2013 GMC Acadia Owners Manual

transmitter functions work up to 60 m (195 ft) away from the vehicle. There are other conditions which can affect the performance of the transmitter. See Remote Keyless Entry (RKE) System on page 2‑2.

The key is used for the ignition and all door locks. The key has a bar-coded key tag that the dealer or qualified locksmith can use to make new keys. Store this information in a safe place, not in the vehicle. If it becomes difficult to turn the key, inspect the key blade for debris. See your dealer if a replacement key or additional key is needed.

Acadia/Acadia Denali Owner Manual - 2013 - crc2 - 12/11/12

Black plate (3,1)

Keys, Doors, and Windows

2-3

five seconds. See Vehicle Personalization on page 5‑41 for additional information. Pressing Q may arm the content theft-deterrent system. See Vehicle Alarm System on page 2‑11. K (Unlock): Press once to unlock only the driver door. If K is pressed again within five seconds, all remaining doors unlock. The interior lamps come on and stay on for 20 seconds or until the ignition is turned on. If enabled through the DIC, the parking lamps flash twice to indicate unlocking has occurred. See Vehicle Personalization on page 5‑41. Pressing K on the RKE transmitter disarms the content theft-deterrent system. See Vehicle Alarm System on page 2‑11. 8 (Power Liftgate): Press and hold until the liftgate begins to move to open or close the liftgate. The

taillamps flash and a chime sounds to indicate when the liftgate is opening or closing. L (Vehicle Locator/Panic Alarm): Press and release to locate the vehicle. The parking lamps flash and the horn sounds three times. Press and hold L for more than two seconds to activate the panic alarm. The parking lamps flash and the horn sounds repeatedly for 30 seconds. The alarm turns off when the ignition is moved to ON/ RUN or L is pressed again. The ignition must be in LOCK/OFF for the panic alarm to work. Programming Transmitters to the Vehicle Only RKE transmitters programmed to this vehicle will work. If a transmitter is lost or stolen, a replacement can be purchased and programmed through your dealer. When the replacement transmitter is programmed to this vehicle, all

With Remote Start and Power Liftgate Shown, Without Similar

/ (Remote Vehicle Start): For vehicles with this feature, see Remote Vehicle Start on page 2‑4
for additional information. Q (Lock): Press to lock all the doors. If enabled through the Driver Information Center (DIC), the parking lamps flash once to indicate locking has occurred. If enabled through the DIC, the horn sounds when Q is pressed again within

Acadia/Acadia Denali Owner Manual - 2013 - crc2 - 12/11/12

Black plate (4,1)

2-4

Keys, Doors, and Windows

remaining transmitters must also be reprogrammed. Any lost or stolen transmitters will no longer work once the new transmitter is programmed. Each vehicle can have up to eight transmitters programmed to it. See your dealer to program transmitters to this vehicle. Battery Replacement Replace the battery if the REPLACE BATTERY IN REMOTE KEY message displays in the DIC. Notice: When replacing the battery, do not touch any of the circuitry on the transmitter. Static from your body could damage the transmitter.

3.

Insert the new battery, positive side facing down. Replace with a CR2032 or equivalent battery.

4. Snap the transmitter back

together.

Remote Vehicle Start This vehicle may have a remote starting feature that starts the engine from outside of the vehicle. / (Remote Start): This button is located on the RKE transmitter if the vehicle has remote start. Laws in some communities may restrict the use of remote starters. For example, some laws may require a person using the remote start to have the vehicle in view when doing so. Check local regulations for any requirements on remote starting of vehicles. Do not use the remote start feature if the vehicle is low on fuel. The vehicle could run out of fuel.

1. Separate the transmitter with a

flat, thin object, such as a flat head screwdriver.

Carefully insert the tool into the notch located along the parting line of the transmitter. Do not insert the tool too far. Stop as soon as resistance is felt. Twist the tool until the transmitter is separated.

2. Remove the old battery. Do not

use a metal object.

Acadia/Acadia Denali Owner Manual - 2013 - crc2 - 12/11/12

Black plate (5,1)

Keys, Doors, and Windows

2-5

If the vehicle has the remote start feature, the RKE transmitter range may be less while the vehicle is running. There are other conditions that can affect the performance of the transmitter. See Remote Keyless Entry (RKE) System on page 2‑2 for additional information. Starting the Engine Using Remote Start To start the vehicle: 1. Aim the RKE transmitter at the

vehicle.

2. Press and release Q on the

3.

RKE transmitter. Immediately after completing Step 2, press and hold / until the parking lamps flash. If the vehicle's lights cannot be seen, press and hold / for at least four seconds.

When the vehicle starts, the parking lamps will turn on and remain on as long as the engine is running. The doors will be locked and the climate control system will operate automatically if the vehicle has the automatic system, or at the same setting as when the vehicle was last turned off. If the vehicle has an automatic climate control system and heated seats, the heated seats turn on during colder outside temperatures and shut off when the key is turned to ON/RUN. See Heated and Ventilated Front Seats on page 3‑8
for more information. The rear window defogger and heated mirrors, if the vehicle has them, turn on during colder outside temperatures and turn off when the key is turned to ON/RUN. After entering the vehicle during a remote start, insert and turn the key to the ON/RUN position to drive the vehicle.

If the vehicle is left running it automatically shuts off after 10 minutes unless a time extension has been done. Extending Engine Run Time To extend the engine run time by 10 minutes, repeat Steps 1–3 while the engine is still running. The engine run time can only be extended if it is the first remote start since the vehicle has been driven. Remote start can be extended one time. If the remote start procedure is used again before the first 10-minute time frame has ended, the first 10 minutes will immediately expire and the second 10-minute time frame will start. For example, if Q and then / are pressed again after the vehicle has been running for five minutes, 10 minutes are added, allowing the engine to run for a total of 15 minutes.

Acadia/Acadia Denali Owner Manual - 2013 - crc2 - 12/11/12

Black plate (6,1)

2-6

Keys, Doors, and Windows

A maximum of two remote starts or remote start attempts are allowed between ignition cycles. After the vehicle's engine has been started two times using the remote start button, the ignition must be turned on and then back off before the remote start procedure can be used again. Canceling a Remote Start To manually shut off a remote start: . Aim the RKE transmitter at the vehicle and press / until the parking lamps turn off. Turn on the hazard warning flashers. Turn the ignition switch on and then off.

