1993 Honda Civic DEL SOL Owners Manual

BLADE

BLADE

5. Slide the new wiper blade into the holder until the tabs lock.

Windshield Wipers

6. Slide the blade assembly onto the wiper arm. Make sure it locks in place.

7. Lower the wiper arm down

against the windshield.

3. Remove the blade from its holder by grasping the tabbed end of the blade. Pull firmly until the tabs come out of the holder.

REINFORCEMENT

4. Examine the new wiper blades. If they have no plastic or metal rein- forcement along the back edge, remove the metal reinforcement strips from the old wiper blade and install them in the slots along the edge of the new blade.

Maintenance

Air Conditioning (Optional)

Your car's air conditioning is a sealed system. Any major mainte- nance, such as recharging, should be done by a qualified technician. There are a couple of things you can do to make sure the air condi- tioning works efficiently.

AIR CONDITIONING CONDENSER

light spray from a hose or a soft brush to remove them.

NOTICE

The condenser and radiator fins bend easily. Only use a low- pressure spray or soft-bristle brush to clean them.

If the air conditioning does not get as cold as before, it is probably because some of the refrigerant has leaked from the system. Have your dealer check the system for leaks and recharge the system with Refrigerant 12 (R-12). Charging quantity: 600—650 g (21.2—23.0 oz)

Run the air conditioning at least once a week during the cold weather months. Run it for at least ten minutes while you are driving at a steady speed with the engine at normal operating temperature. This circulates the lubricating oil contained in the refrigerant.

NOTICE

Whenever you have the air condi- tioning system serviced, make sure the service facility uses a refrige- rant recycling system. This system captures the refrigerant for reuse. Releasing refrigerant into the at- mosphere can damage the environ- ment.

Periodically check the engine's radiator and air conditioning condenser for leaves, insects, and dirt stuck to the front surface. These block the air flow and reduce cooling efficiency. Use a

Maintenance

Engine Belts

ALTERNATOR BELT

If you see signs of wear or loose- ness, have your dealer adjust or replace the belts. Your dealer will check these belts as part of the normal scheduled maintenance.

POWER STEERING BELT Check the condition of the two engine belts. Examine the edges of each belt for cracks or fraying. Check the tension of each belt by pushing on it with your thumb midway between the pulleys. The belts should have the following "play" or deflection.

Alternator belt: 7.0 — 10.5 mm (0.28 — 0.41 in) Power steering belt: 8.0 — 12.0 mm (0.31 — 0.47 in)

Engine Belts, Tires

Tires Check the inflation and condition of your car's tires at least once a month.

Inflation Check the pressure in the tires when they are cold. This means the car has been parked for at least three hours. If you have to drive the car before checking the tire pressure, the tires can still be considered "cold" if you drive less than 1.6 km (1 mile).

If you check the pressure when the tires are hot (the car has been driven several miles), you will see readings 28 to 41 kPa (0.3 to 0.4
kg/cm2,4 to 6 psi) higher than the cold reading. This is normal. Do not let air out to match the specified cold pressure. The tire will be underinflated.

CONTINUED

Maintenance

Tires

The correct cold tire pressures are: (S)

Front/Rear: 220 kPa (2.2 kg/cm2 , 32 psi)

(Si)

Front/Rear: 200 kPa (2.0 kg/cm2 , 29 psi)

Compact spare:

415 kPa (4.15 kg/cm2 , 60 psi)

Maintenance

Keeping the tires properly inflated provides you with the best combi- nation of riding comfort, handling and tread life. Underinflated tires wear unevenly, reduce your car's handling, and are more likely to fail because of higher temperatures. Overinflated tires make your car ride more harshly, are more prone to damage from road hazards, and wear unevenly.

Inspection Every time you check inflation pressures, you should also examine the tires for damage, foreign objects, and wear. You should look for:

Bumps or bulges in the tread or side of the tire. Replace the tire if you find either of these condi- tions. Cuts, splits, or cracks in the side of the tire. Replace the tire if you can see fabric or cord. Excessive tread wear.

TIRE INFORMATION LABEL

These pressures are also given on the tire information label in the glove box. Remember to check the pressure in the spare tire at the same time.

You should get your own tire pressure gauge and use it at all times. That makes it easier for you to tell if a pressure loss is caused by a tire problem and not a variation between gauges.

INDICATOR LOCATION MARKS

TREAD WEAR INDICATORS Your car's tires have wear indica- tors molded into the tread. When the tread wears down to that point, you will see a 12.7 mm (1/2 inch) wide band running across the tread. This shows there is less than 1.6
mm (1/16 inch) of tread left on the tire. A tire that is this worn gives very little traction on wet roads. You should replace the tire if you can see the tread wear indicator in three or more places around the tire.

Maintenance In addition to proper inflation, correct wheel alignment helps to decrease tire wear. You should get your car's wheel alignment check- ed every 12 months or 24,000 km (15,000 miles).

The tires were properly balanced by the factory. They may need to be rebalanced at some time before they are worn out. Have your dealer check the tires if you feel a consistent vibration while driving. A tire should always be rebalanced if it is removed from the wheel. Make sure the installer balances the wheels when you have new tires installed. This increases riding comfort and tire life.

NOTICE

(Si model) Improper wheel weights can damage your car's aluminum

Tires

wheels. Use only genuine Honda wheel weights for balancing.

