2004 Honda CR V Owners Manual

doorjamb.

Operate your vehicle on reasonable roads within the legal speed limit.

Drive your vehicle regularly over a distance of several miles (kilometers).

Always use unleaded gasoline with the proper octane rating (see page 124

).

Which Schedule to Follow: Service your vehicle according to the time and mileage periods on one of the Maintenance Schedules on the following pages.

−

Follow the

U.S. Owners Maintenance Schedule for Severe Conditions if you drive your vehicle MAINLY under one or more of the following conditions.

Driving less than 5 miles (8 km) per trip or, in freezing temperatures, driving less than 10
miles (16 km) per trip.

Driving in extremely hot [over 90°F (32°C)] conditions.

Used primarily as a delivery vehicle or taxi that is driven mostly in stop-and-go traffic and/ or parked with the engine idling.

Maintenance

165

０３／０７／１５　１２：１７：１７　３１Ｓ９Ａ６２０　０１７１　

Servicing Your Vehicle Your authorized Honda dealer knows your vehicle best and can provide competent, efficient service. However, service at a dealer is not mandatory to keep your warranties in effect. Maintenance may be done by any qualified service facility or skilled person to keep all the receipts as proof of completion, and have the person who does the work fill out the Maintenance Record. Check your warranty booklet for more information.

We recommend the use of Honda parts and fluids whenever you have maintenance done.

U.S. Vehicles: Maintenance, replacement, or repair of emissions control devices and systems may be done by any automotive repair establishment or individual using parts that are ‘‘certified’’ to EPA standards.

＃

According to state and federal regulations, failure to perform maintenance on the items marked with will not void your emissions warranties. However, Honda recommends that all maintenance services be performed at the recommended time or mileage period to ensure long-term reliability.

Maintenance Schedule

Trailer towing, driving with a roof top carrier, or driving in mountainous conditions.

Driving on muddy, dusty, or de- iced roads.

If you only OCCASIONALLY NOTE: drive under ‘‘severe’’ conditions, you should follow the Maintenance Schedule for Normal Conditions.

Canadian Owners Follow the Maintenance Schedule for Severe Conditions.

−

166

Maintenance

０３／０７／１５　１２：１７：２６　３１Ｓ９Ａ６２０　０１７２　

Maintenance Schedule

Owner’s Maintenance Checks You should check the following items at the specified intervals. If you are unsure of how to perform any check, turn to the appropriate page listed.

Engine oil level time you fill the fuel tank. See page

Check every

127

−

Engine coolant level radiator reserve tank every time you fill the fuel tank. See page

Check the

128

−

−

Windshield washer fluid Check the level in the reservoir monthly. If weather conditions cause you to use the washers frequently, check the reservoir each time you stop for fuel. See page

178

Automatic transmission Check the fluid level monthly. See page 179

−

Brakes monthly. See page

−

Check the fluid level

181

−

Tires Check the tire pressure monthly. Examine the tread for wear and foreign objects. See page 190

−

Check the operation of

Lights the headlights, parking lights, taillights, high-mount brake light, turn signals, brake lights, and license plate light monthly. See page

183

Maintenance

167

Follow the Normal Maintenance Schedule if the severe driving conditions specified in the Severe Conditions Maintenance Schedule on the next page do not apply.

NOTE: If you only OCCASIONALLY drive under ‘‘severe’’ conditions, you should follow the Normal Conditions Maintenance Schedule.

０３／０７／１５　１２：１７：５１　３１Ｓ９Ａ６２０　０１７３　

Service the items listed at the indicated distance (or time, if given). 90
144

miles x 1,000
km x 1,000

70
112

10
16

20
32

30
48

50
80

40
120
64
192
Check oil and coolant at each fuel stop

110
176

100
160

80
128

60
96

130
208

140
224

150
240

Check engine oil and coolant Check tires Replace engine oil

Rotate tires (follow pattern on page 193 ) Replace engine oil filter Check front and rear brakes Check parking brake adjustment Inspect the following items:

Tie-rod ends, steering gearbox, and boots Suspension components Driveshaft boots Brake hoses and lines (including ABS) All fluid levels and condition of fluids Exhaust system ＃ Fuel lines and connections

＃

Inspect drive belts Replace dust and pollen filter Replace air cleaner element Replace spark plugs Inspect valve clearance

Replace automatic transmission fluid ＊ Replace manual transmission fluid

Replace rear differential fluid

Inspect idle speed Replace engine coolant

Check inflation and condition once a month

((OOrreevveerryy11yyeeaarr,,wwhhiicchheevveerrccoommeessffiirrsstt))

Every 10,000 miles (16,000 km)

((OOrreevveerryy11yyeeaarr,,wwhhiicchheevveerrccoommeessffiirrsstt))

((OOrreevveerryy22yyeeaarrss,,wwhhiicchheevveerrccoommeessffiirrsstt))

((OOtthheerrwwiisseeaaddjjuussttoonnllyyiiffnnooiissyy))

((OOrreevveerryy66yyeeaarrss,,wwhhiicchheevveerrccoommeessffiirrsstt))

((OOrreevveerryy55yyeeaarrss,,wwhhiicchheevveerrccoommeessffiirrsstt))

