Login- Download PDF Manual
-
０４／０７／１６ １３：１４：１０ ３１Ｓ５Ｔ６３０ ０１１４
Fueling
Pull
Service Station Procedures
ATTACHMENT
Gasoline is highly flammable and explosive. You can be burned or seriously injured when handling fuel.
Stop the engine, and keep heat, sparks, and flames away. Handle fuel only outdoors. Wipe up spills immediately.
SLIT
1.
Park with the driver’s side closest to the gas pump.
2.
Open the fuel fill door by pulling on the handle to the left of the driver’s seat.
3.
4.
Remove the fuel fill cap slowly. You may hear a hissing sound as pressure inside the tank escapes. Put the attachment on the fuel fill cap into the slit on the fuel fill door.
Stop filling the tank after the fuel nozzle automatically clicks off. Do not try to ‘‘top off’’ the tank. Leave some room for the fuel to expand with temperature changes.
FUEL FILL CAP
Ifthefuelnozzlekeepsclickingoff even though the tank is not full, there may be a problem with your vehicle’s fuel vapor recovery system. The system helps keep fuel vapors from going into the atmosphere. Consult your dealer.
CONTINUED
111
０４／０７／１６ １３：１４：１９ ３１Ｓ５Ｔ６３０ ０１１５
Service Station Procedures
5.
Screw the fuel fill cap back on until it clicks at least three times. If you do not properly tighten the cap, the Malfunction Indicator Lamp may come on (see page 178
).
6.
Push the fuel fill door closed until it latches.
112
Opening and Closing the Hood
HOOD RELEASE HANDLE
LATCH
1.
2.
Park the vehicle, and set the parking brake. Pull the hood release handle located under the lower left corner of the dashboard. The hood will pop up slightly.
Put your fingers between the front edge of the hood near the center. The hood latch handle is above the ‘‘H’’ logo. Push this handle up until it releases the hood. Lift the hood.
If the hood latch handle moves stiffly, or if you can open the hood without lifting the handle, the mechanism should be cleaned and lubricated.
3.
Pull the support rod out of its clip and insert the end into the designated hole(s) in the hood.
０４／０７／１６ １３：１４：３１ ３１Ｓ５Ｔ６３０ ０１１６
GRIP
Oil Check
DIPSTICK
Service Station Procedures
CLIP
SUPPORT ROD
To close the hood, lift it up slightly to remove the support rod from the hole. Put the support rod back into its holding clip. Lower the hood to about a foot (30 cm) above the fender, then let it drop. Make sure it is securely latched.
UPPER MARK LOWER MARK
Wait a few minutes after turning the engine off before you check the oil.
1.
Remove the dipstick (orange loop).
4.
Remove the dipstick again and check the level. It should be between the upper and lower marks.
2.
Wipe the dipstick with a clean cloth or paper towel.
3.
Insert it all the way back in its tube.
If it is near or below the lower mark, see
Adding Oil
on page
138
113
０４／０７／１６ １３：１４：４５ ３１Ｓ５Ｔ６３０ ０１１７
Service Station Procedures, Fuel Economy
Engine Coolant Check
MAX
RESERVE TANK
MIN
Look at the coolant level in the radiator reserve tank. Make sure it is between the MAX and MIN lines. If Adding it is below the MIN line, see Engine Coolant for 141
information on adding the proper coolant.on page
Owner’s Maintenance on page
Refer to Checks for information about checking other items on your vehicle.
132
114
Improving Fuel Economy
Always maintain your vehicle according to the maintenance Owner’s schedule. See Maintenance Checks 132
).
(see page
an underinflated tire Forexample, causes more ‘‘rolling resistance,’’ which uses more fuel.
The build-up of snow or mud on your vehicle’s underside adds weight and rolling resistance. Frequent cleaning helps your fuel mileage and reduces the chance of corrosion.
Drive moderately. Rapid acceleration, abrupt cornering, and hard braking use more fuel.
Always drive in the highest gear possible.
Try to maintain a constant speed. Every time you slow down and speed up, your vehicle uses extra fuel. Use the cruise control when appropriate.
Combine several short trips into one.
The air conditioning puts an extra load on the engine which makes it use more fuel. Use the fresh-air ventilation when possible.
０４／０７／１６ １３：１４：５５ ３１Ｓ５Ｔ６３０ ０１１８
Modifying your vehicle, or installing some non-Honda accessories, can make it unsafe. Before you make any modifications or add any accessories, be sure to read the following information.
