Canada
If the brake fluid level is at or below
the MIN mark on the side of the
brake fluid reservoir in the engine
compartment, you will see ‘‘BRAKE
FLUID LOW.’’ If you see this
message, have the brake system
checked by your dealer (see page
473
).
If the level of the fuel in the tank gets low, you will see ‘‘FUEL LOW’’ on the multi-information display, and you must refuel soon. The low fuel indicator on the instrument panel will also come on.
OnCanadianmodelonly If the fluid level in the windshield washer reservoir gets low, you will see ‘‘WASHER FLUID LOW’’ on the multi-information display.
CONTINUED
93
2008 Odyssey Table Of ContentsMain Menu07/09/03 20:17:01 31SHJ630 0099
Multi-Information Display
PassengerSideAirbagOff
CheckTirePressure
Warning:ApproachingObject
U.S.
Canada
If the passenger’s side airbag has automatically shut off, you will see ‘‘PASSENGER SIDE AIRBAG OFF’’ on the multi-information display. See page
for more information.
35
If one or more of your vehicle tires
are low on pressure, you will see a
‘‘CHECK TIRE PRESSURE’’
message on the display. See page
391
for more information on the tire
pressure monitoring system (TPMS).
This message, and the indicator to
the left of the message, is part of the
parking sensor system. If you are
approaching too close to an object,
you will see ‘‘WARNING:
APPROACHING OBJECT’’ on the
display and hear a beeper. See page
353
for more information.
94
2008 Odyssey Table Of ContentsMain Menu07/09/03 20:17:12 31SHJ630 0100
MaintenanceMessages
When the engine oil life reaches 15%, the display shows ‘‘SERVICE DUE SOON’’ and the code for the maintenance items to be performed.
When the engine oil life reaches 5%, the display shows ‘‘SERVICE DUE NOW’’ along with the same maintenance items.
Have your dealer do the indicated maintenance as soon as you see this message, and have them reset the display after completing the service.
If you do not perform the indicated maintenance or do not reset the display, the message changes to ‘‘SERVICE PAST DUE’’ when the engine oil life becomes 0%.
These messages appear on the multi- information display each time you turn the ignition switch to the ON (II) position.
For details on engine oil life and
maintenance messages, refer to page
409
Also refer to page maintenance safety precautions.
for important
406
Multi-Information Display
CheckTPMSSystem
If there is a problem in the tire pressure monitoring system (TPMS), you will see ‘‘CHECK TPMS SYSTEM’’ on the multi-information display. If you see this message, the TPMS is not monitoring tire pressures. Have the TPMS checked by your dealer as soon as possible (see page
395
).
CONTINUED
95
2008 Odyssey Table Of ContentsMain Menu07/09/03 20:17:20 31SHJ630 0101
Multi-Information Display
CheckVSASystem
CheckEngineOilLevel
CheckChargingSystem
If there is a problem with the vehicle stability assist (VSA) system, you will see ‘‘CHECK VSA SYSTEM’’ on the multi-information display. If you see this message, have the VSA system checked by your dealer (see page
386
).
If the engine oil is very low or has
lost pressure, you will see ‘‘CHECK
ENGINE OIL LEVEL’’ on the multi-
information display. You will also see
the low oil pressure indicator in the
instrument panel flashing or staying
on. If you see this message, you
should take immediate action since
serious engine damage is possible.
471
Follow the procedure on page
96
If you see ‘‘CHECK CHARGING SYSTEM’’ on the multi-information display, it means the battery is not being charged. See page more information.
471
for
2008 Odyssey Table Of ContentsMain Menu07/09/03 20:17:29 31SHJ630 0102
CheckEmissionSystem
CheckBrakeSystem
CheckTransmission
Multi-Information Display
If you see ‘‘CHECK EMISSION SYSTEM’’ on the multi-information display, it means one of the engine’s emission systems may have a problem. Have your vehicle checked by your dealer (see page
472
).
U.S.
Canada
If there is a problem with the brake system, you will see ‘‘CHECK BRAKE SYSTEM’’ on the multi- information display. The parking brake and brake system indicator in the instrument panel will also come on. See page information.
for more
473
If there is a problem with the automatic transmission, you will see ‘‘CHECK TRANSMISSION’’ on the multi-information display. Avoid rapid acceleration, and have the transmission checked by a dealer as soon as possible.
CONTINUED
97
2008 Odyssey Table Of ContentsMain Menu07/09/03 20:17:36 31SHJ630 0103
Multi-Information Display
CheckABSSystem
CheckAirbagSystem
CheckParkingSensorSystem
If there is a problem in the anti-lock brake system (ABS), you will see ‘‘CHECK ABS SYSTEM’’ on the multi-information display. If you see this message, have your vehicle checked by a dealer (see page
384
).
