2 If the Smart Entry Remote Battery is Weak P. 552
uMake sure the smart entry remote is in its operating range.
2 ENGINE START/STOP Button Operating Range P. 132
Check brightness of the interior light. Turn on interior lights and check brightness. ● If the interior lights are dim or do not come on at all
2 Battery P. 534
● If the interior lights come on normally
2 Fuses P. 564
Review the engine start procedure.
Follow its instructions, and try to start the engine again. 2 Starting the Engine P. 427
Check the immobilizer system indicator.
When the immobilizer system indicator is blinking, the engine cannot be started.
2 Immobilizer System P. 124
Check the fuel level.
There should be enough fuel in the tank. 2 Fuel Gauge P. 89
Check the fuse.
Check all fuses, or have the vehicle checked by a dealer.
2 Inspecting and Changing Fuses P. 566
If the problem continues:
2 Emergency Towing P. 567
QRG
TOC
Index
Home
551
2013 Accord Sedan13 ACCORD 4D US-31T2A6000.book 552 ページ 2012年10月3日 水曜日 午後4時21分
uuEngine Does Not StartuIf the Smart Entry Remote Battery is Weak
Models with smart entry system If the Smart Entry Remote Battery is Weak If the beeper sounds, the indicator on the ENGINE START/STOP button flashes, and the engine won’t start. Models with multi-information display The To Start, Hold Remote Near Start Button message appears on the multi- information display. All models Start the engine as follows.
1. Touch the center of the ENGINE START/
STOP button with the H logo on the smart entry remote while the indicator on the ENGINE START/STOP button is flashing. The buttons on the smart entry remote should be facing you. u The indicator flashes for about 30
seconds.
2. Depress the brake pedal (automatic
transmission) or clutch pedal (manual transmission) and press the ENGINE START/STOP button within 10 seconds after the beeper sounds and the indicator stays on. u If you don’t depress the pedal, the mode
will change to ACCESSORY.
QRG
TOC
Index
Home
552
2013 Accord Sedan13 ACCORD 4D US-31T2A6000.book 553 ページ 2012年10月3日 水曜日 午後4時21分
Models with smart entry system Emergency Engine Stop If you cannot stop the engine by pressing the ENGINE START/STOP button, do either of the following operations: • Press and hold the ENGINE START/STOP button for about two seconds.
• Firmly press the ENGINE START/STOP button two times.
The steering wheel will not lock. Automatic transmission/CVT models The power mode changes to VEHICLE OFF with the shift lever in (P, and to ACCESSORY with the shift lever in any position other than (P. Manual transmission models The power mode changes to VEHICLE OFF.
uuEngine Does Not StartuEmergency Engine Stop
1Emergency Engine Stop
Do not press the button while driving unless it is absolutely necessary for the engine to be switched off.
QRG
TOC
Index
Home
553
2013 Accord Sedan13 ACCORD 4D US-31T2A6000.book 554 ページ 2012年10月3日 水曜日 午後4時21分
Jump Starting
■ Jump Starting Procedure Turn off the power to electric devices, such as audio and lights. Turn off the engine, then open the hood. 4-cylinder models
1. Connect the first jumper cable to your
vehicle's battery + terminal.
2. Connect the other end of the first jumper
cable to the booster battery + terminal. u Use a 12-volt booster battery only.
3. Connect the second jumper cable to the
booster battery - terminal.
Booster Battery
6-cylinder models
1Jump Starting
3WARNING
A battery can explode if you do not follow the correct procedure, seriously injuring anyone nearby.
Keep all sparks, open flames, and smoking materials away from the battery.
Securely attach the jumper cables clips so that they do not come off when the engine vibrates. Also be careful not to tangle the jumper cables or allow the cable ends to touch each other while attaching or detaching the jumper cables.
QRG
TOC
Booster Battery
Index
Home
554
2013 Accord Sedan13 ACCORD 4D US-31T2A6000.book 555 ページ 2012年10月3日 水曜日 午後4時21分
uuJump Startingu
4-cylinder models
6-cylinder models
4. Connect the other end of the second
1Jump Starting
Battery performance degrades in cold conditions and may prevent the engine from starting.
jumper cable to the engine mounting bolt as shown. Do not connect this jumper cable to any other part.
