2016 Ford Explorer Owners Manual

Information Displays

Action

Objects are by the passenger seat. After you move the objects away from the seat, if the warning stays on or continues to come on, contact an authorized dealer as soon as possible.

Seats

Message

Occupant Sensor BLOCKED Remove

Objects Near Passenger

Seat

Memory Recall Not

Permitted While Driving

A reminder that memory seats are not available while driving.

Memory X Saved

Shows where you have saved your memory setting.

Starting System

Message

To START Press Brake Cranking Time Exceeded

Engine Start Pending

Please Wait

Action

A reminder to apply the brake when starting your vehicle. The starter has exceeded its cranking time in attempting to

start your vehicle.

The starter is attempting to start your vehicle.

Pending Start Cancelled

The system has cancelled the pending start.

Tire Pressure Monitoring System

Message

LOW Tire Pressure

Tire Pressure Monitor

Fault

Tire Pressure Sensor

Fault

Action

One or more tires on your vehicle have low tire pressure. See

Tire Pressure Monitoring System (page 325).

The tire pressure monitoring system is malfunctioning. If the authorized dealer. See Tire Pressure Monitoring System

warning stays on or continues to come on, contact an

(page 325).

A tire pressure sensor is malfunctioning, or your spare tire is in use. If the warning stays on or continues to come on, contact an authorized dealer as soon as possible. See Tire Pressure

Monitoring System (page 325).

126

Explorer (TUB), enUSA, First Printing

Information Displays

Terrain Management System

Message

Normal Mode Active Snow, Gravel, Grass

Mode Active

Mud, Rut Mode Active

Sand Mode Active Terrain Management

System Fault

Mode Change Not Accepted, Retry

Traction Control

Message

Traction Control Off

Traction Control On

Trailer

Message

Action

Displays terrain management normal mode is currently active.

Displays terrain management snow, gravel, grass mode is

currently active.

Displays terrain management mud, ruts mode is currently

active.

Displays terrain management sand mode is currently active. Displays when the terrain management system detects an

error.

Displayed when terrain management mode cannot be

changed at the time of your request.

Action

Displays the status of the traction control system. See Using

Traction Control (page 192).

Displays the status of the traction control system. See Using

Traction Control (page 192).

Action

Trailer Sway Reduce

Speed

Displays when the trailer sway control has detected a trailer

sway. See Trailer Sway Control (page 244).

127

Explorer (TUB), enUSA, First Printing

Information Displays

Transmission Message

Transmission Malfunc-

tion Service Now

Transmission Overtem- perature Stop Safely Transmission Over- heating Stop Safely Transmission Service

Required

Transmission Too Hot

Press Brake

Transmission Limited Function See Manual Transmission Warming

Up Please Wait

Transmission Not in Park

Press Brake Pedal

Transmission Adjusted Transmission Adapt-

Mode

Transmission Indicat-

Mode Lockup On

Transmission Indicat-

Mode Lockup Off

Action

Contact an authorized dealer.

The transmission is overheating and needs to cool. Stop in a

safe place as soon as possible.

The transmission is overheating and needs to cool. Stop in a

safe place as soon as possible. Contact an authorized dealer.

The transmission is getting hot. Stop to let it cool.

The transmission has overheated and has limited functionality.

See Automatic Transmission (page 180).

The transmission is too cold. Wait for it to warm up before

you drive.

A reminder to shift into park.

A request for you to apply the brake as needed by the trans-

mission.

The transmission has adjusted the shift strategy. The transmission is adjusting the shift strategy.

The transmission is locked and unable to select gears.

The transmission is unlocked and free to select gears.

128

Explorer (TUB), enUSA, First Printing

Climate Control

MANUAL CLIMATE CONTROL

Fan speed control: Adjust the volume of air circulated in the vehicle. Power: Press the button to switch the system on and off. When the system is off, it prevents outside air from entering the vehicle. Air distribution control: Adjust the control to turn airflow from the windshield, instrument panel, or footwell vents on or off. You can distribute air through the following combinations: windshield, windshield/floor, panel, panel/floor, and floor. Note: At least one of these buttons illuminates when the system is on. A/C: Press the button to switch the air conditioning on or off. Air conditioning cools your vehicle using outside air. To improve the time to reach a comfortable temperature in hot weather, drive with the windows open until you feel cold air through the air vents. Note: In certain conditions (for example, maximum defrost), the air conditioning compressor may continue to operate even though the air conditioning is switched off.

129

Explorer (TUB), enUSA, First Printing

E193398Climate Control

MAX A/C: Adjust the control for maximum cooling. Recirculated air flows through the instrument panel vents, air conditioning automatically turns on and the fan automatically adjusts to the highest speed. Temperature control: Controls the temperature of the air circulated in your vehicle. Note: To prevent window fogging, you cannot select recirculated air when maximum defrost is on. Recirculated air: Press the button to switch between outside air and recirculated air. The air currently in the passenger compartment recirculates. This can reduce the time needed to cool the interior and reduce unwanted odors from entering your vehicle. Note: Recirculated air may also turn on and off automatically in instrument panel or instrument panel and floor airflow modes during hot weather to improve cooling efficiency. Rear passenger temperature control: Adjust the temperature to the rear of the passenger compartment. Rear climate control lock: When illuminated, you can only operate the rear passenger settings through the front controls. Rear passenger power: Press the button to switch the system on and off. Rear fan speed control: Adjust the volume of air circulated to the rear of the passenger compartment. Heated rear window: Press the button to switch the heated rear window on and off.

130

Explorer (TUB), enUSA, First Printing

Climate Control

AUTOMATIC CLIMATE CONTROL - VEHICLES WITH: PREMIUM AM/FM/CD

Power: Press the button to switch the system on and off. When the system is off, it prevents outside air from entering the vehicle. Heated seats (if equipped): Press the button to switch the heated seats on and off. Driver temperature control: Adjust the temperature setting using the control on the driver side. Heated rear window: Press the button to switch the heated rear window on and off. MAX Defrost: Press the button to switch on defrost. Outside air flows through the windshield vents, air conditioning automatically turns on, and fan automatically adjusts to the highest speed. You can also use this setting to defrost and clear the windshield of a thin covering of ice. The heated rear window also automatically turns on when you select maximum defrost. Note: To prevent window fogging, you cannot select recirculated air when maximum defrost is on. Air distribution control: Adjust the control to turn airflow from the windshield, instrument panel, or footwell vents on or off. You can distribute air through the following combinations: windshield, windshield/floor, panel, panel/floor, and floor.