98
If there is a problem with your front airbags, side airbags, passenger’s side airbag automatic cutoff system, automatic seat belt tensioners, side curtain airbags, driver’s seat position sensor, or the front passenger’s weight sensors, you will see ‘‘CHECK AIRBAG SYSTEM’’ on the multi-information display. Take your vehicle to a dealer as soon as possible (see page
34
).
If there is a problem with the
parking sensor system, the multi-
information display shows a
‘‘CHECK PARKING SENSOR
SYSTEM’’ message. See page
354
for more information.
2008 Odyssey Table Of ContentsMain Menu07/09/03 20:17:46 31SHJ630 0104
CheckLeft/RightSlidingDoor
CheckPowerTailgate
CheckDRLSystem
U.S.
U.S.
Multi-Information Display
Canada
Canada
If there is a problem with either
power sliding door, the multi-
information display shows ‘‘CHECK
LEFT SLIDING DOOR’’ or ‘‘CHECK
RIGHT SLIDING DOOR.’’ See page
166
for more information.
If there is a problem with the power
tailgate, the display shows ‘‘CHECK
POWER TAILGATE.’’ See page
158
for more information.
If you see a ‘‘CHECK DRL SYSTEM’’ message on the multi- information display, there is a problem in the high beam headlight’s circuit. Take your vehicle to a dealer to have it checked.
CONTINUED
99
2008 Odyssey Table Of ContentsMain Menu07/09/03 20:17:52 31SHJ630 0105
Multi-Information Display
PAXWarningMessages
For more information, see page
454
U.S.models(Ifequipped) Your vehicle is equipped with the Michelin PAX system. The PAX system uses the multi-information display to show you one of three messages while you are driving with a flat tire.
100
2008 Odyssey Table Of ContentsMain Menu07/09/03 20:18:04 31SHJ630 0106
Customized Settings
With the ignition switch in the ON
(II) position, press and hold the
INFO button for more than 3
seconds. ‘‘CUSTOMIZE ENTRY’’
appears on the multi-information
display.
You can customize some vehicle control settings for ‘‘DRIVER 1’’ and ‘‘DRIVER 2’’ separately.
To have the driver’s ID detected, make sure you use your transmitter to unlock the driver’s door.
If you use the key to unlock the driver’s door, the system cannot recognize either ‘‘DRIVER 1’’ or ‘‘DRIVER 2.’’ In this case, when you try to enter the customizing mode, ‘‘DRIVER UNKNOWN CUSTOMIZE IMPOSSIBLE’’ will be displayed, and you cannot customize the settings.
You cannot customize the settings under these conditions:
If you turn the ignition switch to the ACCESSORY (I) or the LOCK (0) position.
If you move the shift lever out of Park.
You can cancel each custom setting (Driver 1, Driver 2). Press and hold the LOCK and SLIDING DOOR button (passenger’s side) at the same time until the LED in the remote transmitter will blink twice. At this time, the custom setting is changed to the default setting. To activate each custom setting (Driver 1, Driver 2), repeat this procedure. The LED will blink for 1 second to indicate the custom setting has been activated.
Multi-Information Display
The first customizing menu is:
CHANGE SETTING DEFAULT ALL
If you want to change any vehicle control settings, select ‘‘CHANGE SETTING,’’ and follow the instructions on page
106
If you want the settings as they were when the vehicle left the factory, select ‘‘DEFAULT ALL,’’ as described on page
104
Use the INFO button on the steering wheel to see the settings, and the SEL/RESET button to enter your selections.
Refer to the table on the following pages about the settings you want to customize.
CONTINUED
101
2008 Odyssey Table Of ContentsMain Menu07/09/03 20:18:09 31SHJ630 0107
Multi-Information Display
Group Setup METER SETUP (P. 107)
Menu Item
LANGUAGE SELECTION
Changes the language used in the display.
Description
Setting Option
ADJUST OUTSIDE TEMP. DISPLAY
Changes the outside temperature reading above or below its current reading.
TRIP A RESET WITH REFUEL ELAPSED TIME RESET
MEMORY POSITION LINK INTERIOR LIGHT DIMMING TIME
Causes trip meter A and the average fuel economy to reset when you refuel. Resets the elapsed time of your current trip.
Changes the driver’s seat to a stored setting.
Changes how long (in seconds) the interior lights stay on after you close the doors.
HEADLIGHT AUTO OFF TIMER
Changes how long (in seconds) the exterior lights stay on after you close the driver’s door.
