2000 Honda Prelude Owners Manual

BULB

SOCKET

SCREW

FRONT SIDE MARKER ASSEMBLY

1. Use a Phillips-head screwdriver to

remove the side marker assembly's mounting screw.

3. Remove the socket from the side

marker assembly by turning it one- quarter turn counterclockwise.

2. Remove the side marker assembly

from the bumper.

4. Pull the bulb straight out of its

socket.

Push the new bulb straight into the socket until it bottoms.

Lights

5. Insert the socket back into the side marker assembly. Turn it clockwise to lock it in place.

6. Test the side marker to make sure

the new bulb is working.

7. Put the side marker assembly into the bumper. Make sure the tab on the side marker assembly fits into the bumper slot. Tighten the mounting screw.

Maintenance

Main MenuTable of ContentsstLights

Replacing a Front Turn Signal Light Bulb

TURN SIGNAL ASSEMBLY

BULB

5. Insert the socket back into the

turn signal assembly. Turn it clockwise to lock it in place.

6. Test the lights to make sure the

new bulb is working.

7. Put the turn signal assembly into

the bumper. Make sure the tab on the turn signal assembly fits into the bumper slot. Tighten the mounting screw.

SCREW

SOCKET

1. Use a Phillips-head screwdriver to loosen the turn signal assembly's mounting screw.

3. Remove the socket from the turn signal assembly by turning it one- quarter turn counterclockwise.

2. Remove the turn signal assembly

from the bumper.

4. Pull the bulb straight out of its

socket. Push the new bulb straight into the socket until it bottoms.

Maintenance

Main MenuTable of ContentsstReplacing Rear Bulbs

Lights

1. Open the trunk.

2. Undo the fastener on the side of

the trunk lining by pushing on the center of the fastener's head until it pops in. Pull the lining back.

3. Determine which of the five bulbs is burned out: stop/taillight, turn signal light, side marker light, back-up light, or taillight.

5. Pull the bulb straight out of its

socket. Push the new bulb straight into the socket until it bottoms.

4. Remove the socket by turning it

one-quarter turn counterclockwise.

CONTINUED

Maintenance

Main MenuTable of ContentsstLights

6. Reinstall the socket into the light assembly by turning it clockwise until it locks.

7. Test the lights to make sure the

new bulb is working.

8. Reinstall the trunk lining.

9. Reset the fastener by pushing on the pointed end until it pops back almost flush with the fingers on the housing.

10. Put the fastener in the hole in the side of the trunk lining and push on the center until it locks (the center is flush with the head).

Maintenance

Main MenuTable of ContentsstReplacing a High-mount Brake Light Bulb (Except Type SH model)

HIGH-MOUNT BRAKE LIGHT ASSEMBLY

1. Remove the high-mount brake

light assembly by pushing it slightly toward the rear windshield and sliding it out of the rear shelf.

2. Remove the socket from the light

assembly by turning it one-quarter turn counterclockwise.

3. Pull the bulb straight out of its

socket. Push the new bulb straight into the socket until it bottoms.

Lights

4. Reinstall the socket. Turn it

clockwise until it locks.

5. Test the lights to make sure the

new bulb is working.

6. Reinstall the high-mount brake

light assembly on the rear shelf. Make sure the tabs on the high- mount brake light assembly fit into the slots.

Maintenance

Main MenuTable of ContentsstLights

Replacing a Rear License Bulb

4. Turn on the parking lights and

check that the new bulb is working.

5. Put the license light assembly in

place. Reinstall the two screws and tighten them securely.

1. Use a Phillips-head screwdriver to

remove the two screws holding the license plate light assembly to the bracket. Pull the assembly away from the bracket.

2. Remove the socket from the light

assembly by turning it one-quarter turn counterclockwise.

3. Pull the bulb straight out of its

socket. Push the new bulb in until it bottoms in the socket.

Maintenance

Main MenuTable of ContentsstReplacing Bulbs in the Interior Courtesy Lights The courtesy lights in the doors and roof come apart the same way. They do not all use the same bulb. The spotlight bulbs are in the ceiling light housing.

1. Remove the lens by carefully

prying on the edge of the lens with a fingernail file or a small flat-tip screwdriver. Do not pry on the edge of the housing around the lens.

Ceiling light:

Pry on the front edge of the lens in the middle.

On Type SH

Door light:

Pry on the top middle of the lens.

CEILING LIGHT

DOOR LIGHT

Lights

2. Remove the bulb by pulling it straight out of its metal tabs.

3. Push the new bulb into the metal tabs. Snap the lens back in place.

Maintenance

Main MenuTable of ContentsstLights

Replacing the Trunk Light Bulb

TRUNK LIGHT

1. Open the trunk. Pull down the

trunk light cover.

2. Remove the bulb by pulling it straight out of its metal tabs.

3. Push the new bulb into the metal

tabs.

4. Push the cover back in place.

Maintenance

Main MenuTable of ContentsstIf you need to park your car for an extended period (more than one month), there are several things you should do to prepare it for storage. Proper preparation helps prevent deterioration and makes it easier to get your car back on the road. If possible, store your car indoors.

Fill the fuel tank.

Change the engine oil and filter (see page 183 ).

Wash and dry the exterior completely.

Clean the interior. Make sure the carpeting, floor mats, etc. are completely dry.

Leave the parking brake off. Put the transmission in Reverse (5- speed manual) or Park (automatic).

Storing Your Car

Block the rear wheels.

If the car is to be stored for a longer period, it should be supported on jackstands so the tires are off the ground.

Leave one window open slightly (if the car is being stored indoors).

Disconnect the battery.

Support the front wiper blade arms with a folded towel or rag so they do not touch the windshield.

To minimize sticking, apply a silicone spray lubricant to all door and trunk seals. Also, apply a vehicle body wax to the painted surfaces that mate with the door and trunk seals.

Cover the car with a "breathable" cover, one made from a porous material such as cotton. Nonporous materials, such as plastic sheeting, trap moisture, which can damage the paint.

If possible, run the engine for a while periodically (preferably once a month).

If you store your car for 12 months or longer, have your Honda dealer perform the inspections called for in the 24 months/30,000 miles (48,000
km) maintenance schedule (Normal Conditions) as soon as you take it out of storage (see page 172). The replacements called for in the maintenance schedule are not needed unless the car has actually reached that time or mileage.