Conditions in Which the Remote Start Will Not Work The vehicle cannot be started using the remote start feature if the key is in the ignition, the hood is open, or if there is an emission control system malfunction. The engine turns off during a remote start if the coolant temperature gets too high or if the oil pressure gets low.

Door Locks

{ WARNING Unlocked doors can be dangerous.

. Passengers, especially

children, can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle will not open it. The chance of being thrown out of the vehicle in a

(Continued)

WARNING (Continued)

crash is increased if the doors are not locked. So, all passengers should wear safety belts properly and the doors should be locked whenever the vehicle is driven.

. Young children who get into

unlocked vehicles may be unable to get out. A child can be overcome by extreme heat and can suffer permanent injuries or even death from heat stroke. Always lock the vehicle whenever leaving it.

. Outsiders can easily enter through an unlocked door when you slow down or stop the vehicle. Locking the doors can help prevent this from happening.

To lock or unlock a door, use the key from the outside or the door lock from the inside.

Acadia/Acadia Denali Owner Manual - 2013 - crc2 - 12/11/12

Black plate (7,1)

Power Door Locks

Base Model

Uplevel Model

Keys, Doors, and Windows

2-7

K (Unlock): Press to unlock the doors. Q (Lock): Press to lock the doors.

Delayed Locking When locking the doors with the power lock switch and a door or the liftgate is open, the doors will lock five seconds after the last door is closed. You will hear three chimes to signal that the delayed locking feature is in use. Pressing the power lock switch twice or the lock button on the RKE transmitter twice will override the delayed locking feature and immediately lock all the doors. This feature will not operate if the key is in the ignition. This feature can be programmed by using the Driver Information Center (DIC). See “DELAY DOOR LOCK” under Vehicle Personalization on page 5‑41.

Automatic Door Locks Vehicles with an automatic lock/ unlock feature enable you to program the vehicle's power door locks. This feature can be programmed through the Driver Information Center (DIC). See Vehicle Personalization on page 5‑41 for more information.

Lockout Protection This feature protects you from locking the key in the vehicle when the key is in the ignition and a front door is open. If the driver side power door lock switch is pressed when the driver door is open and the key is in the ignition, all of the doors will lock and then the driver door will unlock. If the passenger side power door lock switch is pressed when the front passenger door is open and the key is in the ignition, all of the doors will lock and then the front passenger door will unlock.

Acadia/Acadia Denali Owner Manual - 2013 - crc2 - 12/11/12

Black plate (8,1)

2-8

Keys, Doors, and Windows

Safety Locks The vehicle has rear door security locks to prevent passengers from opening the rear doors from the inside.

To set the locks, insert a key into the slot and turn it to the horizontal position. The door can only be opened from the outside with the door unlocked. To return the door to normal operation, turn the slot to the vertical position.

Doors

Liftgate

Manual Liftgate

{ WARNING

Open the rear doors to access the security locks on the inside edge of each door.

Exhaust gases can enter the vehicle if it is driven with the liftgate or trunk/hatch open, or with any objects that pass through the seal between the body and the trunk/hatch or liftgate. Engine exhaust contains carbon monoxide (CO) which cannot be seen or smelled. It can cause unconsciousness and even death. If the vehicle must be driven with the liftgate or trunk/hatch open:

. Close all of the windows. . Fully open the air outlets on

or under the instrument panel.

(Continued)

Acadia/Acadia Denali Owner Manual - 2013 - crc2 - 12/11/12

Black plate (9,1)

Keys, Doors, and Windows

2-9

To open the liftgate, press the touch pad under the liftgate handle and lift up. The vehicle must be in P (Park) and the battery must be charged. Use the pull cup to lower and close the liftgate. Always close the liftgate before driving. Power Liftgate On vehicles with a power liftgate, the vehicle must be in P (Park) to operate. The taillamps flash and a chime sounds when the power liftgate moves.

{ WARNING

You, or others, could be injured if caught in the path of the power liftgate. Make sure there is no one in the way of the liftgate as it is opening and closing.

WARNING (Continued)

. Adjust the climate control

system to a setting that brings in only outside air and set the fan speed to the highest setting. See “Climate Control Systems” in the Index.

. If the vehicle is equipped with

a power liftgate, disable the power liftgate function.

See Engine Exhaust on page 9‑20.

Notice: To avoid damage to the liftgate or liftgate glass, make sure the area above and behind the liftgate is clear before opening it. To unlock the liftgate, press the power door lock switch or press K on the Remote Keyless Entry (RKE) transmitter twice. See Remote Keyless Entry (RKE) System Operation on page 2‑2.

The power liftgate can be power opened and closed in the following ways: . Press and hold 8 on the

RKE transmitter. See Remote Keyless Entry (RKE) System Operation on page 2‑2.

. Press O. . Press the touch pad on the

outside liftgate handle.

Pressing the buttons or touch pad a second time while the liftgate is moving reverses the direction.

Acadia/Acadia Denali Owner Manual - 2013 - crc2 - 12/11/12

Black plate (10,1)

2-10

Keys, Doors, and Windows

continue to completion. If the vehicle is shifted out of P (Park) and accelerated before the power liftgate latch closes, the liftgate may reverse to the open position. Cargo could fall out of the vehicle. Always make sure the power liftgate is closed and latched before driving away. If the power liftgate is used and the liftgate support struts have lost pressure, the taillamps will flash and a chime will sound. The liftgate will stay open temporarily, and then slowly close. See a dealer for service before using the liftgate if this occurs.

Obstacle Detection Features A warning chime will sound and the liftgate will automatically reverse direction to the full closed or open position if an obstacle is encountered during a power open or close cycle. After removing the obstacle the liftgate will resume normal operation.

If more obstacles are encountered on the same power cycle, the power function deactivates, and the liftgate must be opened or closed manually. A message displays on the Driver Information Center (DIC) to indicate that the liftgate is open. See Door Ajar Messages on page 5‑32. After removing the obstacles, manually open the liftgate fully or close and latch the liftgate. The liftgate will resume normal power operation. The vehicle has pinch sensors located on the side edges of the liftgate. If an object is caught between the liftgate and the body of the vehicle and presses against a sensor, the liftgate will reverse direction and open fully. The liftgate will remain open until it is activated again or closed manually. Do not force the liftgate open or closed during a power cycle.