POSITION SETUP (P. 116) LIGHTING SETUP (P. 118)
*
Default setting
102
Page
108
110
112
114
116
118
120
*
〜 〜 *
5F° (U.S.) 3C°
*
*
*
5F° 3C°
0°F 0°C
ENGLISH FRENCH SPANISH − 〜± − 〜± (Canada) ON OFF IGN RESET TRIP A RESET TRIP B RESET ON OFF 15 sec 30 sec 60 sec 0 sec 15 sec 30 sec 60 sec
*
*
*
2008 Odyssey Table Of ContentsMain Menu07/11/15 08:54:42 31SHJ630 0108
Multi-Information Display
Group Setup
DOOR · WINDOW SETUP (P. 122)
Menu Item
Description
AUTO DOOR LOCK
Changes when the doors automatically lock.
AUTO DOOR UNLOCK
Changes when the doors automatically unlock.
KEYLESS LOCK ACKNOWLEDGEMENT
SECURITY RELOCK TIMER
FRONT WIPER ACTION
The exterior lights flash each time you press the LOCK or UNLOCK button. A beeper will also sound when you press the LOCK button twice. Changes how long it takes (in seconds) for the doors to relock and the security system to set after you unlock and do not open the door. Changes the wiper operation between two settings when the wiper switch is in the INT position. Changes all the customized settings as they were when the vehicle left the factory.
WIPER SETUP (P. 131) DEFAULT ALL
*
Default setting
Setting Option
*
*
SHIFT FROM P WITH VEHICLE SPEED OFF DRIVER’S DOOR WITH SHIFT TO P ALL DOORS WITH SHIFT TO P DRIVER’S DOOR WITH IGN OFF ALL DOORS WITH IGN OFF OFF ON OFF
*
*
30 sec 60 sec 90 sec WITH VEH SPD INTERMITTENT OK CANCEL
*
Page
123
125
127
129
131
104
103
2008 Odyssey Table Of ContentsMain Menu07/09/03 20:18:21 31SHJ630 0109
Multi-Information Display
DEFAULT ALL
To set the default settings, select ‘‘OK’’ by pressing the INFO button, then press the SEL/RESET button.
When ‘‘DEFAULT ALL’’ is completed successfully, you will see the above display for several seconds, and the display will return to ‘‘CUSTOMIZE ENTRY.’’
To enter the customizing mode, press and hold the INFO button for more than 3 seconds. Then select ‘‘DEFAULT ALL’’ by pressing the INFO button.
Press the SEL/RESET button to enter ‘‘DEFAULT ALL.’’
104
2008 Odyssey Table Of ContentsMain Menu07/09/03 20:18:26 31SHJ630 0110
Multi-Information Display
If ‘‘DEFAULT ALL’’ is not completed successfully, you will see the above display for several seconds, then the display goes back to the normal message mode. Repeat the procedure to select ‘‘DEFAULT ALL.’’
If you want to cancel ‘‘DEFAULT ALL,’’ select ‘‘CANCEL,’’ then press the SEL/RESET button. The display goes back to ‘‘CUSTOMIZE ENTRY.’’
105
2008 Odyssey Table Of ContentsMain Menu07/09/03 20:18:35 31SHJ630 0111
Multi-Information Display
Change Setting You can customize some of the vehicle control settings to your preference. Here are the settings you can customize:
METER SETUP (see page
107
POSITION SETUP (see page
116
LIGHTING SETUP (see page
118
DOOR · WINDOW SETUP (see
page
WIPER SETUP (see page
122
131
While the multi-information display is showing ‘‘CHANGE SETTING,’’ press the SEL/RESET button. The display will change to the initial display of CUSTOMIZE GROUP. Then, each time you press the INFO button, the display changes as shown in the next column. Press the INFO button until you see the setup you want to customize, and press the SEL/RESET button to enter your selection.
106
Press the SEL/RESET button
Press the INFO button
2008 Odyssey Table Of ContentsMain Menu07/09/03 20:18:44 31SHJ630 0112
Meter Setup There are four custom settings items in the Meter Setup:
Press the INFO button
Multi-Information Display
108
LANGUAGE SELECTION (see page ADJUST OUTSIDE TEMP. DISPLAY (see page TRIP A RESET WITH REFUEL (see page ELAPSED TIME RESET (see page
110
112
114
While ‘‘METER SETUP’’ is displayed, press the SEL/RESET button on the steering wheel. Then, press the INFO button repeatedly. Each time you press the INFO button, the display changes as shown. To customize a setting, press the INFO button repeatedly until you see the setting, and press the SEL/ RESET button. Then, follow the procedures described on the following pages.
CONTINUED
107
2008 Odyssey Table Of ContentsMain Menu07/09/03 20:18:50 31SHJ630 0113
Multi-Information Display
LanguageSelection
While the multi-information display is showing ‘‘METER SETUP,’’ press the SEL/RESET button on the steering wheel. The display changes to ‘‘LANGUAGE SELECTION.’’ Press the SEL/RESET button again to enter the language selection mode.
