2011 Honda Accord Sedan Owners Manual

Never try to insert foreign objects in the disc changer.

Protecting Your Discs

Handle a disc by its edges; never touch either surface. Do not place stabilizer rings or labels on the disc. These, along with contamination from finger prints, liquids, and felt- tip pens, can cause the disc to not play properly, or possibly jam in the drive.

245

2011 Accord Sedan10/06/18 16:13:49 31TA5630_251

Protecting Your Discs

Additional Information on Recommended Discs The in-dash disc player/changer has a sophisticated and delicate mechanism. If you insert a damaged disc as indicated in this section, it may become stuck inside and damage the audio unit.

Examples of these discs are shown to the right:

1.

Bubbled, wrinkled, labeled, and excessively thick discs

Bubbled/ Wrinkled

With Label/ Sticker

Using Printer Label Kit

Sealed

With Plastic Ring

2.

Damaged discs

3.

Poor quality discs

Chipped/ Cracked

Warped

Burrs

246

2011 Accord Sedan10/06/18 16:13:59 31TA5630_252

4.

Small, irregular shaped discs

5.

Discs with scratches, dirty discs

3-inch (8-cm) CD

Triangle Shape

Fingerprints, scratches, etc.

CD-R or CD-RW may not play due to the recording conditions.

Scratches and fingerprints on the discs may cause the sound to skip.

Can Shape

Arrow Shape

Protecting Your Discs

Recommended discs are printed with the following logo.

Audio unit may not play the following formats.

This audio unit cannot play a Dual- disc .

247

2011 Accord Sedan10/06/18 16:14:08 31TA5630_253

FM/AM Radio Reception

FM/AM Radio Frequencies The radio can receive the complete AM and FM bands. Those bands cover these frequencies: AM band: 530 to 1,710 kHz FM band: 87.7 to 107.9 MHz

Radio stations on the AM band are assigned frequencies at least 10 kHz apart (530, 540, 550). Stations on the FM band are assigned frequencies at least 0.2 MHz apart (87.9, 88.1, 88.3).

Stations must use these exact frequencies. It is fairly common for stations to round-off the frequency in their advertising, so your radio could display a frequency of 100.9 even though the announcer may identify the station as ‘‘FM101.’’

FM/AM Radio Reception How well the radio receives stations is dependent on many factors, such as the distance from the station’s transmitter, nearby large objects, and atmospheric conditions.

A radio station’s signal gets weaker as you get farther away from its transmitter. If you are listening to an AM station, you will notice the sound volume becoming weaker, and the station drifting in and out. If you are listening to an FM station, you will see the stereo indicator flickering off and on as the signal weakens. Eventually, the stereo indicator will go off and the sound will fade completely as you get out of range of the station’s signal.

248

Driving very near the transmitter of a station that is broadcasting on a frequency close to the frequency of the station you are listening to can also affect your radio’s reception. You may temporarily hear both stations, or hear only the station you are close to.

2011 Accord Sedan10/06/18 16:14:14 31TA5630_254

FM/AM Radio Reception

AsrequiredbytheFCC: Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser’s authoritytooperatetheequipment.

249

Radio signals, especially on the FM band, are deflected by large objects such as buildings and hills. Your radio then receives both the direct signal from the station’s transmitter, and the deflected signal. This causes the sound to distort or flutter. This is a main cause of poor radio reception in city driving.

Radio reception can be affected by atmospheric conditions such as thunderstorms, high humidity, and even sunspots. You may be able to receive a distant radio station one day and not receive it the next day because of a change in conditions.

Electrical interference from passing vehicles and stationary sources can cause temporary reception problems.

2011 Accord Sedan10/06/18 16:14:20 31TA5630_255

Remote Audio Controls

MODE BUTTON

▲

) or down (

The VOL button adjusts the volume up ( ). Press the top or bottom of the button, hold it until the desired volume is reached, then release it.

▼

VOL BUTTON

CH BUTTON

Three controls for the audio system are mounted in the steering wheel hub. These let you control basic functions without removing your hand from the wheel.

The MODE button changes the mode. Pressing the button repeatedly selects FM1, FM2, AM, disc (if a disc(s) is loaded) or AUX (if an appropriate audio unit is connected). On models with XM Radio, you can also select XM1 and XM2.

If an iPod or a USB flash memory device is plugged into the system, you can also select AUX.

250

＋

If you are listening to the radio, use the CH button to change stations. Each time you press the top ( ) of the button, the system goes to the next preset station on the band you are listening to. Press the bottom − preset station. If you press and hold the CH button ( ), the system goes into the skip (seek) mode. It stops when it finds a station with a strong signal.