Power Liftgate Touch Pad

The liftgate can also be closed by pressing l next to the liftgate latch. Press l a second time during the liftgate operation to reverse the operation. The power liftgate may be temporarily disabled under extreme temperatures or under low battery conditions. If this occurs, the liftgate can be operated manually. If the vehicle is shifted out of P (Park) while the liftgate power function is in progress, it will

Acadia/Acadia Denali Owner Manual - 2013 - crc2 - 12/11/12

Black plate (11,1)

Keys, Doors, and Windows

2-11

Vehicle Security This vehicle has theft-deterrent features; however, they do not make the vehicle impossible to steal.

Vehicle Alarm System On vehicles with an anti-theft alarm system, to activate the system: . Press Q on the Remote Keyless

Entry (RKE) transmitter or the power door lock switch when any door is open.

To open the liftgate, press the touch pad on the outside of the liftgate handle and lift up. Use the pull handle to lower and close the liftgate; the liftgate latch will power close. Always close the liftgate before driving. If 8 on the RKE transmitter or l on the liftgate is pressed while in manual operation mode, the taillamps will flash three times, but the liftgate will not move. It is not recommended to drive with the liftgate open. However, if the vehicle must be driven with the liftgate open, the liftgate should be set to manual operation.

Manual Operation of Power Liftgate

To change the liftgate to manual operation, press OFF on the power liftgate switch. A message displays on the DIC indicating manual operation mode. See Door Ajar Messages on page 5‑32. With the liftgate in manual mode and all of the doors unlocked, the liftgate can be manually opened and closed.

Acadia/Acadia Denali Owner Manual - 2013 - crc2 - 12/11/12

Black plate (12,1)

2-12

Keys, Doors, and Windows

The security light flashes. When the door is closed, the security light stops flashing and stays on solid for approximately 30 seconds. The content theft-deterrent alarm is not armed until the security light goes off. If the delayed locking feature is active, the alarm is not activated until all doors are closed and the security light goes off.

. Press Q when the driver door is closed. The security light comes on solid for approximately 30 seconds and then goes off. The content theft-deterrent alarm is not armed until the security light goes off.

The theft-deterrent system will not activate if the doors are locked with the vehicle's key or the manual door lock. If a locked door is opened without using the RKE transmitter, a 10-second pre-alarm occurs. The

horn chirps and the lights flash. If the key is not placed in the ignition and turned to START or the door is not unlocked by pressing Q during the 10-second pre-alarm, the alarm goes off. The headlamps flash and the horn sounds for about 30 seconds, then turns off to save the battery power. The vehicle can be started with the correct ignition key if the alarm has been set off. To avoid setting off the alarm by accident:

Lock the vehicle with the door key after the doors are closed. . Unlock the door with the RKE

transmitter. Unlocking a door any other way sets off the alarm if the system has been armed. Press K or place the key in the ignition and turn it to START to turn off the alarm.

Testing the Alarm To test the alarm: 1. From inside the vehicle, lower

the driver side window, and open the driver door.

2. Press Q. 3. Get out of the vehicle, close the

door, and wait for the security light to go out.

4. Reach in through the window,

unlock the door with the manual door lock, and open the door. This should set off the alarm.

If the alarm does not sound when it should, but the headlamps flash, check to see if the horn works. The horn fuse may be blown. To replace the fuse, see Fuses and Circuit Breakers on page 10‑28. If the alarm does not sound or the headlamps do not flash, see your dealer for service.

Acadia/Acadia Denali Owner Manual - 2013 - crc2 - 12/11/12

Black plate (13,1)

Keys, Doors, and Windows

2-13

Immobilizer See Radio Frequency Statement on page 13‑20 for information regarding Part 15 of the Federal Communications Commission (FCC) rules and Industry Canada Standards RSS-GEN/210/220/310.

Immobilizer Operation This vehicle has PASS-Key® III+ (Personalized Automotive Security System) theft-deterrent system. PASS-Key III+ is a passive theft-deterrent system. The system is automatically armed when the key is removed from the ignition. The system is automatically disarmed when the key is turned to ON/RUN, ACC/ACCESSORY, or START from the LOCK/OFF position. You do not have to manually arm or disarm the system.

The security light comes on if there is a problem with arming or disarming the theft-deterrent system. When the PASS-Key III+ system senses an incorrect key, the vehicle does not start. Anyone using a trial-and-error method to start the vehicle will be discouraged because of the high number of electrical key codes. If the engine does not start and the security light on the instrument panel comes on when trying to start the vehicle, there may be a problem with the theft-deterrent system. Turn the ignition off and try again. If the engine still does not start, and the key appears to be undamaged, try another ignition key and check the fuses. See Fuses and Circuit Breakers on page 10‑28 for additional information. If the engine still does not start with the other key, the vehicle needs service. If the vehicle does start, the first key may be faulty. See your dealer who can

service the PASS-Key III+ to have a new key made. In an emergency, contact Roadside Assistance. See Roadside Assistance Program (Mexico) on page 13‑7 or Roadside Assistance Program (U.S. and Canada) on page 13‑10. It is possible for the PASS-Key III+ decoder to learn the transponder value of a new or replacement key. Up to 10 keys may be programmed to the vehicle. The following procedure is for programming additional keys only. If all currently programmed keys are lost or do not operate, you must see your dealer or a locksmith who can service PASS-Key III+ to have keys made and programmed to the system. See your dealer or a locksmith who can service PASS-Key III+ to get a new key blank that is cut exactly as the ignition key that operates the system.

Acadia/Acadia Denali Owner Manual - 2013 - crc2 - 12/11/12

Black plate (14,1)

2-14

Keys, Doors, and Windows

To program the new additional key:

1. Verify that the new key has a 1

2.

stamped on it. Insert the already programmed key in the ignition and start the engine. If the engine does not start, see your dealer for service. 3. After the engine has started, turn

4.

the key to LOCK/OFF, and remove the key. Insert the key to be programmed and turn it to the ON/RUN position within five seconds of the original key being turned to the LOCK/OFF position. The security light turns off once the key has been programmed.

5. Repeat Steps 1–4 if additional

keys are to be programmed.

