1996 GMC Savana Owners Manual

grades, they must also conform to Federal safety requirements and additional General Motors Tire Performance Criteria (TYC) standards.

6-46

Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and a half (1 1/2) times as well on the governrnent course as a tire b oraded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due t o variations in driving habits, service practices and differences in road characteristics and climate.

Traction -- A, B, C

The traction grades, from highest to lowest, are A, B, and C, and they represent the tire's ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction pelformance. Warning: The traction grade assigned to this tire is based on braking (straightahead) traction tests and does not include cornering (turning) traction.

Temperature -- A, B, C

The temperature grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law. Warning: The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can c a ~ w heat. buildup and possible tire failure.

6-47

Wheel Alignment and Tire Balance The wheels on your vehicle were aligned and balanced carefully at the factory to give you the longest tire life and best overall performance. In most cases, you will not need to have your wheels aligned again. However, if you notice unusual tire wear or your vehicle pulling one way or the other, the alignment may need to be reset. If you notice your vehicle vibrating when driving on a smooth road, your wheels may need to be rebalanced. Wheel Replacement Replace any wheel that is bent, cracked, or badly rusted or corroded. If wheel nuts keep coming loose, the wheel, wheel bolts and wheel nuts should be replaced. If the wheel leaks air, replace it (except some aluminum wheels, which can sometimes be repaired). See your GM dealer if any of these conditions exist. Your dealer will know the kind of wheel you need.

Each new wheel should have the same load-carrying capacity, diameter, width, offset and be mounted the same way as the one it replaces. If you need to replace any of your wheels, wheel bolts or wheel nuts, replace them only with new GM original equipment parts. This way, you will be sure to have the right wheel, wheel bolts and wheel nuts for your vehicle.

4 CAUTION:

r-

Using the wrong replacement wheels, wheel bolts or wheel nuts on your vehicle can be dangerous. It could affect the braking and handling of your vehicle, make your tires lose air and make you lose control. You could have a collision in which you or others could be injured. Always use the correct wheel, wheel bolts and wheel nuts for replacement.

6-48

NOTICE:

The wrong wheel can also cause problems with bearing life, brake cooling, speedometer or odometer calibration, headlamp aim, bumper height, vehicle ground clearance and tire or tire chain clearance to the body and chassis.

Whenever a wheel, wheel bolt or wheel nut is replaced on a dual wheel setup, check the wheel nut torque after 100, 1,000 and 6,000 miles (160, 1 600 and 10 000 km) of driving. For proper torque, see “Wheel Nut Torque” in the Index. See “Changing a Flat Tire” in the Index for more information.

Used Replacement Wheels

Putting a used wheel on your vehicle is dangerous. You can’t know how it’s been used or how many miles it’s been driven. It could fail suddenly and cause an accident. If you have to replace a wheel, use a new GM original equipment wheel.

6-49

Tire Chains

NOTICE:

Use tire chains only where legal and only when you must. Use chains that are the proper size for your tires. Install them on the tires of the rear axle. Tighten them as tightly as possible with the ends securely fastened. Drive slowly and follow the chain manufacturer's instructions. If you can hear the chains contacting your vehicle, stop and retighten them. If the contact continues, slow down until it stops. Driving too fast or spinning the wheels with I chains on will damage your vehicle. Appearance Care Remember, cleaning products can be hazardous. Some are toxic. Others can burst into flame if you strike a match or get them on a hot part of the vehicle. Some are dangerous if you breathe their fumes i n a closed space. When you use anything from a container to clean your vehicle, be sure to follow the n1anufacturer's warnings and instructions. And always open your doors or windows when you're cleaning the inside. 6-50

0 Gasoline 0 Benzene Naphtha

0 Carbon Tetrachloride 0 Acetone 0 Paint Thinner 0 Turpentine 0 Lacquer Thinner 0 Nail Polish Remover They can all be hazardous -- some Inore than others -- and they can all damage your vehicle, too. Don't use any of these unless this manual says you can. In many uses, these will darnage your vehicle: 0 Alcohol 0 Laundry Soap 0 Bleach 0 Reducing Agents

Cleaning the Inside of Your Vehicle Use a vacuum cleaner often to get rid of dust and loose dirt. Wipe vinyl or leather with a clean, damp cloth. Your CM dealer has two GM cleaners, a solvent-type spot lifter and a foam-type powdered cleaner. They will clean normal spots and stains very well. Do not use them on vinyl or leather. Here are some cleaning tips:

Always read the instructions on the cleaner label. Clean up stains as soon as you can -- before they set. Use a clean cloth or sponge, and change to a clean area often. A soft brush may be used if stains are stubborn. Use solvent-type cleaners in a well-ventilated area only. If you use them, don’t saturate the stained area. If a ring forms after spot cleaning, clean the entire area immediately or it will set.

2.

3.

Using Foam-Type Cleaner on Fabric Vacuum and brush the area to remove any 1. loose dirt. Always clean a whole trim panel or section. Mask surrounding trim along stitch or welt lines. Mix Multi-Purpose Powdered Cleaner following the directions on the container label. Use suds only and apply with a clean sponge. Don’t saturate the material. Don’t rub it roughly. As soon as you’ve cleaned the section, use a sponge to remove the suds. Rinse the section with a clean, wet sponge. Wipe off what’s left with a slightly damp paper towel or cloth. Then dry it immediately with a blow dryer. Wipe with a clean cloth.

4. 5. 6. 7.

10. 11.

8. 9.

6-51

Special Cleaning Problems Greasy or Oily Stains Stains caused by grease, oil, butter, margarine, shoe polish, coffee with cream, chewing gum, cosmetic creams, vegetable oils, wax crayon, tar and asphalt can be removed as follows: I . Carefully scrape off excess stain. 2. Follow the solvent-type instructions described earlier. 3. Shoe polish, wax crayon, tar and asphalt will stain if

left on a vehicle’s seat fabric. They should be removed as soon as possible. Be careful, because the cleaner will dissolve them and may cause them to spread.

Using Solvent-Type Cleaner on Fabric First, see if you have to use solvent-type cleaner at all. Some spots and stains will clean off better with just water and mild soap. If you need to use a solvent: 0 Gently scrape excess soil from the trim material with a clean, dull knife or scraper. Use very little cleaner, light pressure and clean cloths (preferably cheesecloth). Cleaning should start at the outside of the stain, “feathering” toward the center. Keep changing to a clean section of the cloth. When you clean a stain from fabric, immediately dry the area with a blow dryer to help prevent a cleaning ring.

Fabric Protection Your GM has upholstery and carpet that has been treated with Scotchgard” Fabric Protector, a 3M product. It protects fabrics by repelling oil and water, which are the carriers of most stains. Even with this protection, you still need to clean your upholstery and carpet often to keep it looking new. Further information on cleaning is available by calling 1-800-433-3296 (in Minnesota, 1-800-642-6 167).

6-52

, .~

Non-Greasy Stains Stains caused by catsup, coffee (black), egg, fruit, fruit juice, milk, soft drinks, wine, vomit, urine and blood can be removed as follows: 1. Carefully scrape oiYexcess stain, then sponge the

soiled area with cool water.