There are three selectable languages, English, French, and Spanish. Each time you press the INFO button, the display changes as shown.
Select the language you want by pressing the INFO button, and press the SEL/RESET button to enter your selection.
108
2008 Odyssey Table Of ContentsMain Menu07/09/03 20:18:58 31SHJ630 0114
Multi-Information Display
When language selection is successfully completed, the display changes to the screen shown above for several seconds, then goes back to ‘‘CUSTOMIZE MENU.’’
If you fail to select a language properly, you will see the above display for several seconds, then the display goes back to ‘‘CUSTOMIZE MENU.’’ Repeat the setup.
To exit ‘‘LANGUAGE SELECTION,’’ press the INFO button repeatedly until you see ‘‘EXIT,’’ then press the SEL/RESET button. The display goes back to ‘‘CUSTOMIZE MENU.’’
All messages on the multi- information display will be shown in the language you selected.
CONTINUED
109
2008 Odyssey Table Of ContentsMain Menu07/09/03 20:19:03 31SHJ630 0115
Multi-Information Display
AdjustOutsideTemp.Display If you find that the temperature reading is always a few degrees below or above the actual temperature, adjust it as described on the following columns.
While the multi-information display shows ‘‘METER SETUP,’’ press the SEL/RESET button on the steering wheel. The display changes to the ‘‘CUSTOMIZE MENU.’’ Press the INFO button once, and you will see ‘‘ADJ. OUTSIDE TEMP. DISPLAY’’ as shown above.
Press the SEL/RESET button. The display changes as shown above. The highlighted number is the current adjustment above or below the outside temperature. Press the INFO button repeatedly until the appropriate number appears, then press the SEL/RESET button to enter your selection.
110
2008 Odyssey Table Of ContentsMain Menu07/09/03 20:19:10 31SHJ630 0116
Multi-Information Display
When your selection is successfully entered, you will see the above display for several seconds, and then the display changes back to ‘‘CUSTOMIZE MENU.’’
If you fail to enter the desired adjustment properly, you will see the above display for several seconds, then the display goes back to ‘‘CUSTOMIZE MENU.’’ Repeat the adjustment.
To exit ‘‘ADJ. OUTSIDE TEMP. DISPLAY,’’ press the INFO button until you see ‘‘EXIT,’’ and press the SEL/RESET button. The display goes back to ‘‘CUSTOMIZE MENU.’’
CONTINUED
111
2008 Odyssey Table Of ContentsMain Menu07/09/03 20:19:16 31SHJ630 0117
Multi-Information Display
TripAResetwithRefuel To cause ‘‘Trip meter A’’ and ‘‘Average Fuel Economy’’ to reset every time you refuel your vehicle, adjust it as described on the following pages.
While the multi-information display shows ‘‘METER SETUP’’ of the ‘‘CUSTOMIZE GROUP,’’ press the SEL/RESET button on the steering wheel. The display changes to ‘‘CUSTOMIZE MENU.’’ Press the INFO button repeatedly until you see ‘‘TRIP A RESET WITH REFUEL.’’ in the lower segment as shown above.
Press the SEL/RESET button. The display changes as shown above. The lower segment changes between ‘‘ON’’ and ‘‘OFF’’ each time you press the INFO button. Enter your selection by pressing the SEL/ RESET button.
112
2008 Odyssey Table Of ContentsMain Menu07/09/03 20:19:22 31SHJ630 0118
Multi-Information Display
When your selection is successfully entered, you will see the above display for several seconds, and then the display goes back to ‘‘CUSTOMIZE MENU.’’
If you fail to enter your selection, you will see the above display for several seconds, then the display goes back to ‘‘CUSTOMIZE MENU.’’ Repeat the setup.
To exit ‘‘TRIP A RESET WITH REFUEL,’’ press the INFO button until you see ‘‘EXIT,’’ and press the SEL/RESET button. The display goes back to ‘‘CUSTOMIZE MENU.’’
CONTINUED
113
2008 Odyssey Table Of ContentsMain Menu07/09/03 20:19:30 31SHJ630 0119
Multi-Information Display
ElapsedTimeReset There are three possible settings:
IGN RESET: The elapsed time resets each time the ignition switch is turned to the ON (II) position.
TRIP A RESET: The elapsed time resets each time the TRIP A is reset.
TRIP B RESET: The elapsed time resets each time the TRIP B is reset.
While the multi-information display shows ‘‘METER SETUP’’ of the ‘‘CUSTOMIZE GROUP,’’ press the SEL/RESET button on the steering wheel. The display changes to ‘‘CUSTOMIZE MENU.’’ Press the INFO button repeatedly until you see ‘‘ELAPSED TIME RESET’’ in the lower segment as shown above.