If the PASS-Key III+ key is lost or damaged, see your dealer or a locksmith to have a new key made. The SERVICE THEFT DETERRENT SYSTEM message displays on the Driver Information Center (DIC) when there is a problem with the theft-deterrent system. See Security Messages on page 5‑38 for additional information. Do not leave the key or device that disarms or deactivates the theft-deterrent system in the vehicle.

Exterior Mirrors

Convex Mirrors

{ WARNING

A convex mirror can make things, like other vehicles, look farther away than they really are. If you cut too sharply into the right lane, you could hit a vehicle on the right. Check the inside mirror or glance over your shoulder before changing lanes.

The passenger side mirror is convex shaped. A convex mirror's surface is curved so more can be seen from the driver seat.

Acadia/Acadia Denali Owner Manual - 2013 - crc2 - 12/11/12

Black plate (15,1)

Power Mirrors

Keys, Doors, and Windows

2-15

Folding Mirrors For vehicles with manual folding mirrors, push the mirror toward the vehicle. Pull the mirror out to return to its original position. For vehicles with power folding mirrors:

Base Model

To adjust the mirrors: 1. Press o or p to select a mirror. 2. Press the control pad to adjust

the mirror.

3. Return the switch to the center

to deselect the mirror.

Uplevel Model

To adjust the mirrors: 1. Press (1) or (2) to select a

mirror.

2. Press the control pad to adjust

the mirror.

3. Press (1) or (2) again to deselect

the mirror.

Side Blind Zone Alert (SBZA) If the vehicle has the SBZA system, see Side Blind Zone Alert (SBZA) on page 9‑33.

1. Press (1) to fold the mirrors out

to the driving position.

2. Press (2) to fold the mirrors in to

the folded position.

Acadia/Acadia Denali Owner Manual - 2013 - crc2 - 12/11/12

Black plate (16,1)

2-16

Keys, Doors, and Windows

Automatic Dimming Mirror If the vehicle has the automatic dimming mirror, the driver outside mirror automatically adjusts for the glare of the headlamps from behind. This feature is controlled by the on and off setting on the inside rearview mirror. See Automatic Dimming Rearview Mirror on page 2‑18.

Blind Spot Mirrors The blind spot mirror is a small convex mirror built into the upper and outer corner of both outside mirrors. It can show objects that may be in the vehicle's blind zone.

Resetting the Power Folding Mirrors Reset the power folding mirrors if:

The mirrors are accidentally obstructed while folding. They are accidentally manually folded/unfolded. The mirrors vibrate at normal driving speeds.

To reset the mirrors, fold and unfold the mirrors one time using the power folding mirror controls. A popping noise may be heard during the resetting. This sound is normal during the reset operation.

Heated Mirrors For vehicles with heated mirrors: 1 (Rear Window Defogger): Press to heat the mirrors. See “Rear Window Defogger” under Dual Automatic Climate Control System on page 8‑4.

Driving with the Blind Spot Mirror

Actual Mirror View

Acadia/Acadia Denali Owner Manual - 2013 - crc2 - 12/11/12

Black plate (17,1)

Keys, Doors, and Windows

2-17

1. When the approaching vehicle is a long distance away, the image in the main mirror is small and near the inboard edge of the mirror.

2. As the vehicle gets closer, the image in the main mirror gets larger and moves outboard.

3. As the vehicle enters the blind

zone, the image transitions from the main mirror to the blind spot mirror.

4. When the vehicle is in the blind zone, the image only appears in the blind spot mirror.

Using the Outside Mirror with the Blind Spot Mirror 1. Set the main mirror so that the side of the vehicle can just be seen and the blind spot mirror has an unobstructed view.

2. When checking for traffic or

before changing a lane, look at the main driver/passenger side mirror to observe traffic in the adjacent lane, behind your

vehicle. Check the blind spot mirror for a vehicle in the blind zone. Then, glance over your shoulder to double check before moving slowly into the adjacent lane.

Park Tilt Mirrors If the vehicle has the memory package, the outside mirrors have a park tilt feature. This feature tilts the outside mirrors to a preselected position when the vehicle is in R (Reverse). This allows the driver to view the curb for parallel parking. The passenger and/or driver mirror returns to its original position when the vehicle is shifted out of R (Reverse), or the ignition is turned off or to OFF/LOCK. This feature can be turned on or off through the Driver Information Center (DIC). See Vehicle Personalization on page 5‑41 for more information.

Interior Mirrors

Manual Rearview Mirror Adjust the mirror to view the area behind the vehicle. For vehicles with a manual rearview mirror, push the tab forward for daytime use and pull it for nighttime use to avoid glare from the headlamps from behind. For vehicles with OnStar, center the twist knob for daytime use and turn it to the side for nighttime use. Vehicles with OnStar have three control buttons at the bottom of the mirror. See your dealer for more information about OnStar and how to subscribe to it. See OnStar Overview on page 14‑1.

Acadia/Acadia Denali Owner Manual - 2013 - crc2 - 12/11/12

Black plate (18,1)

2-18

Keys, Doors, and Windows

Windows

{ WARNING

Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke.

Automatic Dimming Rearview Mirror The vehicle may have an automatic dimming inside rearview mirror. The mirror automatically reduces the glare from the headlamps from behind. The dimming feature and the indicator light come on when the vehicle is started. There may be an on and off setting on the mirror. O (On/Off): Press to turn the dimming feature on or off. Cleaning the Mirror Do not spray glass cleaner directly on the mirror. Use a soft towel dampened with water.

The vehicle aerodynamics are designed to improve fuel economy performance. This may result in a pulsing sound when either rear window is down and the front windows are up. To reduce the sound, open either a front window or the sunroof, if equipped.

Power Windows

{ WARNING Children could be seriously injured or killed if caught in the path of a closing window. Never leave keys in a vehicle with children. When there are children in the rear seat, use the window lockout button to prevent operation of the windows. See Keys on page 2‑1.

