replays all the tracks/files in the selected folder in the order they are stored. To activate folder repeat, press and hold the RPT button (preset 1) until you see FOLDER REPEAT in the display.
ToSelectRepeat,RandomorScan Mode: You can select any type of repeat, random and scan modes with the RPT, RDM and SCAN buttons. To confirm the selected mode, press the AUDIO button to show the audio control display on the navigation screen.
−
TRACK REPEAT This feature continuously plays a track/file. To activate track repeat, press and release the RPT button (preset 1). You will see TRACK REPEAT in the display.
200
2010 Civic Hybrid09/07/15 10:56:16 31SNC640_206
Playing a USB Flash Memory Device (Models with navigation system)
−
TRACK RANDOM This feature plays all the tracks/files in random order. To activate track random, press and release the RDM button (preset 2). You will see TRACK RANDOM in the display.
−
This
FOLDER RANDOM feature plays the tracks/files in the selected folder in random order. To activate folder random, press and hold the RDM button (preset 2) until you see FOLDER RANDOM in the display.
Press and hold the button until you hear a beep to turn off either random mode.
−
This feature
TRACK SCAN samples all tracks/files in the selected folder in the order they are stored. To activate track scan, press and release the SCAN button. You will see TRACK SCAN in the display. You will get a 10 second sampling of each track/file in the folder.
−
FOLDER-SCAN This feature samples the first track/file in each folder in the order they are stored. To activate folder scan, press and hold the SCAN button until you see FOLDER SCAN in the display. You will get a 10 second sampling of each first track/file in the folder(s).
Press and hold the button until you hear a beep to turn off either scan mode. Pressing either SKIP button also turns off this feature.
201
2010 Civic Hybrid09/07/15 10:56:24 31SNC640_207
Playing a USB Flash Memory Device (Models with navigation system)
USB Flash Memory Device Error Messages If you see an error message in the screen, see page
203
DisconnectingaUSBFlashMemory Device You can disconnect the USB flash memory device at any time even if the USB mode is selected on the audio system. Make sure to follow the USB flash memory device’s instructions when you remove it.
When you disconnect the USB flash memory device while it is playing, the audio display (if selected) shows NO DATA.
If you reconnect the same USB flash memory device, the system will begin playing where it left off.
*
To Stop Playing a USB Flash Memory Device To play the radio, press the AM/FM button or touch the FM1, FM2, AM, XM1 , or XM2 icon. Press the CD icon to switch to the disc mode (if a disc is loaded). Each time you press the CD/XM button, the audio mode switches between the USB, disc and XM Radio .
*
*
*
U.S. models only
If a PC card is in the audio unit, touch the CARD icon to play the PC card.
202
2010 Civic Hybrid09/07/15 10:56:28 31SNC640_208
USB Flash Memory Device Error Messages (Models with navigation system)
If you see an error message on the screen while playing a USB flash memory device, find the solution in the chart to the right. If you cannot clear the error message, take your vehicle to your dealer.
Error Message
UNPLAYABLE FILE
UNSUPPORTED
NO SONG
Solution
The system cannot read the file(s). Check the files in the USB flash memory device. There is a possibility that the files have been damaged. Appears when the unsupported USB flash memory device is connected. There is no music information.
203
2010 Civic Hybrid09/07/15 10:56:37 31SNC640_209
AM/FM Radio Reception
Radio Frequencies The radio can receive the complete AM and FM bands. Those bands cover these frequen- cies:
AM band: 530 to 1,710 kHz FM band: 87.7 to 107.9 MHz
Radio stations on the AM band are assigned frequencies at least 10 kHz apart (530, 540, 550). Stations on the FM band are assigned frequencies at least 0.2 MHz apart (87.9, 88.1, 88.3).
Stations must use these exact frequencies. It is fairly common for stations to round-off the frequency in their advertising, so your radio could display a frequency of 100.9 even though the announcer may identify the station as ‘‘FM101.’’
204
Radio Reception How well the radio receives stations is dependent on many factors, such as the distance from the station’s transmitter, nearby large objects, and atmospheric conditions.
A radio station’s signal gets weaker as you get farther away from its transmitter. If you are listening to an AM station, you will notice the sound volume becoming weaker, and the station drifting in and out. If you are listening to an FM station, you will see the stereo indicator flickering off and on as the signal weakens. Eventually, the stereo indicator will go off and the sound will fade completely as you get out of range of the station’s signal.
Driving very near the transmitter of a station that is broadcasting on a frequency close to the frequency of the station you are listening to can also affect your radio’s reception. You may temporarily hear both stations, or hear only the station you are close to.
