You may also be interested in...

2009 Ford FLEX Owners Manual

Download PDF Manual

and fog when the rear window defrost is activated. Do not remove ice from the mirrors with a scraper or attempt to readjust the mirror glass if it is frozen in place. These actions could cause damage to the glass and mirrors. Do not clean the housing or glass of any mirror with harsh abrasives, fuel or other petroleum-based cleaning products.


POWER ADJUSTABLE FOOT PEDALS (IF EQUIPPED) The accelerator and brake pedal should only be adjusted when the vehicle is stopped and the gearshift lever is in the P (Park) position. Press and hold the rocker control to adjust accelerator and brake pedal. • Press the back of the control to adjust the pedals toward you. • Press the front of the control to adjust the pedals away from you. WARNING: Never adjust the accelerator and brake pedal with feet on the pedals while the vehicle is moving.


106


2009 Flex (471) Owners Guide, 2nd Printing USA (fus)


Driver Controls


Memory feature (if equipped) The accelerator and brake pedal positions are saved when doing a memory set function and can be recalled along with the vehicle personality features when a memory position is selected through the remote entry transmitter, keyless entry keypad or memory switch on the driver’s door (if equipped with memory feature). Refer to Memory seat/power mirrors/adjustable pedals in the Seating and Safety Restraints chapter. SPEED CONTROL With speed control set, you can maintain a set speed without keeping your foot on the accelerator pedal.


WARNING: Do not use the speed control in heavy traffic or on roads that are winding, slippery or unpaved.


Setting speed control The controls for using your speed control are located on the steering wheel for your convenience. 1. Press the ON control and release it. 2. Accelerate to the desired speed.


3. Press the SET + or SET - control and release it. 4. Take your foot off the accelerator pedal. 5. The indicator instrument cluster will turn on.


light on the


Note: • Vehicle speed may vary momentarily when driving up and down a


steep hill.


107


2009 Flex (471) Owners Guide, 2nd Printing USA (fus)


Driver Controls • If the vehicle speed increases above the set speed on a downhill, you • If the vehicle speed decreases more than 10 mph (16 km/h) below


may want to apply the brakes to reduce the speed.


your set speed on an uphill, your speed control will disengage.


Disengaging speed control To disengage the speed control: • Depress the brake pedal. Disengaging the speed control will not erase previous set speed. Resuming a set speed Press the RESUME control and release it. This will automatically return the vehicle to the previously set speed.


Increasing speed while using speed control There are two ways to set a higher speed: • Press and hold the SET + control until you get to the desired speed, then release the control. You can also use the SET + control to operate the Tap-Up function. Press and release this control to increase the vehicle set speed in small amounts by 1 mph (1.6 km/h).


• Use the accelerator pedal to get to the desired speed. When the vehicle reaches that speed press and release the SET + control.


108


2009 Flex (471) Owners Guide, 2nd Printing USA (fus)


Driver Controls


Reducing speed while using speed control There are two ways to reduce a set speed: • Press and hold the SET - control until you get to the desired speed, then release the control. You can also use the SET - control to operate the Tap-Down function. Press and release this control to decrease the vehicle set speed in small amounts by 1 mph (1.6 km/h).


• Depress the brake pedal until the desired vehicle speed is reached and


press the SET + control.


Turning off speed control There are two ways to turn off the speed control: • Depress the brake pedal. This will


not erase your vehicle’s previously set speed.


• Press the speed control OFF


control.


Note: When you turn off the speed control or the ignition, your speed control set speed memory is erased.


109


2009 Flex (471) Owners Guide, 2nd Printing USA (fus)


Driver Controls


STEERING WHEEL CONTROLS (IF EQUIPPED)


Radio control features Press MEDIA to select: • AM, FM1, FM2, or CD • DVD/FES (if equipped) • SAT1, SAT2 or SAT3 (Satellite • LINE IN (Auxiliary input jack)


Radio mode if equipped).


In Radio mode: • Press


to access the


next/previous preset station.


In CD mode: • Press


to listen to the


next track on the disc. In Satellite radio mode (if equipped): • Press In any mode: • Press VOL + or VOL - to adjust


the volume.


to advance through preset channels.


110


2009 Flex (471) Owners Guide, 2nd Printing USA (fus)


Driver Controls


to complete a voice


to exit voice command.


Navigation system hands free control features (if equipped) control briefly Press and hold icon appears on until the voice the navigation display to use the voice command feature. Press command. For further information on the navigation system, refer to the Navigation System supplement. SYNC system hands free control feature (if equipped) Press briefly to use the voice command feature. You will hear a tone and LISTENING will appear in the radio display. Press and hold Press answer a phone call. Press and hold mode. Press OK to confirm your selection. For further information on the SYNC system, refer to the SYNC supplement. Navigation system/SYNC hands free control features (if equipped) Press voice Navigation display to use the voice command feature. Press answer a phone call. Press and hold a call.


control briefly until the icon appears on the


to exit phone mode or end


to end a call or exit phone


to activate phone mode or


to activate phone mode or


to scroll through various menus and selections. Press


111


2009 Flex (471) Owners Guide, 2nd Printing USA (fus)


Driver Controls


For further information on the Navigation system/SYNC system, refer to the Navigation System and SYNC supplements.


MULTI-PANEL VISTA ROOF (IF EQUIPPED) The multi-panel vista roof control is located on the overhead console.


WARNING: Do not let children play with the multi-panel vista roof or leave children unattended in the vehicle. They may


seriously hurt themselves.


The multi-panel vista roof is equipped with an automatic, one-touch, express opening and closing feature. To stop motion at any time during the one-touch operation, press the control a second time. To open the multi-panel vista roof: Press and release the SLIDE control, the roof will open automatically. Press the switch again to stop the roof.


WARNING: When closing the multi-panel vista roof, you should verify that it is free of obstructions and ensure that children


and/or pets are not in the proximity of the roof opening.


To close the multi-panel vista roof: Pull and release the SLIDE control, the roof will close automatically. Press the switch again to stop the roof. Bounce-back: When an obstacle has been detected in the roof opening as the roof is closing, the roof will automatically open and stop at a prescribed position. Bounce-back override: To override bounce-back function, pull and hold the SLIDE switch within two seconds of a bounce-back event. The closing force will begin to increase each time the roof is closed for the first three closing cycles, with bounce-back active. For example: Bounce-back can be used to overcome the resistance of ice on the roof or seals To vent the multi-panel vista moon roof: Press and release the TILT control, the roof will move to the vent position automatically from any roof position. Press the switch again to stop the roof. Pull and hold the TILT control to close the roof.


112


2009 Flex (471) Owners Guide, 2nd Printing USA (fus)


Driver Controls


The multi-panel vista roof has a built-in sliding shade that can be manually opened or closed when the glass panel is shut. To close the shade, pull it toward the front of the vehicle.


HOMELINK姞 WIRELESS CONTROL SYSTEM (IF EQUIPPED) The HomeLink威 Wireless Control System, located on the driver’s visor, provides a convenient way to replace up to three hand-held transmitters with a single built-in device. This feature will learn the radio frequency codes of most transmitters to operate garage doors, entry gate operators, security systems, entry door locks, and home or office lighting.


WARNING: When programming your HomeLink威 Wireless Control System to a garage door or gate, be sure that people and


objects are out of the way to prevent potential injury or damage.


Do not use the HomeLink威 Wireless Control System with any garage door opener that lacks safety stop and reverse features as required by U.S. federal safety standards (this includes any garage door opener model manufactured before April 1, 1982). A garage door which cannot detect an object, signaling the door to stop and reverse, does not meet current U.S. federal safety standards. For more information, contact HomeLink威 at: www.homelink.com or 1–800–355–3515. Retain the original transmitter for use in other vehicles as well as for future programming procedures (i.e. new HomeLink威 equipped vehicle purchase). It is also suggested that upon the sale of the vehicle, the programmed Homelink威 buttons be erased for security purposes, refer to Programming in this section.


Programming Do not program HomeLink威 with the vehicle parked in the garage. Note: Your vehicle may require the ignition switch to be turned to the accessory position for programming and/or operation of the HomeLink威. It is also recommended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLink威 for quicker training and accurate transmission of the radio-frequency signal.


