could be a problem with the brake system. For more information, see page
367
Side Airbag Off Indicator
U.S.
Canada
This indicator comes on briefly when you turn the ignition switch to the ON (II) position. If it comes on at any other time, it indicates that the passenger’s side airbag has automatically shut off. For more information, see page
30
57
2010 Accord Sedan09/05/18 18:18:06 31TA5620 0063
Instrument Panel Indicators
Anti-lock Brake System (ABS) Indicator
This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position. If it comes on at any other time, there is a problem with the ABS. If this happens, have your vehicle checked at a dealer. With this indicator on, your vehicle still has normal braking ability but no anti-lock function. For more information, see page
287
Vehicle Stability Assist (VSA) System Indicator
This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position.
If it comes on and stays on at any
other time, or if it does not come on
when you turn the ignition switch to
the ON (II) position, there is a
problem with the VSA system. Take
your vehicle to a dealer to have it
checked. Without VSA, your vehicle
still has normal driving ability, but
will not have VSA traction and
stability enhancement. See page
for more information on the
289
VSA system.
VSA Activation Indicator
This indicator has three functions:
1.
2.
3.
It comes on as a reminder that you have turned off the vehicle stability assist (VSA) system.
It flashes when VSA is active (see page
289
).
It comes on along with the VSA system indicator if there is a problem with the VSA system.
This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position. For more information, see page
289
58
2010 Accord Sedan09/05/18 18:18:18 31TA5620 0064
Low Tire Pressure Indicator
This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position. If it comes on while driving, it indicates that one or more of your vehicle’s tires are significantly low on pressure.
If this happens, pull to the side of the road when it is safe, check which tire has lost the pressure, and determine the cause. If it is because of a flat tire, replace the flat tire with the compact spare (see page ), and have the flat tire repaired as soon as possible. If two or more tires are underinflated, call a professional towing service (see page information, see page
). For more
291
353
375
Instrument Panel Indicators
Fuel Economy Indicator
V6models While the engine is operating in its most economical range, this indicator may come on and stay on.
Tire Pressure Monitoring System (TPMS) Indicator This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position.
If this indicator comes on and stays on at any other time, or if it does not come on when you turn the ignition switch to the ON (II) position, there is a problem with the TPMS. With this indicator on, the low tire pressure indicator will not come on when a tire loses pressure. Take the vehicle to your dealer to have the system checked.
59
2010 Accord Sedan09/05/18 18:18:29 31TA5620 0065
Instrument Panel Indicators
Turn Signal and Hazard Warning Indicators
The left or right turn signal indicator blinks when you signal a lane change or turn. If an indicator does not blink or blinks rapidly, it usually means one of the turn signal bulbs is burned out (see pages ). and Replace the bulb as soon as possible, since other drivers cannot see that you are signaling.
328
330
When you press the hazard warning button, both turn signal indicators and all turn signals on the outside of the vehicle flash.
60
Lights On Indicator
Door and Trunk Open Indicator
or
This indicator reminds you that the exterior lights are on. It comes on when the light switch is in either the position. If you turn the
ignition switch to the ACCESSORY (I) or the LOCK (0) position without turning off the light switch, this indicator will remain on. A reminder chime will also sound when you open the driver’s door.
EX-LandEX-LV6
This indicator will also come on
when the light switch is in AUTO
and the lights turn on automatically.
DRIVER’S DOOR OPEN INDICATOR
TRUNK OPEN INDICATOR
The appropriate indicator comes on if the trunk or any door is not closed tightly.
All the indicators come on for a few seconds when you turn the ignition switch to the ON (II) position.
2010 Accord Sedan09/05/18 18:18:42 31TA5620 0066
Low Fuel Indicator
Security System Indicator
High Beam Indicator
Instrument Panel Indicators
This indicator comes on as a reminder that you must refuel soon. When the indicator comes on, there are about 2.8 U.S. gal (10.5 ) of fuel remaining in the tank.
When the needle reaches E, there is a very small amount of fuel in the tank.
SECURITY SYSTEM INDICATOR
This indicator comes on with the high beam headlights. For more information, see page
69
This indicator also comes on with reduced brightness when the daytime running lights (DRL) are on (see page
71
).
Ifequipped
This indicator comes on when the
security system is set. See page
217
for more information on the
security system.