Tire Rotation

Front

To help increase tire life and distribute wear more evenly, you should have the tires rotated every 12,000 km (7,500 miles). Move the tires to the positions shown in the chart each time they are rotated.

Maintenance

Tires

Replacing Tires The tires that came with your Honda were selected to match the performance capabilities of the car and provide the best combination of handling, ride comfort, and long life. You should replace them with radial tires of the same size, load range, and speed rating. Mixing radial and bias-ply or bias-belted tires on your car can reduce its braking ability, traction, and steering accuracy. It is best to replace all four tires at the same time. If that is not possi- ble or necessary, then replace the two front tires or the two rear tires as a pair. Replacing just one tire can seriously affect your car's han- dling. If you ever need to replace a wheel, make sure you use an identical style wheel that originally came on your Honda. Replacement wheels are available at your Honda dealer.

Maintenance

Treadwear The treadwear grade is a compara- tive rating based on the wear rate of the tire when tested under con- trolled conditions on a specified government test course. For exam- ple, a tire graded 150 would wear one and one half (1-1/2) times as well on the government course as a tire graded 100. The relative per- formance of tires depends upon the actual conditions of their use, how- ever, and may depart significantly from the norm due to variations in driving habits, service practices and differences in road character- istics and climate.

Wheels and Tires

Wheel Size: (S)

13x5J

(Si)

14x51/2JJ

Tire Sizes: (S)

(Si)

P175/70R1382S

P185/60R1482H

DOT Tire Quality Grading (US Cars) The tires on your car meet all U.S. Federal Safety Requirements. All tires are also graded for treadwear, traction, and temperature perform- ance according to Department of Transportation (DOT) standards. The following explains these gradings.

Traction The traction grades, from highest to lowest, are A, B, and C, and they represent the tire's ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance.

Warning: The traction grade as- signed to this tire is based on brak- ing (straight ahead) traction tests and does not include cornering (turning) traction.

Temperature The temperature grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law.

Tires

Warning: The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading either separately or in combination, can cause heat build-up and possible tire failure.

Maintenance

Tires

Winter Driving Tires that are marked "M+S" or "All Season" on the sidewall have an all-weather tread design. They should be suitable for most winter driving conditions. Tires without these markings are designed for optimum traction in dry conditions. They may not provide adequate performance in winter driving. For the best performance in snowy or icy conditions, you should install snow tires or tire chains. They may be required by local laws under certain conditions.

Maintenance

When installing chains, follow the manufacturer's instructions and mount them as tightly as you can. Drive slowly with chains installed. If you hear the chains contacting the body or chassis, stop and tighten them. If they still make contact, slow down until it stops. Remove the chains as soon as you begin driving on cleared roads.

NOTICE

Chains of the wrong size or that are improperly installed can damage your car's brake lines, suspension, body, and wheels. Stop driving if you hear the chains hitting any part of the car.

Snow Tires If you mount snow tires on your Honda, make sure they are radial tires of the same size and load range as the original tires. Mount snow tires on all four wheels to balance your car's handling in all weather conditions. Keep in mind the traction provided by snow tires on dry roads may not be as high as your car's original-equipment tires. You should drive cautiously even when the roads are clear. Check with the tire dealer for maximum speed recommendations.

Tire Chains Mount snow chains on your car when warranted by driving condi- tions or required by local laws. Make sure the chains are the cor- rect size for your tires. Install them only on the front tires. If metal chains are used, they must be SAE class"S". Cable type traction de- vices can also be used.

Replacing a Headlight Bulb Your car has halogen headlight bulbs, one on each side. When replacing a bulb, handle it by its steel base and protect the glass from contact with your skin or hard objects. If you touch the glass, clean it with denatured alcohol and a clean cloth.

NOTICE

Halogen headlight bulbs get very hot when lit. Oil, perspiration, or a scratch on the glass can cause the bulb to overheat and shatter.

Check the operation of your car's exterior lights at least once a month. A burned out bulb can create an unsafe condition by reducing your car's visibility and the ability to signal your intentions to other drivers. Check the following:

Headlights (low and high beam) Auxiliary lights Parking lights Taillights Brake lights Turn signals Back-up lights Hazard light function License plate light Side marker lights Daytime running lights (Canadian cars)

If you find any bulbs are burned out, replace them as soon as possible. Refer to the chart on page 169 to determine what type of replacement bulb is needed.

Lights

BULB

CONNECTOR

HOLD-DOWN WIRE

1. Open the hood.

If you need to change the headlight bulb on the passenger's side, remove the air intake tube by pulling it straight up.

2. Remove the electrical connector

from the bulb by pulling the connector straight back.

CONTINUED

Maintenance

3. Remove the burned-out bulb

from its socket. To remove the bulb, push it in slightly and turn it counterclockwise.

4. Insert the new bulb in the socket.

Reinstall the socket.

5. Test the bulb by turning on the

headlights (low beam) and auxiliary lights.

Lights

3. Remove the rubber weather seal

by pulling on the tab.

Replacing an Auxiliary Light Bulb

4. Unclip the end of the hold-down wire from its slot. Pivot it out of the way and remove the bulb.

5. Insert the new bulb into the hole, making sure the tabs are in their slots. Pivot the hold-down wire back in place and clip the end into the slot.

6. Push the rubber weather seal

over the bulb.

7. Push the electrical connector onto the tabs of the new bulb. Turn on the headlights to test the new bulb.

8. (Passenger's side)

Reinstall the air intake tube.

