL/ RESET button.

▲ ▼

SEL/RESET BUTTON

When you turn the ignition switch to the ON (II) position, your last selection is displayed.

INFO (

▼

) BUTTON

To change the display, press the INFO ( / ) button on the dashboard repeatedly until the main menu appears (see page

▲ ▼

83

).

In the multi-information display, the system message is also displayed (see page

90

).

11/09/14 17:43:21 31SJC660_090

Multi-Information Display

(See page 84)

Trip Computer (See page 87)

Tire Pressure for each tire (See page 86)

Go to HandsFreeLink Menu (See page 86)

Go to Language Selection Menu (See page 92)

U.S. model is shown.

▲ ▼

INFO ( ) button SEL/RESET button

83

11/09/14 17:43:28 31SJC660_091

Multi-Information Display

Odometer

Trip Meter

When you reset Trip A, AVERAGE FUEL A, AVERAGE SPEED A, and ELAPSED TIME A are reset at the same time. When you reset Trip B, AVERAGE FUEL B, AVERAGE SPEED B, and ELAPSED TIME B are reset.

ODOMETER U.S. model is shown.

The odometer shows the total distance your vehicle has been driven. It measures miles in U.S. models and kilometers in Canadian models. It is illegal under U.S. federal law and Canadian provincial/ territorial regulations to disconnect, reset, or alter the odometer with the intent to change the number of miles or kilometers indicated.

U.S. model is shown.

TRIP METER

This meter shows the number of miles (U.S.) or kilometers (Canada) driven since you last reset it. There are two trip meters: Trip A and Trip B. Each trip meter works independently, so you can keep track of two different distances.

To reset a trip meter, display it, and then press and hold the SEL/RESET button until the number resets to ‘‘0.0.’’

84

11/09/14 17:43:36 31SJC660_092

Outside Temperature

OUTSIDE TEMPERATURE

U.S. model is shown.

This shows the outside temperature in Fahrenheit (U.S. models), or in Celsius (Canadian models).

The temperature sensor is in the front bumper. The temperature reading can be affected by heat reflection from the road surface, engine heat, and the exhaust from surrounding traffic. This can cause an incorrect temperature reading when your vehicle speed is under 19 mph (30 km/h). When you start your trip, the sensor is not fully acclimatized, therefore it may take several minutes until the proper temperature is displayed.

In certain weather conditions, temperature readings near freezing (32°F, 0°C) could mean that ice is forming on the road surface.

Multi-Information Display

If the outside temperature is incorrectly displayed, you can adjust it up to 3°C ± in Canadian models) warmer or cooler.

5°F in U.S. models (

±

The temperature must be

NOTE: stabilized before doing this procedure.

To adjust the outside temperature indicator, press and hold the SEL/ RESET button for 10 seconds. The following sequence will appear for 1
second each: 0, 1, 2, 3, 4, 5, 4, − − − − − −

− − 1, 0 (U.S.) or 0, 1, 2, 3, 1, 0 (Canada).

2, 2,

3, 3,

5,

When the temperature reaches the desired value, release the SEL/ RESET button. You should see the new outside temperature displayed.

85

11/09/14 17:43:43 31SJC660_093

Multi-Information Display

Engine Oil Life

Tire Pressure Monitor

Bluetooth

HandsFreeLink

U.S.

Canada

ENGINE OIL LIFE

This shows the remaining life of the engine oil. It shows 100% after the engine oil is replaced and the display is reset. The engine oil life is calculated based on engine operating conditions and accumulated engine revolutions. For more information, see page

315

86

When the tire pressure monitor is shown on the multi-information display, press the SEL/RESET button. The display changes as shown. You can see the pressure of each tire in this monitor. If one or more tires are low, inflate them to the correct pressure. For more information, see page

284

You can receive or make phone calls from your cell phone through your HandsFreeLink vehicle’s (HFL) system without touching your cell phone.

Bluetooth

11/09/14 17:43:50 31SJC660_094

Multi-Information Display

To use the system, your cell phone and the HFL system must be linked. Not all cell phones are compatible with this system. Refer to page for instructions on how to link 221
your cell phone to HFL and how to receive or make phone calls, or visit the handsfreelink.com website. In Canada, visit www.handsfreelink.ca call (888) 528-7876.

, or

Trip Computer

Average Fuel Economy/Range

Average Vehicle Speed/Elapsed Time

Instant Fuel Economy

U.S. model is shown.