Maintenance

Main MenuTable of ContentsstAppearance Care

Regular cleaning and polishing of your Honda helps to keep it "new" looking. This section gives you hints on how to clean your car and preserve its appearance: the paint, brightwork, wheels and interior. Also included are several things you can do to help prevent corrosion.

Exterior Care.................................. 228
Washing...................................... 228
Waxing........................................229
Aluminum Wheels..................... 229
Paint Touch-up........................... 229
Interior Care................................... 230
Carpeting.................................... 230
Fabric.......................................... 230
Vinyl............................................ 230
Seat Belts....................................231
Windows.....................................231
Air Fresheners........................... 232
Corrosion Protection..................... 232
Body Repairs.................................. 233

Appearance Care

Main MenustExterior Care

Washing Frequent washing helps preserve your car's beauty. Dirt and grit can scratch the paint, while tree sap and bird droppings can permanently ruin the finish.

Wash your car in a shady area, not in direct sunlight. If the car is parked in the sun, move it into the shade and let the exterior cool down before you start.

Only use the solvents and cleaners recommended in this Owner's Manual.

NOTICE

Chemical solvents and strong cleaners can damage the paint, metal, and plastic on your car.

Appearance Care

When you have washed and rinsed the whole exterior, dry it with a chamois or soft towel. Letting it air-dry will cause dulling and water spots.

As you dry the car, inspect it for chips and scratches that could allow corrosion to start. Repair them with touch-up paint (see page 229).

Rinse the car thoroughly with cool water to remove loose dirt.

Fill a bucket with cool water. Mix in a mild detergent, such as dishwashing liquid or a product made especially for car washing.

Wash the car using the water and detergent solution and a soft- bristle brush, sponge, or soft cloth. Start at the top and work your way down. Rinse frequently.

Check the body for road tar, tree sap, etc. Remove these stains with tar remover or turpentine. Rinse it off immediately so it does not harm the finish. Remember to re- wax these areas, even if the rest of the car does not need waxing.

Main MenuTable of ContentsstWaxing Always wash and dry the whole car before waxing it. You should wax your car, including the metal trim, whenever water sits on the surface in large patches. It should form into beads or droplets after waxing.

You should use a quality liquid or paste wax. Apply it according to the instructions on the container. In general, there are two types of products:

Waxes — A wax coats the finish and protects it from damage by exposure to sunlight, air pollution, etc. You should use a wax on your Honda when it is new.

Polishes — Polishes and cleaner/ waxes can restore the shine to paint that has oxidized and lost some of its shine. They normally contain mild abrasives and solvents that remove the top layer of the finish. You

should use a polish on your Honda if the finish does not have its original shine after using a wax.

Cleaning tar, insects, etc. with removers also takes off the wax. Remember to re-wax those areas, even if the rest of the car does not need waxing.

Aluminum Wheels Clean your Honda's aluminum alloy wheels as you do the rest of the exterior. Wash them with the same solution, and rinse them thoroughly.

The wheels have a protective clear- coat that keeps the aluminum from corroding and tarnishing. Using harsh chemicals, including some commercial wheel cleaners, or stiff brushes can damage this clear-coat. Only use a mild detergent and soft brush or sponge to clean the wheels.

Exterior Care

Paint Touch-up Your dealer has touch-up paint to match your car's color. The color code is printed on a sticker on the driver's doorjamb. Take this code to your dealer so you are sure to get the correct color.

Inspect your car frequently for chips or scratches in the paint. Repair them right away to prevent corrosion of the metal underneath. Use the touch-up paint only on small chips and scratches. More extensive paint damage should be repaired by a professional.

Appearance Care

Main MenuTable of ContentsstInterior Care

Carpeting Vacuum the carpeting frequently to remove dirt. Ground-in dirt will make the carpet wear out faster. Periodically shampoo the carpet to keep it looking new. Use one of the foam-type carpet cleaners on the market. Follow the instructions that come with the cleaner, applying it with a sponge or soft brush. Keep the carpeting as dry as possible by not adding water to the foam.

Fabric Vacuum dirt and dust out of the material frequently. For general cleaning, use a solution of mild soap and lukewarm water, letting it air dry. To clean off stubborn spots, use a commercially-available fabric cleaner. Test it on a hidden area of the fabric first, to make sure it does not bleach or stain the fabric. Follow the instructions that come with the cleaner.

Vinyl Remove dirt and dust with a vacuum cleaner. Wipe the vinyl with a soft cloth dampened in a solution of mild soap and water. Use the same solution with a soft-bristle brush on more difficult spots. You can also use commercially-available spray or foam-type vinyl cleaners.

Appearance Care

Main MenuTable of ContentsstSeat Belts

LOOP

Dirt build-up in the loops of the seat belt anchors can cause the belts to retract slowly. Wipe the insides of the loops with a clean cloth dampened in mild soap and warm water or isopropyl alcohol.

If your seat belts get dirty, you can use a soft brush with a mixture of mild soap and warm water to clean them. Do not use bleach, dye, or cleaning solvents. They can weaken the belt material. Let the belts air- dry before you use the car.

Interior Care

Windows Clean the windows, inside and out, with a commercially-available glass cleaner. You can also use a mixture of one part white vinegar to ten parts water. This will remove the haze that builds up on the inside of the windows. Use a soft cloth or paper towels to clean all glass and clear plastic surfaces.

NOTICE

The rear window defogger and antenna wires are bonded to the inside of the glass. Wiping vigorously up-and- down can dislodge and break these wires. When cleaning the rear window, use gentle pressure and wipe side-to- side.

Appearance Care

Main MenuTable of ContentsstInterior Care, Corrosion Protection

Air Fresheners If you want to use an air freshener/ deodorizer in the interior of your car, it is best to use a solid type. Some liquid air fresheners contain chemi- cals that may cause parts of the interior trim and fabric to crack or discolor.

If you use a liquid air freshener, make sure you fasten it securely so it does not spill as you drive.

Corrosion Protection Two factors normally contribute to causing corrosion in your car:

Inspect and clean out the drain holes in the bottom of the doors and body.

1. Moisture trapped in body cavities. Dirt and road salt that collects in hollows on the underside of the car stays damp, promoting corrosion in that area.