131

Explorer (TUB), enUSA, First Printing

E193399Climate Control

A/C: Press the button to switch the air conditioning on or off. Air conditioning cools your vehicle using outside air. To improve the time to reach a comfortable temperature in hot weather, drive with the windows open until you feel cold air through the air vents. Note: In certain conditions (for example, maximum defrost), the air conditioning compressor may continue to operate even though the air conditioning is switched off. MAX A/C: Press the button for maximum cooling. Recirculated air flows through the instrument panel vents, air conditioning automatically turns on and the fan automatically adjusts to the highest speed. Passenger temperature control: Adjust the temperature on the passenger side. DUAL: Press the button to switch on control for the passenger side of the vehicle. Recirculated air: Press the button to switch between outside air and recirculated air. The air currently in the passenger compartment recirculates. This can reduce the time needed to cool the interior and reduce unwanted odors from entering your vehicle. Note: Recirculated air may also turn on and off automatically in instrument panel or instrument panel and floor airflow modes during hot weather to improve cooling efficiency. Fan speed control: Adjust the volume of air circulated in the vehicle. AUTO: Press the button to switch on automatic operation. Adjust to select the desired temperature. Fan speed, air distribution, air conditioning operation, and outside or recirculated air are automatically adjusted to heat or cool the vehicle to maintain the desired temperature. You can also switch off dual zone mode by pressing and holding the button for more than two seconds.

AUTOMATIC CLIMATE CONTROL - VEHICLES WITH: SONY AUDIO SYSTEM Note: You can switch temperature units between Fahrenheit and Celsius.

132

Explorer (TUB), enUSA, First Printing

Climate Control

A/C: Press the button to switch the air conditioning on or off. Air conditioning cools your vehicle using outside air. To improve the time to reach a comfortable temperature in hot weather, drive with the windows open until you feel cold air through the air vents. Note: In certain conditions (for example, maximum defrost), the air conditioning compressor may continue to operate even though the air conditioning is switched off. MAX A/C: Press the button for maximum cooling. Recirculated air flows through the instrument panel vents, air conditioning automatically turns on, and the fan automatically adjusts to the highest speed. Recirculated air: Press the button to switch between outside air and recirculated air. The air currently in the passenger compartment recirculates. This can reduce the time needed to cool the interior and reduce unwanted odors from entering your vehicle. Note: Recirculated air may also turn on and off automatically in instrument panel or instrument panel and floor airflow modes during hot weather to improve cooling efficiency.

133

Explorer (TUB), enUSA, First Printing

E193400Climate Control

DUAL: Press the button to switch on control for the passenger side of the vehicle. Heated seats (if equipped): Press the button to switch the heated seats on and off. Passenger temperature control: Adjust the temperature on the passenger side. Climate controlled seats: Press the button to switch the climate controlled seats on and off. Fan speed control: Adjust the volume of air circulated in the vehicle. Power: Press the button to switch the system on and off. When the system is off, it prevents outside air from entering the vehicle. Driver temperature control: Adjust the temperature setting using the control on the driver side. This control also adjusts the passenger side temperature when you switch off dual zone mode. Heated rear window: Press the button to switch the heated rear window on and off. Defrost: Select to distribute air through the windshield air vents. Air distribution to the instrument panel and footwell vents turns off. You can also use this setting to defrost and clear the windshield of a thin covering of ice. MAX Defrost: Press the button to switch on defrost. Outside air flows through the windshield vents, air conditioning automatically turns on, and fan automatically adjusts to the highest speed. You can also use this setting to defrost and clear the windshield of a thin covering of ice. The heated rear window also automatically turns on when you select maximum defrost. Note: To prevent window fogging, you cannot select recirculated air when maximum defrost is on. AUTO: Press the button to switch on automatic operation. Adjust to select the desired temperature. Fan speed, air distribution, air conditioning operation, and outside or recirculated air are automatically adjusted to heat or cool the vehicle to maintain the desired temperature. You can also turn off dual zone mode by pressing and holding the button for greater than two seconds.

HINTS ON CONTROLLING THE INTERIOR CLIMATE General Hints Note: Prolonged use of recirculated air may cause the windows to fog up.

Note: You may feel a small amount of air from the footwell air vents regardless of the air distribution setting. Note: To reduce humidity build-up inside your vehicle, do not drive with the system switched off or with recirculated air always switched on.

134

Explorer (TUB), enUSA, First Printing

Climate Control

Note: Do not place objects under the front seats as this may interfere with the airflow to the rear seats. Note: Remove any snow, ice or leaves from the air intake area at the base of the windshield. Note: To improve the time to reach comfort in hot weather, drive with the windows fully open until you feel cold air through the air vents. Manual Climate Control Note: To reduce fogging of the windshield during humid weather, adjust the air distribution control to the windshield air vents position.

Heating the Interior Quickly

Vehicle with manual climate control Adjust the fan speed to a high speed setting. Adjust the temperature control to the highest setting. Select the footwell air vents using the air distribution buttons.

Automatic Climate Control Note: Adjusting the settings when your vehicle interior is extremely hot or cold is not necessary. The system automatically adjusts to heat or cool the cabin to your selected temperature as quickly as possible. For the system to function efficiently, the instrument panel and side air vents should be fully open. Note: If you select AUTO during cold outside temperatures, the system directs airflow to the windshield and side window vents. In addition, the fan may run at a slower speed until the engine warms up. Note: If you select AUTO during hot outside temperatures, or when the inside of the vehicle is hot, the system automatically uses recirculated air to maximize interior cooling. When the interior reaches the selected temperature, the system automatically switches to using outside air.

Vehicle with automatic climate control Press the AUTO button.

Adjust the temperature control to the desired setting.

135

Explorer (TUB), enUSA, First Printing

Climate Control

Recommended Settings for Heating Vehicle with manual climate control

Adjust the fan speed to the center setting. Adjust the temperature control to the midway point of the hot settings.

Select the footwell air vents using the air distribution buttons.

Cooling the Interior Quickly

Vehicle with manual climate control Adjust the temperature control to the MAX A/C position. Drive with the windows fully open until you feel cold air through the air vents.