▲ ▼

INFO ( ) button SEL/RESET button

CONTINUED

87

11/09/14 17:44:01 31SJC660_095

Multi-Information Display

Along with the trip meter, the trip computer calculates these values:

Average Fuel Economy Range Average Vehicle Speed Elapsed Time Instant Fuel Economy

88

ELAPSEDTIMEA/B This shows the accumulated traveling time since you last reset it. When you turn the ignition switch to the ON (II) position, ELAPSED TIME is reset.

INSTANTFUELMPG(U.S. models)/INSTANTFUELL/100km (Canadianmodels) This shows your instant fuel economy.

AVERAGEFUELA/B This shows your vehicle’s average fuel economy in mpg (U.S. models) or liter/100 km (Canadian models) since you last reset Trip A or Trip B.

RANGE This shows the estimated distance you can travel on the fuel remaining in the fuel tank. This distance is estimated from the fuel economy you received over the last several miles (U.S.) or kilometers (Canada), so it will vary with changes in speed, traffic, etc.

AVERAGESPEEDA/B This shows the average speed you are traveling in miles per hour (mph) for U.S. models or kilometers per hour (km/h) for Canadian models.

11/09/14 17:44:08 31SJC660_096

System Messages

SYSTEM MESSAGE INDICATOR

If there is a problem with your vehicle, for example the engine oil level is low or a door is not fully closed, the multi-information display will show you the problem. It does this by interrupting the current display with one or more messages.

The system message(s) triggers the appropriate indicator(s) on the instrument panel, including the system message indicator, to come on. The system message indicator does not go off until the problem(s) is corrected.

You will also hear a beep when the system message comes on for the first time.

Multi-Information Display

When there are several messages to be shown, the system switches the messages every 5 seconds. The message is shown until you push the INFO ( ) button. To see the message again, press the INFO ( after the display disappears.

) button, 5 seconds

▲ ▼

▲ ▼

or

or

Here is a list of messages shown on the multi-information display:

CONTINUED

89

11/09/14 17:44:20 31SJC660_097

Multi-Information Display

U.S.

Canada

See page

132

See page

378

See page

378

See page

376

See page

377

U.S.

Canada

U.S.

Canada

See page

11

See page

20

See page

20

See page

30

See page

31

U.S.

Canada

90

11/09/14 17:44:29 31SJC660_098

Multi-Information Display

See page

376

See page

291

See page

292

See page

283

See page

284

See page

69

See page

273

See page

332

See page

68

See page

97

See page

319

See page

252

91

11/09/14 17:44:36 31SJC660_099

Multi-Information Display

Language Selection

There are three language selections you can make: English, Spanish, and French. To choose the language you want, follow these instructions:

Press and release the INFO ( / ) ▲ ▼ button repeatedly to select the ‘‘LANGUAGE SELECTION’’ display.

Press the SEL/RESET button to see the selections.

Select the desired language by pressing the SEL/RESET button, then enter your selection by pressing and holding the SEL/RESET button.

When your selection is successfully completed, the display returns to the ‘‘LANGUAGE SELECTION’’ display.

92

11/09/19 18:03:50 31SJC660_100

INSTRUMENT PANEL BRIGHTNESS (P.98)

MOONROOF SWITCH ＊ (P.131)

MULTI-CONTROL LEVER (WINDSHIELD WIPERS/ WASHERS/TURN SIGNALS/ HEADLIGHT HIGH BEAMS) (P.94)

REMOTE AUDIO CONTROLS ＊ (P.203)

HEADLIGHT CONTROL DIAL (P.95) FOG LIGHTS ＊

(P.97)

Controls Near the Steering Wheel

TRIP/RESET BUTTON ＊ (P.76)

SELECT BUTTON ＊

(P.76)

SHIFT LEVER (P.273) VTM-4 LOCK (P.278)

▲

) BUTTON ＊

INFO ( (P.76) SEL/RESET BUTTON ＊ (P.76) INFO ( (P.76)

) BUTTON

▼

＊

HAZARD WARNING BUTTON (P.99)

CRUISE CONTROLS (P.210) INTERIOR LIGHT CONTROL SWITCH

(P.142)

SEAT HEATERS ＊ (P.126)

＊

HORN STEERING WHEEL ADJUSTMENT

(P.99)

VEHICLE STABILITY ASSIST (VSA) OFF SWITCH (P.294)

BED LIGHT SWITCH (P.144)

VOICE CONTROL BUTTONS ＊

Vehicle with navigation system is shown.

