Login- Download PDF Manual
-
you will hear a beep to verify that the doors are locked. You cannot lock it if any door is not fully closed or the key is in the ignition switch.
−
Press this button once
UNLOCK to unlock the driver’s door. Push it twice to unlock the other doors and hatch. Some exterior and interior lights flash twice each time you press this button. If you do not open any doors within 30 seconds, they will automatically relock.
−
Press this button for
PANIC about 1 second to attract attention; the horn will sound and the exterior lights will flash for about 30 seconds. To cancel panic mode, press any other button on the remote transmitter, or turn the ignition switch to ON (II).
Remote Transmitter
RemoteTransmitterCare
Avoid dropping or throwing the transmitter. Protect the transmitter from extreme temperature. Do not immerse the transmitter in any liquid. If you lose a transmitter, the replacement needs to be reprogrammed by your dealer.
69
０４／０７／１６ １３：０８：０４ ３１Ｓ５Ｔ６３０ ００７３
Remote Transmitter
Replacing the Transmitter Battery
ROUND COVER
CUSHION RING
BATTERY
If it takes several pushes on the button to lock or unlock the doors and the hatch, replace the battery as soon as possible. Battery type: CR2025
70
To replace the battery, remove the round cover on the back of the transmitter by turning it counterclockwise with a coin. Insert a new battery with the side facing up. Align the mark on the cover with the ◎ transmitter. Set the cover in place, and turn it clockwise.
▽ mark on the
＋
AsrequiredbytheFCC: ThisdevicecomplieswithPart15ofthe FCCrules.Operationissubjecttothe followingtwoconditions:(1)Thisdevice maynotcauseharmfulinterference,and (2)thisdevicemustacceptany interferencereceived,including interferencethatmaycauseundesired operation.
Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser’s authoritytooperatetheequipment.
ThisdevicecomplieswithIndustry CanadaStandardRSS-210. Operationissubjecttothefollowingtwo conditions:(1)thisdevicemaynotcause interference,and(2)thisdevicemust acceptanyinterferencethatmaycause undesiredoperationofthedevice.
０４／０７／１６ １３：０８：１２ ３１Ｓ５Ｔ６３０ ００７４
Seats
Front Seat Adjustments Seepages forimportantsafety informationandwarningsabouthowto properlypositionseatsandseat-backs.
14
12
−
Make all seat adjustments before you start driving.
To adjust the seat forward and backward, pull up on the bar under the seat cushion’s front edge. Then try to move the seat to make sure it is locked in position.
To change the seat-back angle of the front seat, pull up on the lever on the outside of the seat bottom.
71
０４／０７／１６ １３：０８：２２ ３１Ｓ５Ｔ６３０ ００７５
Seats
Head Restraints Seepage forimportantsafety informationandawarningabouthowto properlypositiontheheadrestraints.
15
RELEASE BUTTON
Your vehicle is equipped with head restraints in the rear outboard seating positions.
72
The head restraints help protect you and your passengers from whiplash and other injuries. They are most effective when you adjust them so the back of the occupant’s head rests against the center of the restraint.
The head restraints in the rear outboard seating positions adjust for height. You need both hands to adjust the restraint. To raise it, pull upward. To lower the restraint, push the release button sideways and push the restraint down.
Rear Seat Access
To get into the rear seat on the driver’s side, pull up on the seat-back adjustment lever.
To get into the rear seat on the passenger’s side, push down on the release lever at the base of the seat- back. The seat-back will tilt forward, and the seat will slide forward to allow easier access to the rear seat.
０４／０７／１６ １３：０８：２８ ３１Ｓ５Ｔ６３０ ００７６
After you return the seat-back to the upright position, push the whole seat backwards until it latches. Make sure the seat is fully latched before you sit in it.
Folding Rear Seat The back of the rear seat folds down to give you more cargo space. Each side folds down separately. With only half the seat folded, you can still carry a passenger in the back seat.
Seats
CLIP
Before folding down the seat-back, move the seat belt out of the way and put the shoulder part of the outside seat belt in the clip on each side.
73
０４／０７／１６ １３：０８：３６ ３１Ｓ５Ｔ６３０ ００７７
Seats
RELEASE LEVER
Make sure all items in the cargo area are secured. Loose items can fly forward and cause injury if you have Carrying Cargo to brake hard. See on page
117
Never drive with the seat-back folded down and the hatch open. See Carbon Monoxide Hazard on page 47
To lock the seat-back upright, push it firmly against its latch. Tug on the seat-back to make sure it is latched.
Make sure the seat belts are positioned in front of the rear seat- back and the seat belt buckles are on the seat cushion whenever the seat- back is in its upright position.
To unlatch either side of the seat- back, pull up on the release lever, then fold the seat-back down.
74
０４／０７／１６ １３：０８：４３ ３１Ｓ５Ｔ６３０ ００７８
HOOK
NOTCHES
The cargo area cover may be removed to give you more cargo room.