Recommended Settings for Cooling Vehicle with manual climate control

Adjust the fan speed to the center setting. Adjust the temperature control to the midway point of the cold settings.

Select the instrument panel air vents using the air distribution buttons.

Vehicle with automatic climate control Press the AUTO button.

Adjust the temperature control to the desired setting. Use 72°F (22°C) as a starting point, then adjust the setting as necessary.

Vehicle with automatic climate control Press the MAX A/C button.

Vehicle with automatic climate control Press the AUTO button.

Adjust the temperature control to the desired setting. Use 72°F (22°C) as a starting point, then adjust the setting as necessary.

136

Explorer (TUB), enUSA, First Printing

Climate Control

Side Window Defogging in Cold Weather

Vehicle with manual climate control

Select the windshield air vents using the air distribution buttons. Press the A/C button.

Vehicle with automatic climate control Press the defrost button.

Adjust the temperature control to the desired setting. Use 72°F (22°C) as a starting point, then adjust the setting as necessary.

Adjust the temperature control to the desired setting. Adjust the fan speed to the highest setting.

REAR PASSENGER CLIMATE CONTROLS

137

Explorer (TUB), enUSA, First Printing

E188689Climate Control

Fan speed control: Adjust the volume of air circulated in the vehicle. Heated seats (if equipped): Press the button to switch the heated seats on and off. See Heated Seats (page 154). Temperature control: Control the temperature of the air circulated in your vehicle. Air distribution control: Adjust the control to turn airflow from the instrument panel or footwell vents on or off. You can distribute air through any combination of these vents. Fan speed control lock: When illuminated, you can only operate the rear passenger settings through the front controls.

•

•

CABIN AIR FILTER Your vehicle is equipped with a cabin air filter, which gives you and your passengers the following benefits: •

It improves your driving comfort by reducing particle concentration. It improves the interior compartment cleanliness. It protects the climate control components from particle deposits. You can locate the cabin air filter behind the glove box. Note: Make sure you have a cabin air filter installed at all times. This prevents foreign objects from entering the system. Running the system without a filter in place could result in degradation or damage to the system. Replace the filter at regular intervals. See Scheduled Maintenance (page 486). For additional cabin air filter information, or to replace the filter, see an authorized dealer.

HEATED WINDOWS AND MIRRORS (If Equipped) Heated Rear Window Note: Make sure the engine is running before operating the heated windows. Press the button to clear the heated rear window of thin ice and fog. The heated rear window

will automatically turn off after a short period of time. Start the engine before you switch the heated rear window on. Note: Do not use razor blades or other sharp objects to clean or remove decals from the inside of the heated rear window. The vehicle warranty does not cover damage caused to the heated rear window grid lines. Heated Exterior Mirror When you switch the heated rear window on, the heated exterior mirrors will automatically turn on. Note: Do not remove ice from the mirrors with a scraper or adjust the mirror glass when it is frozen in place. Note: Do not clean the mirror housing or glass with harsh abrasives, fuel or other petroleum-based cleaning products.

138

Explorer (TUB), enUSA, First Printing

E184884Climate Control

REMOTE START (If Equipped) The remote start feature allows you to pre-condition the interior of your vehicle. The climate control system works to achieve comfort according to your previous settings. Note: You cannot adjust the system during remote start operation. Turn the ignition on to return the system to its previous settings. You can now make adjustments normally, but you need to turn certain vehicle-dependent features back on, such as: • Heated seats. • Cooled seats. • Heated steering wheel. • Heated mirrors. • Heated rear window. You can adjust the default remote start settings using the information display controls. See Information Displays (page 101). Automatic Settings In hot weather, the system is set to 72°F (22°C). The cooled seats are set to high (if available, and selected to AUTO in the information display). In moderate weather, the system either heats or cools (based on previous settings). The rear defroster, heated mirrors and heated seats do not automatically turn on. In cold weather, the system is set to 72°F (22°C). The heated seats are set to high (if available, and selected to AUTO in the information display). The rear defroster and heated mirrors automatically turn on.

139

Explorer (TUB), enUSA, First Printing

Seats

We recommend that you follow these guidelines: •

Sit in an upright position with the base of your spine as far back as possible.

• Do not recline the seatback more than

30 degrees.

• Adjust the head restraint so that the top of it is level with the top of your head and as far forward as possible. Make sure that you remain comfortable. Keep sufficient distance between yourself and the steering wheel. We recommend a minimum of 10 in (25 cm) between your breastbone and the airbag cover.

•

• Hold the steering wheel with your arms

slightly bent. Bend your legs slightly so that you can press the pedals fully.

•

• Position the shoulder strap of the safety belt over the center of your shoulder and position the lap strap tightly across your hips.

Make sure that your driving position is comfortable and that you can maintain full control of your vehicle. HEAD RESTRAINTS WARNINGS

Fully adjust the head restraint before you sit in or operate your vehicle. This will help minimize the risk of neck

injury in the event of a crash. Do not adjust the head restraint when your vehicle is moving.

The head restraint is a safety device. Whenever possible it should be installed and properly adjusted when

the seat is occupied.

SITTING IN THE CORRECT POSITION

WARNINGS

Sitting improperly, out of position or with the seatback reclined too far can take weight off the seat cushion and affect the decision of the passenger sensing system, resulting in serious injury or death in the event of a crash. Always sit upright against your seat back, with your feet on the floor.

Do not recline the seatback as this can cause the occupant to slide under the safety belt, resulting in

serious injury in the event of a crash.

Do not place objects higher than the seatback to reduce the risk of serious injury in the event of a crash or during

heavy braking.

When you use them properly, the seat, head restraint, safety belt and airbags will provide optimum protection in the event of a crash.

140

Explorer (TUB), enUSA, First Printing

E68595Seats

WARNINGS

Install the head restraint properly to help minimize the risk of neck injury in the event of a crash.

Note: Adjust the seatback to an upright driving position before adjusting the head restraint. Adjust the head restraint so that the top of it is level with the top of your head and as far forward as possible. Make sure that you remain comfortable. If you are extremely tall, adjust the head restraint to its highest position. Front seat head restraints

Second-row center seat head restraint (If equipped)

The head restraints consist of:

An energy absorbing head restraint. Two steel stems. Guide sleeve adjust and release button. Guide sleeve unlock and remove button.