Every 160,000 miles (256,000 km)

At 120,000 miles (192,000 km) or 10 years, then

every 60,000 miles (96,000 km) or 5 years Every 3 years (independent of mileage)

Replace at 120,000 miles (192,000 km) or 6 years, then every 90,000 miles (144,000 km) or 5 years. See information on maintenance and emission warranty on page

166

Replace brake fluid 1: ＊ ＃ 168

Maintenance

０３／０７／１５　１２：１８：２２　３１Ｓ９Ａ６２０　０１７４　

Service the items listed at the indicated distance (or time, if given). 90
144

miles x 1,000
km x 1,000

70
112

10
16

20
32

30
48

60
96

50
80

40
120
64
192
Check oil and coolant at each fuel stop

80
128

100
160

110
176

130
208

140
224

150
240

Check inflation and condition once a month

Every 5,000 miles (8,000 km) or every 6 months,

whichever comes first

Every 10,000 miles (16,000 km)

((OOrreevveerryy11yyeeaarr,,wwhhiicchheevveerrccoommeessffiirrsstt))

((OOrreevveerryy11yyeeaarr,,wwhhiicchheevveerrccoommeessffiirrsstt))

Inspect drive belts Replace dust and pollen filter Clean and replace air cleaner element ＊

＊

Clean every 15,000 miles (24,000 km), and replace every 30,000

((OOrreevveerryy22yyeeaarrss,,wwhhiicchheevveerrccoommeessffiirrsstt))

miles (48,000 km)

Check engine oil and coolant Check tires Replace engine oil

Rotate tires (follow pattern on page 193 ) Replace engine oil filter Check front and rear brakes Lubricate all hinges, locks and latches Inspect the following items:

Tie rod ends, steering gear box, and boots Suspension components, Driveshaft boots

Check parking brake adjustment Inspect the following items:

Brake hoses and lines (including ABS) All fluid levels and condition of fluids Exhaust system , Fuel lines and connections Lights and controls/vehicle underbody

＃

＃

Replace spark plugs Inspect valve clearance

Replace automatic transmission fluid ＊ Replace manual transmission fluid

Replace rear differential fluid

Inspect idle speed Replace engine coolant

Replace brake fluid

((OOtthheerrwwiisseeaaddjjuussttoonnllyyiiffnnooiissyy))

((OOrreevveerryy33yyeeaarrss,,wwhhiicchheevveerrccoommeessffiirrsstt))

((OOrreevveerryy44yyeeaarrss,,wwhhiicchheevveerrccoommeessffiirrsstt))

Every 160,000 miles (256,000 km)

At 120,000 miles (192,000 km) or 10 years, then

every 60,000 miles (96,000 km) or 5 years Every 3 years (independent of mileage)

＊

2 :

＊

3 :

＃

Follow the Severe Maintenance Schedule if you drive your vehicle MAINLY under one or more of the following conditions:

Driving less than 5 miles (8 km) per trip or, in freezing temperatures, driving less than 10 miles (16 km) per trip. Driving in extremely hot [over 90°F (32°C)] conditions. Extensive idling or long periods of stop and go driving, such as a taxi or Trailer towing, driving with a roof rack, or driving in mountainous conditions. Driving on muddy, dusty, or de-iced roads.

delivery vehicle.

commercial

−

Canadian Owners Follow the Maintenance Schedule for Severe Conditions. ＊

1 :

for

188

See dust and pollen filter on page replacement information under special driving conditions. Replace at 60,000 miles (96,000 km) or 3
years, then every 30,000 miles (48,000
km) or 2 years. Use normal schedule except in dusty condition. See information on maintenance and emission warranty on page

166

Maintenance 169

０３／０７／１５　１２：１８：３１　３１Ｓ９Ａ６２０　０１７５　

Maintenance Record

(forNormalandSevereSchedules)

You or the servicing dealer can record all completed maintenance here, whether you follow the schedule for normal conditions (page conditions (page

). Keep the receipts for all work done on your vehicle.

169

168

) or severe

5,000 mi 8,000 km

10,000 mi 16,000 km

15,000 mi 24,000 km

20,000 mi 32,000 km (or 1 year)

25,000 mi 40,000 km

30,000 mi 48,000 km

35,000 mi 56,000 km

40,000 mi 64,000 km (or 2 years)

Signature or dealer stamp mi/km

Date

mi/km

Date

mi/km

Date

mi/km

Date

mi/km

Date

mi/km

Date

mi/km

Date

mi/km

Date

170

Maintenance

45,000 mi 72,000 km

50,000 mi 80,000 km

55,000 mi 88,000 km

60,000 mi 96,000 km (or 3 years)

65,000 mi 104,000 km

70,000 mi 112,000 km

75,000 mi 120,000 km

80,000 mi 128,000 km (or 4 years)

Signature or dealer stamp mi/km

Date

mi/km

Date

mi/km

Date

mi/km

Date

mi/km

Date

mi/km

Date

mi/km

Date

mi/km

Date

０３／０７／１５　１２：１８：３８　３１Ｓ９Ａ６２０　０１７６　

Maintenance Record

(forNormalandSevereSchedules)