To remove the cargo area cover, disconnect the cables from the hatch by lifting up each end, then pulling it outward. Then push up on the underside of the cargo cover at each front corner to unsnap it from the body.
To install the cargo area cover, place it in its normal position over the cargo area. Then push down on each front corner to snap it in place. Lift up the rear of the cover, then reconnect the cables to the hatch.
Cargo Area Cover
75
０４／０７／１６ １３：０８：４９ ３１Ｓ５Ｔ６３０ ００７９
Power Windows
Your vehicle’s windows are electri- cally-powered. Turn the ignition switch to ON (II) to raise or lower any window.
Each door has a switch that controls its window. To open the window, push the switch down and hold it. Release the switch when you want the window to stop. Close the window by pulling back on the switch and holding it.
76
Closing a power window on someone’s hands or fingers can cause serious injury.
Make sure your passenger is away from the window before closing it.
DRIVER’S WINDOW SWITCH
MAIN SWITCH
The driver’s door armrest has a master power window control panel. To open the passenger’s window, push down on the appropriate switch and hold it until the window reaches the desired position. To close the window, pull back on the window switch. Release the switch when the window gets to the position you want.
０４／０７／１６ １３：０８：５７ ３１Ｓ５Ｔ６３０ ００８０
−
To open or close the
AUTO driver’s window, push or pull the window switch firmly down or up to the second detent, and release it. The window will automatically go up or down all the way. To stop the window, pull or push on the window switch briefly.
If the MAIN switch is OFF, the passenger window cannot be raised or lowered. Keep the MAIN switch off when you have children in the vehicle so they do not injure themselves by operating the window unintentionally.
−
AUTO REVERSE If the driver’s window senses any obstacle while it is closing automatically, it will reverse direction and then stop. To close the window, remove the obstacle, then use the window switch again.
If your vehicle’s battery is disconnected or goes dead, or the driver’s window fuse is removed, the AUTO function will be disabled. The power window system needs to be reset after reconnecting the battery or installing the fuse.
1.
2.
Start the engine. Push down and hold the driver’s window switch until the window is fully open.
Pull and hold the driver’s window switch to close the window completely, then hold the switch for a second or two more.
Power Windows
If the power windows do not operate properly after resetting, have your vehicle checked by your dealer.
77
０４／０７／１６ １３：０９：０６ ３１Ｓ５Ｔ６３０ ００８１
Moonroof
OPEN/CLOSE SWITCH
To open the moonroof, pull back the moonroof switch firmly.
To close the moonroof fully, push the switch forward.
To tilt the moonroof up, press the button in. To close it, push the switch forward.
The moonroof will not close completely; it will stop about 5.1
inches (130 mm) away from being closed. Make sure your passengers are clear of the moonroof, then release the switch and push it forward again to close the moonroof completely.TILT-UP BUTTON
There are two switches on the ceiling near the front ceiling light. The ignition switch must be in the ON (II) position to operate the moonroof.
78
Opening or closing the moonroof on someone’s hands or fingers can cause serious injury.
Make sure all hands and fingers are clear of the moonroof before opening or closing it.
If you try to open the moonroof in below-f reezing temperatures, or when it is covered with snow or ice, you can damage the moonroof panel or motor.
０４／０７／１６ １３：０９：１５ ３１Ｓ５Ｔ６３０ ００８２
Mirrors
AdjustingthePowerMirrors
SELECTOR SWITCH
ADJUSTMENT SWITCH 1.
Move the selector switch to L (driver’s side) or R (passenger’s side).
TAB
Keep the inside and outside mirrors clean and adjusted for best visibility. Be sure to adjust the mirrors before you start driving.
The inside mirror has day and night positions. The night position reduces glare from headlights behind you. Flip the tab on the bottom edge of the mirror to select the day or night position.
Mirrors
2.
3.
Push the appropriate edge of the adjustment switch to move the mirror right, left, up, or down.
When you finish, move the selector switch to the center (off) position. This turns the adjustment switch off to keep your settings.
79
０４／０７／１６ １３：０９：２４ ３１Ｓ５Ｔ６３０ ００８３
Mirrors, Parking Brake
Power Mirror Heaters
Parking Brake
HEATED MIRROR BUTTON
PARKING BRAKE LEVER
Driving the vehicle with the parking brake applied can damage the rear brakes and axles.
To apply the parking brake, pull the lever up fully. To release it, pull up slightly, push the button, and lower the lever. The parking brake indicator on the instrument panel should go out when the parking brake is fully released (see page
53
).
Canadianmodelonly The outside mirrors are heated to remove fog and frost. With the ignition switch in the ON (II) position, turn on the heaters by pressing the button. The indicator in the button comes on as a reminder. Press the button again to turn the heaters off.
80
０４／０７／１６ １３：０９：３２ ３１Ｓ５Ｔ６３０ ００８４
Ceiling Light
FRONT
DOOR ACTIVATED
The front ceiling light also contains two spotlights. Push the button next to the light to turn it on and off.
Cargo Area Light The cargo area light comes on when you open the hatch.