5. If your vehicle is connected to another
vehicle, start the assisting vehicle's engine and increase its rpm slightly.
6. Attempt to start your vehicle's engine. If it
turns over slowly, check that the jumper cables have good metal-to-metal contact.
Continued
QRG
TOC
Index
Home
555
2013 Accord Sedan13 ACCORD 4D US-31T2A6000.book 556 ページ 2012年10月3日 水曜日 午後4時21分
uuJump Startingu
■ What to Do After the Engine Starts Once your vehicle's engine has started, remove the jumper cables in the following order.
1. Disconnect the jumper cable from your vehicle's ground.
2. Disconnect the other end of the jumper cable from the booster battery -
terminal.
3. Disconnect the jumper cable from your vehicle's battery + terminal.
4. Disconnect the other end of the jumper cable from the booster battery +
terminal.
Have your vehicle inspected by a nearby service station or a dealer.
QRG
TOC
Index
Home
556
2013 Accord Sedan13 ACCORD 4D US-31T2A6000.book 557 ページ 2012年10月3日 水曜日 午後4時21分
Shift Lever Does Not Move
Automatic transmission/CVT models Follow the procedure below if you cannot move the shift lever out of the (P position.
■ Releasing the Lock
1. Set the parking brake. Models without smart entry system
2. Remove the key from the ignition switch. Models with smart entry system 2. Remove the built-in key from the smart
Slot
entry remote.
Cover
Shift Lock Release Slot
Release Button
All models 3. Wrap a cloth around the tip of a small flat-
tip screwdriver. Put it into the shift lock release slot as shown in the image, and remove the cover.
4. Insert the key into the shift lock release slot.
5. While pushing the key down, press the shift lever release button and place the shift lever into (N. u The lock is now released. Have the shift
lever checked by a dealer as soon as possible.
QRG
TOC
Index
Home
557
2013 Accord Sedan1How to Handle Overheating
3WARNING
Steam and spray from an overheated engine can seriously scald you.
Do not open the hood if steam is coming out.
NOTICE Continuing to drive with the temperature gauge needle at the mark may damage the engine.
13 ACCORD 4D US-31T2A6000.book 558 ページ 2012年10月3日 水曜日 午後4時21分
Overheating
QRG
How to Handle Overheating Overheating symptoms are as follows: • The temperature gauge needle is at the
power.
mark or the engine suddenly loses
• Steam or spray comes out of the engine compartment.
■ First thing to do 1. Immediately park the vehicle in a safe place.
2. Turn off all accessories and turn on the hazard warning lights.
u No steam or spray present: Keep the engine running and open the hood. u Steam or spray is present: Turn off the engine and wait until it subsides.
Then open the hood.
TOC
Index
Home
558
2013 Accord Sedan13 ACCORD 4D US-31T2A6000.book 559 ページ 2012年10月3日 水曜日 午後4時21分
■ Next thing to do
Reserve Tank
MAX MIN
uuOverheatinguHow to Handle Overheating
1How to Handle Overheating
3WARNING
Removing the radiator cap while the engine is hot can cause the coolant to spray out, seriously scalding you.
Always let the engine and radiator cool down before removing the radiator cap.
If the coolant is leaking, contact a dealer for repairs.
Use water as an emergency/temporary measure only. Have a dealer flush the system with proper antifreeze as soon as possible.
1. Check that the cooling fan is operating and
stop the engine once the temperature gauge needle comes down. u If the cooling fan is not operating,
immediately stop the engine.
2. Once the engine has cooled down, inspect
the coolant level and check the cooling system components for leaks. u If the coolant level in the reserve tank is
low, add coolant until it reaches the MAX mark.
u If there is no coolant in the reserve tank, check that the radiator is cool. Cover the radiator cap with a heavy cloth and open the cap. If necessary, add coolant up to the base of the filler neck, and put the cap back on.
■ Last thing to do Once the engine has cooled sufficiently, restart it and check the temperature gauge. If the temperature gauge needle has gone down, resume driving. If it has not gone down, contact a dealer for repairs.