Daytime Running Lights Indicator
If this indicator comes on when you turn the ignition switch to the ON (II) position and release the parking brake, it means there is a problem with the DRL. There may also be a problem with the high beam headlights. Have your vehicle checked by your dealer.
61
2010 Accord Sedan09/05/18 18:19:01 31TA5620 0067
Instrument Panel Indicators
Maintenance Minder Indicator
This indicator comes on for a few
seconds when you turn the ignition
switch to the ON (II) position. It
reminds you that it is time to take
your vehicle in for scheduled
maintenance. The maintenance main
items and sub items will be displayed
in the information display. See page
303
maintenance minder.
for more information on the
This indicator goes off when your dealer resets it after completing the required maintenance service.
Immobilizer System Indicator
This indicator comes on briefly when you turn the ignition switch to the ON (II) position. It will then go off if you have inserted a properly coded ignition key. If it is not a properly coded key, the indicator will blink, and the engine’s fuel system will be disabled (see page
77
).
Washer Level Indicator
Canadianmodelsonly This indicator comes on when the washer fluid level is low. Add washer fluid when you see this indicator (see page
318
).
Cruise Control Main Indicator
This indicator comes on when you turn on the cruise control system by pressing the CRUISE button (see page
223
).
Cruise Control Indicator
This indicator comes on when you
set the cruise control. See page
223
cruise control.
for information on operating the
Fog Light Indicator
Ifequipped This indicator comes on when you turn on the fog lights. For more information, see page
72
62
2010 Accord Sedan09/05/18 18:19:09 31TA5620 0068
TACHOMETER
SPEEDOMETER
TEMPERATURE GAUGE
FUEL GAUGE
OUTSIDE TEMPERATURE INDICATOR
*
TRIP METER
SELECT/RESET KNOB
ODOMETER/CHECK FUEL CAP MESSAGE
U.S. model is shown.
* If equipped
INFORMATION DISPLAY
Gauges
63
2010 Accord Sedan09/05/18 18:19:16 31TA5620 0069
Gauges
INFORMATION DISPLAY
ODOMETER
TRIP METER A
ENGINE OIL LIFE
OUTSIDE TEMPERATURE INDICATOR
TRIP METER B
: Press the select/reset knob.
U.S. model with outside temperature indicator is shown.
Information Display The information display shows the odometer, trip meter, engine oil life, outside temperature (if equipped), and maintenance item code(s).
To switch the display, press and release the select/reset knob repeatedly. When you turn the ignition switch to the ON (II) position, your last selection is displayed.
64
Odometer The odometer shows the total distance your vehicle has been driven. It measures miles in U.S. models and kilometers in Canadian models. It is illegal under U.S. federal law and Canadian provincial/ territorial regulations to disconnect, reset, or alter the odometer with the intent to change the number of miles or kilometers indicated.
2010 Accord Sedan09/05/18 18:19:31 31TA5620 0070
Outside Temperature Indicator Ifequipped This indicator displays the outside temperature in Fahrenheit (U.S. models) or Celsius (Canadian models). To see the outside temperature, press and release the select/reset knob until the temperature is displayed.
The temperature sensor is in the front bumper. Therefore, the temperature reading can be affected by heat reflection from the road surface, engine heat, and the exhaust from surrounding traffic. This can cause an incorrect temperature reading when your speed is under 19 mph (30 km/h).
The sensor delays the display update until it reaches the correct outside temperature. This may take several minutes.
If the outside temperature is
incorrectly displayed, you can adjust it up to 3°C ± in Canadian models) warmer or cooler.
5°F in U.S. models (
±
The temperature must be
NOTE: stabilized before doing this procedure.
Select the outside temperature display, then press and hold the select/reset knob for 10 seconds. The following sequence will appear for 1 second each: 0, 1, 2, 3, 4, 5, 5, − 1, 0 (U.S.) or 0, 1, 2, − − − − 3,
4, 2, − − −
1, 0 (Canada).
3,
3,
2,
When the temperature reaches the desired value, release the select/ reset knob. You should see the new outside temperature displayed.
In certain weather conditions, temperature readings near freezing (32°F, 0°C) could mean that ice is forming on the road surface.
Gauges
Trip Meter The trip meter shows the number of miles (U.S.) or kilometers (Canada) driven since you last reset it.
There are two trip meters: Trip A and Trip B. Switch between these displays by pressing the select/reset knob repeatedly.
Each trip meter works independently, so you can keep track of two different distances.
