Download PDF Manual

LIFTGATE OPEN This message displays and a chime sounds if the liftgate is open while the ignition is in ON/RUN. Turn off the vehicle and check the liftgate. Restart the vehicle and check for the message on the DIC display. PASSENGER DOOR OPEN This message displays and a chime sounds if the passenger door is not fully closed and the vehicle is shifted out of P (Park). Stop and turn off the vehicle, check the door for obstructions, and close the door again. Check to see if the message still appears on the DIC. POWER LIFTGATE OFF This message displays when the power liftgate has been turned off by pressing the power liftgate button on the center stack.


RIGHT REAR DOOR OPEN This message displays and a chime sounds if the passenger side rear door is not fully closed and the vehicle is shifted out of P (Park). Stop and turn off the vehicle, check the door for obstructions, and close the door again. Check to see if the message still appears on the DIC.


Engine Cooling System Messages


ENGINE HOT A/C (Air Conditioning) OFF This message displays when the engine coolant becomes hotter than the normal operating temperature. See Engine Coolant Temperature Gauge on page 5-12. To avoid added strain on a hot engine, the air conditioning compressor automatically turns off. When the coolant temperature returns to normal, the air conditioning compressor turns back on. You can continue to drive your vehicle.


GMC Acadia/Acadia Denali Owner Manual (GMNA-Localizing-U.S./Canada/ Mexico-7576030) - 2015 - CRC - 8/18/14


Black plate (35,1)


Instruments and Controls


5-35


If this message continues to appear, have the system repaired by your dealer as soon as possible to avoid damage to the engine. ENGINE OVERHEATED IDLE ENGINE This message displays when the engine coolant temperature is too hot. Stop and allow the vehicle to idle until it cools down. See Engine Coolant Temperature Gauge on page 5-12. See Overheated Engine Protection Operating Mode on page 10-18 for information on driving to a safe place in an emergency. ENGINE OVERHEATED STOP ENGINE This message displays and a continuous chime sounds if the engine cooling system reaches unsafe temperatures for operation. Stop and turn off the vehicle as soon as it is safe to do so to avoid


severe damage. This message clears when the engine has cooled to a safe operating temperature.


Engine Oil Messages


CHANGE ENGINE OIL SOON This message displays when service is required for the vehicle. See your dealer. See Engine Oil on page 10-7 and Maintenance Schedule on page 11-2. Acknowledging the CHANGE ENGINE OIL SOON message will not reset the OIL LIFE REMAINING. See “Oil Life” under Driver Information Center (DIC) on page 5-23 and Engine Oil Life System on page 10-9. ENGINE OIL LOW — ADD OIL On some vehicles, this message displays when the engine oil level may be too low. Check the oil level before filling to the recommended level. If the oil is not low and this


message remains on, take the vehicle to your dealer for service. See Engine Oil on page 10-7. OIL PRESSURE LOW STOP ENGINE This message displays when the vehicle's engine oil pressure is low. The oil pressure light also appears on the instrument cluster. See Engine Oil Pressure Light on page 5-21. Stop the vehicle immediately, as engine damage can result from driving a vehicle with low oil pressure. Have the vehicle serviced by your dealer as soon as possible when this message is displayed.


Engine Power Messages


ENGINE POWER IS REDUCED This message displays and a chime sounds when the cooling system temperature gets too hot and the engine further enters the engine


GMC Acadia/Acadia Denali Owner Manual (GMNA-Localizing-U.S./Canada/ Mexico-7576030) - 2015 - CRC - 8/18/14


Black plate (36,1)


5-36


Instruments and Controls


coolant protection mode. See Engine Overheating on page 10-16
for further information. This message also displays when the vehicle's engine power is reduced. Reduced engine power can affect the vehicle's ability to accelerate. If this message is on, but there is no reduction in performance, proceed to your destination. The performance may be reduced the next time the vehicle is driven. The vehicle may be driven at a reduced speed while this message is on, but acceleration and speed may be reduced. Anytime this message stays on, the vehicle should be taken to your dealer for service as soon as possible.


Fuel System Messages


FUEL LEVEL LOW This message displays and a chime sounds if the fuel level is low. Refuel as soon as possible. See Fuel Gauge on page 5-11 and Fuel on page 9-42 for more information.


TIGHTEN GAS CAP This message may display along with the check engine light on the instrument cluster if the vehicle's fuel cap is not tightened properly. See Malfunction Indicator Lamp on page 5-15. Reinstall the fuel cap fully. See Filling the Tank on page 9-43. The diagnostic system can determine if the fuel cap has been left off or improperly installed. A loose or missing fuel cap allows fuel to evaporate into the atmosphere. A few driving trips with the cap properly installed should turn this light and message off.


Key and Lock Messages


REPLACE BATTERY IN REMOTE KEY This message displays if a Remote Keyless Entry (RKE) transmitter battery is low. The battery needs to be replaced in the transmitter. See “Battery Replacement” under Remote Keyless Entry (RKE) System Operation on page 2-2.


Lamp Messages


AUTOMATIC LIGHT CONTROL OFF This message displays when the automatic headlamps are turned off. This message clears itself after 10 seconds. AUTOMATIC LIGHT CONTROL ON This message displays when the automatic headlamps are turned on. This message clears itself after 10 seconds. TURN SIGNAL ON This message displays and a chime sounds if a turn signal is left on for 1.2 km (0.75 mi). Move the turn signal lever to the off position.


GMC Acadia/Acadia Denali Owner Manual (GMNA-Localizing-U.S./Canada/ Mexico-7576030) - 2015 - CRC - 8/18/14


Black plate (37,1)


Instruments and Controls


5-37


Object Detection System Messages


FORWARD COLLISION ALERT UNAVAILABLE This message displays when attempting to activate the Forward Collision Alert (FCA) system when it is temporarily unavailable. The FCA system does not need service. This message could be due to the camera being blocked. Cleaning the outside of the windshield behind the rearview mirror may correct the issue. FRT CAMERA BLOCKED CLEAN WINDSHIELD This message displays when the camera is blocked. Cleaning the outside of the windshield behind the rearview mirror may correct the issue. The Lane Departure Warning system will not operate. Forward Collision Alert (FCA) may not work or may not work as well.