113


2009 Flex (471) Owners Guide, 2nd Printing USA (fus)


Driver Controls


1. Position the end of your hand-held transmitter 1–3 inches (2–8 cm) away from the HomeLink威 button you wish to program (located on your visor) while keeping the indicator light in view. 2. Simultaneously press and hold both the chosen HomeLink威 and hand-held transmitter buttons until the HomeLink威 indicator light changes from a slow to a rapidly blinking light. Now you may release both the HomeLink威 and hand-held transmitter buttons. Note: Some entry gates and garage door openers may require you to replace Step 2 with procedures noted in the Gate Operator and Canadian Programming in this section for Canadian residents. 3. Firmly press and hold for five seconds and release the programmed HomeLink威 button up to two separate times to activate the door. If the door does not activate, press and hold the just-trained HomeLink威 button and observe the indicator light. • If the indicator light stays on constantly, programming is complete and your device should activate when the HomeLink威 button is pressed and released. • If the indicator light blinks rapidly for two seconds and then turns to a constant light continue with “Programming” Steps 4 through 6 to complete programming of a rolling code equipped device (most commonly a garage door opener). 4. At the garage door opener receiver (motor-head unit) in the garage, locate the “learn” or “smart” button (usually near where the hanging antenna wire is attached to the unit). 5. Firmly press and release the “learn” or “smart” button. (The name and color of the button may vary by manufacturer.) Note: There are 30 seconds in which to initiate Step 6. 6. Return to the vehicle and firmly press, hold for two seconds and release the programmed HomeLink威 button. Repeat the press/hold/release sequence again and, depending on the brand of the garage door opener (or other rolling code equipped device), repeat this sequence a third time to complete the programming. HomeLink威 should now activate your rolling code equipped device. To program additional HomeLink威 buttons begin with Step 1 in this section. For questions or comments, please contact HomeLink威 at www.homelink.com or 1–800–355–3515.


114


2009 Flex (471) Owners Guide, 2nd Printing USA (fus)


Driver Controls


Gate Operator & Canadian Programming During programming, your hand-held transmitter may automatically stop transmitting — not allowing enough time for HomeLink威 to accept the signal from the hand-held transmitter. After completing Step 1 outlined in the Programming section, replace Step 2 with the following: Note: If programming a garage door opener or gate operator, it is advised to unplug the device during the “cycling” process to prevent overheating. • Continue to press and hold the HomeLink威 button (note Step 2 in the


Programming section) while you press and release — every two seconds (“cycle”) your hand-held transmitter until the frequency signal has been accepted by the HomeLink威. The indicator light will flash slowly and then rapidly after HomeLink威 accepts the radio frequency signal.


• Proceed with Step 3 in the Programming section.


Operating the HomeLink姞 Wireless Control System To operate, simply press and release the appropriate HomeLink威 button. Activation will now occur for the trained product (garage door, gate operator, security system, entry door lock, or home or office lighting etc.). For convenience, the hand-held transmitter of the device may also be used at any time. In the event that there are still programming difficulties, contact HomeLink威 at www.homelink.com or 1–800–355–3515.


115


2009 Flex (471) Owners Guide, 2nd Printing USA (fus)


Driver Controls


Erasing HomeLink姞 buttons To erase the three programmed buttons (individual buttons cannot be erased): • Press and hold the two outer HomeLink威 buttons until the indicator light begins to flash-after 20 seconds. Release both buttons. Do not hold for longer that 30 seconds.


HomeLink威 is now in the train (or learning) mode and can be programmed at any time beginning with Step 1 in the Programming section. Reprogramming a single HomeLink姞 button To program a device to HomeLink威 using a HomeLink威 button previously trained, follow these steps: 1. Press and hold the desired HomeLink威 button. Do NOT release the button. 2. The indicator light will begin to flash after 20 seconds. Without releasing the HomeLink威 button, follow Step 1 in the Programming section. For questions or comments, contact HomeLink威 at www.homelink.com or 1–800–355–3515.


MESSAGE CENTER With the ignition on, the message center, located on your instrument cluster, displays important vehicle information through a constant monitor of vehicle systems. You may select display features on the message center for a display of status. The system will also notify you of potential vehicle problems with a display of system warnings followed by a long indicator chime.


116


2009 Flex (471) Owners Guide, 2nd Printing USA (fus)


Driver Controls


Selectable features Reset Press this control to select and reset functions shown in the INFO menu and SETUP menu.


Info menu This control displays the following control displays: • Trip Odometer A or B • Distance to Empty • Average Fuel Economy • Instantaneous Fuel Economy • Elapsed Timer • Blank (odometer off) Odometer/Trip odometer Refer to Gauges in the Instrument Cluster chapter. Distance to empty (DTE) Selecting this function from the INFO menu estimates approximately how far you can drive with the fuel remaining in your tank under normal driving conditions. Remember to turn the ignition off when refueling to allow this feature to correctly detect the added fuel. The DTE function will display FUEL LEVEL LOW when you have the following: • 50 miles (80 km) to empty • 25 miles (40 km ) • 10 miles (20 km) DTE is calculated using a running average fuel economy, which is based on your recent driving history of 500 miles (800 km). This value is not the same as the average fuel economy display. The running average fuel economy is reinitialized to a factory default value if the battery is disconnected.


117


2009 Flex (471) Owners Guide, 2nd Printing USA (fus)


Driver Controls


service stations


Average fuel economy (AFE) Select this function from the INFO menu to display your average fuel economy in miles/gallon or liters/100 km. If you calculate your average fuel economy by dividing miles traveled by gallons of fuel used (liters of fuel by used 100 kilometers traveled), your figure may be different than displayed for the following reasons: • your vehicle was not perfectly level during fill-up • differences in the automatic shut-off points on the fuel pumps at • variations in top-off procedure from one fill-up to another • rounding off the displayed values to the nearest 0.1 gallon (liter) 1. Drive the vehicle at least 5 miles (8 km) with the speed control system engaged to display a stabilized average. 2. Record the highway fuel economy for future reference. It is important to press the RESET control after setting the speed control to get accurate highway fuel economy readings. Instantaneous fuel economy Select this function from the INFO menu to display your instantaneous fuel economy. This will display your fuel economy as a bar graph ranging from excellent economy. Your vehicle must be moving to calculate instantaneous fuel economy. When your vehicle is not moving, this function shows illuminated. Instantaneous fuel economy cannot be reset. Elapsed timer Select this function from the INFO menu to display a timer. To operate the elapsed timer perform the following: 1. Press and release RESET to start or stop the timer. 2. Press and hold RESET for two seconds to reset the timer.


poor economy to


, one or no bars


118


2009 Flex (471) Owners Guide, 2nd Printing USA (fus)


Driver Controls


language)


Blank display Select this function from the INFO menu to turn display off. Setup menu Press this control for the following displays: • Reset to English (if in another • System Check • Oil Life • Units (English/Metric) • Autolamp Delay • Autolock • Autounlock • Easy entry/exit seat (if equipped) • Reverse sensing system (Rear Park Aid) • Power Liftgate (if equipped) • Language Reset to English (if in another language) When entering the SETUP menu and a non-English language has been selected, this will be displayed. Press the RESET control to change back to English. System check Selecting this function from the SETUP menu causes the message center to cycle through each of the systems being monitored. For each of the monitored systems, the message center will indicate either an OK message or a warning message for three seconds. Pressing the RESET control cycles the message center through each of the systems being monitored.


119


2009 Flex (471) Owners Guide, 2nd Printing USA (fus)


Driver Controls


The sequence of the system check report is as follows: 1. OIL LIFE 2. CHARGING SYSTEM 3. WASHER FLUID LEVEL 4. DOOR AJAR STATUS 5. BRAKE SYSTEM 6. DISTANCE TO EMPTY (DTE) Oil life An oil change is required whenever indicated by the message center. USE ONLY RECOMMENDED ENGINE OILS. To reset the oil monitoring system to 100% after each oil change (approximately 7,500 miles [12,000 km] or six months) perform the following: 1. Press the SETUP control to enter SYSTEM CHECK, then press SETUP control again to display “OIL LIFE = XXX% HOLD RESET = NEW”.


2. Press and hold the RESET control for two seconds and release. Oil life is set to 100% and “OIL LIFE SET TO 100%” is displayed. 3. While “OIL LIFE SET TO 100%” is displayed, if a lower oil life is desired, press and release the RESET control to reduce the value. Each press of the RESET control reduces the value by 10 percent. Note: Oil life of 100% equals 7,500 miles (12,000 km) or six months. For example, setting oil life to 60% sets the oil life value to 4,500 miles (7,200 km) and 108 days. Units (English/Metric) 1. Select this function from the SETUP menu for the current units to be displayed. 2. Press the RESET control to change from English to Metric.