Acadia/Acadia Denali Owner Manual - 2013 - crc2 - 12/11/12

Black plate (19,1)

Keys, Doors, and Windows

2-19

Express-Up/Express-Down Windows A window with the express-up/down feature allows it to be raised or lowered without holding the switch. Press or pull the window switch fully and release it to activate the express feature. The express mode can be canceled by pressing or pulling the switch. Programming the Power Windows If the battery on the vehicle has been recharged, disconnected, or replaced, windows with the express-up feature need to be reprogrammed for this feature to work. To program the window: 1. Close all doors with the ignition in the ACC/ACCESSORY, ON/ RUN position, or when Retained Accessory Power (RAP) is active. See Retained Accessory Power (RAP) on page 9‑18.

2. Press and continue to hold the window switch until the window is fully open.

3. Pull up and hold the window switch to close the window. Continue to hold it briefly after the window is fully closed.

4. Repeat for each window that has

the express-up feature.

Anti-Pinch Feature The anti-pinch feature is on windows with the express-up feature. If an object is in the way of the window as it is express-closing, or in certain weather conditions like severe icing, the window will stop and open to a factory preset position. The window functions normally once the obstruction is removed.

Uplevel Shown, Base Similar The driver door also has switches that control the passenger and rear windows. The power windows work with the ignition in ACC/ ACCESSORY, ON/RUN or when Retained Accessory Power (RAP) is active. See Retained Accessory Power (RAP) on page 9‑18. Press the switch to lower the window. Pull up on the front edge of the switch to raise the window.

Acadia/Acadia Denali Owner Manual - 2013 - crc2 - 12/11/12

Black plate (20,1)

2-20

Keys, Doors, and Windows

Sun Visors Pull the sun visor down or unhook it and move it to the side to reduce glare. Visor Vanity Mirror Lift the cover to use the mirror and turn the lamps on.

Roof

Sunroof The ignition must be in ON/RUN, ACC/ACCESSORY, or Retained Accessory Power (RAP) must be active to operate the sunroof and power sunshade. See Retained Accessory Power (RAP) on page 9‑18. The vehicle may have a sunroof over the front seats and a rear sunroof over the second row seats. The rear sunroof does not open.

Rear Window Lockout

The rear window lockout feature prevents the rear passenger windows from operating, except from the driver position. Press v to activate the rear window lockout switch. The indicator light comes on when activated. Press v again to deactivate the lockout switch.

Acadia/Acadia Denali Owner Manual - 2013 - crc2 - 12/11/12

Black plate (21,1)

Keys, Doors, and Windows

2-21

Express-open/Express-close: From the closed position, press and release the rear of the switch to express-open the sunroof. Press and release the front of the switch to express-close the sunroof. Manual Sunshade The sunshades must be opened and closed manually. To open the sunshade, press the button on the sunshade handle to release it and guide it back. To close the sunshade, pull the sunshade forward until it latches.

Dirt and debris may collect on the sunroof seal or in the track. This could cause an issue with sunroof operation or noise. It could also plug the water drainage system. Periodically open the sunroof and remove any obstacles or loose debris. Wipe the sunroof seal and roof sealing area using a clean cloth, mild soap, and water. Do not remove grease from the sunroof.

Vent: From the closed position, press and hold the front of the switch to vent the sunroof. Press and hold the rear of the switch to close the sunroof.

Acadia/Acadia Denali Owner Manual - 2013 - crc2 - 12/11/12

Black plate (22,1)

2-22

Keys, Doors, and Windows

2 NOTES

Acadia/Acadia Denali Owner Manual - 2013 - crc2 - 12/11/12

Black plate (1,1)

Seats and Restraints

3-1

Seats and Restraints

Head Restraints

Head Restraints . . . . . . . . . . . . . . . 3-2

Front Seats

Seat Adjustment . . . . . . . . . . . . . . 3-3
Power Seat Adjustment . . . . . . . 3-4
Lumbar Adjustment . . . . . . . . . . . 3-4
Reclining Seatbacks . . . . . . . . . . 3-5
Memory Seats . . . . . . . . . . . . . . . . 3-6
Heated and Ventilated Front

Seats . . . . . . . . . . . . . . . . . . . . . . . . 3-8

Rear Seats

Rear Seats . . . . . . . . . . . . . . . . . . . . 3-9
Third Row Seats . . . . . . . . . . . . . 3-11

Safety Belts

Safety Belts . . . . . . . . . . . . . . . . . . 3-14
How to Wear Safety Belts

Properly . . . . . . . . . . . . . . . . . . . . 3-15

Lap-Shoulder Belt . . . . . . . . . . . 3-16
Safety Belt Use During

Pregnancy . . . . . . . . . . . . . . . . . . 3-21
Safety Belt Extender . . . . . . . . . 3-22
Safety System Check . . . . . . . . 3-22
Safety Belt Care . . . . . . . . . . . . . 3-22
Replacing Safety Belt System

Parts after a Crash . . . . . . . . . 3-22

Airbag System

Airbag System . . . . . . . . . . . . . . . 3-23
Where Are the Airbags? . . . . . 3-25
When Should an Airbag

Inflate? . . . . . . . . . . . . . . . . . . . . . 3-27

What Makes an Airbag

Adding Equipment to the

Airbag-Equipped Vehicle . . . 3-35
Airbag System Check . . . . . . . . 3-36
Replacing Airbag System

Parts after a Crash . . . . . . . . . 3-36

Child Restraints

Older Children . . . . . . . . . . . . . . . 3-37
Infants and Young

Children . . . . . . . . . . . . . . . . . . . . 3-39
Child Restraint Systems . . . . . 3-41
Where to Put the Restraint . . . 3-43
Lower Anchors and Tethers

for Children (LATCH System) . . . . . . . . . . . . . . . . . . . . 3-44

Inflate? . . . . . . . . . . . . . . . . . . . . . 3-28

Replacing LATCH System

How Does an Airbag

Parts After a Crash . . . . . . . . . 3-51

Restrain? . . . . . . . . . . . . . . . . . . . 3-28

Securing Child Restraints

What Will You See after an

(Rear Seat) . . . . . . . . . . . . . . . . . 3-51

Airbag Inflates? . . . . . . . . . . . . 3-29

Securing Child Restraints

(Front Passenger Seat) . . . . 3-53

Passenger Sensing

System . . . . . . . . . . . . . . . . . . . . . 3-30

Servicing the Airbag-Equipped

Vehicle . . . . . . . . . . . . . . . . . . . . . 3-34

Acadia/Acadia Denali Owner Manual - 2013 - crc2 - 12/11/12

Black plate (2,1)

3-2

Seats and Restraints

Head Restraints

Front Seats

{ WARNING

With head restraints that are not installed and adjusted properly, there is a greater chance that occupants will suffer a neck/ spinal injury in a crash. Do not drive until the head restraints for all occupants are installed and adjusted properly.

