Download PDF Manual

1. When starting in cold weather at high altitude (above 8,000 feet), push the accelerator pedal about halfway and hold it there while cranking the engine. Once the engine starts, release the accelerator gradually as the engine speeds up.


2. If ft doesn't start within 15 seconds, push the accelerator pedal down to the floor and hold it there while cranking in order to clear flooding. Try step 1 again.


NOTE: If the outside temperature is below freezing, or if your car has not been driven for several days, warm up the engine for a few minutes before driving.


Main Menust Safety Items


Before driving away, check that: The doors are closed properly. The mirrors are properly adjusted, and the windows clean. The driver and passengers are wearing properly adjusted seat belts. The head restraints are properly adjusted. The warning and indicator lights are operating properly. The brake pedal feels normal. All luggage and cargo is secured. Nothing is interfering with the driver's feet or blocking vision to the rear.


While driving remember to:


Always drive defensively; expect the unexpected. Reduce your speed during night hours and bad weather. Follow at a safe distance; don't tailgate. Get off the highway when you are tired; stop and take a rest.


When stopping for repairs:


Park the car well off the road. Turn on the hazard warning flasher. Use flares or other warning devices to warn other motorists.


After parking your car:


Apply the parking brake and shift to first gear if equipped with manual transmission, or PARK on automatic transmission equip- ped cars. Make sure the sunroof and windows are closed and the doors are locked. if parked on a hill: Turn the front wheels away from the curb if facing uphill. Turn the front wheels toward the curb if facing downhill. Never leave children unattended in a parked car. Take your keys.


Main Menust Engine Exhaust Gas Warning


A properly maintained car is your best protection against exhaust gas entering the passenger compartment. The exhaust system should be thoroughly inspected by a compe- tent mechanic whenever:


The car is raised for oil change. You notice a change in the sound of the exhaust. The exhaust system or the rear or underside of the car is damaged.


Avoid breathing exhaust gases. They contain carbon monoxide, which is a colorless, odorless gas that can cause loss of con- sciousness and eventual death. If you suspect that exhaust gas is entering the passenger compartment, have the cause deter- mined and corrected as soon as possible. If you must drive under these conditions, drive only with all windows fully open. Do not drive with the trunk lid open. An open trunk lid may draw exhaust gases into the passenger compartment. If you must drive with the trunk lid open, drive only with all the windows wide open. Do not run the engine in confined areas, such as garages, any longer than necessary to move the car in or out. If you must sit in a parked car with the engine running for more than a short time, adjust the heating/ventilation system as follows:


1. Push the 2. Set the temperature lever for best comfort. 3.Turn the fan to the highest speed.


buttons on.


and


NOTE: To insure proper operation of the car's ventilation system, keep the front air inlet clear of snow, mud, leaves or other obstructions.


Main Menust Shifting the 5 Speed


The fully synchronized manual transmission is very easy to shift up or down. When you slow down for traffic, steep hills, or corners, shift to a lower gear before the engine starts to labor. When de- scending steep grades, select a lower gear to help maintain a safe speed and to prevent the brakes from overheating. When shifting, depress the clutch pedal fully, shift gears and then release the clutch gradually. Do not speed-shift; allow time for the gears to synchronize. To prevent grinding the gears when shifting into reverse, hold the clutch pedal depressed briefly before shifting, or shift the lever into one of the forward gears before selecting reverse. A safety lockout prevents accidental shifting straight from 5th to Reverse.


Avoid rapid acceleration or sudden deceleration when either or both driving wheels are on a slippery surface. Decreased traction could cause loss of directional control.


CAUTION:


Do not drive with your foot on the clutch pedal as this will cause premature wear of clutch components. Do not shift into reverse while the car is moving.


(cont'd)


Main Menust Shifting the 5 Speed (cont'd)


Maximum Allowable Speeds The speeds shown below are the maximum at which the car can be driven or downshifted in each gear without over-revving the engine.


Recommended Shift Speeds For best fuel economy, and effective emission control, shift at the speeds shown:


Main Menust Shifting the Automatic


The automatic transmission shift lever has a locking mechanism to prevent accidental shifting into Reverse (R), Park (P) or 2nd (2). Also, an Automatic Shift Lock prevents you from shifting out of Park unless the brake pedal is already depressed and the ignition switch is in the II position. Push the button on the shift handle to shift into 2nd, Reverse or Park; depress the brake pedal and then push the button on the shift handle to shift out of Park.


: Depress the brake pedal first and push the button, then shift.


: Push the button, then shift. : Shift as desired.


Depress button


KEY


Insert


SHIFT LOCK RELEASE


If you cannot shift out of Park with the brake pedal depressed and the ignition switch in the II position: 1.Turn the ignition switch off and


remove the key.


2. Insert the key in the Shift Lock Release located to the right of the shift lever.


3. Press and hold the key down, then press the button on the shift handle and move the shift lever to Neutral.


4. Return the key to the ignition switch, depress the brake pedal and restart the engine.


NOTE: If you encounter any problem shifting out of Park, have your authorized Honda dealer check the system as soon as possible.


(cont'd)


Main Menust Shifting the Automatic (cont'd)


Operating Tips For smoother operation, apply the brakes when shifting from Neutral or Park to a forward or reverse gear. When parking: bring the car to a stop with the foot brake, hold the brake on and shift into Park, set the hand brake and then turn off the engine.


NOTE: Your 4 speed automatic transmission is equipped with a torque converter lock-up clutch. Because of this, you may notice what feels like an extra shift as the clutch engages.


CAUTION:


Shift into P only after the car has come to a complete stop. Shift into or out of R only after the car has come to a complete stop. Do not "rev-up" the engine when the brake is on and the shift lever is in D, S, 2 or R. When stopped on a hill, use the brakes to hold your position, not the accelerator pedal. Do not shift from N or P into D, S, 2 or R when the engine is above idle speed. Before shifting into gear, make sure your foot is firmly on the brake pedal. Do not rest your hand on the shift lever or push the shift button while driving.


Driving Technique


D-4th Use the D range for normal in-town and highway driving. The car will start off in 1st and shift automatically to 2nd, 3rd, and 4th. The further down you push the accelerator, the later the transmission will shift and the faster the car will accelerate.


S 3 / S 4
The " S" shift selector range changes the shift points under part throttle acceleration, allowing the transmission to stay in each lower gear for a longer period before automatically upshifting. With the shift selector in the " S" range, the "S3" indicator light in the instrument panel will come on and the transmission will shift from 1st to 2nd and 3rd but not 4th. This is especially useful when climbing or descending grades. While driving in the " S" range, the car's performance is improved but fuel economy is reduced.


Main Menust While driving in the " S" range, you can select 4th gear by pushing the "S4" switch. Depending upon vehicle speed and throttle pedal position, the transmission will shift to 4th gear when the switch is pressed; the "S4" indicator light in the instrument panel will come on. Pushing the "S4" switch again will cause the transmission to downshift to 3rd gear in the "S3" mode. The "S4" indicator light in the instrument panel will go out, and the "S3" light in the instrument panel will come on If the shift lever is moved to any other driving range, the "S4" switch will be cancelled automatically.


S4 SWITCH


NOTE:


In both the D and S modes, the transmission holds in 2nd while you are stopped in gear. When you start moving again, the transmission shifts to 1st, then 2nd and so on. If rapid acceleration is necessary, depress the accelerator to the floor; the transmission will automatically shift down according to load and engine speed. This applies to both D and S ranges.


(cont'd)


Main Menust Shifting the Automatic (cont'd)


2-2nd Use 2nd gear for increased engine braking when driving downhill, and increased power when driving uphill; also for driving on slippery roads, and freeing the car from mud or sand, where 1st gear could provide too much power and cause skidding or wheelspin. The maximum recommended speed in 2nd gear is: 60 mph (97 km/h)


R-Reverse CAUTION: Shift into or out of reverse only after the car has come to a complete stop; the transmission may be damaged if you shift while the car is moving.


P-Park CAUTION: Use this position when starting the engine, or when parking. Shift into Park only when the car is COMPLETELY stopped.


N-Neutral Use when starting the engine or during prolonged idling in traffic.


Main Menust Towing a Trailer


Your car is designed primarily to carry passengers and a normal amount of luggage. Although your car is capable of towing a trailer, there will be an effect on handling, performance, braking, general vehicle and tire durability and fuel economy.