2. If a stain remains, follow the foam-type instructions

described earlier.

3. If an odor lingers after cleaning vomit or urine, treat

the area with a watedbaking soda solution: 1 teaspoon (5 mlj of baking soda to 1 cup (250 ml) of lukewarm water.

4. If needed, clean lightly with solvent-type cleaner.

Combination Stains Stains caused by candy, ice cream, mayonnaise, chili sauce and unknown stains can be removed as follows:

Carefully scrape off excess stain, then clean with cool water and allow to dry. If a stain remains, clean it with solvent-type cleaner.

Cleaning Vinyl Use warm water and a clean cloth. 0 Rub with a clean, damp cloth to remove dirt. You

may have to do it more than once.

0 Things like tar, asphalt and shoe polish will stain if

you don't get them off quickly. Use a clean cloth and a GM VinyVLeather Cleaner or equivalent product.

Cleaning LC ther Use a soft cloth with lukewarm waler and a mild soap or saddle soap.

For stubborn stains, use a GM VinyVLeather Cleaner or equivalent product. Never. use oils, varnishes, solvent-based or abrasive cleaners, furniture polish or shoe polish on leather. 0 Soiled leather should be cleaned immediately. If dirt is allowed to work into the finish, it can harm the leather.

6-53

Cleaning the Top of the Instrument Panel Use only mild soap and water to clean the top surfaces of the instrument panel. Sprays containing silicones or waxes may cause annoying reflections in the windshield and even make it difficult to see through the windshield under certain conditions. Care of Safety Belts Keep belts clean and dry.

Glass Glass should be cleaned often. GM Glass Cleaner (GM Part No. 1050427) or a liquid household glass cleaner will remove normal tobacco smoke and dust films. Don’t use abrasive cleaners on glass, because they may cause scratches. Avoid placing decals on the inside rear window, since they may have to be scraped off later. If abrasive cleaners are used on the inside of the rear window, an electric defogger element may be damaged. Any temporary license should not be attached across the defogger grid.

Do not bleach or dye safety belts. If you do, it may severely weaken them. In a crash, they might not be able to provide adequate protection. Clean-safety belts only with mild soap and lukewarm water.

6-54

Cleaning the Outside of the Windshield and Wiper Blades If the windshield is not clear after using the windshield washer, or if the wiper blade chatters when running, wax or other material may be on the blade or windshield. Clean the outside of the windshield with GM Windshield Cleaner, Bon-Ami Powder@ (GM Part No. 105001 1). The windshield is clean if beads do not form when you rinse it with water. Clean the blade by wiping vigorously with a cloth soaked in full-strength windshield washer solvent. Then rinse the blade with water. Wiper blades should be checked on a regular basis and replaced when worn. Weatherstrips Silicone grease on weatherstrips will make them last longer, seal better, and not stick or squeak. Apply silicone grease with a clean cloth at least every six months. During very cold, damp weather more frequent application may be required. (See “Recommended Fluids and Lubricants’’ in the Index.)

C1 ming the Outside of Your Vehicle The paint finish on your vehicle provides beauty, depth of color, gloss retention and durability. Washing Your Vehicle The best way to preserve your vehicle’s finish is to keep it clean by washing it often with lukewarm or cold water. Don’t wash your vehicle in the direct rays of the sun. Don’t use strong soaps or chemical detergents. Use liquid hand, dish or car washing (mild detergent) soaps. Don’t use cleaning agents that are petroleum based, or that contain acid or abrasives. All cleaning agents should be flushed promptly and not allowed to dry on the surface, or they could stain. Dry the finish with a soft, clean chamois or a 100% cotton towel to avoid surface scratches and water spotting. High pressure vehicle washes may cause water to enter your vehicle.

6-55

Finish Care Occasional waxing or mild polishing of your vehicle by hand may be necessary to remove residue from the paint finish. You can get GM-approved cleaning products from your dealer. (See “Appearance Care and Materials” in the Index.) Your GM manufactured vehicle may have a “basecoat/clearcoat” paint finish. The clearcoat gives more depth and gloss to the colored basecoat. Always use waxes and polishes that are non-abrasive and made for a basecoatklearcoat paint finish.

I NOTICE:

Machine compounding or aggressive polishing on a basecoatklearcoat paint finish may dull the finish or leave swirl marks.

Foreign materials such as calcium chloride and other salts, ice melting agents, road oil and tar, tree sap, bird droppings, chemicals from industrial chimneys, etc., can damage your vehicle’s finish if they remain on painted surfaces. Wash the vehicle as soon as possible. If necessary, use non-abrasive cleaners that are marked safe for painted surfaces to remove foreign matter. Exterior painted surfaces are subject to aging, weather and chemical fallout that can take their toll over a period of years. You can help to keep the paint finish looking new by keeping your vehicle garaged or covered whenever possible. Protecting Exterior Bright Metal Parts Bright metal parts should be cleaned regularly to keep their luster. Washing with water is all that is usually needed. However, you may use GM Chrome Polish on chrome or stainless steel trim, if necessary. Use special care with aluminum trim. To avoid damaging protective trim, never use auto or chrome polish, steam or caustic soap to clean aluminum. A coating of wax, rubbed to high polish, is recommended for all bright metal parts.

6-56

Sheet Metal Damage If your vehicle is damaged and requires sheet metal repair or replacement, make sure the body repair shop applies anti-corrosion material to the parts repaired or replaced to restore corrosion protection. Finish Damage Any stone chips, fractures or deep scratches in the finish should be repaired right away. Bare metal will corrode quickly and may develop into a major repair expense. Minor chips and scratches can be repaired with touch-up materials available from your dealer or other service outlets. Larger areas of finish damage can be corrected in your dealer’s body and paint shop.

Aluminum Wheels (If So Equipped) beep your wheels clean using a soft clean cloth with mild soap and water. Rinse with clean water. After rinsing thoroughly, dry with a soft clean towel. A wax may then be applied. The surface of these wheels is similar to the painted surface of your vehicle. Don’t use strong soaps, chemicals, abrasive polishes, abrasive cleaners or abrasive cleaning brushes on them because you could damage the surfxe. Don‘t take your vehicle through an automatic vehicle wash that has silicon carbide tire cleaning brushes. These brushes can also damage the surfxe of these wheels. Tires To clean your tires, use a stiff brush with a tire cleaner.

I NOTICE:

When applying a tire dressing always take care to wipe off any overspray or splash from all painted surfaces on the body or wheels of the vehicle. Petroleum-based products may damage the paint finish.

6-57

Underbody Maintenance Chemicals used for ice and snow removal and dust control can collect on the underbody. If these are not removed, accelerated corrosion (rust) can occur on the underbody parts such as fuel lines, frame, floor pan and exhaust system even though they have corrosion protection. At least every spring, flush these materials from the underbody with plain water. Clean any areas where mud and other debris can collect. Dirt packed in closed areas of t.he frame should be loosened before being flushed. Your dealer or an underbody vehicle washing system can do this for you.