Maintenance

The auxiliary lights are located next to the headlights.

1. Open the hood.

2. Remove the socket by turning it one-quarter turn counterclock- wise.

Replacing the Front Side Marker/Turn Signal and Parking Light Bulb

SOCKET

SCREW

BULB

1. Use a Phillips-head screwdriver

to remove the screw from the top of the fender.

2. Move the side marker light

assembly forward until it slides out of the body.

3. Turn the socket one-quarter turn

counterclockwise to remove it from the lens.

Lights

4. Remove the bulb by pushing it in

slightly and turning it counter- clockwise.

5. Install the new bulb in the socket.

Turn it clockwise to lock it in place.

6. Insert the socket back into the

lens. Turn it clockwise to lock it in place.

7. Turn on the parking lights to

make sure the new bulb works.

8. To reinstall the light assembly in

the fender, line up the guide on the assembly with the metal tab next to the headlight and line up the fingers on the light assembly with the holes in the fender. Push the light assembly straight back.

9. Install the mounting screw and

tighten it securely.

Maintenance

Lights

Replacing Rear Bulbs

4. Install the new bulb in the socket.

Insert the socket back in the taillight assembly and turn it clockwise to lock it in place.

5. Test the new bulb. Reinstall the

cover over the taillight assembly.

3. To remove the tail/stoplight bulb,

back-up light bulb or the turn signal bulb, push it in slightly and turn it counterclockwise. To remove the side marker bulb, pull it straight out of the socket.

1. Open the trunk and the taillight

assembly cover. When replacing a bulb in the right assembly, remove the jack first.

2. Determine which of the four

bulbs is burned out: tail/stoplight, back-up light, turn signal, or side marker. Remove the socket for that bulb by turning it counter- clockwise.

Maintenance

Replacing a Rear License Bulb

4. Pull the bulb straight out of the

socket.

Replacing Interior and Trunk Light Bulbs

Lights

INTERIOR LIGHT

5. Install the new bulb. Test it to

make sure it works.

6. Reinstall the light assembly on

the bracket. Install the mounting screws and tighten them secu- rely.

1. Open the trunk.

Use a Phillips-head screwdriver to remove the two mounting screws.

2. Pull the assembly away from the

bracket.

3. Remove the socket from the light assembly by turning it counterclockwise.

1. Remove the lens by carefully

prying on the edge of the lens in the middle with a fingernail file or a small flat-tip screwdriver. Do not pry on the edge of the housing around the lens.

CONTINUED

Maintenance

Lights

TRUNK LIGHT

2. Remove the bulb by pulling it straight out of its metal tabs.

3. Push the new bulb into the metal tabs. Snap the lens back in place.

Maintenance

Storing Your Car

If you need to park your car for an extended period (more than 1
month), there are several things you should do to prepare it for storage. Proper preparation helps prevent deterioration and makes it easier to get your car back on the road. It is best to store your car indoors if at all possible.

Block the rear wheels.

If the car is to be stored for a longer period, it should be supported on jackstands so the tires are off the ground.

Leave one window open slightly (if the car is being stored indoors).

Fill the fuel tank.

Disconnect the battery.

If you store your car for 12 months or longer, have your Honda dealer perform the inspections called for in the 24 months/48,000 km (30,000
miles) maintenance schedule as soon as you take it out of storage (see page 95). The replacements called for in the maintenance schedule are not needed unless the car has actually reached that time or mileage.

Change the engine oil and filter (see page 103).

Wash and dry the exterior completely.

Clean the interior. Make sure the carpeting, floor mats, etc. are completely dry.

Leave the parking brake off. Put the transmission in Reverse (manual) or Park (automatic).

Cover the car with a "breathable" car cover, one made from a porous material such as cotton. Nonporous materials, such as plastic sheeting, trap moisture which can damage the paint.

If possible, run the engine for a while periodically (preferably once a month).

Maintenance

Appearance Care

Regular cleaning and polishing of your Honda helps to keep it "new" looking. This section gives you hints on how to clean and preserve your car's appearance: the paint, brightwork, wheels and interior. Also included are several things you can do to help prevent corro- sion.

Exterior Care................................ 138
Washing...................................... 138
Waxing....................................... 139
Paint Touch-up......................... 139
Aluminum Wheels................... 140
Interior Care.................................. 141
Carpeting................................... 141
Fabric...................................... 141
Vinyl............................................ 141
Seat Belts................................... 141
Windows..................................... 142
Air Fresheners.......................... 142
Corrosion Protection................... 142
Body Repairs................................. 143

Appearance Care

Exterior Care

Washing Frequent washing helps preserve your car's beauty. Dirt and grit can scratch the paint, while tree sap and bird droppings can perma- nently ruin the finish.

Wash your car in a shady area, not in direct sunlight. If the car is parked in the sun, move it into the shade and let the exterior cool down before you start.

NOTICE

Chemical solvents and strong cleaners can damage the paint, metal, and plastic on your car. Only use the solvents and cleaners recommended in this Owner's Manual.

Appearance Care

• When you have washed and

rinsed the whole exterior, dry it with a chamois or soft towel. Letting it air-dry will cause dulling and water spots.

As you dry the car, inspect it for chips and scratches that could allow corrosion to start. Repair them with touch-up paint (see page 139).

Rinse the car thoroughly with cool water to remove loose dirt.

Fill a bucket with cool water. Mix in a mild detergent, such as dishwashing liquid or a product made especially for car washing.