The weight of the trailer plus its cargo must not exceed a total of 1,000 Ibs. (450 kg). The gross vehicle weight must not exceed the Gross Vehicle Weight Rating (GVWR) indicated on the Certification label (see page 131 ). The gross vehicle weight is the total weight of the car, driver, passengers, luggage, hitch and trailer tongue load. The total weight supported by each axle must not exceed the Gross Axle Weight Rating (GAWR). The front and rear GAWR's are shown on the Certification label (page 131 ). The distribution of luggage and passengers in the car, as well as the tongue load and hitch weight should also be considered in terms of the GAWR, which is the maximum amount of weight that should be supported over the front and the rear axles. You should have your car and trailer weighed at a commercial weighing station to check both the GVWR and GAWR's to confirm that the total weight and weight distribution are within safe driving limits. The maximum trailer tongue load must not exceed 100 Ibs. (45
kg). Cargo should be distributed so that the tongue load is approximately 10% of the total weight of the trailer and its cargo. This is done by distributing approximately 60% of cargo weight toward the front of the trailer and 40% toward the rear.


TRAILER WEIGHT


TONGUE LOAD


Maximum: 1,000 Ibs (450 kg)


Maximum: 100 Ibs (45 kg)


Never load the trailer so that the back is heavier than the front. This will seriously affect vehicle handling. Be sure the cargo is secured so that it will not move during driving.


(cont'd)


Main Menust Towing a Trailer (cont'd)


Hitches Use only a hitch recommended by your Honda dealer. The hitch should be bolted securely to the car and installed by a qualified technician. Do not use a hitch designed for temporary installation and never use one that attaches only to the bumper.


Trailer Brakes and Safety Chains The Honda Automobile Division recommends that trailers equipped with brakes should conform to any applicable federal and state regulations. When using a trailer equipped with electric brakes, a trailer brake controller that connects to the car's electrical system is recommended. Installing a brake controller that connects to the car's brake hydraulic system could result in brake fluid contamination or leaks. A safety chain must always be used between the car and the trailer. Leave sufficient slack in the chain so that it does not bind in sharp turns. The chain should cross under the trailer tongue to prevent the tongue from dropping to the ground.


Tires Make sure your car's tires are properly inflated. Adjust tire pressure to the recommended tire pressure indicated on the label attached to the edge of the driver's door. The trailer tires should be of the proper size, load rating and inflated to the pressure recommended by the trailer manufacturer.


Trailer Lights Trailer lights must comply with federal, state and local regulations. See your local recreational vehicle dealer or rental agency for the correct type of lighting and wiring for your trailer. Check for correct operation of the turn signals and stop lights each time you hitch up.


CAUTION: Connections to your car's electrical system should be made by your Honda dealer or a qualified electrician. Improper installation may damage your vehicle's electrical system and cause a malfunction of the lights.


Main Menust Break-in Schedule Do not tow a trailer during the 600 miles (1,000 km) break-in period: see page 2 .


Maintenance If you tow a trailer, your vehicle will require more frequent maintenance due to the additional load. Refer to the "Maintenance schedule under severe driving conditions" on page 82 for specific information.


Before Towing With the car and trailer completely loaded and parked on a level surface, confirm that the tongue loading is correct. If the car has an abnormal nose-up or nose-down attitude, check for improper cargo distribution. Check also for excessive cargo weight, worn suspension or other causes and correct the problem before driving. Be sure the cargo is secured so it will not shift while driving. Check that your rearview mirrors conform to any federal, state or local regulations. If not, install rearview mirrors designed for towing. Before towing a trailer, practice turning, stopping and reversing with a trailer in an area away from traffic until you learn the technique.


(cont'd)


Main Menust Towing a Trailer (cont'd)


Towing Safety


Stopping distance will be increased when towing a trailer. For each 10 mph (16 km/h) of speed, allow at least two car lengths between you and the vehicle ahead. Avoid sudden braking which may cause trailer jackknifing and loss of control. Avoid jerky starts and sudden acceleration. If your car has a manual transmission, always start out in first gear and release the clutch at moderate engine rpm. Avoid rapid lane changing and sharp turns. The trailer could hit your car in a tight turn. Slow down before making a turn. Remember, the total length of your car plus trailer will require a wider turning circle. Crosswinds may adversely affect handling of your car and trailer. Use the rearview mirrors frequently to warn you of approaching large vehicles that may pass you causing your car and trailer to sway. When being passed, firmly grip the steering wheel and be prepared to reduce speed immediately but gradually. Never increase speed. Steer straight ahead. Towing a trailer in bad weather will magnify any difficulty in controlling the car caused by the weather itself. Avoid sudden maneuvers: slow down and use extra caution. Be careful when passing other vehicles. Passing requires considerable distance because of the added weight and length of your trailer.


Main Menust CAUTION:


Before starting out, check the operation of the lights and all car/ trailer connections. After driving a short distance, stop and recheck the lights and connections. Reversing is difficult and requires practice. While backing-up, the trailer may pivot off-course. To correct for this, grip the bottom of the steering wheel and move your hand to the left to move the trailer to the left; or to the right to move the trailer to the right. Turn the steering wheel a little at a time, and keep the speed very low. Have someone guide you when backing. To help prevent overheating of the brakes, shift into a lower gear to make use of engine braking before descending steep or long grades. Do not make sudden downshifts. Pay strict attention to the coolant temperature gauge when going up hills. Because of the added load of the trailer, your car's engine may overheat on hot days. Turning off the air conditioner will reduce the load on the cooling system. On cars equipped with automatic transmission. ' — Do not hold the car stationary on an incline by using the accelerator pedal; this can cause the transmission fluid to overheat. Instead, use the handbrake or foot brake. When towing trailers, avoid high transmission fluid temperatures (caused by the transmission frequently shifting between 3rd and 4th gears) by driving in S3.



NOTE: Be sure to check state and local laws concerning maximum speed or other driving restrictions for cars towing trailers. If you are driving across several states, check each state's requirements before leaving home, because restrictions may vary,


Parking with a Trailer Whenever parking your car on an incline with a trailer attached, place and seat chocks at each wheel of the car and trailer. This is in addition to the normal parking preparations of firmly applying the parking brake and placing the transmission in first or reverse (manual transmission) or P (automatic transmission).


CAUTION: Parking on an incline is not recommended and should be done only if it cannot be avoided. Follow all precautions mentioned above and turn the wheels to point towards a curb if facing downhill, away from a curb if facing uphill. When leaving an inclined parking place, move the car slightly to unseat the chocks. Then while keeping the foot brakes firmly applied, have an assistant remove the chocks.


Main Menust Maintenance Schedule and Records


Your Honda automobile must be properly maintained to ensure that it is in peak operating condition and the emission levels are within the standards set by the Federal Clean Air Act. The following instructions and maintenance procedures are based on the assumption that your car will be used exclusively for the purpose for which it was designed: 1.To carry passengers and cargo within the load limits shown on


the label on the edge of the driver's door.


2. To be driven on reasonable road surfaces within legal limits. 3.To generally be driven daily over a distance of several mites. 4. Use gasoline from pumps labeled unleaded, with a pump octane number of 86 or higher. The pump octane number is an average of the Research (R) octane and Motor (M) octane numbers.


NOTE: Failures which occur due to a lack of maintenance will not be covered under warranty. The Required Maintenance Schedule* specifies all maintenance required to keep your car in peak operating condition. Work should be done by a Honda dealer but may be done by any qualified service facility or individual who is competent in this type of work.


Maintenance, replacement, or repair of emission control devices and systems may be done by any automotive repair establishment or individual using parts that are "certified" to EPA standards. After the maintenance has been done, be sure to complete the Maintenance Records on pages 81 — 83 . All required maintenance is considered normal owner operating cost and you will be charged for it by your dealer. * For vehicles sold in California, maintenance operations indicated by *4 on page 80 are recommended by the manufacturer. Other maintenance operations are required by California regulations and condition the emission warranty.


Main Menust Check the following items at each fuel stop: 1. Engine oil level. 2. Radiator coolant level.


Check the following items periodically: 1. Brakes: for braking efficiency, brake pedal travel and hydraulic


fluid level.


2. Lights: for operation of headlights, taillights, side marker lights,


stoplights, turn signals and back-up lights.


3. Tires: for correct pressures (including spare); inspect for cuts and uneven or excessive wear. Rotate every 7,500 miles (12,000 km) in the pattern shown on page 110 .


4. Steering: for excessive play or vibration while driving. 5. Exhaust system: for leaks or loose mounts. 6. Wipers: for operation of windshield wipers and washer, and


7. Seat belts: for condition of fabric and buckles, and operation of


condition of wiper blades.


the restraint mechanism.


8. Battery condition.


(cont'd)


Main Menust Maintenance Schedule and Records (cont'd)


Check oil and coolant level at each fuel stop. Under severe driving conditions, service these items twice as often. (See page 82)


Main Menust Required Maintenance Record


Have your servicing dealer record all Required Maintenance below. Keep receipts for all work done on your car.


