You may also be interested in...
Download PDF Manual


TOC


Index


Home


299


2012 Civic Sedan CIVIC 4D-31TR3600.book 300 ページ 2011年2月14日 月曜日 午後2時51分


uuIf a Tire Goes FlatuChanging a Flat Tire


■ Getting Ready to Replace the Flat Tire


1. Open the trunk floor lid.


Tool Case


2. Take the tool case out of the trunk. Take the jack and wheel nut wrench out of the tool case.


3. Unscrew the wing bolt, and remove the spacer cone. Then, remove the spare tire.


1Getting Ready to Replace the Flat Tire


2.4 ℓ engine models NOTICE Do not mount the compact spare on the front. If mounted on the front, the compact spare, smaller in size than the normal tire, may damage the differential.


If either front tire goes flat, remove the rear tire on the same side, and mount the compact spare on the rear and the rear tire on the front.


QRG


TOC


Spare Tire


4. Place a wheel block or rock in front and rear


of the wheel diagonal to the flat tire.


Index


Home


300


The tire to be replaced.


Wheel Blocks


2012 Civic Sedan CIVIC 4D-31TR3600.book 301 ページ 2011年2月14日 月曜日 午後2時51分


uuIf a Tire Goes FlatuChanging a Flat Tire


5. Place the compact spare tire (wheel side up)


under the vehicle body, near the tire that needs to be replaced.


Models with 15 x 6J aluminum wheels 6. Remove the center cap from the wheel with


the jack handle bar.


All models 7. Loosen each wheel nut about one turn


using the wheel nut wrench.


Continued


QRG


TOC


Index


Home


301


2012 Civic Sedan CIVIC 4D-31TR3600.book 302 ページ 2011年2月14日 月曜日 午後2時51分


uuIf a Tire Goes FlatuChanging a Flat Tire


■ How to Set Up the Jack


1. Place the jack under the jacking point


closest to the tire to be changed.


QRG


TOC


Index


Home


302


Jack Handle Bar


Wheel Nut Wrench as Jack Handle


1How to Set Up the Jack


3WARNING


The vehicle can easily roll off the jack, seriously injuring anyone underneath.


Follow the directions for changing a tire exactly, and never get under the vehicle when it is supported only by the jack.


Do not use the jack with people or luggage in the vehicle.


Use the jack provided in your vehicle. Other jacks may not support the weight ("load") or their shape may not match.


The following instructions must be followed to use the jack safely. • Do not use while the engine is running. • Use only where the ground is firm and level. • Use only at the jacking points. • Do not get in the vehicle while using the jack. • Do not put anything on top of or underneath the


jack.


2. Turn the end bracket (as shown in the


image) clockwise until the top of the jack contacts the jacking point. u Make sure that the jacking point tab is


resting in the jack notch.


3. Raise the vehicle, using the jack handle bar and the jack handle, until the tire is off the ground.


2012 Civic Sedan CIVIC 4D-31TR3600.book 303 ページ 2011年2月14日 月曜日 午後2時51分


uuIf a Tire Goes FlatuChanging a Flat Tire


■ Replacing the Flat Tire


Models with aluminum wheels 1. Remove the wheel nuts and flat tire.


1Replacing the Flat Tire


Do not over tighten the wheel nuts by applying extra torque using your foot or a pipe.


Wheel Cover


Models with wheel cover 1. Remove the wheel nuts, wheel cover, and


flat tire.


Models with wheel cover Do not attempt to forcibly pry the wheel cover off with a screwdriver or other tool. The wheel cover cannot be removed without first removing the wheel nuts.


QRG


All models 2. Wipe the mounting surfaces of the wheel


with a clean cloth.


