2006 Honda Civic Hybrid Owners Manual

CONTINUED

197

Main MenuTable of Contentsst０５／０９／０９　１８：２２：５４　３１ＳＮＣ６００　０２０１　

Lights

4.

5.

Push the electrical connector back onto the new socket. Make sure it is on all the way.

Insert the socket into the hole, and turn it one-quarter turn clockwise to lock it in place.

6.

Turn on the headlights to test the new socket.

7.

If you replaced a headlight bulb on the driver’s side, reinstall the engine coolant reserve tank.

LowBeamHeadlight

HOLDING CLIP

1.

To change the bulb on the driver’s side, start the engine, turn the steering wheel all the way to the right, and turn off the engine. To change the bulb on the passenger’s side, turn the steering wheel to the left.

2.

Use a flat-tipped screwdriver to remove the two holding clips from the inner fender, and pull the inner fender cover back.

SOCKET CONNECTOR

TAB

2.

3.

Remove the socket from the headlight assembly by turning it one-quarter turn counterclockwise.

Remove the electrical connector from the socket by pushing on the tab and pulling the connector down.

198

Main MenuTable of Contentsst０５／０９／０９　１８：２３：０３　３１ＳＮＣ６００　０２０２　

5.

6.

Insert the new socket into the hole, and turn it one-quarter turn clockwise to lock it in place.

Push the electrical connector back onto the new socket. Make sure it is on all the way.

7.

Turn on the headlights to test the new socket.

8.

Reinstall the inner fender cover. Then reinstall the holding clips, and lock them in place by pushing on their centers.

SOCKET

TAB

3.

4.

Remove the socket from the headlight assembly by turning it one-quarter turn counterclockwise.

Remove the electrical connector from the socket by pushing on the tab and pulling the connector down.

Lights

Replacing the Front Side Marker/ Parking/Turn Signal Light Bulb

HOLDING CLIP

1.

To change the bulb on the driver’s side, start the engine, turn the steering wheel all the way to the right, and turn off the engine. To change the bulb on the passenger’s side, turn the steering wheel to the left.

CONTINUED

199

Main MenuTable of Contentsst０５／０９／１０　１４：３１：４２　３１ＳＮＣ６００　０２０３　

Lights

4.

Remove the bulb from the socket by pushing the bulb in and turning it counterclockwise until it unlocks.

5.

Install the new bulb in the socket. Turn it clockwise to lock it in place.

6.

Insert the socket back into the headlight assembly. Turn it clockwise to lock it in place.

7.

Test the lights to make sure the new bulb is working.

8.

Reinstall the inner fender cover. Then reinstall the holding clips, and lock them in place by pushing on their centers.

Replacing Rear Bulbs (In Fenders)

FASTENER

FASTENER

1.

Open the trunk.

Remove the screw from the center of each fastener on the side of the trunk lining. Pull the lining back.

2.

Determine which of the four bulbs is burned out: stop/taillight, back- up light, turn signal, or side marker.

2.

Use a flat-tipped screwdriver to remove the two holding clips from the inner fender, and pull the inner fender cover back.

3.

Remove the socket from the headlight assembly by turning it one-quarter turn counterclockwise.

200

Main MenuTable of Contentsst０５／０９／１０　１４：３１：５５　３１ＳＮＣ６００　０２０４　

Lights

Replacing Rear Bulbs (in Trunk Lid)

BULBS

BULB

SOCKETS

SOCKETS

BULB

3.

Remove the socket by turning it one-quarter turn counterclockwise.

6.

Test the lights to make sure the new bulb is working.

4.

5.

Pull the bulb straight out of its socket. Push the new bulb straight into the socket until it bottoms.

Reinstall the socket into the light assembly by turning it clockwise until it locks.

7.

8.

Reinstall the trunk lining. Make sure it is installed under the edge of the trunk seal.

Put the fasteners into the holes on the side of the trunk lining. Reinstall the screws.

FASTENERS

1.

Open the trunk.

2.

Remove the screw from the center of each fastener on the trunk lid trim. Pull the trim back.

CONTINUED

201

Main MenuTable of Contentsst０５／０９／１０　１４：３２：０５　３１ＳＮＣ６００　０２０５　

Lights, Roof Antenna

BULB

Roof Antenna

4.

5.

Pull the bulb straight out of its socket. Push the new bulb straight into the socket until it bottoms.

Insert the socket back into the light assembly. Turn it clockwise to lock it in place.

6.

Test the lights to make sure the new bulb is working.

7.

Push the trunk lid trim back into position.

SOCKET Remove the socket by turning it 3. one-quarter turn counterclockwise.

8.

Put the fasteners into the holes on the trunk lid trim. Reinstall the screws.

Before using an automatic car wash, remove the radio antenna so it does not get damaged. Remove the antenna by unscrewing it. When you reinstall the antenna, tighten it securely.