) to go back to the previous

) or (

＋

−

2011 Accord Sedan10/06/18 16:14:26 31TA5630_256

Remote Audio Controls

If you are playing a disc, iPod or USB flash memory device, the system skips to the beginning of the next track/file each time you press the top ( bottom ( beginning of the current track/file. Press it twice to return to the previous track/file.

) of the CH button. Press the

) to return to the

＋

−

You can also use the skip function to select folders. Press and hold the top ) of the CH button until you hear ＋ a beep, to skip forward to the first file in the next folder. Press the bottom ( previous folder.

) to skip backward to the

−

Onmodelswithin-dashdiscchanger If you are playing a conventional CD (without the text data and not compressed in MP3 or WMA), you can use the skip function to select discs. Press and hold the top ( ) of ＋ the CH button until you hear a beep, to skip forward to the next disc. Press and hold the bottom ( ) to skip backward to the previous disc.

−

＋

) of the CH button to skip

EX,EX-LandV6models If you are playing a USB flash memory device or iPod with the USB adapter cable, press and release the top ( forward to the beginning of the next file. Press the bottom ( ) to skip backward to the beginning to the current file. Press it twice to return to the previous file.

−

When playing a USB flash memory device, you can also use the seek function to skip the folder. To activate this, press and hold either side of the CH button until you hear a beep.

251

2011 Accord Sedan10/06/18 16:14:31 31TA5630_257

Auxiliary Input Jack

EX, EX-L and V6 models

LX, LX-P and SE models

The auxiliary input jack is inside the console compartment. The system will accept auxiliary input from standard audio accessories using a 1/8 inch (3.5 mm) stereo miniplug.

When you plug in a mini-jack cable between a compatible audio unit and the jack, you will see AUX in the display and the system automatically switches to AUX mode.

When a compatible audio unit is connected to the jack, press the AUX or CD/AUX button to select it.

252

2011 Accord Sedan10/06/18 16:14:37 31TA5630_258

ExceptLX,LX-PandU.S.SE Your vehicle’s audio system may disable itself if it is disconnected from electrical power for any reason. To make it work again, you must enter a specific five-digit code with the preset buttons. Because there are hundreds of number combinations possible from the five digits, making the system work without knowing the exact code is nearly impossible.

You should have received a radio code card that lists your audio system’s code and serial numbers. It is best to store this card in a safe place at home. In addition, you should write the audio system’s serial number in this owner’s manual.

If you lose the card, you must obtain the code number from your dealer. To do this, you will need the audio system’s serial number.

If your vehicle’s battery is discon- nected or goes dead, the audio system will disable itself. If this happens, you will see ‘‘ENTER CODE’’ in the frequency display (on the screen on models with navigation system) the next time you turn on the system. Use the preset buttons to enter the five-digit code. The code is on the radio code card included in your owner’s manual kit. When it is entered correctly, the radio will start playing.

If you make a mistake entering the code, do not start over; complete the five-digit sequence, then enter the correct code. You have ten tries to enter the correct code. If you are unsuccessful in ten attempts, you must then leave the system on for 1
hour before trying again.

Radio Theft Protection

The system will retain your AM and FM presets even if power is disconnected.

253

2011 Accord Sedan10/06/18 16:14:46 31TA5630_259

Setting the Clock

Onmodelswithoutnavigationsystem To set the time, press the CLOCK button until you hear a beep. The displayed time begins to blink.

Change the hours by pressing the H (hour) button until the numbers advance to the desired time. Change the minutes by pressing the M (minute) button until the numbers advance to the desired time.

Press the CLOCK button again to enter the set time.

You can quickly set the time to the nearest hour. If the displayed time is before the half hour, press and hold the CLOCK button, then press the R (reset) button to set the time back to the previous hour. If the displayed time is after the half hour, the same procedure sets the time forward to the beginning of the next hour.

254

On models without navigation system

RESET BUTTON (PRESET 6) CLOCK BUTTON

U.S. EX-L is shown.

For example:

1:06 would RESET to 1:00. 1:52 would RESET to 2:00.

HOUR BUTTON (PRESET 4)

MINUTE BUTTON (PRESET 5)

Onmodelswithnavigationsystem The navigation system receives signals from the global positioning system (GPS), and the displayed time is updated automatically by the GPS. Refer to the navigation system manual for how to adjust the time.

2011 Accord Sedan10/06/18 16:14:57 31TA5630_260

EX,EX-L,CanadianSE,andV6models withoutnavigationsystem AdjustingtheClockwithMENU Button You can also adjust the clock and switch the clock display between 24-hours and 12-hours in the menu mode.

To adjust the clock setting:

1.

Press and release the MENU button. The display shows you the menu items. You can adjust the clock setting with the ignition switch in the ACCESSORY (I) or ON (II) position.