Wash the car, using the water and detergent solution and a soft- bristle brush, sponge, or soft cloth. Start at the top and work your way down. Rinse frequently.

Check the body for road tar, tree sap, etc. Remove these stains with tar remover or turpentine. Rinse it off immediately so it does not harm the finish. Remem- ber to re-wax these areas, even if the rest of the car does not need waxing.

Waxing Always wash and dry the whole car before waxing it. You should wax your car, including the metal trim, whenever water sits on the surface in large patches. It should form into beads or droplets after waxing.

You should use a quality liquid or paste wax. Apply it according to the instructions on the container. In general, there are two types of products:

Waxes — A wax coats the finish and protects it from damage by exposure to sunlight, air pollution, etc. You should use a wax on your Honda when it is new.

Polishes — Polishes and cleaner/ waxes can restore the shine to paint that has oxidized and lost some of its shine. They normally contain mild abrasives and solvents that remove the top layer of the finish. You should use a polish on your Honda if the finish does not have its original shine after using a wax.

Cleaning tar, insects, etc. with removers also takes off the wax. Remember to re-wax those areas, even if the rest of the car does not need waxing.

Exterior Care

Paint Touch-up Your dealer has touch-up paint to match your car's color. The color code is printed on a sticker on the driver's door jamb. Take this code to your dealer so you are sure to get the correct color.

CONTINUED

Appearance Care

Examine the chip or scratch closely before repairing it. If it does not go down to bare metal, clean it with soap and water and apply the touch-up paint. If it does go to the metal, apply a coat of primer first. After this dries, apply the touch-up paint. Build up the paint in the damaged area to the level of the surrounding paint. Several thin coats of paint are better than one thick coat.

Aluminum Wheels Clean your Honda's aluminum alloy wheels as you do the rest of the exterior. Wash them with the same solution, and rinse them thoroughly.

The wheels have a protective clear- coat that keeps the aluminum from corroding and tarnishing. Using harsh chemicals, including some commercial wheel cleaners, or stiff brushes can damage this clear-coat. Only use a mild detergent and soft brush or sponge to clean the wheels.

Exterior Care

TOUCH-UP PAINT

Inspect your car for chipped or scratched paint every time you wash it. Repair it as soon as possible to prevent corrosion. Use the touch-up paint on small chips and scratches. More extensive damage should be repaired by a professional.

Appearance Care

Carpeting Vacuum the carpeting frequently to remove dirt. Ground-in dirt will make the carpet wear out faster. Periodically shampoo the carpet to keep it looking new. Use one of the foam-type carpet cleaners on the market. Follow the instructions that come with the cleaner, apply- ing it with a sponge or soft brush. Keep the carpeting as dry as possi- ble by not adding water to the foam.

Fabric Vacuum dirt and dust out of the material frequently. For general cleaning, use a solution of mild soap and lukewarm water, letting it air dry. To clean off stubborn spots, use a commercially-available fabric cleaner. Test it on a hidden area of the fabric first, to make sure it does not bleach or stain the fabric. Follow the instructions that come with the cleaner.

Interior Care

Vinyl Remove dirt and dust with a vacuum cleaner. Wipe the vinyl with a soft cloth dampened in a solution of mild soap and water. Use the same solution with a soft- bristle brush on more difficult spots. You can also use commercially- available spray or foam-type vinyl cleaners.

Seat Belts If your seat belts get dirty, you can use a soft brush with a mixture of mild soap and warm water to clean them. Do not use bleach, dye, or cleaning solvents. They can weaken the belt material. Let the belts air-dry before you use the car.

Appearance Care

Interior Care, Corrosion Protection

Windows Clean the windows, inside and out, with a commercially-available glass cleaner. You can also use a mixture of one part white vinegar to ten parts water. This will remove the haze that builds up on the inside of the windows. Use a soft cloth or paper towels to clean all glass and clear plastic surfaces.

NOTICE

The rear window defogger wires are bonded to the inside of the glass. Wiping vigorously up-and-down can dislodge and break the defog- ger wires. When cleaning the rear window, use gentle pressure and wipe side-to-side.

Appearance Care

Air Fresheners If you want to use an air freshener/ deodorizer in the interior of your car, it is best to use a solid type. Some liquid air fresheners contain chemicals that may cause parts of the interior trim and fabric to crack or discolor.

If you use a liquid air freshener, make sure you fasten it securely so it does not spill as you drive.

Corrosion Protection Two factors normally contribute to causing corrosion in your car:

1. Moisture trapped in body cavi- ties. Dirt and road salt that col- lects in hollows on the underside of the car stays damp, promoting corrosion in that area.

2. Removal of paint and protective

coatings from the exterior and underside of the car.

Many corrosion-preventive mea- sures are built into your Honda. You can help keep your car from corroding by performing some simple periodic maintenance:

Repair chips and scratches in the paint as soon as you discover them.

Corrosion Protection, Body Repairs

Body Repairs Body repairs affect your car's resistance to corrosion. If your car needs repairs after a collision, pay close attention to the parts used in the repair and the quality of the work.

Make sure the repair facility uses genuine Honda replacement body parts. Some companies make sheetmetal pieces that seem to duplicate the original Honda body parts, but are actually inferior in fit, finish, and quality. Once installed, they do not give the same high- quality appearance and level of corrosion resistance.