LANE DEPARTURE SYS UNAVAILABLE This message displays when attempting to activate the Lane Departure Warning (LDW) system when it is temporarily unavailable. The LDW system does not need service. This message could be due to the camera being blocked. Cleaning the outside of the windshield behind the rearview mirror may correct the issue. PARK ASST BLOCKED SEE OWNERS MANUAL This message displays if there is something interfering with the Rear Parking Assist (RPA) system. See Parking Assist on page 9-35. PARK ASSIST OFF After the vehicle has been started, this message displays to remind the driver that the RPA system has


been turned off. To turn the RPA system back on, see Parking Assist on page 9-35. REAR CROSS TRAFFIC ALERT SYSTEM OFF If the vehicle has the Rear Cross Traffic Alert (RCTA) system, this message displays when the RCTA system has been turned off. See Rear Vision Camera (RVC) on page 9-38 and Driver Information Center (DIC) on page 5-23. SERVICE FRONT CAMERA If this message remains on after continued driving, the vehicle needs service. Do not use the Lane Departure Warning (LDW) and Forward Collision Alert (FCA) features. Take the vehicle to your dealer. SERVICE PARK ASSIST This message displays if there is a problem with the Rear Parking Assist (RPA) system. Do not use


GMC Acadia/Acadia Denali Owner Manual (GMNA-Localizing-U.S./Canada/ Mexico-7576030) - 2015 - CRC - 8/18/14


Black plate (38,1)


5-38


Instruments and Controls


SIDE DETECTION SYS TEMPORARILY OFF If your vehicle has the Side Blind Zone Alert (SBZA) system, this message displays when the SBZA system is disabled because the sensor cannot detect vehicles in your blind zone. The sensor may be blocked by mud, dirt, snow, ice, or slush. This message may also display during heavy rain or due to road spray. It may also come on when driving in isolated areas with no guardrails, trees, or road signs and light traffic. Your vehicle does not need service. For cleaning instructions, see “Washing the Vehicle” in Exterior Care on page 10-75. See Side Blind Zone Alert (SBZA) on page 9-36.


this system to help you park. See Parking Assist on page 9-35. See your dealer for service. SERVICE SIDE DETECTION SYSTEM If your vehicle has the Side Blind Zone Alert (SBZA) system and this message displays, both SBZA displays will remain on indicating there is a problem with the SBZA system. If these displays remain on after continued driving, the system needs service. See your dealer. See Side Blind Zone Alert (SBZA) on page 9-36. SIDE BLIND ZONE ALERT SYSTEM OFF If your vehicle has the Side Blind Zone Alert (SBZA) system, this message displays when the SBZA system has been turned off. See Side Blind Zone Alert (SBZA) on page 9-36 and Driver Information Center (DIC) on page 5-23.


Ride Control System Messages


SERVICE STABILITRAK This message displays if there is a problem with the StabiliTrak® system. If this message appears, try to reset the system. Stop; turn off the engine for at least 15 seconds; then start the engine again. If this message still comes on, it means there is a problem. See your dealer for service. The vehicle is safe to drive, however, you do not have the benefit of StabiliTrak, so reduce your speed and drive accordingly. SERVICE TRACTION CONTROL This message displays when there is a problem with the Traction Control System (TCS). When this message is displayed, the system will not limit wheel spin. Adjust your driving accordingly. See your dealer for service. See Traction Control/ Electronic Stability Control on page 9-28 for more information.


GMC Acadia/Acadia Denali Owner Manual (GMNA-Localizing-U.S./Canada/ Mexico-7576030) - 2015 - CRC - 8/18/14


Black plate (39,1)


Instruments and Controls


5-39


TRACTION CONTROL OFF This message displays when the Traction Control System (TCS) is turned off. Adjust your driving accordingly. See Traction Control/ Electronic Stability Control on page 9-28. TRACTION CONTROL ON This message displays when the Traction Control System (TCS) is turned on. See Traction Control/ Electronic Stability Control on page 9-28. This message clears itself after 10 seconds.


Airbag System Messages


SERVICE AIR BAG This message displays if there is a problem with the airbag system. Have your dealer inspect the system for problems. See Airbag Readiness Light on page 5-14 and Airbag System on page 3-22 for more information.


Security Messages


SERVICE THEFT DETERRENT SYSTEM This message displays when there is a problem with the theft-deterrent system. The vehicle may or may not restart so you may want to take the vehicle to your dealer before turning off the engine. See Immobilizer Operation on page 2-13 for more information. THEFT ATTEMPTED This message displays if the content theft-deterrent system has detected a break-in attempt while you were away from your vehicle. See Vehicle Alarm System on page 2-11 for more information.


Service Vehicle Messages


SERVICE A/C (Air Conditioning) SYSTEM This message displays when the electronic sensors that control the air conditioning and heating


systems are no longer working. Have the climate control system serviced by your dealer if you notice a drop in heating and air conditioning efficiency. SERVICE POWER STEERING This message displays when a problem is detected with the power steering system. When this message is displayed, you may notice that the effort required to steer the vehicle increases or feels heavier, but you will still be able to steer the vehicle. Have your vehicle serviced by your dealer immediately. SERVICE VEHICLE SOON This message displays when a non-emissions related malfunction occurs. Have the vehicle serviced by your dealer as soon as possible.


GMC Acadia/Acadia Denali Owner Manual (GMNA-Localizing-U.S./Canada/ Mexico-7576030) - 2015 - CRC - 8/18/14


Black plate (40,1)


5-40


Instruments and Controls


STARTING DISABLED SERVICE THROTTLE This message displays when your vehicle's throttle system is not functioning properly. Have your vehicle serviced by your dealer.


Tire Messages


TIRE LOW ADD AIR TO TIRE On vehicles with the Tire Pressure Monitor System (TPMS), this message displays when the pressure in one or more of the vehicle's tires is low. This message also displays LEFT FRT (left front), RIGHT FRT (right front), LEFT RR (left rear), or RIGHT RR (right rear) to indicate the location of the low tire. The low tire pressure warning light will also come on. See Tire Pressure Light on page 5-21.


If a tire pressure message appears on the DIC, stop as soon as you can. Inflate the tires by adding air until the tire pressure is equal to the values shown on the Tire and Loading Information label. See Tires on page 10-37, Vehicle Load Limits on page 9-9, and Tire Pressure on page 10-45. The DIC also shows the tire pressure values. See Driver Information Center (DIC) on page 5-23. SERVICE TIRE MONITOR SYSTEM On vehicles with the Tire Pressure Monitor System (TPMS), this message displays if a part on the TPMS is not working properly. The tire pressure light also flashes and then remains on during the same ignition cycle. See Tire Pressure Light on page 5-21. Several conditions may cause this message to appear. See Tire Pressure Monitor Operation on page 10-47 for more information. If the warning


comes on and stays on, there may be a problem with the TPMS. See your dealer. TIRE LEARNING ACTIVE This message displays when the Tire Pressure Monitor System (TPMS) is relearning the tire positions on your vehicle. The tire positions must be relearned after rotating the tires or after replacing a tire or sensor. See Tire Rotation on page 10-51, Tire Pressure Monitor System on page 10-46, and Tire Pressure on page 10-45 for more information.