2. Removal of paint and protective coatings from the exterior and underside of the car.

Many corrosion-preventive measures are built into your Honda. You can help keep your car from corroding by performing some simple periodic maintenance:

Repair chips and scratches in the paint as soon as you discover them.

Check the floor coverings for dampness. Carpeting and floor mats may remain damp for a long- time, especially in winter. This dampness can eventually cause the floor panels to corrode.

Use a high-pressure spray to clean the underside of your car. This is especially important in areas that use road salt in winter. It is also a good idea in humid climates and areas subject to salt air. Be careful of the ABS wheel sensors and wiring at each wheel.

Have the corrosion-preventive coatings on the underside of your car inspected and repaired periodically.

Appearance Care

Main MenuTable of ContentsstBody repairs can affect your car's resistance to corrosion. If your car needs repairs after a collision, pay close attention to the parts used in the repair and the quality of the work.

Make sure the repair facility uses Genuine Honda replacement body parts. Some companies make sheet metal pieces that seem to duplicate the original Honda body parts, but are actually inferior in fit, finish, and corrosion resistance. Once installed, they do not give the same high- quality appearance.

When reporting your collision to the insurance company, tell them you want Genuine Honda parts used in the repair. Although most insurers recognize the quality of original parts, some may try to specify that the repairs be done with other available parts. You should investi- gate this before any repairs have begun.

Take your car to your authorized Honda dealer for inspection after the repairs are completed. Your dealer can make sure that quality materials were used, and that corrosion- preventive coatings were applied to all repaired and replaced parts.

Body Repairs

Appearance Care

Main MenuTable of ContentsstTaking Care of the Unexpected

This section covers the more- common problems that motorists experience with their vehicles. It gives you information about how to safely evaluate the problem and what to do to correct it. If the problem has stranded you on the side of the road, you may be able to get going again. If not, you will also find instructions on getting your car towed.

Compact Spare Tire....................... 236
Changing a Flat Tire ..................... 237
If Your Engine Won't Start........... 242

Nothing Happens or the Starter Motor Operates Very Slowly............................. 243

The Starter Operates

Normally................................. 244
Jump Starting................................. 244
If Your Engine Overheats............. 246
Low Oil Pressure Indicator.......... 248
Charging System Indicator........... 249
Malfunction Indicator Lamp ........ 250
Brake System Indicator................ 251
Closing the Moonroof................... 252
Fuses...............................................253
Checking and Replacing........... 254
Emergency Towing....................... 258

Taking Care of the Unexpected

Main MenustCompact Spare Tire

Your car has a compact spare tire that takes up less space. Use this spare tire as a temporary replace- ment only. Get your regular tire repaired or replaced and put back on your car as soon as you can.

Check the inflation pressure of the compact spare tire every time you check the other tires. It should be inflated to: 60 psi (420 kPa , 4.2 kgf/cm 2)

Taking Care of the Unexpected

Follow these precautions whenever you are using the compact spare tire:

INDICATOR LOCATION MARK

Do not exceed 50 mph (80 km/h) under any circumstances.

This tire gives a harsher ride and less traction on some road sur- faces than the regular tire. Use greater caution while driving on this tire.

Do not mount snow chains on the compact spare.

The wheel of the compact spare tire is designed especially to fit your car. Do not use your spare tire on another vehicle unless it is the same make and model.

TREAD WEAR INDICATOR BAR

The compact spare tire has a shorter tread life than a regular tire. Replace it when you can see the tread wear indicator bars. The replacement should be the same size and design tire, mounted on the same wheel. The compact spare tire is not designed to be mounted on a regular wheel, and the compact wheel is not designed for mounting a regular tire.

Main MenuTable of ContentsstIf you have a flat tire while driving, stop in a safe place to change it. Stopping in traffic or on the shoulder of a busy road is dangerous. Drive slowly along the shoulder until you get to an exit or an area to stop that is far away from the traffic lanes.

The car can easily roll off the jack, seriously injuring anyone underneath.

Follow the directions for changing a tire exactly, and never get under the car when it is supported only by the jack.

Changing a Flat Tire

JACK

TRUNK FLOOR

3. Open the trunk. Raise the trunk

floor by lifting up on the back edge.

4. Take the tool kit out of the trunk.

5. Unscrew the wing bolt and take

the spare tire out of its well.

TOOL KIT

SPARE TIRE

1. Park the car on firm, level and

non-slippery ground away from traffic. Put the transmission in Park (automatic) or Reverse (manual). Apply the parking brake.

2. Turn on the hazard warning lights

and turn the ignition switch to LOCK (0). Have all the passengers get out of the car while you change the tire.

CONTINUED

Taking Care of the Unexpected

Main MenuTable of ContentsstChanging a Flat Tire

JACK

HANDLE

COVER

6. The jack is behind a cover in the left fender. Remove the cover by turning the handle clockwise, then pulling on the cover.

7. Turn the jack's end bracket

counterclockwise to loosen it, then remove the jack.

WHEEL WRENCH

8. Loosen the five wheel nuts 1/2

turn with the wheel wrench.

Taking Care of the Unexpected

Main MenuTable of ContentsstChanging a Flat Tire

JACKING POINT

WHEEL WRENCH

EXTENSION

9. Locate the jacking point nearest the tire you need to change. It is pointed to by a mark molded into the underside of the body. Place the jack under the jacking point. Turn the end bracket clockwise until the top of the jack contacts the jacking point. Make sure the jacking point tab is resting in the jack notch.

10. Use the extension and wheel wrench as shown to raise the vehicle until the flat tire is off the ground.

11. Remove the wheel nuts and flat

tire. Temporarily place the flat tire on the ground with the outside surface of the wheel facing up. You could scratch the wheel if you put it face down.

CONTINUED

Taking Care of the Unexpected

Main MenuTable of ContentsstChanging a Flat Tire

BRAKE HUB

12. Before mounting the spare tire, wipe any dirt off the mounting surface of the wheel and hub with a clean cloth. Wipe the hub carefully, it may be hot from driving.

13. Put on the spare tire. Put the

wheel nuts back on finger-tight, then tighten them in a crisscross pattern with the wheel wrench until the wheel is firmly against the hub. Do not try to tighten them fully.