BLUETOOTH HANDSFREELINK SYSTEM VOICE CONTROL BUTTONS ＊

(P.221)

＊ ＊ ＊ ＊ ＊

1 : 2 : 3 : 4 : 5 :

To use the horn, press the center pad of the steering wheel. If equipped Only on vehicles equipped with navigation system. Refer to the navigation system manual. On models with navigation system. On models without navigation system.

93

11/09/14 17:44:55 31SJC660_101

Multi-Control Lever

1. 2. 3. 4. 5. 6. 7. 8. 9. 10.

OFF INT: Intermittent INT TIME ring LO: Low speed HI: High speed MIST Windshield washers Turn signal High beams Flash high beams

94

The multi-control lever has many functions, including windshield wipers and washers, turn signals, headlight high beams, and headlight high beam flashing.

To select a position, turn the rotary switch, push the button on the end of the lever, or push the lever up, down, forward, or backward.

OFF:

The wipers are not activated.

INT:

The length of the wiper

interval is varied automatically according to the vehicle’s speed.

Vary the delay by turning the INT TIME ring. If you turn it to the shortest delay, the wipers change to low speed when the vehicle speed exceeds 12 mph (20 km/h).

LO

−

The wipers run at low speed.

HI

−

The wipers run at high speed.

MIST:

The wipers run at high speed

until you release the lever.

Windshield Washer:

Push the button on the end of the multi- control lever. The washers spray until you release the button. The wipers run at low speed, then complete one more sweep after you release the button.

11/09/14 17:45:03 31SJC660_102

AutomaticHeatedWiperZone Your vehicle has heating wires at the bottom of the windshield to help heat the wiper blades and the windshield. If the outside temperature is near freezing, the heater turns on automatically when you turn the ignition switch to the ON (II) position. The heater turns off automatically when the outside temperature is above freezing.

This function helps to increase wiper performance when the wiper arms sit in the parked position in snowy or icy conditions.

Multi-Control Lever, Headlights

Headlight Control Dial

−

Turn Signal Push down on the multi-control lever to signal a left turn and up to signal a right turn. To signal a lane change, push lightly on the lever and hold it. The lever will return to center when you release it or complete a turn.

−

High Beams To turn on the high beams, push the multi-control lever forward until you hear a click. The blue high beam indicator will come on (see page to return to the low beams.

). Pull the lever back

67

To flash the high beams, pull the lever back lightly, then release it. The high beams will stay on as long as you hold the lever back.

1. 2. 3.

OFF Parking and indicator lights Headlights

CONTINUED

95

Automatic Lighting Off Feature The automatic lighting off feature turns off the headlights, all other exterior lights, and the instrument panel lights within 15 seconds of removing the key from the ignition switch and closing the driver’s door.

This feature activates if you leave the headlight control dial in the ‘‘ the key, then open and close the driver’s door.

’’ position, remove

’’ or ‘‘

If you remove the key from the ignition switch with the headlight control dial on, but do not open the door, the lights will turn off after 10
minutes.

The lights will turn on again when you unlock or open the driver’s door. If you unlock the door, but do not open it within 15 seconds, the lights go off. With the driver’s door open, you will hear a lights-on reminder chime.

11/09/14 17:45:10 31SJC660_103

Headlights

−

Turning the dial to ’’ position turns on the

Headlights the ‘‘ parking lights, taillights, instrument panel lights, and license plate lights.

’’

Turning the dial to the ‘‘ position turns on the headlights. If you leave the lights on and remove the key from the ignition switch, you will hear a reminder chime when you open the driver’s door.

’’ or

’’ position, the lights on

When the dial is in the ‘‘ ‘‘ indicator comes on as a reminder. This indicator stays on if you leave the lights on and turn the ignition switch to the ACCESSORY (I) or LOCK (0) position.

96

11/09/14 17:45:17 31SJC660_104

Headlights, Fog Lights

Daytime Running Lights With the headlight control dial off, the daytime running lights come on when you turn the ignition switch to the ON (II) position and release the parking brake. They remain on until you turn the ignition switch off, even if you set the parking brake.

The headlights revert to normal operation when you turn them on with the headlight control dial.

Onmodelswithnavigationsystem If you see a ‘‘CHECK DRL SYSTEM’’ message on the multi- information display, there is a problem with the daytime running light circuit. Take your vehicle to a dealer to have it checked.