(cont'd)


Main Menust Maintenance Schedule and Records (cont'd)


Severe Driving Conditions CAUTION: The following items must be serviced more frequently on cars normally used under severe driving conditions. Refer to the chart below for the appropriate maintenance intervals.


Severe driving conditions include: A: Repeated short distance driving B: Driving in dusty conditions C: Driving in severe cold weather D: Driving in areas using road salt or other corrosive materials E: Driving on rough and/or muddy roads F: Towing a trailer


R-Replace I -Inspect


After inspection, clean, adjust, repair or replace if necessary.


Non-Scheduled Maintenance Record Record additional maintenance for severe driving conditions or non- scheduled maintenance on this page. (See page 80 )


Main Menust Main Menust Fluid Locations


AUTOMATIC TRANSMISSION FLUID DIPSTICK


ANTI LOCK BRAKE FLUID RESERVOIR (Si with Anti-lock Brake System)


POWER STEERING FLUID RESERVOIR


ENGINE OIL FILLER CAP


RADIATOR RESERVE TANK CAP


CLUTCH FLUID RESERVOIR (Manual Transmission Only)


RADIATOR CAP


ENGINE OIL DIPSTICK


WASHER FLUID RESERVOIR


BRAKE FLUID RESERVOIR


Main Menust Engine Oil and Filter


Checking Check the engine oil a couple of minutes after shutting the engine off, with the car parked on level ground. Remove the dipstick and wipe it clean. Re-insert it all the way down, then pull it out and read the level. The level should be between the upper and tower marks.


DIPSTICK


ENGINE OIL FILLER CAP


UPPER


LOWER


Adding If the level has dropped close to the lower mark, add oil until it is even with the upper mark. 1.Turn the oil filler cap counterclockwise to remove. Add oil, then


check the level again. Do not overfill.


2. Reinstall the cap and twist clockwise until it stops. CAUTION:


Be sure the oil filler cap is correctly replaced before starting the engine. Engine oil is a major factor affecting the performance and service life of the engine, you should use only a premium quality detergent oil labeled SG grade.


LOOK FOR THIS LABEL ON THE OIL CONTAINER


Use the proper viscosity oil for the climate in which you drive:


Ambient Temperature


Some oil labels may also include additional designations of quality such as CC or CD. However, these are acceptable only when used together with SG. NOTE: 5W-30 viscosity oil is recommended for improved fuel economy.


(cont'd)


Main Menust Engine Oil and Filter (cont'd)


Fuel Efficient Oil For the best fuel economy from your car, it is recommended that you use a fuel efficient SG grade oil. This oil is usually identified by the words such as: "Energy Conserving II," "Gas Saving," and "Fuel Saving," etc.


Changing Oil and Filter Engine oil and the filter should be changed together every 6 months or 7,500 miles (12,000 km), whichever comes first. The filter is located on the engine block, below the intake manifold.


CAUTION: The oil filter cannot easily be removed from above the engine. For this reason it is recommended that the oil filter change be done by a skilled mechanic.


1. Start the car to warm up the


engine, then shut it off.


2. Remove the engine oil filler cap


and drain bolt, and drain the oil.


A warmed-up engine and the oil in it are hot; be careful not to burn yourself.


3. Remove the oil filter and let the


remaining oil drain out.


4. Install a new fitter according to the instructions on or with the filter.


ENGINE OIL DRAIN BOLT


OIL FILTER


Main Menust 5. Reinstall the drain bolt with a new washer and tighten it securely. Refill the engine with the recommended oil, to the upper mark on the dipstick.


ENGINE OIL CHANGE CAPACITY (including filter): 3.8 l (4.0 US qt, 3.3 Imp qt)


6. Start the engine and make sure oil is not leaking from the drain


bolt or the filter.


7. Shut off the engine and recheck the oil level.


NOTE: Please dispose of used motor oil in a manner that is compatible with the environment. We suggest you take it in a sealed container to your local service station for reclamation. Do not throw it in the trash or pour it on the ground.


CAUTION: Used motor oil may cause skin cancer if repeatedly left in contact with the skin for prolonged periods. Although this is unlikely unless you handle used oil on a daily basis, it is still advisable to thoroughly wash your hands with soap and water as soon as possible after handling used oil.


Main Menust Transmission Oil/Fluid Check


Transmission oil/fluid must be checked with the engine off and the car on level ground.


If the engine has been running, some engine components may be hot enough to burn you. Keep hands away from the radiator fan. The fan may start automatically without warning and run for up to 15 minutes, even after the engine is turned off.


CAUTION: If the oil/fluid level is low, check for possible leaks before adding oil. Do not overfill.


Since the transmission and differential are in the same housing, you are actually checking both oil/fluid levels in one procedure. Change transmission oil/fluid according to the Maintenance Schedule on page 80


5-Speed Remove the oil filler bolt (beside the right axle). Feel inside the bolt hole with your finger. If the oil is up to the bottom edge of the hole, the oil level is correct. If it is not, slowly add oil until it runs out of the hole, then reinstall the boh and tighten it securely with a wrench.


OIL CHECK FILLER BOLT


CORRECT LEVEL


5-SPEED TRANSMISSION OIL CHANGE CAPACITY; 2.1 l (2.2 US qt, 1.8 Imp qt)


Use only SF or SG grade motor oil when adding or changing transmis- sion oil.


Main Menust Use the proper viscosity oil for the climate in which you drive:


Ambient Temperature


Automatic The automatic transmission fluid level is checked (with the engine off and the car on level ground) using the dipstick in the right end of the transmission housing. Remove the dipstick and wipe it off.


DIP STICK


UPPER LOWER


Insert the dipstick and remove it. The fluid level should be between the upper and tower marks. If necessary, add fluid and recheck. Use only DEXRON ® II Automatic Transmission Fluid (A.T.F.) when adding or changing fluid. After checking the fluid level, push the dipstick in securely.


AUTOMATIC TRANSMISSION FLUID CHANGE CAPACITY: 2.8 l (3.0 US qt, 2.5 Imp qt)


Main Menust Cooling System


The engine in your Honda contains a number of aluminum parts. Therefore, it requires an antifreeze/coolant specifically formulated to protect the aluminum parts from corrosion. Failure to use a suitable antifreeze/coolant may seriously shorten the life of the engine as the result of rapid corrosion damage. Some antifreeze/ coolants, although labeled for use in engines containing aluminum, may not provide adequate protection for your engine. Therefore, use only a Honda RECOMMENDED antifreeze/coolant. CHECK WITH YOUR AUTHORIZED HONDA DEALER. For best corrosion protection, the mixture of coolant and water must be maintained year-round at 50/50. Concentrations less than 50% coolant may not provide sufficient protection against corrosion and freezing. Concentrations of greater than 60% coolant will impair cooling efficiency and are not recommended. Low- mineral drinking water or distilled water should be mixed with the antifreeze/coolant. Coolant loss should be replenished by a mixture containing the proper concentration of antifreeze and water. Do not mix different antifreeze/coolants. Do not use additional rust inhibitors or anti-rust products, as they may not be compatible with the radiator coolant. ENGINE DAMAGE CAUSED BY IMPROPER COOLANT USAGE IS NOT COVERED BY THE NEW CAR WARRANTY.


Checking Coolant Check the coolant level in the reserve tank when the engine is at normal operating temperature (with the engine off and the car on the level ground), using the dipstick in the reserve tank. Remove the dipstick and wipe it off. Insert the dipstick and remove it. The coolant level should be between the MAX and MIN marks.


Do not remove the radiator cap when the engine is hot; the coolant is under pressure and could severely scald you. Keep hands away from the radiator fan. The fan may start automatically without warning and run for up to 15 minutes, even after the engine is turned off.


Main Menust If the level is between the MIN and MAX marks on the dipstick add a 50/50 solution of antifreeze and water to bring it up to MAX. If there is no coolant visible on the dipstick, the cooling system should be checked for teaks and repaired if necessary. Coolant must then be added to the radiator.


MAX


MIN


RESERVE TANK


CAUTION: Radiator coolant will damage paint. Quickly rinse any spilled coolant from painted surfaces. Wait until the engine is cool, then turn the radiator cap counterclock- wise until it stops. DO NOT PRESS DOWN WHILE TURNING THE CAP. After any remaining pressure has been relieved, remove the cap by pressing down and again turning it counterclockwise. Add enough coolant to fill the radiator, and reinstall the cap. Be sure to tighten it securely. Fill the reserve tank up to the MAX mark with the engine cold. Maintenance 1. Check the freeze protection level of the coolant with a hydrome- 2. Keep the front of the radiator free of dirt and debris. 3. Check hoses and hose clamps regularly.


ter.