85,000 mi 136,000 km

90,000 mi 144,000 km

95,000 mi 152,000 km

100,000 mi 160,000 km (or 5 years)

105,000 mi 168,000 km

110,000 mi 176,000 km

115,000 mi 184,000 km

120,000 mi 192,000 km (or 6 years)

Signature or dealer stamp mi/km

Date

mi/km

Date

mi/km

Date

mi/km

Date

mi/km

Date

mi/km

Date

mi/km

Date

mi/km

Date

125,000 mi 200,000 km

130,000 mi 208,000 km

135,000 mi 216,000 km

140,000 mi 224,000 km (or 7 years)

145,000 mi 232,000 km

150,000 mi 240,000 km

155,000 mi 248,000 km

160,000 mi 256,000 km (or 8 years)

Signature or dealer stamp mi/km

Date

mi/km

Date

mi/km

Date

mi/km

Date

mi/km

Date

mi/km

Date

mi/km

Date

mi/km

Date

Maintenance 171

０３／０７／１５　１２：１８：４４　３１Ｓ９Ａ６２０　０１７７　

Fluid Locations

ENGINE OIL FILL CAP

ENGINE OIL DIPSTICK (Orange handle)

POWER STEERING FLUID (Red cap)

ENGINE COOLANT RESERVOIR

RADIATOR CAP

172

Maintenance

BRAKE FLUID (Gray cap)

WASHER FLUID (Blue cap)

CLUTCH FLUID (5-speed Manual Transmission only) (Gray cap)

AUTOMATIC TRANSMISSION FLUID DIPSTICK (Yellow loop)

０３／０７／１５　１２：１８：５５　３１Ｓ９Ａ６２０　０１７８　

Adding Engine Oil

ENGINE OIL FILL CAP

Recommended Engine Oil Oil is a major contributor to your engine’s performance and longevity. Always use a premium-grade 5W-20
detergent oil displaying the API Certification Seal. This seal indicates the oil is energy conserving, and that it meets the American Petroleum Institute’s latest requirements.

Unscrew and remove the engine oil fill cap on top of the valve cover. Pour in the oil slowly and carefully so you do not spill. Clean up any spills immediately. Spilled oil could damage components in the engine compartment. Install the engine oil fill cap and tighten it securely. Wait a few minutes and recheck the oil level. Do not fill above the upper mark; you could damage the engine.

API CERTIFICATION SEAL

Adding Engine Oil

Honda Motor Oil is the preferred 5W-20 lubricant for your vehicle. It is highly recommended that you use Honda Motor Oil in your vehicle for optimum engine protection. Make sure the API Certification Seal says ‘‘For Gasoline Engines’’.

The oil viscosity or weight is provided on the container’s label. 5W-20 oil is formulated for year- round protection of your Honda to improve cold weather starting and fuel economy.

Ambient Temperature

Maintenance

173

０３／０７／１５　１２：１９：０６　３１Ｓ９Ａ６２０　０１７９　

Adding Engine Oil, Changing the Oil and Filter

Synthetic Oil You may use a synthetic motor oil if it meets the same requirements given for a conventional motor oil: it displays the API Certification Seal and it is the proper weight. You must follow the oil and filter change intervals given on the maintenance schedule.

Engine Oil Additives Your Honda does not require any oil additives. Additives may adversely affect your engine’s or transmission’s performance and durability.

Changing the Oil and Filter Always change the oil and filter according to the recommendations in the maintenance schedule. The oil and filter collect contaminants that can damage your engine if they are not removed regularly.

Changing the oil and filter requires special tools and access from underneath the vehicle. The vehicle should be raised on a service station- type hydraulic lift for this service. Unless you have the knowledge and proper equipment, you should have this maintenance done by a skilled mechanic.

WASHER

OIL DRAIN BOLT

1.

2.

Run the engine until it reaches normal operating temperature, then shut it off.

Open the hood and remove the engine oil fill cap. Remove the oil drain bolt and washer from the bottom of the engine. Drain the oil into an appropriate container.

174

Maintenance

０３／０７／１５　１２：１９：１８　３１Ｓ９Ａ６２０　０１８０　

Changing the Oil and Filter

OIL FILTER

5.

Put a new washer on the drain bolt, then reinstall the drain bolt. Tighten it to: 33 lbf·ft (44 N·m , 4.5 kgf·m)

6.

Refill the engine with the recom- mended oil.

NOTICE: Improper disposal of engine oil can be harmf ul to the environment. If you change your own oil, please dispose of the used oil properly. Put it in a sealed container and take it to a recycling center. Do not discard it in a trash bin or dump it on the ground.

3.

Remove the oil filter and let the remaining oil drain. A special wrench (available from your Honda dealer) is required.

4.

Install a new oil filter according to the instructions that come with it.

Engine oil change capacity (including filter): 4.4 US qt (4.2 )

7.

8.

9.

Replace the engine oil fill cap. Start the engine. The oil pressure indicator light should go out within 5 seconds. If it does not, turn off the engine and check your work.

Let the engine run for several minutes, then check the drain bolt and oil filter for leaks.

Turn off the engine and let it sit for several minutes, then check the oil level on the dipstick. If necessary, add more oil.