Before entering or parking in areas with low ceiling height, remove the antenna.

202

Main MenuTable of Contentsst０５／０９／０９　１８：２３：４２　３１ＳＮＣ６００　０２０６　

Cleaning the Seat Belts, Floor Mats

Seat Belts

LOOP

Dirt build-up in the loops of the seat belt anchors can cause the belts to retract slowly. Wipe the insides of the loops with a clean cloth dampened in mild soap and warm water or isopropyl alcohol.

Floor Mats

If your seat belts get dirty, use a soft brush with a mixture of mild soap and warm water to clean them. Do not use bleach, dye, or cleaning solvents. Let the belts air dry before you use the vehicle.

Ifequipped The floor mat that came with your vehicle hook over the floor mat anchors. This keeps them from sliding forward and possibly interfering with the pedals.

If you remove the driver’s floor mat, make sure to re-anchor it when you put it back in your vehicle.

CONTINUED

203

Main MenuTable of Contentsst０５／０９／０９　１８：２３：４７　３１ＳＮＣ６００　０２０７　

Floor Mats, Dust and Pollen Filter

If you use non-Honda floor mats, make sure they fit properly and that they can be used with the floor mat anchors. Do not put additional floor mats on top of the anchored mats.

Dust and Pollen Filter This filter removes the dust and pollen that is brought in from the outside through the heating and cooling system.

Have your dealer replace the filter when this service is indicated by a maintenance message on the information display. It should be replaced every 15,000 miles (24,000
km) if you drive primarily in urban areas that have high concentrations of soot in the air, or if the flow from the heating and cooling system becomes less than usual.

Check the condition of the wiper blades at least every 6 months. Replace them if you find signs of cracking in the rubber, and areas that are getting hard or if they leave streaks and unwiped areas when used.

204

Main MenuTable of Contentsst０５／０９／０９　１８：２３：５５　３１ＳＮＣ６００　０２０８　

Wiper Blades

COVER

WIPER ARMS

To replace a wiper blade:

1.

Lift the wiper arm off the windshield, raising the driver’s side first, then the passenger’s side.

Do not open the hood when the wiper arms are raised, or you will damage the hood and wiper arms.

2.

Remove the cover, by squeezing the two tabs and pulling it straight out.

As shown above, cover the tip of a flat-tipped screwdriver with a cloth and move the screwdriver in the direction of the arrow.

CONTINUED

205

Main MenuTable of Contentsst０５／０９／０９　１８：２４：０３　３１ＳＮＣ６００　０２０９　

Wiper Blades

TAB

BLADE ASSEMBLY

REINFORCEMENT STRIP

WIPER BLADE

4.

Remove the blade from the blade assembly:

Find the side of the blade labeled ‘‘LOCK.’’ This is the side you pull out. Pull back the end of the blade assembly on the ‘‘LOCK’’ side of the blade. Then grab the end of the blade, and slide it out.

5.

Examine the new wiper blades. If they have no plastic or metal reinforcement along the back edge, remove the metal reinforcement strips from the old wiper blade, and install them in the slots along the edge of the new blade.

3.

Disconnect the blade assembly from the wiper arm:

Press and hold the lock tab. Slide the blade assembly toward the lock tab until it releases from the wiper arm.

When replacing a wiper blade, make sure not to drop the wiper blade or wiper arm down on the windshield.

206

Main MenuTable of Contentsst０５／０９／１０　１３：３０：１６　３１ＳＮＣ６００　０２１０　

Wiper Blades, Tires

Tires To safely operate your vehicle, your tires must be the proper type and size, in good condition with adequate tread, and correctly inflated.

Inflation Guidelines Keeping the tires properly inflated provides the best combination of handling, tread life, and riding comfort.

The following pages give more detailed information on how to take care of your tires and what to do when they need to be replaced.

Underinflated tires wear unevenly, adversely affect handling and fuel economy, and are more likely to fail from being overheated.

Using tires that are excessively worn or improperly inflated can cause a crash in which you can be seriously hurt or killed.

Follow all instructions in this owner’s manual regarding tire inflation and maintenance.

Overinflated tires can make your vehicle ride more harshly, are more prone to damage from road hazards, and wear unevenly.

We recommend that you visually check your tires every day. If you think a tire might be low, check it immediately with a tire gauge.

6.

Install the new blade onto the blade assembly:

Pull back either end of the blade assembly. Place the side of the blade not labeled ‘‘LOCK’’ on the end of the blade assembly, and slide the blade onto the assembly until it is fully installed.

7.

Slide the wiper blade assembly onto the wiper arm. Make sure it locks in place.

8.

Reinstall the cover onto the blade assembly.

9.

Make sure the blade is completely installed and that its edge is not bunched up.

10.

Lower the wiper arm down against the windshield, the passenger’s side first, then the driver’s side.

