2008 GMC Sierra Owners Manual

Download PDF Manual
torque setting of 12.5 ft-lbs (17Y). If the system is removed to install a bed liner, make sure there is no bed liner material in the installation points. Notice: If you tie down cargo using the horizontal slots on the top of the pickup box, you may damage the box. Using the horizontal slots on the top of the pickup box for tie-down locations may cause damage to the pickup box and would not be covered by your warranty. Only use the tie-down loops if you do not have the cargo management system. 2-58 Sunroof If your vehicle has a power sliding sunroof, the ignition needs to be turned to RUN, or the Retained Accessory Power (RAP) must be activated to open or close the sunroof. When RAP is active, the sunroof will work for 10 minutes after the ignition is turned off, or until the driver’s door is opened. See Retained Accessory Power (RAP) on page 2-23 for more information. There are two sunroof switches located in the overhead console above the rearview mirror. Vent: From the closed position, press the rear of the passenger’s side switch to vent the sunroof. To close the sunroof, press and hold the front of the passenger’s side switch. Manual-Open/Manual-Close: To open the sunroof press and hold the rear of the driver’s side switch until the sunroof reaches the desired position. To close the sunroof, press and hold the front of the driver’s side switch until the sunroof reaches the desired position. When the sunroof is opened, an air deﬂector will automatically raise. The air deﬂector will retract when the sunroof is closed. Express-Open/Express-Close: To express-open the sunroof, fully press and release the rear of the driver’s side switch. The sunroof will open automatically. To stop the sunroof partway, press the switch a second time. To express-close the sunroof, fully press and release the front of the driver’s side switch. The sunroof will close automatically. To stop the sunroof partway, press the switch a second time. The sunroof also has a sunshade which you can pull forward to block sun rays. The sunshade must be opened and closed manually. Anti-Pinch Feature: If an object is in the path of the sunroof while it is closing, the anti-pinch feature will detect the object and stop the sunroof from closing at the point of the obstruction. The sunroof will then open halfway, and the air deﬂector will raise. To close the sunroof once it has re-opened, refer to the Express-Close or Manual-Close functions described previously. If the sunroof is in the vent position, and there is an object in the path of the sunroof when it closing, the anti-pinch feature will detect the object and stop the sunroof. To close the sunroof once it has re-opened, refer to the Manual-Close or Express-Close functions described previously. 2-59 ✍ NOTES 2-60 Section 3 Instrument Panel Instrument Panel Overview ...............................3-4 Hazard Warning Flashers ................................3-6 Other Warning Devices ...................................3-6 Horn .............................................................3-6 Tilt Wheel .....................................................3-6 Turn Signal/Multifunction Lever .........................3-7 Turn and Lane-Change Signals ........................3-8 Headlamp High/Low-Beam Changer ..................3-8 Flash-to-Pass .................................................3-9 Windshield Wipers ..........................................3-9 Windshield Washer .......................................3-10 Cruise Control ..............................................3-11 Exterior Lamps .............................................3-14 Headlamps on Reminder ................................3-15 Daytime Running Lamps (DRL) .......................3-16 Automatic Headlamp System ..........................3-16 Puddle Lamps ..............................................3-17 Fog Lamps ..................................................3-17 Instrument Panel Brightness ...........................3-18 Dome Lamps ...............................................3-18 Dome Lamp Override ....................................3-18 Entry Lighting ...............................................3-18 Exit Lighting .................................................3-18 Reading Lamps ............................................3-19 Cargo Lamp .................................................3-19 Electric Power Management ...........................3-19 Battery Run-Down Protection ..........................3-20 Accessory Power Outlet(s) .............................3-20 Ashtray(s) and Cigarette Lighter ......................3-21 Climate Controls ............................................3-22 Climate Control System (With Air Conditioning) ...............................3-22 Climate Control System (Heater Only) ..............3-24 Dual Automatic Climate Control System ...........3-26 Outlet Adjustment .........................................3-32 Warning Lights, Gages, and Indicators ............3-33 Instrument Panel Cluster ................................3-34 Speedometer and Odometer ...........................3-35 Trip Odometer ..............................................3-35 Tachometer .................................................3-35 Safety Belt Reminders ...................................3-36 Airbag Readiness Light ..................................3-37 Passenger Airbag Status Indicator ...................3-38 Charging System Light ..................................3-40 Voltmeter Gage ............................................3-40 Brake System Warning Light ..........................3-41 Antilock Brake System Warning Light ...............3-42 StabiliTrak® Indicator Light ..............................3-43 Engine Coolant Temperature Gage ..................3-43 3-1 Section 3 Instrument Panel Audio System(s) .............................................3-76 Setting the Clock ..........................................3-77 Radio(s) (MP3) .............................................3-79 Using an MP3 (Radio with Six-Disc Player) ........................3-97 Using an MP3 (Radio with CD and DVD Player) ...............3-102 XM Radio Messages ...................................3-107 Navigation/Radio System ..............................3-108 Rear Seat Entertainment (RSE) System .........3-109 Rear Seat Audio (RSA) ................................3-118 Theft-Deterrent Feature ................................3-120 Audio Steering Wheel Controls ......................3-120 Radio Reception .........................................3-121 Fixed Mast Antenna ....................................3-122 XM™ Satellite Radio Antenna System ............3-122 Tire Pressure Light .......................................3-44 Malfunction Indicator Lamp .............................3-44 Oil Pressure Gage ........................................3-48 Oil Pressure Light .........................................3-49 Security Light ...............................................3-49 Fog Lamp Light ............................................3-50 Cruise Control Light ......................................3-50 Highbeam On Light .......................................3-50 Tow/Haul Mode Light ....................................3-50 Fuel Gage ...................................................3-51 Driver Information Center (DIC) .......................3-52 DIC Operation and Displays (Using DIC Buttons) ...................................3-52 DIC Operation and Displays (Using Trip Odometer Reset Stem) ..............3-58 DIC Warnings and Messages .........................3-59 DIC Vehicle Customization (With DIC Buttons) ....3-68 3-2 ✍ NOTES 3-3 Instrument Panel Overview United States version shown; Canada similar 3-4 A. Air Outlets. See Outlet Adjustment on page 3-32. B. Turn Signal/Multifunction Lever. See Turn Signal/Multifunction Lever on page 3-7. C. Instrument Panel Cluster. See Instrument Panel Cluster on page 3-34. D. Hazard Warning Flasher Button. See Hazard Warning Flashers on page 3-6. E. Shift Lever. See Automatic Transmission Operation on page 2-27. F. Tow/Haul Selector Button (If Equipped). See Tow/Haul Mode on page 2-31. G. Driver Information Center Controls (DIC). See Driver Information Center (DIC) on page 3-52. H. Audio System. See Audio System(s) on page 3-76. I. Exterior Lamps Control. See Exterior Lamps on page 3-14. J. Integrated Trailer Brake Controller (If Equipped). See Towing a Trailer on page 4-41. K. Dome Lamp Override Button. See Dome Lamp Override on page 3-18. Dome Lamp Knob. See Dome Lamps on page 3-18. L. Cruise Control Buttons. See Cruise Control on page 3-11. M. Hood Release. See Hood Release on page 5-11. N. Parking Brake. See Parking Brake on page 2-32. O. Tilt Wheel Lever. See Tilt Wheel on page 3-6. P. Horn. See Horn on page 3-6. Q. Audio Steering Wheel Controls. See Audio Steering Wheel Controls on page 3-120. R. Climate Controls. See Climate Control System (With Air Conditioning ) on page 3-22 or Climate Control System (Heater Only) on page 3-24 or Dual Automatic Climate Controls (If Equipped). See Dual Automatic Climate Control System on page 3-26. S. Accessory Power Outlets. See Accessory Power Outlet(s) on page 3-20. Cigarette Lighter (If Equipped). See Ashtray(s) and Cigarette Lighter on page 3-21. T. StabiliTrak® Button (If Equipped). See StabiliTrak® System on page 4-5. Pedal Adjust Button (If Equipped). See Adjustable Throttle and Brake Pedal on page 2-25. Rear Park Assist Disable Button (If Equipped). See Ultrasonic Rear Parking Assist (URPA) on page 2-43. Heated Windshield Washer Fluid Button (If Equipped). See Windshield Washer on page 3-10. U. Passenger Airbag Off Control (If Equipped). See Passenger Sensing System on page 1-63. V. Glove Box. See Glove Box on page 2-56. 3-5 Hazard Warning Flashers The hazard warning ﬂashers warn others. They also let police know you have a problem. The hazard warning ﬂasher button is located on top of the steering column. Press the button to make the front and rear turn signal lamps ﬂash on and off. Press the button again to turn the ﬂashers off. The hazard warning ﬂashers work no matter what ignition position the key is in, and even if the key is not in the ignition. When the hazard warning ﬂashers are on, your vehicle’s turn signals will not work. Other Warning Devices If you carry reﬂective triangles, you can set them up at the side of the road about 300 feet (100 m) behind your vehicle. Horn To sound the horn, press the horn symbols located on the steering wheel. Tilt Wheel The tilt wheel lets you adjust the steering wheel before you drive. Raise it to the highest level to give your legs more room when exiting or entering the vehicle. 