91
2010 Ridgeline09/07/18 14:13:21 31SJC640_097
Multi-Information Display
Language Selection
There are three language selections you can make: English, Spanish, and French. To choose the language you want, follow these instructions:
Press and release the INFO ( / ) ▲ ▼ button repeatedly to select the ‘‘LANGUAGE SELECTION’’ display.
Press the SEL/RESET button to see the selections.
Select the desired language by pressing the SEL/RESET button, then enter your selection by pressing and holding the SEL/RESET button.
When your selection is successfully completed, the display returns to the ‘‘LANGUAGE SELECTION’’ display.
92
2010 Ridgeline09/07/18 14:13:32 31SJC640_098
INSTRUMENT PANEL BRIGHTNESS (P.98) MOONROOF SWITCH * (P.131) MULTI-CONTROL LEVER (WINDSHIELD WIPERS/ WASHERS/TURN SIGNALS/ HEADLIGHT HIGH BEAMS) (P.94)
REMOTE AUDIO CONTROLS * (P.203) HEADLIGHT CONTROL DIAL (P.95)
FOG LIGHTS (P.97)
*
Controls Near the Steering Wheel
TRIP/RESET BUTTON * (P.76)
SELECT BUTTON *
(P.76)
SHIFT LEVER (P.271) VTM-4 LOCK (P.276)
▲
) BUTTON *
INFO ( (P.76) SEL/RESET BUTTON * (P.76) INFO ( (P.76) PASSENGER AIRBAG OFF INDICATOR
)BUTTON
(P.31)
▼
*
HAZARD WARNING BUTTON (P.99) CRUISE CONTROLS (P.210) INTERIOR LIGHT CONTROL SWITCH
(P.142)
SEAT HEATERS * (P.126)
HORN *
STEERING WHEEL ADJUSTMENT
(P.99)
VEHICLE STABILITY ASSIST (VSA) SYSTEM OFF SWITCH
(P.292)
BED LIGHT SWITCH (P.144)
VOICE CONTROL BUTTONS *
Vehicle with navigation system is shown.
BLUETOOTH HANDSFREELINK SYSTEM VOICE CONTROL BUTTONS *
(P.221)
* * * * *
1 : 2 : 3 : 4 : 5 :
To use the horn, press the center pad of the steering wheel. If equipped Only on vehicles equipped with navigation system. Refer to the navigation system manual. On models with navigation system. On models without navigation system.
93
2010 Ridgeline09/07/18 14:13:44 31SJC640_099
Multi-Control Lever
1. 2. 3. 4. 5. 6. 7. 8. 9. 10.
OFF INT: Intermittent INT TIME ring LO: Low speed HI: High speed MIST Windshield washers Turn signal High beams Flash high beams
94
LO
−
The wipers run at low speed.
HI
−
The wipers run at high speed.
MIST:
The wipers run at high speed until you release the lever.
Windshield Washer:
Push the button on the end of the multi-control lever. The washers spray until you release the button. The wipers run at low speed, then complete one more sweep after you release the button.
The multi-control lever has many functions, including windshield wipers and washers, turn signals, headlight high beams, and headlight high beam flashing.
To select a position, turn the rotary switch, push the button on the end of the lever, or push the lever up, down, forward, or backward.
OFF:
The wipers are not activated.
INT:
The length of the wiper interval is varied automatically according to the vehicle’s speed.
Vary the delay by turning the INT TIME ring. If you turn it to the shortest delay, the wipers change to low speed when the vehicle speed exceeds 12 mph (20 km/h).
2010 Ridgeline09/07/18 14:13:55 31SJC640_100
AutomaticHeatedWiperZone Your vehicle has heating wires at the bottom of the windshield to help heat the wiper blades and the windshield. If the outside temperature is near freezing, the heater turns on automatically when you turn the ignition switch to the ON (II) position. The heater turns off automatically when the outside temperature is above freezing.
This function helps to increase wiper performance when the wiper arms sit in the parked position in snowy or icy conditions.
Multi-Control Lever, Headlights
Headlight Control Dial
−
Turn Signal Push down on the multi-control lever to signal a left turn and up to signal a right turn. To signal a lane change, push lightly on the lever and hold it. The lever will return to center when you release it or complete a turn.
−
High Beams To turn on the high beams, push the multi-control lever forward until you hear a click. The blue high beam indicator will come on (see page to return to the low beams.