Interior Lights
OFF
ON
The ceiling light has a three-position switch: ON, Door Activated, and OFF. In the Door Activated (center) position, the light comes on when you:
Open any door. Remove the key from the ignition. If you do not open a door, the light fades out in about 10 seconds. Unlock the doors with the key or remote transmitter.
81
０４／０７／１６ １３：０９：３７ ３１Ｓ５Ｔ６３０ ００８５
Interior Convenience Items
COAT HOOK
BEVERAGE HOLDER
VANITY MIRROR
DRIVER’S POCKET
ACCESSORY POWER SOCKET
GLOVE BOX
BEVERAGE HOLDER
BEVERAGE HOLDER
CONSOLE COMPARTMENT
82
０４／０７／１６ １３：０９：４７ ３１Ｓ５Ｔ６３０ ００８６
Beverage Holders Be careful when you are using the beverage holders. A spilled liquid that is very hot can scald you or your passengers. Spilled liquids can damage the upholstery, carpeting, and electrical components in the interior.
Accessory Power Socket This socket is intended to supply power for 12 volt DC accessories that are rated 120 watts or less (10
amps). It will not power an automotive type cigarette lighter element.Interior Convenience Items
Glove Box Open the glove box by squeezing the handle. Close it with a firm push.
Console Compartment
CONSOLE COMPARTMENT
An open glove box can cause serious injury to your passenger in a crash, even if the passenger is wearing the seat belt.
Always keep the glove box closed while driving.
BEVERAGE HOLDER
To access the console compartment, slide the lid forward, then slide the beverage holder assembly forward.
83
０４／０７／１６ １３：０９：５６ ３１Ｓ５Ｔ６３０ ００８８
Features
The heating and air conditioning systems in your vehicle provide a comfortable driving environment in all weather conditions.
The standard audio system has many features. This section de- scribes those features and how to use them. (If you selected an optional audio system, refer to the operating instructions that came with it.)
Your vehicle has an anti-theft audio system that requires a code number to enable it.
Air Flow Controls
Vents, Heating, and A/C
............... ....................... ............................ .............................. .................................... ..................................... ...................... ........... ....... ............................... ................. .......................... ...............................
Playing the Radio Radio Reception Playing a CD CD Changer Protecting Your CDs CD Player Error Messages CD Changer Error Messages Playing a Tape Radio Theft Protection Setting the Clock Cruise Control
. 86
. 87
. 90
. 93
. 95
. 96
. 97
. 98
. 99
. 100
. 103
. 104
. 10585
０４／０７／１６ １３：１０：００ ３１Ｓ５Ｔ６３０ ００８９
Vents, Heating, and A/C
RECIRCULATION BUTTON
AIR CONDITIONING (A/C) BUTTON
MODE CONTROL DIAL
TEMPERATURE CONTROL DIAL
FAN CONTROL DIAL
86
REAR WINDOW DEFOGGER BUTTON
０４／０７／１６ １３：１０：２０ ３１Ｓ５Ｔ６３０ ００９０
Fan Control Dial Turn this dial to increase or decrease the fan speed and airflow.
Temperature Control Dial Turning this dial clockwise increases the temperature of the airflow.
Air Conditioning (A/C) Button This button turns the air conditioning on and off. The indicator in the button comes on when the A/C is on.
Recirculation Button When the recirculation indicator is on, air from the vehicle’s interior is sent throughout the system again. When the indicator is off, air is brought in from the outside of the vehicle (Fresh Air mode).
The outside air intakes for the heating and cooling system are at the base of the windshield. Keep this area clear of leaves and other debris.
The system should be left in Fresh Air mode under almost all conditions. Keeping the system in Recirculation mode, particularly with the A/C off, can cause the windows to fog up.
Switch to Recirculation mode when driving through dusty or smoky conditions, then return to Fresh Air mode.
Rear Window Defogger Button This button turns the rear window ). defogger off and on (see page 62
Mode Control Dial Use the mode control dial to select the vents the air flows from. Some air will flow from the dashboard vents in all modes.
Air Flow Controls
Air flows from the center and corner vents in the dashboard.
Airflow is divided between the vents in the dashboard and the floor vents.
Air flows from the floor
vents. When you select system automatically switches to Fresh Air mode.
, the
Airflow is divided between
the floor vents and the defroster vents at the base of the windshield.
Air flows from the defroster vents at the base of the windshield.
or
When you select the system automatically switches to Fresh Air mode and turns on the A/C. (The A/C indicator will not come on.)
87
０４／０７／１６ １３：１０：３０ ３１Ｓ５Ｔ６３０ ００９１
you can
Iftheinteriorisverywarm, cool it down more rapidly by partially opening the windows, turning on the A/C, and setting the fan to maximum speed in Fresh Air mode.
Using the A/C Air conditioning places an extra load on the engine. Watch the engine coolant temperature gauge (see page 60
turn off the A/C until the gauge reads normally.). If it moves near the red zone,
1.