When you turn the ignition switch to the ON (II) position, your last selection is displayed.
To reset a trip meter, display it, and then press and hold the select/reset knob until the number resets to ‘‘0.0’’.
65
2010 Accord Sedan09/05/18 18:19:42 31TA5620 0071
Gauges
Temperature Gauge This shows the temperature of the engine’s coolant. During normal operation, the pointer should rise from the bottom mark to about the middle of the gauge. In severe driving conditions, such as very hot weather or a long period of uphill driving, the pointer may rise to the upper zone. If it reaches the red (hot) mark, pull safely to the side of the road. Turn to page for instructions and precautions on checking the engine cooling system.
363
Fuel Gauge This shows how much fuel you have. It may show slightly more or less than the actual amount. The needle returns to the bottom after you turn off the ignition.
Avoid driving with an extremely low f uel level. Running out of f uel could cause the engine to misf ire, damaging the catalytic converter.
Check Fuel Cap Message If your fuel fill cap is loose or missing, a ‘‘CHECK FUEL CAP’’ message appears on the information display after you start the engine. For more information, see page
258
Maintenance Minder The information display in the instrument panel shows you the engine oil life and maintenance service items when the ignition switch is in the ON (II) position. This information helps to keep you aware of the periodic maintenance your vehicle needs for continued trouble- free driving. Refer to page more information.
303
for
66
2010 Accord Sedan09/05/18 18:19:49 31TA5620 0072
HEADLIGHT/TURN SIGNALS/ FOG LIGHTS
(P.69, 72)
*
REMOTE AUDIO CONTROLS (P.211)
VEHICLE STABILITY ASSIST (VSA) SYSTEM OFF SWITCH (P.290)
BLUETOOTH HANDSFREELINK VOICE CONTROL BUTTONS (P.230)
*
NAVIGATION SYSTEM VOICE CONTROL BUTTONS
*
Controls Near the Steering Wheel
INSTRUMENT PANEL BRIGHTNESS
(P.72)
WINDSHIELD WIPERS/ WASHERS
(P.68)
PASSENGER AIRBAG OFF INDICATOR (P.30)
HAZARD WARNING BUTTON (P.73) INTERFACE DIAL * (P.174)
HORN
*
CRUISE CONTROL BUTTONS (P.223)
STEERING WHEEL ADJUSTMENTS
(P.75)
REAR WINDOW DEFOGGER/ HEATED MIRROR BUTTON * (P.74, 102)
SEAT HEATER SWITCHES (P.100)
*
* * *
1 : 2 : 3 :
To use the horn, press the center pad of the steering wheel. If equipped Only on vehicles equipped with navigation system, refer to the navigation system manual.
67
2010 Accord Sedan09/05/18 18:20:02 31TA5620 0073
Windshield Wipers and Washers
Push the right lever up or down to select a position.
MIST The wipers run at high speed until you release the lever.
−
OFF
−
The wipers are not activated.
−
INT The length of the wipe interval is varied automatically according to vehicle’s speed.
Vary the delay by turning the adjustment ring. If you turn it to the shortest delay ( position), the wipers change to low speed operation when the vehicle speed exceeds 12 mph (20 km/h).
Windshield Wipers
ADJUSTMENT RING
1. 2. 3. 4. 5. 6.
MIST OFF INT LO Low speed HI High speed Windshield washers
Intermittent
− − −
68
LO
−
The wipers run at low speed.
HI
−
The wipers run at high speed.
−
Pull the
Windshield Washer wiper control lever toward you, and hold it. The washers spray until you release the lever. The wipers run at low speed, then complete a few more sweeps after you release the lever.
2010 Accord Sedan09/05/18 18:20:13 31TA5620 0074
−
Turn Signal Push down on the left lever to signal a left turn and up to signal a right turn. To signal a lane change, push lightly on the lever and hold it. The lever will return to the center when you release it or complete a turn.
EX-L V6 model is shown.
1. 2. 3. 4. 5. 6. 7. 8. 9.
*
Turn signal Off Parking and indicator lights AUTO Headlights on High beams Flash high beams Fog lights off Fog lights on
*
*
−
Turning the switch to
’’ position turns on the
Headlights the ‘‘ parking lights, taillights, instrument panel lights, side-marker lights, and rear license plate lights.
Turning the switch to the ‘‘ position turns on the headlights.
’’
If you leave the lights on with the key removed from the ignition switch, you will hear a reminder chime when you open the driver’s door.