Chemical Paint Spotting Some weather and atmospheric conditions can create a chemical fallout. Airborne pollutants can fall upon and attack painted surfaces on your vehicle. This damage can take two forms: blotchy, ringlet-shaped discolorations, and small irregular dark spots etched into the paint surface. Although no defect in the paint job causes this, GM will repair, at no charge to the owner, the surfaces of new vehicles damaged by this fallout condition within 12 months or 12,000 miles (20 000 k m ) of purchase, whichever occurs first. This applies only to materials manufactured and sold by General Motors. Bodies, body conversions or equipment not made or sold by General Motors are not covered.

Appearance Care Materials Chart I PARTNUMBER I

SIZE

DESCRIPTION

USAGE

I050004 IO501 72 1050 173 1050 I 74 I05020 I 10502 14 1 OS0427 1050429

1051515 I052870 105291 8** 1052929 I052930

2.75 sq. ft.

16 oz. (0.473 Lj 16 oz. (0.473 L) 16 oz. (0.473 L) 16 oz,. (0.473 L) 32 02. (0.946 Lj 23 oz. (0.680 L) 6 Ibs. (2.72 kg)

Chamois

Tar and Road Oil Remover Chrome Cleaner and Polish White Sidewall Tire Cleaner Magic Mirror Cleaner Polish Vinyl and Leather Cleaner

Glass Cleaner

Multi-Purpose Powdered Cleaner

I 32 oz. (0.946 L) I6 oz. (0.473 L) 8 oz. (0.237 L) 16 oz. (0.473 L) 8 0%. (0.237 L) 16 oz. (0.473 L)

Spot Lifter Optikleen

Wash and Wax Armor All

Concentrate Protector

Wheel Cleaner

Capture Dry Spot Remover

1~

Shines vehicle without scratching

Also removes old waxes and polishes

Removes rust and corrosion Removes soil and black marks

Exterior cleaner and polish

Spot and stain removal

Cleans grease, grime and smoke film Cleans vinyl, cloth, tires and mats

For cloth

Windshield washer solvent and antifreeze

-~

~~

~~

Exterior wash

Spray on wheel cleaner Attracts and absorbs soils

12345002**’ 12345725

I See your General Motors Parts Department for these products.

I 12 oz. (0.354 L) I

See “Fluids and Lubricants’’ in the Index.

Armor All Cleaner Silicone Tire Shine

Cleans vinyl, leather and rubber

**Not recommended for use on instrument panel vinyl. I

* Not recomrr.,..ded for pigskin suede leather.

. Shines tires - .,

- - . _

- -~

..

< -

6-59

Service Parts Identification Label You’ll find this label on the front passenger door frame. It’s very helpful if you ever need to order parts. On this label is:

your VIN, the model designation, 0 paint information, and 0 a list of all production options and special

equipment.

Be sure that this label is not removed from the vehicle.

Vehicle Identification Number (VIN)

SAMPLE4UXTM072675

E N G I N E A 6 f

CODE

MODEL YEAR

ASSEMBLY PLANT

This is the legal identifier for your vehicle. It appears on a plate in the front corner of the instrument panel, on the driver’s side. You can see it if you look through the windshield from outside your vehicle. The VIN also appears on the Vehicle Certification and Service Pats labels and the certificates of title and registration.

lgine Identification

The eighth character in your VIN is the engine code. This code will help you identify your engine, specifications and replacement parts.

6-60

Electrical System Add-on Electrical Equipment

NOTICE:

Don’t add anything electrical to your vehicle unless you check with your dealer first. Some electrical equipment can damage your vehicle and the damage wouldn’t be covered by your warranty. Some add-on electrical equipment can keep other components from working as they should.

Your vehicle has an air bag system. Before attempting to add anything electrical to your vehicle, see “Servicing Your Air Bag-Equipped Vehicle’’ in the Index.

Headlamp Wiring The headlamp wiring is protected by a circuit breaker in the lamp switch. An electrical overload will cause the lamps to flicker on and off, or in some cases to remain off. If this happens, have your headlamp wiring checked right away. Windshield Wiper Fuses The windshield wiper motor is protected by a circuit breaker and a fuse. If the motor overheats due to heavy snow, etc., the wiper will stop until the motor cools. Although the circuit is protected from electrical overload, overload due to heavy snow, etc., may cause wiper linkage damage. Always clear ice and heavy snow from the the windshield before using the windshield wipers. If the overload is caused by some electrical problem and not snow, etc., be sure to get it fixed. Power Windows and Other Power Options Circuit breakers in the fuse panel protect the power windows and other power accessories. When the current load is too heavy, the circuit breaker opens and closes. This protects the circuit until the current load returns to normal or the problem is fixed.

6-6 1

Instrument Panel

The fuse block access door is on the driver’s side of the instrument panel below the hood release lever.

feature of your vehicle that you can get along without -- like the radio or cigarette lighter -- and use its fuse, if it is of the value you need. Replace it as soon as you can. See “Fuses and Circuit Breakers’’ in the Index for more information.

FUSE BLOCK INFORMATION

You can remove fuses with a fuse extractor. The fuse extractor is mounted to the fuse block access door. To remove fuses if you don’t have a fuse extractor, hold the end of the fuse between your thumb and index finger and pull straight out. Be sure to use the correct fuse. If you ever have a problem on the road and don’t have a spare fuse, you can “borrow” one of the correct value. Just pick some

6-62

POSITION

1. 2. 3. 4.

5. 6. 7. 8. 9.

10. 11. 12.

13. 14.

15.

NAME STOP HTD MIR CTSY GAUGES

Hazard CRUISE PWR AUX Crank PARK LPS

AIR BAGS WIPER HTR-A/C CIG LTR ILLUM

DRL

CIRCUITS PROTECTED Stop/CHMSL, Stoplamps Electric Heated Mirrors Courtesy Lamps, Dome/RDG Lamps, Vanity Mirrors, Power Mirrors IP Cluster, DRL Relay, DRL Module, HDLP Switch, Keyless Entry Illumination, Low Coolant Module, CHIME Module, DRAB Module Hazard LampdCHIME Module Cruise Control Auxiliary Power Outlet, ALDL

License Plate Lamp, Parking Lamps, Taillamps, Front Sidemarkers, Glove Box Ashtray SDM Wiper Motor, Washer Pump A/C, A/C Blower, High Blower Relay, HTD Mirror Power Amp, Cigarette Lighter, Door Lock Relay LP Cluster, HVAC Controls, RR HVAC Controls, IP Switches, Radio Illumination, Door Switch Illumination DRL Relay

6-63

POSITION

16. 17. 18. 19. 20. 21. 22. 23. 24. A.?

B.?

NAME TURN B/U

RADIO- 1 BRAKE RADIO-B TRANS RR FOG Not Used Not Used RR HVAC PWR ACCY

PWR WDO

CIRCUITS PROTECTED Front Turn, RR Turn, Back-up Lamps, BTSI Solenoid Radio (Ign, Accy) 4WAL PCM, ABS, Cruise Control Radio (Battery), Power Antenna PRNDL, Automatic Transmission Rear Window Defog

RR HVAC Controls, HIGH, MED, LOW Relays Power Door Lock, Six-Way Power Seat, Keyless Entry Illumination Module Power Windows

?Circuit Breaker Do not use fuses of higher amperage than those recommended above. Fuse amperage levels are also imprinted on the fuse panel under the dash.