Adjusting the Head Restraint Raising the Head Restraint Pull the head restraint up. Lowering the Head Restraint 1. Press and hold button C. 2. Push the head restraint down. Removing the Head Restraint 1. Pull the head restraint up until it

reaches its highest position.

2. Press and hold buttons C and D. 3. Pull the head restraint up.

141

Explorer (TUB), enUSA, First Printing

E138642E138645Seats

Installing the Head Restraint Align the steel stems into the guide sleeves and push the head restraint down until it locks. Second-row outboard seat head restraints

Third-row head restraints

The head restraints consist of:

An energy absorbing head restraint. Two steel stems. Fold strap.

Folding the Head Restraint Pull the fold strap (C). Pull it back up to reset. Note: Press the stow or fold button on the power folding seats to automatically fold the head restraint. Tilting Head Restraints (If Equipped) The front head restraints tilt for extra comfort. To tilt the head restraint, do the following:

The head restraints consist of:

An energy absorbing head restraint. Two steel stems. Guide sleeve unlock and remove button. Fold button.

Folding the Head Restraint 1. Press and hold button D. 2. Pull it back up to reset. Removing the Head Restraint 1. Fold the head restraint. 2. Press and hold both C buttons. 3. Pull the head restraint up. Installing the Head Restraint Align the steel stems into the guide sleeves and push the head restraint down until it locks.

142

Explorer (TUB), enUSA, First Printing

E201128E190836Seats

Recline Adjustment WARNING

Always drive and ride with your seatback upright and the lap belt snug and low across the hips.

1. Adjust the seatback to an upright

driving or riding position.

2. Pivot the head restraint forward toward

your head to the desired position. After the head restraint reaches the forward-most tilt position, pivoting it forward again will then release it to the rearward, un-tilted position. MANUAL SEATS (If Equipped) Moving the Seat Backward and Forward

WARNINGS

Do not adjust the driver seat or seatback when your vehicle is moving. Rock the seat backward and forward after releasing the lever to make sure that it is fully engaged.

143

Explorer (TUB), enUSA, First Printing

E144727E190838E190837Seats

Lumbar Adjustment (If Equipped)

POWER SEATS

WARNINGS

Do not adjust the driver seat or seatback when your vehicle is moving. Adjusting your seatback

while the vehicle is in motion may cause loss of control of the vehicle.

Do not place cargo or any objects behind the seatback before returning it to the original position.

144

Explorer (TUB), enUSA, First Printing

E190839E176038Power Lumbar (If Equipped)

Seats

Note: The engine must be running or the vehicle must be in accessory mode to activate the seats. Note: Allow a few seconds for any selection to activate. The seatback and cushion massage cannot function at the same time.

Multi-Contour Front Seats With Active Motion (If Equipped) Note: The massage system will turn off after 20 minutes.

Massage mode

Lumbar and bolster mode

Back massage intensity

adjustment

Upper lumbar

Massage intensity decrease

Lumbar decrease

and off*

Cushion massage intensity

adjustment

Lower lumbar**

Massage intensity increase

Lumbar increase

On and off

*The massage feature will default to an alternating massage mode with back massage intensity adjustment. The lumbar and bolster feature will default to the middle lumbar mode. **Press C a second time to adjust the back bolster. Press C a third time to adjust the cushion bolster.

You can also adjust this feature through the touchscreen. When switched on, the system displays directions for you to adjust the lumbar settings in your seat or to set the massage function. To access and make adjustments to the lumbar setting: 1. Press the Menu Settings icon > Vehicle

> Multi-contour Seat.

2. Choose the desired seat to adjust. 3. Press the + or - to adjust the lumbar

intensity.

145

Explorer (TUB), enUSA, First Printing

E176039E156301Seats

Saving a PreSet Position 1. Switch the ignition on. 2. Adjust the memory features to your

desired position.

3. Press and hold the desired preset button until you hear a single tone.

You can save up to three preset memory positions. You can save a memory preset at any time. Recalling a PreSet Position Press and release the preset button associated with your desired driving position. The memory features move to the position stored for that preset. Note: You can only recall a preset memory position when the ignition is off, or when the transmission is in park (P) or neutral (N) (and your vehicle is not moving) if the ignition is on. You can also recall a preset memory position by: • Pressing the unlock button on your

intelligent access key fob if it is linked to a preset position.

• Unlocking the intelligent driver door handle if a linked key fob is present. Entering a personal entry code on the Securicode keypad. See Locks (page 60).

•

Note: Using a linked key fob to recall your memory position when the ignition is off moves the seat to the Easy Entry position. Note: Pressing any active memory feature adjustment control (or any memory button) during a memory recall cancels the operation.

To access and make adjustments to the massage setting: 1. Press the Menu Settings icon > Vehicle

>Multi-contour Seat.

2. Choose the desired seat to adjust. 3. Press Off, Lo or Hi. MEMORY FUNCTION (If Equipped)

WARNINGS

Before activating the seat memory, make sure that the area immediately surrounding the seat is clear of

obstructions and that all occupants are clear of moving parts.

Do not use the memory function when your vehicle is moving.

This feature automatically recalls the position of the following: • Driver seat. • Power mirrors. • Optional power adjustable foot pedals. • Optional steering column. The memory control is located on the driver door.

146

Explorer (TUB), enUSA, First Printing

E142554Seats

Linking a PreSet Position to your Remote Control or Intelligent Access Key Fob Your vehicle can save the preset memory positions for up to three remote controls or intelligent access (IA) keys. 1. With the ignition on, move the memory

positions to the desired positions. 2. Press and hold the desired preset

button for about five seconds. A tone sounds after about two seconds. Continue holding until you hear a second tone.

REAR SEATS Adjusting the Rear Seats Second Row Seats

WARNINGS

Always drive and ride with your seatback upright and the lap belt snug and low across the hips. Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe

personal injuries in the event of a crash.

3. Within three seconds, press the lock button on the remote control you are linking.

To unlink a remote control, follow the same procedure – except in step 3, press the unlock button on the remote control. Note: If more than one linked remote control or intelligent access key is in range, the memory function moves to the settings of the first key to recall a memory position. Easy Entry and Exit Feature If you enable the easy entry and exit feature, it automatically moves the driver seat position rearward up to two inches (five centimeters) when you switch the ignition off. The driver seat returns to the previous position when you switch the ignition on. You can enable or disable this feature in the information display. See Information Displays (page 101).