2010 Civic Hybrid09/07/15 10:56:43 31SNC640_210
Radio signals, especially on the FM band, are deflected by large objects such as buildings and hills. Your radio then receives both the direct signal from the station’s transmitter, and the deflected signal. This causes the sound to distort or flutter. This is a main cause of poor radio reception in city driving.
Radio reception can be affected by atmospheric conditions such as thunderstorms, high humidity, and even sunspots. You may be able to receive a distant radio station one day and not receive it the next day because of a change in conditions.
AM/FM Radio Reception
Electrical interference from passing vehicles and stationary sources can cause temporary reception problems.
AsrequiredbytheFCC: Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser’s authoritytooperatetheequipment.
205
2010 Civic Hybrid09/07/15 10:56:52 31SNC640_211
Protecting Your Discs
General Information
When using CD-R or CD-RW discs, use only high quality discs labeled for audio use.
When recording a CD-R or CD-RW, the recording must be closed for it to be used by the system.
Play only standard round discs. Odd-shaped discs may jam in the drive or cause other problems.
Handle your discs properly to prevent damage and skipping.
Do not use discs with adhesive labels. The label can curl up and cause the disc to jam in the unit.
206
Protecting Discs When a disc is not being played, store it in its case to protect it from dust and other contamination. To prevent warpage, keep discs out of direct sunlight and extreme heat.
To clean a disc, use a clean soft cloth. Wipe across the disc from the center to the outside edge.
A new disc may be rough on the inner and outer edges. The small plastic pieces causing this roughness can flake off and fall on the recording surface of the disc, causing skipping or other problems. Remove these pieces by rubbing the inner and outer edges with the side of a pencil or pen.
Never try to insert foreign objects in the disc player.
Handle a disc by its edges; never touch either surface. Do not place stabilizer rings or labels on the disc. These, along with contamination from finger prints, liquids, and felt- tip pens, can cause the disc to not play properly, or possibly jam in the drive.
2010 Civic Hybrid09/07/15 10:57:03 31SNC640_212
Additional Information on Recommended Discs The in-dash disc player/changer has a sophisticated and delicate mechanism. If you insert a damaged disc as indicated in this section, it may become stuck inside and damage the audio unit.
Examples of these discs are shown to the right:
Protecting Your Discs
1.
Bubbled, wrinkled, labeled, and excessively thick discs
Bubbled/ Wrinkled
With Label/ Sticker
Using Printer Label Kit
Sealed
With Plastic Ring
2.
Damaged discs
3.
Poor quality discs
Chipped/ Cracked
Warped
Burrs
CONTINUED
207
2010 Civic Hybrid09/07/15 10:57:14 31SNC640_213
Protecting Your Discs
4.
Small, irregular shaped discs
5.
Discs with scratches, dirty discs
Recommended discs are printed with the following logo.
3-inch (8-cm) CD
Triangle Shape
Audio unit may not play the following formats.
Fingerprints, scratches, etc.
CD-R or CD-RW may not play due to the recording conditions.
Scratches and fingerprints on the discs may cause the sound to skip.
Can Shape
Arrow Shape
208
2010 Civic Hybrid09/07/15 10:57:20 31SNC640_214
Your vehicle’s audio system will disable itself if it is disconnected from electrical power for any reason. To make it work again, you must enter a specific five-digit code (or a four-digit code for models with a navigation system) in the preset buttons. Because there are hundreds of number combinations possible from five or four-digits, making the system work without knowing the exact code is nearly impossible.
You should have received a card that lists your audio system’s code and serial numbers. It is best to store this card in a safe place at home. In addition, you should write the audio system’s serial number in this owner’s manual.
If you lose the card, you must obtain the code number from a dealer. To do this, you will need the system’s serial number.
If your vehicle’s battery is disconnected or goes dead, the audio system will disable itself. Use the preset buttons to enter the five-digit code (or a four-digit code for models with a navigation system). The code is on the radio code card included in your owner’s manual kit. When it is entered correctly, the radio will start playing.
Radio Theft Protection
If you make a mistake entering the code, do not start over; complete the five-digit (or a four-digit code for models with a navigation system) sequence, then enter the correct code. You have 10 tries to enter the correct code. If you are unsuccessful in 10 attempts, you must then leave the system on for 1 hour before trying again.
209
2010 Civic Hybrid09/07/15 10:57:27 31SNC640_215
Remote Audio Controls
CH BUTTON
VOL BUTTON
MODE BUTTON
Three controls for the audio system are mounted in the steering wheel hub. These let you control basic functions without removing your hand from the wheel.
210
▲
) or down (
The VOL button adjusts the volume up ( ). Press the top or bottom of the button, hold it until the desired volume is reached, then release it.