Transmission Messages


ALL WHEEL DRIVE OFF If your vehicle has the All-Wheel Drive (AWD) system, this message displays when there is a temporary condition making the AWD system unavailable. The vehicle will run in 2WD. This could be caused by: . A compact spare tire on the


vehicle


GMC Acadia/Acadia Denali Owner Manual (GMNA-Localizing-U.S./Canada/ Mexico-7576030) - 2015 - CRC - 8/18/14


Black plate (41,1)


Instruments and Controls


5-41


. AWD system overheat


Loss of wheel or vehicle speed . Certain other vehicle electrical


conditions


This message turns off when the compact spare tire is replaced by a full-size tire, the differential fluid cools or the above conditions are no longer present and the warning message is reset. To reset the warning message manually, turn the ignition off and then back on again after 30 seconds. If the message stays on, see your dealer. See All-Wheel Drive on page 9-26. SERVICE ALL WHEEL DRIVE This message displays if a problem occurs with the All-Wheel Drive (AWD) system. The vehicle will run in 2WD. This could be caused by: . An electronics problem . Worn out or overheated clutch


plates


. Various electrical issues


If this message appears, stop as soon as possible and turn off the ignition for 30 seconds. Restart the vehicle and check for the message on the DIC display. If the message still displays or appears again when you begin driving, the system needs service. See your dealer right away. SERVICE TRANSMISSION This message displays when there is a problem with the transmission. See your dealer for service. TRANSMISSION HOT IDLE ENGINE


{ Caution


Do not drive the vehicle while the transmission fluid is overheating, or the transmission can be damaged. This could lead to costly repairs that would not be covered by the warranty.


This message displays and a chime sounds if the transmission fluid in the vehicle gets hot. Driving with the transmission fluid temperature high can cause damage to the vehicle. Stop the vehicle and let it idle to allow the transmission to cool. This message clears when the fluid temperature reaches a safe level.


Vehicle Reminder Messages


ICE POSSIBLE DRIVE WITH CARE This message displays when the outside air temperature is cold enough to create icy road conditions. Adjust your driving accordingly.


GMC Acadia/Acadia Denali Owner Manual (GMNA-Localizing-U.S./Canada/ Mexico-7576030) - 2015 - CRC - 8/18/14


Black plate (42,1)


5-42


Instruments and Controls


Vehicle Speed Messages


SPEED LIMITED TO XXX KM/H (MPH) This message displays when your vehicle speed is limited to 128 km/h (80 mph) because the vehicle detects a problem in the speed variable assist steering system. Have your vehicle serviced by your dealer.


Washer Fluid Messages


WASHER FLUID LOW ADD FLUID This message displays when the windshield washer fluid is low. Fill the windshield washer fluid reservoir as soon as possible. See Engine Compartment Overview on page 10-5 for the location of the windshield washer fluid reservoir. Also, see Washer Fluid on page 10-19 for more information.


Vehicle Personalization Your vehicle may have customization capabilities that allow you to program certain features to one preferred setting. Customization features can only be programmed to one setting on the vehicle and cannot be programmed to a preferred setting for two different drivers. All of the customization options may not be available on your vehicle. Only the options available will be displayed on the DIC. The default settings for the customization features were set when your vehicle left the factory, but may have been changed from their default state since then. The customization preferences are automatically recalled. To change customization preferences, use the following procedure.


Entering the Feature Settings Menu 1. Turn the ignition on and place


the vehicle in P (Park). To avoid excessive drain on the battery, it is recommended that the headlamps are turned off.


2. Press the customization button


to enter the feature settings menu. If the menu is not available, FEATURE SETTINGS AVAILABLE IN PARK will display. Before entering the menu, make sure the vehicle is in P (Park).


Feature Settings Menu Items The following are customization features that allow you to program settings to the vehicle:


DISPLAY IN ENGLISH This feature will only display if a language other than English has been set. This feature allows you to change the language in which the DIC messages appear to English.


GMC Acadia/Acadia Denali Owner Manual (GMNA-Localizing-U.S./Canada/ Mexico-7576030) - 2015 - CRC - 8/18/14


Black plate (43,1)


Press the customization button until the PRESS V TO DISPLAY IN ENGLISH screen appears on the DIC display. Press the set/reset button once to display all DIC messages in English.


DISPLAY LANGUAGE This feature allows you to select the language in which the DIC messages will appear. Press the customization button until the DISPLAY LANGUAGE screen appears on the DIC display. Press the set/reset button once to access the settings for this feature. Then press the customization button to scroll through the following settings: ENGLISH (default): All messages will appear in English. FRANCAIS: All messages will appear in French. ESPANOL: All messages will appear in Spanish.


Instruments and Controls


5-43


NO CHANGE: No change will be made to this feature. The current setting will remain. To select a setting, press the set/ reset button while the desired setting is displayed on the DIC.


AUTO DOOR LOCK This feature allows you to select when the vehicle's doors will automatically lock. See Automatic Door Locks on page 2-7. Press the customization button until AUTO DOOR LOCK appears on the DIC display. Press the set/reset button once to access the settings for this feature. Then press the customization button to scroll through the following settings: SHIFT OUT OF PARK (default): The doors will automatically lock when the vehicle is shifted out of P (Park). AT VEHICLE SPEED: The doors will automatically lock when the vehicle speed is above 13 km/h (8 mph) for three seconds.


NO CHANGE: No change will be made to this feature. The current setting will remain. To select a setting, press the set/ reset button while the desired setting is displayed on the DIC.


AUTO DOOR UNLOCK This feature allows you to select whether or not to turn off the automatic door unlocking feature. It also allows you to select which doors and when the doors will automatically unlock. See Automatic Door Locks on page 2-7. Press the customization button until AUTO DOOR UNLOCK appears on the DIC display. Press the set/reset button once to access the settings for this feature. Then press the customization button to scroll through the following settings: OFF: None of the doors will automatically unlock. DRIVER AT KEY OUT: Only the driver door will unlock when the key is taken out of the ignition.


GMC Acadia/Acadia Denali Owner Manual (GMNA-Localizing-U.S./Canada/ Mexico-7576030) - 2015 - CRC - 8/18/14


Black plate (44,1)


5-44


Instruments and Controls


DRIVER IN PARK: Only the driver door will unlock when the vehicle is shifted into P (Park). ALL AT KEY OUT: All of the doors will unlock when the key is taken out of the ignition. ALL IN PARK (default): All of the doors will unlock when the vehicle is shifted into P (Park). NO CHANGE: No change will be made to this feature. The current setting will remain. To select a setting, press the set/ reset button while the desired setting is displayed on the DIC.


REMOTE DOOR LOCK This feature allows you to select the type of feedback you will receive when locking the vehicle with the Remote Keyless Entry (RKE) transmitter. You will not receive feedback when locking the vehicle with the RKE transmitter if the doors are open. See Remote Keyless Entry (RKE) System Operation on page 2-2.


Press the customization button until REMOTE DOOR LOCK appears on the DIC display. Press the set/reset button once to access the settings for this feature. Then press the customization button to scroll through the following settings: OFF: There will be no feedback when you press the lock button on the RKE transmitter. LIGHTS ONLY: The exterior lamps will flash when you press the lock button on the RKE transmitter. HORN ONLY: The horn will sound on the second press of the lock button on the RKE transmitter. HORN & LIGHTS (default): The exterior lamps will flash when you press the lock button on the RKE transmitter, and the horn will sound when the lock button is pressed again within five seconds of the previous command. NO CHANGE: No change will be made to this feature. The current setting will remain.


