Download PDF Manual

FLR: Distributes outside air through the floor vents. OFF: Outside air is shut out and the climate system is turned off. MIX: Distributes outside air through the windshield defroster vents and the floor vents.


: Distributes outside air through the windshield defroster vents.


Operating tips • To reduce fog build-up on the windshield during humid weather, place


the air flow selector in the


position.


• To reduce humidity build-up inside the vehicle during cold or warm weather, do not drive with the air flow selector in the OFF position. • Do not put objects under the front seats that will interfere with the air • Remove any snow, ice or leaves from the air intake area at the base of • A small amount of air may be felt from the floor vent regardless of the


flow to the back seats.


the windshield.


air distribution setting that is selected.


To aid in side window defogging/demisting in cold weather: 1. Select MIX. 2. Set the temperature control to maintain comfort. 3. Set the fan speed to HI. 48


2011 Econoline (eco) Owners Guide, 3rd Printing USA (fus)


Climate Controls


MANUAL HEATING AND AIR CONDITIONING SYSTEM (IF EQUIPPED) 1. Fan speed adjustment: Controls the volume of air circulated in the vehicle. 2. Temperature selection: Controls the temperature of the airflow in the vehicle. 3. Air flow selections: Controls the direction of the airflow in the vehicle. Also controls the airflow for the rear auxiliary system (if equipped). See the following for a brief description on each control. MAX A/C: Uses recirculated air to cool the vehicle. Air flows from the instrument panel vents only. If equipped with auxiliary A/C, auxiliary airflow will be from the rear headliner vents. NORM A/C: Uses outside air to cool the vehicle. Air flows from the instrument panel vents only. If equipped with auxiliary A/C, auxiliary airflow will be from the rear headliner vents. VENT: Distributes outside air through the instrument panel vents. OFF: Outside air is shut out and the climate system is turned off. FLR: Distributes outside air through the floor vents. If equipped with rear auxiliary heater or A/C, auxiliary airflow will be from the rear floor vents. MIX: Distributes outside air through the windshield defroster vents and floor vents. If equipped with rear auxiliary heater or A/C, auxiliary airflow will be from the rear floor vents.


: Distributes outside air through the windshield defroster vents. If equipped with rear auxiliary heater or A/C, auxiliary airflow will be from the rear floor vents.


the air flow selector in the


Operating tips • To reduce fog build-up on the windshield during humid weather, place • To reduce humidity build-up inside the vehicle: do not drive with the • Do not put objects under the front seats that will interfere with the • Remove any snow, ice or leaves from the air intake area at the base of


air flow selector in the OFF position.


airflow to the back seats.


position.


the windshield.


49


2011 Econoline (eco) Owners Guide, 3rd Printing USA (fus)


Climate Controls • A small amount of air may be felt from the floor vent regardless of the


air distribution setting that is selected.


During extreme high ambient temperatures when idling stationary for extended periods of time in gear, it is recommended to run the A/C in the MAX A/C position, turn off the rear A/C unit (if equipped), reduce blower fan speed from the highest setting and put the vehicle’s transmission into the PARK gear position to continue to receive cool air from your A/C system. To aid in side window defogging/demisting in cold weather: 1. Select MIX. 2. Set the temperature control to maintain comfort. 3. Set the fan speed to HI.


REAR FAN SPEED ADJUSTMENT (IF EQUIPPED) The rear fan controls adjust the volume of air circulated in the rear of the vehicle.


50


2011 Econoline (eco) Owners Guide, 3rd Printing USA (fus)


Lights


51


HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, license plate lamps and tail lamps.


Turns the headlamps on.


High beams • Push the lever toward the instrument panel to activate. • Pull the lever toward you to


deactivate.


Flash-to-pass Pull toward you slightly to activate and release to deactivate.


2011 Econoline (eco) Owners Guide, 3rd Printing USA (fus)


Lights


Daytime running lamps (DRL) (if equipped) Turns the headlamps on with a reduced output. To activate: • the ignition must be in the on position and • the headlamp control is in the off or parking lamp position.


WARNING: Always remember to turn on your headlamps at dusk or during inclement weather. The Daytime Running Lamp (DRL) system does not activate the tail lamps and generally may not provide adequate lighting during these conditions. Failure to activate your headlamps under these conditions may result in a collision.


PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel and all applicable switches in the vehicle during headlamp and parking lamp operation. • Move the control up or down to adjust the intensity of the panel lighting.


• Move the control to the full upright position, past detent, to turn on the interior lamps.


Note: If the battery is disconnected, discharged, or a new battery is installed, the dimmer switch requires re-calibration. Rotate the dimmer switch from the full dim position to the full dome/on position to reset. This will ensure that your displays are visible under all lighting conditions. The dome lamp will not illuminate if the control switch is not rotated past the detent.


52


2011 Econoline (eco) Owners Guide, 3rd Printing USA (fus)


Lights


ground


VERTICAL AND HORIZONTAL AIM ADJUSTMENT (SEALED BEAM HEADLAMPS) The headlamps on your vehicle are intended to be aimed using mechanical aimers. If mechanical aimers are used and the cross-car sight line is in any way blocked, set the legs of the universal adaptor all to the same setting, such that the cross-car sight line is no longer blocked, per the instructions for the brand of mechanical aimer used. You can also aim the headlamps visually using the procedure below. To adjust the headlamps: 1. Park your vehicle on a level surface about 25 feet (7.6 meters) away from a vertical plain surface (3). Check your headlamp alignment at night or in a dark area so that you can see the headlamp beam pattern. • (1) 8 feet (2.4 meters) • (2) Center height of lamp to • (3) 25 feet (7.6 meters) • (4) Horizontal reference line • (5) Center of headlamps • (6) Center line of the vehicle 2. The center of the headlamp is marked either on the lens (a circle or cross marker) or on the bulb shield, internal to the lamp (mark or feature). Measure the height from the center of your headlamp to the ground (2) and mark an 8 foot (2.4 meter) long horizontal line on the wall or screen (1) at this height (masking tape works well). 3. Turn on the low beam headlamps and open the hood. 4. Locate the high intensity area of the beam pattern and place the top edge of the intensity zone even with the horizontal reference line (4). If the top edge of the high intensity area is not even with the horizontal line, follow the next step to adjust it.


53


2011 Econoline (eco) Owners Guide, 3rd Printing USA (fus)


Lights


5. Locate the vertical adjuster (1) for each headlamp. Adjust the aim by turning the adjuster control either clockwise (to adjust up) or counterclockwise (to adjust down). 6. In addition to the horizontal line marked in step 2, a pair of vertical lines (5) must be marked at the center line of the headlamps on the wall or screen. 7. On the wall or screen, locate the high intensity area of the beam pattern. The left edge of the high intensity area should be even with the vertical line corresponding to the headlamp under adjustment. If the left edge of the high intensity area is not even with the vertical line, follow the next step to adjust it. 8. Locate the horizontal adjuster (2) for each headlamp. Turn it clockwise or counterclockwise, to place the left edge of the high intensity area even with the vertical line corresponding to the headlamp under adjustment.


ground


VERTICAL AIM ADJUSTMENT (AERODYNAMIC HEADLAMPS) The headlamps on your vehicle can only be vertically adjusted. Your vehicle does not require horizontal aim adjustments. To adjust the headlamps: 1. Park the vehicle directly in front of a wall or screen on a level surface, approximately 25 feet (7.6 meters) away. • (1) 8 feet (2.4 meters) • (2) Center height of lamp to • (3) 25 feet (7.6 meters) • (4) Horizontal reference line 2. Measure the height from the center of your headlamp (indicated by a 3.0 mm circle on the lens) to the ground and mark an 8 foot (2.4 meter) horizontal reference line on the vertical wall or screen at this height (a piece of masking tape works well). 54


2011 Econoline (eco) Owners Guide, 3rd Printing USA (fus)


Lights


3. Turn on the low beam headlamps to illuminate the wall or screen and open the hood. Cover one of the headlamps so no light hits the wall. 4. On the wall or screen you will observe a light pattern with a distinct horizontal edge towards the right. If this edge is not at the horizontal reference line, the beam will need to be adjusted so the edge is at the same height as the horizontal reference line. 5. Locate the vertical adjuster on the back of each headlamp, then use a long Phillips #2 screwdriver to turn the adjuster either counterclockwise (to adjust down) or clockwise (to adjust up) aligning the upper edge of the light pattern up to the horizontal line. 6. Repeat step 3–5 for the other headlamp. 7. Close the hood and turn off the lamps.