Setting the Clock

2.

Turn the selector knob to select ‘‘CLOCK ADJUST.’’

4.

3.

Press the selector knob (ENTER) to enter your selection. The display changes to the clock adjusting display.

Turn the selector knob to select the item which you want to adjust. Turning the selector knob will change the selected item between the clock display setting, hours, minutes, and SET. The selected item is indicated with in the display.

△

CONTINUED

255

2011 Accord Sedan10/06/18 16:15:08 31TA5630_261

Setting the Clock

5.

Turn the selector knob to change the setting between 12H and 24H.

8.

Turn the selector knob to count the numbers up or down.

10.

MINUTE SETTING

6.

7.

Press the selector knob (ENTER) to enter your selection. The display will return to the clock adjusting display.

9.

Press the selector knob (ENTER) to enter your selection. The display will return to the clock adjusting display.

To set the time, turn the selector knob and select the hours or the minutes, then press the knob to enter your selection. The display changes to the setting display.

While setting the clock, pressing the RETURN button will go back to the previous display. Pressing the MENU button again will cancel this setting mode.

256

To enter the clock setting, turn the selector knob to select ‘‘SET,’’ then press the knob. The display will return to the menu item display.

11.

Press either the RETURN or MENU button to go back to the normal display.

2011 Accord Sedan10/06/18 16:15:15 31TA5630_262

ExceptLX The security system helps to protect your vehicle and valuables from theft. The horn sounds and a combination of headlights, parking lights, side marker lights and taillights flashes if someone attempts to break into your vehicle or remove the audio unit. This alarm continues for two minutes, then the system resets. To reset an activated system before the two minutes have elapsed, unlock the driver’s door with the key or the remote transmitter.

The security system automatically sets 15 seconds after you lock the doors, hood, and trunk. For the system to activate, you must lock the doors from the outside with the key, driver’s lock tab, door lock master switch, or remote transmitter. The security system indicator on the instrument panel starts blinking immediately to show you the system is setting itself.

SECURITY SYSTEM INDICATOR

Once the security system is set, opening any door (without using the key or the remote transmitter), the hood, or the trunk will cause the alarm to activate. It will also activate if the audio unit is removed from the dashboard or the wiring is cut.

Security System

With the system set, you can still open the trunk with the remote transmitter without triggering the alarm. The alarm will sound if the trunk lock is forced, or the trunk is opened with the trunk release lever or the emergency trunk opener.

The security system will not set if the hood, trunk, or any door is not fully closed. If the system will not set, check the door and trunk open indicators on the instrument panel (see page ) to see if the doors and trunk are fully closed. Since it is not part of the monitor display, manually check the hood.

60

CONTINUED

257

2011 Accord Sedan10/06/18 16:15:18 31TA5630_263

Security System

Use the remote transmitter NOTE: to quickly check that the hood, the trunk, and all doors are closed. Push the lock button twice within 5
seconds. There should be an audible confirmation beep.

Do not attempt to alter this system or add other devices to it.

258

2011 Accord Sedan10/06/18 16:15:28 31TA5630_264

EX-LandEX-LV6withoutnavigation system Compass Operation Compass operation can be affected by driving near power lines or stations, across bridges, through tunnels, over railroad crossings, past large vehicles, or driving near large objects that can cause a magnetic disturbance. It can also be affected by accessories such as antennas and roof racks that are mounted by magnets.

When you turn the ignition switch to the ON (II) position, the compass is self-calibrating, then the compass display is shown in the display.

Compass

Compass Calibration

COMPASS SETTING MENU ITEMS

COMPASS

U.S. model is shown.

The compass may need to be manually calibrated after exposure to a strong magnetic field. If the compass seems to be continually showing the wrong direction and is not self-calibrating, or the compass display is blinking with the CAL indicator on, do the following.

Do this procedure in an open

NOTE: area, away from buildings, power lines, and other vehicles.

1.

Turn the ignition switch to the ON (II) position.

2.

Press and hold the MENU button for about 5 seconds until you hear a beep. The display shows you the compass setting menu items.

CONTINUED

259

2011 Accord Sedan10/06/18 16:15:36 31TA5630_265

Compass

5.

Press the selector knob (ENTER). The compass display is blinking and the CAL indicator is shown.

6.

Drive the vehicle slowly in two complete circles.

When the calibration is successfully completed, the CAL indicator goes off and the compass display will stop blinking and show an actual heading.

The audio system is not related to the compass system. Even if the compass system is calibrating, the display returns to the normal display which you last selected.

3.

Turn the selector knob to select ‘‘CALIBRATION.’’

4.

Press the selector knob (ENTER) to enter your selection. The display shows you ‘‘PUSH CAL START.’’ While setting the compass, pressing the RETURN button will go back to the previous display. Pressing the MENU button will cancel the compass setting mode.