207

Main MenuTable of Contentsst０５／０９／０９　１８：２４：２４　３１ＳＮＣ６００　０２１１　

Tires

Use a gauge to measure the air pressure in each tire at least once a month. Even tires that are in good condition may lose 1 to 2 psi (10 to 20 kPa, 0.1 to 0.2 kgf/cm ) per month. Remember to check the spare tire at the same time.

Check the air pressures when the tires are cold. This means the vehicle has been parked for at least 3
hours, or driven less than 1 mile (1.6
km). Add or release air, if needed, to match the recommended cold tire pressures.

208

Recommended Tire Pressures The following chart shows the recommended cold tire pressures for most normal driving conditions and speeds.

Tire Size

P195/65R15 89S

Cold Tire Pressure Front/Rear: 32 psi (220 kPa , 2.2
kgf/cm )

The compact spare tire pressure is: 60 psi (420 kPa , 4.2 kgf/cm )

If you check air pressures when the tires are hot (driven for several miles), you will see readings 4 to 6
psi (30 to 40 kPa, 0.3 to 0.4 kgf/cm ) higher than the cold readings. This is normal. Do not let air out to match the recommended cold air pressure. The tire will be underinflated.

You should get your own tire pressure gauge and use it whenever you check your tire pressures. This will make it easier for you to tell if a pressure loss is due to a tire problem and not due to a variation between gauges.

While tubeless tires have some ability to self-seal if they are punctured, you should look closely for punctures if a tire starts losing pressure.

Main MenuTable of Contentsst０５／０９／０９　１８：２４：３３　３１ＳＮＣ６００　０２１２　

Tire Inspection Every time you check inflation, you should also examine the tires for damage, foreign objects, and wear.

You should look for:

Bumps or bulges in the tread or side of the tire. Replace the tire if you find either of these conditions.

Cuts, splits, or cracks in the side of the tire. Replace the tire if you can see fabric or cord.

Excessive tread wear.

INDICATOR LOCATION MARKS

TREAD WEAR INDICATOR

Your tires have wear indicators molded into the tread. When the tread wears down, you will see a band 1/2 inch (12.7 mm) wide across the tread. This shows there is less than 1/16 inch (1.6 mm) of tread left on the tire.

A tire this worn gives very little traction on wet roads. You should replace the tire if you can see three or more tread wear indicators.

Tires

Tire Maintenance In addition to proper inflation, correct wheel alignment helps to decrease tire wear. If you find a tire is worn unevenly, have your dealer check the wheel alignment.

Have your dealer check the tires if you feel a consistent vibration while driving. A tire should always be rebalanced if it is removed from the wheel. When you have new tires installed, make sure they are balanced. This increases riding comfort and tire life. For best results, have the installer perform a dynamic balance.

Improper wheel weights can damage your wheels. Use only genuine Honda wheel weights f or balancing.

209

Main MenuTable of Contentsst０５／０９／０９　１８：２４：４２　３１ＳＮＣ６００　０２１３　

Tires

Tire Rotation

Front

Front

(Front Non-directional Tires and Wheels)

(Front Directional Tires and Wheels)

To help increase tire life and distribute wear more evenly, rotate the tires according to the maintenance messages displayed on the information display. Move the tires to the positions shown in the chart each time they are rotated. If you purchase directional tires, rotate only front-to-back.

210

speed and may cause the system to activate.

If you ever replace a wheel, make sure the new one matches the specifications of the original. Replacement wheels are available at your dealer.

Installing improper tires on your vehicle can affect handling and stability. This can cause a crash in which you can be seriously hurt or killed.

Always use the size and type of tires recommended in this owner’s manual.

Replacing Tires and Wheels Replace your tires with radial tires of the same size, load range, speed rating, and maximum cold tire pressure rating (as shown on the tire’s sidewall).

Mixing radial and bias-ply tires on your vehicle can reduce braking ability, traction, and steering accuracy. Using tires of a different size or construction can cause the ABS to work inconsistently.

It is best to replace all four tires at the same time. If that is not possible or necessary, replace the two front tires or two rear tires as a pair. Replacing just one tire can seriously affect your vehicle’s handling.

The ABS works by comparing the speed of the wheels. When replacing tires, use the same size originally supplied with the vehicle. Tire size and construction can affect wheel

Main MenuTable of Contentsst０５／０９／０９　１８：２４：５２　３１ＳＮＣ６００　０２１４　

Wheel and Tire Specifications Wheels:

15 x 6 J

Tires:

P195/65R15 89S

244

for DOT tire quality

See page grading information, and page for tire size information. 246

Winter Driving Tires marked ‘‘M S’’ or ‘‘All Season’’ on the sidewall have an all- weather tread design suitable for most winter driving conditions.

＋

For the best performance in snowy or icy conditions, you should install snow tires or tire chains. They may be required by local laws under certain conditions.