Fog Lights Ifequipped

Turn the fog lights on and off by pressing the button. The indicator in the button lights to show the fog lights are on.

You can use the fog lights only when the headlights are on low beam. They will go off when you turn the headlights off or onto high beam.

97

The instrument panel brightness is dimmed when you turn the headlight control dial to the ‘‘ ‘‘ night. To cancel it, turn the instrument panel brightness control dial upward fully until you hear a click.

’’ position to reduce glare at

’’ or

If you do not insert the key in the ignition switch after opening the driver’s door, the illumination turns off about 30 seconds after you close the door.

If you insert the key but do not turn the ignition switch to the ON (II) position, the illumination turns off in about 10 seconds.

11/09/14 17:45:23 31SJC660_105

Instrument Panel Brightness

INSTRUMENT PANEL BRIGHTNESS CONTROL DIAL

The dial on the instrument panel controls the brightness of the instrument panel lights and the console compartment light. Turn the dial to adjust the brightness.

The instrument panel will illuminate when you unlock and open the driver’s door. The brightness will increase when you insert the key in the ignition switch.

98

11/09/14 17:45:32 31SJC660_106

Hazard Warning Button, Steering Wheel Adjustment

Hazard Warning Button

Steering Wheel Adjustment Make any steering wheel adjustment before you start driving.

Push the button to turn on the hazard warning lights (four-way flashers). This causes all four outside turn signals and both turn indicators in the instrument panel to flash. Use the hazard warning lights if you need to park in a dangerous area near heavy traffic, or if your vehicle is disabled.

1.

2.

Adjusting the steering wheel position while driving may cause you to lose control of the vehicle and be seriously injured in a crash.

Adjust the steering wheel only when the vehicle is stopped.

3.

Push the lever up to lock the steering wheel in position.

Push the lever on the left side of the steering column all the way down.

4.

Make sure you have securely locked the steering wheel in place by trying to move it up and down.

Move the steering wheel so it points toward your chest, not toward your face. Make sure you can see the instrument panel gauges and indicators.

99

11/09/14 17:45:39 31SJC660_107

Keys

KEY NUMBER TAG

MASTER KEY WITH REMOTE TRANSMITTER

VALET KEY (LIGHT GRAY)

You should have received a key number tag with your keys. You will need this key number if you ever have to get a lost key replaced. Use only Honda-approved key blanks.

These keys contain electronic circuits that are activated by the immobilizer system. They will not work to start the engine if the circuits are damaged.

The master key fits all the locks on your vehicle. The valet key works only in the ignition and the driver’s door lock. You can keep the glove box locked when you leave your vehicle and the valet key at a parking facility.

Protect the keys from direct sunlight, high temperature, and high humidity.

Do not drop the keys or set heavy objects on them.

Keep the keys away from liquids. If they get wet, dry them immediately with a soft cloth.

The valet key does not contain a battery. Do not try to take it apart.

You can also keep the In-Bed Trunk locked by using the main switch in the glove box (see page

118

).

100

11/09/14 17:45:47 31SJC660_108

Immobilizer System

The immobilizer system protects your vehicle from theft. If an improperly coded key (or other device) is used, the engine’s fuel system is disabled.

When you turn the ignition switch to the ON (II) position, the immobilizer system indicator should come on for a few seconds, then go off. If the indicator starts to blink, it means the system does not recognize the coding of the key. Turn the ignition switch to the LOCK (0) position, remove the key, reinsert it, and turn the ignition switch to the ON (II) position again.

The system may not recognize your key’s coding if another immobilizer key or other metal object (i.e. key chain) is near the ignition switch when you insert the key.

If the system repeatedly does not recognize the coding of your key, contact your dealer.

AsrequiredbytheFCC: ThisdevicecomplieswithPart15ofthe FCCrules.Operationissubjecttothe followingtwoconditions:(1)Thisdevice maynotcauseharmfulinterference,and (2)thisdevicemustacceptany interferencereceived,including interferencethatmaycauseundesired operation.

Do not attempt to alter this system or add other devices to it. Electrical problems could result that may make your vehicle inoperable.

Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser’s authoritytooperatetheequipment.

If you have lost your key and cannot start the engine, contact your dealer.

Always take the ignition key with you whenever you leave the vehicle alone.

ThisdevicecomplieswithIndustry CanadaStandardRSS-210. Operationissubjecttothefollowingtwo conditions:(1)thisdevicemaynotcause interference,and(2)thisdevicemust acceptanyinterferencethatmaycause undesiredoperationofthedevice.