Recline Adjustment

Lift the handle to adjust the seatback rearward or forward. The seatback can also fold forward until it is flat. Fold flat seatback

147

Explorer (TUB), enUSA, First Printing

E190840E190841Seats

Lift the handle and fold the seatback forward until it is flat. Note: For the bench seats, make sure the center safety belt is unbuckled before folding the seatback. Moving the Seats Backward and Forward (If equipped)

Note: Remove items from the second-row seat. Make sure that no bulky objects such as purses or briefcases are on the floor in front of the second-row seats before tumbling them. Note: For second-row bench seats, make sure the center safety belt is unbuckled before folding the seatback. Note: You may have to move the front-row seat forward to allow the second-row seat to be fully tumbled. Note: You may have to lower the center head restraint. See Head Restraints (page 140). Fold and tumble the second-row seat to access the third row:

Third Row Seats (Manual Seats)

WARNINGS

Before returning the seatback to its original position, make sure that cargo or any objects are not trapped

behind the seatback. After returning the seatback to its original position, pull on the seatback to make sure that it has fully latched. An unlatched seat may become dangerous in the event of a sudden stop or crash.

Do not adjust or release the seat floor latch while vehicle is in motion. Do not operate the vehicle with seats in the tumbled position. Always latch the vehicle seat to the floor, whether the seat is occupied or empty. If not latched or if the seat is tumbled, the seat may cause injury during a sudden stop.

Explorer (TUB), enUSA, First Printing

1. Fold the outboard head restraint.

2. Lift the handle located on the side of

the seat to fold the seatback flat.

148

E190838E193964E190843Seats

5. Lift the seatback toward the rear of the vehicle, and rotate the seatback until you hear a click, locking it in the upright position. Note: The seatback will not raise if the rear latch hooks are not properly engaged to the floor striker. If the seatback does not raise, then repeat Step 4.

6. Pull the head restraint back up to its

normal adjusted position.

3. Lift the handle all the way up until the seat releases from the floor. Rotate the seat forward to allow access to the third row.

4. To return the seatback to the floor from the tumbled position, rotate the seat down until you hear it latching to the floor.

149

Explorer (TUB), enUSA, First Printing

Make sure that the rear latch hooks are properly engaged with the floor striker. Note: Make sure that the seat and seatback are latched securely in position. Keep floor area free of objects that would prevent proper seat engagement. Third Row Seat Access (Power Fold and Tumble Seat-If equipped)

WARNING

Make sure that the seat is unoccupied when folding it down. Folding the seat while occupied

could result in occupant injury or damage to the seat.

E190844E190845E190846E190847Seats

The control is located at the back of the rear door opening. Press and hold it to fold the seatback down and tumble the seat forward for access to the third row. Third Row Seat Exit (Manual Seat, Power Fold and Tumble Seat)

1. Fold the outboard head restraint.

2. Pull on the strap located on the back of the second row seat. This will fold the seatback forward. Pull the strap a second time to tumble the seat forward, allowing easy exit from the third row seat.

WARNINGS

Before returning the seatback to its original position, make sure that cargo or any objects are not trapped

behind the seatback. After returning the seatback to its original position, pull on the seatback to make sure that it has fully latched. An unlatched seat may become dangerous in the event of a sudden stop or crash.

Do not adjust or release the seat floor latch while vehicle is in motion. Do not operate the vehicle with seats in the tumbled position. Always latch the vehicle seat to the floor, whether the seat is occupied or empty. If not latched or if the seat is tumbled, the seat may cause injury during a sudden stop.

Note: You may have to lower the center head restraint. See Head Restraints (page 140).

150

Explorer (TUB), enUSA, First Printing

E190848E193964E190849E190850Seats

3. To return the seatback to the floor from the tumbled position, rotate the seat down until you hear it latching to the floor.

Folding the Third Row Manual Seat 1. Remove all objects from the seat and

stowage tub.

2. Fold the outboard head restraint by

pulling the head restraint release strap.

4. Lift the seatback toward the rear of the vehicle, and rotate the seatback until you hear a click, locking it in the upright position. Note: The seatback will not raise if the rear latch hooks are not properly engaged to the floor striker. If the seatback does not raise, then repeat Step 3.

5. Pull the head restraint back up to its

normal adjusted position.

3. From the rear of the vehicle, fold the

seatback by pulling and holding the red strap while pushing the seatback forward. Release the strap once the seatback starts rotating forward.

Make sure that the rear latch hooks are properly engaged with the floor striker. Note: Make sure that the seat and seatback are latched securely in position. Keep floor area free of objects that would prevent proper seat engagement.

151

Explorer (TUB), enUSA, First Printing

E190846E190847E193843E190854Seats

WARNINGS

Before returning the seatback to its original position, make sure that cargo or any objects are not trapped

behind the seatback. After returning the seatback to its original position, pull on the seatback to make sure that it has fully latched. An unlatched seat may become dangerous in the event of a sudden stop or crash.

4. Release the cushion latches by pulling the short black strap while pulling on the strap located at the top of the seatback to tumble the seat all the way into the tub in the floor.

Note: Do not use the seat anchors as cargo tie downs.

Do not drive the vehicle when the third-row seat is rotated backwards. During a sudden stop, the safety

belts are not functional in this position and the third-row seat can rapidly tip back to the forward position, all of which may result in serious injury.

Note: Do not use the third row seat back as a load floor when the seatback is folded. Note: Make sure that the area under the seat is free of objects before stowing it. Unfolding the Third Row Manual Seat

Note: Make sure that there are no objects such as books, purses or briefcases on the load floor before unstowing the seat. Failure to remove all objects from the top of the load floor prior to unstowing it may cause damage to the seat. Note: Make sure the area under the load floor is free of objects before unstowing it.

WARNINGS

Make sure seat is latched to vehicle floor by pushing and pulling on the seat. If not latched, the seat may

cause injury during a sudden stop.

152

Explorer (TUB), enUSA, First Printing

E190923E190924E190927Seats

1. Unlatch and lift the seat out of the tub in the floor by squeezing and pulling up on the handle. Once the seat is at a vertical position, push the seat over, letting it fall onto the latches.