14. Lower the car to the ground and

remove the jack.

Taking Care of the Unexpected

Main MenuTable of ContentsstChanging a Flat Tire

WING BOLT

SPACER CONE

15. Tighten the wheel nuts securely in the same crisscross pattern. Have the wheel nut torque checked at the nearest automotive service facility. Tighten the wheel nuts to: 80 lbf.ft (108 N.m, 11 kgf.m)

CENTER CAP

16. Remove the center cap before storing the flat tire in the trunk well.

17. Place the flat tire face down in the

spare tire well.

18. Remove the spacer cone from the

wing bolt, turn it over, and put it back on the bolt.

CONTINUED

Taking Care of the Unexpected

Main MenuTable of ContentsstChanging a Flat Tire, If Your Engine Won't Start

19. Secure the flat tire by screwing the wing bolt back into its hole.

20. Store the jack in its holder. Turn

the jack's end bracket to lock it in place. Replace the cover. Store the tool kit.

Loose items can fly around the interior in a crash and could seriously injure the occupants.

Store the wheel, jack and tools securely before driving.

21. Store the center cap in the trunk.

Make sure it does not get scratch- ed or damaged.

22. Lower the trunk floor, then close

the trunk lid.

Type SH only If you mount the compact spare on either front or rear tire, it may cause the ATTS indicator light in the instrument panel to come on due to the difference in tire diameter. The light will go out when the proper tire is installed.

If Your Engine Won't Start Diagnosing why your engine won't start falls into two areas, depending on what you hear when you turn the key to START (III):

You hear nothing, or almost nothing. The engine's starter motor does not operate at all, or operates very slowly.

You can hear the starter motor operating normally, or the starter motor sounds like it is spinning faster than normal, but the engine does not start up and run.

Taking Care of the Unexpected

Main MenuTable of ContentsstNothing Happens or the Starter Motor Operates Very Slowly When you turn the ignition switch to START (III), you do not hear the normal noise of the engine trying to start. You may hear a clicking sound or series of clicks, or nothing at all. Check these things:

Your car has the Immobilizer System. You should use a properly-coded master or valet key to start the engine (see page 71). A key that is not properly coded will cause the immobilizer system indicator in the dash panel to blink rapidly.

Check the transmission interlock. If you have a manual transmission, the clutch pedal must be pushed all the way to the floor or the starter will not operate. With an automatic transmission, it must be in Park or Neutral.

Turn the ignition switch to ON (II). Turn on the headlights and check their brightness. If the headlights are very dim or don't light at all, the battery is discharged. See Jump Starting on page 244 .

Turn the ignition switch to START (III). If the headlights do not dim, check the condition of the fuses. If the fuses are OK, there is proba- bly something wrong with the electrical circuit for the ignition switch or starter motor. You will need a qualified technician to determine the problem. (See Emergency Towing on page 258.)

If Your Engine Won't Start

If the headlights dim noticeably or go out when you try to start the engine, either the battery is dis- charged or the connections are corroded. Check the condition of the battery and terminal connections (see page 198). You can then try jump starting the car from a booster battery (see page 244).

Taking Care of the Unexpected

Main MenuTable of ContentsstIf Your Engine Won't Start, Jump Starting

The Starter Operates Normally In this case, the starter motor's speed sounds normal, or even faster than normal, when yon turn the ignition switch to START (III), but the engine does not run.

Are you using the proper starting procedure? Refer to Starting the Engine on page 141.

Do you have fuel? Turn the ignition switch to ON (II) for a minute and watch the fuel gauge. The low fuel level warning light may not be working, so you were not reminded to fill the tank.

There may be an electrical problem, such as no power to the fuel pump. Check all the fuses (see page 254).

If you find nothing wrong, you will need a qualified technician to find the problem. See Emergency Towing on page 258 .

Taking Care of the Unexpected

Jump Starting If your car's battery has run down, you may be able to start the engine by using a booster battery. Although this seems like a simple procedure, you should take several precautions.

A battery can explode if you do not follow the correct procedure, seriously injuring anyone nearby.

Keep all sparks, open flames, and smoking materials away from the battery.

You cannot start a Honda with an automatic transmission by pushing or pulling it.

To jump start your car, follow these directions closely:

1. Open the hood and check the

physical condition of the battery (see page 198). In very cold weather, check the condition of the electrolyte. If it seems slushy or like ice, do not try jump starting until it thaws.

NOTICE

If a battery sits in extreme cold, the electrolyte inside can freeze. Attempting to jump start with a frozen battery can cause it to rupture.

2. Turn off all the electrical acces-

sories: heater, A/C, stereo system, lights, etc.

Put the transmission in Neutral or Park and set the parking brake.

Main MenuTable of ContentsstJump Starting

3. Connect one jumper cable to the

positive ( + ) terminal on the booster battery. Connect the other end to the positive ( + ) terminal on your Honda's battery.

4. Connect the second jumper cable

to the negative ( — ) terminal on the booster battery. Connect the other end to the grounding strap as shown. Do not connect this jumper cable to any other part of the engine.

5. If the booster battery is in another

vehicle, have an assistant start that vehicle and run it at a fast idle.

BOOSTER BATTERY

6. Start your car. If the starter motor

still operates slowly, check the jumper cable connections to make sure they have good metal-to- metal contact.

7. Once your car is running, discon- nect the negative cable from your car, then from the booster battery. Disconnect the positive cable from your car, then the booster battery.

Taking Care of the Unexpected

Main MenuTable of ContentsstIf Your Engine Overheats

The pointer of your car's tempera- ture gauge should stay in the mid- range under most conditions. It may go higher if you are driving up a long steep hill on a very hot day. If it climbs to the red mark, you should determine the reason.

NOTICE

Driving with the temperature gauge pointer at the red mark can cause serious damage to your engine.

Taking Care of the Unexpected

Your car can overheat for several reasons, such as lack of coolant or a mechanical problem. The only indication may be the temperature gauge climbing to or above the red mark. Or you may see steam or spray coming from under the hood. In either case, you should take immediate action.

Steam and spray from an overheated engine can seriously scald you.

2. If you see steam and/or spray

coming from under the hood, turn off the engine.