When reporting your collision to the insurance company, tell them you want genuine Honda parts used in the repair. Although most insurers recognize the higher quality of original parts, some may try to specify that the repairs be done with the "lowest cost" parts available. You should investigate this before any repairs are begun.

Take your car to your authorized Honda dealer for inspection after the repairs are completed. He can make sure that quality materials were used, and that corrosion- preventive coatings were applied to all repaired and replaced parts.

Inspect and clean out the drain holes in the bottom of the doors and body.

Check the floor coverings for dampness. Carpeting and floor mats may remain damp for a long time, especially in winter. This dampness can eventually cause the floor panels to corrode.

Use a high-pressure spray to clean the underside of your car. This is especially important in areas that use road salt in winter. It is also a good idea in humid climates and areas subject to salt air.

Have the corrosion-preventive coatings on the underside of your car inspected and repaired periodically.

Appearance Care

Taking Care of the Unexpected

This section covers the more- common problems that motorists experience with their cars. It gives you information about how to safely evaluate the problem and what to do to correct it. If the problem has stranded you on the side of the road, you may be able to get going again. If not, you will also find instructions on getting your car towed.

Compact Spare Tire..................... 146
Changing a Flat Tire................... 147
If Your Engine Won't Start........ 153
Nothing Happens...................... 153
The Starter Operates

Normally................................ 154
Jump Starting............................... 154
If Your Engine Overheats.......... 156
Low Oil Pressure.......................... 158
Charging System Indication...... 159
Malfunction Indicator Light/

Check Engine Light................. 160
Fuses............................................... 161
Checking and Replacing......... 162
Towing........................................... 164

Taking Care of the Unexpected

Compact Spare Tire

Your car has a compact spare tire that takes up less space. Use this spare tire as a temporary replace- ment only. Get your regular tire repaired or replaced and put back on your car as soon as you can.

Check the inflation pressure of the compact spare tire every time you check the other tires. It should be inflated to: 415 kPa (4.15 kg/cm2 , 60 psi)

Taking Care of the Unexpected

Follow these precautions whenever you are using the compact spare tire:

INDICATOR LOCATION MARK

Do not exceed 50 mph (80 km/h) under any circumstances.

This tire gives a harsher ride and less traction on some road sur- faces than the regular tire. Use greater caution while driving on this tire.

Do not mount snow chains on the compact spare.

The wheel of the compact spare tire is designed especially to fit your car. Do not use your spare tire on another car unless it is the same make and model.

TREAD WEAR INDICATOR BAR

The compact spare tire has a shorter tread life than a regular tire. Replace it when you can see the tread wear indicator bars. The replacement should be the same size and design tire, mounted on the same wheel. The compact spare tire is not designed to be mounted on a regular wheel, and the com- pact wheel is not designed for mounting a regular tire.

If you have a flat tire while driving, stop in a safe place to change it. Stopping in traffic or on the shoul- der of a busy road is dangerous. Drive slowly along the shoulder until you get to an exit or an area to stop that is far away from the traf- fic lanes.

The car can easily roll off the jack, seriously injuring anyone underneath.

Follow the directions for chang- ing a tire exactly, and never get under the car when it is supported only by the jack.

1. Park the car on firm, level

ground away from traffic. Turn on the hazard warning lights and turn the ignition to LOCK (0).

Changing a Flat Tire

TOOL KIT

JACK

ROOF HOLDER SPARE TIRE 2. Put the transmission in Park

4. Take the tool kit out of the trunk.

(automatic) or Reverse (manual). Set the parking brake.

3. Open the trunk and lift up the

roof holder. Raise the trunk floor by lifting up on the back edge.

5. Unscrew the wing bolt and take

the spare tire out of its well.

CONTINUED

Taking Care of the Unexpected

Changing a Flat Tire

JACK

SCREWDRIVER

6. Turn the jack's end bracket

counterclockwise to loosen it, then remove the jack.

CENTER CAP

7. On the Si model

Remove the center cap from the wheel with a screwdriver (not included in tool kit) or coin.

8. Loosen the four wheel nuts 1/2

turn with the wheel wrench.

Taking Care of the Unexpected

WHEEL EXTENSION WRENCH 10.Use the extension and wheel

wrench as shown to raise the car until the flat tire is off the ground.

JACKING POINT 9. Locate the jacking point nearest the tire you need to change. It is pointed to by an arrow molded into the underside of the body. Place the jack under the jacking point. Turn the end bracket clockwise until the top of the jack contacts the jacking point. Make sure the jacking point tab is resting on the jack notch.

Changing a Flat Tire

WHEEL NUTS

WHEEL COVER

11.Remove the wheel nuts and

wheel cover. The wheel cover cannot be removed without first removing the wheel nuts. Do not attempt to forcibly pry the wheel cover off with a screwdriver or other tool.

CONTINUED

Taking Care of the Unexpected

Changing a Flat Tire

BRAKE HUB

12.Remove the flat tire. Tempo- rarily place the flat tire on the ground with the outside surface of the wheel facing up. The outside surface contacting the ground could damage the wheel surface.

13.Before mounting the spare tire, wipe any dirt off the mounting surface of the wheel and hub with a cloth.

14.Put on the spare tire. Put the

wheel nuts back on finger-tight, then tighten them in a crisscross pattern with the wheel wrench until the wheel is firmly against the hub. Do not try to tighten them fully.

Taking Care of the Unexpected

Changing a Flat Tire

WING BOLT

SPACER CONE

15.Lower the car to the ground and

remove the jack.

