2014 Ford Fiesta Owners Manual

22

Fiesta (CCT) Vehicles Built From: 01-04-2013, Vehicles Built Up To: 31-12-2013

Child Safety

• Does the lap belt rest low across the

hips? Is the shoulder belt centered on the shoulder and chest?

• Can the child stay seated like this for

the whole trip?

Always use booster seats in conjunction with your vehicle lap and shoulder belt. Types of Booster Seats

Backless booster seats

• If your backless booster seat has a removable shield, remove the shield. If a vehicle seating position has a low seat back or no head restraint, a backless booster seat may place your child's head (as measured at the tops of the ears) above the top of the seat. In this case, move the backless booster to another seating position with a higher seat back or head restraint and lap and shoulder belts, or consider using a high back booster seat.

BOOSTER SEATS

WARNING

•

Never place, or allow a child to place, the shoulder belt under a child's arm or behind the back because it

reduces the protection for the upper part of the body and may increase the risk of injury or death in a crash.

Use a belt-positioning booster seat for children who have outgrown or no longer properly fit in a child safety seat (generally children who are less than 4 feet 9 inches (1.45 meters) tall, are greater than age four (4) and less than age twelve (12), and between 40 pounds (18 kilograms) and 80 pounds (36 kilograms) and upward to 100 pounds (45 kilograms) if recommended by your child restraint manufacturer). Many state and provincial laws require that children use approved booster seats until they reach age eight, a height of 4 feet 9 inches (1.45 meters) tall, or 80 pounds (36 kilograms). Booster seats should be used until you can answer YES to ALL of these questions when seated without a booster seat:

• Can the child sit all the way back

against their vehicle seat back with knees bent comfortably at the edge of the seat cushion?

• Can the child sit without slouching?

23

Fiesta (CCT) Vehicles Built From: 01-04-2013, Vehicles Built Up To: 31-12-2013

E142595E68924Child Safety

If, with a backless booster seat, you cannot find a seating position that adequately supports your child's head, a high back booster seat would be a better choice. Children and booster seats vary in size and shape. Choose a booster that keeps the lap belt low and snug across the hips, never up across the stomach, and lets you adjust the shoulder belt to cross the chest and rest snugly near the center of the shoulder. The following drawings compare the ideal fit (center) to a shoulder belt uncomfortably close to the neck and a shoulder belt that could slip off the shoulder. The drawings also show how the lap belt should be low and snug across the child's hips.

• High back booster seats

24

Fiesta (CCT) Vehicles Built From: 01-04-2013, Vehicles Built Up To: 31-12-2013

E70710E142596E142597Child Safety

Right-Hand Side Turn clockwise to lock and counterclockwise to unlock.

If the booster seat slides on the vehicle seat upon which it is being used, placing a rubberized mesh sold as shelf or carpet liner under the booster seat may improve this condition. Do not introduce any item thicker than this under the booster seat. Check with the booster seat manufacturer's instructions. CHILD SAFETY LOCKS

WARNING

You cannot open the rear doors from inside if you have put the child safety locks on.

Left-Hand Side Turn counterclockwise to lock and clockwise to unlock.

25

Fiesta (CCT) Vehicles Built From: 01-04-2013, Vehicles Built Up To: 31-12-2013

E156821Safety Belts

WARNINGS

When possible, all children 12 years old and under should be properly restrained in a rear seating position.

Failure to follow this could seriously increase the risk of injury or death.

Safety belts and seats can become hot in a vehicle that has been closed up in sunny weather; they could burn

a small child. Check seat covers and buckles before you place a child anywhere near them.

Front and rear seat occupants, including pregnant women, should wear safety belts for optimum

protection in an accident.

All seating positions in your vehicle have lap and shoulder safety belts. All occupants of the vehicle should always properly wear their safety belts, even when an airbag supplemental restraint system is provided. The safety belt system consists of: lap and shoulder safety belts. • shoulder safety belt with automatic • locking mode, (except driver safety belt). height adjuster at the front outboard seating positions. safety belt pretensioner at the front outboard seating positions. belt tension sensor at the front outboard passenger seating position.

•

•

•

•

Safety belt warning light and chime.

PRINCIPLE OF OPERATION

WARNINGS

Always drive and ride with your seat back upright and the lap belt snug and low across the hips. To reduce the risk of injury, make sure children sit where they can be properly restrained. Never let a passenger hold a child on his or her lap while your vehicle is moving. The passenger cannot

protect the child from injury in a crash.

All occupants of your vehicle, including the driver, should always properly wear their safety belts, even

when an airbag supplemental restraint system is provided. Failure to properly wear your safety belt could seriously increase the risk of injury or death.

It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a crash, people riding in

these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts. Be sure everyone in your vehicle is in a seat and using a safety belt properly.

In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a safety

belt.

Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that are designed to be used as a pair. 1) Use the shoulder belt on the outside shoulder only. Never wear the shoulder belt under the arm. 2) Never swing the safety belt around your neck over the inside shoulder. 3) Never use a single belt for more than one person.

26

Fiesta (CCT) Vehicles Built From: 01-04-2013, Vehicles Built Up To: 31-12-2013

Safety Belts

• Crash sensors and monitoring system

with readiness indicator.

The safety belt pretensioners at the front seating positions are designed to tighten the safety belts when activated. In frontal and near-frontal crashes, the safety belt pretensioners may be activated alone or, if the crash is of sufficient severity, together with the front airbags. The pretensioners may also activate when a side curtain airbag is deployed. FASTENING THE SAFETY BELTS The front outboard and rear safety restraints in the vehicle are combination lap and shoulder belts.

2. To unfasten, press the release button

and remove the tongue from the buckle.

1.

Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle.

When in use, the rear safety belts should be placed in the belt guides on the outboard seat backs. Restraint of Pregnant Women

WARNING

Always ride and drive with your seat back upright and the safety belt properly fastened. The lap portion of

the safety belt should fit snug and be positioned low across the hips. The shoulder portion of the safety belt should be positioned across the chest. Pregnant women should also follow this practice. See the following figure.

27

Fiesta (CCT) Vehicles Built From: 01-04-2013, Vehicles Built Up To: 31-12-2013

E142587E142588E142589Safety Belts

All safety restraints in the vehicle are combination lap and shoulder belts. The driver safety belt has the first type of locking mode, and the front outboard passenger and rear seat safety belts have both types of locking modes described as follows: Vehicle Sensitive Mode This is the normal retractor mode, which allows free shoulder belt length adjustment to your movements and locking in response to vehicle movement. For example, if the driver brakes suddenly or turns a corner sharply, or the vehicle receives an impact of approximately 5 mph (8 km/h) or more, the combination safety belts will lock to help reduce forward movement of the driver and passengers. In addition, the retractor is designed to lock if the webbing is pulled out too quickly. If this occurs, let the belt retract slightly and pull webbing out again in a slow and controlled manner. Automatic Locking Mode In this mode, the shoulder belt is automatically pre-locked. The belt will still retract to remove any slack in the shoulder belt. The automatic locking mode is not available on the driver safety belt. When to Use the Automatic Locking Mode This mode should be used any time a child safety seat, except a booster, is installed in passenger front or rear seating positions. Children 12 years old and under should be properly restrained in a rear seating position whenever possible. See Child Safety (page 14).