Tires

When installing cables, follow the manufacturer’s instructions, and mount them as tight as you can. Make sure they are not contacting the brake lines or suspension. Drive slowly with them installed. If you hear them coming into contact with the body or chassis, stop and investigate. Remove them as soon as you begin driving on cleared roads.

Traction devices that are the wrong size or improperly installed can damage your vehicle’s brake lines, suspension, body, and wheels. Stop driving if they are hitting any part of the vehicle.

SnowTires If you mount snow tires on your vehicle, make sure they are radial tires of the same size and load range as original tires. Mount snow tires on all four wheels. The traction provided by snow tires on dry roads maybelowerthanyouroriginaltires. Check with the tire dealer for maximum speed recommendations.

TireChains Because your vehicle has limited tire clearance, mount only SAE Class ‘‘S’’ cable-type traction devices, with rubber chain tensioners on the front tires. Use traction devices only when required by driving conditions or local laws. Make sure they are the correct size for your tires. Metal link- type ‘‘chains’’ should not be used.

211

Main MenuTable of Contentsst０５／０９／０９　１８：２４：５９　３１ＳＮＣ６００　０２１５　

Checking the 12 Volt Battery

Check the terminals for corrosion (a white or yellowish powder). To remove it, cover the terminals with a solution of baking soda and water. It will bubble up and turn brown. When this stops, wash it off with plain water. Dry off the battery with a cloth or paper towel. Coat the terminals with grease to help prevent further corrosion.

If additional battery maintenance is needed, see your dealer or a qualified technician.

Battery posts,

WARNING: terminals, and related accessories contain lead and lead compounds. Wash your hands after handling.

If you need to connect the battery to a charger, disconnect both cables to prevent damaging your vehicle’s electrical system. Always disconnect the negative ( − reconnect it last.

) cable first, and

The battery gives off explosive hydrogen gas during normal operation.

A spark or flame can cause the battery to explode with enough force to kill or seriously hurt you.

Wear protective clothing and a face shield, or have a skilled mechanic do the battery maintenance.

If your vehicle’s 12 volt battery is disconnected or goes dead, the IMA battery level gauge reading will not be correct the next time you turn the ignition switch to the ON (II) position. It will show less than the actual level temporarily. It will show the correct level after you drive for at least 30 minutes.

TEST INDICATOR WINDOW

Check the condition of the 12 volt battery monthly by looking at the test indicator window. The label on the battery explains the test indicator’s colors.

212

Main MenuTable of Contentsst０５／０９／０９　１８：２５：１０　３１ＳＮＣ６００　０２１６　

Vehicle Storage

If you need to park your vehicle for an extended period (more than 1
month), there are several things you should do to prepare it for storage. Proper preparation helps prevent deterioration and makes it easier to get your vehicle back on the road. If possible, store your vehicle indoors.

Fill the fuel tank.

Block the rear wheels.

If the vehicle is to be stored for a longer period, it should be supported on jackstands so the tires are off the ground.

Leave one window open slightly (if the vehicle is being stored indoors).

Change the engine oil and filter.

Disconnect the 12 volt battery.

Cover the vehicle with a ‘‘breathable’’ cover, one made from a porous material such as cotton. Non-porous materials, such as plastic sheeting, trap moisture, which can damage the paint.

Reconnect the 12 volt battery and drive your vehicle every month for about 30 minutes. This will keep the IMA battery charged and in good condition.

Wash and dry the exterior completely.

Clean the interior. Make sure the carpeting, floor mats, etc., are completely dry.

Leave the parking brake off. Put the transmission in Park.

Support the front wiper blade arms with a folded towel or rag so they do not touch the windshield.

To minimize sticking, apply a silicone spray lubricant to all door and trunk seals. Also, apply a vehicle body wax to the painted surfaces that mate with the door and trunk seals.

If possible, periodically run the engine until it reaches full operating temperature (the cooling fan cycles twice). Preferably, do this once a month.

213

Main MenuTable of Contentsst０５／０９／０９　１８：２５：１６　３１ＳＮＣ６００　０２１８　

Taking Care of the Unexpected

This section covers the more common problems that motorists experience with their vehicles. It gives you information about how to safely evaluate the problem and what to do to correct it. If the problem has stranded you on the side of the road, you may be able to get going again. If not, you will also find instructions on getting your vehicle towed.

Compact Spare Tire Changing a Flat Tire If the Engine Won’t Start Jump Starting If the Engine Overheats Low Oil Pressure Indicator Charging System Indicator Malfunction Indicator Lamp Brake System Indicator Fuses Fuse Locations Emergency Towing

...................... .................... ............. ................................ .............. ......... .......... ....... ............... .............................................. .............................. ......................