Accessories Your dealer has Honda accessories that allow you to personalize your vehicle. These accessories have been designed and approved for your vehicle, and are covered by warranty.
Although non-Honda accessories may fit on your vehicle, they may not meet factory specifications, and could adversely affect your vehicle’s handling and stability (see page 116
).
Improper accessories or modifications can affect your vehicle’s handling, stability, and performance, and cause a crash in which you can be hurt or killed.
Follow all instructions in this owner’s manual regarding accessories and modifications.
When properly installed, cellular phones, alarms, two-way radios, and low-powered audio systems should not interfere with your vehicle’s computer controlled systems, such as your airbags and anti-lock brakes.
Accessories and Modifications
Before installing any accessory:
Make sure the accessory does not obscure any lights, or interfere with proper vehicle operation or performance.
Be sure electronic accessories do not overload electrical circuits (see page proper operation.
) or interfere with
181
Before installing any electronic accessory, have the installer contact your dealer for assistance. If possible, have your dealer inspect the final installation.
115
０４／０７／１６ １３：１５：０３ ３１Ｓ５Ｔ６３０ ０１１９
Accessories and Modifications
Larger or smaller wheels and tires can interfere with the operation of your vehicle’s anti-lock brakes and other systems.
Modifying your steering wheel or any other part of your vehicle’s safety systems could make the systems ineffective.
If you plan to modify your vehicle, consult your dealer.
Modifying Your Vehicle Removing parts from your vehicle, or replacing components with non-Honda components could seriously affect your vehicle’s handling, stability, and reliability.
Some examples are:
Lowering your vehicle with a non-Honda suspension kit that significantly reduces ground clearance can allow the undercarriage to hit speed bumps or other raised objects, which could cause the airbags to deploy.
Raising your vehicle with a non-Honda suspension kit can affect the handling and stability.
Non-Honda wheels, because they are a universal design, can cause excessive stress on suspension components.
116
０４／０７／１６ １３：１５：１２ ３１Ｓ５Ｔ６３０ ０１２０
Carrying Cargo
DOOR POCKET
DRIVER’S POCKET
Your vehicle has several convenient storage areas:
Glove box Front door pocket Console compartment Cargo area
However, carrying too much cargo, or improperly storing it, can affect your vehicle’s handling, stability, stopping distance, and tires, and make it unsafe. Before carrying any type of cargo, be sure to read the following pages.
117
CARGO AREA
CONSOLE COMPARTMENT
GLOVE BOX
(850
−
750 (5
×
150) = 100 lbs.)
5.
Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity in Step 4.
０４／０７／１６ １３：１５：２２ ３１Ｓ５Ｔ６３０ ０１２１
Carrying Cargo
Load Limits The maximum load for your vehicle is 850 lbs (395 kg). This figure includes total weight of all occupants, cargo, and accessories.
Overloading or improper loading can affect handling and stability and cause a crash in which you can be hurt or killed.
Follow all load limits and other loading guidelines in this manual.
118
Steps for Determining Correct Load Limit:
1.
2.
3.
4.
Locate the statement, ‘‘the combined weight of occupants and cargo should never exceed 850
lbs’’ on your vehicle’s placard. [The placard is on the driver’s doorjamb.]Determine the combined weight of the driver and passengers that will be riding in your vehicle.
Subtract the combined weight of the driver and passengers from 850 pounds or 395 kilograms.
The resulting figure equals the available amount of cargo and luggage load capacity. For example, if the maximum load is 850 lbs and there will be five 150
lb. passengers in your vehicle, the amount of available cargo and luggage load capacity is 100 lbs.０４／０７／１６ １３：１５：３１ ３１Ｓ５Ｔ６３０ ０１２２
Carrying Cargo
Carrying Items in the Passenger Compartment
Store or secure all items that could be thrown around and hurt someone during a crash.
Be sure items placed on the floor behind the front seats cannot roll under the seats and interfere with the driver’s ability to operate the pedals or the seat.
Keep the glove box closed while driving. If it is open, a passenger could injure their knees during a crash or sudden stop.
Carrying Cargo in the Cargo Area
Distribute cargo evenly on the floor of the cargo area, placing the heaviest items on the bottom and as far forward as possible. Tie down items that could be thrown about the vehicle during a crash or sudden stop.
Do not place items on the cargo area cover, or stack objects higher than the top of the back seat. They could block your view and be thrown about the vehicle during a crash or sudden stop.