The vehicle's front seats have adjustable head restraints in the outboard seating positions.

Adjust the head restraint so that the top of the restraint is at the same height as the top of the occupant's head. This position reduces the chance of a neck injury in a crash.

To raise or lower the head restraint, press the button located on the side of the head restraint, and pull up or push the head restraint down, and release the button. Pull and push on the head restraint after the button is released to make sure that it is locked in place. To adjust the head restraint forward, grasp the head restraint and pull forward until the desired locking position is reached. To adjust the head restraint rearward, press the button located on the side of the head restraint,

Acadia/Acadia Denali Owner Manual - 2013 - crc2 - 12/11/12

Black plate (3,1)

Front Seats

Seat Adjustment

{ WARNING You can lose control of the vehicle if you try to adjust a driver seat while the vehicle is moving. Adjust the driver seat only when the vehicle is not moving.

and push the head restraint rearward until the desired locking position is reached. Try to move the head restraint after the button is released to make sure that it is locked in place. The front seat outboard head restraints are not designed to be removed. Rear Seats The vehicle's second-row seats have head restraints in the outboard seating positions that cannot be adjusted. The vehicle's third-row seats have headrests in the outboard seating positions that cannot be adjusted. The second-row head restraints and third-row headrests are not designed to be removed.

1. Seat Adjustment Handle

Seats and Restraints

3-3

2. Driver Seat Height Adjustment

Lever

3. Seatback Lever To adjust a manual seat: 1. Lift the handle (1) under the seat

to unlock it.

2. Slide the seat to the desired

position, and then release the handle (1).

3. Try to move the seat back and

forth to be sure it is locked in place.

Move the lever (2) up or down to raise or lower the seat. Use the lever (3) to adjust the seatback. See Reclining Seatbacks on page 3‑5.

Acadia/Acadia Denali Owner Manual - 2013 - crc2 - 12/11/12

Black plate (4,1)

3-4

Seats and Restraints

Power Seat Adjustment

1. Seat Adjustment Control 2. Seatback Control 3. Lumbar Control To adjust a power seat, if equipped: . Move the seat forward or

rearward by sliding the control (1) forward or rearward. . Raise or lower the front part of the seat cushion by moving the front of the control (1) up or down.

Lumbar Adjustment

Manual Lumbar

. Raise or lower the entire seat by moving the rear of the control (1) up or down.

. Adjust the seatback by tilting the

top of the control (2) forward or rearward. See Reclining Seatbacks on page 3‑5. Increase or decrease lumbar support by pressing the front or rear of the control (3). See Lumbar Adjustment on page 3‑4.

If available, move the handle forward or rearward to increase or decrease lumbar support.

Acadia/Acadia Denali Owner Manual - 2013 - crc2 - 12/11/12

Black plate (5,1)

Seats and Restraints

3-5

Power Lumbar

If available, press and hold the front or rear of control to increase or decrease lumbar support. Release the control when the seatback reaches the desired level of lumbar support.

Reclining Seatbacks { WARNING

Sitting in a reclined position when the vehicle is in motion can be dangerous. Even when buckled up, the safety belts cannot do their job. The shoulder belt will not be against your body. Instead, it will be in front of you. In a crash, you could go into it, receiving neck or other injuries. The lap belt could go up over your abdomen. The belt forces would be there, not at your pelvic bones. This could cause serious internal injuries. For proper protection when the vehicle is in motion, have the seatback upright. Then sit well back in the seat and wear the safety belt properly.

Do not have a seatback reclined if the vehicle is moving. Manual Reclining Seatbacks

{ WARNING

If either seatback is not locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always push and pull on the seatbacks to be sure they are locked.

Acadia/Acadia Denali Owner Manual - 2013 - crc2 - 12/11/12

Black plate (6,1)

3-6

Seats and Restraints

2. Push and pull on the seatback to

make sure it is locked.

Power Reclining Seatbacks

Memory Seats

To recline the seatback: 1. Lift the lever. 2. Move the seatback to the desired position, and then release the lever to lock the seatback in place.

3. Push and pull on the seatback to

make sure it is locked.

To return the seatback to the upright position: 1. Lift the lever fully without applying pressure to the seatback, and the seatback will return to the upright position.

If available, the controls on the driver door are used to program and recall memory settings for the driver seat, outside mirrors, and power steering column (if equipped).

To adjust a power seatback, if equipped:

Tilt the top of the control rearward to recline. Tilt the top of the control forward to raise.

Acadia/Acadia Denali Owner Manual - 2013 - crc2 - 12/11/12

Black plate (7,1)

Storing Memory Positions To save into memory: 1. Adjust the driver seat and

seatback recliner, both outside mirrors, and the power steering column (if equipped). Not all vehicles will have the ability to save and recall the mirror positions.

2. Press and hold “1” until

two beeps sound.

3. Repeat for a second driver

position using “2.”

To recall, press and release “1” or “2.” The vehicle must be in P (Park). A single beep will sound. The seat, outside mirrors, and power steering column (if equipped) will move to the positions previously stored for the identified driver.

Memory Remote Recall The memory feature can recall the driver seat, outside mirrors, and power steering column (if equipped) to stored positions when entering the vehicle. To activate, unlock the driver door with the Remote Keyless Entry (RKE) transmitter. The driver seat, outside mirrors, and power steering column (if equipped) will move to the memory positions associated with the transmitter used to unlock the vehicle. This feature is turned on or off using the vehicle personalization menu. See Vehicle Personalization on page 5‑41. To stop recall movement, press one of the power seat controls, memory buttons, power mirror buttons, or the power steering column control (if equipped). If something has blocked the driver seat and/or steering column while recalling a memory position, the

Seats and Restraints

3-7

recall may stop. Remove the obstruction; then press and hold the appropriate manual control for the memory item that is not recalling for two seconds. Try recalling the memory position again by pressing the appropriate memory button. If the memory position is still not recalling, see your dealer for service.