2.
3. 4.
5.
Turn on the A/C by pressing the button. The indicator in the button comes on when a fan speed is selected. Make sure the temperature is set to maximum cool. Select If the outside air is humid, select Recirculation mode. If the outside air is dry, select Fresh Air mode. Set the fan to the desired speed.
Vents, Heating, and A/C
Ventilation The flow-through ventilation system draws in outside air, circulates it through the interior, then exhausts it through vents near the rear side panels.
1.
2. 3. 4.
Set the temperature to the lower limit. Make sure the A/C is off. Select Set the fan to the desired speed.
and Fresh Air mode.
Using the Heater The heater uses engine coolant to warm the air. If the engine is cold, it will be several minutes before you feel warm air coming through the system.
1. 2. 3.
and Fresh Air mode.
Select Set the fan to the desired speed. Adjust the warmth of the air with the temperature control dial.
88
０４／０７／１６ １３：１０：４３ ３１Ｓ５Ｔ６３０ ００９２
Dehumidify the Interior Air conditioning, as it cools, removes moisture from the air. When used in combination with the heater, it makes the interior warm and dry.
1. 2. 3. 4.
Turn the fan on. Turn on the air conditioning. Select Adjust the temperature control dial or buttons to your preference.
and Fresh Air mode.
This setting is suitable for all driving conditions whenever the outside temperature is above 32°F (0°C).
To Defog and Defrost To remove fog from the inside of the windows:
1. 2.
3.
4.
5.
. The system
Set the fan to high. Select automatically switches to fresh air mode and turns on the A/C. The A/C indicator will not come on in U.S. vehicles. Adjust the temperature control dial so the airflow feels warm. Select to help clear the rear window. To increase airflow to the windshield, close the corner vents.
When you switch to another mode from Press the A/C button to turn it off.
, the A/C stays on.
Vents, Heating, and A/C
To Remove Exterior Frost or Ice From the Windows
1.
2. 3.
. The system
Select automatically switches to Fresh Air mode and turns on the A/C. The A/C indicator will not come on in U.S. vehicles. Select Set the fan and temperature controls to maximum level.
To clear the windows faster, you can close the dashboard corner vents by rotating the wheel below each vent. This sends more warm air to the windshield defroster vents. Once the windshield is clear, select Fresh Air mode to avoid fogging the windows.
For your safety, make sure you have a clear view through all the windows before driving.
89
０４／０７／１６ １３：１０：４８ ３１Ｓ５Ｔ６３０ ００９３
Playing the Radio
AM/FM BUTTON
SCAN INDICATOR
STEREO INDICATOR
AUTO SELECT BUTTON
SCAN BUTTON
POWER/VOLUME KNOB
TUNE KNOB
SEEK BAR
PRESET BUTTONS
90
０４／０７／１６ １３：１１：０１ ３１Ｓ５Ｔ６３０ ００９４
Playing the Radio
To Play the Radio The ignition switch must be in the ACCESSORY (I) or ON (II) position. Turn the system on by pushing the PWR/VOL knob or the AM/FM button. Adjust the volume by turning the PWR/VOL knob.
The band and frequency that the radio was last tuned to is displayed. To change bands, press the AM/FM button. On the FM band, ST will be displayed if the station is broadcast- ing in stereo. Stereo reproduction on AM is not available.
To Select a Station You can use these five methods to find radio stations on a selected band: preset buttons, and
TUNE, SEEK, SCAN,
AUTO SELECT
the
−
Use the TUNE knob to
TUNE tune the radio to a desired frequency. Turn the knob right to tune to a higher frequency, or left to tune to a
lower frequency.
−
The SEEK function
SEEK searches up and down from the current frequency to find a station with a strong signal. To activate it, press the side of the bar, then release it.
or
−
The SCAN function
SCAN samples all stations with strong signals on the selected band. To activate it, press the SCAN button, then release it. You will see SCAN in the display. The system will scan for a station with a strong signal. When it finds one, it will stop and play that station for about 5 seconds.
If you do nothing, the system will scan for the next strong station and play it for 5 seconds. When it plays a station you want to listen to, press the SCAN button again.
−
Each preset button can
Preset store one frequency on AM, and two frequencies on FM.
1.
2.
3.
4.
Select the desired band, AM or FM. FM1 and FM2 let you store two frequencies with each preset button. Use the TUNE, SEEK, or SCAN function to tune the radio to a desired station. Pick a preset button, and hold it until you hear a beep. Repeat steps 1 through 3 to store a total of six stations on AM and twelve stations on FM.
The preset frequencies will be lost if your vehicle’s battery goes dead, is disconnected, or the radio fuse is removed.
91
０４／０７／１６ １３：１１：１５ ３１Ｓ５Ｔ６３０ ００９５
Playing the Radio
press the ToturnoffAutoSelect, A. SEL button. This restores the presets you originally set.
Adjusting the Sound Press the SOUND/TUNE knob repeatedly to display the Bass (BAS), Treble (TRE), Fader (FAD), and Balance (BAL) setting.
