2005 Honda Civic Coupe Owners Manual

3.

Remove the bulb by turning it one- quarter turn counterclockwise.

Lights

4.

5.

Insert the new bulb into the hole and turn it one-quarter turn clock- wise to lock it in place.

Push the electrical connector back onto the bulb. Make sure it is on all the way.

6.

Turn on the headlights to test the new bulb.

7.

(Passenger’s side) Put the battery back to its original position, reinstall the bolt in the stay and tighten it securely.

(Driver’s side) Reinstall the power steering reservoir.

171

Main MenuTable of Contentsst０４／０８／０４　１４：５０：２７　３１Ｓ５Ｐ６４０　０１７５　

Lights

Replacing the Front Side Marker/ Turn Signal and Parking Light Bulb

BULB

SOCKET

4.

Remove the bulb from the socket by pushing it in and turning the bulb counterclockwise until it unlocks.

5.

Install the new bulb in the socket. Turn it clockwise to lock it in place.

6.

7.

Insert the socket back into the headlight assembly. Turn it clockwise to lock it in place.

Put the inner fender cover in place. Install the holding clip. Lock it in place by pushing on the center.

1.

If you are changing the bulb on the driver’s side, start the engine, turn the steering wheel all the way to the right, and turn off the engine. If you are changing the bulb on the passenger’s side, turn the steering wheel to the left.

2.

Use a flat-tipped screwdriver to remove the holding clip from the inner fender, and pull the inner fender cover back.

3.

Remove the socket from the headlight assembly by turning it one-quarter turn counterclockwise.

172

Main MenuTable of Contentsst０４／０８／０４　１４：５０：３７　３１Ｓ５Ｐ６４０　０１７６　

Replacing Rear Bulbs

BULBS

SOCKET

FASTENER

1.

Open the trunk.

Remove the screw in the center of the fastener on the side of the trunk lining. Pull the lining back.

BULB

SOCKETS

2.

Determine which of the three bulbs is burned out: stop/taillight, back-up light or turn signal light.

3.

Remove the socket by turning it one-quarter turn counterclockwise.

Lights

4.

5.

Pull the bulb straight out of its socket. Push the new bulb straight into the socket until it bottoms.

Reinstall the socket into the light assembly by turning it clockwise until it locks.

6.

Turn on the lights to make sure the new bulb is working.

7.

8.

Reinstall the trunk lining. Make sure it is installed under the edge of the trunk seal.

Put the fastener into the hole on the side of the trunk lining. Reinstall the screw.

173

Main MenuTable of Contentsst０４／０８／０４　１４：５０：４６　３１Ｓ５Ｐ６４０　０１７７　

Lights, Cleaning the Seat Belts

Replacing a High-mount Brake Light Bulb

3.

Reinstall the socket. Turn it clockwise until it locks. Make sure the new bulb is working.

Cleaning the Seat Belts

LOOP

BULB

SOCKET

EXceptU.S.SpecialEditionmodelsand CanadianREVERBandSimodels 1.

Open the trunk and remove the socket from the light assembly by turning it one-quarter turn counter- clockwise.

2.

Pull the bulb straight out of its socket. Push the new bulb straight into the socket until it bottoms.

174

If your seat belts get dirty, use a soft brush with a mixture of mild soap and warm water to clean them. Do not use bleach, dye, or cleaning solvents. Let the belts air-dry before you use the vehicle.

Main MenuTable of Contentsst０４／０８／０４　１４：５０：５４　３１Ｓ５Ｐ６４０　０１７８　

Dirt build-up in the loops of the seat belt anchors can cause the belts to retract slowly. Wipe the insides of the loops with a clean cloth dampened in mild soap and warm water or isopropyl alcohol.

Floor Mats

Cleaning the Seat Belts, Floor Mats

If you use a non-Honda floor mat, make sure it fits properly and that it can be used with the floor mat anchor. Do not put additional floor mats on top of the anchored mat.

Ifequipped The driver’s floor mat that came with your vehicle hooks over the floor mat anchors. This keeps the floor mat from sliding forward and possibly interfering with the pedals.

If you remove the driver’s floor mat, make sure to re-anchor it when you put it back in your vehicle.

175

Main MenuTable of Contentsst０４／０８／０４　１４：５１：０４　３１Ｓ５Ｐ６４０　０１７９　

Dust and Pollen Filter, Wiper Blades

Dust and Pollen Filter IfequippedwithA/C This filter removes the dust and pollen that is brought in from the outside through the heating and cooling system.

Have your dealer replace this filter every 30,000 miles (48,000 km) under normal conditions. It should be replaced every 15,000 miles (24,000 km) if you drive primarily in urban areas that have high concentrations of soot in the air, or if the flow from the heating and cooling system becomes less than usual.

Wiper Blades Check the condition of the wiper blades at least every six months. Replace them if you find signs of cracking in the rubber, areas that are getting hard, or if they leave streaks and unwiped areas when used.

1.