16.Tighten the wheel nuts securely in the same crisscross pattern. Have the wheel nut torque check- ed at the nearest automotive service facility. Tighten the wheel nuts to: 110 N.m (11 kg-m, 80 Ib-ft)

17.Place the flat tire face down in

the spare tire well.

18.Remove the spacer cone from the wing bolt, turn it over, and put it back on the bolt.

19.Secure the flat tire by screwing the wing bolt back into its hole.

CONTINUED

Taking Care of the Unexpected

Changing a Flat Tire

20.Store the jack in its holder with

the end bracket facing to the rear. Turn the jack's end bracket to lock it in place. Replace the cover. Store the tool kit.

21.Store the wheel cover or center cap in the trunk. Make sure they do not get scratched or damaged.

22.Reinstall the floor lid.

23.Lower the roof holder, then close

the trunk lid.

Taking Care of the Unexpected

Diagnosing why your engine won't start falls into two areas, depending on what you hear when you turn the key to START (III):

You hear nothing, or almost nothing. The engine's starter motor does not operate at all, or operates very slowly.

You can hear the starter motor operating normally, but the engine does not start up and run.

If Your Engine Won't Start

Nothing Happens or the Starter Motor Operates Very Slowly When you turn the ignition switch to START (III), you do not hear the normal noise of the engine trying to start. You may hear a clicking sound or series of clicks, or nothing at all. Check these things:

Check the transmission interlock. If you have a manual trans- mission, the clutch pedal must be pushed all the way to the floor or the starter will not operate. With an automatic transmission, it must be in Park or Neutral.

Turn the ignition switch to ON (II). Turn on the headlights and check their brightness. If the headlights are very dim or don't light at all, the battery is dis- charged. See Jump Starting on page 154.

Turn the ignition switch to START (III). If the headlights do not dim, check the condition of the fuses. If the fuses are OK, there is probably something wrong with the electrical circuit for the ignition switch or starter motor. You will need a qualified technician to determine the problem. (See Towing on page 164.)

If the headlights dim noticeably or go out when you try to start the engine, either the battery is discharged or the connections are corroded. Check the condi- tion of the battery and terminal connections (see page 117). You can then try jump starting the car from a booster battery (see page 154).

Taking Care of the Unexpected

If Your Engine Won't Start, Jump Starting

The Starter Operates Normally In this case, the starter motor sounds normal when you turn the ignition switch to START (III), but the engine does not run.

Are you using the proper starting procedure? Refer to Starting the Engine on page 81 .

Do you have gas? Turn the ignition switch to ON (II) for a minute and watch the fuel gauge.

There may be an electrical problem, such as no power to the fuel pump. Check all the fuses (see page 161).

Jump Starting If your car's battery has run down, you may be able to start the engine by using a booster battery. Although this seems like a simple procedure, there are several precau- tions you should take. Follow the directions closely.

A battery can explode if you do not follow the correct pro- cedure, seriously injuring any- one nearby.

Keep all sparks, open flames, and smoking materials away from the battery.

If you find nothing wrong, you will need a qualified technician to find the problem. See Towing on page 164.

You cannot start a Honda with an automatic transmision by pushing or pulling it.

To jump start your car:

1. Open the hood and check the

physical condition of the battery (see page 117). In very cold weather, check the condition of the electrolyte. If it seems slushy or like ice, do not try jump starting until it thaws.

NOTICE

If a battery sits in extreme cold, the electrolyte inside can freeze. Attempting to jump start with a frozen battery can cause it to rupture or explode.

2. Turn off all the electrical acces-

sories: heater, A/C, stereo system, lights, etc. Put the transmission in Neutral or Park and set the parking brake.

Taking Care of the Unexpected

Jump Starting

3. Connect one jumper cable to the

positive (+) terminal on the booster battery. Connect the other end to the positive (+) terminal on your Honda's battery.

4. Connect the second jumper cable

to the negative (—) terminal on the booster battery. Connect the other end to the grounding strap as shown. Do not connect this jumper cable to any other part of the engine.

5. If the booster battery is in

another car, have an assistant start that car and run it at a fast idle.

BOOSTER BATTERY 6. Start your car. If the starter

motor still operates slowly, check the jumper cable connections to make sure they have good metal- to-metal contact.

7. Once your car is running,

disconnect the negative cable from your car, then from the booster battery. Disconnect the positive cable from your car, then the booster battery.

Taking Care of the Unexpected

If Your Engine Overheats

The pointer of your car's tempera- ture gauge should stay in the mid- range under most conditions. It may go higher if you are driving up a long steep hill on a very hot day. If it climbs to the red mark, you should determine the reason.

NOTICE

Driving with the temperature gauge pointer at the red mark can cause serious damage to your engine.

Taking Care of the Unexpected

Your car can overheat for several reasons, such as lack of coolant or a mechanical problem. The only indication may be the temperature gauge climbing to or above the red mark. Or you may see steam or spray coming from under the hood. In either case, you should take immediate action.

Steam and spray from an over- heated engine can seriously scald you.

Do not open the hood if steam is coming out.

1. Safely pull to the side of the road.

Put the transmission in neutral or Park and set the parking brake. Turn off the heating and cooling system and all other accessories. Turn on the hazard warning indicators.