6-64

Capacities and Specifications Normal Maintenance Replacement Parts Replacement part numbers listed in this section are based on the latest information available at the time of printing, and are subject to change. If a part listed in this manual is not the same as the part used in your vehicle when it was built, or if you have any questions, please contact your GM truck dealer. These specifications are for information only. If you have any questions, see the service manual for the chassis or refer to the body manufacturer’s publications. Engine Identification -- Gasoline Engines Engine Type VIN Code Fuel System ‘Sequential Central Port Fuel Injection

? -Sequential Multi-Port Fuel Injection

“VORTEC” 4300

“VORTEC” 7400

“VORTEC” 5700

”VORTEC” 5000

V8 SF1 I

V6 SFI 1

V8 SFI 1

V8

SFI’

Wheel Nut Torque MODEL All

TORQUE 122 ft-lb (165 Nem)

Cooling System Capacity ENGINE “VORTEC” 4300 “VORTEC” SO00 “VORTEC” 5700 “VORTEC” 7400

VIN

QTY Without Rear Heater*

QTY With Rear Heater*

1 1 quarts ( 10.4 L) 17 quarts ( 16 L) 17 quarts (16 L) 23 quarts (2 1.8 L)

14 quarts (13.2 L) 20 quarts (18.9 L) 20 quarts (1 8.9 L) 26 quarts (24.6 L)

After refill, the level MUST be checked as outlined under “Engine Cooling System” in Section 5. *All quantities are approximate.

Crankcase Capacity ENGINE “VORTEC” 4300 “VORTEC” 5000 “VORTEC” 5700 “VORTEC” 7400

VIN

Quantity With Filter

4.5 quarts (4.3 L) 5 quarts (4.8 L) 5 quarts (4.8 L) 7 quarts (6.5 L)

All quantities are approximate. After refill, the level MUST be checked as outlined under “Engine Oil And Filter Recommendations” in Section 5. *Add an aS;lditis.ad quart (1 L) for RPO 5ZI and RPO KL5 Models.

6-66

Fuel Tank Capacity TYPE Standard Tank Cutaway Standard Tdnk Cutaway Optional Tank

All quantities are approximate.

QUANTITY

3 I gallons ( I 17.3 L) 35 gallons (132 L) 55 gallons (208.2 L)

:ermt Parts

Normal Rc --' Engine VIN Oil Filter Air Cleaner Filter'l' PCV Spark Plugs Fuel Filter Radiator Cap

Valve

"VORTEC" 4300

VORTEC" 5000

"VORTEC" 5700

"VORTEC" 7400

PFS2 A9 17C CV789C 4 1-932 GF48 1 RC36

PF1218 A9 17C c v 7 7 4 c 4 1-932 CF48 1 RC36

PF1218 A9 17C c v 7 7 4 c 4 1-932 GF48 1 RC36

PF1218 A917C c v 7 7 4 c 4 1-932 GF48 I RC36

'"For

severe dusty conditions, use AC Air Filter, Part No. 1236C.

6-67

Air Conditioning Refrigerants Not all air conditioning refrigerants are the same. If the air conditioning system in your vehicle needs refrigerant, be sure the proper refrigerant is used. If you’re not sure, ask your GM dealer.

TYPE

QTY Front

QTY Front and

Refrigerant R- 134a

Only 3.00 Ibs. (1.36 kg)

Rear

4.875 lbs. (2.21 kg)

6-68

Lamp and Bulb Data

LAMP OR BULB HEADLAMPS 2 Headlamp System (Sealed Beam System) Low/High Beam 4 Headlamp System (Composite Headlamp System) Low/High Beam High Beam

LAMP OR BULB EXTERIOR Front Sidemarker Lamp Front Park and Turn Lamp Rear Parking Lamp Rear Stop and Turn Lamp Back-up Lamp Back-up Lamp Rear Park, Stop and Turn Lamp CHMSL License Plate Lamp Underhood Lamp Reel Lamp

POWER RATING TRADE NO. AT 12.8V, WATTS

H6054

6052 9005

TRADE NO.

35/65

51 BO

194

2357NA

3057 3057 3156 1 IS6 1157 92 1 194 232 232

6-69

LAMP OR BULB INTERIOR Dome Lamps Reading Lamps IP Courtesy Lamp Stepwell Lamp Instrument Panel Compartment Lamp Ashtray Lamp Sunshade Vanity Mirror

LAMP OR BULB INSTRUMENT PANEL Daytime Running Lamps Indicator Charging System Indicator Lamp Instrument Cluster Illumination Headlamp Beam Indicator Turn Signal Indicator Brake Warning Indicator SIR (Air Bag) Safety Belt Warning Check Gages Indicator Malfunction Indicator ("Service Engine Soon") Lamp

6-70

TRADE NO.

21 1-2 21 1-2 194 194 194 194 74

TRADE NO.

74 74 194 74 74 74 74 74 74 74

214

NOTES

NOTES

6-72

Section 7 Maintenance Schedule

IMPORTANT. KEEP ENGINE OIL AT THE PROPER

LEVEL AND CHANGE AS

RECOMMENDED

This section covers the maintenance required for your vehicle. Your vehicle needs these services to retain its safety, dependability and emission control performance.

Have you purchased the GM Protection Plan? The Plan supple~nents your new vehicle warranties. See your Warranty and Owner Assistance hooklet, or your GM deuler for detuils.

Introduction Your Vehicle and the Environment Proper vehicle maintenance not only helps to keep your vehicle in good working condition, but also helps the environment. All recommended maintenance procedures are important. Improper vehicle maintenance can even affect the quality of the air we breathe. Improper fluid levels or the wrong tire inflation can increase the level of emissions from your vehicle. To help protect our environment, and to keep your vehicle in good condition, please maintain your vehicle properly.

7-1

How This Section is Organized The remainder of this section is divided into five parts: “Part A: Scheduled Maintenance Services” shows what to have done and how often. Some of these services can be complex, so unless you are technically qualified and have the necessary equipment, you should let your dealer’s service department or another qualified service center do these jobs.

Performing maintenance work on a vehicle can be dangerous. In trying to do some jobs, you can be seriously injured. Do your own maintenance work only if you have the required know-how and the proper tools and equipment for the job. If you have any doubt, have a qualified technician do the work.

If you are. skilled enough to do some work on your vehicle, you will probably want to get the service information GM publishes. See “Service and Owner Publications” in the Index.