QRG
TOC
Index
Home
559
2013 Accord Sedan13 ACCORD 4D US-31T2A6000.book 560 ページ 2012年10月3日 水曜日 午後4時21分
Indicator, Coming On/Blinking
QRG
If the Low Oil Pressure Indicator Comes On
■ Reasons for the indicator to come on Comes on when the engine oil pressure is low.
■ What to do as soon as the indicator comes on 1. Immediately park the vehicle in a safe place.
2. If necessary, turn the hazard warning lights on. ■ What to do after parking the vehicle 1. Stop the engine and let it sit for about one minute.
2. Open the hood and check the oil level.
u Add oil as necessary.
3. Start the engine and check the low oil pressure indicator.
u The light goes out: Start driving again. u The light does not go out within 10 seconds: Stop the engine and
contact a dealer for repairs immediately.
If the Charging System Indicator Comes On
■ Reasons for the indicator to come on Comes on when the battery is not being charged. ■ What to do when the indicator comes on Turn off the heating and cooling system * /climate control system *, rear defogger, and other electrical systems, and immediately contact a dealer for repairs.
TOC
Index
Home
560
1If the Low Oil Pressure Indicator Comes On
NOTICE Running the engine with low oil pressure can cause serious mechanical damage almost immediately.
1If the Charging System Indicator Comes On
If you need to stop temporarily, do not turn off the engine. Restarting the engine may rapidly discharge the battery.
* Not available on all models
2013 Accord Sedan13 ACCORD 4D US-31T2A6000.book 561 ページ 2012年10月3日 水曜日 午後4時21分
uuIndicator, Coming On/BlinkinguIf the Malfunction Indicator Lamp Comes On or Blinks
If the Malfunction Indicator Lamp Come On or Blinks
■ Reasons for the indicator lamp to come on or blink • Comes on when there is a problem with the engine emissions control
system, or the fuel fill cap is missing, or loose.
• Blinks when engine misfiring is detected. ■ What to do when the indicator lamp comes on Avoid high speeds and immediately get your vehicle inspected at a dealer. ■ What to do when the indicator lamp blinks Park the vehicle in a safe place with no flammable items and wait at least ten minutes or more with the engine stopped until it cools.
1If the Malfunction Indicator Lamp Comes On or Blinks
NOTICE If you drive with the malfunction indicator lamp on, the emissions control system and the engine could be damaged.
If the malfunction indicator lamp blinks again when restarting the engine, drive to the nearest dealer at 31 mph (50 km/h) or less. Have your vehicle inspected.
■ Check/Tighten Fuel Cap Message ■ The message appears on when: An evaporative system leak is detected. This may be caused by the fuel fill cap being loose or not being installed.
■ What to do when the message appears: 1. Stop the engine. 2. Check that the fuel fill cap is fully installed.
u If not, loosen the cap, and then retighten it until it clicks at least once.
3. Drive for several days of normal driving.
u The message should go off.
■ When the malfunction indicator lamp comes on Malfunction indicator lamp comes on if the system continues to detect a leak of gasoline vapor. If this happens, check the fuel fill cap using the procedures described above.
QRG
TOC
Index
Home
561
2013 Accord Sedan13 ACCORD 4D US-31T2A6000.book 562 ページ 2012年10月3日 水曜日 午後4時21分
uuIndicator, Coming On/BlinkinguIf the Brake System Indicator (Red) Comes On
QRG
If the Brake System Indicator (Red) Comes On
U.S.
■ Reasons for the indicator to come on • The brake fluid is low.
Canada
• There is a malfunction in the brake system. ■ What to do when the indicator comes on while driving Press the brake pedal lightly to check pedal pressure. • If normal, check the brake fluid level the next time you stop.
• If abnormal, take immediate action. If necessary, downshift the
transmission to slow the vehicle using engine braking.
If the EPS System Indicator Comes On
■ Reasons for the indicator to come on • Comes on when there is a problem with the EPS system.
• If you depress the accelerator pedal repeatedly to increase the engine
speed while the engine is idling, the indicator comes on, and sometimes the steering wheel becomes harder to operate.
■ What to do when the indicator comes on Stop the vehicle in a safe place and restart the engine. If the indicator comes on and stays on, immediately have your vehicle inspected by a dealer.