3. Mount the compact spare tire.


4. Screw the wheel nuts until they touch the lips around the mounting holes, and stop rotating.


Continued


TOC


Index


Home


303


2012 Civic Sedan CIVIC 4D-31TR3600.book 304 ページ 2011年2月14日 月曜日 午後2時51分


uuIf a Tire Goes FlatuChanging a Flat Tire


QRG


5. Lower the vehicle and remove the jack.


Tighten the wheel nuts in the order indicated in the image. Go around, tightening the nuts, two to three times in this order. Wheel nut torque: 80 lbf∙ft (108 N∙m, 11 kgf∙m)


■ Storing the Flat Tire


Wing Bolt Spacer Cone


For normal tire


For compact spare tire


Models with aluminum wheels 1. Remove the center cap. All models 2. Place the flat tire face down in the spare tire


well.


3. Remove the spacer cone from the wing


bolt, flip it over, and insert it back on the bolt. Secure the flat tire with the wing bolt.


4. Securely put the jack and wheel nut wrench back in the tool case. Store the case in the trunk.


TOC


Index


Home


304


1Storing the Flat Tire


3WARNING


Loose items can fly around the interior in a crash and can seriously injure the occupants. Store the wheel, jack, and tools securely before driving.


2012 Civic Sedan CIVIC 4D-31TR3600.book 305 ページ 2011年2月14日 月曜日 午後2時51分


uuIf a Tire Goes FlatuChanging a Flat Tire


■ TPMS and the Spare Tire U.S. models with information display If you replace a flat tire with the spare tire, the low tire pressure indicator comes on while you are driving. After driving for a few miles (kilometers), the indicator will go off and the TPMS indicator comes on, but this is normal.


If you replace the tire with a specified regular tire, the low tire pressure or TPMS indicator will go off after a few miles (kilometers).


1TPMS and the Spare Tire


The system cannot monitor the pressure of the spare tire. Manually check the spare tire pressure to be sure that it is correct.


Use TPMS specific wheels. Each is equipped with a tire pressure sensor mounted inside the tire behind the valve stem.


U.S. models with multi-information display If you replace a flat tire with the spare tire, the low tire pressure/TPMS indicator comes on while you are driving. After driving for a few miles (kilometers), the indicator will start blinking for a short time and then stay on. "CHECK TPMS SYSTEM" appears on the multi-information display, but this is normal.


If you replace the tire with a specified regular tire, the warning message on the multi-information display and the TPMS indicator will go off after a few miles (kilometers).


QRG


TOC


Index


Home


305


2012 Civic Sedan CIVIC 4D-31TR3600.book 306 ページ 2011年2月14日 月曜日 午後2時51分


Engine Does Not Start


Checking the Engine If the engine does not start, turn the ignition switch to START (e and check the starter.


1Checking the Engine


If you must start the vehicle immediately, use an assisting vehicle to jump start it.


2 Jump Starting P. 307


Starter condition


Starter doesn’t turn or turns over slowly. The battery may be dead. Check each of the items on the right and respond accordingly. The starter turns over normally but the engine doesn’t start. There may be a problem with the fuse. Check each of the items on the right and respond accordingly.


Checklist


Check brightness of the interior light. Turn on interior lights and check brightness. ● If the interior lights are dim or do not come on at all


2 Battery P. 289


● If the interior lights come on normally 2 Fuses P. 318
Review the engine start procedure. Follow its instructions, and try to start the engine again. 2 Starting the Engine P. 211
Check the immobilizer system indicator. When the immobilizer system indicator is blinking, the engine cannot be started.


2 Immobilizer System P. 112


Check the fuel level. There should be enough fuel in the tank. 2 Fuel Gauge P. 78
Check the fuse. Check all fuses, or have the vehicle checked by a dealer.


2 Inspecting and Changing Fuses P. 320


If the problem continues:


2 Emergency Towing P. 321


QRG


TOC


Index


Home


306


2012 Civic Sedan CIVIC 4D-31TR3600.book 307 ページ 2011年2月14日 月曜日 午後2時51分


Jump Starting


■ Jump Starting Procedure Turn off the power to electric devices, such as audio and lights. Turn off the engine, then open the hood. 1.8 ℓ engine models


1. Connect the first jumper cable to your


vehicle's battery + terminal.