Turn Signals and Headlights
When the light switch is in either of these positions, the lights on indicator comes on as a reminder.
This indicator stays on if you leave the lights on and turn the ignition switch to the ACCESSORY (I) or LOCK (0) position.
−
High Beams To switch from low beams to high beams, push the left lever forward until you hear a click. The blue high beam indicator will come on (see page ). Pull it back to return to low beams. To flash the high beams, pull the lever back lightly, then release it. The high beams stay on as long as you hold the lever back.
61
*
If equipped
69
2010 Accord Sedan09/05/18 18:20:21 31TA5620 0075
Turn Signals and Headlights
Even with the automatic lighting feature turned on, we recommend that you turn on the lights manually when driving at night or in a dense fog, or when you enter dark areas such as long tunnels or parking facilities.
Do not leave the light switch in AUTO if you will not be driving the vehicle for an extended period (a week or more). You should also turn off the lights if you plan to leave the engine idling or off for a long time.
LIGHT SENSOR
The automatic lighting feature is controlled by a sensor located on top of the dashboard. Do not cover this sensor or spill liquids on it.
−
The automatic lighting
EX-LandEX-LV6
AUTO
feature turns on the headlights and
all other exterior lights, when it
senses low ambient light.
To turn on automatic lighting, turn the light switch to AUTO. The lights will come on automatically when the outside light level becomes low (at dusk, for example). The lights on indicator comes on as a reminder. The lights and indicator will turn off automatically when the system senses high ambient light.
The lights will remain on when you turn off the ignition switch. They will turn off automatically when you remove the key and open the driver’s door. To turn them on again, either turn the ignition switch to the ON (II) position or turn the light switch to the
position.
70
2010 Accord Sedan09/05/18 18:20:31 31TA5620 0076
Automatic Lighting Off Feature
This feature turns off the headlights,
all other exterior lights, and the
instrument panel lights within 15
seconds after you remove the key
and close the driver’s door.
If you turn the ignition switch to the
LOCK (0) position with the
headlight switch on, but do not open
the door, the lights turn off after 10
minutes (3 minutes, if the switch is
in the ‘‘AUTO’’ position).
’’ or ‘‘
The automatic lighting off feature activates if you leave the headlight switch in the ‘‘ position or if the lights are turned on by setting the switch in the ‘‘AUTO’’ position (if equipped), and you remove the key, then open and close the driver’s door.
’’
The lights will turn on again when you unlock or open the driver’s door. If you unlock the door, but do not open it within 15 seconds, the lights will go off. With the driver’s door open, you will hear a lights-on reminder chime.
Turn Signals and Headlights
position, the high beam
Daytime Running Lights With the headlight switch off or in the headlights and the high beam indicator come on with reduced brightness when you turn the ignition switch to the ON (II) position and release the parking brake. They remain on until you turn the ignition switch off, even if you set the parking brake.
The headlights revert to normal operation when you turn them on with the switch.
71
2010 Accord Sedan09/05/18 18:20:41 31TA5620 0077
Fog Lights, Instrument Panel Brightness
Fog Lights
Instrument Panel Brightness
You can use the fog lights only when the headlights are on low beam. With the light switch in the AUTO position (if equipped), you can also use the fog lights when the headlights turn on automatically. They will go off when the headlights turn off, or the daytime running lights are on.
EX-L V6 model is shown.
Ifequipped Turn the fog lights on and off by turning the switch next to the headlight switch.
72
SELECT/RESET KNOB
The select/reset knob on the instrument panel controls the brightness of the instrument panel lights. Turn the knob to adjust the brightness with the ignition switch in the ON (II) position and the parking lights on.
2010 Accord Sedan09/05/18 18:20:51 31TA5620 0078
Instrument Panel Brightness, Hazard Warning Button
The instrument panel will illuminate with reduced brightness when you unlock and open the driver’s door. The brightness will increase slightly when you insert the key in the ignition switch, then go to normal brightness when you turn the ignition switch to the ON (II) position.
If you do not insert the key in the ignition switch after opening the driver’s door, the illumination turns off about 30 seconds after you close the door.
If you insert the key but do not turn the ignition switch to the ON (II) position, the illumination turns off in about 10 seconds.
Hazard Warning Button
U.S. model is shown.