▼
The MODE button changes the mode. Pressing the button repeatedly selects FM1, FM2, AM, disc (if a disc is loaded), or a PC card (if it is loaded). On models with XM Radio, you can also select XM1 and XM2.
If an iPod or a USB flash memory device is plugged into the system, you can also select AUX.
+
) of the button, the system
If you are listening to the radio, use the CH button to change stations. Each time you press and release the top ( goes to the next preset station on the band you are listening to. Press and release the bottom ( ) to go back to the previous station.
−
+
To activate the seek function, press and hold the top ( ) or bottom ( − of the CH button until you hear a beep. The system searches up or down from the current frequency to find a station with a strong signal.
If you are playing a disc, the system skips to the beginning of the next track (file in MP3 or WMA format) each time you press the top ( ) of + the CH button. Press the bottom ) to return to the beginning of the − current track or file. Press it twice to return to the previous track or file.
You will see the track/file number and the elapsed time. If the disc has text data or is compressed in MP3 or WMA, you can also see any other information (track title, file name, folder name, etc.).
2010 Civic Hybrid09/07/15 10:57:35 31SNC640_216
+
) of the CH button to
If you are playing a PC card, press the top ( advance to the next file. Press the bottom ( previous file.
) to go back to the
−
In MP3 or WMA mode, you can use the seek function to select folders. Press and hold the top ( ) of the CH button until you hear a beep to skip forward to the first file of the next folder. Press the bottom ( ) to − skip backward to the previous folder.
+
If you are playing a USB flash memory device or iPod with the USB adapter cable (if equipped), press and release the top ( ) of the CH button to skip forward to the beginning of the next file. Press the bottom ( ) to skip backward to the beginning of the current file. Press it twice to return to the previous file.
+
−
Remote Audio Controls, Auxiliary Input Jack
When playing a USB flash memory device, you can also use the seek function to skip the folder. To activate this, press and hold either side of the CH button until you hear a beep.
Auxiliary Input Jack
AUXILIARY INPUT JACK
The auxiliary input jack is underneath the accessory power socket on the front panel. The system will accept auxiliary input from standard audio accessories using a 1/8 inch (3.5 mm) stereo miniplug.
When a compatible audio unit is connected to the jack, press the AUX button (AUX icon on models with navigation system) to select it.
211
2010 Civic Hybrid09/07/15 10:57:43 31SNC640_217
Setting the Clock
Onmodelswithoutnavigationsystem To set the time, press the CLOCK button until the displayed time begins to blink, then release the button.
Change the hours by pressing the H (preset 1) button until the numbers advance to the desired time. Change the minutes by pressing the M (preset 2) button until the numbers advance to the desired time.
Press the CLOCK button again to enter the set time.
You can quickly set the time to the nearest hour. If the displayed time is before the half hour, pressing the CLOCK button until you hear a beep, then pressing the R (preset 3) button sets the clock back to the previous hour. If the displayed time is after the half hour, the clock sets forward to the beginning of the next hour.
212
CLOCK BUTTON
HOUR BUTTON
RESET BUTTON
MINUTE BUTTON
For example:
1:06 will reset to 1:00
1:52 will reset to 2:00
Onmodelswithnavigationsystem The navigation system receives signals from the global positioning system (GPS), and the displayed time is updated automatically by the GPS. Refer to the navigation system manual for how to adjust the time.
2010 Civic Hybrid09/07/15 10:57:49 31SNC640_218
The security system helps to protect
your vehicle and valuables from theft.
The horn sounds and a combination
of headlights (low beam), parking
lights, side marker lights, and
taillights flash if someone attempts
to break into your vehicle or remove
the radio. This alarm continues for 2
minutes, then it stops. To reset an
activated system before the 2
minutes have elapsed, unlock the
driver’s door with the key or the
remote transmitter.
The security system automatically sets 15 seconds after you lock the doors, hood, and trunk. For the system to activate, you must lock the doors from the outside with the key, driver’s lock tab, door lock master switch, or remote transmitter. The security system indicator on the instrument panel starts blinking immediately to show you the system is setting itself.
Security System
sound if the trunk lock is forced, or the trunk is opened with the trunk release handle.
The security system will not set if the hood, trunk, or either door is not fully closed. If the system will not set, turn the ignition switch to the ON (II) position, and check the indicators on the instrument panel. Close either door or the trunk indicated on the display. Check the hood visually since it is not part of the display, and shut it if necessary.
To see if the system is set
NOTE: after you exit the vehicle, press the LOCK button on the remote transmitter within 5 seconds. If the system is set, the horn will beep once. Do not attempt to alter this system or add other devices to it.