Raise the wiper arm off the windshield.

Do not open the hood when the wiper arms are raised, or you will damage the hood and wiper arms.

LOCK TAB

2.

Disconnect the blade assembly from the wiper arm by pushing in the lock tab. Hold the lock tab in while you push the blade assembly toward the base of the arm.

176

Main MenuTable of Contentsst０４／０８／０４　１４：５１：１３　３１Ｓ５Ｐ６４０　０１８０　

Wiper Blades

BLADE

5.

Slide the new wiper blade into the holder until the tabs lock.

6.

Slide the wiper blade assembly onto the wiper arm. Make sure it locks in place.

7.

Lower the wiper arm down against the windshield.

BLADE

REINFORCEMENT

3.

Remove the blade from its holder by grasping the tabbed end of the blade. Pull firmly until the tabs come out of the holder.

4.

Examine the new wiper blades. If they have no plastic or metal reinforcement along the back edge, remove the metal reinforcement strips from the old wiper blade, and install them in the slots along the edge of the new blade.

177

Main MenuTable of Contentsst０４／０８／０４　１４：５１：２３　３１Ｓ５Ｐ６４０　０１８１　

Tires

To safely operate your vehicle, your tires must be the proper type and size, in good condition with adequate tread, and correctly inflated.

The following pages give more detailed information on how to take care of your tires and what to do when they need to be replaced.

Using tires that are excessively worn or improperly inflated can cause a crash in which you can be seriously hurt or killed.

Follow all instructions in this owner’s manual regarding tire inflation and maintenance.

Inflation Guidelines Keeping the tires properly inflated provides the best combination of handling, tread life, and riding comfort.

Underinflated tires wear unevenly, adversely affect handling and fuel economy, and are more likely to fail from being overheated.

Overinflated tires can make your vehicle ride more harshly, are more prone to damage from road hazards, and wear unevenly.

We recommend that you visually check your tires every day. If you think a tire might be low, check it immediately with a tire gauge.

178

Use a gauge to measure the air pressure in each tire at least once a month. Even tires that are in good condition may lose one to two psi (10
to 20 kPa, 0.1 to 0.2 kgf/cm ) per month. Remember to check the spare tire at the same time.

Check the air pressures when the tires are cold. This means the vehicle has been parked for at least three hours, or driven less than 1
mile (1.6 km). Add or release air, if needed, to match the recommended cold tire pressures on page

179

Main MenuTable of Contentsst０４／０８／０４　１４：５１：４０　３１Ｓ５Ｐ６４０　０１８２　

If you check air pressures when the tires are hot [driven for several miles (kilometers)], you will see readings 4
to 6 psi (30 to 40 kPa, 0.3 to 0.4
kgf/cm ) higher than the cold readings. This is normal. Do not let air out to match the recommended cold air pressure. The tire will be underinflated.

You should use your own tire pressure gauge whenever you check your tire pressures. This will make it easier for you to tell if a pressure loss is due to a tire problem and not due to a variation between gauges.

While tubeless tires have some ability to self-seal if they are punctured, you should look closely for punctures if a tire starts losing pressure.

Recommended Tire Pressures NormalDriving The following charts show the recommended cold tire pressures for most normal driving conditions and speeds.

U.S.: DX, Value Package, HX, Canada: DX

Tire Size

P185/70R14 87S

Cold Tire Pressure for Normal Driving 30 psi (210 kPa , 2.1
kgf/cm )

Canada: LX

Tire Size

P185/65R15 86H

Cold Tire Pressure for Normal Driving 30 psi (210 kPa , 2.1
kgf/cm )

U.S.: LX, EX, Special Edition, Canada: Si, REVERB

Tire Size

P195/60R15 87H

Cold Tire Pressure for Normal Driving 30 psi (210 kPa , 2.1
kgf/cm )

Tires

The compact spare tire pressure is: 60 psi (420 kPa , 4.2 kgf/cm )

High-SpeedDriving U.S.DX,ValuePackage,HXand CanadianDXmodelsonly Honda strongly recommends that you not drive faster than posted speed limits and conditions allow. If you decide it is safe to drive at high speeds (over 100 mph or 160 km/h), be sure to adjust the cold tire pressures as shown below. If you do not, excessive heat can build up and cause sudden tire failure.

U.S.: DX, Value Package, HX, Canada: DX

Tire Size

P185/70R14 87S

Cold Tire Pressure for High-Speed Driving 35 psi (240 kPa , 2.4
kgf/cm )

CONTINUED

179

Main MenuTable of Contentsst０４／０８／０４　１４：５１：５１　３１Ｓ５Ｐ６４０　０１８３　

Tires

U.S.LX,EX,SpecialEditionand CanadianREVERB,LX,Simodels Tire pressure for high-speed driving is the same as for normal driving.

Tire Inspection Every time you check inflation, you should also examine the tires for damage, foreign objects, and wear.