. 216
. 217
. 221
. 223
. 225
. 227
. 228
. 229
. 230
. 231
. 235
. 237

215

Main Menust０５／０９／０９　１８：２５：２３　３１ＳＮＣ６００　０２１９　

Compact Spare Tire

Use the compact spare tire as a temporary replacement only. Get your regular tire repaired or replaced, and put it back on your vehicle as soon as you can.

Check the inflation pressure of the compact spare tire every time you check the other tires. It should be inflated to: 60 psi (420 kPa , 4.2 kgf/cm )

216

Follow these precautions:

INDICATOR LOCATION MARK

Never exceed 50 mph (80 km/h).

This tire gives a harsher ride and less traction on some road sur- faces. Use greater caution while driving.

Do not mount snow chains on the compact spare tire.

Do not use your compact spare tire on another vehicle unless it is the same make and model.

TREAD WEAR INDICATOR BAR

Replace the tire when you can see the tread wear indicator bars. The replacement should be the same size and design tire, mounted on the same wheel. The spare tire is not designed to be mounted on a regular wheel, and the spare wheel is not designed for mounting a regular tire.

Main MenuTable of Contentsst０５／０９／１２　１３：５０：４２　３１ＳＮＣ６００　０２２０　

If you have a flat tire while driving, stop in a safe place to change it. Drive slowly along the shoulder until you get to an exit or an area to stop that is far away from the traffic lanes.

The vehicle can easily roll off the jack, seriously injuring anyone underneath.

Follow the directions for changing a tire exactly, and never get under the vehicle when it is supported only by the jack.

1.

2.

Park the vehicle on firm, level, and non-slippery ground. Put the transmission in Park. Apply the parking brake.

Turn on the hazard warning lights, and turn the ignition switch to the LOCK (0) position. Have all passengers get out of the vehicle while you change the tire.

Changing a Flat Tire

JACK

TOOL CASE

TRUNK FLOOR SPARE TIRE Open the trunk. Raise the trunk 3. floor by lifting up on the back edge.

4.

Take the tool case out of the spare tire.

5.

Unscrew the wing bolt, and take the spare tire out of its well.

CONTINUED

217

Main MenuTable of Contentsst０５／０９／１０　１４：３２：１３　３１ＳＮＣ６００　０２２１　

Changing a Flat Tire

JACKING POINTS

6.

Remove the center cap from the wheel with the extension.

7.

Loosen each wheel nut 1/2 turn with the wheel nut wrench.

WHEEL NUT WRENCH

8.

Place the jack under the jacking point. Turn the end bracket clockwise until the top of the jack contacts the jacking point. Make sure the jacking point tab is resting in the jack notch.

218

Main MenuTable of Contentsst０５／０９／１０　１４：３２：２３　３１ＳＮＣ６００　０２２２　

BRAKE HUB

11.

Before mounting the spare tire, wipe any dirt off the mounting surface of the wheel and hub with a clean cloth. Wipe the hub carefully; it may be hot from driving.

WHEEL NUT WRENCH 9.

EXTENSION Use the extension and the wheel nut wrench as shown to raise the vehicle until the flat tire is off the ground.

10.

Remove the wheel nuts, then remove the flat tire. Handle the wheel nuts carefully; they may be hot from driving. Place the flat tire on the ground with the outside surface facing up.

Changing a Flat Tire

12.

Put on the spare tire. Put the wheel nuts back on finger-tight, then tighten them in a crisscross pattern with the wheel nut wrench until the wheel is firmly against the hub. Do not try to tighten them fully.

13.

Lower the vehicle to the ground, and remove the jack.

CONTINUED

219

Main MenuTable of Contentsst０５／０９／０９　１８：２５：５５　３１ＳＮＣ６００　０２２３　

Changing a Flat Tire

WING BOLT

SPACER CONE

19.

Store the jack in the tool case.

Loose items can fly around the interior in a crash and could seriously injure the occupants.

Store the wheel, jack, and tools securely before driving.

20.

Store the center cap in the trunk. Make sure it does not get scratched or damaged.

21.

Lower the trunk floor, and close the trunk lid.

For normal tire

For spare tire

16.

Place the flat tire face down in the spare tire well.

17.

Remove the spacer cone from the wing bolt, turn it over, and put it back on the bolt.

18.

Secure the flat tire by screwing the wing bolt back into its hole.

14.

Tighten the wheel nuts securely in the same crisscross pattern. Have the wheel nut torque checked at the nearest automotive service facility. Tighten the wheel nuts to: 80 lbf·ft (108 N·m , 11 kgf·m)

15.

Remove the center cap before storing the flat tire in the trunk well.

220

Main MenuTable of Contentsst０５／０９／０９　１８：２６：０４　３１ＳＮＣ６００　０２２４　

If the Engine Won’t Start

Diagnosing why the engine won’t start falls into two areas, depending on what you hear when you turn the ignition switch to the START (III) position:

You hear nothing, or almost nothing. The engine’s starter motor does not operate at all, or operates very slowly.