). Pull the lever back
67
To flash the high beams, pull the lever back lightly, then release it. The high beams will stay on as long as you hold the lever back.
1. 2. 3.
OFF Parking and indicator lights Headlights
CONTINUED
95
2010 RidgelineAutomatic Lighting Off Feature The automatic lighting off feature turns off the headlights, all other exterior lights, and the instrument panel lights within 15 seconds of removing the key from the ignition switch and closing the driver’s door.
This feature activates if you leave the headlight control dial in the ‘‘ the key, then open and close the driver’s door.
’’ position, remove
’’ or ‘‘
If you remove the key from the
ignition switch with the headlight
control dial on, but do not open the
door, the lights will turn off after 10
minutes.
The lights will turn on again when you unlock or open the driver’s door. If you unlock the door, but do not open it within 15 seconds, the lights go off. With the driver’s door open, you will hear a lights-on reminder chime.
09/07/18 14:14:05 31SJC640_101
Headlights
−
Turning the dial to ’’ position turns on the
Headlights the ‘‘ parking lights, taillights, instrument panel lights, and license plate lights.
’’
Turning the dial to the ‘‘ position turns on the headlights. If you leave the lights on and remove the key from the ignition switch, you will hear a reminder chime when you open the driver’s door.
’’ or
’’ position, the lights on
When the dial is in the ‘‘ ‘‘ indicator comes on as a reminder. This indicator stays on if you leave the lights on and turn the ignition switch to the ACCESSORY (I) or LOCK (0) position.
96
2010 Ridgeline09/07/18 14:14:15 31SJC640_102
Headlights, Fog Lights
Daytime Running Lights With the headlight control dial off, the daytime running lights come on when you turn the ignition switch to the ON (II) position and release the parking brake. They remain on until you turn the ignition switch off, even if you set the parking brake.
The headlights revert to normal operation when you turn them on with the headlight control dial.
Onmodelswithnavigationsystem If you see a ‘‘CHECK DRL SYSTEM’’ message on the multi- information display, there is a problem with the daytime running light circuit. Take your vehicle to a dealer to have it checked.
Fog Lights Ifequipped
Turn the fog lights on and off by pressing the button. The indicator in the button lights to show the fog lights are on.
You can use the fog lights only when the headlights are on low beam. They will go off when you turn the headlights off or onto high beam.
97
2010 RidgelineThe instrument panel brightness is dimmed when you turn the headlight control dial to the ‘‘ ‘‘ night. To cancel it, turn the instrument panel brightness control dial upward fully until you hear a click.
’’ position to reduce glare at
’’ or
If you do not insert the key in the ignition switch after opening the driver’s door, the illumination turns off about 30 seconds after you close the door.
If you insert the key but do not turn the ignition switch to the ON (II) position, the illumination turns off in about 10 seconds.
09/07/18 14:14:23 31SJC640_103
Instrument Panel Brightness
INSTRUMENT PANEL BRIGHTNESS CONTROL DIAL
The dial on the instrument panel controls the brightness of the instrument panel lights and the console compartment light. Turn the dial to adjust the brightness.
The instrument panel will illuminate when you unlock and open the driver’s door. The brightness will increase when you insert the key in the ignition switch.
98
2010 Ridgeline09/07/18 14:14:34 31SJC640_104
Hazard Warning Button, Steering Wheel Adjustment
Hazard Warning Button
Steering Wheel Adjustment Make any steering wheel adjustment before you start driving.
Push the button to turn on the hazard warning lights (four-way flashers). This causes all four outside turn signals and both turn indicators in the instrument panel to flash. Use the hazard warning lights if you need to park in a dangerous area near heavy traffic, or if your vehicle is disabled.
1.
2.
Adjusting the steering wheel position while driving may cause you to lose control of the vehicle and be seriously injured in a crash.
Adjust the steering wheel only when the vehicle is stopped.
3.
Push the lever up to lock the steering wheel in position.
Push the lever on the left side of the steering column all the way down.
4.
Make sure you have securely locked the steering wheel in place by trying to move it up and down.
Move the steering wheel so it points toward your chest, not toward your face. Make sure you can see the instrument panel gauges and indicators.
99
2010 Ridgeline09/07/18 14:14:44 31SJC640_105
Keys
KEY NUMBER TAG
MASTER KEY WITH REMOTE TRANSMITTER
VALET KEY (LIGHT GRAY)
You should have received a key number tag with your keys. You will need this key number if you ever have to get a lost key replaced. Use only Honda-approved key blanks.