INDICATOR LOCATION MARKS

When you return to normal speed driving, be sure to readjust the tire pressure for normal driving. You should wait until the tires are cold before adjusting the tire pressure.

For convenience, the recommended tire sizes and cold air pressures are on a label on the driver’s doorjamb.

For additional information about your tires, see page

216

You should look for:

Bumps or bulges in the tread or side of the tire. Replace the tire if you find either of these conditions.

Cuts, splits, or cracks in the side of the tire. Replace the tire if you can see fabric or cord.

Excessive tread wear.

TREAD WEAR INDICATOR

Your tires have wear indicators molded into the tread. When the tread wears down, you will see a band 1/2 inch (12.7 mm) wide across the tread. This shows there is less than 1/16 inch (1.6 mm) of tread left on the tire.

A tire this worn gives very little traction on wet roads. You should replace the tire if you can see three or more tread wear indicators.

180

Main MenuTable of Contentsst０４／０８／０４　１４：５２：０３　３１Ｓ５Ｐ６４０　０１８４　

Tire Maintenance In addition to proper inflation, correct wheel alignment helps to decrease tire wear. If you find a tire is worn unevenly, have your dealer check the wheel alignment.

Have your dealer check the tires if you feel a consistent vibration while driving. A tire should always be rebalanced if it is removed from the wheel. When you have new tires installed, make sure they are balanced. This increases riding comfort and tire life. For best results, have the installer perform a dynamic balance.

Forvehiclesequippedwithaluminum wheels: Improper wheel weights can damage your vehicle’s aluminum wheels. Use only Honda wheel weights f or balancing.

Tire Rotation

Front

Front

(Front Non-directional Tires and Wheels)

(Front Directional Tires and Wheels)

To help increase tire life and distribute wear more evenly, rotate the tires every 10,000 miles (16,000
km). Move the tires to the positions shown in the chart each time they are rotated. If you purchase directional tires, rotate only front-to- back.

Tires

Replacing Tires and Wheels Replace your tires with radial tires of the same size, load range, speed rating, and maximum cold tire pressure rating (as shown on the tire’s sidewall).

Mixing radial and bias-ply tires on your vehicle can reduce braking ability, traction, and steering accuracy. Using tires of a different size or construction can cause the ABS to work inconsistently.

It is best to replace all four tires at the same time. If that is not possible or necessary, replace the two front tires or two rear tires as a pair. Replacing just one tire can seriously affect your vehicle’s handling.

CONTINUED

181

Main MenuTable of Contentsst０４／０８／０４　１４：５２：１８　３１Ｓ５Ｐ６４０　０１８５　

Tires

The ABS works by comparing the speed of the wheels. When replacing tires, use the same size originally supplied with the vehicle. Tire size and construction can affect wheel speed and may cause the system to work.

If you ever replace a wheel, make sure the new one matches the specifications of the original. Replacement wheels are available at your dealer.

Installing improper tires on your vehicle can affect handling and stability. This can cause a crash in which you can be seriously hurt or killed.

Always use the size and type of tires recommended in this owner’s manual.

182

Wheel and Tire Specifications Wheels:

U.S.: DX, Value Package, HX Canada: DX

14 x 5 1/2 JJ

U.S.: LX, EX, Special Edition Canada: LX, REVERB, Si

15 x 6 JJ

Tires:

U.S.: DX,Value Package, HX Canada: DX

P185/70R14 87S

Canada: LX

P185/65R15 86H

U.S.: LX, EX, Special Edition Canada: Si, REVERB P195/60R15 87H

216

for information about

See page DOT Tire Quality Grading, and page 218
information.

for tire size and labeling

Winter Driving Tires marked ‘‘M S’’ or ‘‘All Season’’ on the sidewall have an all- weather tread design suitable for most winter driving conditions.

＋

For the best performance in snowy or icy conditions, you should install snow tires or tire chains. They may be required by local laws under certain conditions.

SnowTires If you mount snow tires on your vehicle, make sure they are radial tires of the same size and load range as original tires. Mount snow tires on all four wheels. The traction provided by snow tires on dry roads may be lower than your original tires. Check with the tire dealer for maximum speed recommendations.

Main MenuTable of Contentsst０４／０８／０４　１４：５２：２４　３１Ｓ５Ｐ６４０　０１８６　

Traction devices that are the wrong size or improperly installed can damage your vehicle’s brake lines, suspension, body, and wheels. Stop driving if they are hitting any part of the vehicle.

TireChains Because your vehicle has limited tire clearance, mount only SAE Class ‘‘S’’ cable-type traction devices, with rubber chain tensioners, on the front tires. Use traction devices only when required by driving conditions or local laws. Make sure they are the correct size for your tires. Metal link- type ‘‘chains’’ should not be used.

When installing cables, follow the manufacturer’s instructions, and mount them as tight as you can. Make sure they are not contacting the brake lines or suspension. Drive slowly with them installed. If you hear them coming into contact with the body or chassis, stop and investigate. Remove them as soon as you begin driving on cleared roads.