To select a setting, press the set/ reset button while the desired setting is displayed on the DIC.


REMOTE DOOR UNLOCK This feature allows you to select the type of feedback you will receive when unlocking the vehicle with the Remote Keyless Entry (RKE) transmitter. You will not receive feedback when unlocking the vehicle with the RKE transmitter if the doors are open. See Remote Keyless Entry (RKE) System Operation on page 2-2. Press the customization button until REMOTE DOOR UNLOCK appears on the DIC display. Press the set/ reset button once to access the settings for this feature. Then press the customization button to scroll through the following settings: LIGHTS OFF: The exterior lamps will not flash when you press the unlock button on the RKE transmitter.


GMC Acadia/Acadia Denali Owner Manual (GMNA-Localizing-U.S./Canada/ Mexico-7576030) - 2015 - CRC - 8/18/14


Black plate (45,1)


Instruments and Controls


5-45


LIGHTS ON (default): The exterior lamps will flash when you press the unlock button on the RKE transmitter. NO CHANGE: No change will be made to this feature. The current setting will remain. To select a setting, press the set/ reset button while the desired setting is displayed on the DIC.


DELAY DOOR LOCK This feature allows you to select whether or not the locking of the vehicle's doors and liftgate will be delayed. When locking the doors and liftgate with the power door lock switch and a door or the liftgate is open, this feature will delay locking the doors and liftgate until five seconds after the last door is closed. You will hear three chimes to signal that the delayed locking feature is in use. The key must be out of the ignition for this feature to work. You can temporarily override delayed locking by pressing the power door lock switch twice or the


lock button on the RKE transmitter twice. See Delayed Locking on page 2-7. Press the customization button until DELAY DOOR LOCK appears on the DIC display. Press the set/reset button once to access the settings for this feature. Then press the customization button to scroll through the following settings: OFF: There will be no delayed locking of the vehicle's doors. ON (default): The doors will not lock until five seconds after the last door or the liftgate is closed. NO CHANGE: No change will be made to this feature. The current setting will remain. To select a setting, press the set/ reset button while the desired setting is displayed on the DIC.


EXIT LIGHTING This feature allows you to select the amount of time you want the exterior lamps to remain on when it


is dark enough outside. This happens after the key is turned from ON/RUN to LOCK/OFF. Press the customization button until EXIT LIGHTING appears on the DIC display. Press the set/reset button once to access the settings for this feature. Then press the customization button to scroll through the following settings: OFF: The exterior lamps will not turn on. 30 SECONDS (default): The exterior lamps will stay on for 30 seconds. 1 MINUTE: The exterior lamps will stay on for one minute. 2 MINUTES: The exterior lamps will stay on for two minutes. NO CHANGE: No change will be made to this feature. The current setting will remain. To select a setting, press the set/ reset button while the desired setting is displayed on the DIC.


GMC Acadia/Acadia Denali Owner Manual (GMNA-Localizing-U.S./Canada/ Mexico-7576030) - 2015 - CRC - 8/18/14


Black plate (46,1)


5-46


Instruments and Controls


APPROACH LIGHTING This feature allows you to select whether or not to have the exterior lights turn on briefly during low light periods after unlocking the vehicle using the Remote Keyless Entry (RKE) transmitter. Press the customization button until APPROACH LIGHTING appears on the DIC display. Press the set/reset button once to access the settings for this feature. Then press the customization button to scroll through the following settings: OFF: The exterior lights will not turn on when you unlock the vehicle with the RKE transmitter. ON (default): If it is dark enough outside, the exterior lights will turn on briefly when you unlock the vehicle with the RKE transmitter. The lights will remain on for 20 seconds or until the lock button on the RKE transmitter is pressed,


or the vehicle is no longer off. See Remote Keyless Entry (RKE) System Operation on page 2-2. NO CHANGE: No change will be made to this feature. The current setting will remain. To select a setting, press the set/ reset button while the desired setting is displayed on the DIC.


CHIME VOLUME This feature allows you to select the volume level of the chime. Press the customization button until CHIME VOLUME appears on the DIC display. Press the set/reset button once to access the settings for this feature. Then press the customization button to scroll through the following settings: NORMAL: The chime volume will be set to a normal level. LOUD: The chime volume will be set to a loud level.


NO CHANGE: No change will be made to this feature. The current setting will remain. There is no default for chime volume. The volume will stay at the last known setting. To select a setting, press the set/ reset button while the desired setting is displayed on the DIC.


PARK TILT MIRRORS If your vehicle has this feature, it allows you to select whether or not the outside mirror(s) will automatically tilt down when the vehicle is shifted into R (Reverse). See Park Tilt Mirrors on page 2-16. Press the customization button until PARK TILT MIRRORS appears on the DIC display. Press the set/reset button once to access the settings for this feature. Then press the customization button to scroll through the following settings: OFF (default): Neither outside mirror will be tilted down when the vehicle is shifted into R (Reverse).


GMC Acadia/Acadia Denali Owner Manual (GMNA-Localizing-U.S./Canada/ Mexico-7576030) - 2015 - CRC - 8/18/14


Black plate (47,1)


Instruments and Controls


5-47


DRIVER MIRROR: The driver outside mirror will be tilted down when the vehicle is shifted into R (Reverse). PASSENGER MIRROR: The passenger outside mirror will be tilted down when the vehicle is shifted into R (Reverse). BOTH MIRRORS: The driver and passenger outside mirrors will be tilted down when the vehicle is shifted into R (Reverse). NO CHANGE: No change will be made to this feature. The current setting will remain. To select a setting, press the set/ reset button while the desired setting is displayed on the DIC.


EASY EXIT SEAT If your vehicle has this feature, it allows you to select your preference for the automatic easy exit seat feature. See Memory Seats on page 3-6.


Press the customization button until EASY EXIT SEAT appears on the DIC display. Press the set/reset button once to access the settings for this feature. Then press the customization button to scroll through the following settings: OFF (default): No automatic seat exit recall will occur. ON: The driver seat will move back when the key is removed from the ignition. The steering column will also move up and forward on vehicles with the power tilt and telescopic steering feature. See Steering Wheel Adjustment on page 5-2. The automatic easy exit seat movement will only occur one time after the key is removed from the ignition. If the automatic movement has already occurred, and you put the key back in the ignition and remove it again, the seat and steering column will stay in the


original exit position, unless a memory recall took place prior to removing the key again. NO CHANGE: No change will be made to this feature. The current setting will remain. To select a setting, press the set/ reset button while the desired setting is displayed on the DIC.


MEMORY SEAT RECALL If your vehicle has this feature, it allows you to select your preference for the remote memory seat recall feature. See Memory Seats on page 3-6. Press the customization button until MEMORY SEAT RECALL appears on the DIC display. Press the set/ reset button once to access the settings for this feature. Then press the customization button to scroll through the following settings: OFF (default): No remote memory seat recall will occur.