213
SECURITY SYSTEM INDICATOR
Once the security system is set, opening any door, the trunk, or the hood without using the key or the remote transmitter will cause the alarm to be activated. It will also be activated if the audio unit is removed from the dashboard or the wiring is cut.
With the system set, you can still open the trunk with the master key or the remote transmitter without triggering the alarm. The alarm will
2010 Civic Hybrid09/07/15 10:57:57 31SNC640_219
Cruise Control
Cruise control allows you to maintain a set speed above 25 mph (40 km/h) without keeping your foot on the accelerator pedal. It should be used for cruising on straight, open highways. It is not recommended for city driving, winding roads, slippery roads, heavy rain, or bad weather.
Improper use of the cruise control can lead to a crash.
Use the cruise control only when traveling on open highways in good weather.
Using the Cruise Control
CRUISE BUTTON
RES/ACCEL BUTTON
CANCEL BUTTON
SET/DECEL BUTTON
1.
Push the CRUISE button on the steering wheel. The CRUISE MAIN indicator on the instrument panel comes on.
2.
Accelerate to the desired cruising speed above 25 mph (40 km/h).
3.
Press and release the SET/ DECEL button on the steering wheel. The CRUISE CONTROL indicator on the instrument panel comes on to show the system is now activated.
Cruise control may not hold the set speed when you are going up and down hills. If your speed increases going down a hill, use the brakes to slow down. This will cancel cruise control. To resume the set speed, press the RES/ACCEL button. The indicator on the instrument panel will come back on.
214
2010 Civic Hybrid09/07/15 10:58:05 31SNC640_220
Changing the Set Speed You can increase the set cruising speed in any of these ways:
Press and hold the RES/ACCEL button. When you reach the desired cruising speed, release the button.
To increase your speed in very small amounts, tap the RES/ ACCEL button. Each time you do this, the vehicle will speed up about 1 mph (1.6 km/h).
Push on the accelerator pedal. Accelerate to the desired cruising speed, then press the SET/ DECEL button.
You can decrease the set cruising speed in any of these ways:
Press and hold the SET/DECEL button. Release the button when you reach the desired speed.
To slow down in very small amounts, tap the SET/DECEL button. Each time you do this, your vehicle will slow down about 1 mph (1.6 km/h).
Tap the brake pedal lightly with your foot. The CRUISE CONTROL indicator on the instrument panel will go out. When the vehicle slows to the desired speed, press the SET/ DECEL button.
Cruise Control
Even with the cruise control turned on, you can still use the accelerator pedal to speed up for passing. After completing the pass, take your foot off the accelerator pedal. The vehicle will return to the set cruising speed.
Resting your foot on the brake pedal causes cruise control to cancel.
215
2010 Civic Hybrid09/07/15 10:58:12 31SNC640_221
Cruise Control
Canceling Cruise Control
CRUISE BUTTON
CANCEL BUTTON
You can cancel cruise control in any of these ways:
Tap the brake pedal.
Push the CANCEL button on the steering wheel.
Push the CRUISE button on the steering wheel.
216
Resuming the Set Speed When you push the CANCEL button, or tap the brake or clutch pedal, the system will remember the previously set cruising speed. To return to that speed, accelerate to above 25 mph (40 km/h), and then press and release the RES/ACCEL button. The CRUISE CONTROL indicator comes on. The vehicle will accelerate to the same cruising speed as before.
Pressing the CRUISE button turns the system off and erases the previous cruising speed.
2010 Civic Hybrid09/07/15 10:58:22 31SNC640_222
Onmodelswithnavigationsystem HandsFreeLink (HFL) Bluetooth allows you to place and receive phone calls using voice commands, without handling your cell phone.
To use HFL, you need a Bluetooth- compatible cell phone. For a list of compatible phones, pairing procedures, and special feature capabilities:
Using HFL HFLButtons
HFL TALK BUTTON
NAVI VOICE CONTROL BUTTONS
In the U.S., visit com
or call (888) 528-7876.
handsfreelink.honda.
In Canada, visit (888) 9-HONDA-9.
www.honda.ca,
or call
HFL BACK BUTTON
HFL Talk button release to give a command or answer a call.
Press and
−
−
HFL Back button release to end a call, go back to the previous command, or cancel the command.
Press and
Bluetooth HandsFreeLink
VoiceControlTips
MICROPHONE
Air or wind noise from the dashboard and side vents and all windows may interfere with the microphone. Adjust or close them as necessary.
CONTINUED
217
2010 Civic HybridMany commands can be spoken together. For example, you can say ‘‘Call 123-456- ’’ or ‘‘Dial Peter.’’
####
When HFL is in use, navigation voice commands cannot be recognized.