Maintenance 175

０３／０７／１５　１２：１９：２７　３１Ｓ９Ａ６２０　０１８１　

Engine Coolant

Adding Engine Coolant

RESERVE TANK

If the coolant level in the reserve tank is at or below the MIN line, add coolant to bring it up to the MAX line. Inspect the cooling system for leaks.

176

Maintenance

If the reserve tank is completely empty, you should also check the coolant level in the radiator.

Removing the radiator cap while the engine is hot can cause the coolant to spray out, seriously scalding you.

Always let the engine and radiator cool down before removing the radiator cap.

Always use Honda All Season Antifreeze/Coolant Type 2. This coolant is pre-mixed with 50 percent antifreeze and 50 percent water. Never add straight antifreeze or plain water.

If Honda antifreeze/coolant is not available, you may use another major-brand non-silicate coolant as a temporary replacement. Make sure it is a high-quality coolant recommended for aluminum engines. Continued use of any non-Honda coolant can result in corrosion, causing the cooling system to malfunction or fail. Have the cooling system flushed and refilled with Honda antifreeze/coolant as soon as possible.

０３／０７／１５　１２：１９：３７　３１Ｓ９Ａ６２０　０１８２　

RADIATOR CAP

RESERVE TANK

1.

When the radiator and engine are cool, relieve any pressure in the cooling system by turning the radiator cap counterclockwise, without pressing down.

2.

Remove the radiator cap by pushing down and turning counterclockwise.

3.

The coolant level should be up to the base of the filler neck. Add coolant if it is low.

Pour the coolant slowly and carefully so you do not spill. Clean up any spill immediately; it could damage components in the engine compartment.

4.

Put the radiator cap back on and tighten it.

Engine Coolant

5.

Pour coolant into the reserve tank. Fill it to halfway between the MAX and MIN marks. Put the cap back on the reserve tank.

Do not add any rust inhibitors or other additives to your vehicle’s cooling system. They may not be compatible with the coolant or engine components.

Maintenance 177

０３／０７／１５　１２：１９：４４　３１Ｓ９Ａ６２０　０１８３　

NOTICE: Do not use engine antif reeze or a vinegar/water solution in the windshield washer reservoir. Antif reeze can damage your vehicle’s paint, while a vinegar/water solution can damage the windshield washer pump. Use only commercially-available windshield washer f luid.

Windshield Washers

Check the level in the windshield washer reservoir at least monthly during normal use.

The low washer CanadianModels: level indicator will light when the level is low (see page

59

).

Fill the reservoir with a good-quality windshield washer fluid. This increases the cleaning capability and prevents freezing in cold weather.

When you refill the reservoir, clean the edges of the windshield wiper blades with windshield washer fluid on a clean cloth. This will help to condition the blade edges.

178

Maintenance

０３／０７／１５　１２：１９：５７　３１Ｓ９Ａ６２０　０１８４　

Automatic Transmission

DIPSTICK

UPPER MARK LOWER MARK

Check the fluid level with the engine at normal operating temperature.

3.

Insert the dipstick all the way into the transmission.

1.

Park the vehicle on level ground. Shut off the engine.

2.

Remove the dipstick (yellow loop) from the transmission, and wipe it with a clean cloth.

4.

Remove the dipstick and check the fluid level. It should be between the upper and lower marks.

Transmission Fluid

5.

If the level is below the lower mark, add fluid into the filler hole to bring it to the upper mark.

Always use Honda ATF-Z1
(Automatic Transmission Fluid). If it’s not available, you may use a DEXRON III automatic transmission fluid as a temporary replacement. However, continued use can affect the shift quality. Have the transmission flushed and refilled with Honda ATF-Z1 as soon as it is convenient.

To thoroughly flush the transmission, the technician should drain and refill it with Honda ATF-Z1, then drive the vehicle for a short distance. Do this three times. Then drain and refill the transmission a final time.

CONTINUED

Maintenance 179

０３／０７／１５　１２：２０：０８　３１Ｓ９Ａ６２０　０１８５　

Transmission Fluid

6.

Insert the dipstick all the way back into the transmission.

The transmission should be drained and refilled with new fluid according to the time and distance recommen- dations in the maintenance schedule.

If you are not sure how to add fluid, contact your Honda dealer.

180

Maintenance

5-speed Manual Transmission

WASHER

FILLER BOLT

Put a new washer on the filler bolt, then reinstall the filler bolt and tighten it securely.

If Honda MTF is not available, you may use an SAE 10W-30 or 10W-40
viscosity motor oil with the API Certification seal that says ‘‘FOR GASOLINE ENGINES’’ as a temporary replacement. However, motor oil does not contain the proper additives, and continued use can cause stiffer shifting. Replace as soon as it is convenient.

The transmission should be drained and refilled with new fluid according to the time and distance recommendations in the maintenance schedule.

If you are not sure how to add fluid, contact your Honda dealer.

Correct level

Check the fluid level with the transmission at normal operating temperature and the vehicle sitting on level ground. Remove the transmission filler bolt and carefully feel inside the bolt hole with your finger. The fluid level should be up to the edge of the bolt hole. If it is not, add Honda Manual Transmission Fluid (MTF) until it starts to run out of the hole.