If you carry large items that prevent you from closing the hatch, exhaust gas can enter the passenger area. To avoid the possibility of poisoning on page 47
, follow the instructions
carbon monoxide
119
０４／０７／１６ １３：１５：３８ ３１Ｓ５Ｔ６３０ ０１２４
Driving
This section gives you tips on starting the engine under various conditions, and how to operate the manual transmission. It also includes important information on parking your vehicle, and the braking system.
Preparing to Drive Starting the Engine Manual Transmission Parking Towing a Trailer Braking System Anti-lock Brakes (ABS)
........................ ....................... ................... ........................................... ........................... ............................. ...............
. 122
. 123
. 124
. 126
. 126
. 127
. 128121
０４／０７／１６ １３：１５：５０ ３１Ｓ５Ｔ６３０ ０１２５
When you start the engine, check the gauges and indicator lights in the instrument panel (see page
51
).
6.
7.
Check the seat adjustment (see page
71
).
Check the adjustment of the inside and outside mirrors (see page
79
).
8.
Check the steering wheel adjustment (see page 63
).
9.
Make sure the doors and the hatch are securely closed and locked.
10.
Fasten your seat belt. Check that your passengers have fastened their seat belts (see page ).
16
Preparing to Drive
You should do the following checks and adjustments before you drive your vehicle.
1.
Make sure all windows, mirrors, and outside lights are clean and unobstructed. Remove frost, snow, or ice.
2.
Check that the hood is fully closed.
3.
Check that the hatch is fully closed.
4.
5.
Visually check the tires. If a tire looks low, use a gauge to check its pressure.
Check that any items you may be carrying are stored properly or fastened down securely.
122
０４／０７／１６ １３：１６：００ ３１Ｓ５Ｔ６３０ ０１２６
Starting the Engine
6.
If the engine fails to start, press the accelerator pedal all the way down and hold it there while starting to clear flooding. If the engine still does not start, return to step 5.
The engine is harder to start in cold weather. Also, the thinner air f ound at altitudes above 8,000 f eet (2,400
meters) adds to this problem.The immobilizer system protects your vehicle f rom thef t. If an improperly- coded key (or other device) is used, the engine’s f uel system is disabled. See Immobilizer System
on page
65
1.
Apply the parking brake.
2.
In cold weather, turn off all electrical accessories to reduce the drain on the battery.
3.
Push the clutch pedal down all the way.
4.
5.
Without touching the accelerator pedal, turn the ignition key to the START (III) position. Do not hold the key in START for more than 15 seconds at a time. If the engine does not start right away, pause for at least 10 seconds before trying again.
If the engine does not start within 15 seconds, or starts but stalls right away, repeat step 4 with the accelerator pedal pressed halfway down. If the engine starts, release pressure on the accelerator pedal so the engine does not race.
123
０４／０７／１６ １３：１６：０６ ３１Ｓ５Ｔ６３０ ０１２７
Manual Transmission
Rapid slowing or speeding-up can cause loss of control on slippery surfaces. If you crash, you can be injured.
Use extra care when driving on slippery surfaces.
Come to a full stop before you shift into Reverse. You can damage the transmission by trying to shift into Reverse with the vehicle moving. Push down the clutch pedal, and pause for a few seconds before shifting into Reverse, or shift into one of the forward gears for a moment. This stops the gears so they won’t ‘‘grind.’’
When slowing down, you can get extra braking from the engine by shifting to a lower gear. This extra braking can help you maintain a safe speed and prevent your brakes from overheating while going down a steep hill. Before downshifting, make sure the engine speed will not go into the tachometer’s red zone in the lower gear.
The manual transmission is syn- chronized in all forward gears for smooth operation. It has a lockout so you cannot shift directly from Fifth to Reverse. When shifting up or down, make sure you push the clutch pedal down all the way, shift to the next gear, and let the pedal up gradually. When you are not shifting, do not rest your foot on the clutch pedal. This can cause your clutch to wear out faster.
124
０４／０７／１６ １３：１６：１３ ３１Ｓ５Ｔ６３０ ０１２８
Manual Transmission
Recommended Shift Points Drive in the highest gear that lets the engine run and accelerate smoothly. This will give you good fuel economy and effective emissions control. The following shift points are recommended:
Shift up
Normal acceleration
1st to 2nd 2nd to 3rd 3rd to 4th 4th to 5th
17 mph (27 km/h) 28 mph (45 km/h) 45 mph (72 km/h) 56 mph (90 km/h)
Engine Speed Limiter If you exceed the maximum speed for the gear you are in, the engine speed will enter into the tachometer’s red zone. If this occurs, you may feel the engine cut in and out. This is caused by a limiter in the engine’s computer controls. The engine will run normally when you reduce the RPM below the red zone.