2. Connect the other end of the first jumper cable to the assisting vehicle's + terminal. u Use a 12-volt booster battery only.


3. Connect the second jumper cable to the


assisting vehicle's - terminal.


Booster Battery


2.4 ℓ engine models


Booster Battery


1Jump Starting


3WARNING


A battery can explode if you do not follow the correct procedure, seriously injuring anyone nearby.


Keep all sparks, open flames, and smoking materials away from the battery.


Securely attach the jumper cables clips so that they do not come off when the engine vibrates. Also be careful not to tangle the jumper cables or allow the cable ends to touch each other while attaching or detaching the jumper cables.


QRG


TOC


Index


Home


307


Continued


2012 Civic Sedan CIVIC 4D-31TR3600.book 308 ページ 2011年2月14日 月曜日 午後2時51分


4. Connect the other end of the second


1Jump Starting


Battery performance degrades in cold conditions and may prevent the engine from starting.


jumper cable to the engine mounting bolt as shown. Do not connect this jumper cable to any other part.


5. If your vehicle is connected to another


vehicle, start the assisting vehicle's engine and increase its rpm slightly.


6. Attempt to start your vehicle's engine. If it


turns over slowly, check that the jumper cables have good metal-to-metal contact.


uuJump Startingu


QRG


1.8 ℓ engine models


2.4 ℓ engine models


TOC


Index


Home


308


2012 Civic Sedan CIVIC 4D-31TR3600.book 309 ページ 2011年2月14日 月曜日 午後2時51分


■ What to Do After the Engine Starts Once your vehicle's engine has started, remove the jumper cables in the following order.


1. Disconnect the jumper cable from your vehicle's ground.


2. Disconnect the other end of the jumper cable from the assisting vehicle's battery


- terminal.


3. Disconnect the jumper cable from your vehicle's battery + terminal.


4. Disconnect the other end of the jumper cable from the assisting vehicle's battery


+ terminal.


Have your vehicle inspected by a nearby service station or a dealer.


uuJump Startingu


QRG


TOC


Index


Home


309


2012 Civic Sedan QRG


CIVIC 4D-31TR3600.book 310 ページ 2011年2月14日 月曜日 午後2時51分


Shift Lever Does Not Move


Automatic transmission models Follow the procedure below if you cannot move the shift lever out of the (P position.


■ Releasing the Lock


Slot


Cover


1. Set the parking brake.


2. Remove the key from the ignition switch.


3. Wrap a cloth around the tip of a small flat- tip screwdriver and remove the cover of the shift lock release slot. u Put the tip of the flat-tip screwdriver into


the slot and remove it as shown in the image.


4. Insert the key into the shift lock release slot.


5. While pushing on the key, press the shift


lever release button and place the shift lever into (N. u The lock is now released. Have the shift


lever checked by a dealer as soon as possible.


TOC


Release Button


Shift Lock Release Slot


Index


Home


310


2012 Civic Sedan CIVIC 4D-31TR3600.book 311 ページ 2011年2月14日 月曜日 午後2時51分


Overheating


How to Handle Overheating Overheating symptoms are as follows: • The high temperature indicator comes on or the engine suddenly loses power.


• Steam is coming out of the engine compartment.


■ First thing to do 1. Immediately park the vehicle in a safe place.


Automatic transmission models u Move the shift lever to (P and set the parking brake. Turn off all accessories


and turn on the hazard warning lights.


Manual transmission models u Move the shift lever to (N and set the parking brake. Turn off all accessories


and turn on the hazard warning lights.


2. No steam coming out: Keep the engine running and open the hood.


Steam coming out: Turn off the engine and wait until steam goes away. Then, open the hood.


1How to Handle Overheating


3WARNING


Steam and spray from an overheated engine can seriously scald you.


Do not open the hood if steam is coming out.


NOTICE Continuing to drive with the high temperature indicator on may damage the engine.