These keys contain electronic circuits that are activated by the immobilizer system. They will not work to start the engine if the circuits are damaged.
The master key fits all the locks on your vehicle. The valet key works only in the ignition and the driver’s door lock. You can keep the glove box locked when you leave your vehicle and the valet key at a parking facility.
Protect the keys from direct sunlight, high temperature, and high humidity.
Do not drop the keys or set heavy objects on them.
Keep the keys away from liquids. If they get wet, dry them immediately with a soft cloth.
The valet key does not contain a battery. Do not try to take it apart.
You can also keep the In-Bed Trunk locked by using the main switch in the glove box (see page
118
).
100
2010 Ridgeline09/07/18 14:14:55 31SJC640_106
Immobilizer System
The immobilizer system protects your vehicle from theft. If an improperly coded key (or other device) is used, the engine’s fuel system is disabled.
When you turn the ignition switch to the ON (II) position, the immobilizer system indicator should come on for a few seconds, then go off. If the indicator starts to blink, it means the system does not recognize the coding of the key. Turn the ignition switch to the LOCK (0) position, remove the key, reinsert it, and turn the ignition switch to the ON (II) position again.
The system may not recognize your key’s coding if another immobilizer key or other metal object (i.e. key chain) is near the ignition switch when you insert the key.
If the system repeatedly does not recognize the coding of your key, contact your dealer.
AsrequiredbytheFCC: ThisdevicecomplieswithPart15ofthe FCCrules.Operationissubjecttothe followingtwoconditions:(1)Thisdevice maynotcauseharmfulinterference,and (2)thisdevicemustacceptany interferencereceived,including interferencethatmaycauseundesired operation.
Do not attempt to alter this system or add other devices to it. Electrical problems could result that may make your vehicle inoperable.
Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser’s authoritytooperatetheequipment.
If you have lost your key and cannot start the engine, contact your dealer.
Always take the ignition key with you whenever you leave the vehicle alone.
ThisdevicecomplieswithIndustry CanadaStandardRSS-210. Operationissubjecttothefollowingtwo conditions:(1)thisdevicemaynotcause interference,and(2)thisdevicemust acceptanyinterferencethatmaycause undesiredoperationofthedevice.
101
2010 Ridgeline09/07/18 14:15:05 31SJC640_107
Ignition Switch
The ignition switch has four positions: LOCK (0), ACCESSORY (I), ON (II), and START (III).
102
−
Use this position
START (III) only to start the engine. The switch returns to the ON (II) position when you let go of the key.
You will hear a reminder beeper if you leave the key in the ignition switch in the LOCK (0) or the ACCESSORY (I) position and open the driver’s door. Remove the key to turn off the beeper.
The shift lever must be in Park before you can remove the key from the ignition switch.
−
You can insert or
LOCK (0) remove the key only in this position. To turn the key, the shift lever must be in Park, and you must push the key in slightly.
If the front wheels are turned, the anti-theft lock may make it difficult to turn the key. Firmly turn the steering wheel to the left or right as you turn the key.
−
You can
ACCESSORY (I) operate the audio system and the accessory power sockets in this position.
−
This is the normal key
ON (II) position when driving. Several of the indicators on the instrument panel come on as a test when you turn the ignition switch from the ACCESSORY (I) to the ON (II) position.
2010 Ridgeline09/07/18 14:15:16 31SJC640_108
Power Door Locks
LOCK TAB
The lock tab on each door locks and unlocks that door. Pulling up on the driver’s door lock tab only unlocks the driver’s door. To unlock the driver’s door and the In-Bed Trunk from the outside, turn the key and release it. If you turn it again, all the doors unlock.
You can open or close the side windows by using the key in the driver’s door (see page
130
).
MASTER DOOR LOCK SWITCH
To lock all doors and the In-Bed Trunk, push the front of the master door lock switch on either front door, press the lock tab down on the driver’s door, or use the key on the outside lock on the driver’s door.
Pushing the rear of either master door lock switch will unlock all of the doors and the In-Bed Trunk.
Door Locks
To lock any passenger’s door when getting out of the vehicle, push the lock tab down, and close the door. To lock the driver’s door, remove the key from the ignition switch, and push the lock tab down, or push the front of the master switch, then close the door.
LockoutPrevention With the driver’s door open and the key in the ignition, both master door lock switches will not lock, but they will unlock. The lock feature is not disabled if the driver’s door is closed. Pushing the front of the switch on the open passenger’s door will lock all doors and the In-Bed Trunk.