Push the button between the center vents to turn on the hazard warning lights (four-way flashers). This causes all four outside turn signals and both turn indicators in the instrument panel to flash. Use the hazard warning lights if you need to park in a dangerous area near heavy traffic, or if your vehicle is disabled.
73
BRIGHTNESS LEVEL
The level of brightness is shown on the information display while you adjust it. It goes out about 5 seconds after you finish adjusting.
To reduce glare at night, the instrument panel illumination dims when you turn the light switch to
or
. Turning the select/
reset knob to the right until you hear a beep will cancel the reduced brightness.
2010 Accord Sedan09/05/18 18:21:02 31TA5620 0079
Rear Window Defogger
U.S. LX, LX-P
Manual A/C type
Except U.S. LX, LX-P
Auto A/C type
The rear window defogger will clear fog, frost, and thin ice from the window. Push the defogger button to turn it on and off. The indicator in the button comes on to show the defogger is on. It also shuts off when you turn off the ignition switch. You have to turn the defogger on again when you restart the vehicle.
Onmodelswithautomaticair conditioningsystem The defogger will shut itself off within about 10 to 30 minutes according to the outside temperature (over 32°F, 0°C).
Make sure the rear window is clear and you have good visibility before starting to drive.
74
On models with navigation system
The defogger and antenna wires on the inside of the rear window can be accidentally damaged. When cleaning the glass, always wipe side to side.
ExceptU.S.LXandLX-P Pushing this button also turns the mirror heaters on or off. For more information, see page
102
2010 Accord Sedan09/07/08 21:35:01 31TA5620_080
Make any steering wheel adjustments before you start driving.
Adjusting the steering wheel position while driving may cause you to lose control of the vehicle and be seriously injured in a crash.
Adjust the steering wheel only when the vehicle is stopped.
1.
Push the lever under the steering column all the way down.
2.
Move the steering wheel up or down, and in or out, so it points toward your chest, not toward your face. Make sure you can see the instrument panel gauges and indicators.
Steering Wheel Adjustments
3.
Push the lever up to lock the steering wheel in position.
4.
Make sure you have securely locked the steering wheel in place by trying to move it up, down, in, and out.
75
2010 Accord Sedan09/05/18 18:21:18 31TA5620 0081
Keys and Locks
KEY NUMBER TAG
MASTER KEY WITH REMOTE TRANSMITTER
VALET KEY (Light Grey)
You should have received a key number tag with your keys. You will need this key number if you ever have to get a lost key replaced. Use only Honda-approved key blanks.
These keys contain electronic circuits that are activated by the immobilizer system. They will not work to start the engine if the circuits are damaged.
Protect the keys from direct sunlight, high temperature, and high humidity.
Do not drop the keys or set heavy objects on them.
Keep the keys away from liquids. If they get wet, dry them immediately with a soft cloth.
The valet key does not contain a battery. Do not try to take it apart.
The master key fits all the locks on your vehicle. The valet key works only in the ignition and the driver’s door lock. You can keep the trunk release handle, rear seat trunk access, and glove box locked when you leave your vehicle and the valet key at a parking facility.
76
2010 Accord Sedan09/05/18 18:21:28 31TA5620 0082
If the system repeatedly does not recognize the coding of your key, contact your dealer.
Do not attempt to alter this system or add other devices to it. Electrical problems could result that may make your vehicle inoperable.
If you lose your key and you cannot start the engine, contact your dealer.
Always take the ignition key with you whenever you leave the vehicle alone.
The immobilizer system protects your vehicle from theft. If an improperly coded key (or other device) is used, the engine’s fuel system is disabled.
When you turn the ignition switch to the ON (II) position, the immobilizer system indicator should come on briefly, then go off. If the indicator starts to blink, it means the system does not recognize the coding of the key. Turn the ignition switch to the LOCK (0) position, remove the key, reinsert it, and turn the ignition switch to the ON (II) position again.
The system may not recognize your key’s coding if another immobilizer key or other metal object (i.e. key chain) is near the ignition switch when you insert the key.
Immobilizer System
AsrequiredbytheFCC: ThisdevicecomplieswithPart15ofthe FCCrules.Operationissubjecttothe followingtwoconditions:(1)Thisdevice maynotcauseharmfulinterference,and (2)thisdevicemustacceptany interferencereceived,including interferencethatmaycauseundesired operation.
Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser’s authoritytooperatetheequipment.