3. If you do not see steam or spray,

leave the engine running and watch the temperature gauge. If the high heat is due to overloading (climbing a long, steep hill on a hot clay with the A/C running, for example), the engine should start to cool down almost immediately. If it does, wait until the tempera- ture gauge comes down to the mid- point then continue driving.

Do not open the hood if steam is coming out.

4. If the temperature gauge stays at the red mark, turn off the engine.

1. Safely pull to the side of the road. Put the transmission in Neutral or Park and set the parking brake. Turn off the heating and cooling system and all other accessories. Turn on the hazard warning indicators.

5. Wait until you see no more signs of steam or spray, then open the hood.

Main MenuTable of Contentsst6. Look for any obvious coolant leaks,

such as a split radiator hose. Everything is still extremely hot, so use caution. If you find a leak, it must be repaired before you continue driving (see Emergency Towing on page 258).

7. If you don't find an obvious leak,

check the coolant level in the radiator reserve tank (see page 131). If the level is below the MIN mark, add coolant to halfway between the MIN and MAX marks.

8. If there was no coolant in the

reserve tank, you may also have to add coolant to the radiator. Let the engine cool down until the pointer reaches the middle of the tempera- ture gauge, or lower, before check- ing the radiator.

Removing the radiator cap while the engine is hot can cause the coolant to spray out, seriously scalding you.

Always let the engine and radiator cool down before removing the radiator cap.

9. Using gloves or a large heavy

cloth, turn the radiator cap counterclockwise, without pushing down, to the first stop. This releases any remaining pressure in the cooling system. After the pressure releases, push down on the cap and turn it until it comes off.

If Your Engine Overheats

10. Start the engine and set the temperature control lever to maximum. Add coolant to the radiator up to the base of the filler neck. If you do not have the proper coolant mixture available, you can add plain water. Remember to have the cooling system drained and refilled with the proper mixture as soon as you can.

11. Put the radiator cap back on

tightly. Run the engine and watch the temperature gauge. If it goes back to the red mark, the engine needs repair. (See Emergency Towing on page 258.)

12. If the temperature stays normal,

check the coolant level in the radiator reserve tank. If it has gone down, add coolant to the MAX mark. Put the cap back on tightly.

Taking Care of the Unexpected

Main MenuTable of Contentsst4. Start the engine and watch the oil

pressure indicator. If the light does not go out within ten seconds, turn off the engine. There is a mechanical problem that needs to be repaired before you can continue driving. (See Emergency Towing on page 258.)

Low Oil Pressure Indicator

LOW OIL PRESSURE INDICATOR

This indicator should light when the ignition switch is ON (II), and go out after the engine starts. It should never come on when the engine is running. If it starts flashing, it indicates that the oil pressure dropped very low for a moment, then recovered. If the indicator stays on with the engine running, it shows that the engine has lost oil pressure and serious engine damage is possible. In either case, you should take immediate action.

Taking Care of the Unexpected

NOTICE

Running the engine with low oil pressure can cause serious mechanical damage almost immediately. Turn off the engine as soon as yon can safely get the car stopped.

1. Safely pull off the road and shut

off the engine. Turn on the hazard warning indicators.

2. Let the car sit for a minute. Open

the hood and check the oil level (see page 130). Although oil level and oil pressure are not directly connected, an engine that is very low on oil can lose pressure during cornering and other driving maneuvers.

3. If necessary, add oil to bring the level back to the full mark on the dipstick (see page 181).

Main MenuTable of ContentsstCharging System Indicator

By eliminating as much of the electrical load as possible, you can drive several miles (kilometers) before the battery is too discharged to keep the engine running. Drive to a service station or garage where you can get technical assistance.

Immediately turn off all electrical accessories: radio, heater, A/C, rear clefogger, cruise control, etc. Try not to use other electrically-operated controls such as the power windows. Keep the engine running and take extra care not to stall it. Starting the engine will discharge the battery rapidly.

Taking Care of the Unexpected

CHARGING SYSTEM INDICATOR

This indicator should come on when the ignition switch is ON (II), and go out after the engine starts. If it comes on brightly when the engine is running, it indicates that the charging system has stopped charging the battery.

Main MenuTable of ContentsstNOTICE

If you keep driving with the malfunction indicator lamp on, you can damage your car's emissions controls and engine. Those repairs may not be covered by your car's warranties.

Malfunction Indicator Lamp

MALFUNCTION INDICATOR LAMP

This indicator comes on for a few seconds when you turn the ignition switch ON (II). If it comes on at any other time, it indicates one of the engine's emissions control systems may have a problem. Even though you may feel no difference in your car's performance, it can reduce your fuel economy and cause your car to put out excessive emissions. Continued operation may cause serious damage.

Taking Care of the Unexpected

If you have recently refueled your car, the cause of this indicator coming on could be a loose or missing fuel fill cap. Check the cap and tighten it until it clicks several times. Replace the fuel fill cap if it is missing. Tightening the cap will not make the indicator turn off immediately; it takes three driving trips.

If the indicator remains on past three driving trips, or the fuel cap was not loose or missing, have the car checked by the dealer as soon as possible. Drive moderately until the dealer has inspected the problem. Avoid full-throttle acceleration and driving at high speed.

You should also have the dealer inspect your car if this indicator comes on repeatedly, even though it may turn off as you continue driving.

Main MenuTable of ContentsstBRAKE SYSTEM INDICATOR

The Brake System indicator light comes on when you turn the ignition ON (II). If the parking brake is not set, it goes off after you start the engine. If the parking brake is set, it goes off when you fully release the parking brake with the engine running.

If it comes on at any other time, it indicates a problem with the car's brake system. In most cases, the problem is a low fluid level in the

brake fluid reservoir. Press lightly on the brake pedal to see if it feels normal. If it does, check the brake fluid level the next time you stop at a service station (see page 193 ). If the fluid level is low, take the car to your dealer and have the brake system inspected for leaks or worn brake pads.

However, if the brake pedal does not feel normal, you should take immediate action. Because of the brake system's dual-circuit design, a problem in one part of the system will still give you braking at two wheels. You will feel the brake pedal go down much farther before the car begins to slow down, and you will have to press harder on the pedal. The distance needed to stop will be much longer.