This vehicle has auto door locking/ unlocking features. See page for how to set them.
104
103
2010 Ridgeline09/07/18 14:15:29 31SJC640_109
Door Locks
Childproof Door Locks
LOCK LEVER
The childproof door locks are designed to prevent children seated in the rear from accidentally opening the rear doors. Each rear door has a lock lever near the edge. With the lever in the LOCK position, the door cannot be opened from inside regardless of the position of the lock tab. To open the door, pull the lock tab up, and use the outside door handle.
104
Auto Door Locking/Unlocking Your vehicle has customizable settings for the doors to automatically lock and unlock. There are default settings for each of these features. You can turn off or change the settings for these features as described on the following pages. When you customize the setting, make sure your vehicle is parked safely, the engine is off, and the parking brake is applied. Make all settings before you start driving.
With the auto door locking and unlocking, the In-Bed Trunk also locks and unlocks.
Auto Door Locking The auto door locking feature has three possible settings:
The auto door locking is deactivated all the time.
The doors lock whenever you move the shift lever out of the Park (P) position.
The doors lock when the vehicle speed reaches 9 mph (15 km/h). This is the default setting.
2010 Ridgeline09/07/18 14:15:42 31SJC640_110
ToturnofftheAutoDoorLock modes:
3.
Push and hold the front of the master door lock switch on the driver’s door until you hear a click (after about 5 seconds).
4.
Release the switch, and within 5
seconds, turn the ignition switch
to the LOCK (0) position.
1.
Make sure the shift lever is in the Park (P) position.
2.
Turn the ignition switch to the ON (II) position, and open the driver’s door.
Door Locks
ToprogramtheParkLockmode: Locksalldoorswhentheshiftleveris movedoutofthePark(P)position.
1.
Make sure the shift lever is in the Park (P) position.
2.
Turn the ignition switch to the ON (II) position, and make sure to close the driver’s door.
CONTINUED
105
2010 Ridgeline09/07/18 14:15:54 31SJC640_111
Door Locks
3.
Push and hold the front of the
master door lock switch on the
driver’s door. You will hear a click.
Keep holding the switch until you
hear another click (after about 5
seconds).
4.
Release the switch, and within 5
seconds, turn the ignition switch
to the LOCK (0) position.
106
ToprogramtheDriveLockmode: Locksalldoorswhenthevehicle’sspeed reachesabout9mph(15km/h).
1.
Make sure the shift lever is in the Park (P) position.
2.
Turn the ignition switch to the ON (II) position, and make sure to close the driver’s door.
3.
4.
Push and hold the brake pedal, and move the shift lever out of the Park (P) position.
Push and hold the front of the
master door lock switch on the
driver’s door. You will hear a click.
Keep holding the switch until you
hear another click (after about 5
seconds).
5.
Release the switch and, within 5
seconds, turn the ignition switch
to the ACCESSORY (I) position.
Move the shift lever to the Park
(P) position.
6.
Turn the ignition switch to the LOCK (0) position.
2010 Ridgeline09/07/18 14:16:09 31SJC640_112
Auto Door Unlocking The auto door unlocking feature has five possible settings:
ToturnofftheAutoDoorUnlock modes:
The auto door unlocking is deactivated all the time.
The driver’s door unlocks when you move the shift lever to the Park (P) position with the brake pedal depressed. This is the default setting.
All doors unlock when you move the shift lever to the Park (P) position with the brake pedal depressed.
The driver’s door unlocks whenever you turn the ignition switch to the ACCESSORY (I) position.
All doors unlock whenever you turn the ignition switch to the ACCESSORY (I) position.
1.
Make sure the shift lever is in the Park (P) position.
2.
Turn the ignition switch to the ON (II) position, and open the driver’s door.
Door Locks
3.
Push and hold the rear of the master door lock switch on the driver’s door. You will hear a click, and after about 5 seconds, you will hear another click.
4.
Release the switch, and within 5
seconds, turn the ignition switch
to the LOCK (0) position.
CONTINUED
107
2010 Ridgeline09/07/18 14:16:23 31SJC640_113
Door Locks
ToprogramtheParkUnlockmode: Unlocksthedriver’sdoororalldoors whentheshiftleverismovedintothe Park(P)positionwiththebrakepedal depressed.
1.
Make sure the shift lever is in the Park (P) position.
2.
Turn the ignition switch to the ON (II) position, and make sure to close the driver’s door.