TOC
Index
Home
562
1If the Brake System Indicator (Red) Comes On Have your vehicle repaired immediately. It is dangerous to drive with low brake fluid. If there is no resistance from the brake pedal, stop immediately in a safe place. If necessary downshift the gears.
If the brake system indicator and ABS indicator come on simultaneously, the electronic brake distribution system is not working. This can result in vehicle instability under sudden braking. Have your vehicle inspected by a dealer immediately.
1If the EPS System Indicator Comes On
NOTICE If you repeatedly turn the steering wheel at an extremely low speed, or hold the steering wheel on the full left or right position for a while, the system heats up. The system goes into a protective mode, and limits its performance. The steering wheel becomes harder and harder to operate. Once the system cools down, EPS is restored. Repeated operation under these conditions can eventually damage the system.
2013 Accord Sedan13 ACCORD 4D US-31T2A6000.book 563 ページ 2012年10月3日 水曜日 午後4時21分
uuIndicator, Coming On/BlinkinguIf the Low Tire Pressure/TPMS Indicator Comes On or Blinks
If the Low Tire Pressure/TPMS Indicator Comes on or Blinks
■ Reasons for the indicator to come on or blink A tire pressure is significantly low, or the TPMS has not been calibrated. If there is a problem with the TPMS or the compact spare tire is installed, the indicator blinks for about one minute, and then stays on. ■ What to do when the indicator comes on Drive carefully and avoid abrupt cornering and hard braking. Stop your vehicle in a safe place. Check the tire pressure and adjust the pressure to the specified level. The specified tire pressure is on a label on the driver side doorjamb.
uCalibrate the TPMS after the tire pressure is adjusted.
■ What to do when the indicator blinks, then remains on Have the tire inspected by a dealer as soon as possible. If the compact spare tire causes the indicator to blink, change the tire to a full-size tire. The indicator goes off after driving for a few miles (kilometers).
uCalibrate the TPMS after a full-size tire is reinstalled.
1If the Low Tire Pressure/TPMS Indicator Comes On or Blinks
NOTICE Driving on an extremely underinflated tire can cause it to overheat. An overheated tire can fail. Always inflate your tires to the prescribed level.
QRG
TOC
Index
Home
563
2013 Accord Sedan13 ACCORD 4D US-31T2A6000.book 564 ページ 2012年10月3日 水曜日 午後4時21分
Fuses
QRG
Fuse Locations If any electrical devices are not working, turn the ignition switch to LOCK (0 *1 and check to see if any applicable fuse is blown.
■ Engine Compartment Fuse Box Located near the brake fluid reservoir. Push the tabs to open the box. Fuse locations are shown on the fuse box cover. Locate the fuse in question by the fuse number and box cover number.
Circuit Protected
Amps
10
11
− − − −
Front Fog Light *
Horn
Stop Light
FI Sub DRL
IG Coil
Injector*2
Hazard
Fuse Box Main 2
Fuse Box Option 2
IG Main 1
IG Main 2*4
− − − −
(15 A)
10 A
10 A
15 A
(7.5 A)
15 A
20 A
15 A
60 A
(40 A)
50 A
30 A*4
30 A
20 A*2
30 A*3
30 A
30 A
30 A
30 A
30 A
40 A
40 A
15 A
Circuit Protected Heated Door Mirror *
MG Clutch
DBW
Small Light Interior Light
Back Up Audio
Fan Timer
16
17
18
19
20
21
22
23
24 Right Headlight Low Beam
25
26
Left Headlight Low Beam
−
Amps
(10 A)
7.5 A
15 A
20 A
7.5 A
10 A
10 A
7.5 A
10 A
15 A*5
10 A
15 A*5
−
*1: Models with the smart entry system have an
ENGINE START/STOP button instead of an ignition switch.