120


2009 Flex (471) Owners Guide, 2nd Printing USA (fus)


Driver Controls


Autolamp delay This feature keeps your headlights on for up to three minutes after the ignition is switched off. 1. To disable/enable the autolamp delay feature, select this function from the SETUP menu for the current display mode. 2. Press the RESET control to select the new Autolamp delay values of 0, 10, 20, 30, 60, 90, 120 or 180 seconds. Autolock This feature automatically locks all vehicle doors when the vehicle is shifted into any gear, putting the vehicle in motion. 1. To disable/enable the autolock feature, select this function from the SETUP menu for the current display mode. 2. Press the RESET control to turn the autolock ON or OFF. Autounlock This feature automatically unlocks all vehicle doors when the driver’s door is opened within 10 minutes of the ignition being turned off. 1. To disable/enable the autounlock feature, select this function from the SETUP menu for the current display mode. 2. Press the RESET control switch to turn the autounlock ON or OFF. Easy entry/exit (if equipped) This feature automatically moves the drivers seat backwards for easy exit from the vehicle. 1. To disable/enable the easy entry/exit seat feature, select this function from the SETUP menu for the current display mode. 2. Press the RESET control to turn the easy entry/exit seat ON or OFF.


121


2009 Flex (471) Owners Guide, 2nd Printing USA (fus)


Driver Controls


Reverse Sensing System (Rear Park aid) This feature sounds a warning tone to warn the driver of obstacles near the rear bumper, and functions only when R (Reverse) gear is selected. 1. To disable/enable the reverse sensing system feature, select this function from the SETUP menu or put the vehicle in R (Reverse). 2. Press the RESET control to turn the rear park aid OFF or ON. Power Liftgate (if equipped) This feature allows users to open/close the rear liftgate at the touch of a button. 1. To disable/enable the power liftgate feature, select this function from the SETUP menu for the current display mode. 2. Press the RESET control to turn the power liftgate ON or OFF. Language 1. Select this function from the SETUP menu for the current language to be displayed. 2. Waiting four seconds or pressing the RESET control cycles the message center through each of the language choices. Selectable languages are English, Spanish, or French. 3. Press and hold the RESET control for two seconds to set the language choice. System warnings System warnings alert you to possible problems or malfunctions in your vehicle’s operating systems. In the event of a multiple warning situation, the message center will cycle the display to show all warnings by displaying each one for four seconds. The message center will display the last selected feature if there are no more warning messages. This allows you to use the full functionality of


122


2009 Flex (471) Owners Guide, 2nd Printing USA (fus)


Driver Controls


the message center after you acknowledge the warning by pressing the RESET control and clearing the warning message. Warning messages that have been reset are divided into two categories: • They will reappear on the display 10 minutes from the reset. • They will not reappear until an ignition off-on cycle has been


completed.


Status Warning cannot be reset


Warning returns after 10 minutes if condition still exists


This acts as a reminder that these warning conditions still exist within the vehicle. Warnings Driver door ajar Passenger door ajar Rear left door ajar Rear right door ajar Park brake engaged XXX miles (km) to E (empty) fuel level low Liftgate ajar Check fuel fill inlet Check brake system Brake fluid level low AWD off (if equipped) Check AWD (if equipped) Low tire pressure Tire pressure monitor fault Tire pressure sensor fault Oil life change soon Oil change required Inkey could not program


Warning returns after the ignition key is turned from off to on.


Maximum number of Integrated Keys exceeded


DRIVER DOOR AJAR — Displayed when the driver door is not completely closed. PASSENGER DOOR AJAR — Displayed when the passenger door is not completely closed. REAR LEFT DOOR AJAR — Displayed when the rear left door is not completely closed.


123


2009 Flex (471) Owners Guide, 2nd Printing USA (fus)


Driver Controls


REAR RIGHT DOOR AJAR — Displayed when the rear right door is not completely closed. PARK BRAKE ENGAGED — Displayed when the manual park brake is set, the engine is running and the vehicle is driven more than 3 mph (5 km/h). If the warning stays on after the park brake is released, contact your authorized dealer as soon as possible. XXX MILES TO E FUEL LEVEL LOW — Displayed as an early reminder of a low fuel condition. LIFTGATE AJAR — Displayed when the liftgate is not completely closed. Press RESET to reset display. CHECK FUEL FILL INLET — Displayed when the fuel fill inlet may not be properly closed. Refer to Easy Fuel™ “no cap” fuel system in the Maintenance and Specifications chapter. CHECK BRAKE SYSTEM — Displayed when the braking system is not operating properly. If the warning stays on or continues to come on, contact your authorized dealer as soon as possible. BRAKE FLUID LEVEL LOW — Indicates the brake fluid level is low and the brake system should be inspected immediately. Refer to Brake fluid in the Maintenance and Specifications chapter. AWD OFF (if equipped) — Displayed when the AWD system has been automatically disabled to protect itself. This is caused by operating the vehicle with the compact spare tire installed or if the system is overheating. The AWD system will resume normal function and clear this message after driving a short distance with the road tire re-installed or after the system is allowed to cool. CHECK AWD (if equipped) — Displayed when a problem exists with the AWD system. Contact your authorized dealer as soon as possible. LOW TIRE PRESSURE — Displayed when one or more tires on your vehicle have low tire pressure. Refer to Inflating your tires in the Tires, Wheels and Loading chapter. TIRE PRESSURE MONITOR FAULT — Displayed when the Tire Pressure Monitoring System is malfunctioning. If the warning stays on or continues to come on, contact your authorized dealer as soon as possible. TIRE PRESSURE SENSOR FAULT — Displayed when a tire pressure sensor is malfunctioning, or your spare tire is in use. For more information on how the system operates under these conditions, refer to Tire Pressure Monitoring System (TPMS) in the Tires, Wheels and


124


2009 Flex (471) Owners Guide, 2nd Printing USA (fus)


Driver Controls


Loading chapter. If the warning stays on or continues to come on, contact your authorized dealer as soon as possible. OIL LIFE CHANGE SOON — Displayed when the engine oil life remaining is 10% or less. When oil life left is between 10% and 0%, the XX% OIL LIFE CHANGE SOON message will be displayed. OIL CHANGE REQUIRED — Displayed when the oil life left reaches 0%, the OIL CHANGE REQUIRED message will be displayed. INTKEY COULD NOT PROGRAM — Displayed when an attempt is made to program a fifth Integrated Key to the Remote Key Entry System. For more information on Integrated Key, refer to Locks and Security chapter in this manual.


MANUAL LIFTGATE The liftgate area is only intended for cargo, not passengers. You can open and close the liftgate from outside the vehicle. The liftgate cannot be opened from the cargo area control button, only closed. Note: In the event of a power failure, the latch can be accessed and released from the inside using the access panel on the liftgate trim. To open the liftgate, push the control button located in the top of the liftgate pull cup handle to unlatch the liftgate, then pull on the outside handle to access the cargo area. • Do not open the liftgate in a garage or other enclosed area with a low ceiling. If the liftgate is opened, the liftgate could be damaged against a low ceiling.


• Do not leave the liftgate open while driving. Doing so could cause


serious damage to the liftgate and its components as well as allowing carbon monoxide to enter the vehicle.


WARNING: Make sure that the liftgate door is closed to prevent exhaust fumes from being drawn into the vehicle. This will also prevent passengers and cargo from falling out. If you must drive with the liftgate door open, keep the vents open so outside air comes into the vehicle.


125


2009 Flex (471) Owners Guide, 2nd Printing USA (fus)


Driver Controls


POWER LIFTGATE (PLG) (IF EQUIPPED) You can power open or close the liftgate with the following controls. • instrument panel control button • integrated keyhead transmitter button • outside liftgate control button • control button in the rear cargo area Note: The liftgate movement direction can be reversed with a second press of the instrument panel, or the rear cargo area control button, or a second double press of the integrated keyhead transmitter button. Opening and Closing the power liftgate:


WARNING: Make sure all persons are clear of the power liftgate area before using the power liftgate control.


WARNING: Keep keys out of reach of children. Do not allow children to play near an open or moving power liftgate.


The liftgate will only operate with the vehicle in P (Park). When the liftgate is being power closed, a chime will sound three times as the liftgate begins to power close. A single chime indicates a problem with the close request, caused by: • the ignition is in on and the transmission is not in Park • or the battery voltage is below the minimum operating voltage • or the vehicle speed is at or above 3 mph (5 km/h) If the liftgate reverses and starts to close after a open request, a fast continuous chime indicates excessive load on the gate or a possible strut failure. If any excessive load is removed and you still have a faster chime, have the system serviced immediately by your authorized dealer. Do not attempt to manually force the liftgate to travel faster than the power system will permit. This will activate the obstacle detection feature. Note: Cycling the ignition prior to completely latching the liftgate could result in damage to the liftgate and/or its power components. Make sure the liftgate is fully latched before operating the vehicle.