GMC Acadia/Acadia Denali Owner Manual (GMNA-Localizing-U.S./Canada/ Mexico-7576030) - 2015 - CRC - 8/18/14


Black plate (48,1)


5-48


Instruments and Controls


ON: The driver seat and outside mirrors will automatically move to the stored driving position when the unlock button on the Remote Keyless Entry (RKE) transmitter is pressed. The steering column will also move on vehicles with the power tilt and telescopic steering feature. See Steering Wheel Adjustment on page 5-2. See “Memory Remote Recall” under Memory Seats on page 3-6 for information on matching transmitters to driver positions. NO CHANGE: No change will be made to this feature. The current setting will remain. To select a setting, press the set/ reset button while the desired setting is displayed on the DIC.


REMOTE START If your vehicle has this feature, it allows you to turn the remote start off or on. The remote start feature allows you to start the engine from outside of the vehicle using the


Remote Keyless Entry (RKE) transmitter. See Remote Vehicle Start on page 2-4. Press the customization button until REMOTE START appears on the DIC display. Press the set/reset button once to access the settings for this feature. Then press the customization button to scroll through the following settings: OFF: The remote start feature will be disabled. ON (default): The remote start feature will be enabled. NO CHANGE: No change will be made to this feature. The current setting will remain. To select a setting, press the set/ reset button while the desired setting is displayed on the DIC.


FACTORY SETTINGS This feature allows you to set all of the customization features back to their factory default settings.


Press the customization button until FACTORY SETTINGS appears on the DIC display. Press the set/reset button once to access the settings for this feature. Then press the customization button to scroll through the following settings: RESTORE ALL (default): The customization features will be set to their factory default settings. DO NOT RESTORE: The customization features will not be set to their factory default settings. To select a setting, press the set/ reset button while the desired setting is displayed on the DIC.


EXIT FEATURE SETTINGS This feature allows you to exit the feature settings menu. Press the customization button until FEATURE SETTINGS PRESS V TO EXIT appears in the DIC display. Press the set/reset button once to exit the menu.


GMC Acadia/Acadia Denali Owner Manual (GMNA-Localizing-U.S./Canada/ Mexico-7576030) - 2015 - CRC - 8/18/14


Black plate (49,1)


Instruments and Controls


5-49


If you do not exit, pressing the customization button again will return you to the beginning of the feature settings menu. Exiting the Feature Settings Menu The feature settings menu will be exited when any of the following occurs:


Universal Remote System See Radio Frequency Statement on page 13-12.


Universal Remote System Programming


The vehicle is shifted out of P (Park). The vehicle is no longer in ON/RUN. The trip/fuel or vehicle information DIC buttons are pressed. The end of the feature settings menu is reached and exited. . A 40-second time period has


elapsed with no selection made.


If equipped, these buttons are in the overhead console. This system can replace up to three remote control transmitters used to activate devices such as garage door openers, security systems, and home automation devices. These instructions refer to a garage door opener, but can be used for other devices.


Do not use the Universal Remote system with any garage door opener that does not have the stop and reverse feature. This includes any garage door opener model manufactured before April 1, 1982. Read these instructions completely before programming the Universal Remote system. It may help to have another person assist with the programming process. Keep the original hand-held transmitter for use in other vehicles as well as for future programming. Erase the programming when vehicle ownership is terminated. See “Erasing Universal Remote System Buttons” later in this section. To program a garage door opener, park outside directly in line with and facing the garage door opener receiver. Clear all people and objects near the garage door.


GMC Acadia/Acadia Denali Owner Manual (GMNA-Localizing-U.S./Canada/ Mexico-7576030) - 2015 - CRC - 8/18/14


Black plate (50,1)


5-50


Instruments and Controls


Make sure the hand-held transmitter has a new battery for quicker and more accurate transmission of the radio-frequency signal. Programming the Universal Remote System For questions or help programming the Universal Remote system, call 1-800-355-3515 or see www.homelink.com. Programming involves time-sensitive actions, and may time out causing the procedure to be repeated. To program up to three devices: 1. Hold the end of the hand-held


transmitter about 3 to 8 cm (1 to 3 in) away from the Universal Remote system buttons with the indicator light in view. The hand-held transmitter was supplied by the manufacturer of the garage door opener receiver.


2. At the same time, press and


hold both the hand-held transmitter button and one of the three Universal Remote system buttons to be used to operate the garage door. Do not release either button until the indicator light changes from a slow to a rapid flash. Then release both buttons. Some garage door openers may require substitution of Step 2
with the procedure under “Radio Signals for Canada and Some Gate Operators” later in this section.


3. Press and hold the newly


programmed Universal Remote system button for five seconds while watching the indicator light and garage door activation.


If the indicator light stays on continuously or the garage door moves when the button is pressed, then


programming is complete. There is no need to complete Steps 4–6. If the indicator light does not come on or the garage door does not move, a second button press may be required. For a second time, press and hold the newly programmed button for five seconds. If the light stays on or the garage door moves, programming is complete. If the indicator light blinks rapidly for two seconds, then changes to a solid light and the garage door does not move, continue with programming Steps 4–6.


GMC Acadia/Acadia Denali Owner Manual (GMNA-Localizing-U.S./Canada/ Mexico-7576030) - 2015 - CRC - 8/18/14


Black plate (51,1)


Instruments and Controls


5-51


enough for the Universal Remote system to pick up the signal during programming. If the programming did not work, replace Step 2 under “Programming the Universal Remote System” with the following: Press and hold the Universal Remote system button while pressing and releasing the hand-held transmitter button every two seconds until the signal has been successfully accepted by the Universal Remote system. The Universal Remote system indicator light will flash slowly at first and then rapidly. Proceed with Step 3 under “Programming the Universal Remote System” to complete.


flash, press and hold the same button a second time for two seconds, then release it. Again, if the door does not move or the garage door lamp does not flash, press and hold the same button a third time for two seconds, then release it.


The Universal Remote system should now activate the garage door. Repeat the process for programming the two remaining buttons. Radio Signals for Canada and Some Gate Operators For questions or programming help, call 1-800-355-3515 or see www.homelink.com. Canadian radio-frequency laws and some U.S. gate operators require transmitter signals to time out or quit after several seconds of transmission. This may not be long


Learn or Smart Button 4. After completing Steps 1–3,


locate the Learn or Smart button inside the garage on the garage door opener receiver. The name and color of the button may vary by manufacturer.


5. Press and release the Learn or


6.


Smart button. Step 6 must be completed within 30 seconds of pressing this button. Inside the vehicle, press and hold the newly programmed Universal Remote system button for two seconds, then release it. If the garage door does not move or the lamp on the garage door opener receiver does not


GMC Acadia/Acadia Denali Owner Manual (GMNA-Localizing-U.S./Canada/ Mexico-7576030) - 2015 - CRC - 8/18/14


Black plate (52,1)


5-52


Instruments and Controls


Reprogramming a Single Universal Remote System Button To reprogram any of the system buttons: 1. Press and hold any one of the


buttons. Do not release the button.