TURN SIGNAL CONTROL • Push down to activate the left • Push up to activate the right turn


turn signal.


signal.


55


2011 Econoline (eco) Owners Guide, 3rd Printing USA (fus)


Lights


INTERIOR LAMPS


Dome lamps with rear headliner (if equipped) Dome lamps equipped with an on/off control will light when: • doors are closed and the control • control is in the middle position • headlamp control is rotated fully


is in the D position


and any door is open


counterclockwise


position, it will not illuminate when you


When the control is in the open the doors or fully rotate the headlamp control. Cargo lamps The dome portion of the cargo lamp, the center light, can be turned on when the headlamp control is rotated fully counterclockwise or when any door is opened.


With the ignition key in the accessory or on position, the rear lamp can be turned on or off by sliding the control.


Front and rear courtesy/reading lamps (if equipped) The dome portion of the lamp, the center light, can be turned on when the headlamp control is rotated fully counterclockwise or when any door is opened. The reading lamp portion, the two outer lights, can only be toggled on and off at the lamp.


56


2011 Econoline (eco) Owners Guide, 3rd Printing USA (fus)


Lights


BULB REPLACEMENT


Lamp assembly condensation Exterior lamps are vented to accommodate normal changes in pressure. Condensation can be a natural by-product of this design. When moist air enters the lamp assembly through the vents, there is a possibility that condensation can occur when the temperature is cold. When normal condensation occurs, a thin film of mist can form on the interior of the lens. The thin mist eventually clears and exits through the vents during normal operation. Clearing time may take as long as 48 hours under dry weather conditions. Examples of acceptable condensation are: • Presence of thin mist (no streaks, drip marks or droplets) • Fine mist covers less than 50% of the lens Examples of unacceptable moisture (usually caused by a lamp water leak) are: • Water puddle inside the lamp • Large water droplets, drip marks or streaks present on the interior of


the lens


Take your vehicle to a dealer for service if any of the above conditions of unacceptable moisture are present.


Using the right bulbs Replacement bulbs are specified in the chart below. Headlamp bulbs must be marked with an authorized “D.O.T.” for North America and an “E” for Europe to ensure lamp performance, light brightness and pattern and safe visibility. The correct bulbs will not damage the lamp assembly or void the lamp assembly warranty and will provide quality bulb burn time.


Function


Number of


bulbs


Trade number


Headlamps (aerodynamic) Headlamps (sealed beam) Park lamp with aerodynamic


H13/9008


H6054


3157A or 3157AK


57


2011 Econoline (eco) Owners Guide, 3rd Printing USA (fus)


Lights


Function


Number of


bulbs


Trade number


194


168


3157K


Park lamp with sealed beam Side marker with aerodynamic Side marker with sealed beam Back-up lamps License plate lamp Stop/tail/turn/side marker lamp High-mount brake lamp Cargo lamp Dome lamp (standard) Map/reading lamp All replacement bulbs are clear in color except where noted. To replace all instrument panel lights - see your authorized dealer


912
211-2
912
211-2


3156K or 3156


3157K


168


Replacing exterior bulbs Check the operation of all bulbs frequently. Replacing headlamp bulbs (aerodynamic) 1. Make sure the headlamp switch is in the off position, then open the hood. 2. Remove the three screws from the headlamp assembly and pull the assembly straight out. 3. Disconnect the electrical connector by squeezing the release tab and pushing the connector forward, then pulling it rearward.


58


2011 Econoline (eco) Owners Guide, 3rd Printing USA (fus)


4. Remove the bulb assembly by turning it counterclockwise and pulling it straight out.


Lights


WARNING: Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated.


Note: If the bulb is accidentally touched, it should be cleaned with alcohol before being used. To install the new bulb, follow the removal procedures in reverse order.


Replacing headlamps (sealed beam) 1. Make sure the headlamp switch is in the off position, then open the hood. 2. Remove the four screws from the headlamp assembly and carefully remove the lamp/bezel. 3. Remove the four screws and the retaining ring. 4. Disconnect the electrical connector from the lamp and remove the lamp. To install the new lamp, follow the removal procedures in reverse order. Replacing front parking lamp/turn signal bulbs 1. Make sure the headlamp control is in the off position. 2. Remove the headlamp assembly. Refer to Replacing headlamp bulbs in this section.


59


2011 Econoline (eco) Owners Guide, 3rd Printing USA (fus)


Lights


Aerodynamic


Sealed beam


3. Rotate the bulb socket counterclockwise and remove. 4. Carefully pull the bulb straight out of the socket. To complete installation, follow the removal procedures in reverse order. Replacing side marker bulbs 1. Make sure the headlamp control is in the off position. 2. Remove the headlamp assembly. Refer to Replacing headlamp bulbs in this section. Aerodynamic


60


2011 Econoline (eco) Owners Guide, 3rd Printing USA (fus)


Sealed beam


Lights


3. Rotate the bulb socket counterclockwise and remove. 4. Carefully pull the bulb straight out of the socket. To complete installation, follow the removal procedures in reverse order. Replacing high-mount brake lamp bulbs On vehicles without a rear headliner, the interior cargo lamp (if equipped) must be removed from under the high-mount brake lamp assembly located inside the vehicle. Then, do the following: 1. Remove the two screws from the high-mount brake lamp assembly and lift the lamp from the vehicle. 2. Remove the bulb socket from the lamp assembly by turning it counterclockwise. 3. Carefully pull the bulb straight out of the socket.


To install the new bulb, follow the removal procedure in reverse order.


61


2011 Econoline (eco) Owners Guide, 3rd Printing USA (fus)


Lights


Replacing license plate lamp bulbs 1. Turn the headlamp switch to the off position. 2. Remove the two screws and the license plate lamp assembly from the rear door. 3. Remove bulb socket from lamp assembly by turning it counterclockwise. 4. Pull the bulb out from socket and push in the new bulb.


To install the new bulb, follow the removal procedures in reverse order. Replacing stop/turn/tail/side marker/backup lamp bulbs The stop/turn/tail/side marker/backup lamp bulbs are located in the tail lamp assembly. Follow the same steps to replace any of the bulbs: 1. Turn the headlamp switch to the off position, then remove the four screws and the lamp assembly from the vehicle.


2. Rotate the bulb socket counterclockwise and remove it from lamp assembly. 3. Carefully pull the bulb straight out of the socket and push in the new bulb.


To install the lamp, follow the removal procedures in reverse order. 62


2011 Econoline (eco) Owners Guide, 3rd Printing USA (fus)


Driver Controls


MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you to increase the speed of the wipers; rotate towards you to decrease the speed of the wipers.


Windshield washer: Press the end of the stalk: • briefly: causes a single swipe of the wipers without washer fluid. • a quick press and hold: the


wipers will swipe three times with washer fluid. • a long press and hold: the wipers and washer fluid will be activated for up to ten seconds.