3-6 The tilt steering wheel lever is located on the lower left side of the steering column. To tilt the wheel, hold the steering wheel and pull the lever. Then move the steering wheel to a comfortable position and release the lever to lock the wheel in place. Turn Signal/Multifunction Lever The lever on the left side of the steering column includes the following: (cid:129) GTurn and Lane Change Signals. See Turn and Lane-Change Signals on page 3-8. (cid:129) 53Headlamp High/Low-Beam Changer. See Headlamp High/Low-Beam Changer on page 3-8. Flash-to-Pass. See Flash-to-Pass on page 3-9. (cid:129) NWindshield Wipers. See Windshield Wipers on page 3-9. (cid:129) LWindshield Washer. See Windshield Washer on page 3-10. For information on the exterior lamps, see Exterior Lamps on page 3-14. 3-7 (cid:129) Turn Signal On Chime If your turn signal is left on for more than 3/4 of a mile (1.2 km), a chime sounds at each ﬂash of the turn signal and the message TURN SIGNAL ON also appears in the Driver Information Center (DIC). Move the turn signal lever to the off position, to turn the chime and message off. Headlamp High/Low-Beam Changer 53(Headlamp High/Low Beam Changer): Push the lever toward the instrument panel, to change the headlamps from low to high beam. Pull the multifunction lever toward you and release it, to return to low-beam headlamps. When the high beams are on, this indicator light on the instrument panel cluster will also be on. Turn and Lane-Change Signals The turn signal has two upward (for right) and two downward (for left) positions. Each position signals a turn or a lane change. To signal a turn, move the lever all the way up or down. When the turn is ﬁnished, the lever returns automatically to the starting position. To signal a lane change, raise or lower the lever until the arrow starts to ﬂash. Hold it there until your lane change is completed. The lever returns to the starting position by itself when it is released. An arrow on the instrument panel cluster will ﬂash in the direction of the turn or lane change. If the arrows ﬂash more quickly than normal as you signal a turn or a lane change, a signal bulb might be burned out and other drivers will not see the turn signal. If a bulb is burned out, replace it to help avoid an accident. If the arrows do not come on when you signal a turn, check for burned-out bulbs and a blown fuse. See Fuses and Circuit Breakers on page 5-108. 3-8 Flash-to-Pass This feature lets you use the high-beam headlamps to signal a driver in front of you that you want to pass. It works even if the headlamps are in the automatic position. To use it, pull the turn signal lever toward you, then release it. If the headlamps are in the automatic position or on low beam, your high-beam headlamps turn on. They will stay on as long as you hold the lever toward you. The high-beam indicator on the instrument panel cluster comes on. Release the lever to return to normal operation. Windshield Wipers Clear ice and snow from the wiper blades before using them. If they are frozen to the windshield, gently loosen or thaw them. Damaged wiper blades may not clear the windshield well, making it harder to see and drive safely. If the blades do become damaged, install new blades or blade inserts. For more information, see Windshield Wiper Blade Replacement on page 5-57. Heavy snow or ice can overload the wiper motor. A circuit breaker will stop the motor until it cools down. Clear away snow or ice to prevent an overload. Turn the band with the wiper symbol to control the windshield wipers. 8(Mist): Turn the band to mist for a single wiping cycle. Hold it there until the wipers start. Then let go. The wipers stop after one wipe. Hold the band on mist longer, for more wipe cycles. 9(Off): To stop the wipers, move the band to off. 6 (Delay): Turn the band to adjust the delay time. The delay between wiping cycles becomes shorter as the band is moved to the top of the lever. This can be very useful in light rain or snow. 6 (Low Speed): Turn the band away from you to the ﬁrst solid band past the delay settings, for steady wiping at low speed. ? (High Speed): Turn the band further, to the second solid band past the delay settings, for high-speed wiping. 3-9 Windshield Washer {CAUTION: In freezing weather, do not use your washer until the windshield is warmed. Otherwise the washer ﬂuid can form ice on the windshield, blocking your vision. L(Washer Fluid): Push the paddle marked with the windshield washer symbol at the top of the multifunction lever, to spray washer ﬂuid on the windshield. The wipers clear the window and then either stop or return to the preset speed. 3-10 Heated Windshield Washer For vehicles with the heated windshield washer ﬂuid system it can be used to help clear ice, snow, tree sap, or bugs from your windshield. The button is located in the switchbank under the climate controls. Push the heated washer ﬂuid button to activate the heated windshield washer ﬂuid system. The indicator light will ﬂash. This activation initiates four heated wash/wipe cycles. The ﬁrst heated wash/wipe cycle may take up to 40 seconds to occur, depending on outside temperature. After the ﬁrst wash/wipe cycle, it may take up to 20 seconds for each of the remaining cycles to begin. Press the button again to turn off the heated windshield washer ﬂuid system or it will automatically turn off after four wipe cycles have been completed. When the heated windshield washer ﬂuid system is activated under certain outside temperature conditions, steam may ﬂow out of the washer nozzles for a short period of time before washer ﬂuid is sprayed. This is a normal condition. When you apply your brakes, cruise control is turned off. If your vehicle has the StabiliTrak® system and begins to limit wheel spin while you are using cruise control, the cruise control will automatically disengage. See StabiliTrak® System on page 4-5. When road conditions allow you to safely use it again, you may turn the cruise control back on. Cruise Control {CAUTION: Cruise control can be dangerous where you cannot drive safely at a steady speed. So, do not use your cruise control on winding roads or in heavy traffic. Cruise control can be dangerous on slippery roads. On such roads, fast changes in tire traction can cause excessive wheel slip, and you could lose control. Do not use cruise control on slippery roads. With cruise control, you can maintain a speed of about 25 mph (40 km/h) or more without keeping your foot on the accelerator. This can really help on long trips. Cruise control does not work at speeds below about 25 mph (40 km/h). 3-11 The cruise control buttons are located on left side of the steering wheel. Setting Cruise Control Cruise control will not work if the parking brake is set, or if the master cylinder brake ﬂuid level is low. The cruise control light on the instrument panel cluster will come on after the cruise control has been set to the desired speed. {CAUTION: If you leave your cruise control on when you are not using cruise, you might hit a button and go into cruise when you do not want to. You could be startled and even lose control. Keep the cruise control switch off until you want to use cruise control. 1. Press the cruise control On/Off button. 2. Get up to the desired speed. 3. Press the SET− button located on the steering wheel and release it. 4. Take your foot off the accelerator. T (On/Off): This button can both activate and turn off the system. The indicator light is on when cruise control is on and turns off when cruise control is off. + RES (Resume/Accelerate): Press this button to make the vehicle accelerate or resume to a previously set speed. SET − (Set/Coast): Press this button to set the speed or make the vehicle decelerate. [ (Cancel): Press this button to cancel cruise control without erasing the set speed from memory. 3-12 Resuming a Set Speed If you apply the brakes while the cruise control is set, the cruise control is disengaged. But it does not need to be reset. Once the vehicle speed reaches about 25 mph (40 km/h) or more, press the +RES button on the steering wheel. The vehicle will go back to the previous set speed and stay there. Increasing Speed While Using Cruise Control To increase the cruise speed while using cruise control: (cid:129) Press and hold the +RES button on the steering wheel until you reach your new desired speed, then release it. To increase vehicle speed in small increments, press the +RES button. Each time this is done, the vehicle will go about 1 mph (1.6 km/h) faster. Reducing Speed While Using Cruise Control To reduce the vehicle speed while using cruise control: (cid:129) Press and hold the SET– button on the steering wheel until the desired lower speed is reached, then release it. To slow down in very small amounts, press the SET– button on the steering wheel brieﬂy. Each time this is done, the vehicle will go about 1 mph (1.6 km/h) slower. Passing Another Vehicle While Using Cruise Control Use the accelerator pedal to increase the vehicle speed. When you take your foot off the pedal, the vehicle will slow down to the previous set cruise speed. 3-13 (cid:129) (cid:129) Using Cruise Control on Hills How well the cruise control will work on hills depends upon the vehicle speed, load, and the steepness of the hills. While going up steep hills, you might have to step on the accelerator pedal to maintain the vehicle’s speed. While going downhill, you might have to brake or shift to a lower gear to keep the vehicle’s speed down. Of course, applying the brake turns off the cruise control. Many drivers ﬁnd this to be too much trouble and do not use cruise control on steep hills. Ending Cruise Control There are three ways to end cruise control: (cid:129) Step lightly on the brake pedal. (cid:129) Press the cancel button on the steering wheel. (cid:129) Press the On/Off button on the steering wheel. Erasing Speed Memory When the cruise control or the ignition is turned off, the cruise control set speed memory is erased. Exterior Lamps The exterior lamps control is located on the instrument panel to the left of the steering wheel. It controls the following systems: (cid:129) Headlamps Taillamps (cid:129) Parking Lamps License Plate Lamps Instrument Panel Lights The exterior lamps control has four positions: O(Off): Turn the control to this position to turn off the automatic headlamps and daytime running lamps (DRL). Turn the headlamp control to the off position again to turn the automatic headlamps or DRL back on. For vehicles ﬁrst sold in Canada, the off position will only work when the vehicle is shifted into PARK (P). 