Each mode is shown in the display as it changes. Turn the SOUND/TUNE knob to adjust the setting to your liking. When the level reaches the center, you will see ‘‘C’’ in the display. The system will automatically return the display to the selected audio mode about 5 seconds after you stop adjusting a mode.
−
BAL to-side strength of the sound.
Adjust the Balance, or side-
−
FAD front-to-back strength of the sound.
Adjust the Fader, or the
TRE − sound.
Adjust the Treble in the
BAS
−
Adjust the Bass in the sound.
Audio System Lighting You can use the instrument panel brightness control knob to adjust the illumination of the audio system (see page illuminates when the parking lights are on, even if the radio is turned off.
). The audio system
62
−
If you are
AUTO SELECT traveling far from home and can no longer receive your preset stations, you can use the Auto Select feature to find stations in the local area.
Press the A. SEL button. ‘‘A.SEL’’ flashes in the display, and the system goes into scan mode for several seconds. It stores the frequencies of six AM, and twelve FM stations in the preset buttons.
You will see a ‘‘0’’ displayed after pressing a preset button if Auto Select cannot find a strong station for every preset button.
If you do not like the stations Auto Select has stored, you can store other frequencies on the preset buttons as previously described.
92
０４／０７／１６ １３：１１：２８ ３１Ｓ５Ｔ６３０ ００９６
Radio Reception How well the radio receives stations is dependent on many factors, such as the distance from the station’s transmitter, nearby large objects, and atmospheric conditions.
A radio station’s signal gets weaker as you get farther away from its transmitter. If you are listening to an AM station, you will notice the sound volume becoming weaker and the station drifting in and out. If you are listening to an FM station, you will see the stereo indicator flickering off and on as the signal weakens. Eventually, the stereo indicator will go off and the sound will fade completely as you get out of range of the station’s signal.
Radio Frequencies The radio can receive the complete AM and FM bands. Those bands cover these frequen- cies:
AM band: 530 to 1,710 kilohertz
FM band: 87.7 to 107.9 megahertz
Radio stations on the AM band are assigned frequencies at least ten kilohertz apart (530, 540, 550). Stations on the FM band are assigned frequencies at least 0.2
megahertz apart (87.9, 88.1, 88.3).Stations must use these exact frequencies. It is fairly common for stations to round-off the frequency in their advertising, so your radio could display a frequency of 100.9 even though the announcer may identify the station as ‘‘FM101.’’
Radio Reception
Driving very near the transmitter of a station that is broadcasting on a frequency close to the frequency of the station you are listening to can also affect your radio’s reception. You may temporarily hear both stations, or hear only the station you are close to.
93
０４／０７／１６ １３：１１：３５ ３１Ｓ５Ｔ６３０ ００９７
Radio Reception
AsrequiredbytheFCC: Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser’s authoritytooperatetheequipment.
Radio signals, especially on the FM band, are deflected by large objects such as buildings and hills. Your radio then receives both the direct signal from the station’s transmitter, and the deflected signal. This causes the sound to distort or flutter. This is a main cause of poor radio reception in city driving.
Radio reception can be affected by atmospheric conditions such as thunderstorms, high humidity, and even sunspots. You may be able to receive a distant radio station one day and not receive it the next day because of a change in conditions.
Electrical interference from passing vehicles and stationary sources can cause temporary reception problems.
94
０４／０７／１６ １３：１１：４０ ３１Ｓ５Ｔ６３０ ００９８
Playing a CD
CD BUTTON
REPEAT INDICATOR
RANDOM BUTTON
CD SLOT
CD EJECT BUTTON
POWER/VOLUME KNOB
RANDOM INDICATOR
SEEK/SKIP BAR
SCAN/REPEAT BUTTON
95
０４／０７／１６ １３：１１：５４ ３１Ｓ５Ｔ６３０ ００９９
Playing a CD, CD Changer
To Play a CD With the ignition switch in the ACCESSORY (I) or ON (II) position, insert a CD into the CD slot. The drive will pull the CD in the rest of the way and begin to play it. The number of the track playing is shown in the display. The system will continuously play a CD until you change modes.
−
, the player skips
Each time you press and
SKIP release forward to the beginning of the next track. Press and release to skip backward to the beginning of the previous track. To move rapidly within a track, press and hold the see CUE or REW in the display.
. You will
or
−
To continuously replay
REPEAT a track, press the RPT button. You will see RPT in the display. Press it again to turn it off.
96
−
RANDOM This feature plays the tracks in random order. To activate Random Play, press and release the RDM button. You will see RDM in the display. Press it again to return to normal play.
) to
To Stop Playing a CD Press the eject button ( remove the CD. If you eject the CD, but do not remove it from the slot, the system will automatically reload the CD after 15 seconds and put it in pause mode. To begin playing, press the CD button. Press the AM/FM button to switch to the radio while a CD is playing. Press the CD button to play the CD.