Courtesy wipe feature: One extra wipe will occur a few seconds after washing the front window to clear any excess washer fluid remaining on the windshield. Note: Do not operate the washer when the washer reservoir is empty. This may cause the washer pump to overheat. Check the washer fluid level frequently. Do not operate the wipers when the windshield is dry. This may scratch the glass, damage the wiper blades and cause the wiper motor to burn out. Before operating the wiper on a dry windshield, always use the windshield washer. In freezing weather, be sure the wiper blades are not frozen to the windshield before operating the wipers.


63


2011 Econoline (eco) Owners Guide, 3rd Printing USA (fus)


Driver Controls


TILT STEERING WHEEL To adjust the steering wheel: 1. Pull and hold the steering wheel release control toward you. 2. Move the steering wheel up or down until you find the desired location. 3. Release the steering wheel release control. This will lock the steering wheel in position.


WARNING: Never adjust the steering wheel when the vehicle is moving.


ILLUMINATED VISOR MIRROR (IF EQUIPPED) Lift the mirror cover to turn on the visor mirror lamp.


AUXILIARY POWER POINT (12V DC) Power outlets are designed for accessory plugs only. Do not insert any other object in the power outlet as this will damage the outlet and blow the fuse. Do not hang any type of accessory or accessory bracket from the plug. Improper use of the power outlet can cause damage not covered by your warranty. Auxiliary power points can be found in the following locations: • On the instrument panel, equipped with a cover or a cap plug • Behind the driver’s seat on the upper trim panel (if equipped) • In the glove box (if equipped) Do not use the power point for operating the cigarette lighter element (if equipped). 64


2011 Econoline (eco) Owners Guide, 3rd Printing USA (fus)


Driver Controls


Note: Do not plug optional electrical accessories into the cigarette lighter socket (if equipped). Improper use of the lighter can cause damage not covered by your warranty, and can result in fire or serious injury. To prevent the fuse from being blown, do not use the power point(s) over the vehicle capacity of 12V DC/180W. If the power point is not working, a fuse may have blown. Refer to Fuses and relays in the Roadside Emergencies chapter for information on checking and replacing fuses. To have full capacity usage of your power point, the engine is required to be running to avoid unintentional discharge of the battery. To prevent the battery from being discharged: • do not use the power point longer than necessary when the engine is • do not leave battery chargers, video game adapters, computers and other devices plugged in overnight or when the vehicle is parked for extended periods.


not running,


Always keep the power point caps closed when not being used.


POWER WINDOWS (IF EQUIPPED)


WARNING: Do not leave children unattended in the vehicle and do not let children play with the power windows. They may


seriously injure themselves.


WARNING: When closing the power windows, you should verify they are free of obstructions and ensure that children and/or


pets are not in the proximity of the window openings.


Press and pull the window switches to open and close windows. • Press down (to the first detent) • Pull up (to the first detent) and


and hold the switch to open.


hold the switch to close.


65


2011 Econoline (eco) Owners Guide, 3rd Printing USA (fus)


Driver Controls


One-touch down Allows the driver’s window to open fully without holding the control down. Press the switch completely down to the second detent and release quickly. The window will open fully. Momentarily press the switch to any position to stop the window operation.


Accessory delay With accessory delay, the window switches and radio may be used for up to 10 minutes after the ignition switch is turned to the off position, or until any door is opened.


INTERIOR MIRROR The interior rear view mirror has two pivot points on the support arm which lets you adjust the mirror up or down and from side to side.


WARNING: Do not adjust the mirror while the vehicle is in motion.


Automatic dimming interior rear view mirror (if equipped) The interior rear view mirror has an auto-dimming function. The electronic day/night mirror will change from the normal (high reflective) state to the non-glare (darkened) state when bright lights (glare) reach the mirror. When the mirror detects bright light from behind the vehicle, it will automatically adjust (darken) to minimize glare. The mirror will automatically return to the normal state whenever the vehicle is placed in R (Reverse) to ensure a bright clear view when backing up. Do not block the sensors on the front and back of the interior rear view mirror since this may impair proper mirror performance. Note: A rear center passenger and/or raised rear center headrest (if equipped) may also block the light from reaching the sensor. Do not clean the housing or glass of any mirror with harsh abrasives, fuel or other petroleum-based cleaning products. Note: If equipped with a rearview camera system, a video image will display in the mirror or the navigation system display (if equipped) when the vehicle is put in R (Reverse). As you shift into any other gear from R (Reverse), the image will remain for a few seconds and then turn off. Refer to Rearview camera system in the Driving chapter. 66


2011 Econoline (eco) Owners Guide, 3rd Printing USA (fus)


Driver Controls


EXTERIOR MIRRORS


Power side view mirrors (if equipped)


WARNING: Do not adjust the mirror while the vehicle is in motion.


To adjust your mirrors: 1. Rotate the control clockwise to adjust the right mirror and rotate the control counterclockwise to adjust the left mirror. 2. Move the control in the direction you wish to tilt the mirror. 3. Return to the center position to lock mirrors in place.


Spotter mirror (if equipped) Note: New spotter mirrors may be stiff, requiring several cycles before the spotter adjustment effort eases. Spotter mirror on standard mirror (if equipped) The spotter mirror only can be tilted from top to bottom. Move the lower mirror manually up/down to increase side and rear visibility. Apply pressure only in the center of the spotter mirror along the top or bottom edges to adjust the tilt feature. Do not apply any force on the left or right edges of the standard mirror spotter section, as this may lead to a mirror fracture.


67


2011 Econoline (eco) Owners Guide, 3rd Printing USA (fus)


Driver Controls


Spotter mirror on telescoping mirror (if equipped) The spotter mirror has a swivel that allows it to tilt up and down, and also to tilt left and right to increase side and rear visibility.


Fold-away mirrors The mirrors can be manually folded forward or backwards for narrow spaces like driving through an automatic car wash or backing out of a garage with the trailer tow mirror.


The telescoping feature (if equipped) allows the mirror to extend approximately 3.15 inches (80 mm). This feature is especially useful to the driver when towing a trailer.


Blind spot mirrors (if equipped) Your vehicle may be equipped with blind spot mirrors. Refer to Blind spot mirrors in the Driving chapter. 68


2011 Econoline (eco) Owners Guide, 3rd Printing USA (fus)


Driver Controls


SPEED CONTROL (IF EQUIPPED) With speed control set, you can maintain a set speed without keeping your foot on the accelerator pedal.


WARNING: Do not use the speed control in heavy traffic or on roads that are winding, slippery or unpaved.


Using speed control The speed controls are located on the steering wheel. The following buttons work with speed control. ON: Press to turn on speed control. OFF: Press to turn off speed control. RES (Resume): Press to resume a set speed. SET/ACCEL: Press to set a speed or increase a set speed. COAST: Press to reduce a set speed. Setting speed control 1. Press and release ON. 2. Accelerate to the desired speed. 3. Press and release SET/ACCEL. 4. Take your foot off the accelerator pedal. 5. The indicator Note: • Vehicle speed may vary momentarily when driving up and down a • If the vehicle speed increases above the set speed on a downhill, you • If the vehicle speed decreases more than 10 mph (16 km/h) below


may want to apply the brakes to reduce the speed.


light on the instrument cluster will turn on.


steep hill.


your set speed on an uphill, your speed control will disengage.


Disengaging speed control To disengage speed control, press the brake pedal. Disengaging speed control will not erase the previous set speed.