Pregnant women should always wear their safety belt. The lap belt portion of a combination lap and shoulder belt should be positioned low across the hips below the belly and worn as tight as comfort will allow. The shoulder belt should be positioned to cross the middle of the shoulder and the center of the chest. Safety Belt Locking Modes

WARNINGS

After any vehicle crash, the safety belt system at all passenger seating positions must be checked by an

authorized dealer to verify that the automatic locking retractor feature for child seats is still functioning properly. In addition, all safety belts should be checked for proper function.

Belt and retractor assembly must be replaced if the safety belt assembly automatic locking retractor feature

or any other safety belt function is not operating properly when checked by an authorized dealer. Failure to replace the belt and retractor assembly could increase the risk of injury in crashes.

28

Fiesta (CCT) Vehicles Built From: 01-04-2013, Vehicles Built Up To: 31-12-2013

E142590Safety Belts

Use only extensions manufactured by the same supplier as the safety belt. Manufacturer identification is located at the end of the webbing on the label. Also, use the safety belt extension only if the safety belt is too short for you when fully extended. SAFETY BELT HEIGHT ADJUSTMENT

WARNING

Position the safety belt height adjuster so that the belt rests across the middle of your shoulder. Failure

to adjust the safety belt properly could reduce the effectiveness of the safety belt and increase the risk of injury in a crash.

Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder.

To adjust the shoulder belt height: 1. Pull the button and slide the height

adjuster up or down.

2. Release the button and pull down on the height adjuster to make sure it is locked in place.

How to Use the Automatic Locking Mode

1. Buckle the combination lap and

shoulder belt.

2. Grasp the shoulder portion and pull

downward until the entire belt is pulled out.

Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode. How to Disengage the Automatic Locking Mode Unbuckle the combination lap and shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive (emergency) locking mode. Safety Belt Extension Assembly

WARNING

Do not use extensions to change the fit of the shoulder belt across the torso.

If the safety belt is too short when fully extended, a safety belt extension assembly can be obtained from an authorized dealer.

29

Fiesta (CCT) Vehicles Built From: 01-04-2013, Vehicles Built Up To: 31-12-2013

E142591E145664Safety Belts

SAFETY BELT WARNING LAMP AND INDICATOR CHIME (IF EQUIPPED)

This lamp illuminates and an audible warning will sound if the driver's safety belt has not been

fastened when the vehicle's ignition is turned on.

Conditions of operation

If...

Then...

The driver's safety belt is not buckled

before the ignition switch is turned to the

on position...

The driver's safety belt is buckled while the

indicator light is illuminated and the

warning chime is sounding...

The safety belt warning light illuminates 1- 2 minutes and the warning chime sounds

4-8 seconds.

The safety belt warning light and warning

chime turn off.

The driver's safety belt is buckled before the ignition switch is turned to the on posi-

tion...

The safety belt warning light and indicator

chime remain off.

SAFETY BELT MINDER (IF EQUIPPED) Belt-Minder® This feature supplements the safety belt warning function by providing additional reminders by intermittently sounding a chime and illuminating the safety belt warning light when the driver's or front passenger's seat is occupied and the safety belt is unbuckled.

The system uses information from the front passenger sensing system to determine if a front seat passenger is present and therefore potentially in need of a warning. To avoid activating the Belt-Minder feature for objects placed in the front passenger seat, warnings will only be given to front seat occupants as determined by the front passenger sensing system. If the Belt-Minder warnings have expired (warnings for about five minutes) for one occupant (driver or front passenger), the other occupant can still activate the Belt-Minder feature.

30

Fiesta (CCT) Vehicles Built From: 01-04-2013, Vehicles Built Up To: 31-12-2013

Safety Belts

If...

Then...

The Belt-Minder feature will not activate.

The Belt-Minder feature is activated - the safety belt warning light illuminates and the warning chime sounds for six seconds every 25 seconds, repeating for about five

minutes or until the safety belts are

buckled.

The Belt-Minder feature is activated - the safety belt warning light illuminates and the warning chime sounds for six seconds every 25 seconds, repeating for about five

minutes or until the safety belts are

buckled.

The system can be deactivated or activated by performing the following procedure: Before following the procedure, make sure that: • •

the parking brake is set the transmission selector lever is in position P (automatic transmission) or N (manual transmission) the ignition is off the driver and front passenger safety belts are unbuckled.

• •

1. Turn the ignition on. Do not start the

vehicle.

2. Wait until the safety belt warning light

turns off (about one minute). After Step 2, wait an additional five seconds before proceeding with Step 3. Once Step 3 is started, the procedure must be completed within 30 seconds.

The driver's and front passenger's safety belts are buckled before the ignition switch is turned to the on position or less than 1-2
minutes have elapsed since the ignition

switch has been turned to on...

The driver's or front passenger's safety belt is not buckled when the vehicle has reached at least 6 mph (9.7 km/h) and 1-2 minutes have elapsed since the ignition switch has

been turned to on...

The driver's or front passenger's safety belt becomes unbuckled for about one minute while the vehicle is traveling at least 6 mph (9.7 km/h) and more than 1-2 minutes have elapsed since the ignition switch has been

turned to on...

Deactivating and Activating the Belt-Minder Feature

WARNING

While the system allows you to deactivate it, this system is designed to improve your chances of being safely belted and surviving an accident. We recommend you leave the system activated for yourself and others who may use the vehicle. To reduce the risk of injury, do not deactivate or activate the system while driving the vehicle.

Note: The driver and front passenger warning are deactivated and activated independently. When deactivating or activating one seating position, do not buckle the other position as this will terminate the process. Read Steps 1 - 4 thoroughly before proceeding with the programming procedure.

31

Fiesta (CCT) Vehicles Built From: 01-04-2013, Vehicles Built Up To: 31-12-2013

Safety Belts

Ford Motor Company recommends that all safety belt assemblies in use in vehicles involved in a crash be replaced. However, if the crash was minor and an authorized dealer finds that the belts do not show damage and continue to operate properly, they do not need to be replaced. Safety belt assemblies not in use during a crash should also be inspected and replaced if either damage or improper operation is noted. Properly care for safety belts.