2. The indicator light will begin to flash after 20 seconds. Without releasing the button, proceed with Step 1 under “Programming the Universal Remote System.”


Universal Remote System Operation


Using the Universal Remote System Press and hold the appropriate Universal Remote system button for at least one-half second. The indicator light will come on while the signal is being transmitted. Erasing Universal Remote System Buttons Erase all programmed buttons when vehicle ownership is terminated. To erase: 1. Press and hold the two outside buttons until the indicator light begins to flash. This should take about 10 seconds.


2. Release both buttons.


GMC Acadia/Acadia Denali Owner Manual (GMNA-Localizing-U.S./Canada/ Mexico-7576030) - 2015 - CRC - 8/18/14


Black plate (1,1)


Lighting


Exterior Lighting


Exterior Lamp Controls . . . . . . . . 6-1
Headlamp High/Low-Beam


Changer . . . . . . . . . . . . . . . . . . . . . 6-2
Flash-to-Pass . . . . . . . . . . . . . . . . . 6-2
Daytime Running Lamps


(DRL)/Automatic Headlamp System . . . . . . . . . . . . . . . . . . . . . . 6-2
Delayed Headlamps . . . . . . . . . . 6-3
Hazard Warning Flashers . . . . . 6-3
Turn and Lane-Change


Signals . . . . . . . . . . . . . . . . . . . . . . 6-4
Fog Lamps . . . . . . . . . . . . . . . . . . . . 6-4


Interior Lighting


Instrument Panel Illumination


Control . . . . . . . . . . . . . . . . . . . . . . 6-5
Courtesy Lamps . . . . . . . . . . . . . . 6-5
Dome Lamps . . . . . . . . . . . . . . . . . 6-5
Reading Lamps . . . . . . . . . . . . . . . 6-6


Lighting


6-1


Exterior Lighting


Exterior Lamp Controls


Lighting Features


Entry Lighting . . . . . . . . . . . . . . . . . 6-6
Delayed Entry Lighting . . . . . . . . 6-7
Delayed Exit Lighting . . . . . . . . . 6-7
Parade Dimming . . . . . . . . . . . . . . 6-7
Battery Load Management . . . . 6-7
Battery Power Protection . . . . . . 6-8


The exterior lamp control is on the instrument panel to the left of the steering wheel. There are four positions: O (Off): Briefly turn to this position to turn the automatic light control off or on again. AUTO (Automatic): Turns the headlamps on automatically at normal brightness, together with the other exterior lamps and instrument panel lights.


GMC Acadia/Acadia Denali Owner Manual (GMNA-Localizing-U.S./Canada/ Mexico-7576030) - 2015 - CRC - 8/18/14


Black plate (2,1)


6-2


Lighting


; (Parking Lamps): Turns on the parking lamps including all lamps, except the headlamps. 5 (Headlamps): Turns on the headlamps together with the parking lamps and instrument panel lights. A warning chime sounds if the driver door is opened when the ignition switch is off and the headlamps are on. # (Fog Lamps): turns the fog lamps on or off. See Fog Lamps on page 6-4.


If equipped, it


Headlamp High/ Low-Beam Changer 2 3 (Headlamp High/Low-Beam Changer): Push the turn signal lever away from you to turn the high beams on. Pull the lever toward you to return to low beams.


This indicator light turns on in the instrument cluster when the high-beam headlamps are on.


Flash-to-Pass This feature is used to signal to the vehicle ahead that you want to pass. If the headlamps are off or in the low-beam position, pull the turn signal lever toward you to momentarily switch to high beams. Release the lever to turn the high-beam headlamps off.


Daytime Running Lamps (DRL)/Automatic Headlamp System DRL can make it easier for others to see the front of your vehicle during the day. Fully functional DRL are required on all vehicles first sold in Canada. The DRL system makes the low-beam headlamps come on at a reduced brightness when the following conditions are met:


The ignition is in the ON/RUN position. The exterior lamp control is in AUTO. The engine is running.


When the DRL are on, the regular headlamps, taillamps, sidemarker, and other lamps will not be on. The instrument cluster will not be lit.


GMC Acadia/Acadia Denali Owner Manual (GMNA-Localizing-U.S./Canada/ Mexico-7576030) - 2015 - CRC - 8/18/14


Black plate (3,1)


The headlamps automatically change from DRL to the regular headlamps depending on the darkness of the surroundings. The other lamps that come on with the headlamps will also come on. When it is bright enough outside, the headlamps will go off and the DRL will come on. The regular headlamp system should be turned on when needed. Do not cover the light sensor on top of the instrument panel because it works with the DRL.


Delayed Headlamps Delayed headlamps provide a period of exterior lighting as you leave the area around the vehicle. This feature is activated when the headlamps are on due to the automatic headlamps control feature and when the ignition is turned off. The headlamps remain on until the exterior lamp control is moved to the parking lamps position or until the pre-selected delayed headlamp lighting period has ended. If the ignition is turned off with the exterior lamp control in the ; or 5 position, the delayed headlamps cycle will not occur. To disable the delayed headlamps feature or change the time of delay, see Vehicle Personalization on page 5-42.


Lighting


6-3


Hazard Warning Flashers


| (Hazard Warning Flasher): Press this button to make the front and rear turn signal lamps flash on and off. This warns others that you are having trouble. Press again to turn the flashers off. The turn signals do not work while the hazard warning flashers are on.


GMC Acadia/Acadia Denali Owner Manual (GMNA-Localizing-U.S./Canada/ Mexico-7576030) - 2015 - CRC - 8/18/14


Black plate (4,1)


6-4


Lighting


Turn and Lane-Change Signals


Move the turn signal lever all the way up or down to signal a turn. An arrow on the instrument cluster flashes in the direction of the turn or lane change. Raise or lower the lever until the arrow starts to flash to signal a lane change. Hold it there until the lane change is completed. If the lever is briefly pressed and released, the turn signal flashes three times. The lever returns to its starting position whenever it is released.


If after signaling a turn or lane change the arrow flashes rapidly or does not come on, a signal bulb may be burned out. Have any burned out bulbs replaced. If a bulb is not burned out, check the fuse. See Fuses and Circuit Breakers on page 10-28. Turn Signal On Chime If either one of the turn signals is left on and the vehicle has been driven more than 1.2 km (0.75 mi), a chime will sound.


Fog Lamps


The fog lamp button is on the exterior lamp control to the left of the steering column. # (Fog Lamps): Press this button to turn the fog lamps on or off. A light comes on in the instrument cluster when the fog lamps are in use. The ignition must be on for the fog lamps to work. When the headlamps are changed to high beam, the fog lamps turn off. The fog lamps come back on again when the high-beam headlamps are turned off. Some localities have laws that require the headlamps to be on along with the fog lamps.


Use the fog lamps for better vision in foggy or misty conditions.