Slow down by shifting to a lower gear, and pull to the side of the road when it is safe. Because of the

Brake System Indicator

longer distance needed to stop, it is hazardous to drive the car. You should have it towed, and repaired as soon as possible. (See Emergency Towing on page 258.) If you must drive the car a short distance in this condition, drive slowly and cautiously.

Taking Care of the Unexpected

Main MenuTable of ContentsstClosing the Moonroof

If the electric motor will not close the moonroof, do the following:

1. Check the fuse for the moonroof motor (see page 254). If the fuse is blown, replace it with one of the same or lower rating.

2. Try closing the moonroof. If the

new fuse blows immediately or the moonroof motor still does not operate, you can close the moonroof manually.

3. Get the sunroof wrench out of the

tool kit in the trunk.

Taking Care of the Unexpected

SOCKET

ROUND PLUG

4. Use a screwdriver or coin to remove the round plug in the center of the headliner.

5. Insert the moonroof wrench into the socket behind this plug. Turn the wrench until the moonroof is fully closed.

6. Remove the wrench. Replace the

round plug.

Main MenuTable of ContentsstAll the electrical circuits in your car have fuses to protect them from a short circuit or overload. These fuses are located in two fuse boxes.

UNDER-HOOD

TAB

INTERIOR

Fuses

KNOB

The under-hood fuse box is located in the back of the engine compart- ment on the passenger's side. To open it, push the tab as shown.

The interior fuse box is underneath the dashboard on the driver's side. To open it, turn the knob as shown.

Taking Care of the Unexpected

Main MenuTable of ContentsstFuses

Checking and Replacing Fuses If something electrical in your car stops working, the first thing you should check for is a blown fuse. Determine from the chart on pages 256 and 257 , or the diagram on the fuse box lid, which fuse or fuses control that component. Check those fuses first, but check all the fuses before deciding that a blown fuse is not the cause. Replace any blown fuses and check the component's operation.

1. Turn the ignition switch to LOCK (0). Make sure the headlights and all other accessories are off.

2. Remove the cover from the fuse

box.

Taking Care of the Unexpected

FUSE

FUSE PULLER

BLOWN

3. Check each of the large fuses in

the under-hood fuse box by looking through the top at the wire inside. Removing these fuses requires a Phillips-head screw- driver.

4. Check the smaller fuses in the

under-hood fuse box and all the fuses in the interior fuse box by pulling out each fuse with the fuse puller provided in the interior fuse box.

Main MenuTable of ContentsstBLOWN

5. Look for a burned wire inside the fuse. If it is burned, replace it with one of the spare fuses of the same rating or lower.

If you cannot drive the car without fixing the problem, and you do not have a spare fuse, take a fuse of the same rating or a lower rating from one of the other circuits. Make sure you can do without that circuit temporarily (such as the accessory power socket or radio).

If you replace the blown fuse with a spare fuse that has a lower rating, it might blow out again. This does not indicate anything wrong. Replace the fuse with one of the correct rating as soon as you can.

Fuses

NOTICE

Replacing a fuse with one that has a higher rating greatly increases the chances of damaging the electrical system. If you do not have a replace- ment fuse with the proper rating for the circuit, install one with a lower rating.

6. If the replacement fuse of the

same rating blows in a short time, there is probably a serious electrical problem in your car. Leave the blown fuse in that circuit and have your car checked by a qualified mechanic.

If the radio fuse is removed, the audio system will disable itself. The next time you turn on the radio you will see in the frequency display. Use the Preset buttons to enter the five-digit code (see page 123).

CONTINUED

Taking Care of the Unexpected

Main MenuTable of ContentsstFuses

INTERIOR FUSE BOX

* 1 : On Type SH * 2 : On Canadian models

Taking Care of the Unexpected

Main MenuTable of ContentsstUNDER-HOOD FUSE BOX

Fuses

Taking Care of the Unexpected

Main MenuTable of ContentsstEmergency Towing

If your car needs to be towed, call a professional towing service or, if you belong to one, an organization that provides roadside assistance. Never tow your car behind another vehicle with just a rope or chain. It is very dangerous.

There are three popular methods of towing a vehicle:

Flat-bed Equipment — The operator loads your car on the back of a truck. This is the best way to transport your Honda.

Wheel-Lift Equipment — The tow truck uses two pivoting arms that go under the tires (front or rear) and lift them off the ground. The other two tires remain on the ground. This is an acceptable way to tow your Honda.

Taking Care of the Unexpected

Sling-type Equipment — The tow truck uses metal cables with hooks on the ends. These hooks go around parts of the frame or suspension and the cables lift that end of the car off the ground. Your car's suspension and body can be seriously damaged. This method of towing is unacceptable.

If your Honda cannot be transported by flat-bed, it should be towed by wheel-lift equipment with the front wheels off the ground. If, due to damage, your car must be towed with the front wheels on the ground, do the following:

5-speed Manual Transmission

Release the parking brake. Shift the transmission to Neutral.

Automatic Transmission:

Release the parking brake. Start the engine. Shift to D4, then to N. Turn off the engine.

NOTICE

Improper towing preparation will damage the transmission. Follow the above procedure exactly If you cannot shift the transmission or start the engine (automatic transmission), your car must be transported with the front wheels off the ground.

With the front wheels on the ground, it is best to tow the car no farther than 50 miles (80 km), and keep the speed below 35 mph (55 km/h).

Main MenuTable of ContentsstNOTICE

Trying to lift or tow your car by the bumpers will cause serious damage. The bumpers are not designed to support the car's weight.

If you decide to tow your car with all four wheels on the ground, make sure you use a properly-designed and attached tow bar. Prepare the car for towing as described above, and leave the ignition switch in Accessory (I) so the steering wheel docs not lock. Make sure the radio and any items plugged into the accessory power socket are turned off so they do not run down the battery.

NOTICE

The steering system can he damaged if the steering wheel is locked. Leave the ignition switch in Accessory (I), and make sure the steering wheel turns freely before you begin towing.

Emergency Towing

Taking Care of the Unexpected

Main MenuTable of ContentsstThe diagrams in this section give you the dimensions and capacities of your Honda, and the locations of the identification numbers. The expla- nations of several electronic and mechanical systems on your Honda are for the more technically-oriented owner.