If you turn the system off while a CD is playing, either with the PWR/VOL knob or by turning off the ignition, the disc will stay in the drive. When you turn the system back on, the CD will begin playing where it left off.
Operating the Optional CD Changer A CD changer is available for your vehicle. It holds up to six CDs. You operate the CD changer with the same controls used for the in-dash CD player.
Load the desired CDs in the magazine, and load the magazine in the changer according to the instructions that came with the unit.
To select the CD changer, press the CD button. The CD and track numbers will be displayed. To select a different CD, use the preset 5
(DISC ) or preset 6 (DISC ) ＋ button. If you select an empty slot in the magazine, the changer will, after finding that slot empty, try to load the CD in the next slot.−
０４／０７／１６ １３：１２：０７ ３１Ｓ５Ｔ６３０ ０１００
General Information
When using CD-R discs, use only high quality CDs labeled for audio use.
When recording a CD-R, the recording must be closed for it to be used by the system.
CD-RW discs will not work in this unit.
Play only standard round CDs. Odd-shaped CDs may jam in the drive or cause other problems.
Handle your CDs properly to prevent damage and skipping.
Do not use discs with adhesive labels. The label can curl up and cause the disc to jam in the unit.
Protecting CDs When a CD is not being played, store it in its case to protect it from dust and other contamination. To prevent warpage, keep CDs out of direct sunlight and extreme heat.
To clean a CD, use a clean soft cloth. Wipe across the CD from the center to the outside edge.
A new CD may be rough on the inner and outer edges. The small plastic pieces causing this roughness can flake off and fall on the re- cording surface of the CD, causing skipping or other problems. Remove these pieces by rubbing the inner and outer edges with the side of a pencil or pen.
Never try to insert foreign objects in the CD player or the magazine.
Protecting Your CDs
Handle a CD by its edges; never touch either surface. Do not place stabilizer rings or labels on the CD. These, along with contamination from fingerprints, liquids, and felt-tip pens, can cause the CD to not play properly, or possibly jam in the drive.
97
０４／０７／１６ １３：１２：１５ ３１Ｓ５Ｔ６３０ ０１０１
CD Player Error Messages
If you see an error message in the display while playing a CD, find the cause in the chart to the right. If you cannot clear the error message, take your vehicle to your dealer.
Error
Message
Cause
Solution
FOCUS Error
Mechanical Error
High temperature
Press the EJECT button and pull out the CD. Check if it is inserted correctly in the CD player. Make sure the CD is not scratched or damaged. Press the EJECT button and pull out the CD. Check the CD for damage or deformation. If the CD cannot be pulled out, or the error message does not disappear after the CD is ejected, see your dealer. Will disappear when the temperature returns to normal.
98
０４／０７／１６ １３：１２：２４ ３１Ｓ５Ｔ６３０ ０１０２
If you see an error message in the display while playing a CD, find the cause in the chart to the right. If you cannot clear the error message, take your vehicle to your dealer.
Error
Message
CD Changer Error Messages
Cause
Solution
FOCUS Error
No CD in the CD magazine
Mechanical Error
High temperature
No CD magazine in the CD changer
Press the magazine eject button and pull it out. Check for an error message, and insert the magazine again. If the message does not disappear or the magazine cannot be pulled out, see your dealer. Insert CD.
Press the magazine eject button and pull it out. Check for an error message, and insert the magazine again. If the message does not disappear or the magazine cannot be pulled out, see your dealer. Will disappear when the temperature returns to normal. Insert CD magazine.
99
０４／０７／１６ １３：１２：２９ ３１Ｓ５Ｔ６３０ ０１０３
Playing a Tape
TAPE BUTTON
REWIND BUTTON
FAST FORWARD BUTTON
REPEAT INDICATOR
DOLBY INDICATOR
POWER/VOLUME KNOB
SKIP BAR
PLAY/PROGRAM BUTTON
NR BUTTON
REPEAT BUTTON
100
０４／０７／１６ １３：１２：４１ ３１Ｓ５Ｔ６３０ ０１０４
To Play a Tape Optionalonallmodels The ignition switch must be in the ACCESSORY (I) or ON (II) position. Make sure the open side of the tape is facing right, then insert the tape most of the way into the slot. The system will pull the tape in the rest of the way, and begin to play it.
▲
indicates the
The tape direction indicator comes on to show you which side of the tape is playing. The side you inserted upward is now playing. If you want to play the other side, press the PLAY/PROG button. When the player reaches the end of the tape, it will automatically reverse direction and play the other side.
＊
Dolby noise reduction turns on when you insert a tape. The
indicator comes on. If the tape was not recorded in Dolby, turn it off by pressing the NR button. Dolby remains off until you press the NR button again.
＊
Dolby noise reduction is manufactured under
license from Dolby Laboratories Licensing Corporation. ‘‘DOLBY’’ and the double-D symbol
are trademarks of Dolby Laboratories
Licensing Corporation.