Main Menust Cooling System (cont'd)


Thermostat The thermostat in the cooling system does not need to be changed for summer or winter operation. However, for extremely cold climates, an optional thermostat is available from your Honda dealer.


Replacing Coolant Replace coolant at 36 months or 45,000 miles (72,000 km), which- ever comes first. Thereafter, replace every 2 years or 30,000 miles (48,000 krn), whichever comes first.


RADIATOR COOLANT REFILL CAPACITY: (Including reserve tank) 6.15 l (1.625 US gal, 1.353 Imp gal)


0.75 l (0.198 US gal ,0.165 Imp gal)


1. Set the heater temperature lever to maximum heat. 2. Remove the radiator cap and loosen the drain plug when the


radiator is cool, and drain the radiator.


RADIATOR CAP


BLEED BOLT


DRAIN PLUG


DRAIN BOLT


3. Remove the drain bolt from the front side of the cylinder block,


and drain the engine and heater.


4. Apply non-hardening sealant to the drain bolt threads, then rein-


stall the bolt and tighten it securely.


5. Tighten the radiator drain plug securely.


Main Menust 6. Mix the recommended antifreeze with an equal amount of tow- mineral or distilled water and fill the reservoir to maximum, as illustrated.


Fill to here


7. Loosen the air bleed bolt in the thermostat housing, then fill the radiator to the filler neck with the coolant mixture. Tighten the bleed bolt as soon as coolant starts to run out in a steady stream without bubbles.


FILLER NECK


Fill to here


8. With the radiator cap off, start the engine and let it run until warmed up (fan goes on at least twice). Then, if necessary, add more coolant mix to bring the level back up to the filler neck.


9. Put the radiator cap on, then run the engine again and check for


leaks.


Main Menust Spark Plugs


Spark plugs should be replaced every 24 months or 30,000 miles (48,000 km), whichever comes first. Recommended spark plugs:


For all normal driving


ZFR5F — 11 (NGK) K


J16CR — L11


(ND)


For hot climates or continuous high speed driving


ZFR6F— 11 (NGK) KJ20CR —


L11


(ND)


Keep hands away from the radiator fan. The fan may start automatically without warning and run for up to 15 minutes, even after the engine is turned off.


CAUTION: Never use spark plugs with an improper heat range; they will adversely affect engine performance and durability.


Main Menust Spark Plug Replacement


Replace plugs one at a time, so you don't get the wires mixed up. 1. Clean any dirt from around the spark plug base. 2. Disconnect the plug cap, then remove and discard the old plug. 3. Check the gap of the new spark plug before installation.


Plug gap should be: 1.1 mm (0.04. in)


4. Thread the new spark plug in by hand to prevent cross-threading. 5. After the plug seats against the cylinder head, tighten 1/2 turn


with a spark plug wrench to compress the washer.


6. Reinstall the spark plug cap.


PLUG CAP


Thread by hand


CAUTION: The spark plugs must be securely tightened, but not overtightened. A plug that's too loose can get very hot and possibly damage the engine; one that's too tight could damage the threads in the cylinder head.


Main Menust Wiper Blades


For maximum visibility, replace worn or cracked wiper blades when you notice they do not wipe the windshield cleanly or smoothly.


To Replace Worn-out Blades 1. Detach the blade assembly from the arm by pressing the lock tab in, then pushing the blade toward the base of the arm.


Push


2. Firmly grasp the end of the blade rubber and pull until the tabs are free of the metal support.


METAL SUPPORT


TAB


Press Lock Tab in


Pull out


3. Remove the metal retainers from the worn-out blade rubber and put them in a new blade rubber.


RETAINERS


4, Insert the new blade rubber from the opposite side of the blade tabs and position the tabs in the metel support.


5. Reinstall the blade assembly on


the wiper arm.


Push in


Main Menust Air Filter


Replace the air filter every 24 months or 30,000 miles (48,000 km), whichever comes first (more often in extremely dusty conditions).


Replacement Loosen the air filter band. Loosen the attaching bolts and remove the filter cover and seal. Remove the old filter and replace it with a new one, reinstall the seal and cover. Tighten the bolts.


COVER


BAND


BOLT


SEAL


AIR FILTER


Main Menust Fuel Filters/Clutch Fluid


Fuel Filters The fuel filter is located in the engine compartment, on the right center of the lower dashboard. It should be replaced at 60,000 miles (96,000 km) or 48 months whichever comes first, or any time you suspect contaminated gas may have clogged it.


CAUTION: Because the fuel system is under pressure, the filter should be replaced only by a qualified Honda technician.


CLUTCH FLUID RESERVOIR


Clutch Fluid Check the fluid level in the clutch reservoir periodically; it should be between the MAX and MIN marks on the reservoir. If the level is near the MIN mark, add fluid to raise it to the MAX mark. Do not overfill. Use only brake fluid manufactured to DOT 3 or DOT 4
specifications from a sealed con- tainer. Follow the manufacturer's in- structions printed on the can.


NOTE: A low clutch fluid level may be an indication of clutch fluid leakage. You should have your clutch checked if the clutch fluid level in the reservoir is low.


Main Menust Power Steering


The power steering on your car provides easy handling while parking and maneuvering in traffic, without loss of road "feel" at highway speeds. An engine-driven hydraulic pump provides full power assist at low speeds and decreasing assist as the car goes faster.


CAUTION: If the power steering system should fail, or if the engine should stall, the car can still be steered. However, much greater effort will be required, particularly in sharp turns at low speed.


NOTE: You may feel a slight clunk or knock when turning the wheel with the engine off. This is a normal condition due to the design of the system.


Power Steering Fluid Check the power steering fluid level with the engine cold and the car parked on level ground. Make sure the fluid level is between the upper and lower marks on the reservoir. If the level has dropped close to or below the lower mark, check for leaks before adding fluid to the upper mark. Do not overfill.


POWER STEERING FLUID RESERVOIR


CAUTION: Use only genuine Honda power steering fluid. The use of other fluids such as A.T.F. or other manufacturer's power steering fluid will damage the system.


Main Menust Brakes


Brake System Design The diagonally-separated dual serv- ice brake system is designed so half the system will still provide braking action if the other half fails. Stopping the car after losing the brake fluid from half the system will require more pedal pressure and pedal travel than normal. Also, the distance required to stop will be longer using only half the brake system. If the brakes fail suddenly, downshift to a lower gear for increased engine braking, and pull off the road as soon as possible.


It is dangerous to drive your car with a problem in either the brake electrical or hydraulic system; have your dealer check both systems if you suspect brake trouble. Do not ride the brakes. In other words, don't put your foot on the brake pedal unless you intend to brake. This causes excessive brake wear and can damage, or lead to loss of braking effectiveness through overheating. Your brake lights may also confuse drivers behind you. Driving through deep water may affect the brakes. Check their effectiveness by pressing the brake pedal gently. if the car does not slow down at the normal rate, continue gently applying the brakes, while maintaining a safe speed, until they dry out and normal performance returns.


Brake Wear Both front and rear brakes should be inspected for wear at the intervals shown in the Maintenance Schedule on page 80 . When the brakes require maintenance, use only genuine Honda replacement parts or their equivalent.


Brake Wear Indicators Your car is equipped with audible brake wear indicators. When the brake pads need to be replaced, the wear indicators will make a "screeching" sound or a high pitch chirp.


NOTE: Due to some driving habits or climates, brakes may "squeal" when you first apply them or when you have them partially applied; this is normal, and does not indicate excessive wear. The wear indicator makes a "screeching" sound while the brakes are applied.


Main Menust BRAKE FLUID RESERVOIR


Brake Fluid Check the fluid level in the brake reservoir periodically; it should be between the MAX and MIN marks on the reservoir. If the level is near the MIN mark, add fluid to raise it to the MAX mark. Do not overfill. Use only brake fluid manufactured to DOT 3 or DOT 4
specifications (see reservoir cap) from a sealed container. Follow the manufacturer's instructions printed on the can.


NOTE: A low brake fluid level may be an indication of brake pad wear or of brake fluid leakage. You should have your brakes checked if the brake fluid level in the reservoir is low before re-filling it.


CAUTION: The arrow on the reservoir cap must be pointing forward after the cap is instated. Make sure the brake warning switch wiring doesn't get caught between the cap and top edge of the reservoir.