2. To return the seatback to the upright position, pull the red strap. Then while holding the red strap, pull the long strap located on the seatback to raise the seatback.

3. Pull the head restraints up to their

normal positions.

PowerFold™Third Row Seats (If equipped) The third row power seat buttons are located behind the third row seats on the left-hand quarter trim panel.

NORMAL: Press to return the seat to the normal seating position. STOW: Press to stow the seat into the tub floor.

153

Explorer (TUB), enUSA, First Printing

E190925E190926E190928Seats

FOLD: Press to fold down the seatback. RH / BOTH / LH: Press to select the normal, stow and fold modes to activate the right-hand seat, the left-hand seat or both.

HEATED SEATS (If Equipped) Front Seats

WARNING

People who are unable to feel pain to their skin because of advanced age, chronic illness, diabetes, spinal

cord injury, medication, alcohol use, exhaustion or other physical conditions, must exercise care when using the heated seat. The heated seat may cause burns even at low temperatures, especially if used for long periods of time. Do not place anything on the seat that insulates against heat, such as a blanket or cushion. This may cause the heated seat to overheat. Do not puncture the seat with pins, needles or other pointed objects. This may damage the heating element which may cause the heated seat to overheat. An overheated seat may cause serious personal injury.

Do not do the following: • Place heavy objects on the seat. • Operate the heated seat if water or any other liquid spills on the seat. Allow the seat to dry thoroughly.

• Operate the heated seats unless the engine is running. Doing so can cause the battery to lose charge.

Note: The third row seat includes obstacle detection that allows the seat to stop and reverse direction if it hits an obstacle so that the obstacle can be removed. Note: Pressing a different button while the power seat feature is already being performed may cause the first selected seat movement to be cancelled. Allow the first seat movement to be completed before pressing a button for another function. Note: Make sure that there are no objects such as books, purses or briefcases on the load floor before unstowing the seat. Failure to remove all objects from the top of the load floor prior to unstowing it may cause damage to the seat. Note: In order to allow the seat to complete the stowed position, do not place objects under the seat before stowing. Remove all objects from the seat and stowage tub. Note: In the unlikely event that the third row power seat stops prematurely or travels to an unexpected position, press the FOLD button (C) to reset the seat and return it to a normal position. These seats feature a power one-touch operation that allows you fold and stow the seats. •

The power fold seats work only when the transmission is in park (P) and the liftgate is open. If the ignition is off and the feature is still running, the battery saver will turn it off after 10 minutes. Press unlock on the remote entry key transmitter to reactivate the power seats or unlock it with the keyless entry keypad. See Remote Control (page 49).

•

154

Explorer (TUB), enUSA, First Printing

Seats

The rear seat heat controls are located on the rear of the center console.

Press the heated seat symbol to cycle through the various heat settings and off. More indicator lights indicate warmer settings. The heated seat module resets at every ignition run cycle. While the ignition is on, press the high or low heated seat switch to enable heating mode. When activated, they will turn off automatically when you turn the engine off. CLIMATE CONTROLLED SEATS (If Equipped) Heated Seats

Press the heated seat symbol to cycle through the various heat settings and off. More indicator lights indicate warmer settings. Rear Seats (If Equipped)

WARNING

Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion, or other physical conditions, must exercise care when using the seat heater. The seat heater may cause burns even at low temperatures, especially if used for long periods of time. Do not place anything on the seat that insulates against heat, such as a blanket or cushion, because this may cause the seat heater to overheat. Do not puncture the seat with pins, needles, or other pointed objects because this may damage the heating element which may cause the seat heater to overheat. An overheated seat may cause serious personal injury.

Do not do the following: • Place heavy objects on the seat. • Operate the seat heater if water or any other liquid is spilled on the seat. Allow the seat to dry thoroughly.

• Operate the heated seats unless the engine is running. Doing so can cause the battery to lose charge.

155

Explorer (TUB), enUSA, First Printing

E146322E146322Seats

WARNING

Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion, or other physical conditions, must exercise care when using the seat heater. The seat heater may cause burns even at low temperatures, especially if used for long periods of time. Do not place anything on the seat that insulates against heat, such as a blanket or cushion, because this may cause the seat heater to overheat. Do not puncture the seat with pins, needles, or other pointed objects because this may damage the heating element which may cause the seat heater to overheat. An overheated seat may cause serious personal injury.

Note: Do not do the following: • Place heavy objects on the seat. • Operate the seat heater if water or any other liquid spills on the seat. Allow the seat to dry thoroughly.

• Operate the heated seats unless the engine is running. Doing so can cause the battery to lose charge.

Cooled Seats The cooled seats only function when the engine is running.

To operate the cooled seats: Touch the cooled seat symbol to cycle through the various cooling settings and off. More indicator lights indicate cooler settings. If the engine falls below 350 RPM while the cooled seats are on, the feature turns itself off. You need to reactivate it. Climate controlled seat air filter replacement Your vehicle is equipped with lifetime air filters that are integrated with the seats. Regular maintenance or replacement is not needed.

Touch the heated seat symbol to cycle through the various heat settings and off. More indicator lights indicate warmer settings.

156

Explorer (TUB), enUSA, First Printing

E146322E146309Universal Garage Door Opener (If Equipped)

HomeLink Wireless Control System

WARNINGS

Make sure that the garage door and security device are free from obstruction when you are

programming. Do not program the system with the vehicle in the garage.

Do not use the system with any garage door opener that does not have the safety stop and reverse

feature as required by U.S. Federal Safety Standards (this includes any garage door opener manufactured before April 1, 1982). A garage door opener which cannot detect an object, signaling the door to stop and reverse, does not meet current federal safety standards. Using a garage door opener without these features increases the risk of serious injury or death.

Note: Make sure you keep the original remote control transmitter for use in other vehicles as well as for future system programming. Note: We recommend that upon the sale or lease termination of your vehicle, you erase the programmed function buttons for security reasons. See Erasing the Function Button Codes. Note: You can program a maximum of three devices. To change or replace any of the three devices after it has been initially programmed, you must first erase the current settings. See Erasing the Function Button Codes.