ThisdevicecomplieswithIndustry CanadaStandardRSS-210. Operationissubjecttothefollowingtwo conditions:(1)thisdevicemaynotcause interference,and(2)thisdevicemust acceptanyinterferencethatmaycause undesiredoperationofthedevice.
77
2010 Accord Sedan09/07/08 21:36:07 31TA5620_083
Ignition Switch
The ignition switch has four positions: LOCK (0), ACCESSORY (I), ON (II), START (III)
−
You can insert or
LOCK (0) remove the key only in this position. To turn the key, push it in slightly. If your vehicle has an automatic transmission, the shift lever must also be in Park.
78
If the front wheels are turned, the anti-theft lock may make it difficult to turn the key. Firmly turn the steering wheel to the left or right as you turn the key.
−
You can
ACCESSORY (I) operate the audio system and the accessory power sockets in this position.
−
This is the normal key
ON (II) position when driving. Several of the indicators on the instrument panel come on as a test when you turn the ignition switch from the ACCESSORY (I) to the ON (II) position.
−
Use this position
START (III) only to start the engine. The switch returns to the ON (II) position when you let go of the key.
You will hear a reminder beeper if you leave the key in the ignition switch in the LOCK (0) or the ACCESSORY (I) position and open the driver’s door. Remove the key to turn off the beeper.
If your vehicle has an automatic transmission, the shift lever must be in Park before you can remove the key from the ignition switch.
Removing the key from the ignition switch while driving locks the steering. This can cause you to lose control of the vehicle.
Remove the key from the ignition switch only when parked.
2010 Accord Sedan09/05/18 18:21:50 31TA5620 0084
POWER DOOR LOCK MASTER SWITCH
Lock
Unlock
LOCK TAB
Lock
Unlock
RED INDICATOR
To lock all doors, push the front of the master door lock switch on either front door, pull the lock tab rearward on the driver’s door, or use the key on the outside lock on the driver’s door.
The lock tab on any passenger’s door locks and unlocks that door.
When the door is unlocked, you can see the red indicator on the lock tab above the inner door handle.
Pushing the rear of either master door lock switch will unlock all doors. Pushing forward the lock tab on the driver’s door unlocks only that door.
Door Locks
All doors can be locked from the outside by using the key in the driver’s door. To unlock only the driver’s door, insert the key, turn it clockwise, and release it. The remaining doors unlock when you turn the key a second time within a few seconds.
You can open or close the windows and the moonroof (if equipped) by using the key in the driver’s door (see page
105
).
To lock any passenger’s door when getting out of the vehicle, pull the lock tab rearward and close the door. To lock the driver’s door, remove the key from the ignition switch, pull the lock tab rearward or push the front of the master switch, then close the door.
CONTINUED
79
2010 Accord Sedan09/05/18 18:22:01 31TA5620 0085
Auto Door Locking/Unlocking Your vehicle has customizable settings for the doors to automatically lock and unlock. There are default settings for each of these features. You can turn off or change the settings for these features as described on the following pages.
When you customize the setting, make sure your vehicle is parked safely, the engine is off, and the parking brake is applied. Make all settings before you start driving.
Auto Door Locking The auto door locking feature has three possible settings:
The auto door locking is deactivated all the time.
The doors lock whenever you move the shift lever out of the Park (P) position (A/T vehicles).
The doors lock when the vehicle speed reaches 9 mph (15 km/h). This is the default setting.
Door Locks
LockoutPrevention If you forget and leave the key in the ignition switch, lockout prevention will not allow you to lock the driver’s door. With any door open and the key in the ignition switch, locking with the master door lock switch is disabled. If the driver’s door is closed, the lock tab on the driver’s door is not disabled. Pulling the driver’s lock tab rearward will lock all doors. If you try to lock an open driver’s door by pulling the lock tab rearward, the driver’s door lock tab pops out and unlocks the driver’s door.
80
2010 Accord Sedan09/05/18 18:22:14 31TA5620 0086
Door Locks
ToturnofftheAutoDoorLock modes:
3.
Push and hold the front of the master door lock switch on the driver’s door until you hear a click (after about 5 seconds).
ToprogramtheParkLockmode: Locksalldoorswhentheshiftleveris movedoutofthePark(P)position(A/T vehiclesonly).
4.
Release the switch, and within 5
seconds, turn the ignition switch
to the LOCK (0) position.
1.
Make sure the shift lever is in the Park (P) position (A/T vehicles).
2.