To Stop Playing a Tape To remove the tape, press the tape EJECT button. If you want to turn the player off, press the PWR/VOL knob or turn off the ignition. The tape will remain in the drive. When you turn the system back on, the tape will begin playing where it left off.
Playing a Tape
To switch to the radio or CD player while a tape is playing, press the AM/FM or CD/TAPE button. To change back to the tape player, press the CD/TAPE button.
−
To rewind the tape,
Tape Search Functions FF/REW push the REW button. You will see REW in the display. To fast forward the tape, push the FF button. You will see FF displayed. Press the FF, REW, or PLAY/PROG button to take the system out of rewind or fast forward.
−
Press
button to find
SKIP the beginning of the current song or passage. Press button to find the beginning of the next song or passage. When the system reaches the beginning of a song or passage, it begins to play it.
101
０４／０７／１６ １３：１２：５１ ３１Ｓ５Ｔ６３０ ０１０５
Caring for the Tape and Player The tape player picks up dirt and oxides from the tape. This contamination builds up over time and causes the sound quality to degrade. To prevent this, you should clean the player after every 30 hours of use.
If you do not clean the tape player regularly, it may eventually become impossible to remove the contamination with a normal cleaning kit. Your dealer has a cleaning kit available.
Use 100-minute or shorter tapes. Tapes longer than that may break or jam the drive.
If the tape is loose, tighten it by turning the hub with a pencil or your finger. If the label is peeling off, remove it or it could cause the tape to jam in the player. Never try to insert a warped or damaged tape in the player.
Store tapes in their cases to protect them from dust and moisture. Never place tapes where they will be exposed to direct sunlight, high heat, or high humidity. If a tape is exposed to extreme heat or cold, let it reach a moderate temperature before inserting it into the player.
Never insert foreign objects into the cassette player.
Playing a Tape
− Press the RPT button
REPEAT to continuously play a song or passage. You will see RPT displayed. The track will repeat until you press the RPT button again.
The SKIP and REPEAT
NOTE: functions use silent periods on the tape to find the end of a song or passage. These features may not work if there is almost no gap between selections, a high noise level, or a silent period in the middle of a selection.
102
０４／０７／１６ １３：１３：００ ３１Ｓ５Ｔ６３０ ０１０６
Your vehicle’s audio system will disable itself if it is disconnected from electrical power for any reason. To make it work again, you must enter a specific five-digit code in the preset buttons. Because there are hundreds of number combinations possible from five-digits, making the system work without knowing the exact code is nearly impossible.
You should have received a card that lists your audio system code number and serial number. It is best to store this card in a safe place at home. In addition, you should write the audio system’s serial number in this Owner’s Manual.
If you lose the card, you must obtain the code number from a dealer. To do this, you will need the system’s serial number.
If your vehicle’s battery is discon- nected or goes dead, the audio system will disable itself. If this happens, you will see ‘‘COdE’’ in the frequency display the next time you turn on the system. Use the preset buttons to enter the five-digit code. The code is on the radio code card included in your Owner’s Manual kit. When it is entered correctly, the radio will start playing.
If you make a mistake entering the code, do not start over; complete the five-digit sequence, then enter the correct code. You have ten tries to enter the correct code. If you are unsuccessful in ten attempts, you must then leave the system on for 1
hour before trying again.Radio Theft Protection
If the code card is lost, your dealer can access your code with your radio’s serial number. To access the serial number, turn the radio on. It must display ‘‘COdE’’, then turn the radio off. Push the preset 1, preset 6, and power buttons at the same time, then quickly release.
You will have to store your favorite stations in the preset buttons after the system begins working. Your original settings were lost when the power was disconnected.
103
０４／０７／１６ １３：１３：０８ ３１Ｓ５Ｔ６３０ ０１０７
Setting the Clock
CLOCK (SCAN/RPT) BUTTON
hour.
For example: 1:06 will reset to 1:00
1:52 will reset to 2:00HOUR BUTTON MINUTE BUTTON
RESET BUTTON
If your vehicle’s battery is disconnected or goes dead, you will need to set the clock.
Press and hold the CLOCK button until you hear a beep. Change the hours by pressing the H (Preset 4) button until the numbers advance to the desired time. Change the minutes by pressing the M (Preset 5) button until the numbers advance to the desired time. When you are
finished, press the CLOCK button again.
You can quickly set the time to the nearest hour. If the displayed time is before the half hour, press and hold the CLOCK button until you hear a beep, then press the R (Preset 6) button to set the clock back to the previous hour. If the displayed time is after the half hour, the clock sets forward to the beginning of the next
104
０４／０７／１６ １３：１３：１８ ３１Ｓ５Ｔ６３０ ０１０８
Cruise control allows you to maintain a set speed above 25 mph (40 km/h) without keeping your foot on the accelerator pedal. It should be used for cruising on straight, open highways. It is not recommended for city driving, winding roads, slippery roads, heavy rain, or bad weather.
Improper use of the cruise control can lead to a crash.
Use the cruise control only when traveling on open highways in good weather.