The universal garage door opener replaces the common hand-held garage door opener with a three-button transmitter that is integrated into the driver’s sun visor. The system includes two primary features, a garage door opener and a platform for remote activation of devices within the home. As well as being programmed for garage doors, the system transmitter can be programmed to operate entry gate operators, security systems, entry door locks and home or office lighting. Additional system information can be found online at www.homelink.com, www.youtube.com/HomeLinkGentex or by calling the toll-free help line on 1-800-355-3515. In-Vehicle Programming This process is to program your hand-held transmitter and your in-vehicle HomeLink button. Note: The programming steps below assume you will be programming HomeLink that was not previously programmed. Note: Put a new battery in the hand-held transmitter. This will ensure quicker training and accurate transmission of the radio-frequency signal.

157

Explorer (TUB), enUSA, First Printing

E142657Universal Garage Door Opener (If Equipped)

To program additional buttons, repeat Steps 1 – 4. For questions or comments, please contact HomeLink at www.homelink.com, www.youtube.com/HomeLinkGentex or 1-800-355-3515. Programming Your Garage Door Opener Motor Note: You may need a ladder to reach the unit and you may need to remove the cover or lamp lens on your garage door opener.

1. Press the learn button on the garage

door opener motor and then you have 30 seconds to complete the next two steps.

2. Return to your vehicle.

3. Press and hold the function button you

want to program for 2 seconds, then release. Repeat this step. Depending on your brand of garage door opener, you may need to repeat this sequence a third time.

1. With your vehicle parked outside of the

garage, turn your ignition to the on position, but do not start your vehicle.

2. Hold your hand-held garage door

transmitter 2–6 in (5–14 cm) away from the HomeLink button you want to program.

3. Using both hands, simultaneously,

press and hold the desired HomeLink button and the hand-held transmitter button. DO NOT release either one until the HomeLink indicator light flashes slowly and then rapidly. When the indicator light flashes rapidly, both buttons may be released. The rapid flashing indicates successful training.

Note: You may need to use a different method if you live in Canada or have difficulties programming your gate operator or garage door opener. See Gate Operator / Canadian Programming. 4. Press and hold the HomeLink button you programmed for two seconds, then release. You may need to do this twice to activate the door. If your garage door does not operate, watch the HomeLink indicator light.

If the indicator light stays on, the programming is complete. No further action is needed. If the indicator light flashes rapidly for 2
seconds and then turns to a constant light, the HomeLink button is not programmed yet. See Programming Your Garage Door Opener Motor.

158

Explorer (TUB), enUSA, First Printing

E142658E142659E142658Universal Garage Door Opener (If Equipped)

Gate Operator / Canadian Programming Canadian radio-frequency laws require transmitter signals to “time-out” (or quit) after several seconds of transmission – which may not be long enough for HomeLink to pick up the signal during programming. Similar to this Canadian law, some U.S. gate operators are designed to “time-out” in the same manner. Note: If programming a garage door opener or gate operator, it is advised to unplug the device during the “cycling” process to prevent possible overheating. 1. Press and hold the HomeLink button while you press and release,every two seconds, your hand-held transmitter until the HomeLink indicator light changes from a slow to a rapidly blinking light.

2. Release both the HomeLink and hand-held transmitter buttons.

3. Continue programing HomeLink. See

In-Vehicle Programming.

Erasing the Function Button Codes Note: You cannot erase individual buttons.

1. Press and hold the outer two function

buttons simultaneously for approximately 20 seconds until the indicator lights above the buttons flash rapidly.

2. When the indicator lights flash, release the buttons. The codes for all buttons are erased.

Reprogramming a Single Button To program a device to a previously trained button, follow these steps: 1. Press and hold the desired button. Do

NOT release the button.

2. The indicator light will begin to flash

after 20 seconds. Without releasing the button, follow Step 1 in the Programming section.

For questions or comments, contact HomeLink at www.homelink.com, www.youtube.com/HomeLinkGentex or 1-800-355-3515. Programming to a Genie Intellicode 2
Garage Door Opener Note: The Genie Intellicode 2 transmitter must already be programmed to operate with the garage door opener. Note: To program HomeLink to the transmitter you must first put the transmitter into programming mode.

159

Explorer (TUB), enUSA, First Printing

E142660Universal Garage Door Opener (If Equipped)

1. Press and hold the previously

programmed Genie button on the hand-held transmitter for 10 seconds. The indicator light will change from red to red and green.

2. Press the same button twice to confirm

the change. If done correctly the indicator light will turn green.

Programming HomeLink to the Genie Intellicode Garage Door Opener Motor Note: You may need a ladder to access the garage door opener motor.

1. Press and hold the program button on

the garage door opener motor until both blue indicator lights turn on.

2. Release the program button. Only the smaller round indicator light should be on.

3. Press and release the program button.

The larger purple indicator light will flash.

Note: The next two steps must be completed in 30 seconds. 4. Press and release the Genie Intellicode

2 hand-held transmitter’s previously programmed button. Both indicator lights on the garage door opener motor unit should now flash purple.

A. B.

Red indicator light Green indicator light

1. Press and hold one of the buttons on

the hand-held transmitter for 10
seconds. The indicator light will change from green to red and green.

2. Press the same button twice to confirm the change to programming mode. If done properly the indicator light will appear red.

3. Hold the transmitter within 1–3 inches (2–8 centimeters) of the button on the visor you want to program.

4. Press and hold both the programmed

Genie button on the hand-held transmitter and the button you want to program. The indicator light on the visor will flash rapidly when the programming is successful.

Note: The Genie transmitter will transmit for up to 30 seconds. If HomeLink does not program within 30 seconds the Genie transmitter will need to be pressed again. If the Genie transmitter indicator light displays green and red, release the button until the indicator light turns off before pressing the button again. Once HomeLink has been programmed successfully, the Genie transmitter must be changed out of program mode. To do this:

160

Explorer (TUB), enUSA, First Printing

BAE142661E142662Universal Garage Door Opener (If Equipped)

5. Press and hold the previously

programmed button on the visor for 2
seconds. Repeat this step up to 3 times until the garage door moves. Programming is now complete. Clearing a HomeLink Device To erase programming from the three HomeLink buttons press and hold the two outer HomeLink buttons until the indicator light begins to flash. The indicator light will begin flashing in 10 to 20 seconds, at which time both buttons should be released. Programming has now been erased, and the indicator light should blink slowly to indicate the device is in train mode when any of the three HomeLink buttons are pressed. FCC and RSS-210 Industry Canada Compliance This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications to your device not expressly approved by the party responsible for compliance can void the user’s authority to operate the equipment.