Turn the ignition switch to the ON (II) position, and open the driver’s door.
1.
Make sure the shift lever is in the Park (P) position.
2.
Turn the ignition switch to the ON (II) position, and make sure to close the driver’s door.
CONTINUED
81
2010 Accord Sedan09/05/18 18:22:25 31TA5620 0087
Door Locks
3.
Push and hold the front of the
master door lock switch on the
driver’s door. You will hear a click.
Keep holding the switch until you
hear another click (after about 5
seconds).
4.
Release the switch, and within 5
seconds, turn the ignition switch
to the LOCK (0) position.
ToprogramtheDriveLockmode: Locksalldoorswhenthevehicle’sspeed reachesabout9mph(15km/h).
1.
Make sure the shift lever is in the Park (P) position (A/T vehicles).
2.
3.
Turn the ignition switch to the ON (II) position, and make sure to close the driver’s door.
OnA/Tvehicles, brake pedal, and move the shift lever out of the Park (P) position.
push and hold the
82
4.
Push and hold the front of the
master door lock switch on the
driver’s door. You will hear a click.
Keep holding the switch until you
hear another click (after about 5
seconds).
5.
Release the switch, and within 5
seconds, turn the ignition switch
to the ACCESSORY (I) position.
move the shift
OnA/Tvehicles,
lever to the Park (P) position.
6.
Turn the ignition switch to the LOCK (0) position.
2010 Accord Sedan09/07/08 21:36:17 31TA5620_088
The driver’s door unlocks whenever you turn the ignition switch to the ACCESSORY (I) position. This is the default setting on M/T vehicles.
All doors unlock whenever you turn the ignition switch to the ACCESSORY (I) position.
Auto Door Unlocking The auto door unlocking feature has five possible settings:
The auto door unlocking is deactivated all the time.
the driver’s door OnA/Tvehicles, unlocks when you move the shift lever to the Park (P) position with the brake pedal depressed. This is the default setting.
All doors unlock when you move the shift lever to the Park (P) position with the brake pedal depressed (A/T vehicles).
Door Locks
ToturnofftheAutoDoorUnlock modes:
1.
Make sure the shift lever is in the Park (P) position (A/T vehicles).
2.
Turn the ignition switch to the ON (II) position, and open the driver’s door.
CONTINUED
83
2010 Accord Sedan09/07/08 21:36:26 31TA5620_089
Door Locks
3.
Push and hold the rear of the master door lock switch on the driver’s door. You will hear a click, and after about 5 seconds, you will hear another click.
ToprogramtheParkUnlockmode: Unlocksthedriver’sdoororalldoors whentheshiftleverismovedintothe Park(P)positionwiththebrakepedal depressed(A/Tvehiclesonly).
4.
Release the switch, and within 5
seconds, turn the ignition switch
to the LOCK (0) position.
1.
Make sure the shift lever is in the Park (P) position.
2.
Turn the ignition switch to the ON (II) position, and make sure to close the driver’s door.
84
3.
Push and hold the rear of the master door lock switch on the driver’s door. You will hear a click. Continue to hold the switch:
Until you hear another click (after about 5 seconds) to activate feature.
driver’sdoorunlock
Or, until you hear two more clicks (after about 10 seconds) to activate
alldoorsunlockfeature.
4.
Release the switch, and within 5
seconds, turn the ignition switch
to the LOCK (0) position.
2010 Accord Sedan09/07/08 21:36:36 31TA5620_090
ToprogramtheIgnitionSwitch Unlockmode: Unlocksthedriver’sdoororalldoors whentheignitionswitchismovedoutof theON(II)position.
3.
4.
1.
Make sure the shift lever is in the Park (P) position (A/T vehicles).
2.
Turn the ignition switch to the ON (II) position, and make sure to close the driver’s door.
Door Locks
OnA/Tvehicles, brake pedal, then move the shift lever out of the Park (P) position.
push and hold the
Push and hold the rear of the master door lock switch on the driver’s door. You will hear a click. Continue to hold the switch:
Until you hear another click (after about 5 seconds) to activate feature.
driver’sdoorunlock
Or, until you hear two more clicks (after about 10 seconds) to activate
alldoorsunlockfeature.
5.
Release the switch, and within 5
seconds, turn the ignition switch
to the ACCESSORY (I) position.
move the shift
OnA/Tvehicles,
lever to the Park (P) position.
6.