69


2011 Econoline (eco) Owners Guide, 3rd Printing USA (fus)


Driver Controls


Resuming a set speed Press and release RES. This will automatically return the vehicle to the previously set speed. Increasing speed while using speed control To increase the set speed: • Press and hold SET/ACCEL until you get to the desired speed, then release. You can also use SET/ACCEL to operate the tap-up function. Press and release SET/ACCEL to increase the vehicle set speed in 1 mph (1.6 km/h) increments. • Use the accelerator pedal to get to the desired speed. When the


vehicle reaches that speed, press and release SET/ACCEL.


Reducing speed while using speed control To reduce the set speed: • Press and hold COAST until you get to the desired speed, then


release. You can also use COAST to operate the tap-down function. Press and release COAST to decrease the vehicle set speed in 1 mph (1.6 km/h) increments. • Press the brake pedal until the desired vehicle speed is reached, then


press and release SET/ACCEL.


Turning off speed control To turn off the speed control, press OFF or turn off the ignition. Note: When you turn off the speed control or the ignition, your speed control set speed memory is erased.


STEERING WHEEL CONTROLS (IF EQUIPPED) SYNC威 system hands free control feature (if equipped) Press briefly to use the voice command feature. You will hear a tone and LISTENING will appear in the radio display. Press and hold Press hold For further information on the SYNC威 system, refer to the SYNC威 supplement. 70


to activate phone mode or answer a phone call. Press and to end a call or exit phone mode.


to exit voice command.


2011 Econoline (eco) Owners Guide, 3rd Printing USA (fus)


Driver Controls


control briefly until the icon appears on the


Navigation system/SYNC威 hands free control features (if equipped) Press voice Navigation display to use the voice command feature. Press hold For further information on the Navigation system/SYNC威 system, refer to the Navigation System and SYNC威 supplements.


to activate phone mode or answer a phone call. Press and to exit phone mode or end a call.


UPFITTER CONTROLS (IF EQUIPPED) Your vehicle may be equipped with the Upfitter option package which will provide four switches, mounted in the center of the instrument panel, labeled AUX 1, AUX 2, AUX 3
and AUX 4. These switches will only operate while the ignition is in the on position, whether the engine is running or not. It is, however, recommended that the engine remain running to maintain battery charge when using the Upfitter switches for extended duration or higher current draws. When switched on by the operator they provide 10 amps, 15 amps or 30 amps of electrical battery power for a variety of personal or commercial uses. If your vehicle is equipped with this option, a relay/fuse kit will be included. This kit contains the required fuses and relays that need to be installed into the Power Distribution Box located under the hood. Refer to the instruction sketch included in the kit and Fuses and Relays in the Roadside Emergencies chapter. See your authorized dealer for service. There will also be one power lead for each switch found as a blunt-cut and sealed wire located in the underhood cowl shield above the engine block PCM.


71


2011 Econoline (eco) Owners Guide, 3rd Printing USA (fus)


Driver Controls


They are coded as follows:


Switch


Circuit number Wire color


AUX 1
AUX 2


AUX 3


CAC05
CAC06


CAC07


Yellow Green with Brown Trace Violet with Green Trace Brown


Fuse 30A 30A


10A


AUX 4
15A More detailed information about Upfitter switches can be found at https://www.fleet.ford.com/truckbbas/.


CAC08


POSITIVE RETENTION FLOOR MAT (IF EQUIPPED)


WARNING: Do not install additional floor mats on top of the factory installed floor mats as they may interfere with the


accelerator or the brake pedals.


Position the floor mat so that the eyelets are over the retention posts and press down to lock in. Make sure that the mat does not interfere with the operation of the accelerator or the brake pedal. To remove the floor mat, reverse the installation procedure.


72


2011 Econoline (eco) Owners Guide, 3rd Printing USA (fus)


Locks and Security


KEYS The key operates all locks on your vehicle. You should always carry a second key with you in a safe place in case you require it in an emergency. If your vehicle is equipped with the SecuriLock威 passive anti-theft system, your keys are electronically coded to your vehicle; using a non-coded key will not permit your vehicle to start. If you lose your dealer supplied keys, replacement keys are available through your authorized dealer.


POWER DOOR LOCKS (IF EQUIPPED) Press control to unlock all doors.


Press control to lock all doors.


Memory lock If you lock your doors with the power lock switch or the remote transmitter while the sliding door is open, the door will automatically lock after it is closed.


Autolock feature Note: Your vehicle comes with the autolock feature disabled. The autolock feature will lock all the doors when: • all the doors are closed, • the ignition is in the on position, • you shift into any gear putting the vehicle in motion, and • the vehicle attains a speed greater than 12 mph (20 km/h) for greater


than two seconds.


73


2011 Econoline (eco) Owners Guide, 3rd Printing USA (fus)


Locks and Security


The autolock feature repeats when: • any door is opened then closed while the ignition is in the on position • the vehicle then attains a speed greater than 12 mph (20 km/h) for


and the vehicle speed is 9 mph (15 km/h) or lower, and


greater than two seconds.


Deactivating/activating autolock feature Your vehicle comes with the autolock feature disabled; there are three methods to enable/disable this feature: • Through your authorized dealer, or • by using a power door unlock/lock procedure, or • by using the instrument cluster message center (if equipped). Refer to


Message center in the Instrument Cluster chapter.


Note: The autolock feature can be activated/deactivated independently of the autounlock feature. Power door lock switch autolock enable/disable procedure Before starting, ensure the ignition is in the off position and all vehicle doors are closed. You must complete Steps 1–5 within 30 seconds or the procedure will have to be repeated. If the procedure needs to be repeated, wait a minimum of 30 seconds before beginning again. 1. Place the key in the ignition and turn the ignition to the on position. 2. Press the power door unlock control on the door panel three times. 3. Turn the ignition from the on position to the off position. 4. Press the power door unlock control on the door panel three times. 5. Turn the ignition back to the on position. The horn will chirp one time to confirm programming mode has been entered and is active. 6. To enable/disable the autolock feature, press the unlock control, then press the lock control. The horn will chirp once if autolock was deactivated or twice (one short and one long chirp) if autolock was activated. 7. Turn the ignition to the off position. The horn will chirp once to confirm the procedure is complete. 74


2011 Econoline (eco) Owners Guide, 3rd Printing USA (fus)


Locks and Security


Autounlock feature After the autolock feature has locked the doors, the autounlock feature will unlock all the doors when: • the vehicle has then come to a stop and the ignition is turned off or to • the driver door is opened within 10 minutes of the ignition being


accessory; and


turned off or to accessory.


Note: The doors will not autounlock if the vehicle has been electronically locked before the driver door is opened. Deactivating/activating autounlock feature Your vehicle comes with the autounlock features disabled; there are three methods to enable/disable this feature: • Through your authorized dealer, or • by using a power door unlock/lock sequence, or • by using the instrument cluster message center (if equipped). Refer to


Message center in the Instrument Cluster chapter.


Note: The autounlock feature can be activated/deactivated independently of the autolock feature. Power door lock switch autounlock enable/disable procedure Before starting, ensure the ignition is off and all vehicle doors are closed. You must complete Steps 1–5 within 30 seconds or the procedure will have to be repeated. If the procedure needs to be repeated, wait a minimum of 30 seconds before beginning again. 1. Turn the ignition on. 2. Press the power door unlock control on the door panel three times. 3. Turn the ignition off. 4. Press the power door unlock control on the door panel three times. 5. Turn the ignition back on. The horn will chirp one time to confirm programming mode has been entered and is active. 6. To enable/disable the autounlock feature, press the lock control, then press the unlock control. The horn will chirp once if autounlock was deactivated or twice (one short and one long chirp) if autounlock was activated.


75


2011 Econoline (eco) Owners Guide, 3rd Printing USA (fus)


Locks and Security


7. Turn the ignition off. The horn will chirp once to confirm the procedure is complete.


Back cargo door lock (if equipped) The passenger side rear cargo door has a power door lock control mounted on the inside of the door. When this lock is pressed, all doors will lock/unlock.


or manual door locks.