3-14 (cid:129) (cid:129) (cid:129) When the headlamps are turned on while the vehicle is on, the headlamps turn off automatically 10 minutes after the ignition is turned off. When the headlamps are turned on while the vehicle is off, the headlamps will stay on for 10 minutes before automatically turning off to prevent the battery from being drained. Turn the headlamp control to off and then back to the headlamp on position to make the headlamps stay on for an additional 10 minutes. Push the turn signal/multifunction lever toward the instrument panel to change the headlamps from low beam to high beam. Headlamps on Reminder A reminder chime will sound when the headlamps or parking lamps are manually turned on and the ignition is off, in LOCK, ACCESSORY, or a door is open. Turn the light off, then back on, to stop the chime. AUTO (Automatic): Turn the control to this position to automatically turn on the headlamps at normal brightness, together with the following: (cid:129) Parking Lamps Instrument Panel Lights Taillamps License Plate Lamps When the vehicle is turned off and the headlamps are in AUTO, the headlamps may automatically remain on for a set time. The time of the delay can be changed using the DIC. See Driver Information Center (DIC) on page 3-52. ;(Parking Lamps): Turn the control to this position to turn on the parking lamps together with the following: Instrument Panel Lights Taillamps License Plate Lamps 2(Headlamps): Turn the control to this position to turn on the headlamps together with the following: (cid:129) Parking Lamps Instrument Panel Lights Taillamps License Plate Lamps 3-15 (cid:129) (cid:129) (cid:129) (cid:129) (cid:129) (cid:129) (cid:129) (cid:129) (cid:129) Daytime Running Lamps (DRL) Daytime Running Lamps (DRL) can make it easier for others to see the front of your vehicle during the day. DRL can be helpful in many different driving conditions, but they can be especially helpful in the short periods after dawn and before sunset. Fully functional daytime running lamps are required on all vehicles ﬁrst sold in Canada. The DRL system will come on when the following conditions are met: The ignition is on. The exterior lamps control is in AUTO. The transmission is not in PARK (P). The light sensor determines it is daytime. When the DRL are on, only the DRL lamps will be on. The taillamps, sidemarker, and other lamps will not be on. The instrument panel will not be lit up either. When it begins to get dark, the automatic headlamp system will switch from DRL to the headlamps. To turn off the DRL lamps, turn the exterior lamps control to the OFF position and then release. For vehicles ﬁrst sold in Canada, the transmission must be in the PARK (P) position, before the DRL lamps can be turned off. 3-16 Automatic Headlamp System When it is dark enough outside, the automatic headlamp system will turn on the headlamps at the normal brightness, along with the taillamps, sidemarker, parking lamps, and the instrument panel lights. The radio lights will also be dim. To turn off the automatic headlamp system, turn the exterior lamps switch to the off position and then release it. For vehicles ﬁrst sold in Canada, the transmission must be in the PARK (P) position, before the automatic headlamp system can be turned off. The vehicle has a light sensor located on the top of the instrument panel in the defroster grille that regulates when the automatic headlamps turn on. Be sure it is not covered, or the headlamps will come on whenever the ignition is on. The system may also turn on the headlamps when driving through a parking garage, heavy overcast weather, or a tunnel. This is normal. There is a delay in the transition between the daytime and nighttime operation of the Daytime Running Lamps (DRL) and the automatic headlamp systems so that driving under bridges or bright overhead street lights does not affect the system. The DRL and automatic headlamp system will only be affected when the light sensor detects a change in lighting lasting longer than the delay. (cid:129) (cid:129) (cid:129) (cid:129) If the vehicle is started in a dark garage, the automatic headlamp system will come on immediately. Once the vehicle leaves the garage, it takes approximately one minute for the automatic headlamp system to change to DRL if it is bright enough outside. During that delay, the instrument panel cluster may not be as bright as usual. Make sure the instrument panel brightness control is in the full bright position. See Instrument Panel Brightness on page 3-18. To idle the vehicle with the automatic headlamp system off, turn the control to the off position. The headlamps will also stay on after you exit the vehicle. This feature can be programmed using the Driver Information Center (DIC). See DIC Vehicle Customization (With DIC Buttons) on page 3-68. The regular headlamp system can be turned on when needed. Puddle Lamps If your vehicle has puddle lamps, they come on when the unlock button on the Remote Keyless Entry (RKE) Transmitter is pressed. The lamps time out or turn off once the engine is started. Fog Lamps The vehicle’s fog lamps provide better visibility in foggy or misty conditions. The fog lamp button is located on the left side of the instrument panel. The parking lamps and/or low-beam headlamps must be on for the fog lamps to work. Press the button to turn the fog lamps on while the headlamps are on. Press the button again to turn them off. An indicator light in the button comes on when the fog lamps are in use. Remember, fog lamps alone do not give off as much light as the headlamps. Never use the fog lamps in the dark without turning on the headlamps. The fog lamps go off whenever the high-beam headlamps come on. When the high beams turn off, the fog lamps come on again. 3-17 The fog lamps are cancelled after the ignition is turned off. If you still want to use the fog lamps after the vehicle is restarted, press the fog lamp button again. Some localities have laws that require the headlamps to be on along with the fog lamps. Instrument Panel Brightness D(Instrument Panel Brightness): This feature controls the brightness of the instrument panel lights and is located next to the exterior lamp control. Push the knob to extend out and then it can be turned. Turn the knob clockwise or counterclockwise to brighten or dim the instrument panel lights. Turning the knob to the farthest clockwise position turns on the dome lamps. Dome Lamps The dome lamps come on when any door is opened. They turn off after all the doors are closed. The dome lamps can also be turned on by turning the instrument panel brightness knob, located next to the exterior lamps control, clockwise to the farthest position. In this position, the dome lamps remain on whether a door is opened or closed. 3-18 Dome Lamp Override The dome lamp override button is located next to the exterior lamps control. k (Dome Off): Press the button in and the dome lamps remain off when a door is opened. Press the button again to return it to the extended position so that the dome lamps come on when a door is opened. Entry Lighting Your vehicle has an illuminated entry feature. When a door is opened, the dome lamps and puddle lamps come on if the dome override feature is not in use. If the dome override feature is used, the lamps do not come on. Exit Lighting The interior lamps come on when the key is removed from the ignition. They turn off automatically in 20 seconds. The lights do not come on if the dome override button is pressed in. Reading Lamps If your vehicle has reading lamps they are located on the overhead console. To turn on the reading lamps, press the button located next to each lamp. To turn them off, press the button again. Your vehicle may also have reading lamps in other locations. To turn the lamps on or off, press the button located next to the lamp. If your vehicle has a DVD Rear Seat Entertainment (RSE) system, press the lamp lenses to turn the lamps on or off. The lamps are ﬁxed and cannot be adjusted. Cargo Lamp The cargo lamps come on by turning the instrument panel brightness control knob to the farthest clockwise position. This knob is located on the instrument panel and also turns on the dome lamps. The cargo lamp can be used if more light is needed in the cargo area of the vehicle or in the top-box storage units. Electric Power Management The vehicle has Electric Power Management (EPM) that estimates the battery’s temperature and state of charge. It then adjusts the voltage for best performance and extended life of the battery. When the battery’s state of charge is low, the voltage is raised slightly to quickly put the charge back in. When the state of charge is high, the voltage is lowered slightly to prevent overcharging. If the vehicle has a voltmeter gage or a voltage display on the Driver Information Center (DIC), you may see the voltage move up or down. This is normal. If there is a problem, an alert will be displayed. The battery can be discharged at idle if the electrical loads are very high. This is true for all vehicles. This is because the generator (alternator) may not be spinning fast enough at idle to produce all the power that is needed for very high electrical loads. A high electrical load occurs when several of the following loads are on: headlamps, high beams, fog lamps, rear window defogger, climate control fan at high speed, heated seats, engine cooling fans, trailer loads, and loads plugged into accessory power outlets. 3-19 EPM works to prevent excessive discharge of the battery. It does this by balancing the generator’s output and the vehicle’s electrical needs. It can increase engine idle speed to generate more power, whenever needed. It can temporarily reduce the power demands of some accessories. Normally, these actions occur in steps or levels, without being noticeable. In rare cases at the highest levels of corrective action, this action may be noticeable to the driver. If so, a Driver Information Center (DIC) message might be displayed, such as Battery Saver Active or Service Battery Charging System. If this message is displayed, it is recommended that the driver reduce the electrical loads as much as possible. See DIC Warnings and Messages on page 3-59. Battery Run-Down Protection This feature shuts off the dome and reading lamps, if they are left on for more than 10 minutes after the ignition is turned off. The cargo lamp shuts off after 20 minutes. This prevents the battery from running down. Accessory Power Outlet(s) Accessory power outlets can be used to connect auxiliary electrical equipment, such as a cellular telephone or CB radio. There are two accessory power outlets on the instrument panel, one inside the center ﬂoor console and one on the rear of the center ﬂoor console. To access the accessory power outlet inside the center ﬂoor console, press the button on the side of the console door. See Center Console Storage on page 2-57 for more information. To use an accessory power outlet, remove the protective cap. When not in use, always cover the accessory power outlet with the protective cap. Notice: power outlet, the battery may drain causing your vehicle not to start or damage to the battery. This would not be covered by the warranty. Always unplug all electrical devices when turning off your vehicle. If electrical devices are left plugged into a 3-20 Certain electrical accessories are not compatible with the accessory power outlets and could result in blown vehicle or adapter fuses. If you experience a problem, see your dealer/retailer for additional information on accessory power outlets. The accessory power outlets are powered, even when the ignition is in LOCK/OFF. Continuing to use power outlets while the ignition is in LOCK/OFF may cause the vehicle’s battery to run down. Notice: Adding any electrical equipment to your vehicle may damage it or keep other components from working as they should. The repairs would not be covered by your warranty. Do not use equipment exceeding maximum amperage rating of 20 amperes. Check with your dealer/retailer before adding electrical equipment. When adding electrical equipment, be sure to follow the proper installation instructions included with the equipment. Notice: damage not covered by your warranty. Do not hang any type of accessory or accessory bracket from the plug because the power outlets are designed for accessory power plugs only. Improper use of the power outlet can cause If you put papers, pins, or other ﬂammable Ashtray(s) and Cigarette Lighter Your vehicle may have a front ashtray located near the center of the instrument panel. Pull on the door to open it. The ashtray may have a cigarette lighter. Notice: items in the ashtray, hot cigarettes or other smoking materials could ignite them and possibly damage your vehicle. Never put ﬂammable items in the ashtray. To remove the ashtray, open the door and pull the ashtray bin toward you. To replace the ashtray, insert the ashtray bin inside the ashtray door and press down until it engages. To use the cigarette lighter, push it in all the way, and let go. When it is ready for use, the lighter pops back out. Notice: Holding a cigarette lighter in while it is heating does not let the lighter back away from the heating element when it is hot. Damage from overheating can occur to the lighter or heating element, or a fuse could be blown. Do not hold a cigarette lighter in while it is heating. 