ANTI-LOCK BRAKE FLUID RESERVOIR


Anti-lock Brake Fluid (Si with Anti-lock Brake System) Check the fluid level in the Anti-lock brake reservoir periodically. To check, drive the car for a few minutes to equalize fluid pressure in the system. The level should be between the MAX and MIN marks on the reservoir. If the level is near the MIN mark, add fluid to raise it to the MAX mark. Do not overfill. Use only brake fluid manufactured to DOT 3 or DOT 4
specifications from a sealed contain- er. Follow the manufacturer's instruc- tions printed on the can. If the level is more than 10 mm (0.4 in) above the MAX mark, it may indicate a malfunction of Anti-lock brake system. Have an authorized Honda dealer check the system as soon as possible.


MIN LEVEL


MAX LEVEL


Main Menust Battery


The condition of the battery can be determined by checking the test indicator. Service as required according to the label on the battery. Any corrosion around the positive and negative terminals should be washed off with a solution of baking soda and warm water. Dry the terminals and then coat them with grease.


TERMINAL


TERMINAL


TEST INDICATOR


The battery gives off explosive gases; keep sparks, flames and cigarettes away. Provide adequate ventilation when charging or using the battery in an enclosed space. The battery contains sulfuric acid (electrolyte). Contact with skin or eyes may cause severe burns. Wear protective clothing and a face shield. —If electrolyte gets on your skin, flush with water. —If electrolyte gets in your eyes, flush with water for at least


15 minutes and call a physician immediately.


Electrolyte is poisonous. —If swallowed, drink large quantities of water or milk and follow with milk of magnesia or vegetable oil and get immediate medical assistance.


KEEP OUT OF REACH OF CHILDREN.


Main Menust Fuse Replacement


The fuse boxes are located under the dashboard on the driver's side and on the right front fender beside the battery. The circuits protected by each fuse are listed on the plastic sheet in the box.


FUSE BOX COVER


If any of your car's lights, accessories, or controls don't work, check their fuses. If a fuse has blown, the wire inside it will be burned through.


Blown


FUSE REMOVER


Checking the fuses: 1 .Turn off the ignition and all other switches. 2. If you find a blown or possibly faulty fuse, use the fuse remover (located inside the fuse box under the dashboard) to pull the blown fuse out of its clips.


3. Check all other fuses as well as the one you suspect. 4. Push in a new fuse of the same rating, and make sure ft fits tightly


in the clips. If it fits loosely, have your dealer fix it. If you don't have a spare, take a fuse of the same rating (or lower) out of a circuit you may not need, like the radio or cigarette fighter. Remember to replace the borrowed fuse and the missing spares.


(cont'd)


Main Menust Fuse Replacement (cont'd)


CAUTION: A blown fuse may be just a symptom of some other problem. If a new fuse blows right away, the cause should be diagnosed and corrected by a qualified Honda technician. Never replace a fuse with anything but another fuse of the same or lower rating. A higher capacity fuse could cause damage and even start a fire.


The main fuse and some primary fuses are installed in the fuse box on the right front fender In the engine compartment. MAIN FUSE: (65A)


SUNROOF FUSE:


(35A)


If the circuits from the battery are ever overloaded (by a short in the system drawing too much current for example) the main or a primary fuse will blow, preventing damage to the entire wiring harness. If the main fuse blows, have a Honda dealer check the system, repair the cause, and replace the fuse.


CAUTION:


The electrical system is protected by fuses that are designed to fail and prevent damage to the wire harness. Always replace blown fuses with the same rating as specified to prevent wiring damage that can result in a possible fire. For proper electrical contact after replacing these fuses, make sure all screws are tight.


Main Menust Bulb Replacement


NOTE: See page 130 for bulb specifications.


Front turn signal lights, and position lights


Rear side marker, turn signal, brake/taillights and back-up lights


Front side marker/turn signal lights


(cont'd)


Main Menust Bulb Replacement (cont'd)


License plate lights


Trunk light


High-mount brake light


Interior light


Main Menust Tires


The factory installed tires on your car were selected to match the car's performance capabilities and to provide the best combination of handling, ride comfort and tread wear. We recommend that you get the same size, type, and grade of tires when replacement is necessary. If your tires have an all-season tread design, the model name will be followed by the marking: "M + S" (mud and snow) or "all-season". If you decide not to get the same brand of tires as those originally installed, you should make sure that the replacements are the radial type, of the same size, load range and speed rating as the original tires. If you have any questions about your car's tires, please contact your Honda dealer.


tire pressures


the d r i v e r 's door


inflation Pressures The tire label attached to the edge lists of recommended for carrying loads up to the limit shown. (Tire pressures are also listed on the back cover of this manual.) These pressures were chosen to provide you with the best combi- nation of tread life, riding comfort and stability under normal driving conditions. Improper inflation can reduce both tire life and load carrying capacity. Check the tire pressures at least once a month, including the spare. Lower pressure than recommended lets the tread and sidewafls flex too much, causing increased tire temperatures, uneven wear, and poor handling. Pressure higher than recommended can make the tire too stiff, increasing the chance of damage from road hazards, and also causing uneven wear. CAUTION:


TIRE LABEL


Check tire pressure when the tires are cold. (After the car has been parked for more than 3 hours or driven less than 1 mile/1.6 km.) Tire pressure may increase as much as 41 kPa (6 psi) when the tire is hot, so NEVER ADJUST tire pressure when the tires are hot. Never inflate load range B tires to more than 220 kPa (32 psi) cold. Cars with luggage racks or cartop carriers DO NOT have greater load limits than those on the label.


(cont'd)


Main Menust Tires (cont'd)


Winter Driving Tires marked "M + S" or "all season" have an all-weather tread design and should be suitable for most driving conditions. However, snow tires and tire chains may be required under some conditions. If your tires do not have these markings, they may not be suitable for winter driving conditions. We recommend snow tires or tire chains for snow and icy conditions.


Snow Tires If you use snow tires, they should be of the same size, construction and load capacity as the original tires on your car. Snow tires must be installed in sets of four, or they may cause poor handling. Driving with snow tires on dry roads can reduce your car's performance during acceleration, turning and stopping. If you need further information on snow tires, please contact your Honda dealer.


Tire Chains Use chains only when you have to. Check with local authorities or Provinces for requirements prior to installing tire chains. Make sure the chains are the right size for your tires. Install them only on the drive wheels of your car, and do so as tightly as possible, following the manufacturer's instructions. If metal chains are used, they must be SAE Class " S ." Cable type traction devices can also be used. Drive slowly with chains installed. If you hear the chains contacting your car's body or chassis, stop and tighten them.


CAUTION:


If the contact continues, slow down until it stops or your car can be damaged. Chains that are the wrong size or improperly installed can damage your car's brake lines, suspension, body, and wheels.


If you need further information on tire chains, please see your Honda dealer.


Remove the chains as soon as the road is clear of ice and snow.


Main Menust Tire Replacement Honda recommends that you replace tires in sets of four, or in pairs, front or rear. If you need to replace only one tire, mount the new tire opposite the tire showing the least amount of wear. For instance, if the left front tire shows the least amount of wear, mount the new tire on the front right side. The original tires on your car have tread wear indicators to indicate when they should be replaced. The indicators appear as bands about 12.7 mm (1/2 in) wide when the tire tread depth is less than 1.6 mm (1/16 in). When indicators appear across two or more grooves in a row, you should replace the tire.


INDICATOR LOCATION MARKS


TREAD WEAR INDICATORS


Driving on worn-out tires is very hazardous, and will reduce braking effectiveness, steering accuracy and traction.


When replacing tires, use only the recommended tire size. Wheel rim widths and offsets must be those recommended by American Honda Motor Co., Inc. Contact the Zone Office nearest you as shown on the inside of the back cover.


Tires and wheels other than those recommended may be unsafe. Do not mix radial and bias ply tires on the same car.


Tire Balancing


Unbalanced tires may affect handling and tire wear. A tire should always be rebalanced after it has been dismounted from the wheel.


Your original tires were properly balanced before the car left the factory, but may need rebalancing at some time during the life of the tire. Tire balancing for the COMPACT spare is not necessary.


CAUTION: Use only genuine Honda aluminum wheel weights if your car is equipped with aluminum wheels. Non genuine Honda wheel weights may corrode and damage the aluminum wheel.


(cont'd)


Main Menust Tires (cont'd)


Tire Rotation Tires may wear unevenly when used for a long time in the same position on the car. To avoid this, rotate the tires every 7,500 miles (12,000 km). If abnormal or uneven wear develops between rotations, the cause should be found and corrected as soon as possible. The illustration shows how the tires can be rotated. The COMPACT spare tire must not be included in tire rotation.


NOTE: Brake pads should be inspected for wear whenever the tires are rotated.