161

Explorer (TUB), enUSA, First Printing

Auxiliary Power Points

12 Volt DC Power Point WARNINGS

Do not plug optional electrical accessories into the cigar lighter socket. Incorrect use of the cigar

lighter can cause damage not covered by the vehicle warranty, and can result in fire or serious injury.

Do not use a power point for operating a cigar lighter. Incorrect use of the power points can cause

damage not covered by the vehicle warranty, and can result in fire or serious injury.

Note: When you switch the ignition on, you can use the socket to power 12 volt appliances with a maximum current rating of 15 amps. If the power supply does not work after you switch the ignition off, switch the ignition on. Note: Do not hang any accessory from the accessory plug. Note: Do not use the power point over the vehicle capacity of 12 volt DC 180 watts or a fuse may blow. Note: Always keep the power point caps closed when not in use. Do not insert objects other than an accessory plug into the power point. This will damage the power point and blow the fuse. Run the vehicle for full capacity use of the power point. To prevent the battery from running out of charge: • Do not use the power point longer than

necessary when the vehicle is not running.

• Do not leave devices plugged in

overnight or when you park your vehicle for extended periods.

Explorer (TUB), enUSA, First Printing

Locations Power points may be in the following locations: • On the lower instrument panel. • • On the rear of the center console. • 110 Volt AC Power Point (If Equipped)

Inside the center console.

In the rear cargo area.

WARNING

Do not keep electrical devices plugged in the power point whenever the device is not in use. Do not use any extension cord with the 110 volt AC power point, since it will defeat the safety protection design. Doing so may cause the power point to overload due to powering multiple devices that can reach beyond the 150 watt load limit and could result in fire or serious injury.

Note: The power point will turn off when the ignition is switched off or the battery voltage drops below 11 volts. Use the power point for powering electric devices that require up to 150 watts. It is on the rear of the center console.

Note: Depending on your vehicle, the power point cover may open to the right or upward.

162

E193395Auxiliary Power Points

When the indicator light on the power point is: • On: The power point is working, the ignition is on and a device is plugged in.

• Off: The power point is off, the ignition

is off or no device is plugged in. Flashing: The power point is in fault mode.

•

The power outlet temporarily turns off power when in fault mode if the device exceeds the 150 watt limit. Unplug your device and switch the ignition off. Switch the ignition back on, but do not plug your device back in. Let the system cool off and switch the ignition off to reset the fault mode. Switch the ignition back on and make sure the indicator light remains on. Do not use the power point for certain electric devices, including: • Cathode-ray, tube-type televisions. • Motor loads, such as vacuum cleaners, electric saws and other electric power tools or compressor-driven refrigerators.

• Measuring devices, which process

precise data, such as medical equipment or measuring equipment.

• Other appliances requiring an

extremely stable power supply such as microcomputer-controlled electric blankets or touch-sensor lamps.

163

Explorer (TUB), enUSA, First Printing

Storage Compartments

CENTER CONSOLE Stow items in the cup holder carefully as items may become loose during hard braking, acceleration or crashes, including hot drinks which may spill. Available console features include:

Rear Seat Armrest

OVERHEAD CONSOLE

Press near the rear edge of the door to open it.

USB, or USB and SD card (if equipped). Power point. Cup holder. Hill descent control (if equipped). 110 volt AC power point or USB port (if equipped). Rear climate controls (if equipped). 110 volt AC power point / 230
volt AC power point (if equipped). USB smart charger (if equipped).

164

Explorer (TUB), enUSA, First Printing

E193409E190042E75193Starting and Stopping the Engine

GENERAL INFORMATION

IGNITION SWITCH (If Equipped)

WARNINGS

Extended idling at high engine speeds can produce very high temperatures in the engine and

exhaust system, creating the risk of fire or other damage.

Do not park, idle or drive your vehicle on dry grass or other dry ground cover. The emission system heats up

the engine compartment and exhaust system, creating the risk of fire.

Do not start the engine in a closed garage or in other enclosed areas. Exhaust fumes can be toxic. Always open the garage door before you start the engine.

If you smell exhaust fumes inside your vehicle, have your vehicle checked by an authorized dealer immediately. Do not drive your vehicle if you smell exhaust fumes.

If you disconnect the battery, your vehicle may exhibit some unusual driving characteristics for approximately 5 miles (8 kilometers) after you reconnect it. This is because the engine management system must realign itself with the engine. You can disregard any unusual driving characteristics during this period. The powertrain control system meets all Canadian interference-causing equipment standard requirements regulating the impulse electrical field or radio noise. When you start the engine, avoid pressing the accelerator pedal before and during operation. Only use the accelerator pedal when you have difficulty starting the engine.

0 (off) - The ignition is off. Note: When you switch the ignition off and leave your vehicle, do not leave your key in the ignition. This could cause your vehicle battery to lose charge. I (accessory) - Allows the electrical accessories, such as the radio, to operate while the engine is not running. Note: Do not leave the ignition key in this position for too long. This could cause your vehicle battery to lose charge. II (on) - All electrical circuits are operational and the warning lamps and indicators illuminate. III (start) - cranks the engine. KEYLESS STARTING (If Equipped) Note: The keyless starting system may not function if the key is close to metal objects or electronic devices such as cellular phones. Note: A valid key must be located inside your vehicle to switch the ignition on and start the engine.

165

Explorer (TUB), enUSA, First Printing

E72128Starting and Stopping the Engine

Note: You can crank the engine for a total of 60 seconds without the engine starting before the starting system temporarily disables. The 60 seconds does not have to be all at once. For example, if you crank the engine three times for 20 seconds each time, without the engine starting, you reached the 60-second time limit. A message appears in the information display alerting you that you exceeded the cranking time. You cannot attempt to start the engine for at least 15 minutes. After 15
minutes, you are limited to a 15-second engine cranking time. You need to wait 60
minutes before you can crank the engine for 60 seconds again. Before starting your vehicle, check the following: • Make sure all occupants have fastened

their safety belts.

• Make sure the headlamps and electrical accessories are off.

• Make sure the parking brake is on. • Make sure the transmission is in park