3-21 Climate Controls Climate Control System (With Air Conditioning) With this system you can control the heating, cooling, and ventilation for your vehicle. Operation 9 (Fan): Turn the left knob clockwise or counterclockwise to increase or decrease the fan speed. Turn the knob all the way counterclockwise to turn the front system off. Temperature Control: Turn the center knob clockwise or counterclockwise to increase or decrease the temperature inside the vehicle. 3-22 Use the right knob to select from the following modes: The right knob can be positioned between two modes to select a combination of those two modes. H(Vent): This mode directs air to the instrument panel outlets. )(Bi-Level): This mode directs half of the air to the instrument panel outlets and half to the ﬂoor outlets. 6(Floor): This mode directs most of the air to the ﬂoor outlets with some air directed to the windshield and side window outlets. In this mode, the system will automatically select outside air. Recirculation cannot be selected in ﬂoor mode. The right knob may also be used to select the defrost and defog mode. For more information, see “Defogging and Defrosting” later in this section. : (Outside Air): Press this button to turn the outside air mode on. When the button is pressed, an indicator light will come on. When this mode is on, outside air will circulate throughout the vehicle. The outside air mode can be used with all modes, but it cannot be used with the recirculation mode. ?(Recirculation): Press this button to turn the recirculation mode on. When the button is pressed, an indicator light will come on. This mode keeps outside air from entering the vehicle. It can be used to reduce outside air and prevent odors from entering the vehicle. Recirculation may also help cool the air inside the vehicle more quickly once the temperature inside the vehicle is less than the outside temperature. The recirculation mode cannot be used with ﬂoor, defog or defrost modes. If recirculation is selected with one of these modes, the indicator light will ﬂash three times and then turn off. While in recirculation mode the windows may fog when the weather is cold and damp. To clear the fog, select either the defog or defrost mode and increase the fan speed. The recirculation mode can be turned off by pressing the outside air button, or by turning off the ignition. #(Air Conditioning): Press this button to turn the air conditioning system on or off. When this button is pressed, an indicator light on the button will come on to let you know the air conditioning is activated. The air conditioning can be selected in any mode as long as the fan switch is on. The air conditioning system removes moisture from the air, so you may sometimes notice a small amount of water dripping underneath your vehicle while idling or after turning off the engine. This is normal. Defogging and Defrosting Fog or frost on the inside of windows is a result of high humidity (moisture) condensing on the cool window glass. This can be minimized if the climate control system is used properly. To avoid fogging windows on rainy and humid days at temperatures above freezing, run the air conditioning compressor. It is best to avoid the use of the recirculation mode, except when maximum A/C performance is needed or for short times to avoid exterior odors. Turn the right knob to select the defog or defrost mode. -(Defog): This mode clears the windows of fog or moisture and warm the passengers. The air is directed to the windshield, ﬂoor outlets, and side window vents. 0(Defrost): This mode removes fog or frost from the windshield more quickly. A portion of the air is directed to the windshield and the side window vents, with some air directed to the ﬂoor vents. The system will automatically force outside air into the vehicle. The recirculation mode cannot be selected in the defog or defrost mode. When either mode is selected, the system runs the air conditioning compressor, unless the outside temperature is close to freezing. Do not drive the vehicle until all the windows are clear. 3-23 Rear Window Defogger If your vehicle has a rear window defogger it uses a warming grid to remove fog from the rear window. The rear window defogger will only work when the ignition is in RUN. <(Rear): Press this button to turn the rear window defogger on or off. An indicator light on the button will come on to let you know that the rear window defogger is activated. The rear window defogger will only work when the ignition is in RUN. The rear window defogger will stay on for approximately 10 minutes after the button is pressed, unless the ignition is turned to ACC or LOCK. The defogger can also be turned off by pressing the button again or by turning off the engine. Notice: Do not use anything sharp on the inside of the rear window. If you do, you could cut or damage the warming grid, and the repairs would not be covered by your warranty. Do not attach a temporary vehicle license, tape, a decal or anything similar to the defogger grid. 3-24 Climate Control System (Heater Only) With this system you can control the heating and ventilation for your vehicle. Operation 9(Fan): Turn the left knob clockwise or counterclockwise to increase or decrease the fan speed. Turn the knob all the way counterclockwise to turn the front system off. Temperature Control: Turn the center knob clockwise or counterclockwise to increase or decrease the temperature inside the vehicle. Use the right knob to select from the following modes: The right knob can be positioned between two modes to select a combination of those two modes. H(Vent): This mode directs air to the instrument panel outlets. )(Bi-Level): This mode directs half of the air to the instrument panel outlets and to the ﬂoor outlets. 6(Floor): This mode directs most of the air to the ﬂoor outlets with some air directed to the windshield, side window outlets, and second row ﬂoor outlets. In this mode, the system will automatically select outside air. Defogging and Defrosting Fog or frost on the inside of windows is a result of high humidity (moisture) condensing on the cool window glass. This can be minimized if the climate control system is used properly. Turn the right knob to select the defog or defrost mode. -(Defog): This mode clears the windows of fog or moisture and warm the passengers. The air is directed to the windshield, ﬂoor outlets, and side window vents. 0(Defrost): This mode removes fog or frost from the windshield more quickly. A portion of the air is directed to the windshield and the side window vents, with some air directed to the ﬂoor vents. The system will automatically force outside air into the vehicle. Do not drive the vehicle until all the windows are clear. 3-25 Driver and Passenger Side Temperature Controls The driver and passenger side temperature buttons are used to adjust the temperature of the air coming through the system on the driver or passenger’s side of the vehicle. The temperature can be adjusted even if the system is turned off. This is possible since outside air always ﬂows through the system as the vehicle is moving forward unless it is set to recirculation mode. See “Recirculation” later in this section. Press the + or − buttons to increase or decrease the cabin temperature. The driver side or passenger side temperature display shows the temperature setting decreasing or increasing. The passenger’s temperature setting can be set to match the driver’s temperature setting by pressing the PASS button and turning off the PASS indicator. When the passenger’s temperature setting is set different than the driver’s setting, the indicator on the PASS button illuminates and both the driver’s side and passenger’s side temperature displays are shown. Dual Automatic Climate Control System The heating, cooling, and ventilation in the vehicle can be controlled with this system. The vehicle also has a ﬂow-through ventilation system described later in this section. Different climate control settings can be selected for the driver and passengers. 3-26 Automatic Operation AUTO (Automatic): When automatic operation is active the system controls the inside temperature, the air delivery, and the fan speed. Use the steps below to place the entire system in automatic mode: 1. Press the AUTO button. When AUTO is selected, the display changes to show the current temperature(s) and AUTO is lit on the display. The current air delivery mode and fan speed are also displayed for about 5 seconds. When AUTO is selected, the air conditioning operation and air inlet are automatically controlled. The air conditioning compressor may run when the outside temperature is above freezing. The air inlet will normally be set to outside air. If it is hot outside, the air inlet may automatically switch to the recirculate mode to help quickly cool down the air inside the vehicle. The light on the button comes on in recirculation. 2. Set the driver’s and passenger’s temperature. To ﬁnd your comfort setting, start with a 74°F (23°C) temperature setting and allow about 20 minutes for the system to regulate. Use the driver’s or passenger’s temperature buttons to adjust the temperature setting as necessary. If you choose the temperature setting of 60°F (15°C), the system remains at the maximum cooling setting. If you choose the temperature setting of 90°F (32°C), the system remains at the maximum heat setting. Choosing either maximum setting will not cause the vehicle to heat or cool any faster. Be careful not to cover the solar sensor located on the top of the instrument panel near the windshield. This sensor regulates air temperature based on sun load. For more information on the solar sensor, see “Sensors” later in this section. 