Easy Exit Driver Seat The easy exit feature can move the driver seat rearward and the power steering column (if equipped) up and forward to allow extra room to exit the vehicle. S (Easy Exit Positions): Press to activate the recall. The vehicle must be in P (Park). If this feature is programmed on in the vehicle personalization menu, automatic driver seat and power steering column movement occur when the ignition key is removed.

Acadia/Acadia Denali Owner Manual - 2013 - crc2 - 12/11/12

Black plate (8,1)

3-8

Seats and Restraints

A single beep sounds. The driver seat moves back approximately 8 cm (3 in) and the power steering column (if equipped) moves up and forward. To move the seat back farther, press S again until the seat is all the way back. If something has blocked the driver seat while recalling the exit position, the recall may stop. Remove the obstruction; then press and hold the power seat control rearward for two seconds. Try recalling the exit position again. If the exit position is still not recalling, see your dealer for service. See Vehicle Personalization on page 5‑41.

Heated and Ventilated Front Seats

{ WARNING

If you cannot feel temperature change or pain to the skin, the seat heater may cause burns. To reduce the risk of burns, people with such a condition should use care when using the seat heater, especially for long periods of time. Do not place anything on the seat that insulates against heat, such as a blanket, cushion, cover, or similar item. This may cause the seat heater to overheat. An overheated seat heater may cause a burn or may damage the seat.

Heated and Cooled Seat Buttons

Shown, Heated Seat Buttons

Similar

If available,

If available, the buttons are on the center console. To operate, the engine must be running. I (Heated Seatback): press to heat the seatback only. H (Cooled Seat): If available, press to cool the entire seat. J (Heated Seat and Seatback): Press to heat the seat and seatback. Press the button once for the highest setting. With each press of the button, the seat will change to the next lower setting, and then to

Acadia/Acadia Denali Owner Manual - 2013 - crc2 - 12/11/12

Black plate (9,1)

Rear Seats

1. Seat Adjustment Handle 2. Reclining Seatback Strap 3. Sliding Seat Lever

the off setting. The lights indicate three for the highest setting and one for the lowest. The passenger heated seat may take longer to heat up. The heated and/or cooled seats are canceled after the ignition is turned off.

Remote Start Heated Seats When it is cold outside, the heated seats may turn on automatically during a remote vehicle start. The heated seats will be canceled when the ignition is turned on. Press the desired heated seat button to use the heated seats after the vehicle is started. The heated seat button lights will not turn on during a remote start. The temperature of an unoccupied seat may be reduced. See Remote Vehicle Start on page 2‑4.

Seats and Restraints

3-9

Entering and Exiting the Third Row

{ WARNING Using the third row seating position while the second row is folded, or folded and tumbled, could cause injury in a sudden stop or crash. Be sure to return the seat to the passenger seating position. Push and pull on the seat to make sure it is locked into place.

Notice: Folding a rear seat with the safety belts still fastened may cause damage to the seat or the safety belts. Always unbuckle the safety belts and return them to their normal stowed position before folding a rear seat.

Acadia/Acadia Denali Owner Manual - 2013 - crc2 - 12/11/12

Black plate (10,1)

3-10

Seats and Restraints

5. Pull the sliding seat lever (3) forward. The seatback will tilt forward, and the seat will begin sliding forward. Continue to push forward on the seatback until the entire seat moves all the way forward and the seat cushion is folded.

Returning the Seat to the Seating Position To return the second row seat to its normal seating position: 1. Remove objects on the floor

behind the second row seat or in the seat tracks on the floor. 2. Slide the seat rearward by

pushing on the seatback until the seat is locked into place.

3. Continue pushing the seatback

rearward until the seatback is locked into place.

4. Push down on the rear of the

seat cushion until it is locked in place.

5. Push and pull on the seatback and seat cushion to make sure they are locked in place.

6. Check that the safety belt is not

under the seat cushion. Reclining the Seatbacks To recline the seatback: 1. Leaning rearward in the seat,

pull the reclining seatback strap (2).

2. Move the seatback to the desired position, and then release the strap (2) to lock the seatback in place.

3. Push and pull on the seatback to

make sure it is locked. Folding the Seatback To fold the second row seatbacks: 1. Remove anything on or under

the seat.

2. Place the armrest in the upright

position, and unfasten the safety belt.

To access the third row: 1. Remove objects on the floor in

front of or on the second row seat, or in the seat tracks on the floor.

2. Move the front center console

armrest completely forward. See Center Console Storage on page 4‑2.

3. Place the folding armrests in the

upright position.

4. Make sure that the safety belt is

unfastened and in the stowed position.

Acadia/Acadia Denali Owner Manual - 2013 - crc2 - 12/11/12

Black plate (11,1)

Seats and Restraints

3-11

3. Pull forward on the reclining

seatback strap (2). The head restraint will fold down automatically.

To return the seatback to the seating position, lift the seatback and push it rearward until it locks into place. Push and pull on the seatback to make sure it is locked. Pull up on the head restraint to return it to the upright, locked position. Adjusting the Seats To adjust the second row seats, pull outward on the seat adjustment handle (1). Slide the seat forward or rearward to the desired position. Release the handle (1), and push and pull on the seat to make sure it is locked.

Third Row Seats

{ WARNING Using the third row seating position while the second row is folded, or pushed forward in the entry position, could cause injury in a sudden stop or crash. Be sure to return the seat to the passenger seating position. Push and pull on the seat to make sure it is locked into place.

Folding the Seatback Notice: Folding a rear seat with the safety belts still fastened may cause damage to the seat or the safety belts. Always unbuckle the safety belts and return them to their normal stowed position before folding a rear seat. To fold the third row seatback: 1. Remove anything on or under

the seat.

2. Disconnect the rear safety belt

mini-latch, using a key in the slot on the mini-buckle, and let the belt retract into the headliner. Stow the mini-latch in the holder in the headliner.

Acadia/Acadia Denali Owner Manual - 2013 - crc2 - 12/11/12

Black plate (12,1)

3-12

Seats and Restraints

Returning the Seat to the Seating Position To return the seatback to the seating position: 1. From the rear of the vehicle,

raise the seatback to the upright position using the pullstrap on the back of the third row seat, or lift the seatback and push it into place from inside the vehicle.

2. The headrest must be locked

into place before sitting in the seat.