7-2

“Part B: Owner Checks and Services” tells you what should be checked whenever you stop for fuel. It also explains what you can easily do to help keep your vehicle in good condition. “Part C: Periodic Maintenance Inspections” explains important inspections that your GM dealer’s service department or another qualified service center should perform. “Part D: Recommended $hias and Lubricants’’ lists some products GM recommends to help keep your vehicle properly maintained. These products, or their equivalents, should be used whether you do the work yourself or have it done. “Part E: Maintenance Record” provides a place for you to record the maintenance performed on your vehicle. Whenever any maintenance is performed, be sure to write it down in this part. This will help you determine when your next maintenance should be done. In addition, it is a good idea to keep your maintenance receipts. They may be needed to qualify your vehicle. for warranty repairs.

Part A: Scheduled Maintenance Services Using Your Maintenance Schedule We at General Motors want to help you keep your vehicle in good working condition. But we don‘t know exactly how you‘ll drive it. You may drive very short distances only a few times a week. Or you may drive long distances a l l the time in very hot, dusty weather. You may use your vehicle i n making deliveries. Or you may drive it to work, to do errands or in many other ways. Because of all the different ways people use their GM vehicles, maintenance needs vary. You may even need more frequent checks and replacements than you’ll find i n the schedules in this section. So please read this section and note how you drive. If you have any questions on how to keep your vehicle i n good condition, see your GM dealer. This part tells you the maintenance services you should have done and when you should schedule them. If you go to your dealer for your service needs, you’ll know that GM-trained and supported service people will perform the work using genuine GM parts.

The proper fluids and lubricants to use are listed in Part D. Make sure whoever services your vehicle uses these. All parts should be replaced and all necessary repairs done before you or anyone else drives the vehicle. These schedules are for vehicles that:

carry passengers and cargo within reconmended limits. You will find these limits on your vehicle’s Certification/Tire label. See “Loading Your Vehicle” i n the Index. are driven on reasonable road surfaces within legal driving limits. use the reconmended fuel. See “Fuel“ i n the Index.

Selecting the Right Schedule First you‘ll need to decide which of the two schedules is right for your vehicle. Here‘s how to decide which schedule to follow: Gasoline engine vehicles and diesel engine vehicles have different maintenance requirements. IC you have a diesel engine. follow a schedule designated for diesel engine vehicles only. See the Diesel Engine Supplement for diesel engine maintenance schedules.

7-3

Maintenance Schedule Short TripKity Definition -- Gasoline Engines Follow the Short Trip/City Maintenance Schedule if any one of these conditions is true for your vehicle:

Most trips are less than 5 to 10 miles (8 to 16 km). This is particularly important when outside temperatures are below freezing. Most trips include extensive idling (such as frequent driving in stop-and-go traffic j. Most trips are through dusty areas. You frequently tow a trailer or use a carrier on top of your vehicle. You frequently tow a trailer or us-e a carrier on top of your vehicle. (With some models, you should never tow a trailer. See “Towing a Trailer” in the Index.) If the vehicle is used for delivery service, police, taxi or other commercial application.

7-4

Short Trip/City Intervals -- Gasoline Engines Every 3,000 Miles (5 000 km): Engine Oil and Filter

Change (or 3 months, whichever occurs first). Chassis Lubrication (or 3 months, whichever occurs first). Drive Axle Service (or 3 months, whichever occurs first). At 6,000 Miles (10 000 km) -- Then Every 12,000 Miles (20 000 km): Tire Rotation.

Every 15,000 Miles (25 000 km): Air Cleaner Filter

Inspection, if driving in dusty conditions. Shields and Underhood Insulation Inspection (GVWR above 8,500 Ibs. only). Thermostatically Controlled Engine Cooling Fan Check (or every 12 months, whichever occurs first). Front Wheel Bearing Repack (or at each brake relining, whichever occurs first).

Every 30,000 Miles (50 000 km): Air Cleaner Filter

Replacement. Fuel Filter Replacement.

Every 50,000 Miles (83 000 km): Automatic

Transmission Service (vehicles over 8600 GVWR or driven under severe conditions only).

Maintenance Schedule I Short Trip/City Intervals -- Gasoline Engines

I Long Tkip/Highway Definition -- Gasoline Engines I

Every 60,000 Miles (100 000 km): Engine Accessory

Drive Belt Inspection. Fuel Tank, Cap and Lines Inspection. Exhaust Gas Recirculation System Inspection. Evaporative Control System Inspection. Every 100,000 Miles (166 000 km): Cooling System Service (or every 60 months, whichever occurs first). Spark Plug Wire Inspection. Spark Plug Replacement. Positive Crankcase Ventilation (PCV) Valve Inspection.

These intervals onlj? sumnariZe mlinterzcrnce services. Be sure to.follow the complete nzainterzance schedule on the jollowing pcrges.

Follow this maintenance schedule ordy if none of the conditions from the Short Trip/City Maintenance Schedule is true. Driviizg a vehicle with a f d l y warmed engine mder highway conditions c:a~~ses engine oil to break down slowe~:

7-5

Maintenance Schedule

Every 7,500 Miles (12 500 km): Engine Oil and Filter Change (or every 12 months, whichever occurs first). Chassis Lubrication (or every 12 months, whichever occurs first). Drive Axle Service.

At 7,500 Miles (12 500 km) -- Then Every 15,000 Miles (25 000 km): Tire Rotation.

Every 15,000 Miles (25 000 km): Shields and

Underhood Insulation Inspection (GVWR above 8,500 lbs. only). Thermostatically Controlled Engine Cooling Fan Check (or every 12 months, whichever occurs first).

Every 30,000 Miles (50 000 km): Fuel Filter

Replacement. Air Cleaner Filter Replacement. Front Wheel Bearing Repack (or at each brake relining, whichever occurs first).

Every 50,000 Miles (83 000 km): Automatic

Transmission Service (vehicles over 8600 GVWR or driven under severe conditions only).

7-6

Every 60,000 Miles (100 000 km): Engine Accessory

Drive Belt Inspection. Fuel Tank, Cap and Lines Inspection. Exhaust Gas Recirculation System Inspection. Evaporative Control System Inspection. Every 100,000 Miles (166 000 km): Cooling System Service (or every 60 months, whichever occurs fist). Spark Plug Wire Inspection. Spark Plug Replacement. Positive Crankcase Ventilation (PCV) Valve Inspection.

These intervals only sumnarize maintenance services. Be sure to follow the complete maintenance schedule on the.following pnges.

I Short Trip/City Maintenance Schedule -= Gasoline Engines I

The services shown in this schedule up to 100,000 miles ( 166 000 km) should be performed after 100,000 miles (166 000 km) at the same intervals. Footnotes f The U.S. Environmental Protection Agency or the California Air Resources Board has determined that the failure to perform this maintenance item will not nullify the emission warranty or limit recall liability prior to the completion of the vehicle’s useful life. We, however, urge that all recommended maintenance services be performed at the indicated intervals and the maintenance be recorded. # Lubricate the front suspenslon, kingpin bushings, steering linkage and rear driveline center splines.

*:!: Drive axle service:

Locking Differential -- Drain fluid and refill at first engine oil change. At subsequent oil changes, check fluid level and add fluid as needed. If driving in dusty areas or towing a trailer, drain fluid and refill every 15,000 miles (25 000 km). Standard Differential -- Check fluid level and add fluid as needed at every oil change. If driving in dusty areas or towing a trailer, drain fluid and refill every 15,000 miles (25 000 km). More frequent lubrication may be required for heavy-duty use.