Press the SEL/RESET button. The display changes as shown above.
Press the INFO button repeatedly until the desired condition appears, then press the SEL/RESET button to enter your selection.
114
2008 Odyssey Table Of ContentsMain Menu07/09/03 20:19:37 31SHJ630 0120
Multi-Information Display
When your selection is entered, you will see the above display for several seconds, and the display goes back to ‘‘CUSTOMIZE MENU.’’
If you fail to enter your selection, you will see the above display for several seconds, and the display goes back to ‘‘CUSTOMIZE MENU.’’ Repeat the setup.
To exit ‘‘ELAPSED TIME RESET,’’ press the INFO button until you see ‘‘EXIT,’’ then press the SEL/RESET button.
115
2008 Odyssey Table Of ContentsMain Menu07/09/03 20:19:44 31SHJ630 0121
Multi-Information Display
Position Setup If ‘‘MEMORY POSITION LINK’’ is ‘‘ON,’’ the driver’s seat and outside mirrors move to the positions stored in the memory when you open the driver’s door, using the remote transmitter.
MemoryPositionSetup
184
Refer to page
for setting the seat
position memory. Also refer to page
149
for remote transmitter use.
While the multi-information display shows ‘‘POSITION SETUP,’’ press the SEL/RESET button on the steering wheel. The display changes to ‘‘MEMORY POSITION LINK’’ as shown above.
Press the SEL/RESET button. The display changes as shown above.
Select ‘‘ON’’ or ‘‘OFF’’ by pressing the INFO button, and enter your selection by pressing the SEL/ RESET button.
116
2008 Odyssey Table Of ContentsMain Menu07/09/03 20:19:50 31SHJ630 0122
Multi-Information Display
When your selection is entered, you will see the above display for several seconds, then the display goes back to ‘‘CUSTOMIZE MENU.’’
If you fail to enter your selection, you will see the above display for several seconds, and the display goes back to ‘‘CUSTOMIZE MENU.’’ Repeat the setup.
To exit ‘‘MEMORY POSITION LINK,’’ press the INFO button until you see ‘‘EXIT,’’ then press the SEL/ RESET button.
117
2008 Odyssey Table Of ContentsMain Menu07/09/03 20:19:59 31SHJ630 0123
Multi-Information Display
Lighting Setup There are two custom settings in the Lighting Setup:
InteriorLightDimmingTime
INTERIOR LIGHT DIMMING TIME (see next column) HEADLIGHT AUTO OFF TIMER (see page
120
While the ‘‘LIGHTING SETUP’’ is displayed, press the SEL/RESET button on the steering wheel. Each time you press the INFO button, the display changes between ‘‘INTERIOR LIGHT DIMMING TIME’’ and ‘‘HEADLIGHT AUTO OFF TIMER.’’ To make your selection, press the SEL/RESET button.
118
The interior lights fade out when you close all doors. You can change the time that the interior lights fade out.
While the multi-information display shows ‘‘LIGHTING SETUP,’’ press the SEL/RESET button on the steering wheel. The display changes to ‘‘INTERIOR LIGHT DIMMING TIME’’ as shown above.
Press the SEL/RESET button. The display changes as shown above.
Each time you press the INFO button, the highlighted number changes from ‘‘15 sec,’’ to ‘‘30 sec,’’ and then to ‘‘60 sec.’’ To make your selection, press the SEL/RESET button.
2008 Odyssey Table Of ContentsMain Menu07/09/03 20:20:05 31SHJ630 0124
Multi-Information Display
When your selection is entered, you will see the above display for several seconds, and then the display goes back to ‘‘CUSTOMIZE MENU.’’
If you fail to enter your selection, you will see the above display for several seconds, and the display goes back to ‘‘CUSTOMIZE MENU.’’ Repeat the setup.
To exit ‘‘INTERIOR LIGHT DIMMING TIME,’’ press the INFO button until you see ‘‘EXIT,’’ then press the SEL/RESET button.
119
2008 Odyssey Table Of ContentsMain Menu07/09/03 20:20:12 31SHJ630 0125
Multi-Information Display
HeadlightAutoOffTimer The headlights, parking lights, taillights, and license plate light turn off after the selected time when you remove the key from the ignition switch and close the driver’s door.
While the multi-information display shows ‘‘LIGHTING SETUP,’’ press the SEL/RESET button on the steering wheel. Then press the INFO button to display ‘‘HEADLIGHT AUTO OFF TIMER’’ as shown above.
Press the SEL/RESET button. The display changes as shown above.