126


2009 Flex (471) Owners Guide, 2nd Printing USA (fus)


Driver Controls


Care should be exercised in starting the engine before the liftgate is fully closed (latched). If the ignition is cycled during a Liftgate Power Close cycle and the liftgate is 6-10 inches (15–24 cm) from being latched, the liftgate may reverse to the full open position. Verify that the gate is closed before operating or moving the vehicle, especially in an enclosure, like a garage or a parking structure. The liftgate or it components could be damaged in an enclosure, if the liftgate is open. When power operating the liftgate at temperatures below 32°F (0°C), the liftgate may stop about five inches (12.7 cm) from the full open position. The liftgate can be fully opened by pushing it upward to the maximum open position. The power liftgate feature can be enabled or disabled using the message center. With the control in the OFF position, power operation is disabled from the liftgate handle button and from the rear cargo area button. The integrated keyhead transmitter and instrument panel switch will still continue to operate the liftgate regardless of the position state of the message center. Refer to the Message center section in this chapter. To power open or close the liftgate from the instrument panel: Press the button, located on the instrument panel, once to power open or close the liftgate.


To power open or close the liftgate with the integrated keyhead transmitter: Press seconds to power open or close the liftgate. Refer to Remote entry system in the Locks and Security chapter.


twice within three


2009 Flex (471) Owners Guide, 2nd Printing USA (fus)


127


Driver Controls


To power open the liftgate with outside liftgate control button: 1. To open, unlock the liftgate with the integrated keyhead transmitter or power door unlock control. 2. To open the liftgate, push the control button located in the top of the liftgate pull cup handle. Note: For the best performance allow the power system to open the liftgate after pushing the control. Manually pushing or pulling the liftgate may activate the system’s obstacle detection feature and stop the power operation. To power close the liftgate with the rear cargo area control button: Press and release the control on the left rear quarter panel to close the liftgate. Note: The rear cargo area control button is disabled when the liftgate is latched (fully closed).


WARNING: Keep clear of the liftgate when activating the rear switch.


Note: The liftgate movement direction can be reversed with a second press of the instrument panel, or the rear cargo area control buttons, or a second double press of the integrated keyhead transmitter button. To manually operate the liftgate: 1. Disable the liftgate power function. Refer to the Message center in this chapter. 2. Open and close the liftgate as you would a standard liftgate. Refer to Manual liftgate in this chapter. Note: In case of operation in extreme cold -40°F (-40°C), or on extreme inclines, manual operation of the liftgate is suggested.


128


2009 Flex (471) Owners Guide, 2nd Printing USA (fus)


Driver Controls


Obstacle detection: The power liftgate system is equipped with an obstacle detection feature. If the power liftgate is closing, the system will reverse to full open when it detects an obstacle. A chime will sound three times when an obstacle is detected as the liftgate begins to reopen. Once the obstacle is removed, the liftgate can be closed under power. If the power liftgate is opening, the system will stop and a chime will sound three times when an obstacle is detected. Once the obstacle is removed, the liftgate can again be operated normally. Resetting the power liftgate: The power liftgate may not operate properly and may need to be reset if any of these conditions occur: • a low voltage or dead battery • disconnected battery • the liftgate is manually closed and left ajar (unlatched) To reset the power liftgate: 1. Disconnect the battery for 20 seconds then, reconnect the battery. 2. Manually close and fully latch the liftgate. 3. Power open the liftgate by using the integrated keyhead transmitter, or the instrument panel control button. Note: If the power liftgate system is turned off in the message center, the system cannot be activated with the outside release handle or rear cargo area control button. The system will need to be turned on to resume operation with the outside release handle or rear cargo area control button. The power liftgate is still operational through the use of the remote entry transmitter and instrument panel button when the power liftgate is turned off in the message center.


129


2009 Flex (471) Owners Guide, 2nd Printing USA (fus)


Driver Controls


CARGO AREA FEATURES


Cargo net (if equipped) The cargo pouch net secures lightweight objects in the cargo area. Attach the net to the anchors provided. Do not put more than 50 lb. (22 kg) in the net.


WARNING: The cargo net is not designed to restrain


objects during a collision or heavy braking.


LUGGAGE RACK The load must be placed directly on the luggage rack. The vehicle’s roof panel is not designed to carry a load. When loading the luggage rack, it is recommended to evenly distribute the load on the luggage rack and on dealer installed cross-bars (if equipped), as well as maintain a low center of gravity. Ensure that the load is securely fastened. The maximum load for the roof rack is 100 lb (45 kg). Your fuel economy will decrease when you drive with items on the luggage rack. When the rack is loaded, check the tightness of the load before driving and at each refueling stop.


130


2009 Flex (471) Owners Guide, 2nd Printing USA (fus)


Driver Controls


WARNING: Loaded vehicles, with a higher center of gravity, may handle differently than unloaded vehicles. Extra


precautions, such as slower speeds and increased stopping distance, should be taken when driving a heavily loaded vehicle.


131


2009 Flex (471) Owners Guide, 2nd Printing USA (fus)


Locks and Security


KEYS Your vehicle is equipped with two Integrated Keyhead Transmitters (IKTs). The IKT functions as both a programmed ignition key that operates all the locks and starts the vehicle, and a remote keyless entry transmitter. Vehicles with a power liftgate will have a four-button IKT while vehicles without a power liftgate will have a three-button IKT.


Your IKTs are programmed to your vehicle; using a non-programmed key will not permit your vehicle to start. If you lose your authorized dealer supplied IKTs, replacement IKTs are available through your authorized dealer. Standard SecuriLock™ keys without remote entry transmitter functionality can also be purchased from your authorized dealer if desired. Always carry a spare key with you in case of an emergency. For more information regarding programming replacement IKTs, refer to the SecuriLock™ passive anti-theft system section later in this chapter. Note: Your vehicle’s IKTs were issued with a security label on them that provides important vehicle key cut information. It is recommended that you maintain the label in a safe place for future reference, such as the inside front cover of this Owner’s Guide.


132


2009 Flex (471) Owners Guide, 2nd Printing USA (fus)


Locks and Security


Recommended handling of the Integrated Keyhead Transmitter (IKT) To avoid inadvertently activating the remote entry functions of your vehicle, it is recommended that the Integrated Keyhead Transmitter (IKT) be handled properly when starting and turning off your vehicle. When inserting the IKT into the ignition cylinder, place your thumb on the center thumb rest of the IKT and forefinger on the logo badge on the opposite side.


To gain more leverage when rotating the IKT in the ignition lock cylinder, you can readjust the location of your thumb to grasp the IKT on the control. outer edge next to the


Likewise, when rotating the IKT to the off position in the ignition lock cylinder, the bottom edge of the IKT adjacent to the utilized.


control can be


2009 Flex (471) Owners Guide, 2nd Printing USA (fus)


133


Locks and Security


POWER DOOR LOCKS • Press the • Press the


doors.


control to lock all


control to unlock all


doors.


Smart locks This feature helps to prevent you from locking yourself out of the vehicle if your key is still in the ignition. When you open one of the front doors or the liftgate and you lock the vehicle with the power door lock control (on the driver or passenger door trim panel), all the doors will lock, then all doors will automatically unlock reminding you that your key is still in the ignition. The vehicle can still be locked, with the key in the ignition, by locking the driver’s door with a key, using the lock control on the remote entry transmitter portion of your Integrated Keyhead Transmitter, or locking the vehicle with the keyless entry keypad. If both front doors and the liftgate are closed, the vehicle can be locked from any method, regardless of whether the key is in the ignition or not.


Autolock feature The autolock feature will lock all the doors when: • all the doors are closed, • the ignition is in the on position, • you shift into any gear putting the vehicle in motion, and • the vehicle attains a speed greater than 12 mph (20 km/h). The autolock feature repeats when: • any door is opened then closed while the ignition is in the on position • the vehicle then attains a speed greater than 12 mph (20 km/h).


and the vehicle speed is 9 mph (15 km/h) or lower, and


134


2009 Flex (471) Owners Guide, 2nd Printing USA (fus)


Locks and Security


Deactivating/activating autolock feature Your vehicle comes with the autolock features activated; there are four methods to enable/disable this feature: • Through your authorized dealer, • by using a power door unlock/lock procedure, • using a keypad procedure, or • or by using the instrument cluster message center. Refer to Message


center in the Driver Controls chapter.