7-7

I Short TripKity Maintenance Schedule -- Gasoline Engines I 3,000 Miles (5 000 km) 0 Change engine oil and filter (or every

6,000 Miles (10 000 km) 0 Change engine oil and filter (or every

3 months, whichever occurs first). An Emission Control Servic-e.

0 Lubricate chassis components; see footnote ## (or every 3 months, whichever occurs first). 0 Check axle fluid level and add fluid as needed. ** 0 Rotate tires. See “Tire Inspection and Rotation” in the Index for proper rotation pattern and additional information. During tire rotation, check brake calipers for freedom of movement. Refer to the appropriate GM service manual for proper caliper service procedures.

3 months, whichever occurs first). An Emission Control Service. 0 Lubricate chassis components; see

footnote ## (or every 3 months, whichever occurs first). as needed. **

CI Check axle fluid level and add fluid

DATE

ACTUAL MILEAGE SERVICED B Y

7-8

I Short TripKity Maintenance Schedule -- Gasoline Engines I 9,000 Miles (15 000 ks:) CI Change engine oil and filter (or every

12,000 Miles (20 000 km)

3 months, whichever occurs first). AH Emission Control Service. 0 Lubricate chassis components; see

footnote # (or every 3 months, whichever occurs first).

0 Check axle fluid level and add fluid

as needed. :$*

Change engine oil and filter (or every 3 months, whichever occurs first). An Emission Control Service.

I7 Lubricate chassis components; see

footnote # (or every 3 months, whichever occurs first).

0 Check axle fluid level and add fluid

as needed :%:I:

DATE

ACTUAL MILEAGE

SERVICED BY: I

DATE

ACTUAL MILEAGE

SERVICED B Y

7-9

Short TripKity Maintenance Schedule -- Gasoline Engines 15,000 Miles (25 000 km) 0 Change engine oil and filter (or every

3 months, whichever occurs first). Arz Emission Cotltr-ol Senlice. 0 Lubricate chassis components; see

footnote ## (or every 3 months, whichever occurs first).

El Inspect air cleaner filter if you are driving

in dusty conditions. Replace filter if necessary. AFI Emission C o n t d Stjt-vic’o. 0 Check axle tluid level and add fluid as needed. ** Clean and repack the front wheel bearings (or at each brake relining, whichever occurs first).

0 Vehicles With GVWR Above 8,500 lbs.

Only: Inspect shields and underhood insulation for damage or looseness. Adjust or replace as required. This is Noise Emission Control Ser\*icc_. Applicnble only to vehicles sold irz the United Stl1te.s.

0 If your engine has a thermostatically

controlled cooling fan, inspect all hoses and ducts for proper hook-up (or every 12 months, whichever occurs first). Be sure the valve works properly. 7his is CI Noise Emission Corltrol Service. Applicddr o n l ~ to \~cl~ic.lcs s o l d in the United Stcrtes.

DArE

ACTUAL MILEAGE

SERVICED B Y

7-10

I Short TripKity Maintenance Schedu :e -- Gasoline Engines I 18,000 Miles (30 000 km) 0 Change engine oil and filter (or every

21,000 Miles (35 000 km) cl Change engine oil and filter (or every

3 months, whichever occurs first). A11 Emissiou Control Sut-vic*u.

0 Lubricate chassis components; see footnote # (or every 3 months, whichever occurs first). 17 Check axle fluid level and add fluid as needed :K>K 0 Rotate tires. See “Tire Inspection and

Rotation” in the Index for proper rotation pattern and additional information. During tire rotation, check brake calipers for freedom of movement. Refer to the appropriate GM service manual for proper caliper service procedures. I ACTUAL MILEAGE

ISERVICED

I DATE

BY:

3 months, whichever occurs first). At7 Emi.s.sio/l Co\71\-i)l S c ~ r ~ ~ i c - c . 0 Lubricate chassis components; see

footnote # (or every 3 months, whichever occurs first).

0 Check axle fluid level and add fluid

as needed :k:3

DATE

ACTUAL MII,EAGE

SERVICED BY:

7-11

I Short TripKity Maintenance Schedule -- Gasoline Engines 1 24,000 Miles (40 000 km) 0 Change engine oil and filter (or every

27,000 Miles (45 000 km) 0 Change engine oil and filter (or every

3 months, whichever occurs first). An Emission Control Service. 0 Lubricate chassis components; see

footnote # (or every 3 months, whichever occurs first). as needed. **

0 Check axle fluid level and add flu id

3 months, whichever occurs first). An Emission Control Service. Lubricate chassis components; see footnote # (or every 3 months, whichever occurs first). as needed. **

I7 Check axle fluid level and add fluid

I DATE

I ACTUAL MILEAGE

ISERVICED

B Y I

DATE

ACTUAL MILEAGE

SERVICED BY:

7-12

I Short TripKity Maintenance Schedule -- Gasoline Engines 1 30,000 Miles (50 000 km) 0 Change engine oil and filter (or every

0 If your engine has a thermostatically

controlled cooling fan, inspect all hoses and ducts for proper hook-up (or every 12 months, whichever occurs first). Be sure the valve works properly. This is u Noise to Etnissiou Coutrol Service. Applicable o ~ d ~ whic.les sold in the United States. 0 Rotate tires. See “Tire Inspection and

Rotation” in the Index for proper rotation pattern and additional information. During tire rotation, check brake calipers for freedom of movement. Refer to the appropriate GM service manual for proper caliper service procedures.

3 months, whichever occurs first). An Emissiol~ Control Service.

0 Lubricate chassis components; see footnote # (or every 3 months, whichever occurs first). 0 Check axle fluid level and add fluid as needed. ** 0 Clean and repack the front wheel bearings (or at 0 Replace fuel filter.

each brake relining, whichever occurs first). An Emission Control Service. 3- Replace air cleaner filter. An Etnissiorz Control Service.

0 Vehicles With GVWR Above 8,500 lbs. Only: Inspect shields and underhood insulation for damage or looseness. Adjust or replace as required. This is a Noise Emission Control Service. Applicable only to vehicles sold in the United Stutes.

7-13

I Short Trip/City Maintenance Schedule -- Gasoline Engines I 33.000 Milt 0 Change engine oil and filter (or every

36,000 Miles (60 000 km) 0 Change engine oil and filter (or every

(55 000 rn)

.-

3 months, whichever occurs first). An E~nission Con.trol Service. 0 Lubricate chassis components; see

footnote # (or every 3 months, whichever occurs first).