2. If you see steam and/or spray coming from under the hood, turn off the engine.

3. If you do not see steam or spray,

leave the engine running and watch the temperature gauge. If the high heat is due to overload- ing (climbing a long, steep hill on a hot day with the A/C running, for example), the engine should start to cool down almost immedi- ately. If it does, wait until the temperature gauge comes down to the midpoint then continue driving.

4. If the temperature gauge stays at the red mark, turn off the engine.

5. Wait until you see no more signs of steam or spray, then open the hood.

6. Look for any obvious coolant leaks, such as a split radiator hose. Everything is still extreme- ly hot, so use caution. If you find a leak, it must be repaired before you continue driving (see Towing on page 164).

7. If you don't find an obvious leak,

check the coolant level in the radiator reserve tank (see page 105). If the level is below the MIN mark, add coolant to half- way between the MIN and MAX marks.

8. If there was no coolant in the

reserve tank, you may also have to add coolant to the radiator.

Let the engine cool down until the pointer reaches the middle of the temperature gauge, or lower, before checking the radiator.

Removing the radiator cap white the engine is hot can cause the coolant to spray out, seriously scalding you.

Always let the engine and radiator cool down before removing the radiator cap.

9. Using gloves or a Large heavy

cloth, turn the radiator cap counterclockwise, without pushing down, to the first stop. This releases any remaining pressure in the cooling system. After the pressure releases, push down on the cap and turn it until it comes off.

If Your Engine Overheats

10.Start the engine and set the temperature control lever to maximum. Add coolant to the radiator up to the base of the filler neck. If you do not have the proper coolant mixture available, you can add plain water. Remember to have the cooling system drained and refilled with the proper mixture as soon as you can.

11.Put the radiator cap back on tightly. Run the engine and watch the temperature gauge. If it goes back to the red mark, the engine needs repair. (See Towing on page 164 .)

12.1f the temperature stays normal,

check the coolant level in the radiator reserve tank. If it has gone down, add coolant to the MAX mark. Put the cap back on tightly.

Taking Care of the Unexpected

4. Start the engine and watch the

oil pressure light. If the light does not go out within ten seconds, turn off the engine. There is a mechanical problem that needs to be repaired before you can continue driving. (See Towing on page 164.)

1. Safely pull off the road and shut

off the engine.

2. Let the car sit for a minute. Open

the hood and check the oil level (see page 101). Although oil level and oil pressure are not directly connected, an engine that is very low on oil can loose pressure during cornering and other driving maneuvers.

3. If necessary, add oil to bring the level back to the full mark on the dipstick (see page 101).

Low Oil Pressure

LOW OIL PRESSURE LIGHT

The low oil pressure light should never come on when the engine is running. If this light comes on with the engine running, take immediate action.

NOTICE

Running the engine with low oil pressure can cause serious mechani- cal damage almost immediately. Turn off the engine as soon as you can safely get the car stopped.

Taking Care of the Unexpected

Charging System Indication

Immediately turn off all electrical accessories: radio, heater, A/C, rear defogger, cruise control, etc. Try not to use other electrically- operated controls such as the power windows. Keep the engine running and take extra care not to stall it. Starting the engine will discharge the battery rapidly.

By eliminating as much of the electrical load as possible, you can drive several miles before the battery is too discharged to keep the engine running. Drive to a service station or garage where you can get technical assistance.

CHARGING SYSTEM LIGHT

The charging system light should go out after the engine starts. If it comes on brightly with the engine running, the alternator is no longer charging the battery.

Taking Care of the Unexpected

Malfunction Indicator Lamp/Check Engine Light

NOTICE

If you keep driving with the malfunction indicator lamp/check engine light on, you can damage your car's emission controls and engine. Those repairs may not be covered by your car's warranties.

If this indicator light comes on, safely pull off the road and turn off the engine. Restart the engine and watch the indicator light. If it stays on, have your car checked by the dealer as soon as possible. Drive moderately until the dealer has inspected the problem. Avoid full- throttle acceleration and driving at high speed.

You should also have the dealer inspect your car if the indicator light comes on frequently, even though it goes off when you follow the above procedure.

MALFUNCTION INDICATOR LAMP/ CHECK ENGINE LIGHT

If this indicator light comes on while driving, there is a problem with your engine or its emission control systems. Even though you, may feel no difference in your car's performance, it can reduce your fuel economy and cause your car to put out excessive emissions. Continued operation may cause serious engine damage.

Taking Care of the Unexpected

All the electrical circuits in your car have fuses to protect them from a short circuit or overload. These fuses are located in two fuse boxes.

UNDER- HOOD

TAB

INTERIOR

Fuses

The underhood fuse box is located in the engine compartment next to the battery. To open, push the tab as shown.

The interior fuse box is underneath the dashboard on the driver's side. Remove the fuse box lid by swing- ing the lid down and pulling it straight out of its hinges.

Taking Care of the Unexpected

Fuses

Checking and Replacing Fuses If something electrical in your car stops working, the first thing you should check for is a blown fuse. Determine from the chart on the fuse box cover or inside the fuse box which fuse or fuses control that component. Check those fuses first, but check all the fuses before deciding that is not the cause. Replace any blown fuses and check the component's operation.

1. Turn the ignition switch to

LOCK (0). Make sure the head- lights and all other accessories are off.

2. Remove the cover from the fuse

box.

Taking Care of the Unexpected

FUSE PULLER

BLOWN

3. Check each of the large fuses in

the underhood fuse box by looking through the top at the wire inside. Removing these fuses requires a Phillips-head screwdriver.