Before downshifting, make sure the engine will not go into the tachometer’s red zone.
125
０４／０７／１６ １３：１６：２６ ３１Ｓ５Ｔ６３０ ０１２９
If the vehicle is facing uphill, turn the front wheels away from the curb, and put the transmission in first gear.
Towing a Trailer Your vehicle is not designed to tow a trailer, attempting to do so can void your warranties.
If the vehicle is facing downhill, turn the front wheels toward the curb, and put the transmission in reverse gear.
Make sure the parking brake is fully released before driving away. Driving with the parking brake partially set can overheat or damage the rear brakes.
Parking, Towing a Trailer
Parking Always use the parking brake when you park your vehicle. Make sure the parking brake is set firmly or your vehicle may roll if it is parked on an incline.
Parking Tips
Make sure the moonroof and the windows are closed.
Turn off the lights.
Place any packages, valuables, etc. in the cargo area, or take them with you.
Lock the doors.
Never park over dry leaves, tall grass, or other flammable materials. The hot three way catalytic converter could cause these materials to catch on fire.
126
０４／０７／１６ １３：１６：３５ ３１Ｓ５Ｔ６３０ ０１３０
Your vehicle is equipped with disc brakes at all four wheels. A power assist helps reduce the effort needed on the brake pedal. The ABS helps you retain steering control when braking very hard.
Check the brakes after driving through deep water. Apply the brakes moderately to see if they feel normal. If not, apply them gently and frequently until they do. Be extra cautious in your driving.
Resting your foot on the pedal keeps the brakes applied lightly, builds up heat, and reduces their effectiveness. It also keeps your brake lights on all the time, confusing drivers behind you.
Constant application of the brakes when going down a long hill builds up heat and reduces their effective- ness. Use the engine to assist the brakes by taking your foot off the accelerator and downshifting to a lower gear.
Braking System Design The hydraulic system that operates the brakes has two separate circuits. Each circuit works diagonally across the vehicle (the left-front brake is connected with the right-rear brake, etc.). If one circuit should develop a problem, you will still have braking at two wheels.
Braking System
Brake Wear Indicators If the brake pads need replacing, you will hear a distinctive, metallic screeching sound when you apply the brake pedal. If you do not have the brake pads replaced, they will screech all the time. It is normal for the brakes to occasionally squeal or squeak when you apply them.
127
０４／０７／１６ １３：１６：４７ ３１Ｓ５Ｔ６３０ ０１３１
Anti-lock Brakes (ABS)
The Anti-lock Brake System (ABS) helps prevent the brakes from locking up and helps you retain steering control by pumping the brakes rapidly, much faster than a person can do it.
Youshouldneverpumpthebrakepedal. Let the ABS work for you by always keeping firm, steady pressure on the brake pedal. This is sometimes referred to as ‘‘stomp and steer.’’
You will feel a pulsation in the brake pedal when the ABS activates, and you may hear some noise. This is normal: it is the ABS rapidly pumping the brakes. On dry pavement, you will need to press on the brake pedal very hard before the ABS activates. However, you may feel the ABS activate immediately if you are trying to stop on snow or ice.
128
ABS Indicator
ABS INDICATOR
If the ABS indicator comes on, the anti-lock function of the braking system has shut down. The brakes still work like a conventional system, but without anti-lock. You should have a dealer inspect your vehicle as soon as possible.
If the ABS indicator comes on while driving, test the brakes as shown on page
127
Important Safety Reminders ABS does not reduce the time or distance it takes to stop the vehicle; control during braking.
It only helps with steering
ABS will not prevent a skid that results from changing direction abruptly, such as trying to take a corner too fast or making a sudden lane change.
ABS cannot prevent a loss of stability. Always steer moderately when you are braking hard. Severe or sharp steering wheel movement can still cause your vehicle to veer into oncoming traffic or off the road.
A vehicle with ABS may require a longer distance to stop on loose or uneven surfaces, such as gravel or snow, than a vehicle without anti- lock.
０４／０７／１６ １３：１６：５４ ３１Ｓ５Ｔ６３０ ０１３２
Maintenance
This section explains why it is important to keep your vehicle well maintained and how to follow basic maintenance safety precautions.
This section also includes Maintenance Schedules for normal driving and severe driving conditions, a Maintenance Record, and instruc- tions for simple maintenance tasks you may want to take care of yourself.
If you have the skills and tools to per- form more complex maintenance tasks on your vehicle, you may want to purchase the Service Manual. See page for information on how to obtain a copy, or see your dealer.