To change the volume level of HFL, use the audio system volume knob or the steering wheel volume controls.
HelpFeatures
To hear general HFL information, including help on pairing a phone or setting up the system, say ‘‘Tutorial.’’
For help at any time, including a list of available commands, say ‘‘Hands free help.’’
09/07/15 10:58:29 31SNC640_223
Bluetooth HandsFreeLink
Press and release the HFL Talk button each time you want to make a command. After the beep, speak in a clear, natural tone.
Try to reduce all background noise. If the microphone picks up voices other than yours, commands may be misinterpreted.
218
2010 Civic Hybrid09/07/15 10:58:36 31SNC640_224
Information Display
Bluetooth HandsFreeLink
BLUETOOTH INDICATOR
A notification that there is an incoming call, or HFL is in use, will appear on the navigation screen when the audio system is on.
HFL MESSAGE
On the map screen, you will see a ‘‘HFL’’ message on the screen.
indicator will also be
displayed on the screen if your phone is linked to HFL.
219
2010 Civic Hybrid09/07/15 10:58:44 31SNC640_225
Bluetooth HandsFreeLink
How to Use HFL
The ignition switch must be in the ACCESSORY (I) or ON (II) position.
‘‘Pair’’
‘‘Edit’’
Pair a phone to the system (See page 223)
Edit the name of a paired phone (See page 224)
‘‘Phone Setup’’
‘‘Delete’’
Delete a paired phone from the system (See page 224)
Press HFL Talk button
‘‘List’’
‘‘Status’’
‘‘Next Phone’’
Hear a list of all phones paired to the system (See page 224) Hear which paired phone is currently linked to the system (See page 225) Search for another previously paired phone to link to (See page 225)
‘‘Set Pairing Code’’
Set the pairing code to a ‘‘Fixed’’ or ‘‘Random’’ number (See page 225)
‘‘Call’’ or ‘‘Dial’’
‘‘123-555-
####
’’
Enter desired phone number (See page 226)
‘‘Jim Smith’’
Once a phonebook entry is stored, you can say a name here. (See page 226)
Press and release the HFL Talk button each time you give a command.
220
2010 Civic Hybrid09/07/15 10:58:50 31SNC640_226
Bluetooth HandsFreeLink
‘‘Redial’’
‘‘Transfer’’
‘‘Mute’’
‘‘Send’’
Redial the last number called (See page 227)
Transfer a call from HFL to your phone, or from your phone to HFL (See page 229)
Mute your voice to the person at the other end of the call (See page 230)
Send numbers or names during a call (See page 230)
Press HFL Talk button
‘‘Store’’
‘‘Edit’’
Store a phonebook entry (See page 231)
Edit the name of an existing phonebook entry (See page 231)
‘‘Phonebook’’
‘‘Delete’’
Delete a phonebook entry (See page 232)
‘‘Receive Contact’’
‘‘List’’
If your phone supports this function, use this to transfer contacts from your phone to HFL (See page 232)
Hear a list of all stored phonebook entries (See page 232)
Press and release the HFL Talk button each time you give a command.
CONTINUED
221
2010 Civic Hybrid09/07/15 10:58:56 31SNC640_227
Bluetooth HandsFreeLink
‘‘System Set up’’
Press HFL Talk button
‘‘Security’’
Apply a security passcode to the system that must be input at each key cycle to access the system (See page 237)
‘‘Change Passcode’’
Change your security passcode (See page 238)
‘‘Call Notification’’
‘‘Auto Transfer’’
Set how you would like to be notified of an incoming call (See page 238)
Set calls to automatically transfer from your phone to HFL when you enter the vehicle (See page 238)
‘‘Clear’’
Clear the system of all paired phones, phonebook entries and security passcode (See page 239)
‘‘Change Language’’
Change language from English to French (See page 239) *
‘‘Tutorial’’
Hear a tutorial for general rules on using the system (See page 218)
‘‘Hands Free Help’’
Hear a list of available commands and additional information describing each command (See page 218)
Press and release the HFL Talk button each time you give a command. : Canadian models
*
222
2010 Civic Hybrid09/07/15 10:59:07 31SNC640_228
Bluetooth HandsFreeLink
To use HFL, you need to pair your Bluetooth-compatible cell phone to the system.
Phone Setup This command group is available for paired cell phones.
Phonepairingtips
You cannot pair your phone while the vehicle is moving.
Your phone must be in discovery or search mode to pair. Refer to your phone’s manual.
Up to six phones can be paired.
Your phone’s battery may drain faster when it is paired to HFL.