Front


Tire Traction


Worn tires or slippery road surfaces can reduce driving, cornering and braking traction. To reduce the possibility of losing traction, slow down when the road gets slippery, replace tires when wear indicators are visible, and KEEP TIRES PROPERLY INFLATED.


Main Menust Air Conditioner Care


Condenser and Radiator Check the engine radiator and the air conditioner condenser (in front of the radiator) for accumulated dirt, insects or leaves. Carefully brush or hose them off to assure maximum cooling performance.


CAUTION: Radiator and condenser fins are very thin and easily damaged; do not bend them with the high water pressure or brush.


Compressor Drive Belt Check the compressor belt tension monthly, during periods when you use the air conditioner a lot.


If the engine has been running, some engine components may be hot enough to burn you.


When pushed with 98 N (22 Ib) of force midway between the compressor drive pulley and the engine crankshaft pulley, the belt should deflect about: 10 — 12 mm (0.4 — 0.5 in)


ADJUSTER


CRANKSHAFT PULLEY


COMPRESSOR DRIVE PULLEY


(cont'd)


Main Menust Air Conditioner Care (cont'd)


System Maintenance Run your air conditioner at least once a week for about ten minutes, even during the off season, to lubricate the seals and the inside of the compressor and, to verify that the system is functional.


If the air conditioner is not cooling properly, it may indicate an undercharged system. Have your dealer check the system for leaks, then evacuate and charge the system with refrigerant 12. Charging quantity: 850 — 950 g (30.1 — 33.6 oz)


CAUTION: Prolonged use of an undercharged system may damage the compressor.


Main Menust Appearance Care


Interior Trim Remove dust and loose dirt with a vacuum cleaner. Wipe the vinyl with a clean, damp cloth or sponge. Stains can be removed with a commercially available vinyl cleaner.


CAUTION: Do not use thinner, gasoline, kerosene, naphtha or other solvents on the interior. They are toxic, flammable and hazardous and could damage the material you're cleaning.


Windows A 10 to 1 mix of water and white vinegar, or a commercially available glass cleaner may be used to clean windows and to remove the dust film sometimes caused by the ingredients used in interior vinyls and plastics.


NOTE: Do not put this solution in the windshield washer reservoir, it will damage the windshield washer pump.


Be careful not to scratch or damage the defogger wires when clean- ing the inside of the rear window; wipe the window horizontally along the wires, not up and down. Dry the windows with a lint-free cloth or paper towel. Keep all the windows clean for maximum visibility.


Exterior Care


Waxing Wax the car when water will no longer "bead" on the paint. Always wash and dry the car before you wax it. Use a good quality liquid or paste wax, and follow the manufacturer's instructions. Wax all the metal trim to keep its luster.


NOTE: Removing oil, tar, etc., with a spot remover will usually strip the wax from the surrounding finish. Be sure to re-wax these areas even if the rest of the car does not yet need waxing.


(cont'd)


Main Menust Appearance Care (cont'd)


Washing NOTE: Retract the headlights before washing the car. However, make sure the headlight lenses are cleaned periodically.


Rinse all loose dirt off the car by spraying it with lukewarm or cold water. Do not use hot water. Wash using a soft-bristle brush, sponge or cloth with water containing a mild detergent such as a liquid dishwashing detergent. Remove oil, tar, tree sap, etc., with tar remover or turpentine. Remove road salt, insects, etc., with mild detergent and lukewarm water. Any of these substances may damage the finish if left on painted surfaces. Rinse the car well. Promptly wipe with a chamois or soft towel to prevent water-spotting. Do not let water or soap air-dry on painted surfaces. During wiping, inspect the surface for stone chips and scratches; paint them with touch-up paint so they won't rust (touch-up paint is available through your Honda dealer). For further instructions on corrosion protection, refer to the Rust Prevention section on page 115.


Aluminum Alloy Wheels (Si) CAUTION:


Wash the wheels after driving on snowy or icy roads where salt has been applied. Avoid off-road driving. Brush, rocks, dirt and severe impact may damage the wheels. Install tire chains carefully. Improperly installed chains can cause damage to the wheels. Honda aluminum wheels are treated with a protective finish. Wash them with a tow-phosphate detergent and sponge. Do not use abrasive cleaners or stiff brushes. Always install aluminum wheels in sets of four. If mixed with other types, the car's handling may be affected.


Main Menust Rust Prevention Rusting is likely to occur in parts of the car where water is trapped or where there is continual dampness.


Water will collect inside doors and body panels if drain holes become clogged. Water which seeps under or soaks floor mats will subject floor sections to prolonged wetness or dampness. Road dirt or sand, which collects and fills recesses on the underside of the car, retains moisture long after the rest of the car has dried.


The removal of paint and undercoating by stones, gravel, and minor accidents immediately exposes metal to air and moisture. Rusting is increased by high humidity and by the presence of corrosive substances in the air or on the roads.


Salt used for road de-icing will coat the bottom of the car and hasten rusting. Localities with high humidity have greater potential for rust problems, especially where salt is also present on the road or in moist sea air. Industrial pollution will accelerate the deterioration of paint finishes and promote rusting.


rear suspension,


above subframe,


under rear bumper.


Preventive Service Check all drain holes in the doors and body panels for clogging and clear if necessary. When washing your car, also clean the underside of the car by using high pressure water; inside front fender, and After washing your car or after heavy rain, check for leaks. White checking for leaks, lift the floor mats in the passenger, cargo and spare tire areas, and check beneath them. Water can collect in these areas and remain unseen for prolonged periods. Dry any wet areas of your car's interior. Remove and dry wet floor mats. Have leaks repaired as soon as possible. After driving your car, wipe off any road dirt or salt on the radio antenna, with it fully extended.


inside rear wheel housing,


(cont'd)


Main Menust Body Repair


Replacement Body and Fender Parts if your vehicle incurs body damage and requires replacement parts, we encourage you to use only Genuine Honda sheet metal body and fender parts. Many insurance companies are specifying imitation sheet metal parts for collision repairs in an effort to reduce claim costs; however, if imitation parts are used the following conditions may apply:


There is no assurance that imitation parts will equal the fit and finish of Genuine Honda sheet rnetal parts; and in our experience they often do not. There is no assurance that imitation parts will resist corrosion as well as Genuine Honda sheet metal parts. Imitation sheet metal parts are not covered by the Honda Limited Warranty.


To ensure your continued satisfaction with your Honda vehicle in the event of an accident, contact your insurance adjuster and insist on Genuine Honda parts in the repair of your vehicle.


Main Menust Spare Tire


COMPACT Spare Tire Your car is supplied with a COMPACT spare tire and wheel for temporary use only in the event of a flat tire. Use the COMPACT spare only when you have to, and only to go as far as the next garage or dealer to have the regular tire repaired and reinstalled.


Because you will rarely use the COMPACT spare, be sure to regularly check its condition and air pressure (415 kPa, 60 psi), so it will be ready when you need it. This type of tire holds less air at higher pressure than a regular tire, so it will inflate (or deflate if there is a leak) more rapidly; check its pressure often and add air gradually if it needs any.


The COMPACT spare tire has a different tire size, air pressure re- quirement, tread fife and maxi- mum speed rating than the four regular tires on your car. Disre- garding these warnings may re- sult in tire failure, loss of vehicle control and possible injury to vehicle occupants. Do not exceed 50 mph (80 km/h) under any circumstances when using the COMPACT spare. Do not mount snow chains on the COMPACT spare. They will not fit properly and will damage the tire and possibly your car. if you must use the COMPACT spare when driving on roads covered with snow or ice, use it as one of the rear tires and mount chains only on the front two regular tires.


(cont'd)


Main Menust Spare Tire (cont'd)


The COMPACT spare tire has a much shorter tread life than regu- lar tires. Replace the tire as soon as tread wear indicators appear as solid bands across the tread. Replace with a tire of exactly the same size and construction.


TREAD WEAR INDICATOR


INDICATOR LOCATION MARK


The COMPACT spare tire and wheel set was designed espe- cially for your car; do not use it on any other vehicle; do not in- stall any other tire on this wheel which is not identical to the original in size and construction, and do not use the COMPACT spare tire on any other wheel. Because the COMPACT spare is smaller in size and higher in air pressure than a regular tire, it will ride more harshly with less ground clearance and may have less traction on some road surfaces. Drive cautiously.


Main Menust Changing a Flat Tire


Do not attempt to change a tire unless the car is on firm, level ground and well out of the flow of traffic.


Park the car on a firm, level surface, apply the parking brake, turn on the hazard warning switch and put the transmission in gear (Park for automatic).