QRG


TOC


Index


Home


311


Continued


2012 Civic Sedan CIVIC 4D-31TR3600.book 312 ページ 2011年2月14日 月曜日 午後2時51分


uuOverheatinguHow to Handle Overheating


QRG


■ Next thing to do


MAX


MIN


Reserve Tank


1. Check that the cooling fan is operating and stop the engine once the high temperature indicator goes off. u If the cooling fan is not operating,


immediately stop the engine.


2. Once the engine has cooled down, inspect


the coolant level and check the cooling system components for leaks. u If the coolant level in the reserve tank is


low, add coolant until it reaches the MAX mark.


u If there is no coolant in the reserve tank, check that the radiator is cool. Cover the radiator cap with a heavy cloth and open the cap. If necessary, add coolant up to the base of the filler neck, and put the cap back on.


1How to Handle Overheating


3WARNING


Removing the radiator cap while the engine is hot can cause the coolant to spray out, seriously scalding you.


Always let the engine and radiator cool down before removing the radiator cap.


If the coolant is leaking, contact a dealer for repairs.


Use water as an emergency/temporary measure only. Have a dealer flush the system with proper antifreeze as soon as possible.


■ Last thing to do Once the engine has cooled sufficiently, restart it and check the high temperature indicator.


If the high temperature indicator is off, resume driving. If it stays on, contact a dealer for repairs.


TOC


Index


Home


312


2012 Civic Sedan CIVIC 4D-31TR3600.book 313 ページ 2011年2月14日 月曜日 午後2時51分


Indicator, Coming On/Blinking


If the Low Oil Pressure Indicator Comes On


■ Reasons for the indicator to come on Comes on when the engine oil pressure is low. ■ What to do as soon as the indicator comes on 1. Immediately park the vehicle in a safe place.


2. If necessary, turn the hazard warning lights on. ■ What to do after parking the vehicle 1. Stop the engine and let it sit for about one minute.


2. Open the hood and check the oil level.


u Add oil as necessary.


3. Start the engine and check the low oil pressure indicator.


u The light goes out: Start driving again. u The light does not go out within 10 seconds: Stop the engine and


contact a dealer for repairs immediately.


If the Charging System Indicator Comes On


■ Reasons for the indicator to come on Comes on when the battery is not being charged. ■ What to do when the indicator comes on Turn off the heating and cooling * system, rear defogger, and other electrical systems, and immediately contact a dealer for repairs.


* Not available on all models


1If the Low Oil Pressure Indicator Comes On


NOTICE Running the engine with low oil pressure can cause serious mechanical damage almost immediately.


QRG


1If the Charging System Indicator Comes On


If you need to stop temporarily, do not turn off the engine. Restarting the engine may rapidly discharge the battery.


TOC


Index


Home


313


2012 Civic Sedan CIVIC 4D-31TR3600.book 314 ページ 2011年2月14日 月曜日 午後2時51分


uuIndicator, Coming On/BlinkinguIf the Malfunction Indicator Lamp Comes On or Blinks


If the Malfunction Indicator Lamp Comes On or Blinks


■ Reasons for indicator lamp to come on or blink • Comes on when there is a problem with the engine emissions control


system, or the fuel fill cap is missing, or loose.


• Blinks when engine misfiring is detected. ■ What to do when the indicator lamp comes on Avoid high speeds and immediately get your vehicle inspected at a dealer. ■ What to do when the indicator lamp blinks Park the vehicle in a safe place with no flammable items and wait at least ten minutes or more with the engine stopped until it cools.


1If the Malfunction Indicator Lamp Comes On or Blinks


NOTICE If you drive with the malfunction indicator lamp on, the emissions control system and the engine could be damaged.


If the malfunction indicator lamp blinks again when restarting the engine, drive to the nearest dealer at 31 mph (50 km/h) or less. Have your vehicle inspected.


■ Check/Tighten Fuel Cap Message ■ The message appears on when: An evaporative system leak is detected. This may be caused by the fuel fill cap being loose or not being installed.


QRG


TOC


■ What to do when the message appears: 1. Stop the engine. 2. Check that the fuel fill cap is fully installed.


u If not, loosen the cap, and then retighten it until it clicks at least once.