Cruise Control
UsingtheCruiseControl
CANCEL BUTTON
CRUISE CONTROL MASTER SWITCH
1.
Push in the Cruise Control Master Switch. The indicator in the switch will come on.
2.
Accelerate to the desired cruising speed above 25 mph (40 km/h).
RESUME/ accel BUTTON
SET/decel BUTTON
3.
Press and release the SET/decel button on the steering wheel. The indicator on the instrument panel comes on to show the system is now activated.
CONTINUED
105
０４／０７／１６ １３：１３：２９ ３１Ｓ５Ｔ６３０ ０１０９
Cruise Control
Cruise control may not hold the set speed when you are going up and down hills. If your speed increases going down a hill, use the brakes to slow down. This will cancel the cruise control. To resume the set speed, press the RESUME/accel button. The indicator on the instrument panel will come back on.
106
ChangingtheSetSpeed You can increase the set cruising speed in any of these ways:
Press and hold the RESUME/ accel button. When you reach the desired cruising speed, release the button.
To increase the speed in very small amounts, tap the RESUME/ accel button. Each time you do this, your vehicle speeds up about 1 mph (1.6 km/h).
Push on the accelerator pedal. Accelerate to the desired cruising speed, and press the SET/decel button.
You can decrease the set cruising speed in any of these ways:
Press and hold the SET/decel button. Release the button when you reach the desired speed.
To slow down in very small amounts, tap the SET/decel button. Each time you do this, your vehicle slows down about 1
mph (1.6 km/h).Tap the brake or clutch pedal lightly with your foot. The CRUISE CONTROL indicator on the instrument panel goes out. When the vehicle slows to the desired speed, press the SET/ decel button.
０４／０７／１６ １３：１３：３９ ３１Ｓ５Ｔ６３０ ０１１０
Even with the cruise control turned on, you can still use the accelerator pedal to speed up for passing. After completing the pass, take your foot off the accelerator pedal. The vehicle will return to the set cruising speed.
Resting your foot on the brake or clutch pedal causes the cruise control to cancel.
CancellingtheCruiseControl You can cancel the cruise control in any of these ways:
Tap the brake or clutch pedal.
Push the CANCEL button on the steering wheel.
Push the Cruise Control Master Switch.
Cruise Control
Resuming the Set Speed When you push the CANCEL button, or tap the brake or clutch pedal, the system remembers the previously-set cruising speed. To return to that speed, accelerate to above 25 mph (40 km/h) and then press and release the RESUME/ accel button. The CRUISE CONTROL indicator comes on. The vehicle will accelerate to the same cruising speed as before.
Pressing the Cruise Control Master Switch turns the system completely off and erases the previous cruising speed.
107
０４／０７／１６ １３：１３：４６ ３１Ｓ５Ｔ６３０ ０１１２
Before Driving
Before you begin driving your vehicle, you should know what gasoline to use, and how to check the levels of important fluids. You also need to know how to properly store luggage or packages. The information in this section will help you. If you plan to add any accessories to your vehicle, please read the information in this section first.
Break-in Period Fuel Recommendations Service Station Procedures
............................. ............... ......... .......................................
Fueling Opening and Closing the
. 110
. 110
. 111
. 111Hood
Oil Check Engine Coolant Check
. 112
. 113
. 114
Fuel Economy . 114
Accessories and Modifications . 115
Carrying Cargo . 117....................................... ................................... ............. ............................... ... .............................
109
０４／０７／１６ １３：１３：５８ ３１Ｓ５Ｔ６３０ ０１１３
Break-in Period, Fuel Recommendation
Break-in Period Help assure your vehicle’s future reliability and performance by paying extra attention to how you drive during the first 600 miles (1,000 km). During this period:
Avoid full-throttle starts and rapid acceleration.
Avoid hard braking for the first 200 miles (300 km).
Do not change the oil until the scheduled maintenance time.
You should follow these same recommendations with an overhauled or exchanged engine, or when the brakes are relined.
Fuel Recommendation Your vehicle is designed to operate on unleaded gasoline with a pump octane number of 86 or higher. Use of a lower octane gasoline can cause a persistent, heavy metallic rapping noise that can lead to engine damage.
We recommend using quality gasoline containing detergent additives that help prevent fuel system and engine deposits.
In addition, in order to maintain good performance, fuel economy, and emissions control, we strongly recommend, in areas where it is available, the use of gasoline that does NOT contain manganese-based fuel additives such as MMT.
Use of gasoline with these additives may adversely affect performance, and cause the Malfunction Indicator Lamp on your instrument panel to come on. If this happens, contact
110
your dealer for service.
For further important fuel-related information, please refer to your Quick Start Guide
Some gasoline today is blended with oxygenates such as ethanol or MTBE. Your vehicle is designed to operate on oxygenated gasoline containing up to 10 percent ethanol by volume and up to 15 percent MTBE by volume. Do not use gasoline containing methanol.
If you notice any undesirable operating symptoms, try another service station or switch to another brand of gasoline.