Tires

183

Main MenuTable of Contentsst０４／０８／０４　１４：５２：３２　３１Ｓ５Ｐ６４０　０１８７　

Checking the Battery

TEST INDICATOR WINDOW

Check the condition of the battery monthly by looking at the test indicator window. The label on the battery explains the test indicator’s colors.

184

Check the terminals for corrosion (a white or yellowish powder). To remove it, cover the terminals with a solution of baking soda and water. It will bubble up and turn brown. When this stops, wash it off with plain water. Dry off the battery with a cloth or paper towel. Coat the terminals with grease to help prevent further corrosion.

If additional battery maintenance is needed, see your dealer or a qualified technician.

Battery posts,

WARNING: terminals, and related accessories contain lead and lead compounds. Wash your hands after handling.

If you need to connect the battery to a charger, disconnect both cables to prevent damaging your vehicle’s electrical system. Always disconnect the negative ( − reconnect it last.

) cable first, and

The battery gives off explosive hydrogen gas during normal operation.

A spark or flame can cause the battery to explode with enough force to kill or seriously hurt you.

Wear protective clothing and a face shield, or have a skilled mechanic do the battery maintenance.

Main MenuTable of Contentsst０４／０８／０４　１４：５２：４４　３１Ｓ５Ｐ６４０　０１８８　

If you need to park your vehicle for an extended period (more than one month), there are several things you should do to prepare it for storage. Proper preparation helps prevent deterioration and makes it easier to get your vehicle back on the road. If possible, store your vehicle indoors.

Fill the fuel tank.

Block the rear wheels.

If the vehicle is to be stored for a longer period, it should be supported on jackstands so the tires are off the ground.

Leave one window open slightly (if the vehicle is being stored indoors).

Change the engine oil and filter.

Disconnect the battery.

Wash and dry the exterior completely.

Clean the interior. Make sure the carpeting, floor mats, etc., are completely dry.

Leave the parking brake off. Put the transmission in Reverse (manual) or Park (automatic).

Support the front wiper blade arms with a folded towel or rag so they do not touch the windshield.

To minimize sticking, apply a silicone spray lubricant to all door and trunk seals. Also, apply a vehicle body wax to the painted surfaces that mate with the door and trunk seals.

Vehicle Storage

Cover the vehicle with a ‘‘breathable’’ cover, one made from a porous material such as cotton. Non-porous materials, such as plastic sheeting, trap moisture, which can damage the paint.

If possible, periodically run the engine until it reaches full operating temperature (the cooling fans cycle on and off twice). Preferably, do this once a month.

If you store your vehicle for 1 year or longer, have your dealer perform the inspections called for in the 2 years/ 30,000 miles (48,000 km) maintenance schedule (Normal Conditions) as soon as you take it out of storage (see page ). The replacements called for in the maintenance schedule are not needed unless the vehicle has actually reached that time or mileage.

153

185

Main MenuTable of Contentsst０４／０８／０４　１４：５２：５１　３１Ｓ５Ｐ６４０　０１９０　

Taking Care of the Unexpected

This section covers the more common problems that motorists experience with their vehicles. It gives you information about how to safely evaluate the problem and what to do to correct it. If the problem has stranded you on the side of the road, you may be able to get going again. If not, you will also find instructions on getting your vehicle towed.

Compact Spare Tire Changing a Flat Tire If the Engine Won’t Start Jump Starting If the Engine Overheats Low Oil Pressure Indicator Charging System Indicator Malfunction Indicator Lamp Brake System Indicator Closing the Moonroof Fuses Fuse Locations Emergency Towing

...................... .................... ............. ................................ .............. ......... .......... ....... ............... .................. .............................................. .............................. ......................

. 188
. 189
. 194
. 196
. 197
. 200
. 200
. 201
. 202
. 203
. 204
. 207
. 209

187

Main Menust０４／０８／０４　１４：５３：００　３１Ｓ５Ｐ６４０　０１９１　

Compact Spare Tire

Use the compact spare tire as a temporary replacement only. Get your regular tire repaired or replaced, and put it back on your vehicle as soon as you can.

Check the inflation pressure of the compact spare tire every time you check the other tires. It should be inflated to:

60 psi (420 kPa , 4.2 kgf/cm )

188

Follow these precautions:

INDICATOR LOCATION MARK

Never exceed 50 mph (80 km/h).

This tire gives a harsher ride and less traction on some road sur- faces. Use greater caution while driving.

Do not mount snow chains on the compact spare tire.

Do not use your compact spare tire on another vehicle unless it is the same make and model.

TREAD WEAR INDICATOR

Replace the tire when you can see the tread wear indicator bars. The replacement should be the same size and design tire, mounted on the same wheel. The spare tire is not designed to be mounted on a regular wheel, and the spare wheel is not designed for mounting a regular tire.