3. Drive for several days of normal driving.


u The message should go off.


■ When the malfunction indicator lamp comes on Malfunction indicator lamp comes on if the system continues to detect a leak of gasoline vapor. If this happens, check the fuel fill cap using the procedures described above.


Index


Home


314


2012 Civic Sedan CIVIC 4D-31TR3600.book 315 ページ 2011年2月14日 月曜日 午後2時51分


uuIndicator, Coming On/BlinkinguIf the Brake System Indicator Comes On


If the Brake System Indicator Comes On


U.S.


■ Reasons for the indicator to come on • The brake fluid is low.


Canada


• There is a malfunction in the brake system. ■ What to do when the indicator comes on while driving Press the brake pedal lightly to check pedal pressure.


• If normal, check the brake fluid level the next time you stop.


• If abnormal, take immediate action. If necessary, downshift the


transmission to slow the vehicle using engine braking.


1If the Brake System Indicator Comes On


Have your vehicle repaired immediately.


It is dangerous to drive with low brake fluid. If there is no resistance from the brake pedal, stop immediately in a safe place. If necessary downshift the gears.


If the brake system indicator and ABS indicator come on simultaneously, the electronic brake distribution system is not working. This can result in vehicle instability under sudden braking. Have your vehicle inspected by a dealer immediately.


If the EPS Indicator Comes On


■ Reasons for the indicator to come on • Comes on when there is a problem with EPS.


• If you depress the accelerator pedal repeatedly to increase the engine


speed while the engine is idling, the indicator comes on, and sometimes the steering wheel becomes harder to operate.


■ What to do when the indicator comes on Stop the vehicle in a safe place and restart the engine. If the indicator comes on and stays on, immediately have your vehicle inspected by a dealer.


1If the EPS Indicator Comes On


NOTICE If you repeatedly turn the steering wheel at an extremely low speed, or hold the steering wheel on the full left or right position for a while, the system heats up. The system goes into a protective mode, and limits its performance. The steering wheel becomes harder and harder to operate. Once the system cools down, EPS is restored. Repeated operation under these conditions can eventually damage the system.


QRG


TOC


Index


Home


315


2012 Civic Sedan CIVIC 4D-31TR3600.book 316 ページ 2011年2月14日 月曜日 午後2時51分


1If the Low Tire Pressure Indicator Comes On


NOTICE Driving on an extremely underinflated tire can cause it to overheat. An overheated tire can fail. Always inflate your tires to the prescribed level.


uuIndicator, Coming On/BlinkinguIf the Low Tire Pressure Indicator Comes On


U.S. models with information display If the Low Tire Pressure Indicator Comes On


■ Reasons for the indicator to come on A tire pressure is significantly low. If the compact spare tire is installed, the indicator stays on for a while, and then goes off. ■ What to do when the indicator comes on Stop your vehicle in a safe place. Check the tire pressure and adjust the pressure to the specified level. The specified tire pressure is on a label on the driver side doorjamb.


U.S. models with information display If the TPMS Indicator Comes On


■ Reasons for the indicator to come on • Comes on when there is a problem with the TPMS.


• If the compact spare is installed, the indicator comes on after driving


for a few miles (kilometers).


■ What to do when the indicator comes on Have the tire inspected by a dealer as soon as possible. If the compact spare tire has triggered the indicator to comes on, change the tire to a full size tire. The indicator goes off after a while.


QRG


TOC


Index


Home


316


2012 Civic Sedan CIVIC 4D-31TR3600.book 317 ページ 2011年2月14日 月曜日 午後2時51分


uuIndicator, Coming On/BlinkinguIf the Low Tire Pressure/TPMS Indicator Comes On or Blinks


U.S. models with multi-information display If the Low Tire Pressure/TPMS Indicator Comes On or Blinks


■ Reasons for the indicator to come on or blink A tire pressure is significantly low. If there is a problem with the TPMS or the compact spare tire is installed, the indicator blinks for about one minute, and then stays on. ■ What to do when the indicator comes on Stop your vehicle in a safe place. Check the tire pressure and adjust the pressure to the specified level. The specified tire pressure is on a label on the driver side doorjamb. ■ What to do when the indicator blinks Have the tire inspected by a dealer as soon as possible. If the compact spare tire has triggered the indicator to blink, change the tire to a full size tire. The indicator goes off after a while.