You can hear the starter motor operating normally, or the starter motor sounds like it is spinning faster than normal, but the engine does not start up and run.

Nothing Happens or the Starter Motor Operates Very Slowly When you turn the ignition switch to the START (III) position, you do not hear the normal noise of the engine trying to start. You may hear a clicking sound or series of clicks, or nothing at all. Check these things:

Check the transmission interlock. The transmission must be in Park or neutral or the starter will not operate.

Turn the ignition switch to the ON (II) position. Turn on the headlights, and check their brightness. If the headlights are very dim or do not come on at all, the battery is discharged. See Jump Starting

on page

223

Turn the ignition switch to the START (III) position. If the headlights do not dim, check the condition of the fuses. If the fuses areOK,thereisprobably something wrong with the electrical circuit for the ignition switch or starter motor. You will need a qualified technician to determine the problem (see Emergency Towing

on page

237

).

If the headlights dim noticeably or go out when you try to start the engine, either the battery is discharged or the connections are corroded. Check the condition of the 12 volt battery and terminal connections (see page 212
canthentryjumpstartingthe vehicle from a booster battery (see page

). You

223

).

221

Main MenuTable of Contentsst０５／０９／０９　１８：２６：１０　３１ＳＮＣ６００　０２２５　

If you find nothing wrong, you will need a qualified technician to find the problem. See Towing on page

Emergency 237

If the Engine Won’t Start

The Starter Operates Normally In this case, the starter motor’s speed sounds normal, or even faster than normal, when you turn the ignition switch to the START (III) position, but the engine does not run.

Are you using a properly coded key? An improperly coded key will cause the immobilizer system indicator in the instrument panel to blink rapidly (see page ).

59

Are you using the proper starting Starting the procedure? Refer to Engine 165

on page

Do you have fuel? Check the fuel gauge; the low fuel indicator may not be working.

There may be an electrical problem, such as no power to the fuel pump. Check all the fuses (see page

231

).

222

Main MenuTable of Contentsst０５／０９／０９　１８：２６：１９　３１ＳＮＣ６００　０２２６　

Although this seems like a simple procedure, you should take several precautions.

To jump start your vehicle:

1.

Open the hood, and check the physical condition of the 12 volt battery.

A battery can explode if you do not follow the correct procedure, seriously injuring anyone nearby.

Keep all sparks, open flames, and smoking materials away from the battery.

You cannot start your vehicle by pushing or pulling it.

If a battery sits in extreme cold, the electrolyte inside can f reeze. Attempting to jump start with a f rozen battery can cause it to rupture.

2.

Turn off all electrical accessories: heater, A/C, climate control, audio system, lights, etc. Put the transmission in Park, and set the parking brake.

Jump Starting

BOOSTER BATTERY

The numbers in the illustration show you the order to connect the jumper cables.

3.

＋

) terminal on your

Connect one jumper cable to the positive ( battery. Connect the other end to the positive ( ) terminal on the ＋ booster battery.

CONTINUED

223

Main MenuTable of Contentsst０５／０９／０９　１８：２６：２６　３１ＳＮＣ６００　０２２７　

Jump Starting

If your vehicle’s 12 volt battery is disconnected or goes dead, the IMA battery level gauge reading will not be correct the next time you turn the ignition switch to the ON (II) position. It will show less than the actual level temporarily. It will show the correct level after you drive for at least 30 minutes.

6.

7.

Start the vehicle. If the starter motor still operates slowly, check that the jumper cables have good metal-to-metal contact.

Once your vehicle is running, disconnect the negative cable from your vehicle, then from the booster battery. Disconnect the positive cable from your vehicle, then from the booster battery.

Keep the ends of the jumper cables away from each other and any metal on the vehicle until everything is disconnected. Otherwise, you may cause an electrical short.

4.

−

Connect the second jumper cable to the negative ( ) terminal on the booster battery. Connect the other end to the grounding strap as shown. Do not connect this jumper cable to any other part of the engine.

5.

If the booster battery is in another vehicle, have an assistant start that vehicle and run it at a fast idle.

224

Main MenuTable of Contentsst０５／０９／０９　１８：２６：３４　３１ＳＮＣ６００　０２２８　

The reading on the vehicle’s temperature gauge should stay in the midrange. If it climbs to the red mark, you should determine the reason (hot day, driving up a steep hill, etc.).

If your vehicle overheats, you should take immediate action. The only indicationmaybethetemperature gauge climbing to or above the red mark. Or you may see steam or spray coming from under the hood.

Driving with the temperature gauge reading at the red mark can cause serious damage to the engine.

Steam and spray from an overheated engine can seriously scald you.

Do not open the hood if steam is coming out.

1.

2.

Safely pull to the side of the road. Put the transmission in Park, and set the parking brake. Turn off all accessories, and turn on the hazard warning indicators.