Main MenuTable of Contentsst０４／０８／０４　１４：５３：０９　３１Ｓ５Ｐ６４０　０１９２　

If you have a flat tire while driving, stop in a safe place to change it. Drive slowly along the shoulder until you get to an exit or an area that is far away from the traffic lanes.

The vehicle can easily roll off the jack, seriously injuring anyone underneath.

Follow the directions for changing a tire exactly, and never get under the vehicle when it is supported only by the jack.

1.

2.

Park the vehicle on firm, level and non-slippery ground. Put the transmission in Park (automatic) or Reverse (manual). Apply the parking brake.

Turn on the hazard warning lights, and turn the ignition switch to LOCK (0). Have all the passengers get out of the vehicle while you change the tire.

Changing a Flat Tire

SPARE TIRE

TRUNK FLOOR

TOOL KIT

JACK

3.

Open the trunk. Raise the trunk floor mat and the trunk floor by lifting up on the back edge.

4.

Take the tool kit out of the trunk.

5.

Unscrew the wing bolt and take the spare tire out of its well.

CONTINUED

189

Main MenuTable of Contentsst０４／０８／０４　１４：５３：１６　３１Ｓ５Ｐ６４０　０１９３　

Changing a Flat Tire

JACK

JACKING POINTS

6.

Turn the jack’s end counterclockwise to loosen it, then remove the jack.

WHEEL NUT WRENCH

7.

Loosen each wheel nut 1/2 turn with the wheel nut wrench.

8.

Place the jack under the jacking point nearest the tire you need to change. Turn the end bracket clockwise until the top of the jack contacts the jacking point. Make sure the jacking point tab is resting in the jack notch.

190

Main MenuTable of Contentsst０４／０８／０４　１４：５３：２７　３１Ｓ５Ｐ６４０　０１９４　

Changing a Flat Tire

WHEEL NUTS

WHEEL NUTS WHEEL COVER

BRAKE HUB

DX,ValuePackage,andLXmodels Do not attempt to forcibly pry the wheel cover off with a screwdriver or other tool. The wheel cover cannot be removed without first removing the wheel nuts.

11.

Before mounting the spare tire, wipe any dirt off the mounting surface of the wheel and hub with a clean cloth. Wipe the hub carefully; it may be hot from driving.

EXTENSION WHEEL NUT WRENCH Use the extension and the wheel 9. nut wrench as shown to raise the vehicle until the flat tire is off the ground.

10.

Remove the wheel nuts, then remove the flat tire. Handle the wheel nuts carefully; they may be hot from driving. Place the flat tire on the ground with the outside surface facing up.

CONTINUED

191

Main MenuTable of Contentsst０４／０８／０４　１４：５３：３５　３１Ｓ５Ｐ６４０　０１９５　

Changing a Flat Tire

12.

Put on the spare tire. Put the wheel nuts back on finger-tight, then tighten them in a crisscross pattern with the wheel nut wrench until the wheel is firmly against the hub. Do not try to tighten them fully.

13.

Lower the vehicle to the ground and remove the jack.

14.

Tighten the wheel nuts securely in the same crisscross pattern. Have the wheel nut torque checked at the nearest automotive service facility.

15.OnHX,SpecialEdition,andEX

modelsintheU.S.,REVERBandSi modelsinCanada Remove the center cap from the flat tire.

Tighten the wheel nuts to: 80 lbf·ft (108 N·m , 11 kgf·m)

192

Main MenuTable of Contentsst０４／０８／０４　１４：５３：４４　３１Ｓ５Ｐ６４０　０１９６　

Changing a Flat Tire

WING BOLT

SPACER CONE

19.

Store the jack in the trunk with the end bracket on the left side. Turn the jack’s end bracket to lock it in place. Store the tool kit.

Loose items can fly around the interior in a crash and could seriously injure the occupants.

Store the wheel, jack, and tools securely before driving.

20.

Store the wheel cover or center cap in the trunk. Make sure it does not get scratched or damaged.

21.

Lower the trunk floor, then close the trunk lid.

16.

Place the flat tire face down in the spare tire well.

17.

Remove the spacer cone from the wing bolt, turn it over, and put it back on the bolt.

18.

Secure the flat tire by screwing the wing bolt back into its hole.

193

Main MenuTable of Contentsst０４／０８／０４　１４：５３：５４　３１Ｓ５Ｐ６４０　０１９７　

If the Engine Won’t Start

Diagnosing why the engine won’t start falls into two areas, depending on what you hear when you turn the key to START (III):

You hear nothing, or almost nothing. The engine’s starter motor does not operate at all, or operates very slowly.

You can hear the starter motor operating normally, or the starter motor sounds like it is spinning faster than normal, but the engine does not start up and run.

Nothing Happens or the Starter Motor Operates Very Slowly When you turn the ignition switch to START (III), you do not hear the normal noise of the engine trying to start. You may hear a clicking sound or series of clicks, or nothing at all. Check these things:

Check the transmission interlock. If you have a manual transmission, the clutch pedal must be pushed all the way to the floor or the starter will not operate. With an automatic transmission, it must be in Park or Neutral.