108
3.
Push and hold the rear of the master door lock switch on the driver’s door. You will hear a click. Continue to hold down the switch:
−
Until you hear another click (after about 5 seconds) to activate driver’sdoorunlock feature.
−
Or, until you hear two more clicks (after about 10 seconds) to activate the all doors unlock feature.
4.
Release the switch, and within 5
seconds, turn the ignition switch
to the LOCK (0) position.
ToprogramtheIgnitionSwitch Unlockmode: Unlocksthedriver’sdoororalldoors whentheignitionswitchismovedoutof theON(II)position.
1.
Make sure the shift lever is in the Park (P) position.
2.
Turn the ignition switch to the ON (II) position, and make sure to close the driver’s door.
2010 Ridgeline09/07/18 14:16:33 31SJC640_114
5.
Release the switch and, within 5
seconds, turn the ignition switch
to the ACCESSORY (I) position.
Move the shift lever to the Park
(P) position.
6.
Turn the ignition switch to the LOCK (0) position.
3.
4.
Push and hold the brake pedal, then move the shift lever out of the Park (P) position.
Push and hold the rear of the master door lock switch on the driver’s door. You will hear a click. Continue to hold the switch:
−
Until you hear another click (after about 5 seconds) to activate the driver’s door unlock feature.
−Or, until you hear two more
clicks (after about 10 seconds) to activate the all doors unlock feature.
Door Locks
If your vehicle’s battery is removed or goes dead, the auto door lock/ unlock setting is reset to the deactivated mode.
109
2010 Ridgeline09/07/18 14:16:42 31SJC640_115
Remote Transmitter
LED
LOCK BUTTON
UNLOCK BUTTON
PANIC BUTTON
−
LOCK
Press this button once to
lock all doors and the In-Bed Trunk.
Some exterior and interior lights will
flash once.
When you push LOCK twice within 5
seconds, you will hear a beep to
verify that the doors and In-Bed
Trunk are locked and the security
system (if equipped) has set. This
button does not work if any door is
not fully closed or the key is in the
ignition switch.
110
−
Press this button once
UNLOCK to unlock the driver’s door and the In-Bed Trunk. Push it twice to unlock the remaining doors. Some exterior and interior lights will flash twice each time you push the button.
When you press the UNLOCK button, the front and rear individual map lights, depending on the interior light control switch position, will come on (see page not open any door, the lights stay on for about 30 seconds, then go out. If you relock the doors and the In-Bed Trunk with the remote transmitter before 30 seconds have elapsed, the lights will go off immediately.
). If you do
142
If you do not open any door within 30
seconds, the doors automatically
relock, and the security system sets
(if equipped). The UNLOCK button
does not work when the key is in the
ignition switch.
You can also open all side windows
from outside the vehicle with the
130
remote transmitter (see page
).
−
Press and hold this
PANIC button for about 1 second to attract attention; the horn will sound, and the exterior lights will flash for about 30 seconds. To cancel panic mode, press any other button on the remote transmitter, or turn the ignition switch to the ON (II) position. Panic mode does not work when the key is in the ignition switch.
2010 Ridgeline09/07/18 14:16:56 31SJC640_116
Remote Transmitter Care
Avoid dropping or throwing the transmitter.
Protect the transmitter from extreme temperature.
Do not immerse the transmitter in any liquid.
If you lose a transmitter, the replacement needs to be reprogrammed by your dealer.
Remote Transmitter
Replacing the Transmitter Battery
BATTERY
SCREW
If it takes several pushes on the
button to lock or unlock the doors,
replace the battery as soon as
possible.
Battery type: CR1616
2.
3.
To replace the battery:
1.
Remove the screw at the base of the transmitter with a small Phillips-head screwdriver.
Separate the transmitter by prying its middle seam with your fingernail.
Inside the transmitter, separate the inner cover from the keypad by releasing the two tabs on the cover.
CONTINUED
111
2010 Ridgeline09/07/18 14:17:03 31SJC640_117
Remote Transmitter
AsrequiredbytheFCC: ThisdevicecomplieswithPart15ofthe FCCrules.Operationissubjecttothe followingtwoconditions:(1)Thisdevice maynotcauseharmfulinterference,and (2)thisdevicemustacceptany interferencereceived,including interferencethatmaycauseundesired operation.
Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser’s authoritytooperatetheequipment.