If you see steam and/or spray coming from under the hood, turn off the engine. Wait until you see no more signs of steam or spray, then open the hood.

If the Engine Overheats

3.

4.

5.

If you do not see steam or spray, leave the engine running, and watch the temperature gauge. If the high heat is due to overloading, the engine should start to cool down almost immediately. If it does, wait until the temperature gauge reading comes down to the midpoint, then continue driving.

If the temperature gauge reading stays at the red mark, turn off the engine.

Look for any obvious coolant leaks, such as a split radiator hose. Everything is still extremely hot, so use caution. If you find a leak, it must be repaired before you Emergency continue driving (see Towing ). 237

on page

CONTINUED

225

Main MenuTable of Contentsst０５／０９／０９　１８：２６：４１　３１ＳＮＣ６００　０２２９　

10.

11.

8.

9.

Using gloves or a large heavy cloth, turn the radiator cap counterclockwise, without pushing down, to the first stop. After the pressure releases, push down on the cap, and turn it until it comes off.

Start the engine, and set the temperature control dial to maximum. Add coolant to the radiator up to the base of the filler neck. If you do not have the proper coolant mixture available, you can add plain water. Remember to have the cooling system drained and refilled with the proper mixture as soon as you can.

If the Engine Overheats

6.

7.

If you do not find an obvious leak, check the coolant level in the radiator reserve tank. Add coolant if the level is below the MIN mark.

If there was no coolant in the reserve tank, you may need to add coolant to the radiator. Let the engine cool down until the reading reaches the middle of the temperature gauge or lower before checking the radiator.

Removing the radiator cap while the engine is hot can cause the coolant to spray out, seriously scalding you.

Always let the engine and radiator cool down before removing the radiator cap.

226

Put the radiator cap back on tightly. Run the engine, and watch the temperature gauge. If it goes back to the red mark, the engine needs repair (see Towing on page

Emergency 237

).

If the temperature stays normal, check the coolant level in the radiator reserve tank. If it has gone down, add coolant to the MAX mark. Put the cap back on tightly.

Main MenuTable of Contentsst０５／０９／０９　１８：２６：４８　３１ＳＮＣ６００　０２３０　

This indicator should never come on when the engine is running. If it starts flashing

or stays on, the oil pressure has dropped very low or lost pressure. Serious engine damage is possible, and you should take immediate action.

Running the engine with low oil pressure can cause serious mechanical damage almost immediately. Turn of f the engine as soon as you can saf ely get the vehicle stopped.

1.

2.

3.

4.

Low Oil Pressure Indicator

The engine running generates the oil pressure. When the Auto Idle Stop is activated, the engine is stopped, the oil pressure is dropped, and the low oil pressure indicator does not come on.

Safely pull off the road, and shut off the engine. Turn on the hazard warning indicators.

Let the vehicle sit for a minute. Open the hood, and check the oil level (see page ). An engine very low on oil can lose pressure during cornering and other driving maneuvers.

153

If necessary, add oil to bring the level back to the full mark on the dipstick (see page

189

).

Start the engine, and watch the oil pressure indicator. If it does not go out within 10 seconds, turn off the engine. There is a mechanical problem that needs to be repaired before you can continue driving (see 237

Emergency Towing ).

on page

227

Main MenuTable of Contentsst０５／０９／０９　１８：２６：５４　３１ＳＮＣ６００　０２３１　

Charging System Indicator

If the charging system indicator comes on brightly when the engine is running,

the 12 volt battery is not being charged.

Immediately turn off all electrical accessories. Try not to use other electrically operated controls such as the power windows and rear window defogger. Keep the engine running; starting the engine will discharge the battery rapidly.

Go to a service station or garage where you can get technical assistance.

If the Auto Idle Stop is active for an extended period, the charging system indicator may come on. If it happens, start the engine.

The charging system indicator may also come on if the Integrated Motor Assist (IMA) battery charge drops below a desired level and the engine starts to recharge the battery.

This indicator may blink after you start the vehicle in the morning when the temperature is below 20
− °F ( 30°C). It will stop blinking when the IMA battery warms up.

−

228

Main MenuTable of Contentsst０５／０９／０９　１８：２７：０１　３１ＳＮＣ６００　０２３２　

If the indicator comes on while driving, it means one of the engine’s emissions

control systems may have a problem. Even though you may feel no difference in your vehicle’s performance, it can reduce your fuel economy and cause increased emissions. Continued operation may cause serious damage.

If you have recently refueled your vehicle, the indicator coming on could be due to a loose or missing fuel fill cap. You will also see a ‘‘CHECK FUEL CAP’’ message on the information display. Tighten the cap until it clicks at least once (see page ). Tightening the cap will not turn the indicator off immediately; it can take several days of normal driving.

151

Malfunction Indicator Lamp

If the indicator comes on repeatedly, even though it may turn off as you continue driving, have the vehicle checked by the dealer as soon as possible.