3. For the seating position being disabled,

buckle then unbuckle the safety belt three times at a moderate speed, ending in the unbuckled state. After Step 3, the safety belt warning light will turn on.

4. While the safety belt warning light is

on, buckle and then unbuckle the safety belt. After Step 4, the safety belt warning light will flash for confirmation. This will disable the feature for that seating position if it is currently enabled. This will enable the feature for that seating position if it is currently disabled.

•

•

CHILD RESTRAINT AND SAFETY BELT MAINTENANCE Inspect the vehicle safety belts and child safety seat systems periodically to make sure they work properly and are not damaged. Inspect the vehicle and child seat safety belts to make sure there are no nicks, tears or cuts. Replace if necessary. All vehicle safety belt assemblies, including retractors, buckles, front safety belt buckle assemblies, buckle support assemblies (slide bar-if equipped), shoulder belt height adjusters (if equipped), shoulder belt guide on seat back (if equipped), child safety seat LATCH and tether anchors, and attaching hardware, should be inspected after a crash. Read the child restraint manufacturer's instructions for additional inspection and maintenance information specific to the child restraint.

32

Fiesta (CCT) Vehicles Built From: 01-04-2013, Vehicles Built Up To: 31-12-2013

Personal Safety System™

module. During a crash, the restraints control module may activate the safety belt pretensioners and may activate either one or both stages of the dual-stage airbag supplemental restraints based on crash severity and occupant conditions.

The Personal Safety System provides an improved overall level of frontal crash protection to front seat occupants and is designed to help further reduce the risk of airbag-related injuries. The system is able to analyze different occupant conditions and crash severity before activating the appropriate safety devices to help better protect a range of occupants in a variety of frontal crash situations. Your vehicle's Personal Safety System consists of: • Driver and passenger dual-stage airbag

supplemental restraints. Front outboard safety belts with pretensioners, energy management retractors (first row only), and safety belt usage sensors.

• Driver’s seat position sensor. • • Passenger airbag off and on indicator

Front passenger sensing system.

lamp. Front crash severity sensors.

• • Restraints control module with impact

and safing sensors.

• Restraint system warning light and

backup tone. The electrical wiring for the airbags, crash sensor(s), safety belt pretensioners, front safety belt usage sensors, driver seat position sensor, front passenger sensing system, and indicator lights.

•

•

How Does the Personal Safety System Work? The Personal Safety System can adapt the deployment strategy of your vehicle’s safety devices according to crash severity and occupant conditions. A collection of crash and occupant sensors provides information to the restraints control

33

Fiesta (CCT) Vehicles Built From: 01-04-2013, Vehicles Built Up To: 31-12-2013

Supplementary Restraints System

The airbags are a supplemental restraint system and are designed to work with the safety belts to help protect the driver and right front passenger from certain upper body injuries. Airbags do not inflate slowly; there is a risk of injury from a deploying airbag. Note: You will hear a loud bang and see a cloud of harmless powdery residue if an airbag deploys. This is normal. The airbags inflate and deflate rapidly upon activation. After airbag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (for example, baking soda) that result from the combustion process that inflates the airbag. Small amounts of sodium hydroxide may be present which may irritate the skin and eyes, but none of the residue is toxic. While the system is designed to help reduce serious injuries, contact with a deploying airbag may also cause abrasions or swelling. Temporary hearing loss is also a possibility as a result of the noise associated with a deploying airbag. Because airbags must inflate rapidly and with considerable force, there is the risk of death or serious injuries such as fractures, facial and eye injuries or internal injuries, particularly to occupants who are not properly restrained or are otherwise out of position at the time of airbag deployment. Thus, it is extremely important that occupants be properly restrained as far away from the airbag module as possible while maintaining vehicle control. Routine maintenance of the airbags is not required.

PRINCIPLE OF OPERATION

WARNINGS

Airbags do not inflate slowly or gently, and the risk of injury from a deploying airbag is the greatest close

to the trim covering the airbag module.

All occupants of your vehicle, including the driver, should always properly wear their safety belts, even

when an airbag supplemental restraint system is provided. Failure to properly wear your safety belt could seriously increase the risk of injury or death.

Always transport children 12 years old and under in the back seat and always properly use appropriate

child restraints. Failure to follow this could seriously increase the risk of injury or death. Never place your arm over the airbag module as a deploying airbag can result in serious arm fractures or

other injuries.

Airbags can kill or injure a child in a child seat. Never place a rear-facing child seat in front of an active airbag. If you must use a forward-facing child seat in the front seat, move the seat all the way back.

Do not attempt to service, repair, or modify the airbag supplemental restraint systems or its fuses as you could be seriously injured or killed. Contact your authorized dealer as soon as possible. Several airbag system components get hot after inflation. Do not touch them after inflation as this may result

in serious injury.

If the airbag has deployed, the airbag will not function again and must be replaced immediately. If the airbag is not replaced, the unrepaired area will increase the risk of injury in a collision.

34

Fiesta (CCT) Vehicles Built From: 01-04-2013, Vehicles Built Up To: 31-12-2013

Supplementary Restraints System

Proper Driver and Front Passenger Seating Adjustment WARNING

National Highway Traffic Safety Administration (NHTSA) recommends a minimum distance

of at least 10 inches (25 centimeters) between an occupant’s chest and the driver airbag module.

To properly position yourself away from the airbag: • Move your seat to the rear as far as you

can while still reaching the pedals comfortably.

• Recline the seat slightly (one or two degrees) from the upright position. After all occupants have adjusted their seats and put on safety belts, it is very important that they continue to sit properly. A properly seated occupant sits upright, leaning against the seat back, and centered on the seat cushion, with their feet comfortably extended on the floor. Sitting improperly can increase the chance of injury in a crash event. For example, if an occupant slouches, lies down, turns sideways, sits forward, leans forward or sideways, or puts one or both feet up, the chance of injury during a crash is greatly increased. Children and Airbags WARNING

Airbags can kill or injure a child in a child seat. Never place a rear-facing child seat in front of an active airbag. If you must use a forward-facing child seat in the front seat, move the seat upon which the child seat is installed all the way back.

DRIVER AND PASSENGER AIRBAGS

WARNINGS

Never place your arm or any objects over an airbag module. Placing your arm over a deploying airbag can result in serious arm fractures or other injuries. Objects placed on or over the airbag inflation area may cause those objects to be propelled by the airbag into your face and torso causing serious injury. Airbags can kill or injure a child in a child seat. Never place a rear-facing child seat in front of an active airbag. If you must use a forward-facing child seat in the front seat, move the seat upon which the child seat is installed all the way back.

The driver and front passenger airbags will deploy during significant frontal and near frontal crashes. The driver and passenger front airbag system consists of: • •

driver and passenger airbag modules. front passenger sensing system.