205
Maintenance Safety Maintenance Schedule Maintenance Record Fluid Locations Adding Engine Oil Changing the Oil and Filter Engine Coolant Windshield Washers Transmission Fluid Brake Fluid Clutch Fluid Lights Cleaning the Seat Belts Floor Mats Dust and Pollen Filter Wiper Blades Tires Checking the Battery Vehicle Storage
...................... ................. .................... .............................. ........................ ......... .............................. .................... ....................... .................................... ................................... ............................................. ................ ..................................... .................. ................................. ............................................... ................... .............................
. 130
. 131
. 135
. 137
. 138
. 139
. 141
. 142
. 143
. 144
. 144
. 145
. 153
. 153
. 153
. 154
. 157
. 162
. 163129
０４／０７／１６ １３：１７：０８ ３１Ｓ５Ｔ６３０ ０１３３
Maintenance Safety
All service items not detailed in this section should be performed by a certified technician or qualified mechanic.
Important Safety Precautions To eliminate potential hazards, read the instructions before you begin, and make sure you have the tools and skills required.
Make sure your vehicle is parked on level ground, the parking brake is set, and the engine is off.
To clean parts, use a commercially available degreaser or parts cleaner, not gasoline.
To reduce the possibility of fire or explosion, keep cigarettes, sparks, and flames away from the battery and all fuel-related parts.
Wear eye protection and protective clothing when working
130
with the battery or compressed air.
Injury from moving parts. not run the engine unless instructed to do so.
Do
Improperly maintaining this vehicle or failing to correct a problem before driving can cause a crash in which you can be seriously hurt or killed.
Always follow the inspection and maintenance recommendations, and schedules in this owner’s manual.
Potential Vehicle Hazards
Carbon Monoxide poison from engine exhaust. Be sure there is adequate ventilation whenever you operate the engine.
Burns from hot parts. Let the engine and exhaust system cool before touching any parts.
Failure to properly follow maintenance instructions and precautions can cause you to be seriously hurt or killed.
Always follow the procedures and precautions in this owner’s manual.
Some of the most important safety precautions are given here. However, we cannot warn you of every conceivable hazard that can arise in performing maintenance. Only you can decide whether or not you should perform a given task.
０４／０７／１６ １３：１７：２２ ３１Ｓ５Ｔ６３０ ０１３４
The maintenance schedule assumes you will use your vehicle as normal transportation for passengers and their possessions. You should also follow these recommendations:
Which Schedule to Follow Service your vehicle according to the time and mileage periods on one of the Maintenance Schedules on the following pages.
Driving with a roof rack, or driving in mountainous conditions.
Driving on muddy, dusty, or de- iced roads.
Maintenance Schedule
Avoid exceeding your vehicle’s load limit. This puts excess stress on the engine, brakes, and many other vehicle parts. The load limit is shown on the tire information label on the driver’s doorjamb.
Operate your vehicle on reasonable roads within the legal speed limit.
Drive your vehicle regularly over a distance of several miles (kilometers).
Always use unleaded gasoline with the proper octane rating (see page 110
).
−
Follow the
U.S. Owners Maintenance Schedule for Severe Conditions if you drive your vehicle MAINLY under one or more of the following conditions.
OCCASIONALLY
NOTE: If you only under a ‘‘severe’’ condition, you should follow the Normal Conditions Maintenance Schedule.
drive
Canadian Owners Follow the Maintenance Schedule for Severe Conditions.
−
Driving less than 5 miles (8 km) per trip or, in freezing temperatures, driving less than 10
miles (16 km) per trip.Driving in extremely hot [over 90°F (32°C)] conditions.
Used primarily as a delivery vehicle or taxi that is driven mostly in stop-and-go traffic and/ or parked with the engine idling.
131
０４／０７／１６ １３：１７：３６ ３１Ｓ５Ｔ６３０ ０１３５
Maintenance Schedule
Servicing Your Vehicle Your authorized dealer knows your vehicle best and can provide competent, efficient service. However, service at a dealer is not mandatory to keep your warranties in effect. Maintenance may be done by any qualified service facility or skilled person to keep your warranties in effect. Keep all the receipts as proof of completion, and have the person who does the work fill out the Maintenance Record. Check your warranty booklet for more information.
We recommend the use of Honda parts and fluids whenever you have maintenance done.
U.S. Vehicles: Maintenance, replacement, or repair of emissions control devices and systems may be done by any automotive repair establishment or individual using parts that are ‘‘certified’’ to EPA standards.