3-27 To avoid blowing cold air in cold weather, the system delays turning the fan on until warm air is available. The length of delay depends on the engine coolant temperature. Pressing the fan switch overrides this delay and changes the fan to a selected speed. O(On/Off): Press this button to turn off the climate control system. Outside air still enters the vehicle, and is directed to the ﬂoor. This direction can be changed by pressing the mode button. Recirculation can be selected once you have selected vent or bi-level mode. The temperature can also be adjusted using either temperature button. If the air delivery mode or temperature settings are adjusted with the system off, the display illuminates brieﬂy to show the settings and then returns to off. Press the on/off button or the up down arrows on the fan switch, the defrost button, AUTO button, or the air conditioning button to turn the system on when it is off. Manual Operation The air delivery mode or fan speed can be manually adjusted. DC (Fan): These buttons let you manually adjust the fan speed. Press D to increase fan speed and C to decrease fan speed. Pressing either fan button while the system is off turns the system on. Pressing either fan button while in automatic control places the fan under manual control. The fan setting remains displayed and the AUTO light turns off. The air delivery mode remains under automatic control. HG (Mode): Press H and G to manually change the direction of the airﬂow in the vehicle. Repeatedly press either button until the desired mode appears on the display. Pressing either mode button while the system is off changes the air delivery mode without turning the system on. Pressing either mode button while in automatic control places the mode under manual control. The air delivery mode setting is displayed and the AUTO light turns off. The fan remains under automatic control. 3-28 H(Vent): Air is directed to the instrument panel outlets. )(Bi-Level): Air is directed partly to the instrument panel outlets and to the ﬂoor outlets. A little air is directed towards the windshield and side window outlets. Cooler air is directed to the upper outlets and warmer air to the ﬂoor outlets. 6(Floor): Air is directed to the ﬂoor outlets, with some to the windshield, side window outlets, and second row ﬂoor outlets. In this mode, the system will automatically select outside air. -(Defog): See “Defogging and Defrosting” later in this section. @(Recirculation): Press this button to turn the recirculation mode on. When the button is pressed, an indicator light comes on. This mode keeps outside air from entering the vehicle. It can be used to reduce outside air and prevent odors from entering the vehicle. Recirculation may also help cool the air inside the vehicle more quickly once the temperature inside the vehicle is less than the outside temperature. The recirculation mode cannot be used with ﬂoor, defog, or defrost modes. If recirculation is selected with one of those modes, the indicator light ﬂashes three times and then turns off. The air conditioning compressor also comes on when this mode is activated. While in recirculation mode the windows may fog when the weather is cold and damp. To clear the fog, select either the defog or defrost mode and increase the fan speed. The recirculation mode can be turned off by pressing the outside air button, or by turning off the ignition. ; (Outside Air): Press this button to turn on the outside air mode. When this mode is selected, air from outside the vehicle circulates throughout the vehicle. An indicator light on the button comes on to show that it is activated. The outside air mode can be used with all modes, but it cannot be used with the recirculation mode. 3-29 Sensors Air Conditioning # (Air Conditioning): Press this button to turn the air conditioning (A/C) compressor on and off. When air conditioning is selected, an indicator light comes on to show that the air conditioning has been activated. Pressing this button when the outside temperature is too cool for air conditioning makes the air conditioning indicator ﬂash three times and then turn off to let you know the air conditioning mode is not available. If the air conditioning is on and the outside temperature drops below a temperature which is too cool for air conditioning to be effective, the air conditioning light turns off to show that the air conditioning mode has been canceled. On hot days, open the windows long enough to let hot inside air escape. This helps to reduce the time it takes for the vehicle to cool down. It also helps the system to operate more efficiently. The air conditioning system removes moisture from the air, so a small amount of water might drip underneath the vehicle while idling or after turning off the engine. This is normal. 3-30 The solar sensor, located in the defrost grille, in the middle of the instrument panel, monitors the solar radiation. Do not cover the solar sensor or the system will not work properly. The interior temperature sensor, located in the headliner, measures the temperature of the air inside the vehicle. There is also an exterior temperature sensor located behind the front grille. This sensor reads the outside air temperature and helps maintain the temperature inside the vehicle. Any cover on the front of the vehicle could cause a false reading in the displayed temperature on the rearview mirror. The climate control system uses the information from these sensors to maintain your comfort setting by adjusting the outlet temperature, fan speed, and the air delivery mode. The system may also supply cooler air to the side of the vehicle facing the sun. The recirculation mode will also be used as needed to maintain cool outlet temperatures. Defogging and Defrosting Fog on the inside of the windows is a result of high humidity (moisture) condensing on the cool window glass. This can be minimized if the climate control system is used properly. There are two modes to clear fog or frost from the windshield. Use H and G to select the defog or defrost modes. - (Defog): Press this button to clear the windows of fog or moisture and warm the passengers. This mode directs air to the windshield, ﬂoor outlets, and side window vents. When this mode is selected, the system turns off recirculation and runs the air conditioning compressor unless the outside temperature is close to freezing. The recirculation mode cannot be selected while in the defog mode. Do not drive the vehicle until all the windows are clear. 0 (Defrost): Press this button to remove fog or frost from the windshield more quickly. This mode directs a portion of the air to the windshield and side window vents and some to the ﬂoor vents. In this mode, the system will automatically force outside air into your vehicle. The recirculation mode cannot be selected while in the defrost mode. The air conditioning compressor will run automatically in this setting, unless the outside temperature is close to freezing. Do not drive the vehicle until all the windows are clear. 3-31 Rear Window Defogger The rear window defogger uses a warming grid to remove fog from the rear window. <(Rear Window Defogger): If your vehicle has this feature, press this button to turn the defogger on or off. It automatically turns off several minutes after it has been activated. The defogger can also be turned off by turning the engine off. Do not drive the vehicle until all the windows are clear. Notice: Do not use a razor blade or sharp object to clear the inside rear window. Do not adhere anything to the defogger grid lines in the rear glass. These actions may damage the rear defogger. Repairs would not be covered by your warranty. Heated Mirrors: If your vehicle has heated outside rearview mirrors, the mirrors will heat to help clear fog or frost from the surface of the mirror when the rear window defog button is pressed. See Outside Power Mirrors on page 2-39. Outlet Adjustment Use the air outlets located in the center and on the side of the instrument panel to direct the airﬂow. Operation Tips (cid:129) Clear away any ice, snow, or leaves from air inlets at the base of the windshield that could block the ﬂow of air into your vehicle. (cid:129) Keep the path under the front seats clear of objects to help circulate the air inside of the vehicle more effectively. (cid:129) Use of non-GM approved hood deﬂectors can adversely affect the performance of the system. Check with your dealer/retailer before adding equipment to the outside of your vehicle. 3-32 Warning Lights, Gages, and Indicators This part describes the warning lights and gages on your vehicle. The pictures help to locate them. Warning lights and gages can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement. Paying attention to the warning lights and gages could also save you or others from injury. Warning lights come on when there may be or is a problem with one of your vehicle’s functions. As the details show on the next few pages, some warning lights come on brieﬂy when you start the engine just to let you know they are working. If you are familiar with this section, you should not be alarmed when this happens. Gages can indicate when there may be or is a problem with one of your vehicle’s functions. Often gages and warning lights work together to let you know when there is a problem with your vehicle. When one of the warning lights comes on and stays on as you are driving, or when one of the gages shows there may be a problem, check the section that tells you what to do about it. Please follow this manual’s advice. Waiting to do repairs can be costly and even dangerous. So please get to know your vehicle’s warning lights and gages. They can be a big help. Your vehicle also has a Driver Information Center (DIC) that works along with warning lights and gages. See DIC Warnings and Messages on page 3-59 for more information. 