Each time you press the INFO button, the highlighted number changes from ‘‘0 sec,’’ to ‘‘15 sec,’’ to ‘‘30 sec,’’ and then to ‘‘60 sec.’’ Press the INFO button repeatedly until the desired time appears, then press the SEL/RESET button to enter your selection.
120
2008 Odyssey Table Of ContentsMain Menu07/09/03 20:20:18 31SHJ630 0126
Multi-Information Display
When your selection is entered, you will see the above display for several seconds, and then the display goes back to ‘‘CUSTOMIZE MENU.’’
If you fail to enter your selection, you will see the above display for several seconds, and the display goes back ‘‘CUSTOMIZE MENU.’’ Repeat the setup.
To exit ‘‘HEADLIGHT AUTO OFF TIMER,’’ press the INFO button until you see ‘‘EXIT,’’ then press the SEL/RESET button.
121
2008 Odyssey Table Of ContentsMain Menu07/09/03 20:20:27 31SHJ630 0127
Multi-Information Display
Door · Window Setup There are three custom settings in the Door · Window Setup:
125
AUTO DOOR LOCK (see page
123
AUTO DOOR UNLOCK (see
page
KEYLESS LOCK
ACKNOWLEDGEMENT (see
page
SECURITY RELOCK TIMER (see
page
127
129
While the multi-information display shows ‘‘DOOR · WINDOW SETUP,’’ press the SEL/RESET button on the steering wheel. Each time you press the INFO button, the display changes as shown in the next column. To customize a setting, press the INFO button repeatedly until you see the setting you want to customize, and press the SEL/RESET button. Then follow the procedures described on the following pages.
122
Press the INFO button
2008 Odyssey Table Of ContentsMain Menu07/09/03 20:20:35 31SHJ630 0128
Multi-Information Display
AutoDoorLock There are three settings you can choose from:
−
OFF The auto door lock is deactivated all the time.
VEHICLE SPEED The doors lock
when the vehicle speed reaches 9
mph (15 km/h).
−
SHIFT FROM P The doors lock whenever you move the shift lever out of Park.
−
While the multi-information display shows ‘‘DOOR · WINDOW SETUP’’ press the SEL/RESET button on the steering wheel. The display changes to ‘‘AUTO DOOR LOCK’’ as shown above.
Press the SEL/RESET button. The display changes as shown above.
Press the INFO button repeatedly until the desired condition appears, then press the SEL/RESET button to enter your selection.
CONTINUED
123
2008 Odyssey Table Of ContentsMain Menu07/09/03 20:20:41 31SHJ630 0129
Multi-Information Display
When your selection is entered, you will see the above display for several seconds, and then the display goes back to ‘‘CUSTOMIZE MENU.’’
If you fail to enter your selection, you will see the above display for several seconds, and the display goes back to ‘‘CUSTOMIZE MENU.’’ Repeat the setup.
To exit ‘‘AUTO DOOR LOCK,’’ press the INFO button until you see ‘‘EXIT,’’ then press the SEL/RESET button.
124
2008 Odyssey Table Of ContentsMain Menu07/09/03 20:20:49 31SHJ630 0130
Multi-Information Display
AutoDoorUnlock There are three settings you can choose from:
−
SHIFT TO P The driver’s door or all the doors unlock when you move the shift lever to Park.
−
IGN OFF The driver’s door or all the doors unlock when you turn the ignition switch to the LOCK (0) position.
−
OFF deactivated all the time.
The auto door unlock is
While the multi-information display shows ‘‘DOOR·WINDOW SETUP,’’ press the SEL/RESET button on the steering wheel. Then press the INFO button once. The display changes to ‘‘AUTO DOOR UNLOCK’’ as shown above.
Press the SEL/RESET button. The display changes as shown above.
Press the INFO button repeatedly until the desired condition appears, and press the SEL/RESET button to enter your selection.
CONTINUED
125
2008 Odyssey Table Of ContentsMain Menu07/09/03 20:20:55 31SHJ630 0131
Multi-Information Display
When your selection is entered, you will see the above display for several seconds, and then the display goes back to ‘‘CUSTOMIZE MENU.’’
If you fail to enter your selection, you will see the above display for several seconds, and the display goes back to ‘‘CUSTOMIZE MENU.’’ Repeat the setup.
To exit ‘‘AUTO DOOR UNLOCK,’’ press the INFO button until you see ‘‘EXIT,’’ then press the SEL/RESET button.
126
2008 Odyssey Table Of ContentsMain Menu07/09/03 20:21:04 31SHJ630 0132
Multi-Information Display
KeylessLockAcknowledgement When you press the UNLOCK button on the remote transmitter to unlock the doors and the tailgate, the exterior lights blink twice to verify that the doors and the tailgate are unlocked and the security system is turned off.