0 Check axle fluid level and add fluid

as needed. w

3 months, whichever occurs first). An Emission Control Service. 0 Lubricate chassis components; see

footnote # (or every 3 months, whichever occurs first). as needed. **

0 Check axle fluid level and add fluid

DATE

ACTUAL MILEAGE

SERVICED B Y

DATE

ACTUAL MILEAGE

SERVICED BY:

7-14

I Short TripKity Maintenance Schedule -- Gasoline Engines 1

0 Change engine oil and filter (or every

3 months, whichever occurs first). An Emission Control Service. 0 Lubricate chassis components; see

footnote # (or every 3 months, whichever occurs first). as needed. **

0 Check axle fluid level and add fluid

ACTUAL MILEAGE 1

I DATE

MILEAGE

ACTUAL

DATE

42,000 Miles (70 000 km) 0 Change engine oil and filter (or every

3 months, whichever occurs first). An Emission Control Service.

0 Lubricate chassis components; see footnote # (or every 3 months, whichever occurs first). 0 Check axle fluid level and add fluid as needed. ** 0 Rotate tires. See “Tire Inspection and Rotation” in the Index for proper rotation pattern and additional information. During tire rotation, check brake calipers for freedom of movement. Refer to the appropriate GM service manual for proper caliper service procedures.

7-15

SERVICED BY: I

Short Trip/City Maintenance Schedule -- Gasoline Engines 45,000 Miles (75 000 km)

Change engine oil and filter (or every 3 months, whichever occurs first). An Emission Control Service. 0 Lubricate chassis components; see

footnote ## (or every 3 months, whichever occurs first). as needed. **

17 Check axle fluid level and add fluid 0 Clean and repack the fron (or at each brake relining, occurs first). Cl Inspect air cleaner filter if

t wheel bearings whichever

’ you are driving

in dusty conditions. Replace filter if necessary. An Emission Control Service.

0 Vehicles With GVWR Above 8,500 Ibs.

Only: Inspect shields and underhood insulation for damage or looseness. Adjust or replace as required. This is u Noise Emission Cmr-d Service. Applicable only to vehicles sold irz the United States.

0 If your engine has a thermostatically

controlled cooling fan, inspect all hoses and ducts for proper hook-up (or every 12 months, whichever occurs first). Be sure the valve works properly. This is N Noise Emi-sion Control Service. Applicable only to vehicles .sold in the United StLttes.

1 DATE

I ACTUAL MILEAGE

ISERVICED BY: I

7-16

I Short TripKity Maintenance Schedule -- Gasoline Engines I 48,000 Miles (80 000 km) 0 Change engine oil and filter (or every

50,000 Miles (83 000 km) 0 Change automatic transmission fluid and

3 months, whichever occurs first). 0 Lubricate chassis components; see

footnote ## (or every 3 months, whichever occurs first).

17 Check axle fluid level and add fluid

as needed. ‘W

filter if the vehicle’s GVWR is over 8600 lbs. or if the vehicle is mainly driven under one or more of these conditions: - In heavy city traffic where the outside

temperature regularly reaches 90°F (32 O C) or higher.

- In hilly or mountainous terrain. - When doing frequent trailer towing. - Uses such as found in taxi, police or

delivery service.

DATE

ACTUAL MILEAGE

SERVICED B Y

7-17

I Short TriplCity Maintenance Schedule -- Gasoline Engines I 51,000 Miles (85 000 km) CI Change engine oil and filter (or every

54,000 Miles (90 000 km) 0 Change engine oil and filter (or every

3’ months, whichever occurs first). AII Emissim Control Ser.llic*c..

0 Lubricate chassis components; see footnote ## (or every 3 months, whichever occurs first). 0 Check axle fluid level and add fluid 0 Rotate tires. See “Tire Inspection and

as needed. *‘k

Rotation’’ in the Index for proper rotation pattern and additional information. During tire rotation, check brake calipers for freedom of movement. Refer to the appropriate GM service manual for proper caliper service procedures.

3 months, whichever occurs first). Ala Emissior~ Control Serllic-e. 0 Lubricate chassis components; see

footnote # (or every 3 months, whichever occurs first).

0 Check axle fluid level and add fluid

as needed :i:Q

DATE

ACTUAL MILEAGE

SERVICED B Y

7-18

I Short Trip/City Maintenance Schedule -- Gasoline Engines I 57,000 Miles (95 000 km) Cl Change engine oil and filter (or every

3 months, whichever occurs first). An Emission Control Service. 0 Lubricate chassis components; see

footnote ## (or every 3 months, whichever occurs first). as needed. **

0 Check axle fluid level and add fluid

60,000 Miles (100 000 km) 0 Change engine oil and filter (or e\ 3 months, whichever occurs first). An En.zission Control Service.

0 Lubricate chassis components; see footnote # (or every 3 months, whichever occurs first). 0 Check axle fluid level and add fluid as needed. ** 0 Clean and repack the front wheel bearings

(or at each brake relining, whichever occurs first).

I ACTUAL MILEAGE

Only: Inspect shields and underhood insulation for damage or looseness. Adjust or replace as required. This i.s a Noise E/7zis.sion Control Service. Appliccrble only to vehicles sold in the United States.

0 Vehicles With GVWR Above 8,500 lbs.

SERVICED BY.

(Continued) 7-19

Short TripKity Maintenance Schedule -- Gasoline Engines 60,000 Miles (100 000 km) (Continued) 0 If your engine has a thermostatically

controlled cooling fan, inspect all hoses and ducts for proper hook-up (or every 12 months, whichever occurs first). Be sure the valve works properly. This is LI Noise Emission Control Senice. Applicublp o n 1 ~ to vehicles sold in the United Stcrtes. 0 Inspect engine accessory drive belt. 0 Replace fuel filter. 0 Conduct Exhaust Gas Recirculation (EGR)

AI? Emissiorz Control Service.

An Emission Colafro1 Service.

system inspection as described in the service manual. A11 Emissiofz Comol Service.

0 Conduct evaporative control system

inspection. Check all fuel and vapor lines and hoses for proper hook-up, routing and condition. Check that the purge valve works properly (if equipped). Replace as needed. An Emisxion Cor1 fro1 SL>rvico. 0 Replace air cleaner filter. An Emissinll Cof7fm1 Service'. 17 Inspect fuel tank, cap and lines for damage

or leaks. Inspect fuel cap gasket for any damage. Replace parts as needed. AH Emissior7 Coutr-ol Ser?>ic.e. 7 L

I DATE

I ACTUAL MILEAGE

I SERVICED B Y I

I Short TripKity Maintenance Schedule -- Gasoline Engines 1 63,000 Miles (105 000 km) 0 Change engine oil and filter (or every

66,000 Miles (110 000 km)

3 months, whichever occurs first). An Emissiol? Control Service. 0 Lubricate chassis components; see

footnote # (or every 3 months, whichever occurs first). as needed :>*

0 Check axle fluid level and add fluid

I DATE

ACTUAL

MILEAGE

Change engine oil and filter (or every 3 months, whichever occurs first). AI] Emissiorl Control Srrl+c:c).

I7 Lubricate chassis components; see footnote # (or every 3 months, whichever occurs first). 0 Check axle fluid level and add fluid as needed *:3 0 Rotate tires. See “Tire Inspection and

Rotation” in the Index for proper rotation pattern and additional information. During tire rotation, check brake calipers for freedom of movement. Refer to the appropriate GM service manual for proper caliper service procedures.

