1997 Ford Contour Owners Manual

File:04cdaso.ex Update:Thu Sep 12 10:59:17 1996

%*[AS21926(ALL)09/95]

[AS21927(ALL)03/94]

*[AS21928(ALL)03/96] *[AS21929(ALL)08/95] *[AS21930(ALL)10/95] *[AS21950(ALL)02/96]

*[AS21975(ALL)02/96]

*[AS22100(ALL)03/96] *[AS22225(ALL)02/96]

Electronic Stereo and Stereo Cassette Radios Both the Electronic Stereo Radio and Cassette Radio offer full electronic tuning with new soft touch controls. Using the Controls on Your New Radio

How to turn the radio on and adjust the volume

Press the “POWER” button to turn the radio on. Press it again to turn it off.

Press the right (+) side of the “VOLUME” button to increase the volume. Press the left (Ҁ) side of the button to decrease the volume. Illuminated bars in the display show the relative volume level.

NOTE: If the volume level is set above a certain listening

level when the ignition switch is turned off, when the ignition switch is turned back on, the volume will come back to a “nominal” listening level. However, if the radio power is turned off, the volume will remain in the position it was set at when radio power was switched off.

Selecting the AM or FM frequency band

Push the “AM/FM” button to select the desired frequency band. Pushing the button more than once will alternate between AM, FM1 and FM2. These functions are used with the station memory buttons described under How to tune radio stations.

38

File:04cdaso.ex Update:Thu Sep 12 10:59:17 1996

*[AS22300(ALL)02/96] *[AS22500(ALL)03/96] *[AS22600(ALL)08/95]

*[AS22700(ALL)03/96]

*[AS22704(ALL)04/96] *[AS22708(ALL)09/95]

%*[AS22710(ALL)02/96] *[AS22730(ALL)02/96] *[AS22740(ALL)02/96]

*[AS22750(ALL)03/96]

Electronic Sound Systems

How to tune radio stations (Stereo Radio) n Using the “TUNE” function

You can change the frequency up or down one increment at a time by pressing and releasing either the right (+) or left (Ҁ) side of the “TUNE” button. To change frequencies quickly, press and hold down either the right or left side of the “TUNE” button.

Manual tuning adjusts your radio to any allowable broadcast frequency, whether or not a station is present on that frequency. (See All About Radio Frequencies in this section.)

n Using the “SEEK” function

This feature on your radio allows you to automatically select listenable stations up or down the frequency band. Press the right (a) side of the “SEEK” button to select the next listenable station up the frequency band. Press the left (b) side of the button to select the next listenable station down the frequency band. By holding the button down, listenable stations can be passed over to reach the desired station.

How to tune radio stations (Stereo Cassette Radio) n Using the “AMS” function to manually tune your radio

(Stereo Cassette Radio)

You can change the frequency up or down one increment at a time by first pressing the “AMS” button (display shows “TUNE”) then within approximately five seconds pressing and releasing either the right a or left b side of the “SEEK” button. To change frequencies quickly, press and hold down either the right or left side of the “SEEK” button.

Manual tuning adjusts your radio to any allowable broadcast frequency, whether or not a station is present on that frequency. (See All About Radio Frequencies in this section.)

39

File:04cdaso.ex Update:Thu Sep 12 10:59:17 1996

*[AS22800(ALL)04/96] *[AS22900(ALL)09/95]

*[AS23160(ALL)02/96] *[AS23170(ALL)06/95]

*[AS23200(ALL)02/96] *[AS23325(ALL)10/95]

*[AS23400(ALL)08/95] *[AS23525(ALL)03/96] *[AS23700(ALL)10/95]

*[AS23800(ALL)10/95] *[AS23900(ALL)03/96]

n Using the “SEEK” function

This feature on your radio allows you to automatically select listenable stations up or down the frequency band. Press the right (a) side of the “SEEK” button to select the next listenable station up the frequency band. Press the left (b) side of the button to select the next listenable station down the frequency band. By holding the button down, listenable stations can be passed over to reach the desired station.

n Using the “SCAN” function (Stereo Cassette Radio)

Press the “SCAN” button to enter the scan mode. The radio will begin scanning up the frequency band, stopping on each listenable station for approximately a five-second sampling. This continues until you press the “SCAN” button a second time. The display flashes “AM” or “FM.” n Setting the Station Memory Preset buttons

Your radio is equipped with 6 station memory buttons. These buttons can be used to select up to 6 preset AM stations and 12 FM stations (6 in FM1 and 6 in FM2).