Technical Information

Identification Numbers................. 262
Specifications................................. 264
DOT Tire Quality Grading........... 266
Treadwear.................................. 266
Traction....................................... 266
Temperature.............................. 267

Oxygenated Fuels.......................... 268
Driving in Foreign Countries....... 269
Emissions Controls........................ 270
The Clean Air Act...................... 270
Crankcase Emissions Control

System..................................... 270

Evaporative Emissions Control

System.....................................270
Exhaust Emissions Controls.... 271
PGM-FI System..................... 271
Ignition Timing Control

System.................................271

Exhaust Gas Recirculation

(EGR) System.................... 271

Three Way Catalytic

Converter............................ 271
Replacement Parts..................... 271
Three Way Catalytic Converter... 272

Technical Information

Main MenustIdentification Numbers

Your car has several identifying numbers located in various places.

The Vehicle Identification Number (VIN) is the 17-digit number your Honda dealer uses to register your car for warranty purposes. It is also necessary for licensing and insuring your car. The easiest place to find the VIN is on a plate fastened to the top of the dashboard. You can see it by looking through the windshield on the driver's side. It is also on the Certification label attached to the driver's doorjamb, and is stamped on the engine compartment bulkhead. The VIN is also provided in bar code on the Certification label.

Technical Information

VEHICLE IDENTIFICATION NUMBER

CERTIFICATION LABEL

Main MenuTable of ContentsstIdentification Numbers

MANUAL TRANSMISSION NUMBER

AUTOMATIC TRANSMISSION NUMBER

The Engine Number is stamped into the engine block.

The Transmission Number is on a label on top of the transmission.

ENGINE NUMBER

Technical Information

Main MenuTable of ContentsstSpecifications

page 198 .

Technical Information

* 1 : Including the coolant in the reserve tank and that remaining in the

engine. Reserve tank capacity: 0.16 US gal (0.6 l , 0.13 Imp gal)

* 2: Type SH *3 : Except Type SH *4 : Excluding the oil remaining in the engine.

Main MenuTable of ContentsstSpecifications

page 256

page 257

* 1 : Except high-mount brake light installed in rear spoiler * 2 : Type SH

* 1 : Except Type SH * 2 : Type SH

* 1 : Except Type SH * 2 : Type SH

Technical Information

Main MenuTable of ContentsstDOT Tire Quality Grading (U.S. Cars)

The tires on your car meet all U.S. Federal Safety Requirements. All tires are also graded for treadwear, traction, and temperature perform- ance according to Department of Transportation (DOT) standards. The following explains these gradings.

Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between the tread shoulder and the maximum section width. For example:

Treadwear 200
Traction AA Temperature A

Treadwear The treadwear grade is a compara- tive rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one half (1-1/2) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual condi- tions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices, and differences in road characteristics and climate.

Traction The traction grades, from highest to lowest, are AA, A, B, and C. Those grades represent the tire's ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance.

Warning: The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.

Technical Information

Main MenuTable of ContentsstDOT Tire Quality Grading (U.S. Cars)

Warning: The temperature grade for this tire is established for a tire that is properly inflated and not over- loaded. Excessive speed, underinfla- tion, or excessive loading either separately or in combination, can cause heat build-up and possible tire failure.

Temperature The temperature grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law.

Technical Information

Main MenuTable of ContentsstIf you notice any undesirable operating symptoms, try another service station or switch to another brand of gasoline.

Fuel system damage or performance problems resulting from the use of an oxygenated fuel containing more than the percentages of oxygenates given above are not covered under warranty.

Oxygenated Fuels

Some conventional gasolines are being blended with alcohol or an ether compound. These gasolines are collectively referred to as oxygenated fuels. To meet clean air standards, some areas of the United States and Canada use oxygenated fuels to help reduce emissions.

If you use an oxygenated fuel, be sure it is unleaded and meets the minimum octane rating requirement.

Before using an oxygenated fuel, try to confirm the fuel's contents. Some states/provinces require this information to be posted on the pump.

Technical Information

The following are the U.S. EPA and Canadian CGSB approved percentages of oxygenates:

ETHANOL (ethyl or grain alcohol) You may use gasoline containing up to 10 percent ethanol by volume. Gasoline containing ethanol may be marketed under the name "Gasohol."

MTBE (Methyl Tertiary Butyl Ether) You may use gasoline containing up to 15 percent MTBE by volume.

METHANOL (methyl or wood alcohol) Your vehicle was not designed to use fuel that contains methanol. Methanol can corrode metal parts in the fuel system, and also damage plastic and rubber components. This damage would not be covered by your warranties.

Main MenuTable of ContentsstIf you are planning to take your Honda outside the U.S. or Canada, contact the tourist bureaus in the areas you will be traveling in to find out about the availability of unleaded gasoline with the proper octane rating.

If unleaded gasoline is not available, be aware that using leaded gasoline in your Honda will affect perfor- mance and fuel mileage, and damage its emissions controls. It will no longer comply with U.S. and Canadian emissions regulations, and will be illegal to operate in North America. To bring your car back into compliance will require the replace- ment of several components, such as the oxygen sensors and the three way catalytic converter. These re- placements are not covered under warranty.

Driving in Foreign Countries

Technical Information

Main MenuTable of ContentsstEmissions Controls

The burning of gasoline in your car's engine produces several byproducts. Some of these are carbon monoxide (CO), oxides of nitrogen (NOx) and hydrocarbons (HC). Gasoline evaporating from the tank also produces hydrocarbons. Controlling the production of NOx, CO, and HC is important to the environment. Under certain conditions of sunlight and climate, NOx and HC react to form photochemical "smog." Carbon monoxide does not contribute to smog creation, but it is a poisonous gas.

Technical Information

The Clean Air Act The United States Clean Air Act* sets standards for automobile emissions. It also requires that automobile manufacturers explain to owners how their emissions controls work and what to do to maintain them. This section summarizes how the emissions controls work. Scheduled maintenance is on page 172.

* In Canada, Honda vehicles comply with the Canadian Motor Vehicle Safety Standards (CMVSS) for Emissions valid at the time they are manufactured.

Crankcase Emissions Control System Your car has a Positive Crankcase Ventilation System. This keeps gasses that build up in the engine's crankcase from going into the atmosphere. The Positive Crankcase Ventilation valve routes them from

the crankcase back to the intake manifold. They are then drawn into the engine and burned.