260

2011 Accord Sedan10/06/18 16:15:46 31TA5630_266

Compass Zone Selection In most areas, there is a variation between magnetic north and true north. Zone selection is required so the compass can compensate for this variation. To check and select the zone, do this:

1.

Turn the ignition switch to the ON (II) position.

2.

3.

Press and hold the MENU button for about 5 seconds until you hear a beep. The display shows you the compass setting menu items.

4.

Turn the selector knob to select ‘‘ZONE.’’ Press the selector knob (ENTER) to enter your selection. The display shows you the currently selected zone number.

262

Find the zone for your area on the map (see page ). If the correct zone is not shown, turn the selector knob to cycle the zone lists up or down. If necessary, press the RETURN button to return to the previous display. Pressing the MENU button will cancel the compass setting mode.

Compass

ZONE NUMBER

5.

Once the correct zone is displayed, press the selector knob. The display then returns to normal.

CONTINUED

261

2011 Accord Sedan10/06/18 16:15:50 31TA5630_267

Compass

The audio system is not related to the compass system. Even if the compass system is in the zone setting mode, the display returns to the normal display which you last selected.

Zone Map

262

2011 Accord Sedan10/06/18 16:15:58 31TA5630_268

Cruise control allows you to maintain a set speed above 25 mph (40 km/h) without keeping your foot on the accelerator pedal. It should be used for cruising on straight, open highways. It is not recommended for city driving, winding roads, slippery roads, heavy rain, or bad weather.

Improper use of the cruise control can lead to a crash.

Use the cruise control only when traveling on open highways in good weather.

Using the Cruise Control

CRUISE BUTTON

RES/ACCEL BUTTON

CANCEL BUTTON

SET/DECEL BUTTON

1.

Push in the CRUISE button on the steering wheel. The CRUISE MAIN indicator on the instrument panel comes on. The cruise control system can be left on, even when it is not in use.

2.

Accelerate to the desired cruising speed above 25 mph (40 km/h).

Cruise Control

3.

Press and release the SET/ DECEL button on the steering wheel. The CRUISE CONTROL indicator on the instrument panel comes on to show the system is now activated.

CONTINUED

263

2011 Accord Sedan10/06/18 16:16:06 31TA5630_269

Cruise Control

Cruise control may not hold the set speed when you are going up and down hills. If your vehicle speed increases going down a hill, use the brakes to slow down. This will cancel the cruise control. To resume the set speed, press the RES/ACCEL button. The CRUISE CONTROL indicator on the instrument panel will come back on.

264

Changing the Set Speed You can increase the set cruising speed in any of these ways:

Press and hold the RES/ACCEL button. When you reach the desired cruising speed, release the button. Push on the accelerator pedal. Accelerate to the desired cruising speed, then press the SET/ DECEL button. To increase the speed in very small amounts, tap the RES/ ACCEL button. Each time you do this, your vehicle will speed up about 1 mph (1.6 km/h).

You can decrease the set cruising speed in any of these ways:

If you need to decrease your NOTE: speed quickly, use the brakes as you normally would.

Press and hold the SET/DECEL button. Release the button when you reach the desired speed. To slow down in very small amounts, tap the SET/DECEL button repeatedly. Each time you do this, your vehicle will slow down about 1 mph (1.6 km/h). Tap the brake or clutch pedal lightly with your foot. The CRUISE CONTROL indicator on the instrument panel will go out. When the vehicle slows to the desired speed, press the SET/ DECEL button.

2011 Accord Sedan10/06/18 16:16:13 31TA5630_270

Even with the cruise control turned on, you can still use the accelerator pedal to speed up for passing. After completing the pass, take your foot off the accelerator pedal. The vehicle will return to the set cruising speed.

Resting your foot on the brake or clutch pedal causes the cruise control to cancel.

Canceling Cruise Control You can cancel cruise control in any of these ways:

Tap the brake or clutch pedal. Push the CANCEL button on the steering wheel. Push the CRUISE button on the steering wheel.

Cruise Control

Resuming the Set Speed When you push the CANCEL button, or tap the brake or clutch pedal, the system will remember the previously set cruising speed. To return to that speed, accelerate to above 25 mph (40 km/h), and then press and release the RES/ACCEL button. The CRUISE CONTROL indicator comes on. The vehicle will accelerate to the same cruising speed as before.

Pressing the CRUISE button turns the system completely off and erases the previous cruising speed.

265

2011 Accord Sedan10/06/18 16:16:19 31TA5630_271

HomeLink Universal Transceiver

EX-LV6
The HomeLink universal transceiver built into your vehicle can be programmed to operate up to three remotely controlled devices around your home, such as garage doors, lighting, or home security systems.