SERVICED BY:

7-21

Short TripKity Maintenance Schedule -- Gasoline Engines 69,000 Miles (115 000 km) 0 Change engine oil and filter (or every

72,000 Miles (120 000 km) 0 Change engine oil and filter (or every

3 months, whichever occurs first). An Emission Co17trol Service. 0 Lubricate chassis components; see

footnote # (or every 3 months, whichever occurs first).

0 Check axle fluid level and add fluid

as needed. ‘k*

3 months, whichever occurs first). AII Ernissior~ Control Service. 0 Lubricate chassis components; see

footnote # (or every 3 months, whichever occurs first). as needed. * ‘g

0 Check axle fluid level and add fluid

I DATE

I ACTUAL MILEAGE

ISERVICED

BY I

DATE

ACTUAL MILEAGE

SERVICED B Y

7 33

75,000 Miles (125 008 km) 0 Change engine oil and filter (or every

3 months, whichever occurs first). An Emission Control Service. 0 Lubricate chassis components; see

footnote # (or every 3 months, whichever occurs first). 0 Clean and repack the front wheel bearings

(or at each brake relining, whichever occurs first).

0 Inspect air cleaner filter if you are driving

in dusty conditions. Replace filter if necessary. An Emission Control Service. 0 Check axle fluid level and add fluid as needed. **

0 Vehicles With GVWR Above 8,500 lbs.

Only: Inspect shields and underhood insulation for damage or looseness. Adjust or replace as required. This is LI Noise Emission Control Servico. Applicable only to vehicles s o l d in tlw UP1itc.d Stcrtes.

0 If your engine has a thermostatically

controlled cooling fan, inspect all hoses and ducts for proper hook-up (or every 12 months, whichever occurs first). Be sure the valve works properly. This is a Noise Emission Cor7tmI Service. Applicable ordy to vehicles sold in the United Stutes.

7-23

Short TripKity Maintenance Schedule -- Gasoline Engines > 78,000 Miles (130 000 km) 0 Change engine oil and filter (or every

81,000 Miles (135 000 km) 0 Change engine oil and filter (or every

3 months, whichever occurs first). An E I ~ I ~ S S ~ O I I

Control Service.

0 Lubricate chassis components; see footnote # (or every 3 months, whichever occurs first). 0 Check axle fluid level and add fluid 0 Rotate tires. See “Tire Inspection and

as needed. #’*

Rotation” in the Index for proper rotation pattern and additional information. During tire rotation, check brake calipers for freedom of movement. Refer to the appropriate GM service manual for proper caliper service procedures.

3 months, whichever occurs first). An Emission Control Service. Lubricate chassis components; see footnote ## (or every 3 months, whichever occurs first).

0 Check axle fluid level and add fluid

as needed. ‘k*

DATE

ACTUAL MILEAGE

SERVICED B Y

DATE

ACTUAL MILEAGE

SERVICED B Y

7-24

I Short TripKity Maintenance Schedule =- Gasoline Engines I 84,000 Miles (140 000 km) 0 Change engine oil and filter (or every

87,000 Miles (145 000 km) 0 Change engine oil and filter (or every

3 months, whichever occurs first). An Emission Control Service. 0 Lubricate chassis components; see

footnote # (or every 3 months, whichever occurs first).

0 Check axle fluid level and add fluid

as needed :i: :k

3 months, whichever occurs first). AI? Elnission Control Service. 0 Lubricate chassis components; see

footnote # (or every 3 months, whichever occurs first).

0 Check axle fluid level and add fluid

as needed. ‘M

DATE

ACTUAL MILEAGE

SERVICED B Y

7-25

Short TriplCity Maintenance Schedule -- Gasoline Engines 90,000 Miles (150 000 km) 0 Change engine oil and filter (or every

3 months, whichever occurs first). An Em,ission Control Service. 0 Lubricate chassis components; see

footnote ## (or every 3 months, whichever occurs first). as needed. **

0 Check axle fluid level and add fluid 0 Clean and repack the front wheel bearings

(or at each brake relining, whichever occurs first).

0 Replace fuel filter.

An Emission Control Service. -f

17 Replace air cleaner filter. An Emission Control Service. 0 Rotate tires. See “Tire Inspection and

Rotation” in the Index for proper rotation pattern and additional information. During tire rotation, check brake calipers for freedom of movement. Refer to the appropriate GM service manual for proper caliper service procedures.

0 Vehicles With GVWR Above 8,500 lbs.

Only: Inspect shields and underhood insulation for damage or looseness. Adjust or replace as required. This is a Noise Emission Control Service. Applicable only to vehicles sold in the United States.

I Short TripKity Maintenance Schedule =- Gasoline Engines I

0 If your engine has a thermostatically

controlled cooling fan, inspect all hoses and ducts for proper hook-up (or every 12 months, whichever occurs first). Be sure the valve works properly. This is CL Noise E I T ~ ~ S S ~ O I I Cotm-d Service. Applicdde or1lv to vehicles sold if1 the United StLrtes.

93,000 Miles (155 000 km) El Change engine oil and filter (or every

3 months, whichever occurs first). Arz Emis.siou Contra[ Srl-\.~ic~e. 0 Lubricate chassis components; see

foot.note # (or every 3 months, whichever occurs first).

0 Check axle fluid level and add fluid

as needed :K:k

DATE

ACTUAL

MILEAGE

SERVICED

B Y

DATE

ACTUAL MILEAGE

SERVICED B Y

7-27

1 Short Trip/City Maintenance Schedule -- Gasoline Engines I 96,000 Miles (160 000 km) 0 Change engine oil and filter (or every

99,000 Miles (165 000 km) 0 Change engine oil and filter (or every

3 months, whichever occurs first). AH Emission Cmtrol Service. 0 Lubricate chassis components; see

footnote # (or every 3 months, whichever occurs first).

0 Check axle fluid level and add fluid

as needed. ‘H

3 months, whichever occurs first). An em is sin^^ Control Service. 0 Lubricate chassis components; see

footnote # (or every 3 months, whichever occurs first).

0 Check axle fluid level and add fluid

as needed. :%:>

. < ACTUAL MILEAGE SERVICED

B Y

I DATE

I ACTUAL MILEAGE

ISERVICED

BY:(

7-28

1 Short Trip/City Maintenance Schedule -- Gasoline Engines I 100,000 Miles (166 000 km) 0 Drain, flush and refill cooling system (or every 60 months since last service whichever occurs first). See “Engine Coolant” in the Index for what to use. Inspect hoses. Clean radiator, condenser, pressure cap and neck. Pressure test cooling system and pressure cap. AI1 Emission Control Service. 0 Inspect spark plug wires. An Ernission Control Service. 0 Replace spark plugs. 0 Change automatic transmission fluid and

An Emission Colztrol Service.

delivery service.

- In heavy city traffic where the outside

temperature regularly reaches 90” F (32°C) or higher.

- In hilly or mountainous terrain. - When doing frequent trailer towing. - Uses such as found in taxi, police or

I f y x t do m t use y x . t r vehicle lmder- any of thew conditio~~s, the flL.rici md,filt6>r do not require dhnging.