E-Guard Cargo Protection System™ (if equipped) The E-Guard Cargo Protection System™ insures that the side and cargo doors are double locked for extra security. E-Guard Cargo Protection System™ features • The E-Guard Cargo Protection System™ is available with either power • The E-Guard Cargo Protection System™ provides extra security via a • The cargo doors can only be unlocked from the outside by using the • The power unlock feature (if equipped with power door locks) will • The E-Guard Cargo Protection System™ is equipped with an emergency unlock handle installed in the door inner panel.


only unlock the front doors.


double-locked design.


keys.


E-Guard Cargo Protection System™ procedure For vehicles equipped with power door locks: • Lock the vehicle with the key, manual door lock, key fob or use the power door lock on the front door trim panel. The front doors are locked and the cargo doors are double-locked.


• Unlock the vehicle with the key fob or use the power door lock on the front door. The front doors are unlocked and the cargo doors remain double-locked.


76


2011 Econoline (eco) Owners Guide, 3rd Printing USA (fus)


• The only way to unlock the side or back cargo doors from


outside vehicle is with the key.


Locks and Security


manual door lock.


For vehicles equipped with manual door locks: • The front door locks can be locked by using either the key or the • In order to activate the E-Guard Cargo Protection System™, use the key or the manual door lock to lock the side and back cargo doors. • The cargo doors cannot be unlocked using the manual door


lock.


WARNING: If equipped with E-Guard Cargo Protection System™ occupants may become trapped in the cargo area unless the exit procedure is followed. The cargo doors cannot be unlocked using manual or power door locks or key fob. In an emergency, to exit the cargo area, locate the emergency handle in the rear door or side door, pull the emergency handle to unlock the door, then unlatch the door using the inside release handle.


Emergency lock release The emergency handle in the door trim panel unlocks the E-Guard Cargo Protection System™. The emergency handles are located in the following areas: • The side door emergency handle is located on the door inner trim panel in the speaker cup.


77


2011 Econoline (eco) Owners Guide, 3rd Printing USA (fus)


Locks and Security • The rear door handle is located in


the rear door below the glass.


To open the side or back cargo doors from the inside: 1. Unlock the E-Guard Cargo Protection System™ using the emergency handle. 2. Unlatch the door using the inside release handle.


REMOTE ENTRY SYSTEM (IF EQUIPPED) This device complies with part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. The typical operating range for your remote entry transmitter is approximately 33 feet (10 meters). A decrease in operating range could be caused by: • weather conditions, • nearby radio towers, • structures around the vehicle, or • other vehicles parked next to your vehicle.


78


2011 Econoline (eco) Owners Guide, 3rd Printing USA (fus)


Locks and Security


The remote entry system allows you to lock or unlock all vehicle doors without a key. Note: The lock and unlock features work when the ignition is in any position. The panic feature is active regardless of the ignition positions. If there are problems with the remote entry system, make sure to take ALL remote entry transmitters with you to the authorized dealer in order to aid in troubleshooting the problem. Note: If the vehicle is equipped with the E-Guard Cargo Protection System™ the remote transmitter Unlock command will only unlock the front doors; the only way to unlock the side or rear cargo doors from outside the vehicle is with the key.


and release again within three seconds to unlock the


Two step door unlocking and release to unlock the driver’s door. Note: The interior 1. Press lamps will illuminate if the control on the overhead lamp is not set to the off position. 2. Press passenger doors and the rear cargo doors. The battery saver feature will turn off the interior lamp 10 minutes after the ignition is turned to the off position. One step door unlocking and release If the one step door unlocking feature is activated, press once to unlock the passenger doors and the rear cargo doors. Note: The interior lamps will illuminate (refer to the Illuminated entry feature later in this section), if the control on the overhead lamp is not set to the off position.


79


2011 Econoline (eco) Owners Guide, 3rd Printing USA (fus)


Locks and Security


Switching from two step to one step door unlocking Your vehicle comes with two step unlocking enabled. With the vehicle locked, unlocking can be switched between two step and one step door unlocking by pressing and holding both the simultaneously on the remote entry transmitter for approximately four seconds and release. The park lamps will flash twice to indicate that the vehicle has switched to one step unlocking. Repeat the procedure to switch back to two-step unlocking.


buttons


and


and release to lock all the doors. If all doors are closed the


Locking the doors 1. Press parking lamps illuminate. and release again within three seconds to confirm that all 2. Press the doors are closed and locked. Note: The doors will lock again, the turn lamps will flash and the horn will chirp once. If any door is ajar the lamps will not flash and the horn will chirp twice.


Car finder twice within three seconds. The horn will chirp and the turn Press lamps will flash. It is recommended that this method be used to locate your vehicle, rather than using the panic alarm.


Sounding a panic alarm Press ignition to the accessory or on position to deactivate the alarm. Note: The panic alarm will operate regardless of the ignition position.


to activate the alarm. Press the control again, or turn the


Replacing the battery The remote entry transmitter uses one coin type three-volt lithium battery CR2032 or equivalent.


80


2011 Econoline (eco) Owners Guide, 3rd Printing USA (fus)


Locks and Security


To replace the battery: 1. Twist a thin coin between the two halves of the remote entry transmitter near the key ring. DO NOT TAKE THE RUBBER COVER AND CIRCUIT BOARD OFF THE FRONT HOUSING OF THE REMOTE ENTRY TRANSMITTER.


2. Do not wipe off any grease on the battery terminals on the back surface of the circuit board. 3. Remove the old battery. Note: Please refer to local regulations when disposing of transmitter batteries. 4. Insert the new battery. Refer to the diagram inside the remote entry transmitter for the correct orientation of the battery. Press the battery down to ensure that the battery is fully seated in the battery housing cavity. 5. Snap the two halves back together. Note: Replacement of the battery will not cause the remote transmitter to become deprogrammed from your vehicle. The remote transmitter should operate normally after battery replacement.


Replacing lost remote entry transmitters If you would like to have your remote entry transmitter reprogrammed because you lost one, or would like to buy additional remote entry transmitters, you can either reprogram them yourself, or take all remote entry transmitters to your authorized dealer for reprogramming. How to reprogram your remote entry transmitters You must have all remote entry transmitters (maximum of four) available before beginning this procedure. If all remote entry transmitters are not present during programming procedure, the ones missing during programming will no longer operate the vehicle.


81


2011 Econoline (eco) Owners Guide, 3rd Printing USA (fus)


Locks and Security


Note: Ensure the brake pedal is not depressed during this sequence. To reprogram the remote entry transmitters: 1. Ensure the vehicle is electronically unlocked. 2. Place the key in the ignition and turn from the 2 (lock) position to 3
(off). 3. Cycle eight times rapidly (within 10 seconds) between the 3 (off) position and 4 (on). Note: The eighth turn must end in the 4 (on) position. 4. The doors will lock, then unlock, to confirm that the programming mode has been activated. 5. Within 20 seconds press any button on the remote entry transmitter. Note: If more than 20 seconds have passed you will need to start the procedure over again. 6. The doors will lock, then unlock, to confirm that this remote entry transmitter has been programmed. 7. Repeat step 5 to program each additional remote entry transmitter (up to four transmitters). 8. Turn the ignition to the 3 (off) position after you have finished programming all of the remote entry transmitters. 9. The doors will lock, then unlock, to confirm that the programming mode has been exited.


Illuminated entry The interior lamps and parking lamps illuminate when the remote entry system is used to unlock the door(s) or sound the personal alarm. The illuminated entry system will turn off the lights if: • the ignition switch is turned to the on or accessory position, or • the remote transmitter lock control is pressed, or • after 25 seconds of illumination. The dome lamp control (if equipped) must not be set to the off position for the illuminated entry system to operate.