General Information Before programming your HomeLink to operate a garage door opener, confirm that the opener has an external entrapment protection system, such as an ‘‘electronic eye,’’ or other safety and reverse stop features.

If your garage door was manufactured before April 1, 1982, you may not be able to program HomeLink to operate it. These units do not have safety features that cause the motor to stop and reverse it if an obstacle is detected during closing, increasing the risk of injury. Do not use HomeLink with any garage door opener that lacks safety stop and reverse features.

Units manufactured between April 1, 1982 and January 1, 1993 may be equipped with safety stop and reverse features. If your unit does not have an external entrapment protection system, an easy test to confirm the function and performance of the safety stop and reverse feature is to lay a 2
under the closing door. The door should stop and reverse upon contacting the piece of wood. As an additional safety feature, garage door openers manufactured after January 1, 1993 are required to have external entrapment protection systems, such as an electronic eye, which detect an object obstructing the door.

×

266

2011 Accord Sedan10/06/18 16:16:28 31TA5630_272

Important Safety Precautions Refer to the safety information that came with your garage door opener to test that the safety features are functioning properly. If you do not have this information, contact the manufacturer of the equipment. Before programming HomeLink to a garage door or gate opener, make sure that people and objects are out of the way of the device to prevent potential injury or damage. When programming a garage door opener, park just outside the garage.

HomeLink Universal Transceiver

−

If you just

Training HomeLink Beforeyoubegin received your vehicle and have not trained any of the buttons in HomeLink before, you should erase any previously learned codes before training the first button. To do this, press and hold the two outside buttons on the HomeLink transceiver for about 10 20 seconds, − until the red indicator flashes. Release the buttons, then proceed to step 1.

CONTINUED

267

2011 Accord Sedan10/06/18 16:16:40 31TA5630_273

HomeLink Universal Transceiver

If you are training the second or third buttons, go directly to step 1.

268

2011 Accord Sedan10/06/18 16:16:45 31TA5630_274

HomeLink is a registered trademark of Johnson Controls, Inc.

HomeLink Universal Transceiver

AsrequiredbytheFCC: ThisdevicecomplieswithPart15ofthe FCCrules.Operationissubjecttothe followingtwoconditions:(1)Thisdevice maynotcauseharmfulinterference,and (2)thisdevicemustacceptany interferencereceived,including interferencethatmaycauseundesired operation.

Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser’s authoritytooperatetheequipment.

ThisdevicecomplieswithIndustry CanadaStandardRSS-210. Operationissubjecttothefollowingtwo conditions:(1)thisdevicemaynotcause interference,and(2)thisdevicemust acceptanyinterferencethatmaycause undesiredoperationofthedevice.

269

2011 Accord Sedan10/06/18 16:16:53 31TA5630_275

Bluetooth HandsFreeLink

HandsFreeLink (HFL)

Ifequipped Bluetooth allows you to place and receive phone calls using voice commands, without handling your cell phone.

To use HFL, you need a Bluetooth- compatible cell phone. For a list of compatible phones, pairing procedures, and special feature capabilities:

In the U.S., visit handsfreelink.honda.com or call (888) 528-7876.

In Canada, visit or call (888) 528-7876.

www.handsfreelink.ca,

270

HFL TALK BUTTON

HFL TALK BUTTON

Using HFL HFLButtons

NAVI VOICE CONTROL BUTTONS

HFL BACK BUTTON

On models with navigation system

HFL BACK BUTTON

On models without navigation system

HFL Talk button release to give a command or answer a call.

Press and

−

−

HFL Back button release to end a call, go back to the previous command, or cancel the command.

Press and

2011 Accord Sedan10/06/18 16:17:01 31TA5630_276

VoiceControlTips

MICROPHONE

Air or wind noise from the dashboard and side vents, windows and moonroof may interfere with the microphone. Adjust or close them as necessary.

Press and release the HFL Talk button each time you want to make a command. After the beep, speak in a clear, natural tone. Try to reduce all background noise. If the microphone picks up voices other than yours, commands may be misinterpreted.

Bluetooth HandsFreeLink

＃＃＃＃

Many commands can be spoken together. For example, you can say ‘‘Call 123-456- ’’ or ‘‘Dial Peter.’’ When HFL is in use, navigation voice commands cannot be recognized. To change the volume level of HFL, use the audio system volume knob or the steering wheel volume controls.

CONTINUED

271

2011 Accord Sedan10/06/18 16:17:10 31TA5630_277

Bluetooth HandsFreeLink

HelpFeatures

To hear general HFL information, including help on pairing a phone or setting up the system, say ‘‘Tutorial.’’ For help at any time, including a list of available commands, say ‘‘Hands free help.’’