When you push the LOCK button on the remote transmitter, some exterior lights flash, and a beeper sounds when you push the LOCK button again within 5 seconds to verify that the doors and the tailgate are locked and the security system has set (see page customize the exterior lights not to flash and the beeper not to sound.
). You can
318
While the multi-information display shows ‘‘DOOR·WINDOW SETUP,’’ press the SEL/RESET button on the steering wheel. Then press the INFO button repeatedly until you see ‘‘KEYLESS LOCK ACKNOWLEDGEMENT’’ as shown above.
Press the SEL/RESET button. The display changes as shown above.
Each time you press the INFO button, the display changes to ‘‘ON,’’ to ‘‘OFF,’’ then to ‘‘EXIT.’’
Select ‘‘ON’’ or ‘‘OFF’’ by pressing the INFO button, and enter your selection by pressing the SEL/ RESET button.
CONTINUED
127
2008 Odyssey Table Of ContentsMain Menu07/09/03 20:21:09 31SHJ630 0133
Multi-Information Display
When your selection is entered, you will see the above display for several seconds, and then the display changes to ‘‘CUSTOMIZE MENU.’’
If you fail to enter your selection, you will see the above display for several seconds, and the display goes back to ‘‘CUSTOMIZE MENU.’’ Repeat the setup.
To exit ‘‘KEYLESS LOCK ACKNOWLEDGEMENT,’’ press the INFO button until you see ‘‘EXIT,’’ then press the SEL/RESET button.
128
2008 Odyssey Table Of ContentsMain Menu07/09/03 20:21:17 31SHJ630 0134
Multi-Information Display
SecurityRelockTimer If you unlock the doors and the tailgate with the remote transmitter, but do not open any of the doors or the tailgate within 30 seconds, the doors and the tailgate automatically relock and the security system sets.
You can change this relock time from 30 seconds to 60 or 90 seconds.
While the multi-information display shows ‘‘DOOR·WINDOW SETUP,’’ press the SEL/RESET button on the steering wheel. Then press the INFO button repeatedly until you see ‘‘SECURITY RELOCK TIMER’’ as shown above.
Press the SEL/RESET button, then press the INFO button.
Select the desired relock time by pressing the INFO button, and enter your selection by pressing the SEL/ RESET button.
CONTINUED
129
2008 Odyssey Table Of ContentsMain Menu07/09/03 20:21:23 31SHJ630 0135
Multi-Information Display
When your selection is entered, you will see the above display for several seconds, and then the display goes back to ‘‘CUSTOMIZE MENU.’’
If you fail to enter your selection, you will see the above display for several seconds, and the display goes back to ‘‘CUSTOMIZE MENU.’’ Repeat the setup.
To exit ‘‘SECURITY RELOCK TIMER,’’ press the INFO button until you see ‘‘EXIT,’’ then press the SEL/RESET button.
130
2008 Odyssey Table Of ContentsMain Menu07/09/03 20:21:31 31SHJ630 0136
FrontWiperAction
Wiper Setup You can select from these two settings when the wiper switch is in the INT (intermittent) position:
WITH VEH SPD The intermittent operation varies according to vehicle speed.
−
Multi-Information Display
−
The
INTERMITTENT intermittent operation varies according to the selection you make on the wiper lever’s intermittent control ring.
With ‘‘WIPER SETUP’’ shown on the multi-information display, press the SEL/RESET button on the steering wheel. The display changes to ‘‘FRONT WIPER ACTION’’ as shown above.
Press the SEL/RESET button. The display changes as shown above.
Press the INFO button to select ‘‘WITH VEH SPD’’ or ‘‘INTERMITTENT,’’ and enter your selection by pressing the SEL/ RESET button.
CONTINUED
131
2008 Odyssey Table Of ContentsMain Menu07/09/03 20:21:37 31SHJ630 0137
Multi-Information Display
When your selection is entered, you will see the above display for several seconds, and then the display goes back to ‘‘CUSTOMIZE MENU.’’
If you fail to enter your selection, you will see the above display for several seconds, and the display goes back to ‘‘CUSTOMIZE MENU.’’ Repeat the setup.
To exit ‘‘FRONT WIPER ACTION,’’ press the INFO button until you see ‘‘EXIT,’’ then press the SEL/RESET button.