Evaporative Emissions Control System As gasoline evaporates in the fuel tank, an evaporative emissions control canister filled with charcoal adsorbs the vapor. It is stored in this canister while the engine is off. After the engine is started and warmed up, the vapor is drawn into the engine and burned during driving.

Onboard Refueling Vapor Recovery The Onboard Refueling Vapor Recovery (ORVR) system captures the fuel vapors during refueling. The vapors are adsorbed in a canister filled with activated carbon. While driving, the fuel vapors are drawn into the engine and burned off.

Main MenuTable of ContentsstExhaust Emissions Controls The exhaust emissions controls include four systems: PGM-FI, Ignition Timing Control, Exhaust Gas Recirculation and Three Way Catalytic Converter. These four systems work together to control the engine's combustion and minimize the amount of HC, CO, and NOx that comes out the tailpipe. The exhaust emissions control systems are separate from the crankcase and evaporative emissions control systems.

PGM-FI System The PGM-FI System uses sequential multiport fuel injection. It has three subsystems: Air Intake, Engine Control, and Fuel Control. The Engine Control Module (ECM) uses various sensors to determine how much air is going into the engine. It then controls how much fuel to inject under all operating conditions.

Ignition Timing Control System This system constantly adjusts the ignition timing, reducing the amount of HC, CO and NOx produced.

Exhaust Gas Recirculation (EGR) System The Exhaust Gas Recirculation (EGR) system takes some of the exhaust gas and routes it back into the intake manifold. Adding exhaust gas to the air/fuel mixture reduces the amount of NOx produced when the fuel is burned.

Three Way Catalytic Converter The three way catalytic converter is in the exhaust system. Through chemical reactions, it converts HC, CO, and NOx in the engine's exhaust to carbon dioxide (CO2), dinitrogen (N2), and water vapor.

Emissions Controls

Replacement Parts The emissions control systems are designed and certified to work to- gether in reducing emissions to levels that comply with the Clean Air Act. To make sure the emissions remain low, you should use only new Genuine Honda replacement parts or their equivalent for repairs. Using lower quality parts may increase the emissions from your car.

The emissions control systems are covered by warranties separate from the rest of your car. Read your warranty manual for more informa- tion.

Technical Information

Main MenuTable of ContentsstKeep the engine tuned-up.

Have your car diagnosed and repaired if it is misfiring, back- firing, stalling, or otherwise not running properly.

Three Way Catalytic Converter

The three way catalytic converter contains precious metals that serve as catalysts, promoting chemical reactions to convert the exhaust gasses without affecting the metals. The catalytic converter is referred to as a three-way catalyst, since it acts on HC, CO, and NOx. A replacement unit must be an original Honda part or its equivalent.

The three way catalytic converter must operate at a high temperature for the chemical reactions to take place. It can set on fire any com- bustible materials that come near it. Park your car away from high grass, dry leaves, or other flammables.

Technical Information

THREE WAY CATALYTIC CONVERTER

A defective three way catalytic converter contributes to air pollution, and can impair your engine's per- formance. Follow these guidelines to protect your car's three way catalytic converter.

Always use unleaded gasoline. Even a small amount of leaded gasoline can contaminate the catalyst metals, making the three way catalytic converter ineffective.

Main MenuTable of ContentsstWarranty and Customer Relations

Customer Relations

Information................................. 274
U.S. Zone Office Map.................... 275
Canada Zone Office Map.............. 276
Warranty Coverages..................... 277
Reporting Safety Defects

(U.S. Vehicles)........................... 278
Authorized Manuals...................... 279

Warranty and Customer Relations

Main MenustCustomer Relations Information

Honda dealership personnel are trained professionals. They should be able to answer all your questions. If you encounter a problem that your dealership does not solve to your satisfaction, please discuss it with the dealership's management. The Service Manager or General Manager can help. Almost all problems are solved in this way.

If you are dissatisfied with the decision made by the dealership's management, contact your Honda Customer Relations Zone Office. Refer to the U.S. and Canadian Zone Office maps on the following pages.

When you call or write, please give us this information:

Vehicle Identification Number (see page 262) Name and address of the dealer who services your car Date of purchase Mileage on your car Your name, address, and tele- phone number A detailed description of the problem Name of the dealer who sold the car to you

Warranty and Customer Relations

Main MenuTable of ContentsstU.S. Zone Office Map

Western Zone P.O. Box 2260

700 Van Ness Avenue Torrance, California 90509-2260
(310) 781-4565

Northwestern Zone P.O. Box 20186

12439 N.E. Airport Way Portland, Oregon 97230
(503) 256-0943
(also includes Alaska and Hawaii)

South Central Zone 4529 Royal Lane

Irving, Texas 75063
(972) 929-5481

Central Zone 101 South Stanfield Road

Troy, Ohio 45373
(937) 332-6250

Mid-Atlantic Zone 902 Wind River Ln., Suite 200

Gaithersburg, Maryland 20878
(301) 990-2020

Southeastern Zone 1500 Morrison Parkway

Alpharetta, Georgia 30004
(770) 442-2045

North Central Zone 601 Campus Drive, Suite A-9

Arlington Heights, Illinois 60004
(847) 870-5600

New England Zone 555 Old County Road

Windsor Locks, Connecticut 06096
(860)623-3310
See Zone 5 for: NYC Metro area and Fairfield County, CT area

West Central Zone 1600 South Abilene Street, Suite D

Northeastern Zone P.O. Box 337

Aurora, Colorado 80012
(303) 696-3935

Eastgate Industrial Park 115 Gaither Drive Moorestown, New Jersey 08057
(609) 235-5533
Includes: NYC Metro area and Fairfield County, CT area

Puerto Rico and U.S. V.I. Bella International

P.O. Box 190816
San Juan, PR 00919-0816
(787) 250-4318

Warranty and Customer Relations

The addresses and telephone numbers are subject to change. If you cannot reach your Zone office, ask your Honda dealer for the current information.

Main MenuTable of ContentsstCanada Zone Office Map

CUSTOMER RELATIONS RELATIONS AVEC LA CLIENTELE

Honda Canada Inc. 715 Milner Avenue Toronto, ON M1B 2K8