Turn the ignition switch to ON (II). Turn on the headlights, and check their brightness. If the headlights are very dim or do not come on at all, the battery is discharged. See Jump Starting

on page

196

194

Turn the ignition switch to START (III). If the headlights do not dim, check the condition of the fuses. If the fuses are OK, there is probably something wrong with the electrical circuit for the ignition switch or starter motor. You will need a qualified technician to determine the Emergency Towing problem (see ). on page 209

If the headlights dim noticeably or go out when you try to start the engine, either the battery is dis- charged or the connections are corroded. Check the condition of the battery and terminal connec- tions (see page then try jump starting the vehicle from a booster battery (see page 196

). You can

184

).

Main MenuTable of Contentsst０４／０８／０４　１４：５４：０２　３１Ｓ５Ｐ６４０　０１９８　

The Starter Operates Normally In this case, the starter motor’s speed sounds normal, or even faster than normal, when you turn the ignition switch to START (III), but the engine does not run.

Are you using a properly coded key? An improperly coded key will cause the immobilizer system indicator in the instrument panel ). to blink rapidly (see page

67

Are you using the proper starting Starting the procedure? Refer to Engine 135

on page

If the Engine Won’t Start

Do you have fuel? Check the fuel gauge; the low fuel indicator may not be working.

There may be an electrical problem, such as no power to the fuel pump. Check all the fuses (see page

204

).

If you find nothing wrong, you will need a qualified technician to find the problem. See Towing on page

Emergency 209

195

Main MenuTable of Contentsst０４／０８／０４　１４：５４：１２　３１Ｓ５Ｐ６４０　０１９９　

Jump Starting

Although this seems like a simple procedure, you should take several precautions.

A battery can explode if you do not follow the correct procedure, seriously injuring anyone nearby.

Keep all sparks, open flames, and smoking materials away from the battery.

You cannot start your vehicle with an automatic transmission by pushing or pulling it.

ToJumpStartYourVehicle: 1.

Open the hood, and check the physical condition of the battery. In very cold weather, check the condition of the electrolyte. If it seems slushy or frozen, do not try jump starting until it thaws.

If a battery sits in extreme cold, the electrolyte inside can f reeze. Attempting to jump start with a f rozen battery can cause it to rupture.

2.

Turn off all the electrical acces- sories: heater, A/C, stereo system, lights, etc. Put the transmission in Neutral or Park, and set the parking brake.

196

BOOSTER BATTERY

The numbers in the illustration show you the order to connect the jumper cables.

3.

＋

) terminal on your

Connect one jumper cable to the positive ( battery. Connect the other end to the positive ( ) terminal on the ＋ booster battery.

Main MenuTable of Contentsst０４／０８／０４　１４：５４：２４　３１Ｓ５Ｐ６４０　０２００　

Jump Starting, If the Engine Overheats

6.

7.

Start your vehicle. If the starter motor still operates slowly, check that the jumper cables have good metal-to-metal contact.

Once your vehicle is running, disconnect the negative cable from your vehicle, then from the booster battery. Disconnect the positive cable from your vehicle, then from the booster battery.

Keep the ends of the jumper cables away from each other and any metal on the vehicle until everything is disconnected. Otherwise, you may cause an electrical short.

If the Engine Overheats The pointer of the vehicle’s temperature gauge should stay in the midrange. If it climbs to the red mark, you should determine the reason (hot day, driving up a steep hill, etc.).

If the vehicle overheats, you should take immediate action. The only indication may be the temperature gauge climbing to or above the red mark. Or you may see steam or spray coming from under the hood.

Driving with the temperature gauge pointer at the red mark can cause serious damage to your engine.

CONTINUED

197

4.

−

Connect the second jumper cable to the negative ( ) terminal on the booster battery. Connect the other end to the grounding strap as shown. Do not connect this jumper cable to any other part of the engine.

5.

If the booster battery is in another vehicle, have an assistant start that vehicle and run it at a fast idle.

Main MenuTable of Contentsst０４／０８／０４　１４：５４：３２　３１Ｓ５Ｐ６４０　０２０１　

3.

If you do not see steam or spray, leave the engine running, and watch the temperature gauge. If the high heat is due to overloading, the engine should start to cool down almost immediately. If it does, wait until the temperature gauge comes down to the midpoint, then continue driving.

4.

If the temperature gauge stays at the red mark, turn off the engine.

5.

Look for any obvious coolant leaks, such as a split radiator hose. Everything is still extremely hot, so use caution. If you find a leak, it must be repaired before you Emergency continue driving (see Towing ). 209

on page

6.

If you don’t find an obvious leak, check the coolant level in the radiator reserve tank (see page ). Add coolant if the level is 126
below the MIN mark.

If the Engine Overheats

Steam and spray from an overheated engine can seriously scald you.

Do not open the hood if steam is coming out.

1.

2.