Note: The autolock feature can be activated/deactivated independently of the autounlock feature. Power door lock switch autolock enable/disable procedure Before starting, ensure the ignition is in the off position and all vehicle doors are closed. You must complete Steps 1–5 within 30 seconds or the procedure will have to be repeated. If the procedure needs to be repeated, wait a minimum of 30 seconds before beginning again. 1. Place the key in the ignition and turn the ignition to the on position. 2. Press the power door unlock control on the door panel three times. 3. Turn the ignition from the on position to the off position. 4. Press the power door unlock control on the door panel three times. 5. Turn the ignition back to the on position. The horn will chirp one time to confirm programming mode has been entered and is active. 6. To enable/disable the autolock feature, press the unlock control, then press the lock control. The horn will chirp once if autolock was deactivated or twice (one short and one long chirp) if autolock was activated. 7. Turn the ignition to the off position. The horn will chirp once to confirm the procedure is complete.


135


2009 Flex (471) Owners Guide, 2nd Printing USA (fus)


Locks and Security


Keyless entry keypad autolock enable/disable procedure 1. Turn the ignition to the off position. 2. Close all the doors. 3. Enter factory–set 5–digit entry code. 4. Touch and hold the 3 • 4. While holding the 3 • 4 touch the 7 • 8. 5. Release the 7 • 8. 6. Release the 3 • 4.


The user should receive a horn chirp to indicate the system has been disabled or a chirp followed by a honk to indicate the system has been enabled. Autounlock feature The autounlock feature will unlock all the doors when: • the ignition is in the on position, all the doors are closed, and the vehicle has been in motion at a speed greater than 12 mph (20 km/h); • the vehicle has then come to a stop and the ignition is turned to the • the driver door is opened within 10 minutes of the ignition being


off or accessory position; and


transitioned to the off or accessory position.


Note: The doors will not autounlock if the vehicle has been electronically locked before the driver door is opened. Deactivating/activating autounlock feature Your vehicle comes with the autounlock features activated; there are four methods to enable/disable this feature: • Through your authorized dealer, • by using a power door unlock/lock sequence, • using a keypad procedure, or • or by using the instrument cluster message center. Refer to Message


center in the Driver Controls chapter.


136


2009 Flex (471) Owners Guide, 2nd Printing USA (fus)


Locks and Security


Note: The autounlock feature can be activated/deactivated independently of the autolock feature. Power door lock switch autounlock enable/disable procedure Before starting, ensure the ignition is in the off position and all vehicle doors are closed. You must complete Steps 1–5 within 30 seconds or the procedure will have to be repeated. If the procedure needs to be repeated, wait a minimum of 30 seconds before beginning again. 1. Place the key in the ignition and turn the ignition to the on position. 2. Press the power door unlock control on the door panel three times. 3. Turn the ignition from the on position to the off position. 4. Press the power door unlock control on the door panel three times. 5. Turn the ignition back to the on position. The horn will chirp one time to confirm programming mode has been entered and is active. 6. To enable/disable the autounlock feature, press the lock control, then press the unlock control. The horn will chirp once if autounlock was deactivated or twice (one short and one long chirp) if autounlock was activated. 7. Turn the ignition to the off position. The horn will chirp once to confirm the procedure is complete.


137


2009 Flex (471) Owners Guide, 2nd Printing USA (fus)


Locks and Security


Keyless entry keypad autounlock enable/disable procedure 1. Turn the ignition to the off position. 2. Close all the doors. 3. Enter factory–set 5–digit entry code. 4. Touch and hold the 3 • 4. While holding the 3 • 4, touch and release the 7 • 8. While still holding the 3 • 4, touch and release the 7 • 8 a second time. 5. Release the 3 • 4.


The user should receive a horn chirp to indicate the system has been disabled or a chirp followed by a honk to indicate the system has been enabled.


CHILDPROOF DOOR LOCKS • When these locks are set, the


rear doors cannot be opened from the inside.


• The rear doors can be opened


from the outside when the doors are unlocked.


The childproof locks are located on rear edge of each rear door and must be set separately for each door. Setting the lock for one door will not automatically set the lock for both doors. • Insert the key and turn to the lock position (key horizontal) to engage the childproof locks. • Insert the key and turn to the unlock position (key vertical) to disengage the childproof locks.


138


2009 Flex (471) Owners Guide, 2nd Printing USA (fus)


Locks and Security


REMOTE ENTRY SYSTEM The Integrated Keyhead Transmitter (IKT) complies with part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. There are two possible types of IKTs: • Vehicles equipped with a power


liftgate


139


2009 Flex (471) Owners Guide, 2nd Printing USA (fus)


Locks and Security • Vehicles not equipped with a


power liftgate


The typical operating range for your IKT is approximately 33 feet (10 meters). A decrease in operating range could be caused by: • weather conditions, • nearby radio towers, • structures around the vehicle, or • other vehicles parked next to your vehicle. The IKT allows you to: • remotely unlock the vehicle doors. • remotely lock all the vehicle doors. • remotely open the power liftgate (if equipped). • activate the personal alarm. • arm and disarm the perimeter anti-theft system. • operate the illuminated entry feature. The remote entry lock/unlock feature operates in any ignition position except while the key is held in the start position. The panic feature operates with the key in the off position. If there are problems with the remote entry system, make sure to take ALL Integrated Keyhead Transmitters with you to the authorized dealer in order to aid in troubleshooting the problem. Unlocking the doors/two stage unlock 1. Press lamps will illuminate.


and release to unlock the driver’s door. Note: The interior


140


2009 Flex (471) Owners Guide, 2nd Printing USA (fus)


Locks and Security


and release again within three seconds to unlock all the


2. Press doors. The remote entry system activates the illuminated entry feature; this feature turns on the lamps for 25 seconds or until the ignition is turned to the on position. The inside lights will not turn off if: • they have been turned on using the dimmer control or • any door is open. The battery saver feature will turn off the interior lamps 10 minutes after the ignition is turned to the off position. Two stage unlocking may be disabled or re-enabled by simultaneously controls on the IKT for four seconds (disabling pressing the two stage unlock allows all vehicle doors to unlock simultaneously). The turn lamps will flash twice to indicate that two-stage unlock was enabled or disabled.


and


and release to lock all the doors. The turn lamps will flash. and release again within three seconds to confirm that all


Locking the doors 1. Press 2. Press the doors are closed. Note: The doors will lock again, the horn will chirp and the turn lamps will flash once if all the doors and liftgate are closed. Note: If any door or the liftgate is not closed, the horn will chirp twice and the lamps will not flash.


Opening the power liftgate (if equipped) Press liftgate.


twice within three seconds to fully unlatch and open the


WARNING: Make sure all persons are clear of the liftgate area before using power liftgate control.


In order to fully lower and latch the liftgate, press the control twice. If the liftgate stops mid travel, it may have detected an obstacle, Check to ensure the liftgate swing zone is free from obstruction and reset the power assist by manually closing the liftgate. Normal operation can then be resumed.


141


2009 Flex (471) Owners Guide, 2nd Printing USA (fus)


Locks and Security


WARNING: Make sure the liftgate is closed to prevent exhaust fumes from being drawn into the vehicle. This will also prevent


passengers and cargo from falling out. If you must drive with the liftgate open, keep the vents open so outside air comes into the vehicle.


Car finder twice within three seconds. The horn will chirp and the turn Press lamps will flash. It is recommended that this method be used to locate your vehicle, rather than using the panic alarm.


to activate the alarm. The horn will sound and the turn lamps


Sounding a panic alarm Press will flash for a maximum of three minutes. Press again or turn the ignition to the on position to deactivate, or wait for the alarm to time out in three minutes. Note: The panic alarm will only operate when the ignition is in the off position.


to automatically move the seat, mirrors and adjustable pedals


Memory seats/power mirrors/adjustable pedals (if equipped) The Integrated Keyhead Transmitter allows you to recall the memory seat/power mirrors/adjustable pedals feature. Press (if equipped) to the desired memory position. Note: The seat will not travel to its final position if the key is not in the ignition and the easy entry feature is enabled. Activating the memory feature To activate this feature: 1. Position the seat, mirrors, and adjustable pedals (if equipped) to the desired positions. 2. Press and hold either the 1 or 2
control on the driver’s door for five seconds. (A tone will be heard after 11⁄2 seconds when the memory store is done) continue to hold until a second tone is heard after five seconds.