ThisdevicecomplieswithIndustry CanadaStandardRSS-210. Operationissubjecttothefollowingtwo conditions:(1)thisdevicemaynotcause interference,and(2)thisdevicemust acceptanyinterferencethatmaycause undesiredoperationofthedevice.
4.
Remove the old battery from the back of the inner cover, and insert a new battery into the back of the cover with the
side facing down.
+
An improperly disposed of battery can hurt the environment. Always confirm local regulations for battery disposal.
5.
Install the parts in reverse order.
112
2010 Ridgeline09/07/18 14:17:14 31SJC640_118
Before you open the tailgate a different way (dropped open, and then swung open), make sure it is fully closed.
Make sure all passengers and objects are clear of the tailgate before opening and closing it, and make sure the tailgate is closed securely before driving.
You can open the tailgate two different ways:
Drop it open by using the upper handle.
Swing it open by using the right lower handle.
NOTE: As a safety feature, the upper handle is disabled if you do not fully close the tailgate after it is swung open. And the lower handle is disabled if you do not fully close the tailgate after it is dropped open.
Dual-Action Tailgate
To Drop Open the Tailgate
UPPER HANDLE
To drop open the tailgate, pull up the upper handle, then pull down the tailgate. To close the tailgate, push firmly up until it latches.
CONTINUED
113
2010 Ridgeline09/07/18 14:17:23 31SJC640_119
Dual-Action Tailgate
The dropped open tailgate can be used as an extended pickup bed. Make sure to secure the items in the pickup bed, and do not exceed the maximum allowable weight on the tailgate (see page
263
).
To Swing Open the Tailgate
To turn the bed lights on or off, use the bed light switch on the dashboard (see page ).
144
HANDLE
To swing open the tailgate, first make sure it is fully closed, then pull up the right lower handle, and swing the tailgate to the left. To close, swing the tailgate back, and push it firmly until it is latched.
Before opening or closing the tailgate, check that passengers, especially children, are not in the tailgate’s path.
114
Do not drive with the tailgate swung open. This could damage the tailgate.
Swinging the tailgate open or closed while anyone is in its path can cause serious injury.
Make sure all passengers are clear of the tailgate’s path before opening or closing it.
2010 Ridgeline09/07/18 14:17:37 31SJC640_120
Do not allow anyone to hang on the swung open tailgate. This could damage the tailgate.
Do not leave the tailgate swung open. The tailgate may swing and shut accidentally. This could cause serious injuries.
The bed lights come on when you swing open the tailgate. You can also turn the bed lights on or off by pushing the bed light switch on the dashboard (see page
144
).
Dual-Action Tailgate
If you do not fasten the seat belt, you first hear the seat belt reminder alarm, then the tailgate reminder beeper sounds.
The indicator does not monitor the tailgate when it is dropped open.
Loading Cargo See page for information on cargo loading and weight limits.
259
You can also store and lock items in the In-Bed Trunk (see page
116
).
TailgateOpenIndicator
Onmodelswithoutnavigationsystem This indicator is in the door and tailgate open monitor on the instrument panel. It comes on when the tailgate is swung open or it is not completely closed. This indicator works even if the key is not in the ignition switch.
If the tailgate is swung open or not closed tightly when the ignition switch is in the ON (II) position, you will hear six beeps and see the indicator blinking. The indicator stays on until you close the tailgate. The beeper also sounds and the indicator blinks when you move the shift lever out of the Park or neutral position.
Onmodelswithnavigationsystem The tailgate open indicator appears on the multi-information display (see page
11
).
115
2010 Ridgeline09/07/18 14:17:50 31SJC640_121
In-Bed Trunk
RELEASE BUTTON
You can open the In-Bed Trunk two different ways:
Push the release button on the lower right side of the In-Bed Trunk lid when the driver’s door is unlocked.
Use the master key to open the In-Bed Trunk when the driver’s door is locked.
116
If your vehicle’s battery is disconnected or goes dead, the release button on the In-Bed Trunk lid is disabled. To open the In-Bed Trunk, use the master key.
The bed lights come on when you open the In-Bed Trunk. You can also turn the bed lights on or off by pushing the bed light switch on the dashboard (see page
144
).
To close the In-Bed Trunk, lower the lid, then press down on the back edge.
When the In-Bed Trunk is closed securely, it can be locked or unlocked along with the power door locks (see page
103
).
You can store items in the In-Bed
Trunk up to 300 lbs (136 kg). Do not
exceed this weight limit, or you may
damage the In-Bed Trunk. See page
259
for information on loading cargo
and weight limits.