Safely pull to the side of the road. Put the transmission in Neutral or Park, and set the parking brake. Turn off all accessories, and turn on the hazard warning indicators.

If you see steam and/or spray coming from under the hood, turn off the engine. Wait until you see no more signs of steam or spray, then open the hood.

198

Main MenuTable of Contentsst０４／０８／０４　１４：５４：４０　３１Ｓ５Ｐ６４０　０２０２　

If the Engine Overheats

7.

If there was no coolant in the reserve tank, you may need to add coolant to the radiator. Let the engine cool down until the pointer reaches the middle of the temperature gauge or lower before checking the radiator.

Removing the radiator cap while the engine is hot can cause the coolant to spray out, seriously scalding you.

Always let the engine and radiator cool down before removing the radiator cap.

8.

9.

Using gloves or a large heavy cloth, turn the radiator cap counterclockwise, without pushing down, to the first stop. After the pressure releases, push down on the cap, and turn it until it comes off.

Start the engine, and set the temperature control dial to maximum heat. Add coolant to the radiator up to the base of the filler neck. If you do not have the proper coolant mixture available, you can add plain water. Remember to have the cooling system drained and refilled with the proper mixture as soon as you can.

10.

Put the radiator cap back on tightly. Run the engine, and watch the temperature gauge. If it goes back to the red mark, the engine needs repair (see Towing on page

Emergency 209

).

11.

If the temperature stays normal, check the coolant level in the radiator reserve tank. If it has gone down, add coolant to the MAX mark. Put the cap back on tightly.

199

Main MenuTable of Contentsst０４／０８／０４　１４：５４：５２　３１Ｓ５Ｐ６４０　０２０３　

Low Oil Pressure Indicator, Charging System Indicator

Low Oil Pressure Indicator

This indicator should never come on when the engine is running. If it starts flashing or stays on, the oil pressure has dropped very low or lost pressure. Serious engine damage is possible and you should take immediate action.

Running the engine with low oil pressure can cause serious mechanical damage almost immediately. Turn of f the engine as soon as you can saf ely get the vehicle stopped.

1.

2.

3.

4.

200

Safely pull off the road, and shut off the engine. Turn on the hazard warning indicators.

Let the vehicle sit for a minute. Open the hood, and check the oil level (see page ). An engine very low on oil can lose pressure during cornering and other driving maneuvers.

125

If necessary, add oil to bring the level back to the full mark on the dipstick (see page

159

).

Start the engine, and watch the oil pressure indicator. If it does not go out within 10 seconds, turn off the engine. There is a mechanical problem that needs to be repaired before you can continue driving (see 209

Emergency Towing ).

on page

Charging System Indicator

If the charging system indicator comes on brightly

when the engine is running, the battery is not being charged.

Immediately turn off all electrical accessories. Try not to use other electrically operated controls such as the power windows. Keep the engine running; starting the engine will discharge the battery rapidly.

Go to a service station or garage where you can get technical assistance.

Main MenuTable of Contentsst０４／０８／０４　１４：５５：０１　３１Ｓ５Ｐ６４０　０２０４　

If the indicator comes on while driving, it means one

of the engine’s emissions control systems may have a problem. Even though you may feel no difference in your vehicle’s performance, it can reduce your fuel economy and cause increased emissions. Continued operation may cause serious damage.

If you have recently refueled your vehicle, the indicator coming on could be due to a loose or missing fuel fill cap. Tighten the cap until it clicks at least three times. Tightening the cap will not turn the indicator off immediately; it takes at least three days of normal driving.

Malfunction Indicator Lamp

If the indicator comes on repeatedly, even though it may turn off as you continue driving, have the vehicle checked by your dealer as soon as possible.

If your vehicle battery has been disconnected or gone dead, these codes are erased. It takes at least three days of driving under various conditions to set the codes again.

To check if they are set, turn the ignition switch to ON (II), without starting the engine. The Malfunction Indicator Lamp will come on for 20
seconds. If it then goes off, the readiness codes are set. If it blinks 5
times, the readiness codes are not set. If possible, do not take your vehicle for a state emissions test until the readiness codes are set. Refer to State Emissions Testing for more information (see page

222

).

If you keep driving with the Malf unction Indicator Lamp on, you can damage your vehicle’s emissions controls and the engine. Those repairs may not be covered by your vehicle’s warranties.

Readiness Codes Your vehicle has certain ‘‘readiness codes’’ that are part of the on-board diagnostics for the emissions systems. In some states, part of the emissions testing is to make sure these codes are set. If they are not set, the test cannot be completed.

201

Main MenuTable of Contentsst０４／０８／０４　１４：５５：１０　３１Ｓ５Ｐ６４０　０２０５　

Brake System Indicator

However, if the brake pedal does not feel normal, you should take immediate action. A problem in one part of the system’s dual circuit design will still give you braking at two wheels. You will feel the brake pedal go down much farther before the vehicle begins to slow down, and you will have to press harder on the pedal.