＃
According to state and federal regulations, failure to perform maintenance on the items marked with will not void your emissions warranties. However, all maintenance services should be performed at the recommended time or mileage period to ensure long- term reliability.
132
Owner’s Maintenance Checks You should check the following items at the specified intervals. If you are unsure of how to perform any check, turn to the appropriate page listed.
−
−
−
114
113
Check the
Check every
Engine oil level time you fill the fuel tank. See page Engine coolant level radiator reserve tank every time you fill the fuel tank. See page Brakes Check the fluid level monthly. See page Tires Check the tire pressure monthly. Examine the tread for wear and foreign objects. See page 157
Lights the headlights, parking lights, taillights, high-mount brake light, turn signals, and license plate 145
lights monthly. See pageCheck the operation of
144
−
−
０４／０７／１６ １３：１８：０１ ３１Ｓ５Ｔ６３０ ０１３６
Service the items listed at the indicated distance (or time, if given). 90
144miles x 1,000
km x 1,00080
12810
1620
3230
4850
8040
120
64
192
Check oil and coolant at each fuel stop70
112100
160110
17660
96130
208140
224150
240Check engine oil and coolant Check tires Replace engine oil
Rotate tires (follow pattern on page 160) Replace engine oil filter Check front and rear brakes Check parking brake adjustment Inspect the following items:
Tie rod ends, steering gear box, and boots Suspension components Driveshaft boots Brake hoses and lines (including ABS) All fluid levels and condition of fluids Exhaust system ＃ Fuel lines and connections
＃
Inspect drive belts Replace Dust and Pollen Filter Replace air cleaner element Replace spark plugs Inspect valve clearance
Replace manual transmission fluid
Inspect idle speed Replace engine coolant
Replace brake fluid
Check inflation and condition once a month
((OOrreevveerryy11yyeeaarr,,wwhhiicchheevveerrccoommeessffiirrsstt))
Every 10,000 miles (16,000 km)
((OOrreevveerryy11yyeeaarr,,wwhhiicchheevveerrccoommeessffiirrsstt))
((OOrreevveerryy22yyeeaarrss,,wwhhiicchheevveerrccoommeessffiirrsstt))
((OOtthheerrwwiisseeaaddjjuussttoonnllyyiiffnnooiissyy))
((OOrreevveerryy66yyeeaarrss,,wwhhiicchheevveerrccoommeessffiirrsstt))
Every 160,000 miles (256,000 km)
120,000 miles (192,000 km) or 10 years, then every
60,000 miles (96,000 km) or 5 years
Every 3 years (independent of mileage)
＃
See information on maintenance and emissions warranty on page
132
Follow the Normal Maintenance Schedule if the severe driving conditions specified in the Severe Conditions Maintenance Schedule on the next page do not apply.
NOTE: If you only OCCASIONALLY drive under a ‘‘severe’’ condition, you should follow the Normal Conditions Maintenance Schedule.
133
０４／０７／１６ １３：１８：３３ ３１Ｓ５Ｔ６３０ ０１３７
Service the items listed at the indicated distance (or time, if given). 90
144miles x 1,000
km x 1,00070
11210
1620
3230
4860
9650
8040
120
64
192
Check oil and coolant at each fuel stop110
17680
128100
160130
208140
224150
240Check engine oil and coolant Check tires Replace engine oil
Rotate tires (follow pattern on page 160) Replace engine oil filter Check front and rear brakes Lubricate all hinges, locks, and latches Inspect the following items:
Tie rod ends, steering gear box and boots Suspension components, Driveshaft boots
Check parking brake adjustment Inspect the following items:
Brake hoses and lines (including ABS) All fluid levels and condition of fluids Exhaust system , Fuel lines and connections Lights and controls/vehicle underbody
＃
＃
Inspect drive belts Replace Dust and Pollen Filter Replace air cleaner element
＊
Replace spark plugs Inspect valve clearance
Replace manual transmission fluid
Inspect idle speed Replace engine coolant
Replace brake fluid
134
Check inflation and condition once a month
Every 5,000 miles (8,000 km) or every 6 months,
whichever comes first
Every 10,000 miles (16,000 km)
((OOrreevveerryy11yyeeaarr,,wwhhiicchheevveerrccoommeessffiirrsstt))
((OOrreevveerryy11yyeeaarr,,wwhhiicchheevveerrccoommeessffiirrsstt))
((OOrreevveerryy22yyeeaarrss,,wwhhiicchheevveerrccoommeessffiirrsstt))
Every 15,000 miles (24,000 km) (Use normal schedule
except in dusty conditions)
Follow the Severe Maintenance Schedule if you drive your vehicle MAINLY under one or more of the following conditions:
Driving less than 5 miles (8 km) per trip or, in freezing temperatures, driving less than 10 miles (16 km) per trip. Driving in extremely hot [over 90°F (32°C)] conditions. Extensive idling or long periods of stop and go driving, such as a taxi or a commercial delivery vehicle. Driving with a roof rack, or driving in mountainous conditions. Driving on muddy, dusty, or de-iced roads.