1. Remove the jack, lug wrench/jack handle and jack handle


extension (in the tool bag) from the location shown.


NOTE: To remove the jack, release its tension against the mount by turning the screw counterclockwise.


2. Remove the spare tire. 3. Place blocks in front and back of the wheel diagonally opposite


the tire you are changing.


COMPACT SPARE


TOOL BAG


JACK


(cont'd)


Main Menust Changing a Flat Tire (cont'd)


4. (2,0 Si)


Remove the center cap from the wheel cover by turning the lock to 90°.


(Si) Remove the center cap from the wheel by prying it out with a common flat screwdriver (not provided in the tool bag).


(2.0 Si)


(Si)


CENTER CAP


CENTER CAP


FLAT SCREWDRIVER


CAUTION: (On the Si model) Hold the center cap with your hand then pry it off using a rag to protect the cap and the wheel.


RAG


5. Use the lug wrench to loosen the wheel lug nuts counterclock-


wise one-half turn.


Follow tire changing preparations and procedures carefully to reduce the possibility of injury. The jack is designed for changing tires only. STAND CLEAR, DO NOT get under the car and DO NOT run the engine when the car is supported only by the jack.


6. Place the jack under the jack point nearest the wheel you are removing; align the jack head so the car frame will fit in the recess as you raise the jack.


To reduce the possibility of injury, be sure to use the jack provided with the car and the correct jacking points; never use any other part of the car for jack support.


Main Menust 7. Set the jack handle extension in the connector on the end of the jack and install the lug wrench/jack handle. Turn the lug wrench/ jack handle clockwise until the tire is slightly off the ground.


JACK HANDLE EXTENSION


LUG WRENCH/JACK HANDLE


8. Remove the lug nuts, wheel cover and wheel.


(Wheel cover is equipped with 2.0 Si model)


WHEEL COVER


NUT


VALVE


9. Everytime you install the wheel on the brake hub, use a rag to wipe any dirt off the mounting surface of the hub and the wheel. This will assure a tight, even contact between the wheel and hub.


10. Install the spare, and lug nuts hand tight.


(cont'd)


Main Menust Changing a Flat Tire (cont'd)


11. Lower the car, remove the jack, then tighten the lug nuts


securely in an " X" pattern as shown.


TIGHTENING TORQUE 110 N.m (11 kg-m, 80 lb-ft)


12. Tighten the lug nuts to the recommended torque is:


110 N.m (11 kg-m,80 Ib-ft) If a torque wrench was not used, ask an authorized Honda dealer to verify the torque as soon as possible.


13. Stow the damaged tire in the trunk. 14. Repair or replace the damaged tire as soon as you can, reinstall it


in its original position, then put the spare back in the car.


CAUTION: Always stow the jack, tools and tire securely to prevent them from becoming dangerous projectiles in an accident.


15. Secure the tire and the spacer as shown in the illustration.


(Except for Si with Anti-lock Brake System)


SPACER


SPACER


COMPACT SPARE


DAMAGED TIRE


Main Menust Jump Starting


To start a car with a dead battery, use another battery of the same voltage, and the proper jumper cables.


Procedures other than those below could cause injury or damage from battery acid spray, explosion or charging system overload. Never connect the jumper cable directly to the negative post of the "dead" battery. Never allow the two cars to touch each other. Never allow the jumper cable clamps to touch each other. Never lean over the battery when making connections. Never attempt to jump start a vehicle with a frozen battery. The battery could rupture and explode. If you suspect a frozen battery, remove the vent caps and check the fluid. If there seems to be no fluid, or if you see ice, do not attempt a jump start until the fluid thaws.


CAUTION: If jumper cables are connected backwards, the car's mam fuse may blow.


1. Turn off all lights, heater and other electrical loads, set the parking


brake, and shift the transmission to Neutral or Park.


2. Use one cable to connect the positive terminal of the booster


battery to the positive terminal of the "dead" battery.


Do not attach cable here


DEAD BATTERY


Positive to positive


BOOSTER BATTERY


Negative to the engine, not to the battery


(cont'd)


Main Menust Jump Starting (cont'd)


3. Use the other cable to connect the negative terminal of the


booster battery to the engine at the ground cable as shown,


4.To remove the cables, reverse the above procedures exactly.


DO NOT push or tow a car to start it. The forward surge when the engine starts could cause a collision. Also, under some conditions, the catalytic converter could be damaged. A car equipped with an automatic transmission cannot be started by pushing or towing.


NOTE: (Si with Anti-lock Brake System) After jump-starting the car, there is a possibility that the Anti-lock brake system warning light may come on due to insufficient battery voltage. After the battery is sufficiently recharged and the engine is turned off and restarted, the Anti-lock brake system warning light should indicate that the Anti-lock brake system is OK, by coming on for a few seconds each time the engine is started. If the light remains on after recharging, have it checked by a Honda dealer.


Main Menust If towing is necessary, contact a professional towing service. Your authorized Honda dealer can assist you with detailed towing instructions.


Towing


Never use tow chains or rope to tow a car; your ability to safely control the car may be adversely affected.


We recommend the following: Flat Bed Equipment — Entire car is winched on a flat bed vehicle. This is the best way of transporting your Honda. Wheel Lift Type — Tow with the front wheels off the ground.


If the car can only be towed with the front wheels on the ground: make sure the transmission is full of fluid (see pages 88 — 89 ) and tow with the transmission in neutral (N) and the ignition key in the I position.


CAUTION: To avoid serious damage on automatic transmission cars, first start the engine and shift to D, then to N and shut the engine off. if the engine does not run or the transmission cannot be shifted while the engine is running, the car must be transported on flat bed equipment.


Check local regulations for towing.


CAUTION:


Do not exceed 35 mph (55 km/h) or tow for distances of more than 50 miles (80 km). if a sling type tow is used, the tow truck driver should position wood spacer blocks between your car's frame and the chains and lift straps to avoid damaging the bumper and the body. Do not use the bumpers to lift the car or to support the car's weight while towing. When towing a car with 4WS even with the front wheels off the ground, turn the wheels straight ahead and tie the steering wheel in place.


Main Menust If Your Car Gets Stuck


If your car gets stuck in sand, mud, or snow, call a professional towing service for assistance in getting your car out.


CAUTION:


Do not rev up the engine and allow the wheels to spin freely at high speed. Severe transmission damage may result if the wheels are allowed to spin for more than a few seconds. DO NOT try to free a car with automatic transmission from snow, etc. by rocking the car alternately between forward and reverse gears. Severe transmission damage may result from shifting into gear with the wheels moving.


Main Menust Headlight Motors


Proceed as follows if either headlight motor fails to operate: 1.Lift


the cover


remove


from


the engine


the hood and compartment fuse box.


FUSE BOX


RIGHT HEADLIGHT MOTOR


LEFT HEADLIGHT MOTOR


RIGHT HEADLIGHT


LEFT HEADLIGHT


2. Use the label on the fuse box cover to locate the fuse for the headlight motor that doesn't work. Remove the fuse with the fuse remover located in the fuse box under the dashboard.


FUSE REMOVER


FUSE BOX COVER


(cont'd)


Main Menust Headlight Motors (cont'd)


3. If the fuse has blown, replacing it with a new fuse of the same amperage should allow the motor to work, However, if the fuse hasn't blown, or if a new fuse did not solve the problem, remove the fuse and operate the headlight motor manually.


BLOWN FUSE


CAUTION: Always remove the fuse before manually operating a headlight motor, otherwise the motor may suddenly activate. 4. Remove the cap from the top of the headlight motor, then turn the knob in the direction of the arrow (clockwise) until the headlight is as far up or down as it will go.


CAP


Turn knob In direction of arrow


NOTE: If foreign matter is the cause of the motor malfunction, it can usually be dislodged by turning the knob counterclockwise. 5. Replace the cap properly. 6. Reinstall the fuse and fuse box cover and have the headlight


motor inspected at the earliest opportunity.


Main Menust Specifications


*1 Including the coolant in the reserve tank (0.75 l /0.79US qt/0.66 Imp qt)


but excluding that remaining in the engine.


*2 Excluding the oil remaining in the engine,but including that remaining in the oil filter.


(cont'd)


Main Menust Specifications (cont'd)


Main Menust Identification Numbers


The Vehicle Identification Number (V.I.N.) is stamped on a plate attached to the top left side of the dashboard. It also appears on the Certification label attached to the door jamb, as well as under the hood on the body, directly behind the air cleaner.


NOTE: The V.I.N. is also provided in bar code on the Certification label.


VEHICLE IDENTIFICATION NUMBER


CERTIFICATION LABEL


VEHICLE IDENTIFICATION NUMBER


TRANSMISSION NUMBER


ENGINE NUMBER


The Engine Number is stamped on the right front side of the engine block.