3-33 Instrument Panel Cluster Your instrument panel cluster is designed to let you know at a glance how your vehicle is running. You will know how fast you are going, about how much fuel you have and many other things you’ll need to know to drive safely and economically. United States version shown, Canada similar 3-34 Speedometer and Odometer Your speedometer lets you see your speed in both miles per hour (mph) and kilometers per hour (km/h). Your odometer shows how far your vehicle has been driven, in either miles (used in the United States) or kilometers (used in Canada). Engine Hour Meter Display The Driver Information Center (DIC) can also display the number of hours the engine has run. To display the engine hours, turn the ignition off, press and hold the reset button for at least four seconds. The hour meter will be displayed for up to 30 seconds, or until the ignition is turned on. See DIC Operation and Displays (Using DIC Buttons) on page 3-52 or DIC Operation and Displays (Using Trip Odometer Reset Stem) on page 3-58 for more information. Trip Odometer The trip odometer can tell you how far your vehicle has been driven since you last set the trip odometer to zero. Press the reset button, located on the instrument panel cluster next to the voltmeter, to toggle between the trip odometer and the regular odometer. Holding the reset button for approximately one second while the trip odometer is displayed will reset it. To display the odometer reading with the ignition off, press the reset button. See DIC Operation and Displays (Using DIC Buttons) on page 3-52 or DIC Operation and Displays (Using Trip Odometer Reset Stem) on page 3-58 for more information. Tachometer Your tachometer displays the engine speed in revolutions per minute (rpm). See “Grade Braking (Allison Transmission®)” under Tow/Haul Mode on page 2-31 for more information. Notice: tachometer in the solid red area, your vehicle could be damaged. The damages would not be covered by your warranty. Do not operate the engine in the solid red area. If you operate the engine with the 3-35 Safety Belt Reminders Safety Belt Reminder Light When the engine is started, a chime will sound for several seconds to remind people to buckle their safety belts. The driver safety belt light will also come on and stay on for several seconds, then it will ﬂash for several more. You should buckle your seat belt. Passenger Safety Belt Reminder Light Several seconds after the engine is started, a chime will sound for several seconds to remind the front passenger to buckle their safety belt. This would only occur if the passenger airbag is enabled. See Passenger Sensing System on page 1-63 for more information. The passenger safety belt light will also come on and stay on for several seconds, then it will ﬂash for several more. This chime and light will be repeated if the driver remains unbuckled and the vehicle is in motion. This chime and light are repeated if the passenger remains unbuckled and the vehicle is in motion. If the passenger’s safety belt is buckled, neither the chime nor the light will come on. See DIC Warnings and Messages on page 3-59 for more information on driver and passenger safety belt reminders. If the driver’s belt is buckled, neither the chime nor the light will come on. See Passenger Sensing System on page 1-63 for more information. 3-36 Airbag Readiness Light There is an airbag readiness light on the instrument panel cluster, which shows the airbag symbol. The system checks the airbag’s electrical system for malfunctions. The light tells you if there is an electrical problem. The system check includes the airbag sensor, the pretensioners, the airbag modules, the wiring and the crash sensing and diagnostic module. For more information on the airbag system, see Airbag System on page 1-54. This light will come on when you start your vehicle, and it will ﬂash for a few seconds. The light should go out and the system is ready. If the airbag readiness light stays on after you start the vehicle or comes on when you are driving, your airbag system may not work properly. Have your vehicle serviced right away. {CAUTION: If the airbag readiness light stays on after you start your vehicle, it means the airbag system may not be working properly. The airbags in your vehicle may not inﬂate in a crash, or they could even inﬂate without a crash. To help avoid injury to yourself or others, have your vehicle serviced right away if the airbag readiness light stays on after you start your vehicle. The airbag readiness light should ﬂash for a few seconds when you start the engine. If the light does not come on then, have it ﬁxed immediately. If there is a problem with the airbag system, an airbag Driver Information Center (DIC) message may also come on. See DIC Warnings and Messages on page 3-59 for more information. 3-37 Passenger Airbag Status Indicator Your vehicle has the passenger sensing system. Your overhead console has a passenger airbag status indicator. United States Canada When you start the vehicle, the passenger airbag status indicator will light ON and OFF, or the symbol for on and off, for several seconds as a system check. Then, after several more seconds, the status indicator will light either ON or OFF, or either the on or off symbol to let you know the status of the right front passenger’s frontal airbag. If the word ON or the on symbol is lit on the passenger airbag status indicator, it means that the right front passenger’s frontal airbag is enabled (may inﬂate). {CAUTION: If the on indicator comes on when you have a rear-facing child restraint installed in the right front passenger’s seat, it means that the passenger sensing system has not turned off the passenger’s frontal airbag. A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger’s airbag inﬂates. This is because the back of the rear-facing child restraint would be very close to the inﬂating airbag. Do not use a rear-facing child restraint in the right front passenger’s seat if the airbag is turned on. 3-38 {CAUTION: Even though the passenger sensing system is designed to turn off the right front passenger’s frontal airbag if the system detects a rear-facing child restraint, no system is fail-safe, and no one can guarantee that an airbag will not deploy under some unusual circumstance, even though it is turned off. We recommend that rear-facing child restraints be secured in the rear seat, even if the airbag is off. If the word OFF or the off symbol is lit on the airbag status indicator, it means that the passenger sensing system has turned off the right front passenger’s frontal airbag. See Passenger Sensing System on page 1-63 for more on this, including important safety information. If, after several seconds, both status indicator lights remain on, or if there are no lights at all, there may be a problem with the lights or the passenger sensing system. See your dealer/retailer for service. {CAUTION: If the airbag readiness light in the instrument panel cluster ever comes on and stays on, it means that something may be wrong with the airbag system. If this ever happens, have the vehicle serviced promptly, because an adult-size person sitting in the right front passenger’s seat may not have the protection of the airbag(s). See Airbag Readiness Light on page 3-37 for more on this, including important safety information. 3-39 Charging System Light Voltmeter Gage This light will come on brieﬂy when you turn on the ignition, but the engine is not running, as a check to show you it is working. When your engine is not running, but the ignition is on, this gage shows the battery’s state of charge in DC volts. It should go out once the engine is running. If it stays on, or comes on while you are driving, you may have a problem with the charging system. A charging system Driver Information Center (DIC) message may also appear. See DIC Warnings and Messages on page 3-59 for more information. This light could indicate that you have problems with a generator drive belt, or another electrical problem. Have it checked right away. If you must drive a short distance with the light on, be certain to turn off all your accessories, such as the radio and air conditioner. When the engine is running, the gage shows the condition of the charging system. The gage may transition from a higher to lower or a lower to higher reading, this is normal. Readings between the low and high warning zones indicate the normal operating range. 3-40 Readings in the low warning zone may occur when a large number of electrical accessories are operating in the vehicle and the engine is left at an idle for an extended period. This condition is normal since the charging system is not able to provide full power at engine idle. As engine speeds are increased, this condition should correct itself as higher engine speeds allow the charging system to create maximum power. You can only drive for a short time with the reading in either warning zone. If you must drive, turn off all unnecessary accessories. Readings in either warning zone indicate a possible problem in the electrical system. Have the vehicle serviced as soon as possible. Brake System Warning Light With the ignition on, the brake system warning light will come on when you set the parking brake. If you try to drive with the parking brake engaged, a chime will sound when the vehicle speed is greater than 5 mph (8 km/h). Your vehicle’s hydraulic brake system is divided into two parts. If one part is not working, the other part can still work and stop you. For good braking, though, you need both parts working well. If the warning light comes on and a chime sounds there could be a brake problem. Have your brake system inspected right away. This light may also come on due to low brake ﬂuid. See Brakes on page 5-36 for more information. United States Canada 3-41 This light should come on brieﬂy when you turn the ignition key to RUN. If it does not come on then, have it ﬁxed so it will be ready to warn you if there is a problem. {CAUTION: Your brake system may not be working properly if the brake system warning light is on. Driving with the brake system warning light on can lead to an accident. If the light is still on after you have pulled off the road and stopped carefully, have the vehicle towed for service. If the light comes on while you are driving, pull off the road and stop carefully. You may notice that the pedal is harder to push or may go closer to the ﬂoor. It may take longer to stop. If the light is still on, have the vehicle towed for service. See Towing Your Vehicle on page 4-41. 3-42 Antilock Brake System Warning Light For vehicles with the Antilock Brake System (ABS), this light will come on brieﬂy when you start the engine. That is normal. If the light does not come on then, have it ﬁxed so it will be ready to warn you if there is a problem. If the ABS light stays on, turn the ignition off, if the light comes on when you are driving, stop as soon as it is safely possible and turn the ignition off. Then start the engine again to reset the system. If the ABS light still stays on, or comes on again while you are driving, your vehicle needs service. If the regular brake system warning light is not on, you still have brakes, but you do not have antilock brakes. If the regular brake system warning light is also on, you do not have antilock brakes and there is a problem with your regular brakes. See Brake System Warning Light on page 3-41 For vehicles with a Driver Information Center (DIC), see DIC Warnings and Messages on page 3-59 for all brake related DIC messages. StabiliTrak® Indicator Light Engine Coolant Temperature Gage If equipped, this warning light should come on brieﬂy when the engine is started. If the warning light does not come on then, have it ﬁxed so it will be ready to warn you if there is a problem. If it stays on, or comes on when you are driving, there may be a problem with your StabiliTrak® system and your vehicle may need service. When this warning light is on, the system is off and will not limit wheel spin. Adjust your driving accordingly. This light will also ﬂash when the StabiliTrak® system is active. If the StabiliTrak® system warning light comes on and stays on for an extended period of time when the system is turned on, your vehicle needs service. See StabiliTrak® System on page 4-5 for more information. United States Canada This gage shows the engine coolant temperature. It also provides an indicator of how hard your vehicle is working. During a majority of the operation, the gage will read 210°F (100°C) or less. If you are pulling a load or going up hills, it is normal for the temperature to ﬂuctuate and go over the 235°F (113°C) mark. If the gage reaches the 260°F (125°C) mark, it indicates that the cooling system is working beyond its capacity. See Engine Overheating on page 5-26. 