To store items separately in the In-Bed Trunk, optional divider guides are available from your dealer.
2010 Ridgeline09/07/18 14:18:02 31SJC640_122
To avoid damaging the key and key cylinder of the In-Bed Trunk lid, do not close the tailgate when the key is in the lid.
To avoid damaging the seal on the In-Bed Trunk lid, remove any debris from the lid’s mating surface before you close it.
Emergency Opener
In-Bed Trunk
To avoid damaging the In-Bed Trunk lid, and to prevent items from being thrown about the vehicle and possibly hurting someone in a crash or sudden stop, be sure the In-Bed Trunk lid is securely closed before driving away.
To avoid damaging the bottom of the In-Bed Trunk, do not drive over large obstacles, and do not use it as a jacking point to raise the vehicle.
In-Bed Trunk Open Indicator
This indicator on the instrument panel reminds you that the In-Bed Trunk is open (see page
75
).
RELEASE LEVER
As a safety feature, your vehicle has a release lever on the latch of the In-Bed Trunk lid so it can be opened from the inside. To open the In-Bed Trunk, push the release lever in the direction of the arrow.
Parents should decide if their children should be shown how to use this feature. For more information about child safety, see page
38
117
2010 Ridgeline09/07/18 14:18:13 31SJC640_123
In-Bed Trunk
In-Bed Trunk Main Switch
Washing the In-Bed Trunk
Cargo Hooks
MAIN SWITCH
CARGO HOOKS
To protect items in the In-Bed Trunk, you can disable its release button by turning off the main switch in the glove box and locking the glove box with the master key.
Even if the main switch is in the OFF position, you can open the In-Bed Trunk with the master key.
118
DRAIN PLUG
You can wash the inside of the In-Bed Trunk with a water and mild detergent solution, and a soft brush or cloth.
To drain water from the In-Bed Trunk, remove the drain plug by turning it counterclockwise.
When you are finished washing the In-Bed Trunk, dry it with a soft cloth, and reinstall the drain plug.
There are two cargo hooks for plastic grocery bags at the back of the In-Bed Trunk. They are designed to hold light items. Heavy objects may damage the hooks.
2010 Ridgeline09/07/18 14:18:21 31SJC640_124
The front passenger’s seat in all models adjusts manually.
Manual Seat Adjustments OnRTandCanadianDXandVPmodels Seepages forimportantsafety informationandwarningsabouthowto properlypositiontheseatsandseat- backs.
13 15
−
Make all seat adjustments before you start driving.
Seats
To adjust the seat forward or backward, pull up on the bar under the seat cushion’s front edge. Move the seat to the desired position, and release the bar. Try to move the seat to make sure it is locked in position.
CONTINUED
119
2010 Ridgeline09/07/18 14:18:29 31SJC640_125
Seats
Driver’s Seat Manual Height Adjustment Make all seat adjustments before you start driving.
Make sure to pull the lever upward or downward to its full range.
To change the seat-back angle of the front seat, pull up the lever on the outside of the seat bottom.
Once a seat is adjusted correctly, rock it back and forth to make sure it is locked in position.
120
OnRTandCanadianDXandVPmodels The height of your driver’s seat is adjustable. To raise the seat, repeatedly pull up the lever on the outside of the seat cushion. To lower the seat, push the lever down repeatedly.
2010 Ridgeline09/07/18 14:18:44 31SJC640_126
Power Seat Adjustments OnRTS,RTLandCanadianEX-L models Seepages forimportantsafety informationandwarningsabouthowto properlypositiontheseatsandseat- backs.
13 15
−
The controls for the power adjustable driver’s seat are on the outside edge of the seat bottom. You can adjust the seat with the ignition switch in any position. Make all seat adjustments before you start driving.
Moves the seat forward and backward.
Moves the front of the seat up or down.
Raises or lowers the seat.
Seats
Moves the whole seat up and forward, or down and backward. The front of the seat also tilts up or down at the same time.
Adjusts the seat-back angle forward or backward.
Increases or decreases the lumbar support. (RTL and Canadian EX-L models)
121
2010 Ridgeline09/07/18 14:18:55 31SJC640_127
Seats
Armrests
FRONT
REAR
To use the console lid as an armrest, slide it to the desired position.
Make sure your passenger’s hands and fingers are away from the armrest before moving it.
The rear seat armrest is in the center of the rear seats. Pivot it down to use it.