GMC Acadia/Acadia Denali Owner Manual (GMNA-Localizing-U.S./Canada/ Mexico-7576030) - 2015 - CRC - 8/18/14


Black plate (5,1)


Lighting


6-5


Dome Lamps The dome lamps are in the overhead console and above the rear seat passengers. The dome lamps come on when a door is opened, unless the dome lamp override button is pressed in. The lamps can also be turned on and off by turning the instrument panel brightness control clockwise to the farthest position.


Interior Lighting


Instrument Panel Illumination Control


The instrument panel brightness knob is located on the instrument panel to the left of the steering column.


D (Instrument Panel Brightness): Push the knob in all the way until it extends out and then turn the knob clockwise or counterclockwise to brighten or dim the lights. Push the knob back in when finished.


Courtesy Lamps The courtesy lamps automatically come on when a door is opened. The lamps can also be turned on manually by fully turning the instrument panel brightness control clockwise. The reading lamps, located on the headliner above the rearview mirror, can be turned on or off independently of the automatic courtesy lamps, when the doors are closed.


GMC Acadia/Acadia Denali Owner Manual (GMNA-Localizing-U.S./Canada/ Mexico-7576030) - 2015 - CRC - 8/18/14


Black plate (6,1)


6-6


Lighting


Dome Lamp Override


The dome lamp override button is next to the exterior lamps control. E DOME OFF (Dome Lamp Override): Press the button and the dome lamps remain off when a door is opened. An indicator light on the button comes on to show that the dome lamps are off. Press the button again so the dome lamps come on when a door is opened.


AMBIENT OFF (If Equipped): Press the button to turn the ambient lights off. Press the button again to turn ambient lights on.


Reading Lamps Press the button near each lamp to turn them on or off.


Lighting Features


Entry Lighting For vehicles with courtesy lamps, they come on and stay on for a set time whenever K is pressed on the Remote Keyless Entry (RKE) transmitter. If a door is opened, the lamps stay on while it is open and then turn off automatically about 20 seconds after the door is closed. If K is pressed and no door is opened, the lamps turn off after about 20 seconds. Entry lighting includes a feature called theater dimming. With theater dimming, the lamps do not turn off at the end of the delay time. Instead, they slowly dim and then go out. The delay time is canceled if the ignition key is turned to ON/RUN or the power door lock switch is pressed. The lamps will dim right away.


GMC Acadia/Acadia Denali Owner Manual (GMNA-Localizing-U.S./Canada/ Mexico-7576030) - 2015 - CRC - 8/18/14


Black plate (7,1)


When the ignition is on, illuminated entry is inactive, which means the courtesy lamps will not come on unless a door is opened.


Delayed Entry Lighting Delayed entry lighting illuminates the interior for a period of time after all the doors have been closed. The ignition must be off for delayed entry lighting to work. Immediately after all the doors have been closed, the delayed entry lighting feature continues to work until one of the following occurs:


The ignition is in ON/RUN. The doors are locked.


. An illumination period of about


25 seconds has elapsed.


If during the illumination period a door is opened, the timed illumination period is canceled and the interior lamps remain on.


Delayed Exit Lighting Delayed exit lighting illuminates the interior for a period of time after the key is removed from the ignition. The ignition must be off for delayed exit lighting to work. When the key is removed, interior illumination activates and remains on until one of the following occurs:


The ignition is in ON/RUN. The power door locks are activated.


. An illumination period of 20 seconds has elapsed.


If during the illumination period a door is opened, the timed illumination period will be canceled and the interior lamps will remain on because a door is open.


Lighting


6-7


Parade Dimming This feature automatically prohibits the dimming of the instrument panel displays in daylight while the headlamps are on so that the displays are still able to be seen.


Battery Load Management The vehicle has Electric Power Management (EPM) that estimates the battery's temperature and state of charge. It then adjusts the voltage for best performance and extended life of the battery. When the battery's state of charge is low, the voltage is raised slightly to quickly bring the charge back up. When the state of charge is high, the voltage is lowered slightly to prevent overcharging. If the vehicle has a voltmeter gauge or a voltage display on the Driver Information Center (DIC), you may see the


GMC Acadia/Acadia Denali Owner Manual (GMNA-Localizing-U.S./Canada/ Mexico-7576030) - 2015 - CRC - 8/18/14


Black plate (8,1)


6-8


Lighting


voltage move up or down. This is normal. If there is a problem, an alert will be displayed. The battery can be discharged at idle if the electrical loads are very high. This is true for all vehicles. This is because the generator (alternator) may not be spinning fast enough at idle to produce all of the power needed for very high electrical loads. A high electrical load occurs when several of the following are on, such as: headlamps, high beams, rear window defogger, climate control fan at high speed, heated seats, engine cooling fans, trailer loads, and loads plugged into accessory power outlets. EPM works to prevent excessive discharge of the battery. It does this by balancing the generator's output and the vehicle's electrical needs.


It can increase engine idle speed to generate more power whenever needed. It can temporarily reduce the power demands of some accessories. Normally, these actions occur in steps or levels, without being noticeable. In rare cases at the highest levels of corrective action, this action may be noticeable to the driver. If so, a DIC message might be displayed, such as BATTERY SAVER ACTIVE, BATTERY VOLTAGE LOW, or LOW BATTERY. If one of these messages displays, it is recommended that the driver reduce the electrical loads as much as possible. See Driver Information Center (DIC) on page 5-23.


Battery Power Protection This feature helps prevent the battery from being drained, if the interior courtesy lamps or reading lamps are accidentally left on. If any of these lamps are left on, they automatically turn off after 10 minutes, if the ignition is off. The lamps will not come back on again until one of the following occurs:


The ignition is turned on. The exterior lamps control is turned off, then on again.


The headlamps will time out after 10 minutes, if they are manually turned on while the ignition is on or off.


GMC Acadia/Acadia Denali Owner Manual (GMNA-Localizing-U.S./Canada/ Mexico-7576030) - 2015 - CRC - 8/18/14


Black plate (1,1)


Phone


Bluetooth . . . . . . . . . . . . . . . . . . . . 7-18


Settings


Settings . . . . . . . . . . . . . . . . . . . . . . 7-25


Trademarks and License Agreements


Trademarks and License


Agreements . . . . . . . . . . . . . . . . 7-27


Infotainment System


Introduction


Infotainment . . . . . . . . . . . . . . . . . . . 7-1
Theft-Deterrent Feature . . . . . . . 7-2
Overview . . . . . . . . . . . . . . . . . . . . . . 7-3
Operation . . . . . . . . . . . . . . . . . . . . . 7-3


Radio


AM-FM Radio . . . . . . . . . . . . . . . . . 7-6
Satellite Radio . . . . . . . . . . . . . . . . 7-9
Radio Reception . . . . . . . . . . . . . 7-10
Multi-Band Antenna . . . . . . . . . . 7-11


Audio Players


CD Player . . . . . . . . . . . . . . . . . . . . 7-11
MP3 . . . . . . . . . . . . . . . . . . . . . . . . . 7-13
Auxiliary Devices . . . . . . . . . . . . 7-15


Rear Seat Infotainment


Rear Seat Audio (RSA)


System . . . . . . . . . . . . . . . . . . . . . 7-16


Rear Audio


Controller (RAC) . . . . . . . . . . . 7-17


Infotainment System 7-1


Introduction


Infotainment Base radio information is included in this manual. See the infotainment manual for information on other available infotainment systems. Read the following pages to become familiar with these features.