101

11/09/14 17:45:54 31SJC660_109

Ignition Switch

The ignition switch has four positions: LOCK (0), ACCESSORY (I), ON (II), and START (III).

102

−

Use this position

START (III) only to start the engine. The switch returns to the ON (II) position when you let go of the key.

You will hear a reminder beeper if you leave the key in the ignition switch in the LOCK (0) or the ACCESSORY (I) position and open the driver’s door. Remove the key to turn off the beeper.

The shift lever must be in Park before you can remove the key from the ignition switch.

−

You can insert or

LOCK (0) remove the key only in this position. To turn the key, the shift lever must be in Park, and you must push the key in slightly.

If the front wheels are turned, the anti-theft lock may make it difficult to turn the key. Firmly turn the steering wheel to the left or right as you turn the key.

−

You can

ACCESSORY (I) operate the audio system and the accessory power sockets in this position.

−

This is the normal key

ON (II) position when driving. Several of the indicators on the instrument panel come on as a test when you turn the ignition switch from the ACCESSORY (I) to the ON (II) position.

11/09/14 17:46:02 31SJC660_110

Power Door Locks

LOCK TAB

The lock tab on each door locks and unlocks that door. Pulling up on the driver’s door lock tab only unlocks the driver’s door. To unlock the driver’s door and the In-Bed Trunk from the outside, turn the key and release it. If you turn it again, all the doors unlock.

You can open or close the side windows by using the key in the driver’s door (see page

130

).

MASTER DOOR LOCK SWITCH

To lock all doors and the In-Bed Trunk, push the front of the master door lock switch on either front door, press the lock tab down on the driver’s door, or use the key on the outside lock on the driver’s door.

Pushing the rear of either master door lock switch will unlock all of the doors and the In-Bed Trunk.

Door Locks

To lock any passenger’s door when getting out of the vehicle, push the lock tab down, and close the door. To lock the driver’s door, remove the key from the ignition switch, and push the lock tab down, or push the front of the master switch, then close the door.

LockoutPrevention With the driver’s door open and the key in the ignition, both master door lock switches will not lock, but they will unlock. The lock feature is not disabled if the driver’s door is closed. Pushing the front of the switch on the open passenger’s door will lock all doors and the In-Bed Trunk.

This vehicle has auto door locking/ unlocking features. See page for how to set them.

104

103

11/09/14 17:46:11 31SJC660_111

Door Locks

Childproof Door Locks

LOCK LEVER

The childproof door locks are designed to prevent children seated in the rear from accidentally opening the rear doors. Each rear door has a lock lever near the edge. With the lever in the LOCK position, the door cannot be opened from inside regardless of the position of the lock tab. To open the door, pull the lock tab up, and use the outside door handle.

104

Auto Door Locking/Unlocking Your vehicle has customizable settings for the doors to automatically lock and unlock. There are default settings for each of these features. You can turn off or change the settings for these features as described on the following pages. When you customize the setting, make sure your vehicle is parked safely, the engine is off, and the parking brake is applied. Make all settings before you start driving.

With the auto door locking and unlocking, the In-Bed Trunk also locks and unlocks.

Auto Door Locking The auto door locking feature has three possible settings:

The auto door locking is deactivated all the time.

The doors lock whenever you move the shift lever out of the Park (P) position.

The doors lock when the vehicle speed reaches 10 mph (15 km/h). This is the default setting.

11/09/14 17:46:21 31SJC660_112

ToturnofftheAutoDoorLock modes:

3.

Push and hold the front of the master door lock switch on the driver’s door until you hear a click (after about 5 seconds).

4.

Release the switch, and within 5
seconds, turn the ignition switch to the LOCK (0) position.

1.

Make sure the shift lever is in the Park (P) position.

2.

Turn the ignition switch to the ON (II) position, and open the driver’s door.

Door Locks

ToprogramtheParkLockmode: Locksalldoorswhentheshiftleveris movedoutofthePark(P)position.

1.

Make sure the shift lever is in the Park (P) position.

2.

Turn the ignition switch to the ON (II) position, and make sure to close the driver’s door.

CONTINUED

105

11/09/14 17:46:30 31SJC660_113

Door Locks

3.

Push and hold the front of the master door lock switch on the driver’s door. You will hear a click. Keep holding the switch until you hear another click (after about 5
seconds).

4.