Turn the ignition switch to the LOCK (0) position.
Even if your vehicle’s battery is removed or goes dead, the system keeps the auto door lock/unlock setting which you selected.
85
2010 Accord Sedan09/05/18 18:23:11 31TA5620 0091
Door Locks, Remote Transmitter
Childproof Door Locks
Remote Transmitter
LEVER
LED
Unlock
UNLOCK BUTTON
Lock
PANIC BUTTON
LOCK BUTTON
TRUNK RELEASE BUTTON
The childproof door locks are designed to prevent children seated in the rear from accidentally opening the rear doors. Each rear door has a lock lever near the edge. With the lever in the LOCK position (lever is down), the door cannot be opened from the inside regardless of the position of the lock tab. To open the door, push the lock tab forward and use the outside door handle.
−
LOCK Press this button once to lock all doors. Some exterior lights will flash once. When you push LOCK twice within 5 seconds, you will hear a beep to verify that the doors are locked and the security system (if equipped) has set. You cannot lock the doors if any door is not fully closed or the key is in the ignition switch.
86
−
Press this button once
UNLOCK to unlock the driver’s door. Push it twice to unlock the remaining doors. Some exterior lights will flash twice each time you press the button.
The ceiling light and the door activated spotlights (if equipped) come on when you press the UNLOCK button if the lights are in the door activated position. If you do not open any door within 30 seconds, the light(s) will fade out. If you relock the doors with the remote transmitter before 30 seconds have elapsed, the light(s) will go off immediately.
If you do not open any door within 30
seconds, the doors automatically
relock and the security system (if
equipped) sets.
2010 Accord Sedan09/05/18 18:23:21 31TA5620 0092
You can also open all power windows and the moonroof (if equipped) from outside the vehicle with the remote transmitter (see page
105
).
−
Press this button for
PANIC about 2 seconds to attract attention: the horn will sound, and the exterior lights will flash for about 30 seconds. To cancel panic mode, press any other button on the remote transmitter, or turn the ignition switch to the ON (II) position.
−
Press and hold this
TRUNK button for about 1 second to open the trunk. You cannot open the trunk if the key is in the ignition switch.
Remote Transmitter
RemoteTransmitterCare
Avoid dropping or throwing the transmitter.
Protect the transmitter from extreme temperature.
Do not immerse the transmitter in any liquid.
If you lose a transmitter, the replacement needs to be reprogrammed by your dealer.
CONTINUED
87
2010 Accord Sedan09/05/18 18:23:32 31TA5620 0093
Remote Transmitter
ReplacingtheTransmitterBattery If it takes several pushes on the button to lock or unlock the doors, replace the battery as soon as possible.
Battery type: CR1616
SCREW
To replace the battery:
1.
Remove the screw at the base of the transmitter with a small Phillips-head screwdriver.
Be careful when removing NOTE: this screw as the head of the screw can strip out.
2.
Separate the transmitter by prying its middle seam with your fingernail.
88
BATTERY
TAB
3.
Inside the transmitter, separate the inner cover from the keypad by releasing the two tabs on the cover.
2010 Accord Sedan09/05/18 18:23:39 31TA5620 0094
Remote Transmitter
4.
Remove the old battery, and insert a new battery into the back of the cover with the
side facing down.
+
An improperly disposed of battery can hurt the environment. Always confirm local regulations for battery disposal.
5.
Install the parts in reverse order.
AsrequiredbytheFCC: ThisdevicecomplieswithPart15ofthe FCCrules.Operationissubjecttothe followingtwoconditions:(1)Thisdevice maynotcauseharmfulinterference,and (2)thisdevicemustacceptany interferencereceived,including interferencethatmaycauseundesired operation.
Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser’s authoritytooperatetheequipment.
ThisdevicecomplieswithIndustry CanadaStandardRSS-210. Operationissubjecttothefollowingtwo conditions:(1)thisdevicemaynotcause interference,and(2)thisdevicemust acceptanyinterferencethatmaycause undesiredoperationofthedevice.
89
2010 Accord Sedan09/05/18 18:23:50 31TA5620 0095
Trunk
Pull
To close the trunk, press down on the trunk lid.
Keep the trunk lid closed at all times
while driving to avoid damaging the
lid, and to prevent exhaust gas from
Carbon
getting into the interior. See
Monoxide Hazard
51
on page
TRUNK RELEASE LEVER
You can open the trunk in two ways: