Download PDF Manual

Table of Contents


12


12
16
19


19
20
25
31


31
32
34


34
38
39
44


44
44
48
49
50
54


54
54
59


59
65
75
84


Introduction


Instrument Cluster


Warning lights and chimes Gauges


Entertainment Systems


AM/FM stereo AM/FM stereo with single CD AM/FM stereo with in-dash six CD


Climate Controls


Heater only Manual heating and air conditioning


Lights


Headlamps Turn signal control Bulb replacement Driver Controls


Windshield wiper/washer control Steering wheel adjustment Power windows Mirrors Speed control


Locks and Security


Keys Locks


Seating and Safety Restraints


Seating Safety restraints Airbags Child restraints


2006 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)


101


103
105
120
127
138
139


139
142
144
150
160


160
162
162
164
171
180
181
186
187


193
194


198


Table of Contents


Tires, Wheels and Loading


Tire Information Tire Inflation Vehicle loading Trailer towing Recreational towing


Driving


Starting Brakes Traction control/AdvanceTrac Transmission operation


Roadside Emergencies


Getting roadside assistance Hazard flasher switch Fuel pump shut-off switch Fuses and relays Changing tires Lug Nut Torque Jump starting Wrecker towing


Customer Assistance


Reporting safety defects (U.S. only)


Cleaning


Underbody preservation


2006 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)


Maintenance and Specifications


Engine compartment Engine oil Battery Engine Coolant Fuel information Air filter(s) Part numbers Refill capacities Lubricant specifications Engine data Accessories


Index


Table of Contents


200


201
203
207
209
215
229
231
232
236
239
244


246


All rights reserved. Reproduction by any means, electronic or mechanical including photocopying, recording or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from Ford Motor Company. Ford may change the contents without notice and without incurring obligation.


Copyright © 2006 Ford Motor Company


2006 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)


Introduction


CALIFORNIA Proposition 65 Warning


WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to


the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.


CONGRATULATIONS Congratulations on acquiring your new Ford. Please take the time to get well acquainted with your vehicle by reading this handbook. The more you know and understand about your vehicle, the greater the safety and pleasure you will derive from driving it. For more information on Ford Motor Company and its products visit the following website: • In the United States: www.ford.com • In Canada: www.ford.ca • In Australia: www.ford.com.au • In Mexico: www.ford.com.mx Additional owner information is given in separate publications. This Owner’s Guide describes every option and model variant available and therefore some of the items covered may not apply to your particular vehicle. Furthermore, due to printing cycles it may describe options before they are generally available. Remember to pass on this Owner’s Guide when reselling the vehicle. It is an integral part of the vehicle.


Fuel pump shut-off switch: In the event of an accident the safety switch will automatically cut off the fuel supply to the


engine. The switch can also be activated through sudden vibration (e.g. collision when parking). To reset the switch, refer to the Fuel pump shut-off switch in the Roadside Emergencies chapter.


SAFETY AND ENVIRONMENT PROTECTION


Warning symbols in this guide


How can you reduce the risk of personal injury to yourself or others? In this guide, answers to such questions are contained in comments highlighted by the warning triangle symbol. These comments should be read and observed.


2006 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)


Introduction


Warning symbols on your vehicle


When you see this symbol, it is imperative that you consult the relevant section of this guide before touching or attempting adjustment of any kind.


Protecting the environment We must all play our part in protecting the environment. Correct vehicle usage and the authorized disposal of waste, cleaning and lubrication materials are significant steps towards this aim. Information in this respect is highlighted in this guide with the tree symbol.


BREAKING-IN YOUR VEHICLE During the first 1,000 miles (1,600 km) of driving, maintain speeds below 70 mph (110 km/h) and vary speeds frequently. This is recommended to give the moving parts a chance to break in. Do not tow a trailer during this break-in period. For more detailed information about towing a trailer, refer to Trailer towing in the Tires, Wheels and Loading chapter.


SPECIAL NOTICES


New Vehicle Limited Warranty For a detailed description of what is covered and what is not covered by your vehicle’s New Vehicle Limited Warranty, refer to the Warranty Guide that is provided to you along with your Owner’s Guide.


Service Data Recording Service data recorders in your vehicle are capable of collecting and storing diagnostic information about your vehicle. This potentially includes information about the performance or status of various systems and modules in the vehicle, such as engine, throttle, steering or brake systems. In order to properly diagnose and service your vehicle, Ford Motor Company, Ford of Canada, and service and repair facilities may access vehicle diagnostic information through a direct connection to your vehicle when diagnosing or servicing your vehicle.


2006 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)


Introduction


brake pedal;


Event Data Recording Other modules in your vehicle — event data recorders — are capable of collecting and storing data during a crash or near crash event. The recorded information may assist in the investigation of such an event. The modules may record information about both the vehicle and the occupants, potentially including information such as: • how various systems in your vehicle were operating; • whether or not the driver and passenger seatbelts were buckled; • how far (if at all) the driver was depressing the accelerator and/or the • how fast the vehicle was traveling; and • where the driver was positioning the steering wheel. To access this information, special equipment must be directly connected to the recording modules. Ford Motor Company and Ford of Canada do not access event data recorder information without obtaining consent, unless pursuant to court order or where required by law enforcement, other government authorities or other third parties acting with lawful authority. Other parties may seek to access the information independently of Ford Motor Company and Ford of Canada. Vehicle Modification Data Recording Some aftermarket products may cause severe engine and/or transmission damage; refer to the What is not covered section in The new vehicle limited warranty for your vehicle chapter of your vehicle’s Warranty Guide for more information. Some vehicles are equipped with Powertrain Control Systems that can detect and store information about vehicle modifications that increase horsepower and torque output; this information cannot be erased and will stay in the system’s memory even if the modification is removed. When a dealer or repair facility works on your vehicle, it may be necessary for them to access the information in the Powertrain Control System. This information will likely identify if any unauthorized modifications have been made to the system and may be used to determine if repairs will be covered by warranty.


2006 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)


Introduction


Special instructions For your added safety, your vehicle is fitted with sophisticated electronic controls.


Please read the section Supplemental restraint system (SRS) in the Seating and Safety Restraints chapter. Failure to follow the specific warnings and instructions could result in personal injury.


Front seat mounted rear-facing child or infant seats should NEVER be placed in front of an active passenger airbag.


Notice to owners of diesel-powered vehicles Read the 6.0 Liter Power Stroke Direct Injection Turbo Diesel Owner’s Guide Supplement for information regarding correct operation and maintenance of your Diesel-powered light truck.


Notice to owners of pickup trucks and utility type vehicles


Utility vehicles have a significantly higher rollover rate than other types of vehicles.


Before you drive your vehicle, please read this Owner’s Guide carefully. Your vehicle is not a passenger car. As with other vehicles of this type, failure to operate this vehicle correctly may result in loss of vehicle control, vehicle rollover, personal injury or death.


2006 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)


Introduction


Using your vehicle as an ambulance If your light truck is equipped with the Ford Ambulance Preparation Package, it may be utilized as an ambulance. Ford urges ambulance manufacturers to follow the recommendations of the Ford Incomplete Vehicle Manual, Ford Truck Body Builder’s Layout Book and the Qualified Vehicle Modifiers (QVM) Guidelines as well as pertinent supplements. For additional information, please contact the Truck Body Builders Advisory Service at 1–877–840–4338. Use of your Ford light truck as an ambulance, without the Ford Ambulance Preparation Package voids the Ford New Vehicle Limited Warranty and may void the Emissions Warranties. In addition, ambulance usage without the preparation package could cause high underbody temperatures, overpressurized fuel and a risk of spraying fuel which could lead to fires. If your vehicle is equipped with the Ford Ambulance Preparation Package, it will be indicated on the Safety Compliance Certification Label. The label is located on the driver’s side door pillar or on the rear edge of the driver’s door. You can determine whether the ambulance manufacturer followed Ford’s recommendations by directly contacting that manufacturer. Ford Ambulance Preparation Package is only available on certain 6.0L Diesel engine equipped vehicles.


2006 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)


Introduction


Using your vehicle as a stationary power source (PTO) Refer to the Driving chapter for more information and guidelines for operating a vehicle equipped with an aftermarket power take-off system.


Cell phone use The use of Mobile Communications Equipment has become increasingly important in the conduct of business and personal affairs. However, drivers must not compromise their own or others’ safety when using such equipment. Mobile Communications can enhance personal safety and security when appropriately used, particularly in emergency situations. Safety must be paramount when using mobile communications equipment to avoid negating these benefits. Mobile Communication Equipment includes, but is not limited to cellular phones, pagers, portable email devices, in-vehicle communications systems, telematics devices and portable two-way radios.


A driver’s first responsibility is the safe operation of the vehicle. The most important thing you can do to prevent a crash is to


avoid distractions and pay attention to the road. Wait until it is safe to operate Mobile Communications Equipment.


Middle East/North Africa vehicle specific information For your particular global region, your vehicle may be equipped with features and options that are different from the ones that are described in this Owner’s Guide; therefore, a supplement has been supplied that complements this book. By referring to the pages in the provided supplement, you can properly identify those features, recommendations and specifications that are unique to your vehicle. Refer to this Owner’s Guide for all other required information and warnings.


2006 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)


Introduction


These are some of the symbols you may see on your vehicle.


Vehicle Symbol Glossary


Safety Alert


See Owner’s Guide


Fasten Safety Belt


Airbag - Front


Airbag - Side


Child Seat


Child Seat Installation Warning


Child Seat Tether Anchor


Anti-Lock Brake System


Child Seat Lower Anchor


Brake System


Brake Fluid - Non-Petroleum Based


Powertrain Malfunction


Speed Control


Master Lighting Switch


Hazard Warning Flasher


Fog Lamps-Front


Fuse Compartment


Fuel Pump Reset


Windshield Wash/Wipe


Windshield Defrost/Demist


Rear Window Defrost/Demist


10


2006 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)


Introduction


Vehicle Symbol Glossary


Power Windows Front/Rear


Child Safety Door Lock/Unlock


Power Window Lockout


Interior Luggage Compartment Release Symbol


Panic Alarm


Engine Oil


Engine Coolant


Engine Coolant Temperature


Do Not Open When Hot


Battery


Avoid Smoking, Flames, or Sparks


Battery Acid


Explosive Gas


Fan Warning


Power Steering Fluid


Maintain Correct Fluid Level


MAX MIN


Emission System


Engine Air Filter


Passenger Compartment Air Filter


Jack


Check Fuel Cap


Low Tire Pressure Warning


11


2006 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)


Instrument Cluster


WARNING LIGHTS AND CHIMES


Warning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’s functions. Many lights will illuminate when you start your vehicle to make sure the bulb works. If any light remains on after starting the vehicle, refer to the respective system warning light for additional information. If your vehicle is equipped with a Diesel engine, it has a unique cluster, refer to Starting the engine in your 6.0 Liter Power Stroke Direct Injection Turbo Diesel Owner’s Guide Supplement. Service engine soon: The Service engine soon indicator light illuminates when the ignition is first turned to the ON position to check the bulb. Solid illumination after the engine is started indicates the On Board Diagnostics System (OBD-II) has detected a malfunction. Refer to On board diagnostics (OBD-II) in the Maintenance and Specifications chapter. If the light is blinking, engine misfire is occurring which could damage your catalytic converter. Drive in a moderate fashion (avoid heavy acceleration and deceleration) and have your vehicle serviced immediately by your authorized dealer.


Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter, the fuel system, interior floor coverings or other vehicle components, possibly causing a fire.


12


2006 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)


Instrument Cluster


Electronic throttle control (if equipped): Illuminates when the engine has defaulted to a ’limp-home’ operation. Report the fault to a dealer at the earliest opportunity. Check fuel cap: Illuminates when the fuel cap may not be properly installed. Continued driving with this light on may cause the Service Engine Soon warning light to come on, refer to Fuel filler cap in the Maintenance and Specification chapter. Brake system warning light: To confirm the brake system warning light is functional, it will momentarily illuminate when the ignition is turned to the ON position when the engine is not running, or in a position between ON and START, or by applying the parking brake when the ignition is turned to the ON position. If the brake system warning light does not illuminate at this time, seek service immediately from your authorized dealer. Illumination after releasing the parking brake indicates low brake fluid level and the brake system should be inspected immediately by your authorized dealer.


BRAKE


Driving a vehicle with the brake system warning light on is dangerous. A significant decrease in braking performance may


occur. It will take you longer to stop the vehicle. Have the vehicle checked by your authorized dealer.


Anti-lock brake system: If the ABS light stays illuminated or continues to flash, a malfunction has been detected, have the system serviced immediately by your authorized dealer. Normal braking is still functional unless the brake warning light also is illuminated.


ABS


13


2006 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)


Instrument Cluster


Airbag readiness: If this light fails to illuminate when ignition is turned to ON, continues to flash or remains on, have the system serviced immediately by your authorized dealer. A chime will also sound when a malfunction in the supplemental restraint system has been detected. Safety belt: Reminds you to fasten your safety belt. A chime will also sound to remind you to fasten your safety belt.


AdvanceTrac威 (if equipped): Flashes (two times per second) when the AdvanceTrac威 with RSC system is active. If the light remains on, or ⬙SERVICE RSC NOW⬙ is displayed in the odometer display with a chime, have the system serviced immediately by your authorized dealer. (Flashes one time every two seconds when AdvanceTrac威 with RSC system has not yet initialized and is not available.) For further information, refer to AdvanceTrac威 with RSC stability enhancement system in the Driving chapter.


If your vehicle is equipped with the AdvanceTrac威 with RSC system, then it was designed to be operated with RSC. Driving


without a functioning RSC娂 system could be dangerous. Reduce speed and proceed to an authorized dealer to have the system serviced immediately.


Charging system: Illuminates when the battery is not charging properly.


Low fuel: Illuminates when the fuel level in the fuel tank is at or near empty (refer to Fuel gauge in this chapter).


14


2006 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)


Instrument Cluster


is high.


CHECK GAGE


Check gauge: Illuminates when any of the following conditions has occurred: • The engine coolant temperature • The engine oil pressure is low. • Flashes when Failsafe cooling mode has been activated. Turn signal: Illuminates when the left or right turn signal or the hazard lights are turned on. If the indicators stay on or flash faster, check for a burned out bulb. High beams: Illuminates when the high beam headlamps are turned on.


OVERDRIVE


Transmission control indicator light (TCIL): Illuminates when the overdrive function of the transmission has been turned off, refer to the Driving chapter. If the light flashes steadily or does not illuminate, have the transmission serviced soon, or damage may occur. Transmission Tow/Haul light (TCIL) (5.4L and 6.8L gasoline engines only): Illuminates when the Tow/Haul feature of the transmission has been turned on, refer to the Driving chapter. Key-in-ignition warning chime: Sounds when the key is left in the ignition in the OFF/LOCK or ACCESSORY position and the driver’s door is opened. Headlamps on warning chime: Sounds when the headlamps or parking lamps are on, the ignition is off (the key is not in the ignition) and the driver’s door is opened. Parking brake ON warning chime: Sounds when the parking brake is set, the engine is running and the vehicle is driven more than 3 mph (5
km/h).


15


2006 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)


Instrument Cluster


GAUGES


Speedometer: Indicates the current vehicle speed.


Engine coolant temperature gauge: Indicates engine coolant temperature. At normal operating temperature, the needle will be in the normal range (between “H” and “C”). If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely possible, switch off the engine and let the engine cool.


Never remove the coolant reservoir cap while the engine is running or hot.


16


2006 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)


Odometer: Registers the total miles (kilometers) of the vehicle.


Instrument Cluster


Trip odometer: Registers the miles (kilometers) of individual journeys. Press the SELECT/RESET control once to switch from the odometer to the trip odometer. Press the control again to select Trip A and Trip B features. To reset the trip, press and hold the control again until the trip reading is 0.0 miles. Tachometer: Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer continuously at the top of the scale may damage the engine.


Battery voltage gauge: Indicates the battery voltage when the ignition is in the ON position. If the pointer moves and stays outside the normal operating range, have the vehicle’s electrical system checked by your authorized dealer as soon as possible. Engine oil pressure gauge: Indicates engine oil pressure. The needle should stay in the normal operating range (between “L” and “H”). If the needle falls below the normal range, stop the vehicle, turn off the engine and check the engine oil level. Add oil if needed. If the oil level is correct, have your vehicle checked by your authorized dealer.


17


2006 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)


Instrument Cluster


Fuel gauge: Indicates approximately how much fuel is left in the fuel tank (when the ignition is in the ON position). The fuel gauge may vary slightly when the vehicle is in motion or on a grade. The FUEL icon and arrow indicates which side of the vehicle the fuel filler door is located. Refer to Filling the tank in the Maintenance and Specifications chapter for more information.


18


2006 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)


Entertainment Systems


AUDIO SYSTEMS


AM/FM stereo (if equipped)


1. Seek: Press to find the next listenable station down/up the frequency band. 2. Tune: Press to manually adjust the radio frequency down/up.


3. AM/FM: Press to choose a frequency band in radio mode.


4. Memory preset buttons: To set a station: Select frequency band AM/FM1/FM2; tune to a station, press and hold a preset button until sound returns.


AM/FM


19


2006 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)


Entertainment Systems


5. Power/volume: Press to turn ON/OFF; turn to increase or decrease volume levels.


VOL PUSH ON


6. Tone: Press TONE until the desired level — Bass, Treble, Fade appears on the display. Turn the volume control to raise/lower the levels, or to move the audio sound from the right to left or the front to back (if equipped). 7. CLK (Clock): To set the hour, press and hold CLK until CLOCK SET appears in the display. Press SEEK to decrease increase To set the minute, press and hold CLK until CLOCK SET appears in the display. Press TUNE to decrease


the minutes.


or increase


the hours.


or


TONE


CLK


Satellite Compatible AM/FM Stereo In-Dash Single CD/MP3 Radio (if equipped)


20


2006 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)


Entertainment Systems


for previous/next


1. SEEK: Press and release SEEK strong station or track. 2. TEXT: The filename (Fi), song title (So), artist text (Ar) or album text (AL) may be viewed while playing an MP3 selection. When MP3 selection text is shown on the message display, its corresponding text indicator (Fi, So, Ar, or AL) is shown in the elapsed time display. Press TEXT to scroll through the text fields. The display will scroll through all of the text in the current field before changing to the next field. (TEXT must be pressed within 3
seconds of the previous press to proceed to the next/last text display. The last text field shown on the display will become the new display message default. TEXT is also available when equipped with Satellite radio. Your radio comes equipped with Satellite ready capability. The kit to enable Satellite reception is available through your dealer. Detailed Satellite instructions are included with the dealer installed kit. Dealer installed satellite kit only available in the continental United States. 3. AUX: This function is not operational.


4. MUTE: Press to MUTE playing media; press again to return to playing media. 5. EJ: Press to eject a CD.


to decrease/increase


6. Bass: Press BASS; then press SEL the bass output. Treble: Press TREB; then press SEL the treble output.


to decrease/increase


21


2006 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)


Entertainment Systems


7. Select: Use with Bass, Treble, Balance, Fade and other menu selections.


8. Balance: Press BAL; then press to shift sound to the SEL left/right speakers. Fade: Press FADE; then press SEL rear/front speakers. 9. Menu: Press MENU and SEL to access/adjust the following functions:


to shift sound to the


) or decrease ) the hours/minutes. Press MENU again to disengage clock mode.


Autoset: Press MENU until AUTOSET appears in the display. Press SEL to toggle ON/OFF. Allows you to set the strongest local radio stations without losing your original manually set preset stations for AM/FM1/FM2. When the six strongest stations are filled, the station stored in preset 1 will begin playing. If there are less than six strong stations, the system will store the last one in the remaining presets. Setting the clock: Press MENU until SELECT HOUR or SELECT MINUTE is displayed. Use SEL to manually increase ( Folder/Track mode: In MP3 mode, press MENU until MODE appears in the display. Use SEL to toggle between FOLDER (only tracks within selected folder are accessible) or TRACK (all tracks on disc are accessible) MODE. 10. REPEAT: Repeats the current CD/MP3 track when active (ON). Press to show repeat status. Press again to toggle status. 11. SHUFFLE: Plays CD/MP3
tracks in random order when active (ON). Press to show shuffle status. Press again to toggle status. 12. FOLDER the next MP3 directory.


: Press to access


22


2006 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)


Entertainment Systems


13. FOLDER the previous MP3 directory.


: Press to access


14. FF(Fast forward): In CD/MP3
mode, press until desired selection is reached. 15. REW(Rewind): In CD/MP3
mode, press until desired selection is reached. 16. SAT (if equipped): Your radio comes equipped with Satellite Ready capability. The kit to enable the Satellite reception is available through your dealer. Detailed satellite instructions are included with the dealer installed kit. Dealer installed satellite kit only available in the continental United States. 17. BAND: Press to toggle between AM/FM1/FM2 frequency band.


18. Memory presets: To set a station: Select frequency band; tune to a station, press and hold a preset button until sound returns. 19. Power/volume: Press to turn ON/OFF; turn to increase or decrease volume levels.


20. CD: Press to enter CD mode.


23


2006 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)


Entertainment Systems


CD units are designed to play commercially pressed 4.75 in (12
cm) audio compact discs only. Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players. Irregular shaped CDs, CDs with a scratch protection film attached, and CDs with homemade paper (adhesive) labels should not be inserted into the CD player. The label may peel and cause the CD to become jammed. It is recommended that homemade CDs be identified with permanent felt tip marker rather than adhesive labels. Ballpoint pens may damage CDs. Please contact your authorized dealer for further information. 21. COMP(Compression): Brings soft and loud CD passages together for a more consistent listening level when in CD mode. Press COMP to turn the feature ON/OFF. 22. Scan: Press SCAN to hear a brief sampling of radio stations or CD/MP3 tracks. Press again to stop. 23. CAT/Tune: Press to


or


manually tune down/up the radio frequency band. CAT: CAT is only available when equipped with Satellite Radio. Your radio comes equipped with Satellite ready capability. The kit to enable Satellite reception is available through your dealer. Detailed Satellite instructions are included with the dealer installed kit. Dealer installed satellite kit only available in the continental United States. For information regarding SIRIUS Satellite Radio, please call toll-free 888-539-SIRIUS (888-539-7474) or visit the SIRIUS website at www.siriusradio.com 24. CD slot: Insert a CD with the label side up.


24


2006 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)


Entertainment Systems


Premium Satellite Compatible AM/FM Stereo In-Dash Six CD/MP3
Radio (if equipped)


for previous/next


1. SEEK: Press and release SEEK strong station or track. 2. TEXT: The filename (Fi), song title (So), artist text (Ar) or album text (AL) may be viewed while playing an MP3 selection. When MP3 selection text is shown on the message display, its corresponding text indicator (Fi, So, Ar, or AL) is shown in the elapsed time display. Press TEXT to scroll through the text fields. The display will scroll all of the text in the current field before changing to the next field. (TEXT must be pressed within 3 seconds of the previous button press to proceed to the next/last text display.) TEXT is also available when equipped with Satellite radio. Your radio comes equipped with Satellite ready capability. The kit to enable Satellite reception is available through your dealer. Detailed Satellite instructions are included with the dealer installed kit. Dealer installed satellite kit only available in the continental United States.


25


2006 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)


Entertainment Systems


3. AUX: Press to toggle between the current playing media and DVD (if equipped). 4. MUTE: Press to MUTE playing media; press again to return to playing media 5. EJ: Press to eject a CD. Press EJ and a memory preset to eject a specific disc. Press and hold to eject all loaded discs. 6. Bass: Press BASS; then press SEL the bass output. Treble: Press TREB; then press SEL the treble output.


to decrease/increase


to decrease/increase


7. Select: Use with Bass, Treble, Balance, Fade and other menu functions.


to shift sound to the


8. Balance: Press BAL; then press to shift sound to the SEL left/right speakers. Fade: Press FADE; then press SEL rear/front speakers. 9. Menu: Press to access the following functions: Compression: Brings soft and loud CD passages together for a more consistent listening level when in CD mode. Press MENU until compression status is displayed. Press the SEL control to enable the compression feature when COMPRESS OFF is displayed. Press the SEL control again to disable the feature when COMPRESS ON is displayed. Autoset: Press MENU until AUTOSET appears in the display. Press SEL to toggle ON/OFF. Allows you to set the strongest local radio stations without losing your original manually set preset stations for


26


2006 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)


Entertainment Systems


) or decrease ) the hours/minutes. Press MENU again to disengage clock mode.


AM/FM1/FM2. When the six strongest stations are filled, the station stored in preset 1 will begin playing. If there are less than six strong stations, the system will store the last one in the remaining presets. Setting the clock: Press MENU until SELECT HOUR or SELECT MINUTE is displayed. Use SEL to manually increase ( Folder/Track Mode: In MP3 mode, press MENU until MODE appears in the display. Use SEL to toggle between FOLDER (only tracks within selected folder are accessible) or TRACK (all tracks on disc are accessible) MODE. 10. REPEAT: Press to repeat the current CD/MP3 track. Press again to disable. 11. SHUFFLE: Press play the CD/MP3 tracks on the current disc in random order. Press again to disable. 12. FOLDER the next MP3 directory.


: Press to access


13. FOLDER the previous MP3 directory


: Press to access


14. FF(Fast forward): In CD/MP3
mode, press until desired selection is reached. 15. REW(Rewind): In CD/MP3
mode, press until desired selection is reached. 16. SAT (if equipped): Your radio comes equipped with Satellite Ready capability. The kit to enable the Satellite reception is available through your dealer. Detailed satellite instructions are included with the dealer installed kit. Dealer installed satellite kit only available in the continental United States. 17. BAND: Press to toggle between AM/FM1/FM2 frequency band.


27


2006 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)


Entertainment Systems


18. Memory presets: To set a station: Select frequency, tune to a station, press and hold a preset button until sound returns. 19. Power/volume: Press to turn ON/OFF; turn to increase or decrease volume levels.


20. Load: Press to load a CD. Press LOAD and a memory preset to load to a specific disc slot. Press and hold to load up to six discs. 21. CD: Press to enter CD mode.


CD units are designed to play commercially pressed 4.75 in (12
cm) audio compact discs only. Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players. Irregular shaped CDs, CDs with a scratch protection film attached, and CDs with homemade paper (adhesive) labels should not be inserted into the CD player. The label may peel and cause the CD to become jammed. It is recommended that homemade CDs be identified with permanent felt tip marker rather than adhesive labels. Ballpoint pens may damage CDs. Please contact your authorized dealer for further information. 22. Scan: Press SCAN to hear a brief sampling of radio stations or CD/MP3 tracks. Press again to stop. 23. Disc/Tune: Press to


or


manually tune down/up the radio frequency band, or to listen to the previous/next CD. CAT: CAT is only available when equipped with Satellite Radio. Your Audiophile radio comes equipped with Satellite ready capability. The kit to enable Satellite reception is available through your dealer. Detailed Satellite instructions are included with the dealer installed kit. Dealer installed satellite kit only available in the continental United States.


28


2006 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)


Entertainment Systems


For information regarding SIRIUS Satellite Radio, please call toll-free 888-539-SIRIUS (888-539-7474) or visit the SIRIUS website at www.siriusradio.com 24. CD slot: Insert a CD, label side up.


Accessory delay With accessory delay, the window switches, moon roof (if equipped) and audio system may be used for up to ten minutes after the ignition switch is turned off or until any door is opened.


GENERAL AUDIO INFORMATION Radio frequencies: AM and FM frequencies are established by the Federal Communications Commission (FCC) and the Canadian Radio and Telecommunications Commission (CRTC). Those frequencies are: AM: 530, 540–1700, 1710 kHz FM: 87.7, 87.9–107.7, 107.9 MHz Radio reception factors: There are three factors that can affect radio reception: • Distance/strength: The further you travel from an FM station, the • Terrain: Hills, mountains, tall buildings, power lines, electric fences, traffic lights and thunderstorms can interfere with your reception. • Station overload: When you pass a broadcast tower, a stronger signal may overtake a weaker one and play while the weak station frequency is displayed.


weaker the signal and the weaker the reception.


CD/CD player care Do: • Handle discs by their edges only. Never touch the playing surface. • Inspect discs before playing. Clean only with an approved CD cleaner


and wipe from the center out.


Don’t: • Expose discs to direct sunlight or heat sources for extended periods • Clean using a circular motion.


of time.


29


2006 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)


Entertainment Systems


CD units are designed to play commercially pressed 4.75 in (12
cm) audio compact discs only. Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players. Dirty, warped or damaged CDs, irregular shaped CDs, CDs with a scratch protection film attached, and CDs with homemade paper (adhesive) labels should not be inserted into the CD player. The label may peel and cause the CD to become jammed. It is recommended that homemade CDs be identified with permanent felt tip marker rather than adhesive labels. Ballpoint pens may damage CDs. Please contact your authorized dealer for further information. Audio system warranty and service Refer to the Warranty Guide for audio system warranty information. If service is necessary, see your dealer or qualified technician.


30


2006 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)


Climate Controls


HEATER ONLY SYSTEM (IF EQUIPPED) 1. Fan speed adjustment: Controls the volume of air circulated in the vehicle. 2. Temperature selection: Controls the temperature of the airflow in the vehicle. 3. Air flow selections: Controls the direction of the airflow in the vehicle. See the following for a brief description on each control. VENT: Distributes outside air through the instrument panel vents. FLR: Distributes outside air through the floor vents. OFF: Outside air is shut out and the climate system is turned off. MIX: Distributes outside air through the windshield defroster vents and the floor vents.


: Distributes outside air through the windshield defroster vents.


the air flow selector in the


Operating tips • To reduce fog build up on the windshield during humid weather, place • To reduce humidity build up inside the vehicle during cold or warm weather, do not drive with the air flow selector in the OFF position. • Do not put objects under the front seats that will interfere with the air • Remove any snow, ice or leaves from the air intake area at the base of


flow to the back seats.


position.


the windshield.


To aid in side window defogging/demisting in cold weather: 1. Select MIX. 2. Set the temperature control to maintain comfort. 3. Set the fan speed to HI.


Do not place objects on top of the instrument panel as these objects may become projectiles in a collision or sudden stop.


31


2006 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)


Climate Controls


MANUAL HEATING AND AIR CONDITIONING SYSTEM (IF EQUIPPED) 1. Fan speed adjustment: Controls the volume of air circulated in the vehicle. 2. Temperature selection: Controls the temperature of the airflow in the vehicle. 3. Air flow selections: Controls the direction of the airflow in the vehicle. See the following for a brief description on each control. MAX A/C: Uses recirculated air to cool the vehicle. Air flows from the instrument panel vents only. NORM A/C: Uses outside air to cool the vehicle. Air flows from the instrument panel vents only. VENT: Distributes outside air through the instrument panel vents. OFF: Outside air is shut out and the climate system is turned off. FLR: Distributes outside air through the floor vents. MIX: Distributes outside air through the windshield defroster vents and floor vents.


: Distributes outside air through the windshield defroster vents.


the air flow selector in the


Operating tips • To reduce fog build up on the windshield during humid weather, place • To reduce humidity build up inside the vehicle: do not drive with the • Do not put objects under the front seats that will interfere with the • Remove any snow, ice or leaves from the air intake area at the base of


air flow selector in the OFF position.


airflow to the back seats.


position.


the windshield.


32


2006 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)


Climate Controls


To aid in side window defogging/demisting in cold weather: 1. Select MIX. 2. Set the temperature control to maintain comfort. 3. Set the fan speed to HI.


Do not place objects on top of the instrument panel as these objects may become projectiles in a collision or sudden stop.


REAR FAN SPEED ADJUSTMENT (IF EQUIPPED) The rear fan controls adjust the volume of air circulated in the rear of the vehicle.


33


2006 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)


Lights


HEADLAMP CONTROL • The first position turns on the parking, tail, license plate and side marker lamps. • The outer position turns on the


headlamps.


Battery saver The battery saver can be set to turn off the courtesy lamps within 2 or 10 minutes if a door is left open and the key is not in the ignition. Demand (manually switched on) interior lamps can be set to turn off within 2 or 30 minutes after the key has been removed from the ignition. Note: The vehicle is factory set at 2 minutes to turn off demand and courtesy lamps. The vehicle will change to 10 minutes for courtesy lamps and 30 minutes for demand interior lamps once the odometer reads over 50 miles. To change the battery saver duration time, do the following: 1. Turn the key to the RUN position. Do not start the vehicle. 2. After the odometer is displayed, press and release the reset button 10
times within 60 seconds. 3. The words ’Battery Saver’ will be displayed. 4. Press the reset button to select/toggle between ’2 minutes’ or ’30
minutes’ duration. 5. Once your time choice is displayed, wait until the odometer is displayed (approximately 30 seconds). The battery saver feature will now work with the new time duration. Note: Even when choosing the 30 minute time duration, the courtesy lamps can only have a maximum on time of 10 minutes. Only demand interior lamps will stay on for the entire 30 minute period.


34


2006 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)


Lights


Daytime running lamps (DRL) (if equipped) Turns the headlamps on with a reduced output. To activate: • the ignition must be in the ON position, • the headlamp control is in the OFF or parking lamp position and • the parking brake must be disengaged.


Always remember to turn on your headlamps at dusk or during inclement weather. The Daytime Running Lamp (DRL) system


does not activate the tail lamps and generally may not provide adequate lighting during these conditions. Failure to activate your headlamps under these conditions may result in a collision.


High beams Push the lever toward the instrument panel to activate. Pull the lever towards you to deactivate.


Flash to pass Pull toward you slightly to activate and release to deactivate.


2006 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)


35


Lights


PANEL DIMMER CONTROL To adjust the brightness of the instrument panel, rotate the dimmer control clockwise/counterclockwise when the headlamp control is in the parking lamp or low-beam position. To turn on the interior lamps, rotate the dimmer control fully counterclockwise. The dome lamp will not illuminate if the control switch is in the OFF position.


ground


HEADLAMP AIM ADJUSTMENT The headlamps are designed to be mechanically aimed, but can also be aimed visually by doing the following: 1. Park your vehicle on a level surface about 25 feet (7.6 meters) away from a vertical plain surface (3). Check your headlamp alignment at night or in a dark area so that you can see the headlamp beam pattern. • (1) 8 feet (2.4 meters) • (2) Center height of lamp to • (3) 25 feet (7.6 meters) • (4) Horizontal reference line • (5) Center of headlamps • (6) Center line of the vehicle 2. The center of the headlamp is marked either on the lens (a circle or cross marker) or on the bulb shield, internal to the lamp (mark or feature). Measure the height from the center of your headlamp to the ground (2) and mark an 8 foot (2.4 meter) long horizontal line on the wall or screen (1) at this height (masking tape works well).


36


2006 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)


Lights


3. Turn on the low beam headlamps and open the hood. 4. Locate the high intensity area of the beam pattern and place the top edge of the intensity zone even with the horizontal reference line (4). If the top edge of the high intensity area is not even with the horizontal line, follow the next step to adjust it. 5. • Aerodynamic: Locate the


vertical adjuster (2) for each headlamp. Adjust the aim by turning the adjuster control either clockwise (to adjust up) or counterclockwise (to adjust down).


• Sealed beam: Locate the vertical adjuster (1) for each headlamp. Adjust the aim by turning the adjuster control either clockwise (to adjust up) or counterclockwise (to adjust down).


6. In addition to the horizontal line marked in step 2, a pair of vertical lines (5) must be marked at the center line of the headlamps on the wall or screen. 7. On the wall or screen, locate the high intensity area of the beam pattern. The left edge of the high intensity area should be even with the vertical line corresponding to the headlamp under adjustment. If the left edge of the high intensity area is not even with the vertical line, follow the next step to adjust it.


37


2006 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)


Lights • Aerodynamic: Locate the horizontal adjuster (1) for each headlamp.


Turn it clockwise or counterclockwise, to place the left edge of the high intensity area even with the vertical line corresponding to the headlamp under adjustment. • Sealed beam: Locate the horizontal adjuster (2) for each headlamp. Turn it clockwise or counterclockwise, to place the left edge of the high intensity area even with the vertical line corresponding to the headlamp under adjustment.


TURN SIGNAL CONTROL • Push down to activate the left • Push up to activate the right turn


turn signal.


signal.


INTERIOR LAMPS


is in the ON position


Cargo and dome lamps with rear headliner Rear cargo lamps equipped with an ON/OFF/DOOR control will light when: • doors are closed and the control • control is in the DOOR position • headlamp control is rotated fully counterclockwise When the control is in the OFF position, it will not illuminate when you open the doors or fully rotate the headlamp control.


and any door is open


38


2006 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)


Lights


Third row courtesy/reading/cargo lamps The dome portion of the lamp, the center light, can be turned on when the headlamp control is rotated fully counterclockwise or when any door is opened.


With the ignition key in the ACC or ON position, the rear dome lamp can be turned ON or OFF by sliding the control.


Front and rear courtesy/reading lamps The dome portion of the lamp, the center light, can be turned on when the headlamp control is rotated fully counterclockwise or when any door is opened. The reading lamp portion, the two outer lights, can only be toggled on and off at the lamp. BULB REPLACEMENT


Headlamp Condensation The headlamps are vented to equalize pressure. When moist air enters the headlamp(s) through the vents, there is a possibility that condensation can occur. This condensation is normal and will clear within 45 minutes of headlamp operation. Replacing exterior bulbs Check the operation of all the bulbs frequently. Using the right bulbs Replacement bulbs are specified in the chart below. Headlamp bulbs must be marked with an authorized “D.O.T.” for North America and an “E” for Europe to ensure lamp performance, light brightness and pattern and safe visibility. The correct bulbs will not damage the lamp assembly or void the lamp assembly warranty and will provide quality bulb burn time.


39


2006 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)


Lights


Function


Number of


bulbs


Trade number


9007


H5054


4157K or 3157K


Headlamps (sealed beam) Headlamps (aerodynamic) Park lamp and turn signal (front) Back-up lamps License plate lamp Stop/tail/turn/side marker lamp High-mount brakelamp Cargo lamp Dome lamp (standard) Map/reading lamp All replacement bulbs are clear in color except where noted. To replace all instrument panel lights - see your authorized dealer


912
211-2
912
211-2


3457K or 3357K


3156K or 3156


168


Replacing headlamp bulbs (aerodynamic) 1. Make sure headlamp switch is in the OFF position and open the hood. 2. Push each clip tab toward the engine compartment and lift upward to the stop position, then remove the headlamp assembly.


3. Disconnect the electrical connector from the bulb by pulling rearward.


40


2006 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)


Lights


4. Remove the bulb retaining ring by rotating it counterclockwise, and slide the ring off the plastic base.


5. Pull the bulb straight out.


Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated.


Note: If the bulb is accidentally touched, it should be cleaned with alcohol before being used. To install the new bulb, follow the removal procedures in reverse order. Replacing headlamp bulbs (sealed beam) 1. Make sure headlamp switch is in the OFF position and open the hood. 2. Remove the two headlamp screws and bezel from the headlamp housing.


41


2006 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)


Lights


3. Remove the four headlamp bulb retaining screws and the retaining ring. 4. Remove the headlamp. 5. Disconnect the electrical connector from the bulb and remove the bulb.


To install the new bulb, follow the removal procedures in reverse order. Replacing front parking lamp/turn signal bulbs 1. Make sure the headlamp control is in the OFF position. 2. Remove two screws and pull lamp assembly away from the vehicle. 3. Rotate the bulb socket counterclockwise and remove. 4. Carefully pull the bulb straight out of the socket. To complete installation, follow the removal procedures in reverse order.


Replacing high-mount brakelamp bulbs The interior cargo lamp (if equipped), on vehicles without a rear headliner, will have to be removed from under the high-mount brakelamp assembly located inside the vehicle. Then: 1. Remove the two screws from the high-mount brakelamp assembly and lift the lamp from the vehicle. 2. Remove the bulb socket from the lamp assembly by turning counterclockwise. 3. Carefully pull the bulb straight out of the socket.


To install the new bulb, follow the removal procedure in reverse order.


42


2006 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)


Lights


Replacing license plate lamp bulbs 1. Turn the headlamp switch to OFF and then remove the two screws and the license plate lamp assembly from the rear door. 2. Remove bulb socket from lamp assembly by turning counterclockwise. 3. Pull the bulb out from socket and push in the new bulb.


To install the new bulb, follow the removal procedures in reverse order. Replacing tail lamp/turn/backup lamp bulbs 1. Turn the headlamp switch to the OFF position and then remove the four screws and the lamp assembly from vehicle.


2. Rotate bulb socket counterclockwise and remove from lamp assembly. 3. Carefully pull the bulb straight out of the socket and push in the new bulb.


To install the lamp, follow the removal procedures in reverse order.


43


2006 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)


Driver Controls


MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you to increase the speed of the wipers; rotate towards you to decrease the speed of the wipers.


Windshield washer: Push the end of the stalk: • briefly: causes a single swipe of the wipers without washer fluid. • a quick push and hold: the wipers


will swipe three times with washer fluid.


• a long push and hold: the wipers and washer fluid will be activated for up to ten seconds.


TILT STEERING WHEEL To adjust the steering wheel: 1. Pull and hold the steering wheel release control toward you. 2. Move the steering wheel up or down until you find the desired location. 3. Release the steering wheel release control. This will lock the steering wheel in position.


Never adjust the steering wheel when the vehicle is moving.


44


2006 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)


Driver Controls


OVERHEAD CONSOLE (IF EQUIPPED) The appearance of your vehicle’s overhead console will vary according to your option package.


Storage compartment (if equipped) Press the release on the door to open the storage compartment. The storage compartment may be used to secure sunglasses or a similar object.


Installing a garage door opener (if equipped) The storage compartment can be converted to accommodate a variety of aftermarket garage door openers: 1. Place VELCRO威 hook onto side of aftermarket transmitter opposite of actuator control. 2. Place the transmitter into storage compartment, control down.


3. Place the provided height adaptors onto the back of the GARAGE control as needed. 4. Press the GARAGE control to activate the transmitter.


2006 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)


45


Driver Controls


Electronic compass/temperature display (if equipped)


Outside air temperature The outside temperature display is contained in the overhead console. The temperature display can be turned off and on by pressing the SELECT control on the overhead console. The temperature can be displayed in Centigrade or Fahrenheit by pressing the SELECT control. If the outside temperature falls below 3°C (38°F), the display will alternate from “ICE” to the outside temperature at a two second rate for one minute. Compass The compass display is contained in the overhead console. The vehicle heading is displayed as one of N, NE, E, SE, S, SW, W and NW. The compass reading may be affected when you drive near large buildings, bridges, power lines and powerful broadcast antenna. Magnetic or metallic objects placed in or on the vehicle may also affect compass accuracy. Adjustments may need to be made to the zone and calibration of the compass.


73˚ NW


23


15


14
13
12


7 8 9 1011


Compass zone adjustment 1. Determine which magnetic zone you are in by referring to the zone map. 2. Turn the ignition to the ON position.


46


2006 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)


Driver Controls


3. Press and hold the SELECT control until VAR appears in the display, then release. The display should show the current zone number. 4. Press the SELECT control until the desired zone number appears. The display will flash and then return to normal operation. The zone is now updated. Compass calibration adjustment Perform this adjustment in an open area free from steel structures and high voltage lines: • Press and hold the SELECT control until CAL appears in the display (approximately eight seconds) and release. • Drive the vehicle slowly (less


9 VAR


CAL


than 5 km/h [3 mph]) in circles until CAL indicator turns off in about 2–3 complete circles.


• The compass is now calibrated. AUXILIARY POWER POINT (12VDC) Power outlets are designed for accessory plugs only. Do not insert any other object in the power outlet as this will damage the outlet and blow the fuse. Do not hang any type of accessory or accessory bracket from the plug. Improper use of the power outlet can cause damage not covered by your warranty. The auxiliary power point is located on the instrument panel. A second power point (if equipped) is located behind the driver’s seat on the upper trim panel. Do not use the power point for operating the cigarette lighter element (if equipped). To prevent the fuse from being blown, do not use the power point(s) over the vehicle capacity of 12 VDC/180W.


47


2006 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)


Driver Controls


To prevent the battery from being discharged, do not use the power point longer than necessary when the engine is not running. Always keep the power point caps closed when not being used. Cigar/Cigarette lighter (if equipped) Do not plug optional electrical accessories into the cigarette lighter socket. Do not hold the lighter in with your hand while it is heating, this will damage the lighter element and socket. The lighter will be released from its heating position when it is ready to be used. Improper use of the lighter can cause damage not covered by your warranty.


POWER WINDOWS (IF EQUIPPED)


Do not leave children unattended in the vehicle and do not let children play with the power windows. They may seriously injure


themselves.


When closing the power windows, you should verify they are free of obstructions and ensure that children and/or pets are not in


the proximity of the window openings.


Press and hold the bottom part of the rocker switch to open the window. Press and hold the top part of the rocker switch to close the window.


Accessory delay With accessory delay, the window switches and radio may be used for up to ten minutes after the ignition switch is turned to the OFF position, or until any door is opened.


48


2006 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)


Driver Controls


to adjust the left to adjust the right


POWER SIDE VIEW MIRRORS (IF EQUIPPED) To adjust your mirrors: 1. Select mirror or mirror. 2. Move the control in the direction you wish to tilt the mirror. 3. Return to the center position to disable the adjust function.


Spotter mirror Note: New spotter mirrors may be stiff, requiring several cycles before the spotter adjustment effort eases. Standard mirror The spotter mirror only can be tilted from top to bottom. Move the lower mirror manually up/down to increase side and rear visibility. Apply pressure only in the center of the spotter mirror along the top or bottom edges to adjust the tilt feature. Do not apply any force on the left or right edges of the standard mirror spotter section, as this may lead to a mirror fracture. Telescoping mirror The spotter mirror has a swivel that allows it to tilt up and down, and also to tilt left and right to increase side and rear visibility.


49


2006 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)


Driver Controls


Fold-away mirrors The mirrors can be manually folded forward or backwards for narrow spaces like driving through an automatic car wash or backing out of a garage with the trailer tow mirror.


The telescoping feature (if equipped) allows the mirror to extend approximately 3.15 inches (80 mm). This feature is especially useful to the driver when towing a trailer.


SPEED CONTROL (IF EQUIPPED) With speed control set, you can maintain a speed of 30 mph (48 km/h) or more without keeping your foot on the accelerator pedal. Speed control does not work at speeds below 30 mph (48 km/h).


Do not use the speed control in heavy traffic or on roads that are winding, slippery or unpaved.


50


2006 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)


Setting speed control The controls for using your speed control are located on the steering wheel for your convenience. 1. Press the ON control and release it. 2. Accelerate to the desired speed.


3. Press the SET ACCEL control and release it. 4. Take your foot off the accelerator pedal. Note: • Vehicle speed may vary


momentarily when driving up and down a steep hill.


Driver Controls


RES


SET


ACCEL


COAST


• If the vehicle speed increases above the set speed on a downhill, you • If the vehicle speed decreases more than 10 mph (16 km/h) below


may want to apply the brakes to reduce the speed.


your set speed on an uphill, your speed control will disengage.


Resuming a set speed Press the RES (resume) control and release it. This will automatically return the vehicle to the previously set speed. The RES control will not work if the vehicle speed is not faster than 30 mph (48 km/h).


RES


SET


ACCEL


COAST


51


2006 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)


Driver Controls


Increasing speed while using speed control There are two ways to set a higher speed: • Press and hold the SET ACCEL control until you get to the desired speed, then release the control. You can also use the SET ACCEL control to operate the Tap-Up function. Press and release this control to increase the vehicle set speed in increments by 1 mph (1.6 km/h).


• Use the accelerator pedal to get to the desired speed. When the


vehicle reaches that speed press and release the SET ACCEL control.


ACCEL


COAST


RES


SET


Reducing speed while using speed control There are two ways to reduce a set speed: • Press and hold the COAST control until you get to the desired speed, then release the control. You can also use the COAST control to operate the Tap-Down function. Press and release this control to decrease the vehicle set speed in increments by 1 mph (1.6 km/h).


ACCEL


COAST


RES


SET


• Depress the brake pedal until the desired vehicle speed is reached, press the SET ACCEL control.


RES


SET


ACCEL


COAST


52


2006 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)


Driver Controls


Turning off speed control There are two ways to turn off the speed control: • Depress the brake pedal. This will


not erase your vehicle’s previously set speed.


• Press the speed control OFF


control.


Note: When you turn off the speed control or the ignition, your speed control set speed memory is erased.


53


2006 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)


Locks and Security


KEYS The key operates all locks on your vehicle. You should always carry a second key with you in a safe place in case you require it in an emergency. Your keys are coded to your vehicle; using a non-coded key will not permit your vehicle to start. If you lose your dealer supplied keys, replacement keys are available through your authorized dealer. POWER DOOR LOCKS (IF EQUIPPED) Press U to unlock all doors and L to lock all doors.


Memory lock If you lock your doors with the power lock switch or the remote transmitter while the sliding door is open, the door will automatically lock after it is closed. Back cargo door lock (if equipped) The passenger side rear cargo door has a power door lock control mounted on the inside of the door. When this lock is pressed, all doors will lock/unlock.


REMOTE ENTRY SYSTEM (IF EQUIPPED) This device complies with part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.


54


2006 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)


Locks and Security


Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. The typical operating range for your remote entry transmitter is approximately 33 feet (10 meters). A decrease in operating range could be caused by: • weather conditions, • nearby radio towers, • structures around the vehicle, or • other vehicles parked next to your vehicle. The remote entry system allows you to lock or unlock all vehicle doors without a key. Note: • The lock and unlock features


work when the ignition is in any position. • The panic feature is active when the ignition is in either the 1
(ACCESSORY), 2 (LOCK) or 3
(OFF) positions.


and release again within three seconds to unlock all the


and release to unlock the driver’s door. Note: The interior


If there are problems with the remote entry system, make sure to take ALL remote entry transmitters with you to the authorized dealer in order to aid in troubleshooting the problem. Unlocking the doors 1. Press lamps will illuminate. 2. Press doors. Locking the doors and release to lock all the doors. 1. Press 2. Press and release again within three seconds to confirm that all the doors are closed and locked. Note: The doors will lock again, and the horn will chirp once. Sounding a panic alarm Press to activate the alarm. Press the control again, or turn the ignition to the 1 (ACCESSORY) or 4 (ON) position to deactivate the alarm.


55


2006 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)


Loading...
x