Release the switch, and within 5
seconds, turn the ignition switch to the LOCK (0) position.

106

ToprogramtheDriveLockmode: Locksalldoorswhenthevehicle’sspeed reachesabout10mph(15km/h).

1.

Make sure the shift lever is in the Park (P) position.

2.

Turn the ignition switch to the ON (II) position, and make sure to close the driver’s door.

3.

4.

Push and hold the brake pedal, and move the shift lever out of the Park (P) position.

Push and hold the front of the master door lock switch on the driver’s door. You will hear a click. Keep holding the switch until you hear another click (after about 5
seconds).

5.

Release the switch and, within 5
seconds, turn the ignition switch to the ACCESSORY (I) position. Move the shift lever to the Park (P) position.

6.

Turn the ignition switch to the LOCK (0) position.

11/09/14 17:46:41 31SJC660_114

Auto Door Unlocking The auto door unlocking feature has five possible settings:

ToturnofftheAutoDoorUnlock modes:

The auto door unlocking is deactivated all the time.

The driver’s door unlocks when you move the shift lever to the Park (P) position with the brake pedal depressed. This is the default setting.

All doors unlock when you move the shift lever to the Park (P) position with the brake pedal depressed.

The driver’s door unlocks whenever you turn the ignition switch to the ACCESSORY (I) position.

All doors unlock whenever you turn the ignition switch to the ACCESSORY (I) position.

1.

Make sure the shift lever is in the Park (P) position.

2.

Turn the ignition switch to the ON (II) position, and open the driver’s door.

Door Locks

3.

Push and hold the rear of the master door lock switch on the driver’s door. You will hear a click, and after about 5 seconds, you will hear another click.

4.

Release the switch, and within 5
seconds, turn the ignition switch to the LOCK (0) position.

CONTINUED

107

11/09/14 17:46:52 31SJC660_115

Door Locks

ToprogramtheParkUnlockmode: Unlocksthedriver’sdoororalldoors whentheshiftleverismovedintothe Park(P)positionwiththebrakepedal depressed.

1.

Make sure the shift lever is in the Park (P) position.

2.

Turn the ignition switch to the ON (II) position, and make sure to close the driver’s door.

108

3.

Push and hold the rear of the master door lock switch on the driver’s door. You will hear a click. Continue to hold down the switch:

−

Until you hear another click (after about 5 seconds) to activate driver’sdoorunlock feature.

−

Or, until you hear two more clicks (after about 10 seconds) to activate the all doors unlock feature.

4.

Release the switch, and within 5
seconds, turn the ignition switch to the LOCK (0) position.

ToprogramtheIgnitionSwitch Unlockmode: Unlocksthedriver’sdoororalldoors whentheignitionswitchismovedoutof theON(II)position.

1.

Make sure the shift lever is in the Park (P) position.

2.

Turn the ignition switch to the ON (II) position, and make sure to close the driver’s door.

11/09/14 17:46:59 31SJC660_116

5.

Release the switch and, within 5
seconds, turn the ignition switch to the ACCESSORY (I) position. Move the shift lever to the Park (P) position.

6.

Turn the ignition switch to the LOCK (0) position.

3.

4.

Push and hold the brake pedal, then move the shift lever out of the Park (P) position.

Push and hold the rear of the master door lock switch on the driver’s door. You will hear a click. Continue to hold the switch:

−

Until you hear another click (after about 5 seconds) to activate the driver’s door unlock feature.

−Or, until you hear two more

clicks (after about 10 seconds) to activate the all doors unlock feature.

Door Locks

If your vehicle’s battery is removed or goes dead, the auto door lock/ unlock setting is reset to the deactivated mode.

109

11/09/14 17:47:06 31SJC660_117

Remote Transmitter

LED

LOCK BUTTON

UNLOCK BUTTON

PANIC BUTTON

−

LOCK Press this button once to lock all doors and the In-Bed Trunk. Some exterior and interior lights will flash once. When you push LOCK twice within 5
seconds, you will hear a beep to verify that the doors and In-Bed Trunk are locked and the security system (if equipped) has set. This button does not work if any door is not fully closed or the key is in the ignition switch.

110

−

Press this button once

UNLOCK to unlock the driver’s door and the In-Bed Trunk. Push it twice to unlock the remaining doors. Some exterior and interior lights will flash twice each time you push the button.

When you press the UNLOCK button, the front and rear individual map lights, depending on the interior light control switch position, will come on (see page not open any door, the lights stay on