OnmodelsequippedwithABS If the ABS indicator comes on with the brake system indicator, have your vehicle inspected by your dealer immediately.

Slow down by shifting to a lower gear, and pull to the side of the road when it is safe. Because of the long distance needed to stop, it is hazardous to drive the vehicle. You should have it towed and repaired as soon as possible (see Towing 209

Emergency ).

on page

If you must drive the vehicle a short distance in this condition, drive slowly and carefully.

U.S.

Canada

The brake system indicator normally comes on when you turn the ignition switch to ON (II), and as a reminder to check the parking brake. It will stay on if you do not fully release the parking brake.

If the brake system indicator comes on while driving, the brake fluid level is probably low. Press lightly on the brake pedal to see if it feels normal. If it does, check the brake fluid level the next time you stop at a service station (see page

168

).

If the fluid level is low, take your vehicle to a dealer, and have the brake system inspected for leaks or worn brake pads.

202

Main MenuTable of Contentsst０４／０８／０４　１４：５５：２１　３１Ｓ５Ｐ６４０　０２０６　

Ifequipped If the electric motor will not close the moonroof, do the following:

1.

2.

Check the fuse for the moonroof motor (see page ). If the fuse is blown, replace it with one of the same or lower rating.

208

Try closing the moonroof. If the new fuse blows immediately or the moonroof motor still does not operate, you can close the moonroof manually.

3.

Get the moonroof wrench out of the tool kit in the trunk.

ROUND PLUG

4.

Use a screwdriver or coin to remove the round plug in the center of the headliner.

Closing the Moonroof

SOCKET

MOONROOF WRENCH

5.

Insert the moonroof wrench into the socket behind the plug. Turn the wrench until the moonroof is fully closed.

6.

Remove the wrench. Reinstall the round plug.

If you need to close the moonroof manually, it means the moonroof opening/closing function is developing a problem. Have your vehicle checked by your dealer.

203

Main MenuTable of Contentsst０４／０８／０４　１４：５５：３１　３１Ｓ５Ｐ６４０　０２０７　

Fuses

INTERIOR

UNDER-HOOD

TAB

207

and

Checking and Replacing Fuses If something electrical in your vehicle stops working, check for a blown fuse first. Determine from the chart on pages , or the diagram on the fuse box lid, which fuse or fuses control that device. Check those fuses first, but check all the fuses before deciding that a blown fuse is the cause. Replace any blown fuses, and check if the device works.

208

The vehicle’s fuses are contained in two fuse boxes.

The interior fuse box is underneath the steering column. To open it, turn the knobs as shown.

The under-hood fuse box is in the engine compartment on the passenger’s side next to the battery. To open it, push the tabs as shown.

1.

Turn the ignition switch to LOCK (0). Make sure the headlights and all other accessories are off.

2.

Remove the cover from the fuse box.

204

Main MenuTable of Contentsst０４／０８／０４　１４：５５：４０　３１Ｓ５Ｐ６４０　０２０８　

FUSE

BLOWN

Fuses

BLOWN

FUSE PULLER

3.

Check each of the large fuses in the under-hood fuse box by looking through the top at the wire inside. Removing these fuses requires a Phillips-head screw- driver.

4.

Check the smaller fuses in the under-hood fuse box and all the fuses in the interior fuse box by pulling out each one with the fuse puller provided in the under-hood fuse box.

5.

Look for a burned wire inside the fuse. If it is burned, replace it with one of the spare fuses of the same rating or lower.

CONTINUED

205

Main MenuTable of Contentsst０４／０８／０４　１４：５５：４８　３１Ｓ５Ｐ６４０　０２０９　

Fuses

If you cannot drive the vehicle without fixing the problem, and you do not have a spare fuse, take a fuse of the same rating or a lower rating from one of the other circuits. Make sure you can do without that circuit temporarily (such as the accessory power socket or radio).

If you replace the blown fuse with a spare fuse that has a lower rating, it might blow out again. This does not indicate anything wrong. Replace the fuse with one of the correct rating as soon as you can.

Replacing a f use with one that has a higher rating greatly increases the chances of damaging the electrical system. If you do not have a replacement f use with the proper rating f or the circuit, install one with a lower rating.

6.

If the replacement fuse of the same rating blows in a short time, there is probably a serious electrical problem in your vehicle. Leave the blown fuse in that circuit and have your vehicle checked by a qualified mechanic.

206

StandardforValuePackage,HX,LX,EX andSpecialEditionmodelsintheU.S., andDXSpecialEdition,REVERB,LX andSimodelsinCanada If the radio fuse is removed, the audio system will disable itself. The next time you turn on the radio you will see ‘‘ models with in-dash CD changer)/ ‘‘CODE’’ (on models with in-dash CD changer) in the frequency display. Use the preset buttons to enter the five-digit code (see page

’’ (except for

114

).

Onallmodels When the audio system is disabled, the clock setting in the audio system will be canceled. You will need to reset the clock according to the instructions in the Features section