If after three minutes your phone is not ready to pair or a phone is not found, the system will time out and return to idle.
Topairacellphone: 1.
Press and release the HFL Talk button. If you are pairing a phone for the first time, HFL will give you information about the pairing process. If it is not the first phone you are pairing, say ‘‘ setup Pair
Phone .’’
’’ and say ‘‘
2.
Follow the HFL prompts and put your phone in discovery or search mode. HFL will give you a 4-digit pairing code and begin searching for your phone.
3.
When your phone finds a Bluetooth device, select HFL from the options and enter the 4-digit code from the previous step.
4.
Follow the HFL prompts and name the newly paired phone.
CONTINUED
223
2010 Civic Hybrid09/07/15 10:59:18 31SNC640_229
Bluetooth HandsFreeLink
Torenameapairedphone: Press and release the HFL Talk button before a command.
Todeleteapairedphone: Press and release the HFL Talk button before a command.
1.
Say ‘‘
Phone setup
.’’
1.
Say ‘‘
Phone setup
.’’
Say ‘‘
Delete
’’ after the prompts.
HFL will ask you which phone you want to delete. Follow the HFL prompts to continue with the deletion.
2.
Say ‘‘
Edit
’’ after the prompts.
3.
If there is more than one phone paired to the system, HFL will ask you which phone’s name you want to change. Follow the HFL prompts and rename the phone.
2.
3.
224
Tohearthenamesofallpaired phones: Press and release the HFL Talk button before a command.
1.
Say ‘‘
Phone setup
.’’
2.
Say ‘‘
List
’’ after the prompts.
3.
HFL will read out all the paired phone’s names.
2010 Civic Hybrid09/07/15 10:59:30 31SNC640_230
Tohearwhichpairedphoneis currentlylinked: Press and release the HFL Talk button before a command.
Tochangefromthecurrentlylinked phonetoanotherpairedphone: Press and release the HFL Talk button before a command.
1.
2.
3.
Say ‘‘
Phone setup
.’’
Say ‘‘
Status
’’ after the prompts.
HFL will tell you which phone is linked to the system.
1.
2.
3.
4.
Say ‘‘
Phone setup
.’’
Next phone
’’ after the
Say ‘‘ prompts.
HFL disconnects the linked phone and searches for another paired phone.
Once another phone is found, it is linked to the system. HFL will inform you which phone is now linked.
Bluetooth HandsFreeLink
Tochangethepairingcodesetting: Press and release the HFL Talk button before a command.
1.
2.
3.
Say ‘‘
Phone setup
.’’
Set pairing code
’’ after the
Say ‘‘ prompts.
If you want HFL to create a random code each time you pair a phone, say ‘‘ .’’ If you want to choose your own 4-digit code to be used each time, say ‘‘ and follow the HFL prompts.
Random
Fixed ’’
If no other phones are found or paired, HFL will inform you that the original phone is linked again.
225
2010 Civic Hybrid09/07/15 10:59:42 31SNC640_231
Bluetooth HandsFreeLink
Making a Call You can make calls using any phone number or a name in the HFL phonebook. You can also redial the last number called.
Bluetooth is the wireless technology
that links your phone to HFL. HFL
uses a Class 2 Bluetooth, which
means the maximum range between
your phone and vehicle is 30 feet (10
meters).
During a call, HFL allows you to talk up to 30 minutes after you remove the key from the ignition switch. However, this may weaken the vehicle’s battery.
226
Tomakeacallusingaphone number: Press and release the HFL Talk button before a command.
Tomakeacallusinganameinthe HFLphonebook: Press and release the HFL Talk button before a command.
1.
Say ‘‘
Call
’’ or ‘‘
Dial
.’’
1.
Say ‘‘
Call
’’ or ‘‘
Dial
.’’
2.
Follow the HFL prompts and say the phone number you want to dial.
3.
Follow the HFL prompts to confirm the number and say Call ‘‘
’’ or ‘‘
Dial
.’’
Once connected, you will hear the person you called through the audio speakers.
2.
3.
Follow the HFL prompts and say the name stored in the HFL phonebook that you want to call.
Follow the HFL prompts to confirm the name and make the call.
2010 Civic Hybrid09/07/15 10:59:50 31SNC640_232
Toredialthelastnumbercalledby HFL: Press and release the HFL Talk button and say ‘‘
Redial
.’’
Bluetooth HandsFreeLink
Tomakeacallfromanimported phonebook:
1.
Press the INFO button, then select Cellular Phonebook ‘‘
.’’
3.
Select a phonebook you want to choose a phone number from.
2.
Select ‘‘ Phonebook
.’’