· crash sensors and monitoring system with readiness indicator. See Crash Sensors and Airbag

Indicator (page 41).

35

Fiesta (CCT) Vehicles Built From: 01-04-2013, Vehicles Built Up To: 31-12-2013

E151127Supplementary Restraints System

WARNINGS

and the center console. Check the passenger airbag off or pass airbag off indicator lamp for proper airbag status. Failure to follow these instructions may interfere with the front passenger seat sensing system.

Any alteration or modification to the front passenger seat may affect the performance of the front passenger

sensing system.

This system works with sensors that are part of the front passenger’s seat and safety belt to detect the presence of a properly-seated occupant and determine if the front passenger’s frontal airbag should be enabled (may inflate) or not.

The front passenger sensing system uses a pass airbag off indicator which will illuminate and stay lit to remind you that the front passenger frontal airbag is disabled. The indicator lamp is located at the top center of the instrument panel. Note: When the ignition is first tuned on, the indicator lamp will illuminate for a short period of time to confirm it is functional. The front passenger sensing system is designed to disable (will not inflate) the front passenger's frontal airbag when a rear facing infant seat, a forward-facing child restraint, or a booster seat is detected. Even with this technology,

Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position. Failure to follow these instructions may increase the risk of injury in a crash. FRONT PASSENGER SENSING SYSTEM

WARNINGS

Even with Advanced Restraints Systems, children 12 and under should be properly restrained in a

rear seating position. Failure to follow this could seriously increase the risk of injury or death.

Sitting improperly out of position or with the seat back reclined too far can take off weight from the seat

cushion and affect the decision of the front passenger sensing system, resulting in serious injury or death in a crash.

To reduce the risk of possible serious injury: Do not stow objects in seat back map pocket or hang objects off seat back if a child is in the front passenger seat. Do not place objects underneath the front passenger seat or between the seat

36

Fiesta (CCT) Vehicles Built From: 01-04-2013, Vehicles Built Up To: 31-12-2013

E142846E157152Supplementary Restraints System

parents are STRONGLY encouraged to always properly restrain children in the rear seat. The sensor also turns off the passenger front airbag and seat-mounted side airbag when the passenger seat is empty. • When the front passenger sensing

system disables (will not inflate) the front passenger frontal airbag, the indicator lamp will illuminate and stay lit to remind you that the front passenger frontal airbag is disabled. If the child restraint has been installed and the indicator lamp is not lit, then turn the vehicle off, remove the child restraint from the vehicle and reinstall the restraint following the child restraint manufacturer's instructions.

•

The front passenger sensing system is designed to enable (may inflate) the front passenger's frontal airbag anytime the system senses that a person of adult size is sitting properly in the front passenger seat.

•

• When the front passenger sensing

system enables the front passenger frontal airbag (may inflate), the indicator lamp will be unlit and stay unlit.

If a person of adult size is sitting in the front passenger’s seat, but the airbag off indicator lamp is lit, it is possible that the person isn’t sitting properly in the seat. If this happens: •

Turn the vehicle off and ask the person to place the seat back in the full upright position.

• Have the person sit upright in the seat, centered on the seat cushion, with the person’s legs comfortably extended.

• Restart the vehicle and have the person

remain in this position for about two minutes. This will allow the system to detect that person and enable the passenger’s frontal airbag. If the indicator lamp remains lit even after this, the person should be advised to ride in the rear seat.

Occupant

Empty Child Adult

Passenger airbag OFF indic-

ator Unlit Lit Unlit

Passenger airbag

Disabled Disabled Enabled

Note: When the passenger airbag off light is illuminated, the passenger (seat mounted) side airbag may be disabled to avoid the risk of airbag deployment injuries. After all occupants have adjusted their seats and put on safety belts, it is very important that they continue to sit properly. A properly seated occupant sits upright, leaning against the seat back, and centered on the seat cushion, with their feet comfortably extended on the floor. Sitting improperly can increase the chance

of injury in a crash event. For example, if an occupant slouches, lies down, turns sideways, sits forward, leans forward or sideways, or puts one or both feet up, the chance of injury during a crash is greatly increased. If you think that the status of the passenger airbag off indicator lamp is incorrect, check for the following:

37

Fiesta (CCT) Vehicles Built From: 01-04-2013, Vehicles Built Up To: 31-12-2013

Supplementary Restraints System

• Wait at least two minutes and verify that the airbag readiness light is no longer illuminated. If the airbag readiness light remains illuminated, this may or may not be a problem due to the front passenger sensing system.

•

Do not attempt to repair or service the system. Take your vehicle immediately to an authorized dealer. If it is necessary to modify an advanced front airbag system to accommodate a person with disabilities, contact the Ford Customer Relationship Center. See Getting the Services You Need (page 160). SIDE AIRBAGS

WARNINGS

Do not place objects or mount equipment on or near the airbag cover, on the side of the seatbacks (of the front seats), or in front seat areas that may come into contact with a deploying airbag. Failure to follow these instructions may increase the risk of personal injury in the event of a crash.

Do not use accessory seat covers. The use of accessory seat covers may prevent the deployment of the side airbags and increase the risk of injury in an accident.

Do not lean your head on the door. The side airbag could injure you as it deploys from the side of the

seatback.

Do not attempt to service, repair, or modify the airbag, its fuses or the seat cover on a seat containing an

airbag as you could be seriously injured or killed. Contact your authorized dealer as soon as possible.

• Objects lodged underneath the seat • Objects between the seat cushion and

the center console

• Objects hanging off the seat back • Objects stowed in the seat back map

pocket

• Objects placed on the occupant's lap • Cargo interference with the seat • Other passengers pushing or pulling on

the seat

• Rear passenger feet and knees resting

or pushing on the seat

The conditions listed above may cause the weight of a properly seated occupant to be incorrectly interpreted by the front passenger sensing system. The person in the front passenger seat may appear heavier or lighter due to the conditions described in the list above.

Make sure the front passenger sensing system is operating properly. See Crash Sensors

and Airbag Indicator (page 41). If the airbag readiness light is lit, do the following: The driver and adult passengers should check for objects lodged underneath the front passenger seat, or cargo interfering with the seat. If there are lodged objects, or cargo is interfering with the seat, take the following steps to remove the obstruction: • Pull the vehicle over. • Turn the vehicle off. • Driver and adult passengers should

check for any objects lodged underneath the front passenger seat or cargo interfering with the seat.

• Remove the obstruction(s) (if found). • Restart the vehicle.