4. Check the smaller fuses in the underhood fuse box and all the fuses in the interior fuse box by pulling out each fuse with the fuse puller provided in the interior fuse box.

BLOWN

If you replace the burned out fuse with a spare fuse that has a lower rating, it might blow out again. This does not indicate anything wrong. Replace the fuse with one of the correct rating as soon as you can.

6. If the replacement fuse of the

same rating burns out in a short time, there is probably a serious electrical problem in your car. Leave the burned out fuse in that circuit and have your car check- ed by a qualified technician.

Fuses

NOTICE

Replacing a fuse with one that has a higher rating greatly increases the chances of damaging the electrical system. If you do not have a replacement fuse with the proper rating for the circuit, install one with a lower rating.

5. Look for a burned wire inside the fuse. If it is burned out, replace it with one of the spare fuses of the same rating or lower.

If you cannot drive the car without fixing the problem, and you do not have a spare fuse, take a fuse of the same rating or a lower rating from one of the other circuits. Make sure you can do without that circuit temporarily (such as the rear window defogger, or radio).

Taking Care of the Unexpected

Towing

If your car needs to be towed, call a professional towing service or, if you belong to one, an organization that provides roadside assistance. Never tow your car behind another car with just a rope or chain. It is very dangerous.

Emergency Towing There are three popular methods of towing a car:

Flat-bed Equipment — The operator loads your car on the back of a truck. This is the best way of transporting your Honda.

Wheel Lift Equipment — The tow truck uses two pivoting arms that go under the tires (front or rear) and lift them off the ground. The other two wheels remain on the ground.

Taking Care of the Unexpected

Sling-type Equipment — The tow truck uses metal cables with hooks on the ends. These hooks go around parts of the frame or suspension and the cables lift that end of the car off the ground. Your car's sus- pension and body can be seriously damaged if this method of towing is attempted.

If your Honda cannot be trans- ported by flat-bed, it should be towed with the front wheels off the ground. If due to damage, your car must be towed with the front wheels on the ground, do the following:

5-speed Manual Transmission

Release the parking brake. Shift the transmission to Neutral.

Automatic Transmission

Release the parking brake. Start the engine. Shift to D4, then to N. Turn off the engine.

NOTICE

Improper towing preparation will damage the transmission. Follow the above procedure exactly. If you cannot shift the transmission or start the engine (automatic trans- mission), your car must be trans- ported on a flat-bed.

It is best to tow the car no far- ther than 80 km (50 miles), and keep the speed below 35 mph (55
km/h).

NOTICE

Trying to lift or tow your car by the bumpers will cause serious damage. The bumpers are not designed to support the car's weight.

The diagrams in this section give you the dimensions and capacities of your Honda, and the locations of the identification numbers. The explanations of several electronic and mechanical systems on your Honda are for the more technically- oriented owner.

Technical Information

Identification Numbers............... 166
Specifications................................ 168
Supplemental Restraint

System........................................ 170
Emission Controls........................ 171
The Clean Air Act.................... 171
Crankcase Emission Control

System.................................... 171

Evaporative Emission Control

System.................................... 171
Exhaust Emission Controls..... 172
PGM-FI System.................... 172
Ignition Timing Control

System................................ 172

Three Way Catalytic

Converter........................... 172
Replacement Parts.................... 172

Three Way Catalytic

Converter................................... 173

Technical Information

Identification Numbers

Your car has several identifying numbers located in various places.

The Vehicle Identification Number (VIN) is the 17-digit number your Honda dealer uses to register your car for warranty purposes. It is also necessary for licensing and insur- ing your car. The easiest place to find the VIN is on a plate fastened to the top of the dashboard. You can see it by looking through the windshield on the driver's side. It is also on the Certification label at- tached to the driver's door jamb, and is stamped on the engine com- partment bulkhead. The VIN is also provided in bar code on the Certification label.

Technical Information

VEHICLE IDENTIFICATION NUMBER

CERTIFICATION LABEL

The Engine Number is stamped into the engine block.

The Transmission Number is on a label on top of the transmission.

Identification Numbers

TRANSMISSION NUMBER

ENGINE NUMBER

Technical Information

Specifications

*1 : S *2 : Si

page 117.

Technical Information

* 1 : Including the coolant in the reserve tank and that remaining in the engine.

(0.11 US gal, 0.09 Imp gal)

Reserve tank capacity: 0.4 * 2 : S * 3 : Si * 4 : Excluding the oil remaining in the engine.

Specifications

*1 : S *2 : Si

Technical Information

Supplemental Restraint System

The electrical charge sent to the airbag assembly ignites its propel- lant, which burns instantaneously. The gas produced by the burning propellant inflates the airbag instantly.

The airbag is vented so it stays inflated for only an instant and does not block the driver's vision. Smoke from the burned propellant comes out of the airbag and into the car's interior. This is normal and does not mean there is a fire. The airbag collapses onto the driver's lap.

The airbag unit can inflate only one time. After use, your Honda dealer must check the complete Supple- mental Restraint System and re- place the airbag assembly.

To ensure long-term reliability, the SRS uses gold-plated electrical connections throughout. Exposed components are sealed with epoxy. The control unit monitors the SRS circuitry whenever the ignition is ON (II). If the control unit senses any faults, it turns on the SRS indicator light on the instrument panel. Take the car to your Honda dealer to diagnose and repair the system as soon as possible.

The SRS needs no regular mainte- nance other than an inspection by