０３／０７／１５　１２：２０：１９　３１Ｓ９Ａ６２０　０１８６　

Brake Fluid Check the brake fluid level in the reservoirs monthly. Replace brake fluid according to the time recommendation in the maintenance schedule.

Always use Honda Heavy Duty Brake Fluid DOT 3. If it is not available, you should use only DOT 3
or DOT 4 fluid, from a sealed container, as a temporary replacement.

Using any non-Honda brake fluid can cause corrosion and decrease the life of the system. Have the brake system flushed and refilled with Honda Heavy Duty Brake Fluid DOT 3 as soon as possible.

Brake fluid marked DOT 5 is not compatible with your vehicle’s braking system and can cause extensive damage.

Brake and Clutch Fluid

MAX

Clutch Fluid ManualTransmissiononly

MAX

MIN

The fluid level should be between the MIN and MAX marks on the side of the reservoir. If the level is at or below the MIN mark, your brake system needs attention. Have the brake system inspected for leaks or worn brake pads.

MIN

The fluid level should be between the MIN and MAX marks on the side of the reservoir. If it is not, add brake fluid to bring it up to that level. Use the same fluid specified for the brake system.

Low fluid level can indicate a leak in the clutch system. Have this system inspected as soon as possible.

Maintenance 181

０３／０７／１５　１２：２０：２９　３１Ｓ９Ａ６２０　０１８７　

Power Steering Fluid, Hood Latch

Always use Honda Power Steering Fluid. You may use another power steering fluid as an emergency replacement, but have the power steering system flushed and refilled with Honda PSF as soon as possible.

A low power steering fluid level can indicate a leak in the system. Check the fluid level frequently, and have the system inspected as soon as possible.

Turning the steering wheel to

NOTICE: f ull lef t or right lock and holding it there can damage the power steering pump.

Hood Latch

LATCH ASSEMBLY

Clean the hood latch assembly with a mild cleaner, then lubricate it with a multipurpose grease. Lubricate all the moving parts (as shown), including the pivot. Follow the time and distance recommendations in the Maintenance Schedule. If you are not sure how to clean and grease the latch, contact your Honda dealer.

Power Steering Fluid

UPPER LEVEL

LOWER LEVEL

Check the level on the side of the reservoir when the engine is cold. The fluid should be between the UPPER LEVEL and LOWER LEVEL. If not, add power steering fluid to the UPPER LEVEL.

182

Maintenance

０３／０７／１５　１２：２０：４０　３１Ｓ９Ａ６２０　０１８８　

Headlight Aiming The headlights were properly aimed when your vehicle was new. If you regularly carry heavy items in the cargo area or pull a trailer, a readjustment may be required. Adjustments should be performed by a Honda dealer or other qualified mechanic.

Replacing a Headlight Bulb Your vehicle has halogen headlight bulb. Handle it by its steel base and protect the glass from contact with your skin or hard objects. If you touch the glass, clean it with denatured alcohol and a clean cloth.

NOTICE: Halogen headlight bulbs get very hot when lit. Oil, perspiration, or a scratch on the glass can cause the bulb to overheat and shatter.

Lights

WEATHER SEAL

BULB

1.

HOLD-DOWN WIRE

CONNECTOR Remove the electrical connector from the bulb by pulling the connector straight back.

2.

Remove the rubber weather seal by pulling on the tab.

CONTINUED

Maintenance 183

０３／０７／１５　１２：２０：５１　３１Ｓ９Ａ６２０　０１８９　

Lights

3.

4.

Unclip the end of the hold-down wire from its slot. Pivot it out of the way and remove the bulb.

Insert the new bulb into the hole, making sure the tabs are in their slots. Pivot the hold-down wire back in place, and clip the end into the slot.

5.

Reinstall the rubber seal. Make sure it is right side up; it is marked ‘‘TOP.’’

6.

Push the electrical connector onto the new bulb.

184

Maintenance

Replacing the Front Side Marker/ Turn Signal Light Bulb

BULB

3.

Pull the bulb straight out of its socket. Push the new bulb straight into the socket until it bottoms.

4.

Insert the socket back into the headlight assembly. Turn it clockwise to lock it in place.

5.

Test the lights to make sure the new bulb is working.

1.

The front side marker/turn signal light is next to the headlight bulb.

2.

Remove the socket from the headlight assembly by turning it one-quarter turn counterclockwise.

０３／０７／１５　１２：２１：０２　３１Ｓ９Ａ６２０　０１９０　

Replacing a Front Parking Light Bulb

BOLT

COVER

HOLDING CLIP

1.

The front parking light is next to the headlight bulb.

2.

Use a wrench to loosen the bolt on the battery hold-down. Remove the seven holding clips from the cover by using a flat-tipped screwdriver. Then pull the radiator support cover away.

BULB Remove the socket from the 3. headlight assembly by turning it one-quarter turn counterclockwise.

4.

Pull the bulb straight out of its socket. Push the new bulb straight into the socket until it bottoms.

Lights

5.

6.

7.

Insert the socket back into the headlight assembly. Turn it clockwise to lock it in place.