132
2008 Odyssey Table Of ContentsMain Menu07/09/03 20:21:46 31SHJ630 0138
Controls Near the Steering Wheel
HEADLIGHTS/TURN SIGNAL/ FOG LIGHTS
(P.135, 138)
WINDSHIELD WIPERS/WASHERS REAR WINDOW WIPER/WASHER
(P.134) (P.135)
PEDAL POSITION ADJUSTMENT SWITCH (P.193)
POWER SLIDING DOOR SWITCH
(P.162)
MOONROOF SWITCH (P.189)
REMOTE AUDIO CONTROL BUTTONS (P.282) POWER TAILGATE SWITCH VEHICLE STABILITY ASSIST (VSA) OFF SWITCH
(P.158)/
(P.387)
PARKING SENSOR SYSTEM SWITCH (P.352)
VEHICLE STABILITY ASSIST (VSA) OFF SWITCH
(P.387)
NAVIGATION SYSTEM BUTTONS
*
HORN
*
BLUETOOTH HANDSFREELINK BUTTONS(P.326)
STEERING WHEEL ADJUSTMENT (P.141)
LIGHT CONTROL SWITCH
(P.205)
MULTI-INFORMATION BUTTONS
(P.82)
CRUISE CONTROL BUTTONS (P.319)
CLOCK (P.281)
PASSENGER AIRBAG OFF INDICATOR (P.35)
HAZARD WARNING BUTTON (P.140)
AUDIO SYSTEM/ REAR ENTERTAINMENT SYSTEM (P.221, 285)
REAR WINDOW DEFOGGER BUTTON (P.140)
* *
1: 2:
To use the horn, press the center pad of the steering wheel. Only on vehicles equipped with navigation system. Refer to the navigation system manual.
133
2008 Odyssey Table Of ContentsMain Menu07/09/03 20:21:55 31SHJ630 0139
Windshield Wipers and Washers
MIST The wipers run at high speed until you release the lever.
−
OFF
−
The wipers are not activated.
−
INT The length of the wipe interval is varied automatically according to vehicle’s speed.
Vary the delay by turning the adjustment ring. If you turn it to the shortest delay ( position), the wipers change to low speed operation when the vehicle speed exceeds 12 mph (20 km/h).
LO
−
The wipers run at low speed.
HI
−
The wipers run at high speed.
ADJUSTMENT RING
1. 2. 3. 4. 5. 6.
MIST OFF INT LO Low speed HI High speed Windshield washers
Intermittent
− − −
Push the right lever up or down to select a position.
134
−
Pull the
Windshield Washer wiper control lever toward you, and hold it. The washers spray until you release the lever. The wipers run at low speed, then complete one more sweep after you release the lever.
OnTouringmodels You can customize some windshield wiper settings. See page more information.
131
for
2008 Odyssey Table Of ContentsMain Menu07/09/03 20:22:07 31SHJ630 0140
Windshield Wipers and Washers, Turn Signal and Headlights
Rear Window Wiper and Washer
Turn Signal and Headlights
When you shift the transmission to the reverse position with the front windshield wipers activated, the rear window wiper operates automatically.
When the wiper control lever is positioned as follows:
−
INT operates intermittently.
The rear window wiper
LO or HI operates continuously.
−
The rear window wiper
1.
2.
3. 4.
To turn on the rear window wiper, rotate the switch clockwise to ON. It operates intermittently. Hold past ON to turn the window wiper on and the window washer on. OFF Rotate the switch counterclockwise to spray the window washer.
1. 2. 3. 4. 5. 6. 7. 8.
9.
Turn signal Off Parking and indicator lights AUTO (Touring models only) Headlights on High beams Flash high beams Fog lights off (Touring models only) Fog lights on (Touring models only)
135
2008 Odyssey Table Of ContentsMain Menu07/09/03 20:22:13 31SHJ630 0141
Turn Signal, Headlights
−
Turn Signal Push down on the lever to signal a left turn and up to signal a right turn. To signal a lane change, push lightly on the lever, and hold it. The lever will return to center when you release it or complete a turn.
−
Headlights The rotating switch on the left lever controls the lights. Turning this switch to the ‘‘ ’’ position turns on the parking lights, taillights, instrument panel lights, side-marker lights, and rear license plate lights.
Turning the switch to the ‘‘ position turns on the headlights.
’’
’’ or ‘‘
When the light switch is in the ‘‘ ’’ position, the lights on indicator comes on as a reminder. This indicator stays on if you leave the light switch on and turn the ignition switch to the ACCESSORY (I) or the LOCK (0) position.
136
If you leave the lights on with the key removed from the ignition switch, you will hear a reminder chime when you open the driver’s door.
−
High Beams To switch from low beams to high beams, push the left lever forward until you hear a click. The high beam indicator will come on (see page ). Pull it back to return to low beams. To flash the high beams, pull the lever back lightly, then release it. The high beams will stay on as long as you hold the lever back.
73
2008 Odyssey Table Of ContentsMain Menu07/09/03 20:22:19 31SHJ630 0142
OnTouringmodels AUTO − The automatic lighting feature turns on the headlights, all other exterior lights, and the instrument panel lights when it senses low ambient light.