38

Fiesta (CCT) Vehicles Built From: 01-04-2013, Vehicles Built Up To: 31-12-2013

Supplementary Restraints System

The design and development of the side airbag system included recommended testing procedures that were developed by a group of automotive safety experts known as the Side Airbag Technical Working Group. These recommended testing procedures help reduce the risk of injuries related to the deployment of side airbags. DRIVER KNEE AIRBAG (IF EQUIPPED)

A driver’s knee airbag is located under or within the instrument panel. During a crash, the restraints control module may activate the driver’s knee airbag based on crash severity and occupant conditions. Under certain crash and occupant conditions, the driver’s knee airbag may deploy but the driver’s front airbag may not activate. As with front and side airbags, it is important to be properly seated and restrained to reduce the risk of death or serious injury.

Make sure the knee airbag is operating properly. See Crash Sensors and Airbag Indicator

(page 41).

SIDE CURTAIN AIRBAGS

WARNINGS

Do not place objects or mount equipment on or near the headliner at the siderail that may come into

contact with a deploying side curtain airbag. Failure to follow these instructions may increase the risk of personal injury in the event of a crash.

Do not lean your head on the door. The side curtain airbag could injure you as it deploys from the headliner.

WARNINGS

If the side airbag has deployed, the airbag will not function again. The side airbag system (including the

seat) must be inspected and serviced by an authorized dealer. If the airbag is not replaced, the unrepaired area will increase the risk of injury in a crash.

The side airbags are located on the outboard side of the seatbacks of the front seats. In certain sideways crashes, the airbag on the side affected by the crash will be inflated. The airbag was designed to inflate between the door panel and occupant to further enhance the protection provided occupants in side impact crashes.

The system consists of the following: • A label or embossed side panel

indicating that side airbags are fitted to your vehicle. Side airbags located inside the driver and front passenger seatbacks. Front passenger sensing system.

•

•

·Crash sensors and monitoring system with readiness indicator. See Crash Sensors and Airbag

Indicator (page 41). Note: The passenger sensing system will deactivate the passenger seat-mounted side airbag if it detects an empty passenger seat.

39

Fiesta (CCT) Vehicles Built From: 01-04-2013, Vehicles Built Up To: 31-12-2013

E152533Supplementary Restraints System

WARNINGS

Do not attempt to service, repair, or modify the side curtain airbags, its fuses, the A, B, or C pillar trim, or the

headliner on a vehicle containing side curtain airbags. Contact your authorized dealer as soon as possible.

All occupants of the vehicle including the driver should always wear their safety belts even when an airbag supplemental restraint system and side curtain airbag is provided.

To reduce risk of injury, do not obstruct or place objects in the deployment path of the side curtain

airbag.

If the side curtain airbags have deployed, the side curtain airbags will not function again. The side

curtain airbags (including the A, B and C pillar trim and headliner) must be inspected and serviced by an authorized dealer. If the side curtain airbag is not replaced, the unrepaired area will increase the risk of injury in a crash.

The side curtain airbags will deploy during significant side crashes. The side curtain airbags are mounted to the roof side-rail sheet metal, behind the headliner, above each row of seats. The side curtain airbags are designed to inflate between the side window area and occupants to further enhance protection provided in side impact crashes. The system consists of the following:

•

Side curtain airbags located above the trim panels over the front and rear side windows identified by a label or wording on the headliner or roof-pillar trim.

• A flexible headliner which opens above the side doors to allow side air curtain deployment.

Crash sensors and monitoring system with readiness indicator. See Crash Sensors and Airbag

Indicator (page 41). Children 12 years old and under should always be properly restrained in the back seats. The side curtain airbags will not interfere with children restrained using a properly installed child or booster seat because it is designed to inflate downward from the headliner above the doors along the side window opening. The design and development of the side curtain airbags included recommended testing procedures that were developed by a group of automotive safety experts known as the Side Airbag Technical Working Group. These recommended testing procedures help reduce the risk of injuries related to the deployment of side curtain airbags.

40

Fiesta (CCT) Vehicles Built From: 01-04-2013, Vehicles Built Up To: 31-12-2013

E75004Supplementary Restraints System

CRASH SENSORS AND AIRBAG INDICATOR WARNING

Modifying or adding equipment to the front end of the vehicle (including frame, bumper, front end body

structure and tow hooks) may affect the performance of the airbag system, increasing the risk of injury. Do not modify the front end of the vehicle.

The vehicle has a collection of crash and occupant sensors which provide information to the restraints control module which deploys (activates) the front safety belt pretensioners, driver airbag, passenger airbag, knee airbag(s), seat mounted side airbags, and the side curtain airbags. Based on the type of crash (frontal impact or side impact), the restraints control module will deploy the appropriate safety devices. The restraints control module also monitors the readiness of the above safety devices plus the crash and occupant sensors. The readiness of the safety system is indicated by a warning indicator light in the instrument cluster or by a backup tone if the warning light is not working. Routine maintenance of the airbag is not required. A difficulty with the system is indicated by one or more of the following:

The readiness light will not illuminate immediately after the ignition is turned on.

•

The readiness light will either flash or stay lit.

• A series of five beeps will be heard. The

tone pattern will repeat periodically until the problem, the light or both are repaired.

Fiesta (CCT) Vehicles Built From: 01-04-2013, Vehicles Built Up To: 31-12-2013

If any of these things happen, even intermittently, have the supplemental restraint system serviced at an authorized dealer immediately. Unless serviced, the system may not function properly in the event of a crash. The safety belt pretensioners and the front airbag supplemental restraint system are designed to activate when the vehicle sustains longitudinal deceleration sufficient to cause the restraints control module to deploy a safety device. The fact that the safety belt pretensioners or front airbags did not activate for both front seat occupants in a crash does not mean that something is wrong with the system. Rather, it means the restraints control module determined the accident conditions (crash severity, belt usage) were not appropriate to activate these safety devices. •

The design of the front airbags is to activate only in frontal and near-frontal crashes (not rollovers, side impacts or rear impacts) unless the crash causes sufficient longitudinal deceleration. The design of the safety belt pretensioners is to activate in frontal and near-frontal crashes, and may also activate when a side curtain deploys. The driver's knee airbag may deploy based on crash severity and occupant conditions.

•

•

41

Supplementary Restraints System

•

•

The design of the side airbags is to inflate in certain side impact crashes. Side airbags may activate in other types of crashes if your vehicle experiences sufficient sideways motion or deformation. The design of the Safety Canopy is to inflate in certain side impact crashes or rollover events. The Safety Canopy may activate in other types of crashes if your vehicle experiences sufficient sideways motion or deformation, or a certain likelihood of rollover.

AIRBAG DISPOSAL Contact your authorized dealer as soon as possible. Airbags must be disposed of by qualified personnel.