Turn on the parking lights and check that the new bulb is working.

Reinstall the radiator support cover. Lock the holding clips by pushing on the center of each clip. Tighten the bolt on the battery hold-down.

Maintenance 185

０３／０７／１５　１２：２１：１４　３１Ｓ９Ａ６２０　０１９１　

Lights

Replacing Rear Bulbs

COVER

SCREW

BULBS

1.

Open the tailgate. Place a cloth on the edge of the cover. Remove the covers by carefully prying on the edge with a small flat-tipped screwdriver.

2.

Use a Phillips-head screwdriver to remove the taillight assembly mounting screw under each cover.

3.

Pull the taillight assembly out of the rear pillar.

4.

Determine which of the four bulbs is burned out: stop/taillight, back- up light, turn signal, or side marker.

5.

Remove the socket by turning it one-quarter turn counterclockwise.

186

Maintenance

０３／０７／１５　１２：２１：２３　３１Ｓ９Ａ６２０　０１９２　

6.

Pull the bulb straight out of its socket. Push the new bulb straight into the socket until it bottoms.

7.

Reinstall the socket into the light assembly by turning it clockwise until it locks.

8.

Test the lights to make sure the new bulb is working.

9.

Align the clips on the taillight assembly with the holes in the body, then push the taillight assembly into place. Tighten the two mounting screws securely and reinstall the covers.

Seat Belts

LOOP

Lights, Seat Belts

Dirt build-up in the loops of the seat belt anchors can cause the belts to retract slowly. Wipe the insides of the loops with a clean cloth dampened in mild soap and warm water or isopropyl alcohol.

If your seat belts get dirty, use a soft brush with a mixture of mild soap and warm water to clean them. Do not use bleach, dye, or cleaning solvents. Let the belts air dry before you use the vehicle.

Maintenance

187

０３／０７／１５　１２：２１：３２　３１Ｓ９Ａ６２０　０１９３　

Floor Mats, Dust and Pollen Filter

Floor Mats

If you use a non-Honda floor mat, make sure it fits properly and that it can be used with the floor mat anchors. Do not put additional floor mats on top of the anchored mats.

The driver’s floor mat that came with your vehicle hooks over the floor mat anchor. This keeps the floor mat from sliding forward and possibly interfering with the pedals.

If you remove the driver’s floor mat, make sure to re-anchor it when you put it back in your vehicle.

188

Maintenance

Dust and Pollen Filter This filter removes the dust and pollen that is brought in from the outside through the heating and cooling system/climate control system.

Have your Honda dealer replace this filter every 30,000 miles (48,000 km) under normal conditions. It should be replaced every 15,000 miles (24,000 km) if you drive primarily in urban areas that have high concentrations of soot in the air, or if the flow from the climate control system becomes less than usual.

０３／０７／１５　１２：２１：４４　３１Ｓ９Ａ６２０　０１９４　

Wiper Blades

Check the condition of the wiper blades at least every six months. Replace them if you find signs of cracking in the rubber, areas that are getting hard, or if they leave streaks and unwiped areas when used.

1.

Front: Raise the wiper arm off the windshield.

Rear: Raise the wiper arm off the hatch glass and hold it.

LOCK TAB

BLADE

2.

Disconnect the blade assembly from the wiper arm by pushing in the lock tab. Hold the lock tab in while you push the blade assembly toward the base of the arm.

If you are changing the rear wiper blade, go to step 6.

3.

4.

Remove the blade from its holder by grasping the tabbed end of the blade. Pull firmly until the tabs come out of the holder.

Examine the new wiper blades. If they have no plastic or metal rein- forcement along the back edge, remove the metal reinforcement strips from the old wiper blade and install them in the slots along the edge of the new blade.

Maintenance

189

０３／０７／１５　１２：２１：５７　３１Ｓ９Ａ６２０　０１９５　

Wiper Blades, Tires

BLADE

REINFORCEMENT

5.

Slide the new wiper blade into the holder until the tabs lock.

6.

Slide the wiper blade assembly onto the wiper arm. Make sure it locks in place.

7.

Lower the wiper arm down against the windshield or the hatch glass.

190

Maintenance

Tires To safely operate your vehicle, your tires must be the proper type and size, in good condition with adequate tread, and correctly inflated.

Inflation Keeping the tires properly inflated provides the best combination of handling, tread life, and riding comfort.

The following pages give more detailed information on how to take care of your tires and what to do when they need to be replaced.

Underinflated tires wear unevenly, adversely affect handling and fuel economy, and are more likely to fail from being overheated.

Using tires that are excessively worn or improperly inflated can cause a crash in which you can be seriously hurt or killed.

Follow all instructions in this owner’s manual regarding tire inflation and maintenance.

Overinflated tires can make your vehicle ride more harshly, are more prone to damage from road hazards, and wear unevenly.

We recommend that you visually check your tires every day. If you think a tire might be low, check it immediately with a tire gauge.

０３／０７／１５　１２：２２：１０　３１Ｓ９Ａ６２０　０１９６　

Use a gauge to measure the air pressure at least once a month. Even tires that are in good condition may lose one to two psi (10 to 20 kPa, 0.1
to 0.2 kgf/cm ) per month. Remember to check the spare tire at the same time.