3-43 Tire Pressure Light This light comes on brieﬂy when the engine is started. This light will also come on when one or more of your tires are signiﬁcantly underinﬂated. A tire pressure message in the Driver Information Center (DIC), may accompany the light. See DIC Warnings and Messages on page 3-59 for more information. Stop and check your tires as soon as it is safe to do so. If underinﬂated, inﬂate to the proper pressure. See Tires on page 5-58 for more information. If a problem is detected with the Tire Pressure Monitor System, this light will ﬂash for approximately 60 seconds and then stay on solid for the remainder of the ignition cycle. See Tire Pressure Monitor System on page 5-66 for more information. 3-44 Malfunction Indicator Lamp Check Engine Light A computer system called OBD II (On-Board Diagnostics-Second Generation) monitors operation of the fuel, ignition, and emission control systems. It makes sure that emissions are at acceptable levels for the life of the vehicle, helping to produce a cleaner environment. The check engine light comes on to indicate that there is an OBD II problem and service is required. Malfunctions often are indicated by the system before any problem is apparent. This can prevent more serious damage to your vehicle. This system is also designed to assist your service technician in correctly diagnosing any malfunction. If you keep driving your vehicle with this Notice: light on, after a while, the emission controls might not work as well, your vehicle’s fuel economy might not be as good, and the engine might not run as smoothly. This could lead to costly repairs that might not be covered by your warranty. Notice: Modiﬁcations made to the engine, transmission, exhaust, intake, or fuel system of your vehicle or the replacement of the original tires with other than those of the same Tire Performance Criteria (TPC) can affect your vehicle’s emission controls and can cause this light to come on. Modiﬁcations to these systems could lead to costly repairs not covered by your warranty. This could also result in a failure to pass a required Emission Inspection/Maintenance test. See Accessories and Modiﬁcations on page 5-3. This light comes on, as a check to show it is working, when the ignition is turned ON/RUN but the engine is not running. If the light does not come on, have it repaired. This light also comes on during a malfunction in one of two ways: Light Flashing — A misﬁre condition has been detected. A misﬁre increases vehicle emissions and could damage the emission control system on your vehicle. Diagnosis and service might be required. Light On Steady — An emission control system malfunction has been detected on your vehicle. Diagnosis and service might be required. 3-45 (cid:129) (cid:129) If the Light is Flashing The following can prevent more serious damage to your vehicle: (cid:129) Reduce vehicle speed. (cid:129) Avoid hard accelerations. (cid:129) Avoid steep uphill grades. If you are towing a trailer, reduce the amount of cargo being hauled as soon as it is possible. If the light stops ﬂashing and remains on steady, see “If the Light Is On Steady” following. If the light continues to ﬂash, when it is safe to do so, stop the vehicle. Find a safe place to park the vehicle. Turn the ignition off, wait at least 10 seconds, and restart the engine. If the light remains on steady, see “If the Light Is On Steady” following. If the light is still ﬂashing, follow the previous steps and see your dealer/retailer for service as soon as possible. If the Light Is On Steady You might be able to correct the emission system malfunction by considering the following: Did you recently put fuel into your vehicle? If so, reinstall the fuel cap, making sure to fully install the cap. See Filling the Tank on page 5-8. The diagnostic system can determine if the fuel cap has been left off or improperly installed. A loose or missing fuel cap allows fuel to evaporate into the atmosphere. A few driving trips with the cap properly installed should turn the light off. Did you just drive through a deep puddle of water? If so, your vehicle’s electrical system might be wet. The condition is usually corrected when the electrical system dries out. A few driving trips should turn the light off. 3-46 (cid:129) Have you recently changed brands of fuel? If so, be sure to fuel your vehicle with quality fuel. See Gasoline Octane on page 5-5. Poor fuel quality causes the engine not to run as efficiently as designed. You might notice this as stalling after start-up, stalling when you put the vehicle into gear, misﬁring, hesitation on acceleration, or stumbling on acceleration — these conditions might go away once the engine is warmed up. This will be detected by the system and cause the light to turn on. If you experience one or more of these conditions, change the fuel brand you use. It will require at least one full tank of the proper fuel to turn the light off. If none of the above steps have made the light turn off, your dealer/retailer can check the vehicle. Your dealer/retailer has the proper test equipment and diagnostic tools to ﬁx any mechanical or electrical problems that might have developed. Emissions Inspection and Maintenance Programs Some state/provincial and local governments have or might begin programs to inspect the emission control equipment on your vehicle. Failure to pass this inspection could prevent you from getting a vehicle registration. Here are some things you need to know to help your vehicle pass an inspection: Your vehicle will not pass this inspection if the check engine light is on or not working properly. Your vehicle will not pass this inspection if the OBD (on-board diagnostic) system determines that critical emission control systems have not been completely diagnosed by the system. The vehicle would be considered not ready for inspection. This can happen if you have recently replaced the battery or if the battery has run down. The diagnostic system is designed to evaluate critical emission control systems during normal driving. This can take several days of routine driving. If you have done this and your vehicle still does not pass the inspection for lack of OBD system readiness, your dealer/retailer can prepare the vehicle for inspection. 3-47 A reading in the low pressure zone may be caused by a dangerously low oil level or some other problem causing low oil pressure. Check your oil as soon as possible. See DIC Warnings and Messages on page 3-59 and Engine Oil on page 5-13. {CAUTION: Do not keep driving if the oil pressure is low. If you do, your engine can become so hot that it catches ﬁre. You or others could be burned. Check your oil as soon as possible and have your vehicle serviced. Notice: Lack of proper engine oil maintenance may damage the engine. The repairs would not be covered by your warranty. Always follow the maintenance schedule in this manual for changing engine oil. Oil Pressure Gage United States Canada The oil pressure gage shows the engine oil pressure in psi (pounds per square inch) when the engine is running. Canadian vehicles indicate pressure in kPa (kilopascals). Oil pressure may vary with engine speed, outside temperature and oil viscosity, but readings above the low pressure zone indicate the normal operating range. 3-48 Oil Pressure Light {CAUTION: Do not keep driving if the oil pressure is low. If you do, your engine can become so hot that it catches ﬁre. You or others could be burned. Check your oil as soon as possible and have your vehicle serviced. Notice: Lack of proper engine oil maintenance may damage the engine. The repairs would not be covered by your warranty. Always follow the maintenance schedule in this manual for changing engine oil. This light will come on brieﬂy when you start your engine. If it does not, have your vehicle serviced. When the light comes on and stays on, it means that oil is not ﬂowing through your engine properly. You could be low on oil and you might have some other system problem. Security Light This light ﬂashes when the vehicle security system is activated. 3-49 Fog Lamp Light Highbeam On Light The fog lamp light will come on when the fog lamps are in use. This light comes on when the high-beam headlamps are in use. The light will go out when the fog lamps are turned off. See Fog Lamps on page 3-17 for more information. Cruise Control Light See Headlamp High/Low-Beam Changer on page 3-8 for more information. Tow/Haul Mode Light This light comes on whenever you set the cruise control. This light comes on when the Tow/Haul mode has been activated. The light goes out when the cruise control is turned off. See Cruise Control on page 3-11 for more information. For more information, see Tow/Haul Mode on page 2-31. 3-50 Fuel Gage United States Canada When the ignition is on, the fuel gage tells you about how much fuel you have left in your tank. The gage will ﬁrst indicate empty before you are out of fuel, and you should get more fuel as soon as possible. Here are some situations you may experience with your fuel gage. None of these indicate a problem with the fuel gage. (cid:129) At the gas station, the fuel pump shuts off before the gage reads full. It takes a little more or less fuel to ﬁll up than the fuel gage indicated. For example, the gage may have indicated the tank was half full, but it actually took a little more or less than half the tank’s capacity to ﬁll the tank. The gage goes back to empty when you turn off the ignition. 3-51 (cid:129) (cid:129) Driver Information Center (DIC) Your vehicle has a Driver Information Center (DIC). The DIC displays information about your vehicle. It also displays warning messages if a system problem is detected. All messages will appear in the DIC display located below the tachometer in the instrument panel cluster. The DIC comes on when the ignition is on. After a short delay, the DIC will display the information that was last displayed before the engine was turned off. For the displays available using DIC buttons, see “DIC Operation and Displays (Using DIC Buttons)” later in this section and DIC Vehicle Customization (With DIC Buttons) on page 3-68. For the displays available using the trip odometer reset stem, see “DIC Operation and Displays (Using Trip Odometer Reset Stem)” later in this section. DIC Operation and Displays (Using DIC Buttons) The DIC has different displays which can be accessed by pressing the DIC buttons located on the instrument panel, next to the steering wheel. The DIC displays trip, fuel, and vehicle system information, and warning messages if a system problem is detected. The DIC also allows some features to be customized. See DIC Vehicle Customization (With DIC Buttons) on page 3-68 for more information. You can also use the trip odometer reset stem to view some of the DIC displays. See ″DIC Operation and Displays (Using Trip Odometer Reset Stem)″ later in this section. 