42

Fiesta (CCT) Vehicles Built From: 01-04-2013, Vehicles Built Up To: 31-12-2013

Keys and Remote Controls

•

Intelligent Access (If Equipped) The system uses a radio frequency signal to communicate with your vehicle and authorize your vehicle to unlock when one of the following conditions are met: You touch the inside of the front • exterior door handle. You press the luggage compartment button. • You press a button on the transmitter. If excessive radio frequency interference is present in the area or if the transmitter battery is low, you may need to mechanically unlock your door. You can use the mechanical key blade in your intelligent access key to open the driver door in this situation. See Remote Control (page 43). REMOTE CONTROL Integrated Keyhead Transmitter (If Equipped)

Use the key blade to start your vehicle and unlock or lock the driver door from outside your vehicle. The transmitter portion functions as the remote control.

GENERAL INFORMATION ON RADIO FREQUENCIES This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Note: Changes or modifications not expressively approved by the party responsible for compliance could void the user's authority to operate the equipment. The term IC before the radio certification number only signifies that Industry Canada technical specifications were met. The typical operating range for your transmitter is approximately 33 feet (10
meters). Vehicles with the remote start feature will have a greater range. One of the following could cause a decrease in operating range: • weather conditions nearby radio towers • structures around the vehicle • other vehicles parked next to your • vehicle

The radio frequency used by your remote control can also be used by other short distance radio transmissions, for example amateur radios, medical equipment, wireless headphones, remote controls and alarm systems. If the frequencies are jammed, you will not be able to use your remote control. You can lock and unlock the doors with the key. Note: Make sure to lock your vehicle before leaving it unattended. Note: If you are in range, the remote control will operate if you press any button unintentionally.

43

Fiesta (CCT) Vehicles Built From: 01-04-2013, Vehicles Built Up To: 31-12-2013

E142585Keys and Remote Controls

Reprogramming the Unlocking Function Note: When you press the unlock button either all the doors are unlocked or only the driver’s door and the liftgate are unlocked. Pressing the unlock button again unlocks all the doors. You can reprogram the unlocking function using the remote control so that only the driver's door is unlocked. This will enable two-stage unlocking. Press and hold the unlock and lock buttons on the remote control simultaneously for at least four seconds with the ignition off. The direction indicators will flash twice to confirm the change. To return to the original unlocking function, repeat the process. Replacing the Battery Note: Refer to local regulations when disposing of transmitter batteries. Note: Do not wipe off any grease on the battery terminals or on the back surface of the circuit board. Note: Replacing the battery will not delete the transmitter from the vehicle. The transmitter should operate normally. The remote control uses one coin-type three-volt lithium battery CR2032 or equivalent.

Note: Your vehicle’s keys came with a security label that provides important vehicle key cut information. Keep the label in a safe place for future reference. Intelligent Access Transmitter (If Equipped) Your intelligent access keys operate the power locks. The key must be in your vehicle to activate the push button start system. The intelligent access key also contains a removable mechanical key blade that you can use to unlock the driver door.

Note: Your vehicle’s back-up keys came with a security tag that provides important vehicle key cut information. Keep the tag in a safe place for future reference.

44

Fiesta (CCT) Vehicles Built From: 01-04-2013, Vehicles Built Up To: 31-12-2013

E162601E87964211Keys and Remote Controls

Vehicles Without Intelligent Access

1.

Insert a screwdriver into the recess on the back of the key and remove the key blade.

Note: Do not touch the battery contacts or the printed circuit board with the screwdriver. 3. Carefully pry out the battery with the

screwdriver. Install a new battery (3V CR 2032) with the + facing upward.

4.

5. Assemble the two halves of the remote

control. Install the key blade.

6. Integrated Keyhead Transmitter

2. Release the retaining clips with the screwdriver and separate the two halves of the remote control.

1. Twist a thin coin in the slot of the

transmitter near the key ring to remove the battery cover.

2. Remove the old battery.

45

Fiesta (CCT) Vehicles Built From: 01-04-2013, Vehicles Built Up To: 31-12-2013

1E126152E1261532E1262813E138619Keys and Remote Controls

3.

Insert the new battery. Refer to the instructions inside the transmitter for the correct orientation of the battery. Press the battery down to make sure it is fully in the housing.

4. Snap the battery cover back onto the

transmitter.

Intelligent Access Transmitter

3. Twist the screwdriver in the position

shown to start separating the two halves of the remote control.

4. Twist the screwdriver in the position shown to separate the two halves of the remote control.

1. Press and hold the buttons on the

edges to release the cover. Carefully remove the cover.

2. Remove the key blade.

46

Fiesta (CCT) Vehicles Built From: 01-04-2013, Vehicles Built Up To: 31-12-2013

E138620E87964211E1053623E1191904E1258605Keys and Remote Controls

Note: Do not touch the battery contacts or the printed circuit board with the screwdriver. 5. Carefully remove the battery with the

screwdriver. Install a new battery (3V CR 2032) with the + facing downward.

6.

7. Assemble the two halves of the remote

control. Install the key blade.

8. Car Finder

Press the button twice within three seconds. The horn will sound and the turn signals will flash. We recommend you use this method to locate your vehicle, rather than using the panic alarm. Note: If locking was not successful or if any door or the liftgate is open, or if the hood is open on vehicles with a perimeter alarm or remote start, the horn will sound twice and the lamps will not flash. Sounding a Panic Alarm (If Equipped) Note: The panic alarm will only operate when the ignition is off.

Press the button to activate the alarm. Press the button again or turn the ignition on to deactivate.

REPLACING A LOST KEY OR REMOTE CONTROL Replacement or additional keys or remote controls can be purchased from an authorized dealer. Your dealer can program the remote controls for your vehicle or you may be able to program them yourself. See Remote Control (page 43). To re-program the passive anti-theft system see an authorized dealer.

47

Fiesta (CCT) Vehicles Built From: 01-04-2013, Vehicles Built Up To: 31-12-2013

E138623E138624MyKey™ (If Equipped)

• Driver assist features, if equipped on

your vehicle, are forced on: parking aid, blind spot information system (BLIS) with cross traffic alert, lane departure warning and forward collision warning system. Satellite radio adult content restrictions.

•

Configurable Settings With an admin key, you can configure certain MyKey settings when you first create a MyKey and before you recycle the key or restart the vehicle. You can also change the settings afterward with an admin key: • Vehicle speed limits can be set.

Warnings will be shown in the display followed by an audible tone when your vehicle reaches the set speed. You cannot override the set speed by fully depressing the accelerator pedal.

• Vehicle speed minders of 45, 55 or 65
mph (75, 90 or 105 km/h). Once you select a speed it will be shown in the display followed by an audible tone when the set vehicle speed is exceeded.