*2:4-cylinder models *3:6-cylinder models *4:Models with smart entry system *5:Models with LED low beam headlights
* Not available on all models
■ Circuit protected and fuse rating
Circuit Protected
Battery
EPS
Fuse Box Main 1
Fuse Box Option 1
− −
ABS/VSA FSR ABS/VSA Motor
Amps 125 A 70 A (60 A) (40 A)
− −
40 A 30 A
12
Sub Fan Motor
Headlight Low Beam Main
Fuse Box
Wiper Motor
Main Fan Motor
Starter Motor*4
Rear Defogger
Heater Motor
FI Main
13
14
15
TOC
Index
Home
564
2013 Accord Sedan13 ACCORD 4D US-31T2A6000.book 565 ページ 2012年10月3日 水曜日 午後4時21分
uuFusesuFuse Locations
■ Interior Fuse Box Located under the dashboard.
Fuse Label
Fuse locations are shown on the label on the side panel. Locate the fuse in question by the fuse number and label number.
■ Circuit protected and fuse rating
Circuit Protected
A/C DRL − −
Meter SRS
Option * MISS SOL Fuel Pump
Amps 7.5 A 7.5 A
− −
7.5 A 7.5 A (7.5 A) 10 A 20 A
* Not available on all models
Circuit Protected
ABS/VSA
−
Front Wiper
ACG
Rear Accessory Power Socket
(Console Compartment) Driver’s Power Seat
Reclining * Moonroof *
Front Seat Heaters *
−
Passenger Side Door
Unlock
Driver Side Rear Door
Unlock
10
11
12
13
14
15
16
17
18
19
20
Amps 7.5 A
−
7.5 A 15 A
(20 A)
(20 A)
(20 A) (20 A)
−
10 A
10 A
SRS
Illumination
Driver’s Door Lock
Driver’s Door Unlock
Passenger Side Door Lock
10 A
21
10 A
22
10 A
23
10 A
24
10 A
25
7.5 A
26
10 A
27
28
(10 A)
29 Right Headlight High Beam 10 A
30
15 A
(10 A)
31
32
20 A
Driver’s Power Window
Washer SMART *
Lumbar Support *
Parking Lights
Key Lock
Circuit Protected
Front Passenger’s Power
Window
Rear Driver Side Power
Window
Rear Passenger Side Power
Window
33
34
35
ACCESSORY
36 Driver’s Power Seat Sliding *
37
38
39
Left Headlight High Beam Accessory Power Socket
−
40
(Console Panel)
Door Lock
Audio * ACM *
41 Driver Side Rear Door Lock
42
Rear Seat Heaters *
Premium Amp *
− −
Passenger’s Power Seat
Reclining *
Passenger’s Power Seat
Sliding *
Amps
20 A
20 A
20 A
(20 A) 7.5 A
−
10 A
20 A
10 A 20 A (7.5 A) (20 A) (15 A) (20 A)
− −
(20 A)
(20 A)
QRG
TOC
Index
Home
565
2013 Accord Sedan13 ACCORD 4D US-31T2A6000.book 566 ページ 2012年10月3日 水曜日 午後4時21分
uuFusesuInspecting and Changing Fuses
QRG
Inspecting and Changing Fuses
1. Turn the ignition switch to LOCK (0 *1. Turn
1Inspecting and Changing Fuses
Blown Fuse
headlights and all accessories off.
2. Remove the fuse box cover.
3. Check the large fuse in the engine
compartment. u If the fuse is blown, use a Phillips-head
screwdriver to remove the screw and replace it with a new one.
4. Inspect the small fuses in the engine compartment and the vehicle interior. u If there is a burned out fuse, remove it
with the fuse puller and replace it with a new one.
Combined Fuse
Fuse Puller
NOTICE Replacing a fuse with one that has a higher rating greatly increases the chances of damaging the electrical system.
Replace fuse with a spare fuse of the same specified amperage. Confirm the specified amperage using the charts on P. 564 to 565.
There is a fuse puller on the back of the engine compartment fuse box cover.
*1:
Models
with the smart
entry system have an ENGINE START/STOP button instead of an ignition switch.
TOC
Index
Home
566
2013 Accord Sedan13 ACCORD 4D US-31T2A6000.book 567 ページ 2012年10月3日 水曜日 午後4時21分
Emergency Towing
Call a professional towing service if you need to tow your vehicle.
1Emergency Towing
■ Flat bed equipment The operator loads your vehicle on the back of a truck. This is the best way to transport your vehicle.