82


2011 Econoline (eco) Owners Guide, 3rd Printing USA (fus)


Locks and Security


The interior lamps will not turn off if: • they have been turned on with the dimmer control, or • any door is open.


SECURILOCK姞 PASSIVE ANTI-THEFT SYSTEM (IF EQUIPPED) SecuriLock威 passive anti-theft system is an engine immobilization system. This system is designed to help prevent the engine from being started unless a coded key programmed to your vehicle is used. The use of the wrong type of coded key may lead to a “no-start” condition. Your vehicle comes with two coded keys; additional coded keys may be purchased from your authorized dealer. The authorized dealer can program your spare keys to your vehicle or you can program the keys yourself. Refer to Programming spare keys for instructions on how to program the coded key. Note: The SecuriLock威 passive anti-theft system is not compatible with non-Ford aftermarket remote start systems. Use of these systems may result in vehicle starting problems and a loss of security protection. Note: Large metallic objects, electronic devices that are used to purchase gasoline or similar items, or a second coded key on the same key chain may cause vehicle starting issues. You need to prevent these objects from touching the coded key while starting the engine. These objects will not cause damage to the coded key, but may cause a momentary issue if they are too close to the key when starting the engine. If a problem occurs, turn the ignition off, remove all objects on the key chain away from the coded key and restart the engine. Note: Do not leave a duplicate coded key in the vehicle. Always take your keys and lock all doors when leaving the vehicle.


83


2011 Econoline (eco) Owners Guide, 3rd Printing USA (fus)


Locks and Security


Anti-theft indicator The anti-theft indicator is located in the instrument cluster. Vehicles equipped with the SecuriLock威 Passive Anti-theft system behave as follows: • When the ignition is in the off


position, the indicator will flash once every two seconds for a total of 10 seconds to indicate the SecuriLock威 system is functioning as a theft deterrent. • When the ignition is in the on position, the indicator will glow for three seconds to indicate a programmed key has been validated and the SecuriLock威 Passive Anti-theft system has enabled the engine. Vehicles without the SecuriLock威 Passive Anti-theft system behave as follows: • When the ignition is in the off position, the indicator will not flash. • When the ignition is in the on position, the indicator will glow for


three seconds to indicate the engine is enabled.


Automatic arming The vehicle is armed immediately after switching the ignition to the off position.


Automatic disarming Switching the ignition to the on position with a coded key disarms the vehicle.


Replacement keys If your keys are lost or stolen and you don’t have an extra coded key, you will need to have your vehicle towed to an authorized dealer. The key codes need to be erased from your vehicle and new coded keys will need to be programmed. Replacing coded keys can be very costly. Store an extra programmed key away from the vehicle in a safe place to help prevent any inconveniences. Please visit an authorized dealer to purchase additional spare or replacement keys.


Programming spare keys You can program your own coded keys to your vehicle. Please read and understand the entire procedure before you begin. 84


2011 Econoline (eco) Owners Guide, 3rd Printing USA (fus)


Locks and Security


Tips: • A maximum of eight keys can be coded to your vehicle. • Only use SecuriLock威 keys. • You must have two previously programmed coded keys (keys that already operate your vehicle’s engine) and the new unprogrammed key(s) readily accessible.


• If no previously programmed coded keys are available, you must take your vehicle to your authorized dealer to have the spare key(s) programmed.


1. Insert a previously programmed coded key into the ignition. 2. Turn the ignition from the 2 (lock) position to the 4 (on) position. Keep the ignition in the 4 (on) position for at least one second, but no more than 10 seconds. 3. Turn the ignition to the 2 (lock) position, and remove the coded key from the ignition. 4. After three seconds but within 10 seconds of removing the previously programmed coded key, insert the other previously programmed coded key into the ignition. 5. Turn the ignition from the 2 (lock) position to the 4 (on) position. Keep the ignition in the 4 (on) position for at least one second but not more than 10 seconds. 6. Turn the ignition to the 2 (lock) position, and remove the second key from the ignition. 7. After three seconds but within 20 seconds of removing the previously programmed coded key, insert the unprogrammed key into the ignition. 8. Turn the ignition from the 2 (lock) position to the 4 (on) position. Keep the ignition in the 4 (on) position for at least one second. 9. Your new key is now programmed. If the key has been successfully programmed it will start the vehicle’s engine and the theft indicator light will illuminate for three seconds and then go out. If the key was not successfully programmed, it will not start your vehicle’s engine and the theft indicator light will flash on and off rapidly. If failure repeats, bring your vehicle to your authorized dealer to have the new key(s) programmed. To program additional new unprogrammed key(s), repeat this procedure from Step 1 for each additional key.


85


2011 Econoline (eco) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


FRONT SEATS


WARNING: Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal


injuries in the event of a collision.


WARNING: Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop.


WARNING: Before returning the seatback to its original position, make sure that cargo or any objects are not trapped


behind the seatback. After returning the seatback to its original position, pull on the seatback to ensure that it has fully latched. An unlatched seat may become dangerous in the event of a sudden stop or collision.


WARNING: Never adjust the driver’s seat or seatback when the vehicle is moving.


WARNING: Always drive and ride with your seatback upright and the lap belt snug and low across the hips.


Non-adjustable head restraints Your vehicle is equipped with front row outboard non-adjustable head restraints.


WARNING: To minimize the risk of neck injury in the event of a crash, the driver and passenger occupants should not sit in


and/or operate the vehicle, until the seatback is placed in its proper position. The driver should never adjust the seatback while the vehicle is in motion.


86


2011 Econoline (eco) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


The non-adjustable head restraints consist of a trimmed foam covering over the upper structure of the seatback.


Properly adjust the seatback to an upright driving/riding position, so that the head restraint is positioned as close as possible to the back of your head.


Adjusting the front manual seat (if equipped)


WARNING: Never adjust the driver’s seat or seatback when the vehicle is moving.


WARNING: Always drive and ride with your seatback upright and the lap belt snug and low across the hips.


Lift handle to move seat forward or backward.


87


2011 Econoline (eco) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


Pull lever up to adjust seatback.


WARNING: Before returning the seatback to its


original position, make sure that cargo or any objects are not trapped behind the seatback. After returning the seatback to its original position, pull on the seatback to ensure that it has fully latched. An unlatched seat may become dangerous in the event of a sudden stop or collision.


Using the manual lumbar support (if equipped) The lumbar support control is located on the inboard side of the driver’s seat. Turn the lumbar support control clockwise to increase firmness. Turn the lumbar support control counterclockwise to increase softness.


Adjusting the front power seat (if equipped) The control is located on the outboard side of the seat cushion. Press to raise or lower the front portion of the seat cushion.


88


2011 Econoline (eco) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


Press to raise or lower the rear portion of the seat cushion.


Press the control to move the seat forward, backward, up or down.


REAR SEATS


Rear captains chair adjust — passenger side only Pull the lever to adjust the seat forward or backward.


89


2011 Econoline (eco) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


Quick-release captains chair (7 passenger configuration- second row only) To remove the seat: 1. Disengage the lap/shoulder belt from the seat by inserting a key or small screwdriver into the slot in the detachable anchor and lifting upward.


2. Pull the seat latch handle, then pull the seat toward the right side of the vehicle to disengage four pins from the floor mount. 3. Remove the seat.


To install the seat:


WARNING: Check to see that the seat and seatback is latched securely in position. Keep floor area free of objects that would


prevent proper seat engagement. Never attempt to adjust the seat while the vehicle is in motion.