Search Imported
If the phonebook you select is PIN- protected, you will need to enter the PIN to access it. See page more information.
235
for
CONTINUED
227
2010 Civic Hybrid09/07/15 10:59:59 31SNC640_233
Bluetooth HandsFreeLink
List ICON
To search for a specific name in the phonebook, enter the keyword for either the first or last name.
4.
Select the name. All the phone numbers stored for that name will be listed.
To display all names in the List phonebook, select the ‘‘
’’ option.
5.
Select the desired number to call from the list.
228
Store in
Selecting ‘‘ HandsFreeLink number will be stored in HFL, so that you can call it using HFL’s name tag by voice.
,’’ the phone
2010 Civic Hybrid09/07/15 11:00:06 31SNC640_234
Receiving a Call When you receive a call, an incoming call notification (if activated) will play and interrupt the audio system if it is on.
CallWaiting If your phone has Call Waiting, press and release the HFL Talk button to put the original call on hold and answer the incoming call.
Press the HFL Talk button to answer the call, or the HFL Back button to hang up.
To return to the original call, press the HFL Talk button again. If you don’t want to answer the incoming call, disregard it and continue with your original call. If you want to hang up the original call and answer the new call, press the HFL Back button.
Bluetooth HandsFreeLink
Transferring a Call You can transfer a call from HFL to your phone, or from your phone to HFL.
Press and release the HFL Talk button and say ‘‘
Transfer
.’’
229
2010 Civic Hybrid09/07/15 11:00:17 31SNC640_235
Bluetooth HandsFreeLink
Muting a Call You can mute your voice to the person you are talking to during a call.
To mute your voice during a call, press and release the HFL Talk button and say ‘‘
Mute
.’’
To unmute your voice, press and release the HFL Talk button and say Mute ‘‘
’’ again.
230
Send Numbers or Names During a Call HFL allows you to send numbers or names during a call. This is useful when you call a menu-driven phone system.
Tosendanameornumberduringa call: Press and release the HFL Talk button before a command.
Phonebook You can store up to 50 names with their associated numbers in HFL. The numbers you store cannot only be phone numbers but other types, such as account numbers or passwords, which can be sent during a menu-driven call.
1.
2.
Say ‘‘
Send
.’’
Follow the HFL prompts and say the name or number you want to send.
3.
Follow the HFL prompts to send the tones and continue the call.
To send a pound (
NOTE: ‘‘pound.’’ To send a star (*), say ‘‘star.’’
), say
#
2010 Civic Hybrid09/07/15 11:00:32 31SNC640_236
Tostoreaphonebookentry: Press and release the HFL Talk button before a command.
NOTE:
Avoid using duplicate name entries.
Toeditthenumberstoredinaname: Press and release the HFL Talk button before a command.
Bluetooth HandsFreeLink
1.
Say ‘‘
Phonebook
.’’
2.
3.
Say ‘‘
Store
’’ after the prompts.
Say a name you want to list as your phonebook entry.
4.
Say the number you want to store for the name entry.
5.
Follow the HFL prompts and say Enter ‘‘
’’ to store the entry.
Avoid using ‘‘home’’ as a name entry.
It is easier for HFL to recognize a multisyllabic or longer name. For example, use ‘‘Peter’’ instead of ‘‘Pete,’’ or ‘‘John Smith’’ instead of ‘‘John.’’
1.
Say ‘‘
Phonebook
.’’
2.
Say ‘‘
Edit
’’ after the prompts.
3.
Follow the HFL prompts and say the name entry you want to edit.
4.
When asked, say the new number for that name.
5.
Follow the HFL prompts to complete the edit.
CONTINUED
231
2010 Civic Hybrid09/07/15 11:00:45 31SNC640_237
Bluetooth HandsFreeLink
Todeleteaname: Press and release the HFL Talk button before a command.
Tolistallnamesinthephonebook: Press and release the HFL Talk button before a command.
1.
Say ‘‘
Phonebook
.’’
1.
Say ‘‘
Phonebook
.’’
2.
3.
Say ‘‘
Delete
’’ after the prompts.
Say the name you want to delete and follow the HFL prompts to complete the deletion.
2.
Say ‘‘
List
’’ after the prompts.
3.
HFL begins reading the names in the order they were stored.
4.
If you hear a name you want to call, immediately press the HFL Talk button and say ‘‘
Call
.’’
Tostoreaspecificphonenumber fromyourcellphonedirectlytothe HFLphonebook(availableonsome phones): Press and release the HFL Talk button before a command.
1.
Say ‘‘
Phonebook
.’’
2.
3.
4.
Receive contact
Say ‘‘ prompts.