1If the Low Tire Pressure/TPMS Indicator Comes On or Blinks


NOTICE Driving on an extremely underinflated tire can cause it to overheat. An overheated tire can fail. Always inflate your tires to the prescribed level.


QRG


TOC


Index


Home


317


2012 Civic Sedan CIVIC 4D-31TR3600.book 318 ページ 2011年2月14日 月曜日 午後2時51分


Fuses


Fuse Locations If any electrical devices are not working, turn the ignition switch to LOCK (0 and check to see if any applicable fuse is blown.


Fuse locations are shown on the fuse box cover. Locate the fuse in question by the fuse number and box cover number.


■ Engine Compartment Fuse Box Located near the brake fluid reservoir. Push the tabs to open the box.


QRG


TOC


Index


Home


318


* Not available on all models


10


■ Circuit protected and fuse rating


Circuit Protected


Circuit Protected


EPS −


ABS/VSA Motor ABS/VSA FSR



Main Fuse IG Main


Fuse Box Main Fuse Box Main 2
Headlight Main



Rear Defogger



Blower



Sub Fan Motor Main Fan Motor



Amps 70 A



30 A 30 A



100 A 50 A 60 A 60 A 30 A



30 A



40 A



20 A 20 A



Oil Level


Fog Lights *


Hazard FI Sub IG Coil Stop Horn


11
12
13 Driver’s Power Seat Sliding * 14
15
16
17
18
19
20
21
22
23


INJ IGP DBW H/L LO


Premium Amp *


24


25
26
27
28
29


Driver’s Power Seat


Reclining * MG Clutch



SMALL


Interior Lights


Backup


Amps 7.5 A (20 A) (20 A) 10 A 15 A 15 A 15 A 10 A (20 A) (15 A) 15 A 15 A 20 A


(20 A)


7.5 A



20 A 7.5 A 10 A


Left Headlight Low Beam


10 A 7.5 A Right Headlight Low Beam 10 A


Starter DIAG, ST MG


− − − −


− − − −


2012 Civic Sedan CIVIC 4D-31TR3600.book 319 ページ 2011年2月14日 月曜日 午後2時51分


uuFusesuFuse Locations


Circuit Protected


Amps 15 A 7.5 A 7.5 A


− −


Small Lights Illumination


33 Door Lock Motor 1 (Lock) 34
35
36
37
38
10 A 39 Right Headlight High Beam 10 A 40
(7.5 A) 20 A 41
42
20 A


Left Headlight High Beam


Door Lock


TPMS *


Driver’s Power Window Rear Passenger’s Side


− −


43


44


45


46


Power Window


Front Passenger’s Side


Power Window


Rear Driver’s Side Power


Window Wiper


(20 A)


20 A


(20 A)


30 A


■ Interior Fuse Box Located under the dashboard.


Fuse Label


Fuse locations are shown on the label on the side panel. Locate the fuse in question by the fuse number and label number.


■ Circuit protected and fuse rating


Circuit Protected



ACG SRS


Fuel Pump


8 Door Lock Motor 2 (Unlock) 9 Door Lock Motor 1 (Unlock)


Power Window


VB SOL *


Meter


Amps



15 A 10 A 15 A 7.5 A 7.5 A (15 A) 15 A 15 A


* Not available on all models


10
11


12


13
14


15


16
17
18
19
20
21
22
23
24
25
26


27


28
29


30


Circuit Protected



Moonroof *


Accessory Power Socket


(Center Console) *



Seat Heaters *


Driver’s Door Lock Motor


(Unlock) *


− − −


ACC


ACC Key Lock


Daytime Running Lights


HAC



ABS/VSA


− −


Accessory Power Socket


(Front) Washer


ODS


Driver’s Door Lock Motor


(Lock) *


31
32 Door Lock Motor 2 (Lock)