• Audio system maximum volume of

45%. A message will be shown in the display when you attempt to exceed the limited volume. Also, the speed sensitive compensated volume (automatic volume control) feature will be disabled.

• Always on setting. When this is

selected you will not be able to disable AdvanceTrac, 911 Assist or the do not disturb feature (if your vehicle is equipped with these features).

CREATING A MYKEY Use the information display to create a MyKey.

•

PRINCIPLE OF OPERATION MyKey allows you to program keys with restricted driving modes to promote good driving habits. All but one of the keys programmed to the vehicle can be activated with these restricted modes. Any keys that have not been programmed are referred to as administrator keys or admin keys. These can be used to: • Create a MyKey • Program configurable MyKey settings • Clear all MyKey features When you have programmed a MyKey, you can access the following information using the information display: • How many admin keys and MyKeys are

programmed to your vehicle. The total distance your vehicle has traveled using any MyKey.

Note: All MyKeys are programmed to the same settings. You cannot program them individually. If a MyKey and an admin key are present, your vehicle will recognize the admin key only. Note: For vehicles with intelligent access key (push button start) keyless start, when both a MyKey and an admin intelligent access key (fob) are present, the admin fob will be recognized by the vehicle to start the engine. Non-configurable Settings The following settings cannot be changed by an admin key user: •

Belt-minder. You cannot disable this feature. The audio system will mute when the front seat occupants' safety belts are not fastened. Early low fuel. The low-fuel warning activates earlier, giving the MyKey user more time to refuel.

•

48

Fiesta (CCT) Vehicles Built From: 01-04-2013, Vehicles Built Up To: 31-12-2013

MyKey™ (If Equipped)

CLEARING ALL MYKEYS You can clear all MyKeys within the same key cycle as you created the MyKey. If you switch your ignition off, however, you will need to use an admin key to clear your MyKeys. Note: When you clear your MyKeys, you remove all restrictions and return all MyKeys to their original admin key status at once. To clear all MyKeys of all MyKey settings, use the information display to do the following: 1. Access the main menu and select

Settings, then MyKey.

2. Scroll to Clear MyKey and press the

OK button.

3. Hold the OK button until ALL MYKEYS CLEARED displays.

CHECKING MYKEY SYSTEM STATUS You can find information about your programmed MyKeys by using the information display. MyKey Distance Tracks the distance when drivers use a MyKey. The only way to delete the accumulated distance is by using an admin key to clear your MyKey. If the distance does not accumulate as expected, then the intended user is not using the MyKey, or an admin key user recently cleared and then recreated a MyKey. Number of MyKeys Indicates the number of MyKeys programmed to your vehicle. Use this feature to detect how many MyKeys you have for your vehicle and determine when a MyKey has been deleted.

1.

Insert the key you want to program into the ignition or, if the vehicle has push button start, hold the intelligent access key or fob next to the steering column. 2. Using the information display controls, access the main menu and select Settings, then MyKey by pressing OK or the right arrow button.

3. Press OK to select Create MyKey. 4. When prompted, hold the OK button until you see a message informing you to label this key as a MyKey. The key will be restricted at the next start.

MyKey is successfully created. Make sure you label it so you can distinguish it from the admin keys. You can program configurable settings for the key(s). Refer to Programming or Changing Configurable Settings. Programming or Changing Configurable Settings Use the information display to access your configurable MyKey settings. 1. Switch the ignition on using an admin

key. If the vehicle has push-button start, hold an intelligent access admin key or fob next to the steering column and use the push-button start to switch the ignition on.

2. Access the main menu and select

Settings, then MyKey by pressing OK or the right arrow key.

3. Use the arrow buttons to get to a

configurable feature.

4. Press OK or the right arrow button to

make a selection.

Note: You can clear or change your MyKey settings at any time during the same key cycle as you created the MyKey. If you switch the ignition off, however, you will need to use an admin key to clear your MyKeys.

49

Fiesta (CCT) Vehicles Built From: 01-04-2013, Vehicles Built Up To: 31-12-2013

MyKey™ (If Equipped)

Number of Admin Keys Indicates how many admin keys are programmed to your vehicle. Use this feature to determine how many admin keys you have for your vehicle, and detect if an additional MyKey has been programmed.

MYKEY TROUBLESHOOTING

Condition

I cannot create a MyKey.

I cannot program the configurable settings.

I cannot clear the MyKeys.

I lost the only admin key.

I lost a key.

No MyKey functions with intelligent access key (push-button start).

MyKey distances do not accumulate.

USING MYKEY WITH REMOTE START SYSTEMS MyKey is not compatible with non-Ford-approved aftermarket remote start systems. If you choose to install a remote start system, please see an authorized dealer for a Ford-approved remote start system.

Potential causes

· The key or fob used to start the vehicle does not have admin privileges. · The key or fob used to start the vehicle is the only admin key (there always has to be at least one admin key). · Vehicles with push-button start: The intelligent access key is not in the correct position. The position location is in another chapter. See Keyless Starting (page 113). · SecuriLock passive anti-theft system is disabled or in unlimited mode. · The key or fob used to start the vehicle does not have admin privileges. · No MyKeys have been created. See Creating a MyKey (page 48). · The key or fob used to start the vehicle does not have admin privileges. · No MyKeys are programmed to the vehicle. See Creating a MyKey (page 48). Purchase a new key from an authorized dealer. Program a spare key. See Passive Anti- Theft System (page 60). · An admin key is present at engine start- up. · No MyKeys are programmed to the vehicle. See Creating a MyKey (page 48). · The MyKey user is not using a MyKey.

50

Fiesta (CCT) Vehicles Built From: 01-04-2013, Vehicles Built Up To: 31-12-2013

MyKey™ (If Equipped)

Condition

Potential causes

· An admin key holder cleared the MyKeys and reset the key system.

51

Fiesta (CCT) Vehicles Built From: 01-04-2013, Vehicles Built Up To: 31-12-2013

Locks

Press the button again within three seconds to confirm that all the doors are closed. The doors will lock again, and the direction indicators will flash twice if all the doors and the luggage compartment are closed. Note: If any door or the luggage compartment is not closed, or if the hood is not closed on vehicles that have an anti-theft alarm or remote start, the direction indicators will not flash. Automatic Re-locking The doors will relock automatically if you do not open a door within 45 seconds of unlocking the doors with the remote control. The door locks and the alarm will return to their previous state. Locking and Unlocking the Doors From Inside The power door lock control is located on the instrument panel near the radio.

Press the button to lock and unlock all the doors. The lamp illuminates with the doors

locked. Locking and Unlocking the Doors With the Key Note: Do not leave your keys in your vehicle. Locking With the Key Turn the top of the key toward the front of your vehicle. Unlocking With the Key Turn the top of the key toward the rear of your vehicle.