Information Display

BLUETOOTH INDICATOR

PHONE NUMBER

On models without navigation system

When there is an incoming call, or HFL is in use, ‘‘HANDSFREELINK’’ will appear on the display.

’’ indicator will be displayed on

‘‘ the audio display when a phone is linked.

BLUETOOTH INDICATOR

U.S. model with navigation system is shown.

Onmodelswithnavigationsystem A notification that there is an incoming call, or HFL is in use, will appear on the navigation screen when the audio system is on.

272

2011 Accord Sedan10/06/18 16:17:17 31TA5630_278

Bluetooth HandsFreeLink

How to Use HFL

The ignition switch must be in the ACCESSORY (I) or ON (II) position.

‘‘Pair’’

‘‘Edit’’

Pair a phone to the system

(See page 276)

Edit the name of a paired phone (See page 277)

‘‘Phone Setup’’

‘‘Delete’’

Delete a paired phone from the system (See page 277)

Press HFL Talk button

‘‘List’’

‘‘Status’’

‘‘Next Phone’’

Hear a list of all phones paired to the system Hear which paired phone is currently linked to the system (See page 278) Search for another previously paired phone to link to

(See page 277)

(See page 278)

‘‘Set Pairing Code’’

Set the pairing code to a ‘‘Fixed’’ or ‘‘Random’’ number (See page 278)

‘‘Call’’ or ‘‘Dial’’

‘‘123-456-

＃＃＃＃

’’

Enter desired phone number (See page 279)

‘‘Jim Smith’’

Once a phonebook entry is stored, you can say a name here. (See page 279)

Press and release the HFL Talk button each time you give a command.

CONTINUED 273

2011 Accord Sedan10/06/18 16:17:22 31TA5630_279

Bluetooth HandsFreeLink

‘‘Redial’’

Redial the last number called

(See page 280)

‘‘Transfer’’

Transfer a call from HFL to your phone, or from your phone to HFL (See page 283)

‘‘Mute’’

‘‘Send’’

Mute your voice to the person at the other end of the call (See page 284)

Send numbers or names during a call

(See page 284)

Press HFL Talk button

‘‘Store’’

‘‘Edit’’

Store a phonebook entry (See page 285)

Edit the number of an existing phonebook entry

(See page 285)

‘‘Phonebook’’

‘‘Delete’’

Delete a phonebook entry (See page 286)

‘‘Receive Contact’’

‘‘List’’

If your phone supports this function, use this to transfer contacts from your phone to HFL (See page 286)

Hear a list of all stored phonebook entries

(See page 286)

Press and release the HFL Talk button each time you give a command.

274

2011 Accord Sedan10/06/18 16:17:28 31TA5630_280

Bluetooth HandsFreeLink

‘‘System Set up’’

Press HFL Talk button

‘‘Security’’

Apply a security passcode to the system that must be input at each key cycle to access the system (See page 291)

‘‘Change Passcode’’

Change your security passcode (See page 292)

‘‘Call Notification’’

‘‘Auto Transfer’’

Set how you would like to be notified of an incoming call (See page 292)

Set calls to automatically transfer from your phone to HFL when you enter the vehicle

(See page 292)

‘‘Clear’’

Clear the system of all paired phones, phonebook entries and security passcode (See page 293)

‘‘Change Language’’

Change language from English to French (See page 293) ＊

‘‘Tutorial’’

Hear a tutorial for general rules on using the system (See page 272)

‘‘Hands Free Help’’

Hear a list of available commands and additional information describing each command (See page 272)

Press and release the HFL Talk button each time you give a command. : Canadian models

＊

CONTINUED 275

2011 Accord Sedan10/06/18 16:17:37 31TA5630_281

Bluetooth HandsFreeLink

To use HFL, you need to pair your Bluetooth-compatible cell phone to the system.

Phone Setup This command group is available for paired cell phones.

Phonepairingtips

You cannot pair your phone while the vehicle is moving. Your phone must be in discovery or search mode to pair. Refer to your phone’s manual. Up to six phones can be paired. Your phone’s battery may drain faster when it is paired to HFL. If after three minutes your phone is not ready to pair or a phone is not found, the system will time out and return to idle.

276

Topairacellphone: 1.

Press and release the HFL Talk button. If you are pairing a phone for the first time, HFL will give you information about the pairing process. If it is not the first phone you are pairing, say ‘‘ setup Pair

Phone .’’

’’ and say ‘‘

2.

Follow the HFL prompts and put your phone in discovery or search mode. HFL will give you a 4-digit pairing code and begin searching for your phone.

3.

When your phone finds a Bluetooth device, select HFL from the options and enter the 4-digit code from the previous step.

4.