−
Canadian Owners Follow the Maintenance Schedule for Severe Conditions. ＃
See information on maintenance and emissions warranty on page
132
((OOtthheerrwwiisseeaaddjjuussttoonnllyyiiffnnooiissyy))
＊
((OOrreevveerryy33yyeeaarrss,,wwhhiicchheevveerrccoommeessffiirrsstt))
Every 160,000 miles (256,000 km)
120,000 miles (192,000 km) or 10 years, then every
60,000 miles (96,000 km) or 5 years
Every 3 years (independent of mileage)
See dust and pollen filter on page replacement information under special driving conditions.
153
for
０４／０７／１６ １３：１８：４２ ３１Ｓ５Ｔ６３０ ０１３８
Maintenance Record
(forNormalandSevereSchedules)
You or the servicing dealer can record all completed maintenance here, whether you follow the schedule for normal conditions (page conditions (page
). Keep the receipts for all work done on your vehicle.
134
133
) or severe
5,000 mi 8,000 km
10,000 mi 16,000 km
15,000 mi 24,000 km
20,000 mi 32,000 km (or 1 year)
25,000 mi 40,000 km
30,000 mi 48,000 km
35,000 mi 56,000 km
40,000 mi 64,000 km (or 2 years)
Signature or dealer stamp
mi/km
Date
mi/km
Date
mi/km
Date
mi/km
Date
mi/km
Date
mi/km
Date
mi/km
Date
mi/km
Date
45,000 mi 72,000 km
50,000 mi 80,000 km
55,000 mi 88,000 km
60,000 mi 96,000 km (or 3 years)
65,000 mi 104,000 km
70,000 mi 112,000 km
75,000 mi 120,000 km
80,000 mi 128,000 km (or 4 years)
Signature or dealer stamp mi/km
Date
mi/km
Date
mi/km
Date
mi/km
Date
mi/km
Date
mi/km
Date
mi/km
Date
mi/km
Date
CONTINUED 135
０４／０７／１６ １３：１８：４９ ３１Ｓ５Ｔ６３０ ０１３９
Maintenance Record
(forNormalandSevereSchedules)
Signature or dealer stamp
mi/km
Date
mi/km
Date
mi/km
Date
mi/km
Date
mi/km
Date
mi/km
Date
mi/km
Date
mi/km
Date
85,000 mi 136,000 km
90,000 mi 144,000 km
95,000 mi 152,000 km
100,000 mi 160,000 km (or 5 years)
105,000 mi 168,000 km
110,000 mi 176,000 km
115,000 mi 184,000 km
120,000 mi 192,000 km (or 6 years)
136
125,000 mi 200,000 km
130,000 mi 208,000 km
135,000 mi 216,000 km
140,000 mi 224,000 km (or 7 years)
145,000 mi 232,000 km
150,000 mi 240,000 km
155,000 mi 248,000 km
160,000 mi 256,000 km (or 8 years)
Signature or dealer stamp
mi/km
Date
mi/km
Date
mi/km
Date
mi/km
Date
mi/km
Date
mi/km
Date
mi/km
Date
mi/km
Date
０４／０７／１６ １３：１８：５４ ３１Ｓ５Ｔ６３０ ０１４０
ENGINE OIL DIPSTICK (Orange handle)
WASHER FLUID (Blue cap)
ENGINE COOLANT RESERVOIR
RADIATOR CAP
Fluid Locations
BRAKE FLUID (Gray cap)
CLUTCH FLUID (Gray cap)
ENGINE OIL FILL CAP
137
０４／０７／１６ １３：１９：０３ ３１Ｓ５Ｔ６３０ ０１４１
Adding Engine Oil
Recommended Engine Oil Oil is a major contributor to your engine’s performance and longevity. Always use a premium-grade 5W-20
detergent oil displaying the API Certification Seal. This seal indicates the oil is energy conserving, and that it meets the American Petroleum Institute’s latest requirements.Honda Motor Oil is the preferred 5W-20 lubricant for your vehicle. It is highly recommended that you use Honda Motor Oil in your vehicle for optimum engine protection. Make sure the API Certification Seal says ‘‘For Gasoline Engines.’’