Check the pressure in the tires when they are cold. This means the vehicle has been parked for at least three hours, or driven less than 1 mile (1.6
km).

Add or release air, if needed, to match the recommended cold tire pressures on the third column.

If you check the pressure when the tires are hot [the vehicle has been driven several miles (kilometers)], you will see readings 4 to 6 psi (30 to 40 kPa, 0.3 to 0.4 kgf/cm ) higher than the cold reading. This is normal; do not release air to match the cold pressure.

You should get your own tire pressure gauge and use it whenever you check your tire pressures. This will make it easier for you to tell if a pressure loss is due to a tire problem and not due to a variation between gauges.

Tires

RecommendedTirePressuresfor NormalDriving

Tire Size

P205/70R15 95S

Cold Tire Pressure for Normal Driving Front/Rear: 26 psi (180 kPa , 1.8 kgf/cm )

For convenience, the recommended tire sizes and cold air pressures are on a label on the driver’s doorjamb.

For additional technical information about your tires, see page

230

Tubeless tires have some ability to self-seal if they are punctured. You should look closely for punctures if a tire starts losing pressure.

CONTINUED

Maintenance

191

０３／０７／１５　１２：２２：２３　３１Ｓ９Ａ６２０　０１９７　

Tires

TirePressureAdjustmentforHigh SpeedDriving Honda strongly recommends that you not drive faster than posted speed limits and conditions allow. If you decide it is safe to drive at high speeds, be sure to adjust the cold tire pressures as shown below. If you do not adjust the tire pressure, exces- sive heat can build up and cause sudden tire failure.

Tire Size

P205/70R15 95S

Cold Tire Pressure for Speed over 100
mph (160 km/h) 35 psi (240 kPa , 2.4 kgf/cm )

When you return to normal speed driving, be sure to readjust the tire pressure for normal driving. You should wait until the tires are cold before adjusting the tire pressure.

Tire Inspection Every time you check inflation, you should also examine the tires for damage, foreign objects, and wear. You should look for:

Bumps or bulges in the tread or side of the tire. Replace the tire if you find either or these conditions.

Cuts, splits, or cracks in the side of the tire. Replace the tire if you can see fabric or cord.

Excessive tread wear. When you see a 1/2 inch (12.7 mm) wide band running across the tread, there is less than 1/16 inch (1.6
mm) of tread left on the tire. Replace the tire if you can see three or more tread wear indicators around it.

192

Maintenance

INDICATOR LOCATION MARKS

TREAD WEAR INDICATORS

０３／０７／１５　１２：２２：３５　３１Ｓ９Ａ６２０　０１９８　

Tire Maintenance In addition to proper inflation, correct wheel alignment helps to decrease tire wear. If you find a tire is worn unevenly, have your dealer check the wheel alignment.

Have your dealer check the tires if you feel a consistent vibration while driving. A tire should always be rebalanced if it is removed from the wheel. When you have new tires installed, make sure they are balanced. This increases riding comfort and tire life. For best results, have the installer perform a dynamic balance.

(Onlyonvehiclesequippedwith aluminumwheels) NOTICE: damage your vehicle’s aluminum wheels. Use only genuine Honda wheels weights f or balancing.

Improper wheel weights can

Tire Rotation

Front

Front

(For Directional Tires and Wheels)

(For Non-directional Tires and Wheels) To help increase tire life and distribute wear more evenly, rotate the tires every 10,000 miles (16,000
km). Move the tires to the positions shown in the chart each time they are rotated. If you purchase directional tires, rotate only front-to- back.

Tires

Replacing Tires Replace your tires with radial tires of the same size, load range, speed rating, and maximum cold tire pressure rating (as shown on the tire’s sidewall). Mixing radial and bias-ply tires on your vehicle can reduce braking ability, traction, and steering accuracy. Using tires of a different size or construction can cause the ABS to work inconsistently.

It is best to replace all four tires at the same time. If that is not possible or necessary, then replace the two front tires or the rear tires as a pair. Replacing just one tire can seriously affect your vehicle’s handling.

Maintenance

193

０３／０７／１５　１２：２２：４９　３１Ｓ９Ａ６２０　０１９９　

Tires

Installing improper tires on your vehicle can affect handling and stability. This can cause a crash in which you can be seriously hurt or killed.

Always use the size and type of tires recommended in this owner’s manual.

Wheels and Tires

Wheels:

15 x 6JJ

Tires:

P205/70R15 95S

228

for information about

See page DOT Tire Quality Grading. Replacement wheels are available at your Honda dealer.

194

Maintenance

Tire Chains Because your Honda has limited tire clearance, mount only SAE Class ‘‘S’’ cable-type traction devices on the front tires. Use traction devices only when required by driving conditions or local laws. Make sure they are the correct size for your tires. Metal link- type ‘‘chains’’ should not be used.

Winter Driving Tires marked ‘‘M S’’ or ‘‘All Season’’ on the sidewall have an all- weather tread design suitable for most winter driving conditions.

＋

For the best performance in snowy or icy conditions, you should install snow tires or tire chains. They may be required by local laws under certain conditions.