Follow the HFL prompts and name the newly paired phone.

2011 Accord Sedan10/06/18 16:17:48 31TA5630_282

Torenameapairedphone: Press and release the HFL Talk button before a command.

Todeleteapairedphone: Press and release the HFL Talk button before a command.

1.

Say ‘‘

Phone setup

.’’

2.

Say ‘‘

Edit

’’ after the prompts.

3.

If there is more than one phone paired to the system, HFL will ask you which phone’s name you want to change. Follow the HFL prompts and rename the phone.

1.

2.

3.

Say ‘‘

Phone setup

.’’

Say ‘‘

Delete

’’ after the prompts.

HFL will ask you which phone you want to delete. Follow the HFL prompts to continue with the deletion.

Bluetooth HandsFreeLink

Tohearthenamesofallpaired phones: Press and release the HFL Talk button before a command.

1.

Say ‘‘

Phone setup

.’’

2.

Say ‘‘

List

’’ after the prompts.

3.

HFL will read out all the paired phone’s names.

CONTINUED

277

2011 Accord Sedan10/06/18 16:18:00 31TA5630_283

Bluetooth HandsFreeLink

Tohearwhichpairedphoneis currentlylinked: Press and release the HFL Talk button before a command.

Tochangefromthecurrentlylinked phonetoanotherpairedphone: Press and release the HFL Talk button before a command.

1.

2.

3.

Say ‘‘

Phone setup

.’’

Say ‘‘

Status

’’ after the prompts.

HFL will tell you which phone is linked to the system.

1.

2.

3.

4.

Say ‘‘

Phone setup

.’’

Next phone

’’ after the

Say ‘‘ prompts.

HFL disconnects the linked phone and searches for another paired phone.

Once another phone is found, it is linked to the system. HFL will inform you which phone is now linked.

If no other phones are found or paired, HFL will inform you that the original phone is linked again.

278

Tochangethepairingcodesetting: Press and release the HFL Talk button before a command.

1.

2.

3.

Say ‘‘

Phone setup

.’’

Set pairing code

’’ after the

Say ‘‘ prompts.

If you want HFL to create a random code each time you pair a phone, say ‘‘ .’’ If you want to choose your own 4-digit code to be used each time, say ‘‘ and follow the HFL prompts.

Random

Fixed ’’

2011 Accord Sedan10/06/18 16:18:11 31TA5630_284

Making a Call You can make calls using any phone number or a name in the HFL phonebook. You can also redial the last number called.

Bluetooth is the wireless technology that links your phone to HFL. HFL uses a Class 2 Bluetooth, which means the maximum range between your phone and vehicle is 30 feet (10
meters).

During a call, HFL allows you to talk up to 30 minutes after you remove the key from the ignition switch. However, this may weaken the vehicle’s battery.

Bluetooth HandsFreeLink

Tomakeacallusingaphone number: Press and release the HFL Talk button before a command.

Tomakeacallusinganameinthe HFLphonebook: Press and release the HFL Talk button before a command.

1.

Say ‘‘

Call

’’ or ‘‘

Dial

.’’

1.

Say ‘‘

Call

’’ or ‘‘

Dial

.’’

2.

Follow the HFL prompts and say the phone number you want to dial.

3.

Follow the HFL prompts to confirm the number and say Call ‘‘

’’ or ‘‘

Dial

.’’

Once connected, you will hear the person you called through the audio speakers.

2.

3.

Follow the HFL prompts and say the name stored in the HFL phonebook that you want to call.

Follow the HFL prompts to confirm the name and make the call.

CONTINUED

279

2011 Accord Sedan10/06/18 16:18:20 31TA5630_285

Bluetooth HandsFreeLink

Toredialthelastnumbercalledby HFL: Press and release the HFL Talk button and say ‘‘

Redial

.’’

Tomakeacallfromanimported phonebook:

3.

Select a phonebook you want to choose a phone number from.

Onmodelswithnavigationsystem 1.

Press the INFO button, then select Cellular Phone ‘‘

.’’

Select ‘‘ Phonebook

.’’

Search Imported

2.

280

If the phonebook you select is PIN- protected, you will need to enter the PIN to access it. See page more information.

289

for

2011 Accord Sedan10/06/18 16:18:27 31TA5630_286

Push up the interface selector to show a list.

To search for a specific name in the phonebook, enter the keyword for either the first or last name.

To display all names in the List phonebook, select the ‘‘

’’ option.

4.

5.

Select the name. All the phone numbers stored for that name will be listed.

Select the phone number, and push the interface selector to the right.

Bluetooth HandsFreeLink

Store in

Selecting ‘‘ HandsFreeLink number will be stored in HFL, so that you can call it using HFL’s name tag by voice.