Amps



(20 A)


(15 A)



(15 A)


(10 A)


− − −


7.5 A 7.5 A 7.5 A 7.5 A



7.5 A


− −


15 A


15 A 7.5 A


(10 A)



15 A


QRG


TOC


Index


Home


319


2012 Civic Sedan CIVIC 4D-31TR3600.book 320 ページ 2011年2月14日 月曜日 午後2時51分


uuFusesuInspecting and Changing Fuses


QRG


Inspecting and Changing Fuses


1. Turn the ignition switch to LOCK (0. Turn


1Inspecting and Changing Fuses


Blown Fuse


headlights and all accessories off.


2. Remove the fuse box cover.


3. Check the large fuse in the engine


compartment. u If the fuse is blown, use a Phillips-head


screwdriver to remove the screw and replace it with a new one.


4. Inspect the small fuses in the engine compartment and the vehicle interior. u If there is a burned out fuse, remove it


with the fuse puller and replace it with a new one.


NOTICE Replacing a fuse with one that has a higher rating greatly increases the chances of damaging the electrical system.


Replace fuse with a spare fuse of the same specified amperage.


Confirm the specified amperage using the charts on P. 318 to 319.


There is a fuse puller on the back of the engine compartment fuse box cover.


Combined Fuse


Fuse Puller


TOC


Index


Home


320


2012 Civic Sedan CIVIC 4D-31TR3600.book 321 ページ 2011年2月14日 月曜日 午後2時51分


Emergency Towing


Call a professional towing service if you need to tow your vehicle.


1Emergency Towing


■ Flat bed equipment The operator loads your vehicle on the back of a truck. This is the best way to transport your vehicle.


■ Wheel lift equipment The tow truck uses two pivoting arms that go under the front tires and lift them off the ground. The rear tires remain on the ground. This is an acceptable way to tow your vehicle.


NOTICE Trying to lift or tow your vehicle by the bumpers will cause serious damage. The bumpers are not designed to support the vehicle's weight.


NOTICE Improper towing such as towing behind a motorhome or other motor vehicle can damage the transmission.


Never tow your vehicle with just a rope or chain. It is very dangerous, since ropes or chains may shift from side to side or break.


QRG


TOC


Index


Home


321


2012 Civic Sedan CIVIC 4D-31TR3600.book 322 ページ 2011年2月14日 月曜日 午後2時51分


Civic


QRG


TOC


Index


Home


322


2012 Sedan CIVIC 4D-31TR3600.book 323 ページ 2011年2月14日 月曜日 午後2時51分


QRG


Index


Home


Information


This chapter includes your vehicle's specifications, locations of identification numbers, and other information required by regulation.


Specifications .................................... 324
Identification Numbers


Vehicle Identification Number (VIN)...... 328
Engine Number and Transmission Number...................................... 328
Devices that Emit Radio Waves ....... 329
Reporting Safety Defects ................. 330


Emissions Testing


Testing of Readiness Codes.............. 331
Warranty Coverages ........................ 333
Authorized Manuals......................... 335
Customer Service Information......... 336


323


2012 Civic Sedan CIVIC 4D-31TR3600.book 324 ページ 2011年2月14日 月曜日 午後2時51分


Specifications


QRG


■ Engine Specifications Displacement


110 cu-in (1,798 cm3) NGK DENSO


DILZKR7B11GS DXU22HCR-D11S


Spark Plugs


■ Fuel Fuel: Type Fuel Tank Capacity ■ Battery


Capacity/Type


Unleaded gasoline, Pump octane number of 87 or higher 13.2 US gal (50 ℓ)


36AH(5)/45AH(20) 36AH(5)/47AH(20) 38AH(5)/47AH(20)


■ Washer Fluid


Tank Capacity


U.S.: 2.6 US qt (2.5 ℓ) Canada: 4.8 US qt (4.5 ℓ)