The Transmission Number appears on a label on the top edge of the transmission where it attaches to the engine.


Main Menust DOT Tire Quality Grades


The tires on your car meet Federal Safety Requirements. All tires are also "graded" according to Department of Transportation (DOT) standards for tread wear, traction and temperature.


Three grades are shown on the tire sidewall


TIRE


WHEEL RIM


Tread Wear The tread wear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one half (1-1/2) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices and differences in road characteristics and climate.


Traction The traction grades, from highest to lowest, are A, B, and C, and they represent the tire's ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance.


The traction grades assigned are based on braking (straight ahead) traction tests and do not include cornering (turning) traction.


Main Menust Temperature The temperature grades are A (the highest), B and C representing the tire's resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law.


The tire temperature grade is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.


Main Menust Emission Controls


Sources of Emissions The combustion process produces carbon monoxide, oxides of nitrogen and hydrocarbons. The evaporation of fuel in the fuel tank also produces hydrocarbons. Control of oxides of nitrogen and hydrocarbons is very important since, under certain conditions, when subjected to sunlight, they react to form photochemical smog. Carbon monoxide does not react to form smog, but it is toxic.


Honda Motor Co., Ltd. has developed a number of systems which are highly effective in reducing carbon monoxide, oxides of nitrogen and hydrocarbons.


The Clean Air Act The Clean Air Act requires all vehicle manufacturers to explain in writing, the operation and maintenance of their emission control systems. Maintenance instructions are included on pages 78 — 83 ; the operation of each system is explained on the following.


Replacement Parts The emission control systems on your new Honda were designed, built and certified the Federal regulations implementing the Clean Air Act, Honda recommends only the use of new, genuine Honda parts or their equivalent. The use of other replacement parts which are not of equivalent quality may impair the effectiveness of your car's emission control systems.


to conform with


Crankcase Emission Control System To prevent crankcase emissions, your car is equipped with a Positive Crankcase Ventilation (PCV) System which routes blowby gases from the crankcase, through the PCV valve and intake manifold, into the combustion chamber.


Main Menust Evaporative Emission Control System The Evaporative Emission Control System is designed to prevent fuel vapors from escaping into the atmosphere.


Fuel vapors from the fuel tank are directed into the charcoal canister where they are adsorbed and stored while the engine is stopped or idling. When the coolant temperature rises to a certain value, the vapors are drawn into the engine through the throttle body and the intake manifold during normal engine operation.


Engine Exhaust Controls The engine exhaust emission control systems are designed to control combustion during idle, acceleration, cruise, and deceleration. These systems are entirely separate from the crankcase and evaporative emission control systems described previously.


HONDA PGM-FI System The PGM-FI system consists of three independent sub-systems; Air Intake, Electronic Control and Fuel Control, thus allowing more accurate control of air/fuel ratios under all operating conditions. The Electronic Control Unit (ECU) detects the amount of air drawn into the cylinders and determines the amount of fuel to be injected to provide the optimum air/fuel ratio for all engine needs.


Ignition Timing Control System This system automatically controls the ignition timing to reduce the amount of HC and NOx,


Exhaust Gas Recirculation (EGR) The EGR system is designed to control the formation of oxides of nitrogen (NOx) caused when fuel mixture burns at high temperature. It works by recirculating exhaust gas through the EGR valve and intake manifold into the combustion chambers where it reduces peak temperature by diluting the air/fuel mixture.


Catalytic Converter The catalyst is used to convert hydrocarbons (HC), carbon monoxide (CO) and oxides of nitrogen (NOx) in the exhaust gas, to carbon dioxide (CO 2), dinitrogen (N 2) and water vapor.


Main Menust Catalytic Converter


A catalytic converter is installed in the exhaust system to help clean-up the harmful exhaust gases that can cause air pollution.


CATALYTIC CONVERTER


To be effective, the converter must work at high temperature, so don't park your car over dry grass, leaves or anything else that could burn easily. To stay effective, the converter must not be contaminated by leaded gasoline; use only unleaded gas as explained on page 57 .


CAUTION: The converter can be overheated and damaged if it's fed too much unburned fuel mixture from the engine, so:


— Don't push or tow the car to start it; if the battery is dead,


jump start the car as shown on page 123 .


—Don't turn the key off while the engine is running above idle


speed.


control parts.


—Don't change the ignition timing, or remove any emission


—Use only the spark plugs specified in this manual. —Don't keep driving your car if it isn't running properly, or if its CHARGE warning light somes on; have it checked by your Honda dealer.


Main Menust Warranty Service


Warranty The following warranties are provided with every new vehicle: 1. New Car Limited Warranty 2. Emission Control Systems Defects Warranty 3. Emission Performance Warranty 4. Original Equipment Battery Limited Warranty 5. Rust Perforation Limited Warranty 6. Accessory Limited Warranty 7. Replacement Parts Limited Warranty 8. Replacement Muffler Lifetime Limited Warranty 9. Seat Belt Limited Warranty 10. Replacement Battery Limited Warranty Your car's original tires are covered by their manufacturer. Tire warranty information is in a separate booklet. All warranty details pertaining to your car can be found in the Warranty booklet provided with your new car except the required maintenance schedule which is contained here in the Owner's Manual. If you are unable to obtain warranty service or are dissatisfied with the warranty decision or service you received at an authorized Honda dealership, you should review that dealership's Service Manager. This will normally resolve your problem. If it does not resolve your problem you should appeal the decision with the owner of the dealership. Please bear in mind that your problem will likely be resolved at the dealership, using the dealer's facilities, equipment and personnel. So it is very important that your initial contact be with the dealer or his management. After following these steps, if you wish to have the matter reviewed by American Honda you should contact the Zone Office serving your area, as shown on the map on the inside of the back cover. When contacting American Honda, please provide the Zone Office with the following information:


the matter with


Vehicle Identification Number Servicing Dealer Name and Address Date of Purchase Mileage on your Car Your Name, Address, and Phone Number Nature of Problem Selling Dealer


After a review of the facts, you will be advised of what can be done.


Main Menust Reporting Safety Defects


If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying American Honda Motor Co., Inc. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your dealer, or American Honda Motor Co., Inc. To contact NHTSA, you may either call the Auto Safety Hotline toll- free at 1-800-424-9393 (or 366-0123 in Washington, D.C. area) or write to: NHTSA, U.S. Department of Transportation Washington, D.C. 20590. You can also obtain other information about motor vehicle safety from the Hotline.


Main Menust Air Conditioner


Operation.................................... 45
Service ...................................... 111
Air Filter........................................... 97
Air Pressure, Tires ....................... 107
Aluminum Alloy Wheels............... 114
Antifreeze


..................See "Radiator coolant" Anti-lock Brake System................. 20


Anti-lock Brake System


Warning Light ........................ 26
Anti-lock Brake Fluid................. 101


Anti-theft Steering Column Lock


System.......................................... 60
Appearance Care .......................... 113
Ashtrays,......................................... 40
Audio System ................................. 49
Automatic Transmission


Driving Technique ....................... 70
Fluid .............................................. 89
Operation.,................................... 69
Shift Lever Position


Indicator.................................. 23


Battery


Charging System Warning


Light ......................................... 25
Jump Starting .........................123
Maintenance...............................102
Specification ...............................130


Beeper System


Fasten Seat Belt Beeper ............. 14
Key Reminder .............................. 60
Light Reminder Chime ................. 32


Belts,Seat ...............See "Seat Belts" Brake Lamp Warning Light ............. 27
Brakes


Anti-lock Brake System .............. 20
Anti-lock Brake System


Warning Light ......................... 26
Anti-lock Brake Fluid................. 101
Brake Failure Warning


Light ......................................... 25
Brake Fluid.................................. 101
Brake System Design ................ 100
Brake Wear ................................ 100
Brake Wear Indicators .............. 100
Parking Brake ................................ 41


Index


Parking Brake Warning


Light........................................25
Break-In Period ..................................2
Bulb


Replacement.............................105
Specification...............................130
Buzzer ............See "Beeper System"


Capacities......................................129
Care and Cleaning.........................113
Catalytic Converter .....................136
Certification Label ........................131
Chains,Tires..................................108
Child Restraint System ..................16
Cigarette Lighter............................40
Clock................................................39
COMPACT Spare Tire .................117
Coolant Temperature Gauge .........22
Cooling(with A/C) ...........................46
Cooling System...............................90
Crankcase Emission Control System ...........................................134
Cruise Control


Operation..................................37
Indicator.....................................24

Loading...
x