Snow Tires If you mount snow tires on your Honda, make sure they are radial tires of the same size and load range as original tires. Mount snow tires on all four wheels. The traction provided by snow tires on dry roads may be lower than your original tires. Check with the tire dealer for maximum speed recommendations.

０３／０７／１５　１２：２２：５４　３１Ｓ９Ａ６２０　０２００　

When installing cables, follow the manufacturer’s instructions, and mount them as tight as you can. Make sure they are not contacting the brake lines or suspension. Drive slowly with them installed. If you hear them coming into contact with the body or chassis, stop and investigate. Remove them as soon as you begin driving on cleared roads.

NOTICE: Traction devices that are the wrong size or improperly installed can damage your vehicle’s brake lines, suspension, body, and wheels. Stop driving if they are hitting any part of the vehicle.

Tires

Maintenance 195

０３／０７／１５　１２：２３：０１　３１Ｓ９Ａ６２０　０２０１　

Checking the Battery

TEST INDICATOR WINDOW

Check the condition of the battery monthly by looking at the test indicator window. The label on the battery explains the test indicator’s colors.

196

Maintenance

Check the terminals for corrosion (a white or yellowish powder). To remove it, cover the terminals with a solution of baking soda and water. It will bubble up and turn brown. When this stops, wash it off with plain water. Dry off the battery with a cloth or paper towel. Coat the terminals with grease to help prevent future corrosion.

If additional battery maintenance is needed, see your Honda dealer or a qualified technician.

Battery posts,

WARNING: terminals, and related accessories contain lead and lead compounds. Wash your hands after handling.

The battery gives off explosive hydrogen gas during normal operation.

A spark or flame can cause the battery to explode with enough force to kill or seriously hurt you.

Wear protective clothing and a face shield, or have a skilled mechanic do the battery maintenance.

０３／０７／１５　１２：２３：１５　３１Ｓ９Ａ６２０　０２０２　

If you need to park your vehicle for an extended period (more than one month), there are several things you should do to prepare it for storage. Proper preparation helps prevent deterioration and makes it easier to get your vehicle back on the road. If possible, store your vehicle indoors.

Fill the fuel tank.

Block the rear wheels.

If the vehicle is to be stored for a longer period, it should be supported on jackstands so the tires are off the ground.

Leave one window open slightly (if the vehicle is being stored indoors).

Change the engine oil and filter.

Disconnect the battery.

Wash and dry the exterior completely.

Clean the interior. Make sure the carpeting, floor mats, etc. are completely dry.

Leave the parking brake off. Put the transmission in Reverse (5-speed manual) or Park (automatic).

Support the front and rear wiper blade arms with a folded towel or rag so they do not touch the windshield.

To minimize sticking, apply a silicone spray lubricant to all door and tailgate seals. Also, apply a vehicle body wax to the painted surfaces that mate with the door and tailgate seals.

Vehicle Storage

Cover the vehicle with a ‘‘breathable’’ cover, one made from a porous material such as cotton. Non-porous materials, such as plastic sheeting, trap moisture, which can damage the paint.

If possible, run the engine periodically until it reaches full operating temperature (the cooling fan cycles on and off twice). Preferably do this once a month.

If you store your vehicle for 12
months or longer, have your Honda dealer perform the inspections called for in the 24 months maintenance schedule (Normal Conditions) as soon as you take it out of storage (see page called for in the maintenance schedule are not needed unless the vehicle has actually reached that time or mileage.

). The replacements

168

Maintenance 197

０３／０７／１５　１２：２３：１７　３１Ｓ９Ａ６２０　０２０３　

198

０３／０７／１５　１２：２３：２２　３１Ｓ９Ａ６２０　０２０４　

Taking Care of the Unexpected

This section covers the more common problems that motorists experience with their vehicles. It gives you information about how to safely evaluate the problem and what to do to correct it. If the problem has stranded you on the side of the road, you may be able to get going again. If not, you will also find instructions on getting your vehicle towed.

Changing a Flat Tire If the Engine Won’t Start Jump Starting If the Engine Overheats Low Oil Pressure Indicator Charging System Indicator Malfunction Indicator Lamp Brake System Indicator Emergency Towing Closing the Moonroof Fuses Fuse Locations

.................... ............. ................................ .............. ......... .......... ....... ............... ...................... .................. .............................................. ..............................

. 200
. 207
. 209
. 211
. 213
. 213
. 214
. 215
. 216
. 217
. 218
. 221

Taking Care of the Unexpected 199

０３／０７／１５　１２：２３：３１　３１Ｓ９Ａ６２０　０２０５　

Changing a Flat Tire

If you have a flat tire while driving, stop in a safe place to change it. Drive slowly along the shoulder until you get to an exit or an area to stop that is far away from the traffic lanes.

The vehicle can easily roll off the jack, seriously injuring anyone underneath.

Follow the directions for changing a tire exactly, and never get under the vehicle when it is supported only by the jack.

1.

Park the vehicle on firm, level and non-slippery ground. Put the transmission in Park (automatic) or Reverse (manual). Apply the parking brake. If you are towing a trailer, unhitch the trailer.

2.