122
Head Restraints Seepage forimportantsafety informationandawarningabout improperlypositioningheadrestraints.
15
Your vehicle is equipped with head restraints in all seating positions to help protect you and your passengers from the likelihood of whiplash and other injuries.
2010 Ridgeline09/07/18 14:19:05 31SJC640_128
Seats
CUSHION
Rear Center Position
CUSHION
SEAT- BACK
They are most effective when you adjust them so the center of the back of the occupant’s head rests against the center of the restraint.
LEGS
RELEASE BUTTON
LEGS
RELEASE BUTTON
AdjustingtheHeadRestraint The head restraints adjust for height. You need both hands to adjust the restraint. Do not attempt to adjust it while driving. To raise it, pull upward. To lower the restraint, push the release button sideways, and push the restraint down.
When a passenger is seated in the rear center seating position, make sure the center head restraint is properly positioned.
CONTINUED
123
2010 Ridgeline09/07/18 14:19:17 31SJC640_129
Seats
RemovingtheHeadRestraint To remove a head restraint for cleaning or repair, pull it up as far as it will go. Push the release button, then pull the restraint out of the seat- back.
Failure to reinstall the head restraints can result in severe injury during a crash.
Always replace the head restraints before driving.
When reinstalling a head restraint, put the legs back in place. Then adjust it to the appropriate height while pressing the release button.
Make sure the head restraint locks in position when you reinstall it.
124
This reduces the distance between the restraint and the occupant’s head. It also helps protect the occupants against the likelihood of whiplash and injuries to the neck and upper spine.
After a collision, the activated restraint should return to its normal position.
If the restraints do not return to their normal position, or in the event of a severe collision, have the vehicle inspected by a Honda dealer.
ActiveHeadRestraints
The driver’s and front passenger’s seats have active head restraints. If the vehicle is struck severely from the rear, the occupant properly secured with the seat belt will be pushed against the seat-back and the head restraint will automatically move forward.
2010 Ridgeline09/07/18 14:19:28 31SJC640_130
Folding the Rear Seats The left and right rear seat cushions can be lifted up separately to make room for cargo.
Remove any items from the seat before you fold up the seat cushion.
For a head restraint system to work properly:
Do not hang any items on the head restraints, or from the restraint legs.
Do not place any object between an occupant and the seat-back.
Install each restraint in its proper location.
Only use genuine Honda replacement head restraints.
Seats
To fold a rear seat cushion, pull up the lever on the outside of the cushion. The seat cushion pops up, and the seat legs store underneath it. Push the cushion firmly against the seat-back to lock it in place.
CONTINUED
125
2010 Ridgeline09/07/18 14:19:40 31SJC640_131
Seats, Seat Heaters
LEGS
FLOOR GUIDE
To return the seat cushion to its original position, pull the lever outward, then push down the seat cushion slowly.
Make sure the seat cushion is locked securely and the seat legs are positioned properly in the floor guide.
126
Make sure all items in the cargo area are secured. Loose items can fly forward and cause injury if you have Carrying Cargo to brake hard (See on page
259
).
You can also store small items under the rear seats. Make sure to secure the items so they will not shift while you are driving.
Seat Heaters
Passenger’s Seat
HEATERS
Driver’s Seat
Ifequipped Both front seats are equipped with seat heaters. Because of the sensors for the side airbag cutoff system, there is no heater in the passenger’s seat-back. The ignition switch must be in the ON (II) position to use the heaters.
2010 Ridgeline09/07/18 14:19:48 31SJC640_132
SEAT HEATER SWITCHES
In the HI setting, the heater turns off when the seat gets warm, and turns back on after the seat’s temperature drops.
In the LO setting, the heater runs continuously. It does not cycle with temperature changes.
Push the top of the switch, HI, to rapidly heat up the seat. After the seat reaches a comfortable temperature, select LO by pushing the bottom of the switch. This will keep the seat warm.
Seat Heaters
Follow these precautions when using the seat heaters:
Use the HI setting only to heat the seats quickly, because it draws large amounts of current from the battery.
If the engine is left idling for an extended period, do not use the seat heaters, even on the LO setting. It can weaken the battery, causing hard starting.
127
2010 Ridgeline09/07/18 14:19:56 31SJC640_133
Power Windows
DRIVER’S WINDOW SWITCH
MAIN SWITCH
The windows operate for up to 10
minutes after you turn off the
ignition switch. Opening either front
door cancels this function.
BACK WINDOW