WARNING: Ensure that the seat is latched to the vehicle floor by pushing/pulling on the seat. If not latched, the seat may cause


injury during a sudden stop.


90


2011 Econoline (eco) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


1. Position the seat to the floor mount.


2. Pull the seat latch handle downward to lock the seat in position. 3. Make sure the safety belt is not twisted, then insert the safety belt tongue into the detachable anchor until you hear a “click” and feel the latch engage.


Rear bench seat To remove the seats: 1. Disengage the lap/shoulder belt from the seat by inserting a key or small screwdriver into the slot in the detachable anchor and lifting upward (2nd row passenger side only).


91


2011 Econoline (eco) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


2. Find the clips attached near the ends of the lap/shoulder belts.


3. Clip the end of the belt to the stationary portion of the shoulder belt coming out of the trim panel.


The end of the shoulder belt must be clipped in order to keep it from striking anything during vehicle operation.


92


2011 Econoline (eco) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


4. With assistance, pull the LH/RH seat latch release straps (1) (located behind the latch mechanisms) to release the latch from the rear strikers. 5. Lift the rear end of seat upward and rearward by pushing on the seatback (2) and lifting the seat cushion (3) to disengage the front seat hook and the rear seat latch from the striker. 6. With assistance, remove the seat assembly. • To remove the 3rd, 4th, and 5th row seats (if equipped), repeat


Steps 1 through 6. To install the seat:


WARNING: Ensure that the seat is installed or removed from the striker pins with adequate ergonomic assistance. Due to the


weight of the seat, it must be handled by at least two adults during installation or removal from the vehicle.


WARNING: Ensure that the seat is latched to the vehicle floor by pushing/pulling on the seat or seatback (2). If not latched,


the seat may cause injury during a sudden stop.


1. Please make sure the floor striker area is clean of any debris that would prevent the seat from latching. 2. With assistance, position the seat in the vehicle. 3. Align the front hooks to the LH/RH front striker pins prior to lowering the rear latch mechanism and aligning them with the rear striker pins.


93


2011 Econoline (eco) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


4. Engage the front LH/RH hooks to the LH/RH front striker pins. 5. After the front LH/RH hooks are engaged to the LH/RH front striker pins, pull LH/RH seat latch release straps to allow engagement of the latch to the striker pins. Refer to the illustration in To remove the rear seats above. 6. Pull/push seat back forward/backward to check for proper seat installation.


WARNING: Always latch the vehicle seat to the floor, whether the seat is occupied or empty. If not latched, the seat may cause


injury during a sudden stop.


WARNING: Do not hang or attach any cargo to the release straps of the rear bench seats. Doing so could cause the release straps to inadvertently unlatch the rear bench seat. If not latched, the seat may cause serious injury during a sudden stop.


SAFETY RESTRAINTS


Safety restraints precautions


WARNING: Always drive and ride with your seatback upright and the lap belt snug and low across the hips.


WARNING: To reduce the risk of injury, make sure children sit where they can be properly restrained.


WARNING: Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the


child from injury in a collision.


WARNING: All occupants of the vehicle, including the driver, should always properly wear their safety belts, even when an air


bag supplemental restraint system (SRS) is provided.


94


2011 Econoline (eco) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


WARNING: It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts. Be sure everyone in your vehicle is in a seat and using a safety belt properly.


WARNING: In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt.


WARNING: Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one


tongue that are designed to be used as a pair. 1) Use the shoulder belt on the outside shoulder only. Never wear the shoulder belt under the arm. 2) Never swing the safety belt around your neck over the inside shoulder. 3) Never use a single belt for more than one person.


WARNING: When possible, all children 12 years old and under should be properly restrained in a rear seating position.


WARNING: Safety belts and seats can become hot in a vehicle that has been closed up in sunny weather; they could burn a small child. Check seat covers and buckles before you place a child anywhere near them.


WARNING: Front and rear seat occupants, including pregnant women, should wear safety belts for optimum protection in an


accident.


Combination lap and shoulder belts 1. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle.


95


2011 Econoline (eco) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints • Front and rear seats


2. To unfasten, push the release button and remove the tongue from the buckle. • Front and rear seats


Restraint of pregnant women


WARNING: Always ride and drive with your seatback upright and the safety belt properly fastened. The lap portion of the


safety belt should fit snug and be positioned low across the hips. The shoulder portion of the safety belt should be positioned across the chest. Pregnant women should also follow this practice. See figure below.


96


2011 Econoline (eco) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


Pregnant women should always wear their safety belt. The lap belt portion of a combination lap and shoulder belt should be positioned low across the hips below the belly and worn as tight as comfort will allow. The shoulder belt should be positioned to cross the middle of the shoulder and the center of the chest.


Safety belt locking modes All safety restraints in the vehicle are combination lap and shoulder belts. The driver safety belt has the first locking mode and the passenger safety belts have both types of locking modes described as follows: Vehicle sensitive mode This is the normal retractor mode, which allows free shoulder belt length adjustment to your movements and locking in response to vehicle movement. For example, if the driver brakes suddenly or turns a corner sharply, or the vehicle receives an impact of approximately 5 mph (8 km/h) or more, the combination safety belts will lock to help reduce forward movement of the driver and passengers. In addition, the retractor is designed to lock if the webbing is pulled out too quickly. If this occurs, let the belt retract slightly and pull webbing out again in a slow and controlled manner. Automatic locking mode In this mode, the shoulder belt is automatically pre-locked. The belt will still retract to remove any slack in the shoulder belt. The automatic locking mode is not available on the driver safety belt. When to use the automatic locking mode This mode should be used any time a child safety seat, except a booster, is installed in passenger front or rear seating positions. Children 12 years old and under should be properly restrained in a rear seating position whenever possible. Refer to Safety restraints for children or Safety seats for children later in this chapter.


97


2011 Econoline (eco) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


How to use the automatic locking mode • Buckle the combination lap and


shoulder belt.


• Grasp the shoulder portion and pull downward until the entire belt is pulled out.


• Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode.


How to disengage the automatic locking mode Disconnect the combination lap/shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive (emergency) locking mode.


WARNING: After any vehicle collision, the safety belt system at all passenger seating positions must be checked by an authorized


dealer to verify that the “automatic locking retractor” feature for child seats is still functioning properly. In addition, all safety belts should be checked for proper function.


98


2011 Econoline (eco) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


WARNING: BELT AND RETRACTOR ASSEMBLY MUST BE REPLACED if the safety belt assembly “automatic locking


retractor” feature or any other safety belt function is not operating properly when checked by an authorized dealer. Failure to replace the belt and retractor assembly could increase the risk of injury in collisions.


Safety belt pretensioner Your vehicle is equipped with safety belt pretensioners at the driver and front outboard passenger seating positions. The safety belt pretensioner tightens the safety belts firmly against the occupant’s body at the start of the crash.


WARNING: The driver and front passenger safety belt system (including retractors, buckles and height adjusters) must be


replaced if the vehicle is involved in a collision that results in deployment of front airbags and safety belt pretensioners.


Front safety belt height adjustment The front seat and outboard positions are equipped with a height adjuster. Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder. To adjust the shoulder belt height, push the button and slide the height adjuster down. Release the button and pull down on the height adjuster to make sure it is locked in place. To adjust the belt upward, slide the adjuster up. Pull down on the height adjuster to make sure it is locked in place.


WARNING: Position the safety belt height adjusters so that the belt rests across the middle of your shoulder. Failure to adjust


the safety belt properly could reduce the effectiveness of the seat belt and increase the risk of injury in a collision.


99


2011 Econoline (eco) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


Then... The safety belt warning light illuminates and the warning chime sounds 4-8 seconds. The safety belt warning light and warning chime turn off.