■ Wheel lift equipment The tow truck uses two pivoting arms that go under the front tires and lift them off the ground. The rear tires remain on the ground. This is an acceptable way to tow your vehicle.
NOTICE Trying to lift or tow your vehicle by the bumpers will cause serious damage. The bumpers are not designed to support the vehicle's weight.
NOTICE Improper towing such as towing behind a motorhome or other motor vehicle can damage the transmission.
Never tow your vehicle with just a rope or chain. It is very dangerous, since ropes or chains may shift from side to side or break.
QRG
TOC
Index
Home
567
2013 Accord Sedan13 ACCORD 4D US-31T2A6000.book 568 ページ 2012年10月3日 水曜日 午後4時21分
QRG
Index
Home
568
2013 Accord Sedan13 ACCORD 4D US-31T2A6000.book 569 ページ 2012年10月3日 水曜日 午後4時21分
Information
QRG
This chapter includes your vehicle's specifications, locations of identification numbers, and other information required by regulation.
Specifications .................................... 570
Identification Numbers
Vehicle Identification Number (VIN)...... 574
Engine Number and Transmission
Number...................................... 574
Devices that Emit Radio Waves ....... 575
Reporting Safety Defects ................. 576
Emissions Testing
Testing of Readiness Codes.............. 577
Warranty Coverages ........................ 579
Authorized Manuals......................... 581
Customer Service Information......... 582
Index
Home
569
2013 Accord Sedan13 ACCORD 4D US-31T2A6000.book 570 ページ 2012年10月3日 水曜日 午後4時21分
Specifications
QRG
■ Engine Specifications Displacement
144 cu-in (2,356 cm3) NGK DENSO
DILKAR7G11GS DXE22HQR-D11S
Spark Plugs
■ Fuel Fuel: Type Fuel Tank Capacity ■ Battery
Capacity/Type
Unleaded gasoline, Pump octane number of 87 or higher 17.2 US gal (65 ℓ)
36AH(5)/45AH(20)
38AH(5)/47AH(20)
52AH(5)/65AH(20)*3
*3: Canadian models ■ Washer Fluid
Tank Capacity
U.S.: 2.6 US qt (2.5 ℓ) Canada: 5.12 US qt (4.85 ℓ)
Honda Accord Sedan
4-cylinder models ■ Vehicle Specifications Model No. of Passengers: Front Rear Total Weights: Gross Vehicle Weight Rating
U.S.: 4,200 lbs (1,905 kg)*1
4,321 lbs (1,960 kg)*2
Canada: 1,930 kg*1
1,980 kg*2
Gross Axle Weight Rating (Front)
Gross Axle Weight Rating (Rear)
Air Conditioning: Refrigerant Type Charge Quantity Lubricant Type *1: LX models *2: Except LX models
U.S.: 2,249 lbs (1,020 kg)*1
2,315 lbs (1,050 kg)*2
Canada: 1,030 kg*1
1,065 kg*2
U.S.: 2,006 lbs (910 kg)*1
2,050 lbs (930 kg)*2
Canada: 910 kg*1
930 kg*2
HFC-134a (R-134a)
15.0 – 16.8 oz (425 – 475 g)
ND-OIL 8
TOC
Index
Home
570
■ Light Bulbs
Headlights (Low Beam)
55W (H11) LED * 60W (HB3) 35W (H8) 5W LED
Headlights (High Beam) Fog Lights * Parking Lights * Parking/Daytime Running Lights * Front Turn Signal/Side Marker Lights 24/2.2CP (Amber) Side Turn Signal Lights (on Door Mirrors) * Brake/Taillights/Rear Side Marker Lights * Brake/Taillights * Rear Side Marker Lights *
21/5W
LED
LED LED 3CP LED * 16W 21W (Amber) LED 5W 5W
Taillights
Back-Up Lights Rear Turn Signal Lights High-Mount Brake Light Rear License Plate Lights Trunk Light Interior Lights
Map Lights Ceiling Light Vanity Mirror Lights * 1.4W Courtesy Lights * 2CP
8W 8W
* Not available on all models
2013 Accord Sedan13 ACCORD 4D US-31T2A6000.book 571 ページ 2012年10月3日 水曜日 午後4時21分