142


2009 Flex (471) Owners Guide, 2nd Printing USA (fus)


Locks and Security


control on the Integrated Keyhead


3. Within three seconds press the Transmitter. 4. A tone will be heard when the activation is complete. 5. Repeat this procedure for another Integrated Keyhead Transmitter if desired. Deactivating the memory feature To deactivate this feature: 1. Press and hold either the 1 or 2 control on the driver’s door for five seconds. (A tone will be heard after 11⁄2 seconds when the memory store is done) continue to hold until a second tone is heard after five seconds. control on the Integrated Keyhead 2. Within three seconds press the Transmitter. 3. A tone will be heard when the deactivation is complete. 4. Repeat this procedure for another Integrated Keyhead Transmitter if desired.


Replacing the battery The Integrated Keyhead Transmitter uses one coin type three-volt lithium battery CR2032 or equivalent. To replace the battery: 1. Twist a thin coin in the slot of the IKT near the key ring in order to remove the battery cover.


2. Do not wipe off any grease on the battery terminals on the back surface of the circuit board. 3. Remove the old battery. Note: Please refer to local regulations when disposing of transmitter batteries.


2009 Flex (471) Owners Guide, 2nd Printing USA (fus)


143


Locks and Security


4. Insert the new battery. Refer to the instructions inside the IKT for the correct orientation of the battery. Press the battery down to ensure that the battery is fully seated in the battery housing cavity. 5. Snap the battery cover back onto the key. Note: Replacement of the battery will not cause the IKT to become deprogrammed from your vehicle. The IKT should operate normally after battery replacement.


Replacing lost Integrated Keyhead Transmitters (IKTs) If you would like to have your Integrated Keyhead Transmitters reprogrammed because you lost one, or would like to buy additional IKTs, you can either reprogram them yourself, or take all IKTs to your authorized dealer for reprogramming. How to reprogram your Integrated Keyhead Transmitters (IKTs) To program a new Integrated Keyhead Transmitter yourself, refer to Programming spare keys in the SecuriLock™ passive anti-theft system section of this chapter. Note: At least two IKTs are required to perform this procedure yourself.


Illuminated entry The interior lamps and puddle lamps (if equipped) illuminate when the Integrated Keyhead Transmitter or the keyless entry system keypad is used to unlock the door(s). The illuminated entry system will turn off the interior lights if: • the ignition is turned to the on position, or • the Integrated Keyhead Transmitter • the vehicle is locked using the keyless entry keypad, or • after 25 seconds of illumination. The inside lights will not turn off if: • they have been turned on with the dimmer control, or • any door is open.


control is pressed, or


144


2009 Flex (471) Owners Guide, 2nd Printing USA (fus)


Locks and Security


control on the transmitter is pressed:


Perimeter lamps illuminated entry With the Integrated Keyhead Transmitter system, the following items will illuminate when the • Headlamps • Park lamps • Tail lamps The lamps will automatically turn off: • if the ignition switch is turned to the on position, or • the Integrated Keyhead Transmitter lock control is pressed, or • the vehicle is locked using the keyless entry keypad, or • after 25 seconds of illumination. Note: On some vehicles, the perimeter lamps illuminated entry feature will not activate in daylight conditions. Deactivating/activating perimeter lamps illuminated entry You may enable/disable this feature by having your vehicle serviced by your authorized dealer. You may also perform the following power door lock sequence to enable/disable the perimeter lamps feature. Note: Before starting, ensure the ignition is in the 1 (off) position and all vehicle doors are closed. You must complete Steps 1–5 within 30 seconds or the procedure will have to be repeated. If the procedure needs to be repeated, wait a minimum of 30 seconds before beginning again. 1. Place the key in the ignition and turn the ignition to the 3 (on) position. 2. Press the power door unlock control on the door panel three times. 3. Turn the ignition from the 3 (on) position to the 1 (off) position. 4. Press the power door unlock control on the door panel three times. 5. Turn the ignition back to the 3 (on) position. The horn will chirp one time to confirm programming mode has been entered and is active.


145


2009 Flex (471) Owners Guide, 2nd Printing USA (fus)


Locks and Security


6. Press the power door unlock control twice within five seconds. Note: The horn will chirp once to indicate the perimeter lighting feature has been deactivated. The horn will chirp once and honk once (one short and one long) to indicate the perimeter lighting feature has been activated. 7. Turn the ignition to the 1 (off) position to exit the procedure. Note: The horn will chirp once to confirm the procedure is complete.


Illuminated exit • When all vehicle doors are closed and the key is removed from the ignition, the interior dome lamps (and the exterior mirror puddle lamps, if equipped) will illuminate.


The lights will turn off if all the doors remain closed and • 25 seconds elapse, or • the key is inserted in the ignition. Battery saver The battery saver will shut off the interior lamps 10 minutes after the ignition has been turned to the off position. • If the dome lamps were turned on using the panel dimmer control, the battery saver will shut them off 10 minutes after the ignition has been turned to the off position. • If the courtesy lamps were turned on because one of the vehicle doors


or the liftgate was opened, the battery saver will shut off them off 10 minutes after the ignition has been turned to the off position. • The battery saver will shut off the headlamps 10 minutes after the


ignition has been turned to the off position.


146


2009 Flex (471) Owners Guide, 2nd Printing USA (fus)


Locks and Security


SECURICODE™ KEYLESS ENTRY SYSTEM The keypad is invisible until touched and then it lights up so you can see and touch appropriate buttons. You can use the keyless entry keypad to: • lock or unlock the doors without • recall memory seat, power


using a key.


mirrors, and adjustable pedals (if equipped).


The keypad can be operated with the factory set 5–digit entry code; this code is located on the owner’s wallet card in the glove box and is available from your authorized dealer. You can also create up to three of your own 5–digit personal entry codes. When touching the controls on the keypad, touch the middle of the controls.


Programming a personal entry code and keypad association to memory seats, mirrors, and adjustable pedals (if equipped) To create your own personal entry code: 1. Enter the factory set code. 2. Within five seconds touch the 1 • 2 on the keypad. 3. Enter your personal 5-digit code. Each number must be entered within five seconds of each other. 4. For memory recall feature, enter the sixth digit 1 • 2 to store driver 1
settings or 3 • 4 to store driver 2 settings. Note: Touching 5 • 6, 7 • 8, or 9 • 0 keypad numbers as a sixth digit will not recall a driver memory setting. Note: The factory-set code cannot be associated with a memory setting. 5. The doors will lock then unlock to confirm that your personal entry code has been programmed to the module.


147


2009 Flex (471) Owners Guide, 2nd Printing USA (fus)


Locks and Security


Tips: • Do not set a code that uses five of the same number. • Do not use five numbers in sequential order. • The factory set code will work even if you have set your own personal


code.


Erasing personal code 1. Enter the factory set 5–digit code. 2. Within five seconds, touch the 1 • 2 on the keypad and release. 3. Touch and hold the 1 • 2 for two seconds. This must be done within five seconds of completing Step 2. All personal codes are now erased and only the factory set 5–digit code will work.


your Integrated Keyhead Transmitter.


control on the remote entry transmitter portion of


Anti-scan feature If the wrong code has been entered seven times (35 consecutive number touches), the keypad will go into an anti-scan mode. This mode disables the keypad for one minute and the keypad lamp will flash. The anti-scan feature will turn off after: • one minute of keypad inactivity. • pressing the • the ignition is turned on. Unlocking and locking the doors using keyless entry To unlock the driver’s door, enter the factory set 5-digit code or your personal code. Each number must be touched within five seconds of each other. The interior lamps will illuminate. Note: If the two-stage unlocking feature is disabled, all doors will unlock; for more information regarding two-stage unlocking, refer to the Unlocking the doors/Two stage unlock section earlier in this chapter. To unlock all doors, enter the factory set code or your personal code, then touch the 3 • 4 control within five seconds. To lock all doors, touch the 7 • 8 and the 9 • 0 at the same time (with the driver’s door closed) for two seconds. You do not need to enter the keypad code first.