,’’ the phone

CONTINUED

281

2011 Accord Sedan10/06/18 16:18:36 31TA5630_287

Bluetooth HandsFreeLink

Tomakeacallusingthenavigation display(onmodelswithnavigation system):

1.

Press the INFO button, and the INFO screen will be shown.

2.

From the INFO screen, select ‘‘Cellular Phone,’’ then select ‘‘Dial.’’

3.

The navigation display will change as shown above. Enter a call number.

4.

To make a call, press the selector on the interface dial to the right.

5.

To end the call, press the HFL Back button.

282

2011 Accord Sedan10/06/18 16:18:43 31TA5630_288

Receiving a Call When you receive a call, an incoming call notification (if activated) will play and interrupt the audio system if it is on.

CallWaiting If your phone has Call Waiting, press and release the HFL Talk button to put the original call on hold and answer the incoming call.

Press the HFL Talk button to answer the call, or the HFL Back button to hang up.

To return to the original call, press the HFL Talk button again. If you don’t want to answer the incoming call, disregard it and continue with your original call. If you want to hang up the original call and answer the new call, press the HFL Back button.

Bluetooth HandsFreeLink

Transferring a Call You can transfer a call from HFL to your phone, or from your phone to HFL.

Press and release the HFL Talk button and say ‘‘

Transfer

.’’

283

2011 Accord Sedan10/06/18 16:18:53 31TA5630_289

Bluetooth HandsFreeLink

Muting a Call You can mute your voice to the person you are talking to during a call.

To mute your voice during a call, press and release the HFL Talk button and say ‘‘

Mute

.’’

To unmute your voice, press and release the HFL Talk button and say Mute ‘‘

’’ again.

284

Phonebook You can store up to 50 names with their associated numbers in HFL. The numbers you store can be not only phone numbers but other types, such as account numbers or passwords, which can be sent during a menu-driven call.

Send Numbers or Names During a Call HFL allows you to send numbers or names during a call. This is useful when you call a menu-driven phone system.

Tosendanameornumberduringa call: Press and release the HFL Talk button before a command.

1.

Say ‘‘

Send

.’’

2.

Follow the HFL prompts and say the name or number you want to send.

3.

Follow the HFL prompts to send the tones and continue the call.

To send a pound (

NOTE: ‘‘pound.’’ To send a star (*), say ‘‘star.’’

), say

＃

2011 Accord Sedan10/06/18 16:19:06 31TA5630_290

Tostoreaphonebookentry: Press and release the HFL Talk button before a command.

1.

Say ‘‘

Phonebook

.’’

2.

3.

Say ‘‘

Store

’’ after the prompts.

Say a name you want to list as your phonebook entry.

4.

Say the number you want to store for the name entry.

5.

Follow the HFL prompts and say Enter ‘‘

’’ to store the entry.

NOTE:

Avoid using duplicate name entries. Avoid using ‘‘home’’ as a name entry. It is easier for HFL to recognize a multisyllabic or longer name. For example, use ‘‘Peter’’ instead of ‘‘Pete,’’ or ‘‘John Smith’’ instead of ‘‘John.’’

Bluetooth HandsFreeLink

Toeditthenumberstoredinaname: Press and release the HFL Talk button before a command.

1.

Say ‘‘

Phonebook

.’’

2.

Say ‘‘

Edit

’’ after the prompts.

3.

Follow the HFL prompts and say the name entry you want to edit.

4.

When asked, say the new number for that name.

5.

Follow the HFL prompts to complete the edit.

CONTINUED

285

2011 Accord Sedan10/06/18 16:19:19 31TA5630_291

Bluetooth HandsFreeLink

Todeleteaname: Press and release the HFL Talk button before a command.

Tolistallnamesinthephonebook: Press and release the HFL Talk button before a command.

1.

Say ‘‘

Phonebook

.’’

1.

Say ‘‘

Phonebook

.’’

2.

3.

Say ‘‘

Delete

’’ after the prompts.

Say the name you want to delete and follow the HFL prompts to complete the deletion.

2.

Say ‘‘

List

’’ after the prompts.

3.

HFL begins reading the names in the order they were stored.

4.

If you hear a name you want to call, immediately press the HFL Talk button and say ‘‘

Call

.’’

Tostoreaspecificphonenumber fromyourcellphonedirectlytothe HFLphonebook(availableonsome phones): Press and release the HFL Talk button before a command.

1.

Say ‘‘

Phonebook

.’’

2.

3.

4.

Receive contact

Say ‘‘ prompts.

’’ after the

Follow the HFL prompts, select a number from your cell phone, and send it to HFL.

Follow the HFL prompts and name the number, or say Discard ‘‘ you want to store.

’’ if it is not the number

5.