■ Brake/Clutch Fluid
Specified
Honda Heavy Duty Brake Fluid DOT 3
■ Automatic Transmission (CVT) Fluid
Specified
Capacity
■ Manual Transmission Fluid
Specified
Capacity
Honda Manual Transmission Fluid Change
3.7 US qt (3.5 ℓ)
2.0 US qt (1.9 ℓ)
HCF-2
Change
■ Engine Oil
Capacity
Recommended
4.2 US qt (4.0 ℓ)
·Genuine Honda Motor Oil 0W-20
·API Premium-grade 0W-20 detergent oil
Change
Change
including
filter
■ Engine Coolant
Specified
Ratio
Honda Long-Life Antifreeze/Coolant Type2
50/50 with distilled water
1.65 US gal (6.25 ℓ)
(change including the remaining
0.17 US gal (0.64 ℓ) in the reserve tank)
4.4 US qt (4.2 ℓ)
Capacity
uuSpecificationsu
QRG
■ Tire
Size
Regular
Pressure psi (kPa [kgf/cm2])
Front
Rear
Compact Spare
Size Pressure psi (kPa [kgf/cm2])
Wheel Size
Regular
Compact Spare
205/65R16 95H*1
215/55R17 94V*2
235/45R18 94V*3
33 (230 [2.3])*1
33 (225 [2.3])*2, *3
32 (220 [2.2])*1, *3
33 (225 [2.3])*2
T125/80D16 97M
60 (420 [4.2])
16 x 7J*1
17 x 7 1/2J*2
18 x 8J*3
16 x 4T
*1: U.S. LX models *2: U.S. EX, EX-L models and Canadian LX, EX, EX-L models *3: U.S. Sport models and Canadian Sport, Touring models
TOC
Index
Home
Continued
571
2013 Accord Sedan13 ACCORD 4D US-31T2A6000.book 572 ページ 2012年10月3日 水曜日 午後4時21分
uuSpecificationsu
QRG
Honda Accord Sedan
6-cylinder models ■ Vehicle Specifications Model No. of Passengers: Front Rear Total Weights: Gross Vehicle Weight Rating Gross Axle Weight Rating (Front)
U.S.: 4,542 lbs (2,060 kg) Canada: 2,060 kg
U.S.: 2,491 lbs (1,130 kg) Canada: 1,130 kg
Gross Axle Weight Rating (Rear)
Air Conditioning: Refrigerant Type Charge Quantity Lubricant Type
U.S.: 2,072 lbs (940 kg) Canada: 940 kg
HFC-134a (R-134a)
15.0 – 16.8 oz (425 – 475 g)
ND-OIL 8
TOC
Index
Home
572
■ Engine Specifications Displacement
212 cu-in (3,471 cm3) NGK DENSO
ILZKR7B11
SXU22HCR11
Spark Plugs
■ Fuel Fuel: Type Fuel Tank Capacity ■ Battery Capacity/Type ■ Washer Fluid
Unleaded gasoline, Pump octane number of 87 or higher 17.2 US gal (65 ℓ)
60AH(5)/72AH(20)
Tank Capacity
U.S.: 2.6 US qt (2.5 ℓ) Canada: 5.12 US qt (4.85 ℓ)
■ Light Bulbs
Headlights (Low Beam)
55W (H11) LED * 60W (HB3) 35W (H8) 5W LED
LED
Headlights (High Beam) Fog Lights Parking Lights * Parking/Daytime Running Lights * Front Turn Signal/Side Marker Lights 24/2.2CP (Amber) Side Turn Signal Lights (on Door Mirrors) Brake/Taillights Rear Side Marker Lights Taillights Back-Up Lights Rear Turn Signal Lights High-Mount Brake Light Rear License Plate Lights Trunk Light Interior Lights
LED LED LED 16W 21W (Amber) LED 5W 5W
Map Lights Ceiling Light Vanity Mirror Lights Courtesy Lights
8W 8W 1.4W 2CP
* Not available on all models
2013 Accord Sedan13 ACCORD 4D US-31T2A6000.book 573 ページ 2012年10月3日 水曜日 午後4時21分
■ Brake Fluid Specified ■ Automatic Transmission Fluid
Honda Heavy Duty Brake Fluid DOT 3
Specified
Capacity
Honda ATF DW-1
(automatic transmission fluid)
Change
3.3 US qt (3.1 ℓ)
■ Engine Oil
Capacity
Recommended
4.2 US qt (4.0 ℓ)
·Genuine Honda Motor Oil 0W-20
·API Premium-grade 0W-20 detergent oil
Change
Change
including
filter
■ Engine Coolant
Specified
Ratio
Honda Long-Life Antifreeze/Coolant Type2
50/50 with distilled water
1.7 US gal (6.5 ℓ)
(change including the remaining
0.17 US gal (0.64 ℓ) in the reserve tank)
4.5 US qt (4.3 ℓ)
Capacity
uuSpecificationsu
QRG
■ Tire