If the battery in your vehicle has been disconnected or gone dead, these codes are erased. It takes at least three days of driving under various conditions to set the codes again.

If you keep driving with the Malf unction Indicator Lamp on, you can damage your vehicle’s emissions controls and engine. Those repairs may not be covered by your vehicle’s warranties. This indicator may also come on with the ‘‘D’’ indicator.

Readiness Code Your vehicle has certain ‘‘readiness codes’’ that are part of the on-board diagnostics for the emissions systems. In some states, part of the emissions testing is to make sure these codes are set. If they are not set, the test cannot be completed.

To check if they are set, turn the ignition switch to the ON (II) position, without starting the engine. The malfunction indicator lamp will come on for 20 seconds. If it then goes off, the readiness codes are set. If it blinks five times, the readiness codes are not set. If possible, do not take your vehicle for a state emissions test until the readiness codes are set. Refer to Emissions Testing information (see page

State for more ).

250

229

Main MenuTable of Contentsst０５／０９／０９　１８：２７：０８　３１ＳＮＣ６００　０２３３　

Brake System Indicator

However, if the brake pedal does not feel normal, you should take immediate action. A problem in one part of the system’s dual circuit design will still give you braking at two wheels. You will feel the brake pedal go down much farther before the vehicle begins to slow down, and you will have to press harder on the pedal.

Slow down by shifting to a lower gear, and pull to the side of the road when it is safe. Because of the long distance needed to stop, it is hazardous to drive the vehicle. You should have it towed and repaired as soon as possible (see Towing 237

Emergency ).

on page

If you must drive the vehicle a short distance in this condition, drive slowly and carefully.

If the ABS indicator comes on with the brake system indicator, have your vehicle inspected by your dealer immediately.

If the brake system indicator (amber) comes on with the parking brake system indicator (red) with the parking brake released, there may be a malfunction with the power-assist feature. When the power-assist feature malfunctions, the brake indicator (red) comes on and a buzzer sounds for a second. The power-assist feature may stop when the brake effect is weak. Stop your vehicle immediately at a safe place and contact a dealer.

U.S.

Canada

The brake system indicator normally comes on when you turn the ignition switch to the ON (II) position and as a reminder to check the parking brake. It will stay on if you do not fully release the parking brake.

If the brake system indicator comes on while driving, the brake fluid level is probably low. Press lightly on the brake pedal to see if it feels normal. If it does, check the brake fluid level thenexttimeyoustopataservice station (see page

196

).

If the fluid level is low, take your vehicle to a dealer, and have the brake system inspected for leaks or worn brake pads.

230

Main MenuTable of Contentsst０５／０９／１０　１４：３７：０７　３１ＳＮＣ６００　０２３４　

INTERIOR

UNDER-HOOD (PRIMARY)

UNDER-HOOD (SECONDARY)

FUSE LABEL

The vehicle’s fuses are contained in three fuse boxes.

The interior fuse box is underneath the steering column.

TAB

The primary and secondary under- hood fuse boxes are in the engine compartment on the driver’s side.

Fuses

231

Main MenuTable of Contentsst０５／０９／０９　１８：２７：２２　３１ＳＮＣ６００　０２３５　

Fuses

and

Checking and Replacing Fuses If something electrical in your vehicle stops working, the first thing youshouldcheckforisablownfuse. Determine from the chart on pages or the diagram on the 235
fuse box lid, which fuses control that device. Check those fuses first, but check all the fuses before deciding that a blown fuse is the cause. Replace any blown fuses, and check if the device works.

236

FUSE

BLOWN

BLOWN

1.

Turn the ignition switch to the LOCK (0) position. Make sure the headlights and all other accessories are off.

2.

Remove the cover from the fuse box.

3.

Check each of the large fuses in the primary under-hood fuse box by looking through the top at the wire inside. Removing these fuses requires a Phillips-head screwdriver.

232

Main MenuTable of Contentsst０５／０９／０９　１８：２７：２８　３１ＳＮＣ６００　０２３６　

BLOWN

FUSE PULLER

4.

Check the smaller fuses in the under-hood fuse boxes and all the fuses in the interior fuse box by pulling out each one with the fuse puller provided in the primary under-hood fuse box.

5.

Look for a blown wire inside the fuse. If it is blown, replace it with one of the spare fuses of the same rating or lower. The spare fuses are provided back of the under- hood fuse cover.

Fuses

If you cannot drive the vehicle without fixing the problem, and you do not have a spare fuse, take a fuse of the same rating or a lower rating from one of the other circuits. Make sure you can do without that circuit temporarily (such as the accessory power socket or radio).

If you replace the blown fuse with a spare fuse that has a lower rating, it might blow out again. This does not indicate anything wrong. Replace the fuse with one of the correct rating as soon as you can.