Safety belt warning light and indicator chime The safety belt warning light illuminates in the instrument cluster and a chime sounds to remind the occupants to fasten their safety belts. Conditions of operation If... The driver’s safety belt is not buckled before the ignition switch is turned to the on position... The driver’s safety belt is buckled while the indicator light is illuminated and the warning chime is sounding... The driver’s safety belt is buckled before the ignition switch is turned to the on position... Belt-Minder姞 The Belt-Minder威 feature is a supplemental warning to the safety belt warning function. This feature provides additional reminders to the driver that the driver’s safety belt is unbuckled by intermittently sounding a chime and illuminating the safety belt warning lamp in the instrument cluster.


The safety belt warning light and the warning chime will remain off.


If... The driver’s safety belt is not buckled approximately 5 seconds after the safety belt warning light has turned off...


The driver’s safety belt is buckled while the safety belt indicator light is illuminated and the safety belt warning chime is sounding... The driver’s safety belt is buckled before the ignition switch is turned to the ON position... 100


Then... The Belt-Minder威 feature is activated - the safety belt warning light illuminates and the warning chime sounds for 6 seconds every 30 seconds, repeating for approximately 5 minutes or until safety belt is buckled. The Belt-Minder威 feature will not activate.


The Belt-Minder威 feature will not activate.


2011 Econoline (eco) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


The following are reasons most often given for not wearing safety belts: (All statistics based on U.S. data) Reasons given... “Crashes are rare events”


Consider... 36700 crashes occur every day. The more we drive, the more we are exposed to “rare” events, even for good drivers. 1 in 4 of us will be seriously injured in a crash during our lifetime. 3 of 4 fatal crashes occur within 25
miles of home. We design our safety belts to enhance comfort. If you are uncomfortable - try different positions for the safety belt upper anchorage and seatback which should be as upright as possible; this can improve comfort. Prime time for an accident. Belt-Minder威 reminds us to take a few seconds to buckle up. Safety belts, when used properly, reduce risk of death to front seat occupants by 45% in cars, and by 60% in light trucks. Nearly 1 of 2 deaths occur in single-vehicle crashes, many when no other vehicles are around. Possibly, but a serious crash can do much more than wrinkle your clothes, particularly if you are unbelted. Set the example, teen deaths occur 4
times more often in vehicles with TWO or MORE people. Children and younger brothers/sisters imitate behavior they see.


101


“I’m not going far”


“Belts are uncomfortable”


“I was in a hurry”


“Safety belts don’t work”


“Traffic is light”


“Belts wrinkle my clothes”


“The people I’m with don’t wear belts”


2011 Econoline (eco) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


Reasons given... “I have an airbag”


“I’d rather be thrown clear”


Consider... Airbags offer greater protection when used with safety belts. Frontal airbags are not designed to inflate in rear and side crashes or rollovers. People who are ejected are 40
times more likely to DIE. Safety belts help prevent ejection, WE CAN’T “PICK OUR CRASH”.


WARNING: Do not sit on top of a buckled safety belt or insert a latchplate into the buckle to avoid the Belt-Minder威 chime. To


do so may adversely affect the performance of the vehicle’s air bag system


One-time disable Any time the safety belt is buckled and then unbuckled during an ignition on cycle, the Belt-Minder威 will be disabled for that ignition cycle only. Deactivating/activating the Belt-Minder姞 feature Read Steps 1 - 5 thoroughly before proceeding with the deactivation/activation programming procedure. The Belt-Minder威 feature can be deactivated/activated by performing the following procedure: Before following the procedure, make sure that: • the parking brake is set • the gearshift is in P (Park) • the ignition switch is in the off position • all vehicle doors and the hood are closed • the driver’s safety belt is unbuckled • the parking lamps/headlamps are in the off position


WARNING: While the design allows you to deactivate your Belt-Minder威, this system is designed to improve your chances of


being safely belted and surviving an accident. We recommend you leave the Belt-Minder威 system activated for yourself and others who may use the vehicle. To reduce the risk of injury, do not deactivate/activate the Belt-Minder威 feature while driving the vehicle.


102


2011 Econoline (eco) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


1. Turn the ignition switch to the ON position. DO NOT START THE ENGINE. 2. Wait until the safety belt warning light turns off (Approximately one minute). • Step 3 must be completed within 30 seconds after the safety belt


warning light turns off.


3. Buckle then unbuckle the safety belt three times at a moderate speed, ending with the safety belt in the unbuckled state. • After Step 3 is complete, the safety belt warning light will be turned • Belt-Minder威 will automatically exit programming mode without


on for three seconds.


changing its enable status if Step 4 does not occur within 10 seconds of the end of Step 3.


4. Within approximately seven seconds of the light turning off, buckle then unbuckle the safety belt. • This will disable the Belt-Minder威 feature for that seating position if it is currently enabled. As confirmation, the safety belt warning light will flash four times per second for three seconds. • This will enable the Belt-Minder威 feature for that seating position if it is currently disabled. As confirmation, the safety belt warning light will flash four times per second for three seconds, followed by three seconds with the light off, then followed by the safety belt warning light flashing four times per second for three seconds again.


5. After receiving confirmation, the deactivation/activation procedure is complete.


Safety belt extension assembly If the safety belt is too short when fully extended, there is a 9 inch (23 cm) or 12 inch (31 cm) safety belt extension assembly that can be added (part number 611C22). This assembly can be obtained from an authorized dealer. Use only extensions manufactured by the same supplier as the safety belt. Manufacturer identification is located at the end of the webbing on the label. Also, use the safety belt extension only if the safety belt is too short for you when fully extended. Use the shortest extender assembly that will provide adequate fit.


103


2011 Econoline (eco) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


WARNING: Do not use extensions to change the fit of the shoulder belt across the torso.


AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS)


Important SRS precautions The SRS is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries. Airbags DO NOT inflate slowly; there is a risk of injury from a deploying airbag.


WARNING: All occupants of the vehicle, including the driver, should always properly wear their safety belts, even when an air


bag supplemental restraint system (SRS) is provided.


WARNING: Always transport children 12 years old and under in a rear seating position, and always properly use appropriate child


restraints. Never place a rear-facing child seat in front of an active airbag. If you must transport a forward-facing child in the front seat, move the seat all the way back and use appropriate restraints.


104


2011 Econoline (eco) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


WARNING: National Highway Traffic Safety Administration (NHTSA) recommends a minimum distance of at least 10 inches


(25 cm) between an occupant’s chest and the driver airbag module.


WARNING: Never place your arm over the air bag module as a deploying air bag can result in serious arm fractures or other


injuries.


pedals comfortably.


To properly position yourself away from the airbag: • Move your seat to the rear as far as you can while still reaching the • Recline the seat slightly one or two degrees from the upright position. WARNING: Do not put anything on or over the air bag module. Placing objects on or over the air bag inflation area may cause those objects to be propelled by the air bag into your face and torso causing serious injury.


WARNING: Do not attempt to service, repair, or modify the airbag supplemental restraint systems or its fuses. Contact your


authorized dealer as soon as possible.


WARNING: Modifying or adding equipment to the front end of the vehicle (including frame, bumper, front end body structure


and tow hooks) may affect the performance of the airbag system, increasing the risk of injury. Do not modify the front end of the vehicle.


WARNING: Additional equipment may affect the performance of the airbag sensors increasing the risk of injury.


105


2011 Econoline (eco) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


Children and airbags Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position. Failure to follow these instructions may increase the risk of injury in a collision.


WARNING: Airbags can kill or injure a child in a child seat. NEVER place a rear-facing child seat in front of an active airbag. If you must use a forward-facing child seat in the front seat, move the seat all the

Loading...
x