■ Light Bulbs Headlights (Low Beam) Headlights (High Beam) Front Turn Signal/Parking/Side Marker Lights Brake/Taillights Back-Up Lights Rear Turn Signal Lights Rear Side Marker Lights High-Mount Brake Light Rear License Plate Light Trunk Light Interior Lights


51W (HB4) 60W (HB3)


28/8W


21/5W 21W 21W (Amber) 3CP 21W 5W 5W


Map Lights*3
Ceiling Light


8W 8W


*3: Not available on all models


Honda Civic 4-Door


1.8 ℓ engine models ■ Vehicle Specifications Model No. of Passengers: Front Rear Total Weights: Gross Vehicle Weight Rating


U.S.: 3,660 lbs (1,660 kg)*1
Canada: 1,660 kg*1
U.S.: 3,792 lbs (1,720 kg)*2
Canada: 1,720 kg*2


Gross Axle Weight Rating (Front)


Gross Axle Weight Rating (Rear)


U.S.: 1,985 lbs (900 kg)*1
Canada: 900 kg*1
U.S.: 2,029 lbs (920 kg)*2
Canada: 920 kg*2


U.S.: 1,742 lbs (790 kg)*1
Canada: 790 kg*1
U.S.: 1,786 lbs (810 kg)*2
Canada: 810 kg*2


Air Conditioning: Refrigerant Type Charge Quantity Lubricant Type *1: DX, LX and HF models *2: EX and EX-L models


HFC-134a (R-134a) 13.2 – 15.0 oz (375 – 425 g) SP-10


TOC


Index


Home


324


2012 Civic Sedan CIVIC 4D-31TR3600.book 325 ページ 2011年2月14日 月曜日 午後2時51分


■ Brake/Clutch Fluid Specified ■ Automatic Transmission Fluid


Honda Heavy Duty Brake Fluid DOT 3


Specified


Honda ATF DW-1
(automatic transmission fluid) Change


Capacity ■ Manual Transmission Fluid Specified Capacity


Honda Manual Transmission Fluid Change


1.5 US qt (1.4 ℓ)


2.5 US qt (2.4 ℓ)


■ Engine Oil


Capacity


Recommended


3.7 US qt (3.5 ℓ)


·Genuine Honda Motor Oil 0W-20
·API Premium-grade 0W-20 detergent oil Change Change including filter ■ Engine Coolant Specified Ratio


Honda Long-Life Antifreeze/Coolant Type2
50/50 with distilled water 1.48 US gal (5.59 ℓ) (change including the remaining 0.125 US gal (0.475 ℓ) in the reserve tank)


3.9 US qt (3.7 ℓ)


Capacity


uuSpecificationsu


QRG


■ Tire


Regular


Compact Spare


Size


Pressure psi(kPa[kgf/cm2]) Size Pressure psi(kPa[kgf/cm2])


Wheel Size


Regular


Compact Spare


*1: DX and LX models *2: HF model *3: EX and EX-L models


P195/65R15 89H*1
P195/65R15 89S*2
P205/55R16 89H*3
30 (210 [2.1])*1
32 (220 [2.2])*2, *3
T135/80D15 99M


60 (420 [4.2])


15 x 6J*1, *2
16 x 6 1/2J*3
15 x 4T


TOC


Index


Home


Continued


325


2012 Civic Sedan CIVIC 4D-31TR3600.book 326 ページ 2011年2月14日 月曜日 午後2時51分


uuSpecificationsu


QRG


■ Engine Specifications Displacement


144 cu-in (2,354 cm3) NGK DENSO


ILZKR7B-11S SXU22HCR11S


Spark Plugs


■ Fuel Fuel: Type Fuel Tank Capacity ■ Battery Capacity/Type ■ Washer Fluid


Unleaded gasoline, Pump octane number of 91 or higher 13.2 US gal (50 ℓ)


38AH(5)/47AH(20)


Tank Capacity


U.S.: 2.6 US qt (2.5 ℓ)

Loading...
x