{ Warning


Taking your eyes off the road for too long or too often while using any infotainment feature can cause a crash. You or others could be injured or killed. Do not give extended attention to infotainment tasks while driving. Limit your glances at the vehicle displays and focus your attention on driving. Use voice commands whenever possible.


GMC Acadia/Acadia Denali Owner Manual (GMNA-Localizing-U.S./Canada/ Mexico-7576030) - 2015 - CRC - 8/18/14


Black plate (2,1)


7-2


Infotainment System


The infotainment system has built-in features intended to help avoid distraction by disabling some functions when driving. These functions may gray out when they are unavailable. Many infotainment features are also available through the instrument cluster and steering wheel controls. Before driving: . Become familiar with the


operation, faceplate buttons, and screen buttons.


. Set up the audio by presetting


favorite stations, setting the tone, and adjusting the speakers.


. Set up phone numbers in


advance so they can be called easily by pressing a single button or by using a single voice command if equipped with Bluetooth phone capability.


See Defensive Driving on page 9-3. To play the infotainment system with the ignition off, see Retained Accessory Power (RAP) on page 9-19.


Theft-Deterrent Feature TheftLock® is designed to discourage theft of the vehicle's radio by learning a portion of the Vehicle Identification Number (VIN). The radio does not operate if it is stolen or moved to a different vehicle.


GMC Acadia/Acadia Denali Owner Manual (GMNA-Localizing-U.S./Canada/ Mexico-7576030) - 2015 - CRC - 8/18/14


Black plate (3,1)


Overview


The infotainment system is controlled by using the buttons, touch screen, steering wheel controls, and voice recognition. See Operation on page 7-3.


1. PUSH/O (Volume/Power) 2. Z (Eject) 3. CD Slot 4. AUX Port


5. PUSH/SEL (Select) 6. D (Home Page) 7. SRCE (Source) 8. FAV (Favorites Menu)


Infotainment System 7-3


9. © SEEK (Previous/Reverse) 10. SEEK ¨ (Next/Forward) 11. / BACK


Operation


Infotainment Controls PUSH/ O (Volume/Power): . Press to turn the system on


and off. Turn to adjust the volume.


Z (Eject): Press to eject a disc from the CD player. See CD Player on page 7-11. AUX Port: 3.5 mm (1/8 in) connection for external audio devices. PUSH/SEL(Select):


Turn to manually find a station or highlight a menu selection.


. Press to select a highlighted


selection.


GMC Acadia/Acadia Denali Owner Manual (GMNA-Localizing-U.S./Canada/ Mexico-7576030) - 2015 - CRC - 8/18/14


Black plate (4,1)


7-4


Infotainment System


D (Home Page): Press to go to the Home Page. See “Home Page” in this section. SRCE (Source): Press to switch between AM, FM, CD, and if equipped, SiriusXM®, front auxiliary, rear auxiliary, and iPod/USB. Press and hold to mute/pause the system. Press and hold again to unmute/resume the system. FAV (Favorites Menu): or SiriusXM, press to change the current favorite page number above the preset buttons. Keep pressing to scroll through the favorites pages. The stored stations for each list display on the bottom of the screen. The number of preset Favorite Pages can be changed by pressing the Settings button on a Home Page, then pressing Favorites Pages, and then selecting the number of Favorite Pages.


In AM, FM,


© SEEK (Previous/Reverse): . AM, FM, SiriusXM (if equipped):


Press to seek to the previous strong station. Press and hold for Scan. Press © again to stop the scan.


. CD, USB: Press to seek to the


beginning of the current or previous track.


. CD, USB: Press and hold to


quickly reverse through a track. Release the button to return to playing speed. See CD Player on page 7-11 and Auxiliary Devices on page 7-15. SEEK ¨ (Next/Forward): . AM, FM, SiriusXM (if equipped): Press to seek to the next strong station. Press and hold for Scan. Press ¨ again to stop the scan.


. CD, USB: Press to seek or skip


the next track or program.


. CD, USB: Press and hold to fast forward through a track. Release the button to return to playing speed. See CD Player on page 7-11 and Auxiliary Devices on page 7-15.


/ BACK: Press to return to the previous screen in a menu. Touchscreen Buttons Touchscreen buttons show visibly on the screen when available. When a function is unavailable, the button may gray-out. When a function is selected, the button may highlight, or animate.


GMC Acadia/Acadia Denali Owner Manual (GMNA-Localizing-U.S./Canada/ Mexico-7576030) - 2015 - CRC - 8/18/14


Black plate (5,1)


Home Page


The infotainment system displays a Home Page to access all of the applications. Back: Press to go back to the previous page or menu. Home: From any page, press to cycle through the Home Pages to start a different application. The Home Page can have up to three pages with eight icons per page. Each of these three pages can be customized to contain your choice of up to eight per screen. They may also be re-ordered on each screen to taste.


FAV (Favorites): Press to scroll through the favorites banner on the bottom of the screen. The favorites banner stores your favorite radio and SiriusXM stations. To store a favorite station, press and hold on the desired position on the banner until a beep is heard. g (Voice Recognition): Press to begin voice recognition. See Bluetooth on page 7-18. Menu: Press to enter the Home Page menu. q Previous : Press to go to the previous Home Page. Next r : Press to go to the next Home Page. Home Page Features Some features are disabled when the vehicle is moving and some icons may not be active.


Infotainment System 7-5


Now Playing: Press to display the active source page. The sources available are AM, FM, XM (if equipped), CD, USB, Bluetooth, or AUX Input. Settings: Press to display the Settings menu. See Settings on page 7-25. Tone: Press to display the Tone Settings menu. The following may display: Tone Settings: Press to adjust the tone settings. The following may display: . EQ: Press o or p to adjust the


equalizer.


. Bass: Press + or − to adjust


the bass.


. Middle: Press + or − to adjust


the middle. Treble: Press + or − to adjust the treble.


GMC Acadia/Acadia Denali Owner Manual (GMNA-Localizing-U.S./Canada/ Mexico-7576030) - 2015 - CRC - 8/18/14


Black plate (6,1)


7-6


Infotainment System


. Balance: Press L to hear more sound from the left speakers or R for more sound from the right speakers. The middle position balances the sound between the left and right speakers. Fade: Press F for more sound from the front speakers or R for more sound from the rear speakers. The middle position balances the sound between the front and rear speakers.


DSP Mode: Press o or p to adjust the DSP mode (if equipped). Language To change the language of the screens. See Vehicle Personalization on page 5-42. English or Metric Units To change the screens from English or metric. See Driver Information

Loading...
x