{ WARNING

If either seatback is not locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always push and pull on the seatbacks to be sure they are locked.

3. Push and pull on the seatback to

make sure it is locked in place.

{ WARNING

A safety belt that is improperly routed, not properly attached, or twisted will not provide the protection needed in a crash. The person wearing the belt could be seriously injured. After raising the rear seatback, always check to be sure that the safety belts are properly routed and attached, and are not twisted.

4. Reconnect the center safety belt mini-latch to the mini-buckle. Do not let it twist.

5. Pull on the safety belt to be sure

the mini-latch is secure.

3. Pull up on the release lever on

the back of the seat. The headrest moves forward automatically.

4. Push the seatback forward to

lay flat.

Acadia/Acadia Denali Owner Manual - 2013 - crc2 - 12/11/12

Black plate (13,1)

Removing the Third Row Seats To remove a third row seat: 1. Remove the cargo management

system, if available and installed. See Cargo Management System on page 4‑3.

2. Remove anything on or under

the seat.

Notice: Folding a rear seat with the safety belts still fastened may cause damage to the seat or the safety belts. Always unbuckle the safety belts and return them to their normal stowed position before folding a rear seat. 3. Fold the seatback down. See

“Folding the Seatback” earlier in this section.

4. Remove the rear bolts on the floor on each side of the seat.

5. Remove the seat by tilting it

slightly upward, and then pulling it out of the rear of the vehicle in one motion.

Seats and Restraints

3-13

6. Replace the bolts in the floor

4. Raise the seatback to its upright

position. Push and pull on the seatback to make sure it is locked into place.

5. Push the headrest up into

position. Push and pull on the headrest to make sure it is locked into place.

6. Reconnect the center safety belt mini-latch to the mini-buckle. Do not let it twist.

holes for storage.

Installing the Third Row Seats To reinstall a third row seat: 1. Before installing the seat the

seatback must be folded forward. See “Folding the Seatback” earlier in this section. The seats must be placed in the proper locations to attach correctly. The wider seat must be installed on the driver side and the narrower seat on the passenger side. Remove the bolts from the holes in the floor before installing the seats.

2. Place the seat on the vehicle

floor so that the front seat hooks are on the vehicle bars.

3. Reinstall the bolts, and torque to

55 Y (41 lb ft). Pull up on the seat to make sure it is locked in place.

Acadia/Acadia Denali Owner Manual - 2013 - crc2 - 12/11/12

Black plate (14,1)

3-14

Seats and Restraints

Safety Belts This section of the manual describes how to use safety belts properly. It also describes some things not to do with safety belts.

{ WARNING

Do not let anyone ride where a safety belt cannot be worn properly. In a crash, if you or your passenger(s) are not wearing safety belts, injuries can be much worse than if you are wearing safety belts. You can be seriously injured or killed by hitting things inside the vehicle harder or by being ejected from the vehicle. In addition, anyone who is not buckled up can strike other passengers in the vehicle. It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, passengers riding in these areas

(Continued)

WARNING (Continued)

are more likely to be seriously injured or killed. Do not allow passengers to ride in any area of the vehicle that is not equipped with seats and safety belts. Always wear a safety belt, and check that all passenger(s) are restrained properly too.

This vehicle has indicators as a reminder to buckle the safety belts. See Safety Belt Reminders on page 5‑13.

Why Safety Belts Work

When riding in a vehicle, you travel as fast as the vehicle does. If the vehicle stops suddenly, you keep going until something stops you. It could be the windshield, the instrument panel, or the safety belts! When you wear a safety belt, you and the vehicle slow down together. There is more time to stop because you stop over a longer distance and, when worn properly, your strongest bones take the forces from the

Acadia/Acadia Denali Owner Manual - 2013 - crc2 - 12/11/12

Black plate (15,1)

Seats and Restraints

3-15

safety belts. That is why wearing safety belts makes such good sense. Questions and Answers About Safety Belts Q: Will I be trapped in the vehicle after a crash if I am wearing a safety belt?

A: You could be — whether you are

wearing a safety belt or not. Your chance of being conscious during and after a crash, so you can unbuckle and get out, is much greater if you are belted.

Q: If my vehicle has airbags, why

should I have to wear safety belts?

A: Airbags are supplemental

systems only; so they work with safety belts — not instead of them. Whether or not an airbag is provided, all occupants still have to buckle up to get the most protection.

Also, in nearly all states and in all Canadian provinces, the law requires wearing safety belts.

How to Wear Safety Belts Properly This section is only for people of adult size. There are special things to know about safety belts and children. And there are different rules for smaller children and infants. If a child will be riding in the vehicle, see Older Children on page 3‑37 or Infants and Young Children on page 3‑39. Follow those rules for everyone's protection. It is very important for all occupants to buckle up. Statistics show that unbelted people are hurt more often in crashes than those who are wearing safety belts. There are important things to know about wearing a safety belt properly.

. Sit up straight and always keep

your feet on the floor in front of you.

. Always use the correct buckle

for your seating position.

. Wear the lap part of the belt low

and snug on the hips, just touching the thighs. In a crash, this applies force to the strong pelvic bones and you would be less likely to slide under the lap belt. If you slid under it, the belt would apply force on your abdomen. This could cause serious or even fatal injuries.

Acadia/Acadia Denali Owner Manual - 2013 - crc2 - 12/11/12

Black plate (16,1)

3-16

Seats and Restraints

. Wear the shoulder belt over the shoulder and across the chest. These parts of the body are best able to take belt restraining forces. The shoulder belt locks if there is a sudden stop or crash.

{ WARNING

You can be seriously injured, or even killed, by not wearing your safety belt properly. . Never allow the lap or

shoulder belt to become loose or twisted.

. Never wear the shoulder belt

under both arms or behind your back.

. Never route the lap or shoulder belt over an armrest.

Lap-Shoulder Belt All seating positions in the vehicle have a lap-shoulder belt. If you are using a rear seating position with a detachable safety belt and the safety belt is not attached, see “Returning the Seat to the Seating Position” under Third Row Seats on page 3‑11 for instruction on reconnecting the safety belt to the mini-buckle. The following instructions explain how to wear a lap-shoulder belt properly. 1. Adjust the seat, if the seat is adjustable, so you can sit up straight. To see how, see “Seats”