LOCKING AND UNLOCKING Remote Control The remote control can be used any time your vehicle is not running. Unlocking the Doors Note: You can unlock the driver's door with the key. Use the key when the remote control is not functioning. Note: When you lock your vehicle for several weeks, the remote control will be switched off. Your vehicle must be unlocked and the engine started using the key. Unlocking and starting your vehicle once will enable the remote control. One-Stage Unlocking

Press the button to unlock all the doors.

The direction indicators will flash. Two-Stage Unlocking

Press the button to unlock the driver’s door.

Press the button again within three seconds to unlock all doors. The direction indicators will flash. Reprogramming the Unlocking Function You can reprogram the unlocking function using the remote control to change between one-stage and two-stage unlocking. See Remote Control (page 43). Locking the Doors

Press the button to lock all the doors. The direction indicators will flash twice.

52

Fiesta (CCT) Vehicles Built From: 01-04-2013, Vehicles Built Up To: 31-12-2013

E102566Locks

Unlocking the Doors With the Interior Door Handles You can unlock individual doors by pulling the relevant interior door handle. Pulling the driver's interior door handle will unlock all the doors, if auto unlock has been enabled. Rear Door Unlocking and Opening Pull the interior door release handle twice to unlock and open the rear door. The first pull unlocks the door and the second pull will unlatch the door. Smart Unlocks for Integrated Keyhead Transmitter This feature helps to prevent you from locking yourself out of your vehicle if your key is still in the ignition. When you open one of the front doors and lock your vehicle with the power door lock control, all the doors will lock then unlock if your key is still in the ignition. You can still lock your vehicle with the key in the ignition by pressing the lock button on the transmitter even if the doors are not closed. If both front doors are closed, you can lock your vehicle by any method, regardless of whether the key is in the ignition or not. Smart Unlocks for Intelligent Access Keys (If Equipped) This feature helps to prevent you from unintentionally locking your intelligent access key inside your vehicle’s passenger compartment or rear cargo area.

When you lock your vehicle using the power door lock control (with the door open, vehicle in park and ignition off), your vehicle will search for an intelligent access key in the passenger compartment after you close the door. If your vehicle finds a key, all of the doors will immediately unlock and the horn will chirp, indicating that a key is inside. In order to override the smart unlock feature and intentionally lock the intelligent access key inside your vehicle, you can lock your vehicle after all doors are closed by pressing the lock button on another intelligent access key or touching the locking area on the handle with another intelligent access key in your hand. When you open one of the front doors and lock your vehicle using the power door lock control, all doors will lock then unlock if: • •

the ignition is on, or the ignition is off and the transmission is not in P.

Auto Lock Feature The auto lock feature will lock the doors and liftgate when all of the following conditions have been met: • All doors are closed. • •

The ignition is on. Your vehicle is moving at a speed greater than 12 mph (20 km/h) for more than two seconds.

Enabling or Disabling Auto Lock Note: You cannot disable the auto lock feature in some markets. Note: See an authorized dealer to enable or disable the auto lock feature or carry out the following procedure. Note: You will have 30 seconds to complete the procedure. 1. Switch the ignition on.

53

Fiesta (CCT) Vehicles Built From: 01-04-2013, Vehicles Built Up To: 31-12-2013

Locks

2. Press the power door lock button three

times.

2. Press the power door lock button three

times.

3. Switch the ignition off. 4. Press the power door lock button three

times.

5. Switch the ignition on. The horn will

chirp indicating your vehicle is in programming mode.

6. Press the power door lock button for longer than two seconds and release. The horn will chirp once if disabled or twice (one short and one long chirp) if enabled. After programming the feature, switch the ignition off. The horn will chirp once indicating programming is complete. Emergency Locking With the Key Note: If the child safety locks are on and you pull the interior handle, you will only turn off the emergency locking, not the child safety lock. You can only open the doors using the external door handle. Note: If the doors have been unlocked using this method, the doors must be locked individually until the central locking function has been repaired. Note: When the central locking function fails to operate, lock the doors individually using the key in the position shown.

3. Switch the ignition off. 4. Press the power door lock button three

times.

5. Switch the ignition on. The horn will

chirp indicating your vehicle is in programming mode.

6. Press the power door lock button for

less than one second and release.

The horn will chirp once if disabled or twice (one short and one long chirp) if enabled. After programming the feature, switch the ignition off. The horn will chirp once indicating programming is complete. Auto Unlock Feature The auto unlock feature will unlock all the doors when all of the following conditions have been met: •

The ignition is on, all doors are closed, and your vehicle is moving at a speed greater than 12 mph (20 km/h) for more than two seconds. Your vehicle has come to a stop and you switch the ignition off or to the accessory position. The driver's door is opened within 10
minutes of you switching the ignition off or to the accessory position.

•

•

Note: The doors will not auto unlock if your vehicle has been electronically locked after the ignition is turned off and before the driver's door is opened. Enabling or Disabling Auto Unlock Note: See an authorized dealer to enable or disable the auto unlock feature or carry out the following procedure. Note: You will have 30 seconds to complete the procedure. 1. Switch the ignition on.

54

Fiesta (CCT) Vehicles Built From: 01-04-2013, Vehicles Built Up To: 31-12-2013

Locks

Note: Be careful when opening or closing the liftgate in a garage or other enclosed area to avoid damaging the liftgate. Note: Do not hang anything (bike rack, etc.) from the spoiler, glass or liftgate. This could damage the liftgate and its components. Note: Do not leave the liftgate open while driving. This could damage the liftgate and its components. Opening and Closing the Liftgate To Open the Liftgate

Press the button located in the top of the liftgate pull cup handle to unlatch the liftgate, then pull on the outside handle. Opening With the Remote Control

Press the button twice within three seconds.

Left-Hand Side Turn clockwise to lock. Right-Hand Side Turn counterclockwise to lock. MANUAL LIFTGATE WARNINGS

It is extremely dangerous to ride in the cargo area, inside or outside of your vehicle. In a collision, people

riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that does not have seats and safety belts. Make sure everyone in your vehicle is in a seat and using a safety belt correctly.

Make sure that the liftgate is closed to prevent exhaust fumes from being drawn into your vehicle. This will also prevent passengers and cargo from falling out. If you must drive with the liftgate door open, keep your vehicle well ventilated so outside air does not enter your vehicle.

55

Fiesta (CCT) Vehicles Built From: 01-04-2013, Vehicles Built Up To: 31-12-2013

E112203E138632Locks

To Close the Liftgate

Passive locking and unlocking requires a valid passive key to be located within one of the three external detection ranges. These are located approximately five feet (one and a half meters) from the front door handles and the liftgate. Passive Key