Regular
Compact Spare
Size
Pressure psi (kPa [kgf/cm2]) Front
Rear
Size Pressure psi (kPa [kgf/cm2])
Wheel Size
Regular
Compact Spare
215/55R17 94V*1
235/45R18 94V*2
33 (225 [2.3])
33 (225 [2.3])*1
32 (220 [2.2])*2
T125/80D16 97M
60 (420 [4.2])
17 x 7 1/2J*1
18 x 8J*2
16 x 4T
*1: U.S. models and Canadian EX-L V6 models *2: Canadian V6 Touring models
TOC
Index
Home
573
2013 Accord Sedan13 ACCORD 4D US-31T2A6000.book 574 ページ 2012年10月3日 水曜日 午後4時21分
Identification Numbers
QRG
Vehicle Identification Number (VIN) Your vehicle has a 17-digit vehicle identification number (VIN) used to register your vehicle for warranty purposes, and for licensing and insuring your vehicle. See the image below for the VIN locations.
1Vehicle Identification Number (VIN)
The interior vehicle identification number (VIN) is located under the cover.
Engine Number and Transmission Number See the image below for the locations of your vehicle's engine number and transmission number.
Vehicle Identification Number
Cover
4-cylinder models Engine Number
Automatic Transmission (CVT) Number Manual Transmission Number
6-cylinder models
Engine Number
Automatic Transmission Number
TOC
Index
Home
574
Certification Label/ Vehicle Identification Number
2013 Accord Sedan13 ACCORD 4D US-31T2A6000.book 575 ページ 2012年10月3日 水曜日 午後4時21分
Devices that Emit Radio Waves
The following products and systems on your vehicle emit radio waves when in operation. Audio System Bluetooth® Audio Bluetooth® HandsFreeLink® HomeLink® Universal Transceiver Immobilizer System Keyless Access System Remote Transmitter
Each of the above complies with the appropriate requirements or the required standards of FCC (Federal Communications Commission) and Industry Canada Standard, described below:
As required by the FCC: This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This device complies with Industry Canada Standard RSS-Gen/210/310. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
QRG
TOC
Index
Home
575
2013 Accord Sedan13 ACCORD 4D US-31T2A6000.book 576 ページ 2012年10月3日 水曜日 午後4時21分
Reporting Safety Defects
QRG
In the U.S. If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying American Honda Motor Co., Inc.
If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your dealer, or American Honda Motor Co., Inc.
To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at 1-888-327-4236 (TTY: 1-800-424-9153);
go to http://www.safercar.gov; or write to: Administrator, NHTSA,
1200 New Jersey Avenue, SE., Washington, DC 20590.
You can also obtain othe r information about motor vehicle safety from http://www.safercar.gov.
In Canada If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform Honda Canada Inc. and you may also inform Transport Canada.
If Transport Canada receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may lead to a recall and remedy campaign. However, Transport Canada cannot become involved in individual problems between you, your dealer, or Honda Canada Inc.
To contact Transport Canada’s Defect Investigations and Recalls Division, you may call 1-800-333-0510. For more information on reporting safety defects or about motor vehicle safety, go to http://www.tc.gc.ca/roadsafety
TOC
Index
Home
576
2013 Accord Sedan13 ACCORD 4D US-31T2A6000.book 577 ページ 2012年10月3日 水曜日 午後4時21分
Emissions Testing