148


2009 Flex (471) Owners Guide, 2nd Printing USA (fus)


Locks and Security


SECURILOCK™ PASSIVE ANTI-THEFT SYSTEM SecuriLock™ passive anti-theft system is an engine immobilization system. This system is designed to help prevent the engine from being started unless a coded Integrated Keyhead Transmitter (IKT) programmed to your vehicle is used. The use of the wrong type of coded key may lead to a “no-start” condition. Your vehicle comes with two coded Integrated Keyhead Transmitters; additional coded IKTs may be purchased from your authorized dealer. Standard SecuriLock™ keys without remote entry transmitter functionality can also be purchased from your authorized dealer if desired. The authorized dealer can program your spare IKTs to your vehicle or you can program the IKTs yourself. Refer to Programming spare keys for instructions on how to program the coded key. Note: The SecuriLock™ passive anti-theft system is not compatible with non-Ford aftermarket remote start systems. Use of these systems may result in vehicle starting problems and a loss of security protection. Note: Large metallic objects, electronic devices that are used to purchase gasoline or similar items, or a second coded key on the same key chain may cause vehicle starting issues. You need to prevent these objects from touching the coded IKT while starting the engine. These objects will not cause damage to the coded IKT, but may cause a momentary issue if they are too close to the IKT when starting the engine. If a problem occurs, turn the ignition off, remove all objects on the key chain away from the coded IKT and restart the engine. Note: Do not leave a duplicate coded key in the vehicle. Always take your keys and lock all doors when leaving the vehicle.


149


2009 Flex (471) Owners Guide, 2nd Printing USA (fus)


Locks and Security


Anti-theft indicator The anti-theft indicator is located in the instrument panel cluster. • When the ignition is in the off position, the indicator will flash once every two seconds to indicate the SecuriLock™ system is functioning as a theft deterrent.


• When the ignition is in the on position, the indicator will glow for


three seconds to indicate normal system functionality.


If a problem occurs with the SecuriLock™ system, the indicator will flash rapidly or glow steadily when the ignition is in the on position. If this occurs, turn the ignition off then back to on to make sure there was no electronic interference with the programmed key. If the vehicle doesn’t start, try to start it with the 2nd programmed key and if successful contact your authorized dealership for key replacement. If the indicator still flashes rapidly or glows steadily, the vehicle will not start, contact your authorized dealer as soon as possible for service.


Automatic arming The vehicle is armed immediately after switching the ignition to the off position. The theft indicator will flash every two seconds to act as a theft deterrent when the vehicle is armed.


Automatic disarming The vehicle is disarmed immediately after the ignition is turned to the on position. The theft indicator will illuminate for three seconds and then go out. If the theft indicator stays on for an extended period of time or flashes rapidly, contact your authorized dealer as soon as possible.


150


2009 Flex (471) Owners Guide, 2nd Printing USA (fus)


Locks and Security


Replacement Integrated Keyhead Transmitters (IKT) and coded keys Note: Your vehicle comes equipped with two Integrated Keyhead Transmitters (IKTs). The IKT functions as both a programmed ignition key that operates all the locks and starts the vehicle, as well as a remote keyless entry transmitter. A maximum of eight coded keys can be programmed to your vehicle; only four of these eight keys can be IKTs with remote entry functionality. If your IKTs or standard SecuriLock™ coded keys are lost or stolen and you don’t have an extra coded key, you will need to have your vehicle towed to an authorized dealer. The key codes need to be erased from your vehicle and new coded keys will need to be programmed. Replacing coded keys can be very costly. Store an extra programmed key away from the vehicle in a safe place to help prevent any inconveniences. Please visit an authorized dealer to purchase additional spare or replacement keys.


Programming spare keys You can program your own Integrated Keyhead Transmitters or standard SecuriLock™ coded keys to your vehicle. This procedure will program both the engine immobilizer keycode and the remote entry transmitter portion of the IKT to your vehicle. Note: A maximum of eight coded keys can be programmed to your vehicle; only four of these eight can be IKTs with remote entry functionality. Tips: • Only use Integrated Keyhead Transmitters (IKTs) or standard • You must have two previously programmed coded keys (keys that already operate your vehicle’s engine) and the new unprogrammed key(s) readily accessible.


• If two previously programmed coded keys are not available, you must take your vehicle to your authorized dealer to have the spare key(s) programmed.


SecuriLock™ keys.


151


2009 Flex (471) Owners Guide, 2nd Printing USA (fus)


Locks and Security


Please read and understand the entire procedure before you begin. 1. Insert the first previously programmed coded key into the ignition. 2. Turn the ignition from the 1 (off) position to the 3 (on) position. Keep the ignition in the 3 (on) position for at least three seconds, but no more than 10 seconds. 3. Turn the ignition to the 1 (off) position and remove the first coded key from the ignition. 4. Within 10 seconds of turning the ignition to the 1 (off) position, insert the second previously coded key into the ignition. 5. Turn the ignition from the 1 (off) position to the 3 (on) position. Keep the ignition in the 3 (on) position for at least three seconds, but no more than 10 seconds. 6. Turn the ignition to the 1 (off) position and remove the second previously programmed coded key from the ignition. 7. Within 20 seconds of turning the ignition to the 1 (off) position and removing the previously programmed coded key, insert the new unprogrammed key (new key/valet key) into the ignition. 8. Turn the ignition from the 1 (off) position to the 3 (on) position. Keep the ignition in the 3 (on) position for at least six seconds. 9. Remove the newly programmed coded key from the ignition. If the key has been successfully programmed it will start the vehicle’s engine and will operate the remote entry system (if the new key is an Integrated Keyhead Transmitter). The theft indicator light will illuminate for three seconds and then go out to indicate successful programming. If the key was not successfully programmed, it will not start your vehicle’s engine and/or will not operate the remote entry features. The theft indicator light may flash on and off. Wait 20 seconds and you may repeat Steps 1 through 8. If failure repeats, bring your vehicle to your authorized dealer to have the new key(s) programmed. To program additional new unprogrammed key(s), wait 20 seconds and then repeat this procedure from Step 1.


152


2009 Flex (471) Owners Guide, 2nd Printing USA (fus)


Locks and Security


PERIMETER ALARM SYSTEM (IF EQUIPPED) The perimeter anti-theft system will help protect your vehicle from unauthorized entry. If there is any potential perimeter anti-theft problem with your vehicle, ensure ALL Integrated Keyhead Transmitters are brought to the authorized dealer to aid in troubleshooting.


Arming the system When armed, this system will respond if unauthorized entry is attempted. When unauthorized entry occurs, the system will flash the turn signal lamps and will sound the horn. The system is ready to arm whenever the key is in the off position, or is removed from the ignition. Either of the following actions will prearm the alarm system: • Press the


control on the remote entry transmitter portion of your


Integrated Keyhead Transmitter. When you press the lock control twice within three seconds on the remote entry transmitter portion of your IKT, the horn will chirp once to let you know that all doors, the hood and the liftgate are closed. If any of these are not closed, the horn will chirp twice to warn you that a door, the hood or the liftgate is still open.


• Press the driver or passenger interior door lock control while the door is open, then close the door.


153


2009 Flex (471) Owners Guide, 2nd Printing USA (fus)


Locks and Security • Touch the 7 • 8 and 9 • 0
controls on the keyless entry pad at the same time to lock the doors (driver’s door must be closed).


There is a 20 second countdown when any of the above actions occur before the vehicle becomes armed. Each door, the hood, and the liftgate is armed individually, and if any are open, they must be closed before the open entry point (door, hood, or liftgate) can enter the 20 second countdown. The turn signal lamps will flash once when all doors, the hood and the liftgate are closed indicating the vehicle is locked and entering the 20 second countdown.


your Integrated Keyhead Transmitter.


Disarming the system You can disarm the system by any of the following actions: • Unlock the doors by using the remote entry transmitter portion of • Unlock the doors by using your keyless entry pad. • Unlock the driver’s door with a key. Turn the key full rearward (toward the rear of the vehicle) to ensure the alarm disarms. • Turn ignition to the on position with a valid SecuriLock™ key or • Press the panic control on the remote entry transmitter portion of your IKT. This will only shut off the horn and turn lamps when the alarm is sounding. The alarm system will still be armed.


Integrated Keyhead Transmitter (IKT).


Pressing the power door unlock control within the 20 second prearmed mode will return the vehicle to a disarmed state. Triggering the anti-theft system The armed system will be triggered if: • Any door, the hood or the liftgate is opened without using the door • The ignition is turned to the on position with an invalid SecuriLock™


key, keypad or the remote entry transmitter portion of your IKT.


key or IKT.


154


2009 Flex (471) Owners Guide, 2nd Printing USA (fus)


Seating and Safety Restraints


SEATING


WARNING: Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal


injuries in the event of a collision.


WARNING: Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop.


WARNING: Before returning the seatback to its original position, make sure that cargo or any objects are not trapped


behind the seatback. After returning the seatback to its original position, pull on the seatback to ensure that it has fully latched. An unlatched seat may become dangerous in the event of a sudden stop or collision.