3-52 DIC Buttons The buttons are the trip/fuel, vehicle information, customization, and set/reset buttons. The button functions are detailed in the following pages. 3 (Trip/Fuel): Press this button to display the odometer, trip odometer, fuel range, average economy, fuel used, timer, and transmission temperature. T (Vehicle Information): Press this button to display the oil life, units, tire pressure readings, engine hours, and Remote Keyless Entry (RKE) transmitter programming. U (Customization): Press this button to customize the feature settings on your vehicle. See DIC Vehicle Customization (With DIC Buttons) on page 3-68 for more information. V (Set/Reset): Press this button to set or reset certain functions and to turn off or acknowledge messages on the DIC. Trip/Fuel Menu Items 3(Trip/Fuel): Press this button to scroll through the following menu items: Odometer Press the trip/fuel button until ODOMETER displays. This display shows the distance the vehicle has been driven in either miles (mi) or kilometers (km). Pressing the trip odometer reset stem will also display the odometer. To switch between English and metric measurements, see “Units” later in this section. 3-53 Trip Odometer Press the trip/fuel button until TRIP displays. This display shows the current distance traveled in either miles (mi) or kilometers (km) since the last reset for the trip odometer. Pressing the trip odometer reset stem will also display the trip odometer. The trip odometer can be reset to zero by pressing the set/reset button while the trip odometer is displayed. You can also reset the trip odometer while it is displayed by pressing and holding the trip odometer reset stem. The trip odometer has a feature called the retro-active reset. This can be used to set the trip odometer to the number of miles (kilometers) driven since the ignition was last turned on. This can be used if the trip odometer is not reset at the beginning of the trip. To use the retro-active reset feature, press and hold the set/reset button for at least four seconds. The trip odometer will display the number of miles (mi) or kilometers (km) driven since the ignition was last turned on and the vehicle was moving. Once the vehicle begins moving, the trip odometer will accumulate mileage. For example, if the vehicle was driven 5 miles (8 km) before it is started again, and then the retro-active reset feature is activated, the display will show 5 miles (8 km). As the vehicle begins moving, the display will then increase to 5.1 miles (8.2 km), 5.2 miles (8.4 km), etc. 3-54 Fuel Range Press the trip/fuel button until FUEL RANGE displays. This display shows the approximate number of remaining miles (mi) or kilometers (km) the vehicle can be driven without refueling. The display will show LOW if the fuel level is low. The fuel range estimate is based on an average of the vehicle’s fuel economy over recent driving history and the amount of fuel remaining in the fuel tank. This estimate will change if driving conditions change. For example, if driving in traffic and making frequent stops, this display may read one number, but if the vehicle is driven on a freeway, the number may change even though the same amount of fuel is in the fuel tank. This is because different driving conditions produce different fuel economies. Generally, freeway driving produces better fuel economy than city driving. Fuel range cannot be reset. Average Economy Press the trip/fuel button until AVG ECONOMY displays. This display shows the approximate average miles per gallon (mpg) or liters per 100 kilometers (L/100 km). This number is calculated based on the number of mpg (L/100 km) recorded since the last time this menu item was reset. To reset AVG ECONOMY, press and hold the set/reset button. Fuel Used Press the trip/fuel button until FUEL USED displays. This display shows the number of gallons (gal) or liters (L) of fuel used since the last reset of this menu item. To reset the fuel used information, press and hold the set/reset button while FUEL USED is displayed. Timer Press the trip/fuel button until TIMER displays. This display can be used as a timer. To start the timer, press the set/reset button while TIMER is displayed. The display will show the amount of time that has passed since the timer was last reset, not including time the ignition is off. Time will continue to be counted as long as the ignition is on, even if another display is being shown on the DIC. The timer will record up to 99 hours, 59 minutes and 59 seconds (99:59:59) after which the display will return to zero. To stop the timer, press the set/reset button brieﬂy while TIMER is displayed. To reset the timer to zero, press and hold the set/reset button while TIMER is displayed. Transmission Temperature Press the trip/fuel button until TRANS TEMP displays. This display shows the temperature of the automatic transmission ﬂuid in either degrees Fahrenheit (°F) or degrees Celsius (°C). Blank Display This display shows no information. 3-55 Vehicle Information Menu Items T (Vehicle Information): Press this button to scroll through the following menu items: Oil Life Press the vehicle information button until OIL LIFE REMAINING displays. This display shows an estimate of the oil’s remaining useful life. If you see 99% OIL LIFE REMAINING on the display, that means 99% of the current oil life remains. The engine oil life system will alert you to change the oil on a schedule consistent with your driving conditions. When the remaining oil life is low, the CHANGE ENGINE OIL SOON message will appear on the display. See “CHANGE ENGINE OIL SOON” under DIC Warnings and Messages on page 3-59. You should change the oil as soon as you can. See Engine Oil on page 5-13. In addition to the engine oil life system monitoring the oil life, additional maintenance is recommended in the Maintenance Schedule in this manual. See Scheduled Maintenance on page 6-4 for more information. Remember, you must reset the OIL LIFE display yourself after each oil change. It will not reset itself. Also, be careful not to reset the OIL LIFE display accidentally at any time other than when the oil has just been changed. It cannot be reset accurately until the next oil change. To reset the engine oil life system, see Engine Oil Life System on page 5-16. Units Press the vehicle information button until UNITS displays. This display allows you to select between English or Metric units of measurement. Once in this display, press the set/reset button to select between ENGLISH or METRIC units. All of the vehicle information will then be displayed in the unit of measurement selected. Tire Pressure The pressure for each tire can be viewed in the DIC. The tire pressure will be shown in either pounds per square inch (psi) or kilopascals (kPa). Press the vehicle information button until the DIC displays FRONT TIRES PSI (kPa) LEFT ## RIGHT ##. Press the vehicle information button again until the DIC displays REAR TIRES PSI (kPa) LEFT ## RIGHT ##. 3-56 If a low or high tire pressure condition is detected by the system while driving, a message advising you to check the pressure in a speciﬁc tire will appear in the display. See Inﬂation - Tire Pressure on page 5-65 and DIC Warnings and Messages on page 3-59 for more information. If the tire pressure display shows dashes instead of a value, there may be a problem with your vehicle. If this consistently occurs, see your dealer/retailer for service. Engine Hours Press the vehicle information button until ENGINE HOURS displays. This display shows the total number of hours the engine has run. Relearn Remote Key This display allows you to match Remote Keyless Entry (RKE) transmitters to your vehicle. To match an RKE transmitter to your vehicle: 1. Press the vehicle information button until PRESS V TO RELEARN REMOTE KEY displays. 2. Press the set/reset button until REMOTE KEY LEARNING ACTIVE is displayed. 3. Press and hold the lock and unlock buttons on the ﬁrst transmitter at the same time for about 15 seconds. On vehicles with memory recall seats, the ﬁrst transmitter learned will match driver 1 and the second will match driver 2. A chime will sound indicating that the transmitter is matched. 4. To match additional transmitters at this time, repeat Step 3. Each vehicle can have a maximum of eight transmitters matched to it. 5. To exit the programming mode, you must cycle the key to LOCK/OFF. Blank Display This display shows no information. 3-57 DIC Operation and Displays (Using Trip Odometer Reset Stem) The DIC has different displays which can be accessed by pressing the trip odometer reset stem located on the instrument panel cluster. Pressing the trip odometer reset stem will also turn off, or acknowledge, DIC messages. You can use the trip odometer reset stem to view the following displays: odometer, engine hours, trip odometer, transmission temperature, and display language. Trip Odometer Reset Stem Menu Items Odometer Press the trip odometer reset stem until ODOMETER displays. This display shows the distance the vehicle has been driven in either miles (mi) or kilometers (km). Engine Hours To display the ENGINE HOURS, place the ignition in LOCK/OFF or ACC/ACCESSORY, then press and hold the trip odometer reset stem for four seconds while viewing the ODOMETER. This display shows the total number of hours the engine has run. Trip Odometer Press the trip odometer reset stem until TRIP displays. This display shows the current distance traveled in either miles (mi) or kilometers (km) since the last reset for the trip odometer. The trip odometer can be reset to zero by pressing and holding the trip odometer reset stem while the trip odometer is displayed. The trip odometer has a feature called the retro-active reset. This can be used to set the trip odometer to the number of miles (kilometers) driven since the ignition was last turned on. This can be used if the trip odometer is not reset at the beginning of the trip. To use the retro-active reset feature, press and hold the trip odometer reset stem for at least four seconds. The trip odometer will display the number of miles (mi) or kilometers (km) driven since the ignition was last turned on and the vehicle was moving. Once the vehicle begins moving, the trip odometer will accumulate mileage. For example, if the vehicle was driven 5 miles (8 km) before it is started again, and then the retro-active reset feature is activated, the display will show 5 miles (8 km). As the vehicle begins moving, the display will then increase to 5.1 miles (8.2 km),

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2008 GMC Sierra Owners Manual