’’ after the
Follow the HFL prompts, select a number from your cell phone, and send it to HFL.
Follow the HFL prompts and name the number, or say Discard ‘‘ you want to store.
’’ if it is not the number
5.
Follow the HFL prompts if you want to store another number.
232
2010 Civic Hybrid09/07/15 11:00:57 31SNC640_238
Cellular Phonebook (availableonsomephones) Cellular Phonebook If you select from the Information screen menu, you will see four HFL options.
For a list of cell phones that are compatible with this feature:
In the U.S., visit com
or call (888) 528-7876.
handsfreelink.honda.
In Canada, visit (888) 9-HONDA-9.
www.honda.ca,
or call
Bluetooth HandsFreeLink
ImportCellularPhonebook: The entire phonebook data of the cell phone that is linked to HFL can be imported to the navigation system.
SearchImportedPhonebook: Once a phonebook has been imported, you can search the phone numbers by the person’s name.
IMPORTED PHONEBOOK
PIN ICON
IMPORTED DATE
Import Cellular
Select ‘‘ Phonebook ,’’ and HFL will begin importing the phonebook. Select OK ‘‘
’’ after the import is completed.
Search Imported
Select ‘‘ Phonebook phonebooks will be displayed.
,’’ and a list of imported
Select a phonebook from the list.
CONTINUED
233
2010 Civic Hybrid09/07/15 11:01:09 31SNC640_239
Bluetooth HandsFreeLink
Select a person from the list. Up to three category icons are displayed in the left side of the list:
Fax
Car
Voice
Other
Preference
Home
Mobile
Work
Pager
These indicate how many numbers are stored for the name. If a name has more than three category icons, ‘‘…’’ is displayed.
Select the person’s number you want to call, and press the HFL Talk button.
If the phonebook is PIN-protected, you will need to enter the 4-digit PIN.
List ICON
To search for a specific name in the phonebook, enter the keyword for either the first or last name.
To display all names in the List phonebook, select the ‘‘
’’ option.
234
2010 Civic Hybrid09/07/15 11:01:20 31SNC640_240
DeleteImportedPhonebook: You can delete any imported phonebook.
After making a selection, the following screen will appear.
PIN Number You can add, change, or remove a PIN number from any phonebook.
Bluetooth HandsFreeLink
Delete Imported
Select ‘‘ Phonebook phonebooks will be displayed.
,’’ and a list of imported
Select a phonebook you want to delete. If the phonebook is PIN- protected, you will need to enter the 4-digit PIN number.
Yes Select ‘‘ the deletion.
,’’ then ‘‘
OK
’’ to complete
ToaddaPIN: If you have selected a phonebook without a PIN, you will see the above display.
Enter the new 4-digit PIN. You will have to re-enter the PIN for confirmation.
CONTINUED
235
2010 Civic HybridPIN number
ToremoveaPIN: Select ‘‘ Do not use PIN ‘‘ the current PIN.
,’’ then select ’’ after you enter
09/07/15 11:01:27 31SNC640_241
Bluetooth HandsFreeLink
TochangethePINtoanewnumber:
Select the phonebook you want. The display will change as shown above.
The display will change as shown above.
Enter the current PIN for this phonebook.
Enter the new 4-digit PIN number. You will be asked to re-enter the PIN for verification.
236
2010 Civic Hybrid09/07/15 11:01:37 31SNC640_242
System Setup This command group allows you to change or customize HFL basic settings.
Toseta4-digitpasscodetolockthe HFLsystemforsecuritypurposes: Press and release the HFL Talk button before a command.
1.
Say ‘‘
System setup
.’’
2.
Say ‘‘
Security
’’after the prompts.
3.
Follow the HFL prompts and say the 4-digit passcode you want to set.
4.
Follow the HFL prompts to confirm the number.
Bluetooth HandsFreeLink
Once a passcode is set, you
NOTE:
will need to enter it to use HFL each
time you start the vehicle. If you
forget the code, your dealer will have
to reset it for you, or you will have to
clear the entire system (see page
239
).
CONTINUED
237
2010 Civic Hybrid09/07/15 11:01:50 31SNC640_243
Bluetooth HandsFreeLink
Tochangeyoursecuritypasscode: Press and release the HFL Talk button before a command.
1.
2.
Say ‘‘
System setup
.’’
Change passcode
’’ after the
Say ‘‘ prompts.
3.
Follow the HFL prompts and say the new 4-digit passcode.
4.
Follow the HFL prompts to confirm the number.
238
Toselecteitheraringtoneora promptastheincomingcall notification : Press and release the HFL Talk button before a command.
*
1.
2.
3.
Say ‘‘
System setup