The oil’s viscosity or weight is provided on the container’s label. 5W-20 oil is formulated for year- round protection of your vehicle, to improve cold weather starting and fuel economy.
API SERVICE LABEL
Ambient Temperature
ENGINE OIL FILL CAP
Unscrew and remove the engine oil fill cap on top of the valve cover. Pour in the oil slowly and carefully so you do not spill. Clean up any spills immediately. Spilled oil could damage components in the engine compartment. Install the engine oil fill cap, and tighten it securely. Wait a few minutes, and recheck the oil level. Do not fill above the upper mark; you could damage the engine.
138
０４／０７／１６ １３：１９：１５ ３１Ｓ５Ｔ６３０ ０１４２
Adding Engine Oil, Changing the Oil and Filter
Synthetic Oil You may use a synthetic motor oil if it meets the same requirements given for a conventional motor oil: it displays the API Certification Seal, and it is the proper weight. You must follow the oil and filter change intervals given on the maintenance schedule.
Engine Oil Additives Your vehicle does not require any oil additives. Additives may adversely affect your engine’s or transmission’s performance and durability.
Changing the Oil and Filter Always change the oil and filter according to the recommendations in the maintenance schedule. The oil and filter collect contaminants that can damage your engine if they are not removed regularly.
Changing the oil and filter requires special tools and access from underneath the vehicle. The vehicle should be raised on a service station- type hydraulic lift for this service. Unless you have the knowledge and proper equipment, you should have this maintenance done by a skilled mechanic.
1.
2.
OIL DRAIN BOLT
WASHER
Run the engine until it reaches normal operating temperature, then shut it off.
Open the hood and remove the engine oil fill cap. Remove the oil drain bolt and washer from the bottom of the engine. Drain the oil into an appropriate container.
CONTINUED
139
０４／０７／１６ １３：１９：２７ ３１Ｓ５Ｔ６３０ ０１４３
5.
Put a new washer on the drain bolt, then reinstall the drain bolt. Tighten it to: 33 lbf·ft (44 N·m , 4.5 kgf·m)
6.
Refill the engine with the recommended oil.
Engine oil change capacity (including filter): 4.4 US qt (4.2 )
7.
Replace the engine oil fill cap. Start the engine. The oil pressure indicator should go out within 5
seconds. If it does not, turn off the engine, and check your work.8.
9.
Let the engine run for several minutes, then check the drain bolt and oil filter for leaks.
Turn off the engine, let it sit for several minutes, then check the oil level on the dipstick. If necessary, add more oil.
Improper disposal of engine oil can be harmf ul to the environment. If you change your own oil, please dispose of the used oil properly. Put it in a sealed container and take it to a recycling center. Do not discard it in a trash bin or dump it on the ground.
Changing the Oil and Filter
OIL FILTER
3.
Remove the oil filter, and let the remaining oil drain. A special wrench (available from your dealer) is required.
4.
Install a new oil filter according to the instructions that come with it.
140
０４／０７／１６ １３：１９：３５ ３１Ｓ５Ｔ６３０ ０１４４
Adding Engine Coolant
RESERVE TANK
If the coolant level in the reserve tank is at or below the MIN line, add coolant to bring it up to between the MIN and MAX lines. Inspect the cooling system for leaks.
Always use Honda All Season Antifreeze/Coolant Type 2. This coolant is pre-mixed with 50 percent antifreeze and 50 percent water. Never add straight antifreeze or plain water.
Engine Coolant
If Honda antifreeze/coolant is not available, you may use another major-brand non-silicate coolant as a temporary replacement. Make sure it is a high-quality coolant recommended for aluminum engines. Continued use of any non-Honda coolant can result in corrosion, causing the cooling system to malfunction or fail. Have the cooling system flushed and refilled with Honda antifreeze/coolant as soon as possible.
If the reserve tank is completely empty, you should also check the coolant level in the radiator.
Removing the radiator cap while the engine is hot can cause the coolant to spray out, seriously scalding you.
Always let the engine and radiator cool down before removing the radiator cap.
CONTINUED
141
０４／０７／１６ １３：１９：４８ ３１Ｓ５Ｔ６３０ ０１４５
Engine Coolant, Windshield Washers
RADIATOR CAP
1.
When the radiator and engine are cool, relieve any pressure in the cooling system by turning the radiator cap counterclockwise, without pressing down.
2.
Remove the radiator cap by pushing down and turning counterclockwise.
142
3.