Adjustable head restraints Your vehicle is equipped with front row outboard head restraints that are vertically adjustable.


WARNING: To minimize the risk of neck injury in the event of a crash, the driver and passenger occupants should not sit in and/or operate the vehicle, until the head restraint is placed in its proper position. The driver should never adjust the head restraint while the vehicle is in motion.


The adjustable head restraints consist of: • a trimmed energy absorbing foam and structure (1), • two steel stems (2), • a guide sleeve adjust/release • and a guide sleeve unlock/remove


button (3),


button (4).


155


2009 Flex (471) Owners Guide, 2nd Printing USA (fus)


Seating and Safety Restraints


To adjust the head restraint, do the following: 1. Adjust the seatback to an upright driving/riding position. Refer to Adjusting the front manual seat later in this chapter. 2. Raise the head restraint by pulling up on the head restraint.


3. Lower the head restraint by pressing and holding the guide sleeve adjust/release button and pushing down on the head restraint.


Properly adjust the head restraint so that the top of the head restraint is even with the top of your head and positioned as close as possible to the back of your head. For occupants of extremely tall stature, adjust the head restraint to its full up position.


WARNING: The adjustable head restraint is a safety device. Whenever possible it should be installed and properly adjusted


when the seat is occupied.


156


2009 Flex (471) Owners Guide, 2nd Printing USA (fus)


Seating and Safety Restraints


To remove the adjustable head restraint, do the following: 1. Pull up the head restraint until it reaches the highest adjustment position.


2. Simultaneously press and hold both the adjust/release button and the unlock/remove button, then pull up on the head restraint.


To reinstall the adjustable head restraint, do the following: 1. Insert the two stems into the guide sleeve collars. 2. Push the head restraint down until it locks.


Properly adjust the head restraint so that the top of the head restraint is even with the top of your head and positioned as close as possible to the back of your head. For occupants of extremely tall stature, adjust the head restraint to its full up position.


157


2009 Flex (471) Owners Guide, 2nd Printing USA (fus)


Seating and Safety Restraints


WARNING: To minimize the risk of neck injury in the event of a crash, head restraints must be installed properly.


Adjusting the front manual seat (if equipped)


WARNING: Never adjust the driver’s seat or seatback when the vehicle is moving.


WARNING: Always drive and ride with your seatback upright and the lap belt snug and low across the hips.


Lift handle to move seat forward or backward.


Pull lever up to adjust seatback.


WARNING: Before returning the seatback to its


original position, make sure that cargo or any objects are not trapped behind the seatback. After returning the seatback to its original position, pull on the seatback to ensure that it has fully latched. An unlatched seat may become dangerous in the event of a sudden stop or collision.


158


2009 Flex (471) Owners Guide, 2nd Printing USA (fus)


Seating and Safety Restraints


Using the manual lumbar support (if equipped) The lumbar control is located on the side of the seat cushion. Turn to adjust lumbar support. Rotate the lumbar forward to adjust firmness. Rotate the lumbar rearward to adjust softness.


Folding down the front passenger seatback The front passenger seatback can be folded to a horizontal position to make room for a long load. To fold the seatback: 1. Move the seat as far back as possible. 2. Push the head restraint release button and move the head restraint fully down. 3. Put the seatback in the most upright position. 4. Pull the strap located on the back of the seat to fold the front passenger seatback. 5. Without releasing the pull strap, push the seatback forward.


WARNING: Cover sharp edges on the load and properly secure the load to prevent injury to occupants from shifting load during


sudden stops.


WARNING: Before returning the seatback to its original position, make sure that cargo or any objects are not trapped


behind the seatback. After returning the seatback to its original position, pull on the seatback to ensure that it has fully latched. An unlatched seat may become dangerous in the event of a sudden stop or collision.


159


2009 Flex (471) Owners Guide, 2nd Printing USA (fus)


Seating and Safety Restraints


Adjusting the front power seat (if equipped)


WARNING: Never adjust the driver’s seat or seatback when the vehicle is moving.


WARNING: Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop.


WARNING: Always drive and ride with your seatback upright and the lap belt snug and low across the hips.


WARNING: Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal


injuries in the event of a collision.


WARNING: Sitting improperly out of position or with the seat back reclined too far can take off weight from the seat cushion and affect the decision of the passenger sensing system, resulting in serious injury or death in a crash. Always sit upright against your seatback, with your feet on the floor.


WARNING: To reduce the risk of possible serious injury: Do not hang objects off seat back or stow objects in map pocket (if


equipped) when a child is in the front passenger seat. Do not place objects underneath the front passenger seat or between the seat and the center console (if equipped). Check the “passenger airbag off” or “pass airbag off” indicator lamp for proper airbag status. Refer to Front passenger sensing system section for additional details. Failure to follow these instructions may interfere with the front passenger seat sensing system.


160


2009 Flex (471) Owners Guide, 2nd Printing USA (fus)


Seating and Safety Restraints


Move the front of the control up or down to tilt the seat cushion.


Move the rear of the control up or down to raise or lower the seat cushion.


Move the control in the directions shown to move the seat forward or backward.


Press the control to recline the seatback forward or rearward.


161


2009 Flex (471) Owners Guide, 2nd Printing USA (fus)


Seating and Safety Restraints


Using the power lumbar support (if equipped) The power lumbar control is located on the outboard side of the seat. Press the forward side of the control to adjust firmness. Press the rearward side of the control to adjust softness.


Heated seats (if equipped)


WARNING: Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord


injury, medication, alcohol use, exhaustion, or other physical conditions, must exercise care when using the seat heater. The seat heater may cause burns even at low temperatures, especially if used for long periods of time. Do not place anything on the seat that insulates against heat, such as a blanket or cushion, because this may cause the seat heater to overheat. Do not puncture the seat with pins, needles, or other pointed objects because this may damage the heating element which may cause the seat heater to overheat. An overheated seat may cause serious personal injury.


Note: Do not do the following: • Place heavy objects on the seat • Operate the seat heater if water or any other liquid is spilled on the


seat. Allow the seat to dry thoroughly.


To operate the heated seats: • Push the control located on the


climate control system panel once to activate high heat. • Push twice to activate low heat. • Push a third time to deactivate. The indicator light on the control will illuminate when activated. For low heat, one light will be lit; for high heat, both lights will be lit.


162


2009 Flex (471) Owners Guide, 2nd Printing USA (fus)


Seating and Safety Restraints


Memory seat/power mirrors/adjustable pedals (if equipped) This system allows automatic positioning of the driver seat, outside rearview mirrors and adjustable pedals to two programmable positions. The memory seat control is located on the driver door. • To program position one, move the driver seat, exterior mirrors and adjustable pedals to the desired positions using the associated controls. Press and hold control button 1 for at least two seconds.


button 2.


• To program position two, repeat the previous procedure using control • A tone will be heard when the memory save is complete. A position can only be recalled when the transmission gearshift is in Park (automatic transmission). A memory seat position may be programmed at any time. The memory seat positions are also recalled when you press your remote entry transmitter programmed to a memory seat position or when you enter a valid customer code 1 or 2 on the keypad. To program the memory seat to remote entry transmitter, refer to Remote entry system in the Locks and Security chapter.. Note: The seat will not travel to its final position if the key is not in the ignition and the easy entry feature is enabled.


(unlock) control and the transmitter is


Easy entry/exit feature (if equipped) This feature automatically moves the driver’s seat rearward 2 in (5 cm) when: • the transmission is in N (Neutral) or P (Park) • the key is removed from the ignition The seat will move to the original position when: • the transmission is in N (Neutral) or P (Park) • the key is placed in the ignition. The easy entry feature can be turned off or on through the vehicle message center. Refer to Message center in the Driver controls chapter.


163


2009 Flex (471) Owners Guide, 2nd Printing USA (fus)


Seating and Safety Restraints


REAR SEATS


Head restraints Lift the head restraint so that it is located directly or as close as possible behind your head. The head restraints can be moved up by pulling up on the head restraint.


Push the release button to lower head restraint.


WARNING: The adjustable head restraint is a safety device. Whenever possible it should be installed and properly adjusted


when the seat is occupied.


164


2009 Flex (471) Owners Guide, 2nd Printing USA (fus)


Seating and Safety Restraints


To remove the adjustable head restraint, do the following: 1. Pull up the head restraint until it reaches the highest adjustment position.


2. Press and hold the unlock/remove button, then pull up on the head restraint.

Loading...
x