Follow the easy steps below to set these buttons to the desired frequencies:

1. Select a band, then select a frequency.

2. Press one of the memory preset buttons and hold the button until the sound returns. That station is now held in memory on that button.

3. Follow the two steps above for each station memory preset

button you want to set.

NOTE: If the vehicle’s battery is disconnected, the clock and station memory preset buttons will need to be reset.

40

File:04cdaso.ex Update:Thu Sep 12 10:59:17 1996

*[AS24000(ALL)10/95] *[AS24100(ALL)02/96] *[AS24225(ALL)02/96]

*[AS24300(ALL)02/96] *[AS24425(ALL)02/96]

*[AS24600(ALL)02/96] *[AS24725(ALL)02/96]

*[AS24800(ALL)04/96] *[AS24925(ALL)02/96]

*[AS24950(ALL)10/95]

Electronic Sound Systems

Adjusting the tone balance and speaker output of your radio n Increasing or decreasing bass response

Push the “AUDIO” button repeatedly until the display reads “BASS.” Push the right (+) side of the “VOLUME” button to increase bass (more “lows”), and push the left (Ҁ) side to decrease bass (less “lows”).

n Increasing or decreasing treble response

Push the “AUDIO” button repeatedly until the display reads “TREB.” Push the right (+) side of the “VOLUME” button to increase the treble (more “highs”), and push the left (Ҁ) side to decrease treble (less “highs”).

n Adjusting speaker balance

Balance control allows you to adjust the sound distribution between the right and left speakers. Push the “AUDIO” button repeatedly until the display reads “BAL.” Push the right (+) side of the “VOLUME” button to shift the sound to the right speakers, and push the left (Ҁ) side to shift the sound to the left speakers.

n Adjusting speaker fader

Fade control allows you to adjust the sound distribution between the front and rear speakers. Push the “AUDIO” button repeatedly until the display reads “FADE.” Push the right (+) side of the “VOLUME” button to shift the sound to the front speakers, and push the left (Ҁ) side to shift the sound to the rear speakers.

NOTE: Illuminated bars in the display show relative levels of bass and treble, and positions of speaker balance and fader functions (left to right, front to rear).

41

File:04cdaso.ex Update:Thu Sep 12 10:59:17 1996

%*[AS25000(ALL)04/96] *[AS25400(ALL)09/95] *[AS25500(ALL)08/95] *[AS25600(ALL)08/95]

*[AS25700(ALL)12/95] *[AS25800(ALL)06/95]

*[AS25920(ALL)08/95] *[AS25930(ALL)03/96]

*[AS25950(ALL)09/95] *[AS26000(ALL)04/96] *[AS26100(ALL)08/95] *[AS26200(ALL)04/96] *[AS26900(ALL)08/95] *[AS27000(ALL)02/96]

Using the Controls of Your Cassette Tape Player

NOTE: Radio power must be on to use the cassette tape

player.

How to insert a tape

Insert a cassette (with the open edge to the right) firmly into the tape door opening, making sure the cassette is completely in and “seated.”

How to locate a desired track on the tape

NOTE: The tape track or side number indicated in the display

does not necessarily correspond to the tape track or side number on the cassette label. It is used only to indicate when the tape mechanism reverses tracks.

n Using the Automatic Music Search (“AMS”)

Press and hold the “AMS” button (“AMS” will appear in the display). Then, push the left h button to rewind to the beginning of the current selection or press the right g button to fast forward to the beginning of the next selection. n Fast forwarding the tape

Push the right g button to fast forward the tape.

n Rewinding the tape

Push the left h button to rewind the tape.

n How to change the side of the tape being played

The alternate track (other side) of the tape can be selected at any time by pushing both fast-wind buttons h and g at the same time.

42

File:04cdaso.ex Update:Thu Sep 12 10:59:17 1996

*[AS27100(ALL)08/95] *[AS27250(ALL)04/96] *[AS27300(ALL)02/96] *[AS27400(ALL)09/95]

*[AS27550(ALL)05/95] *[AS27600(ALL)04/96] *[AS27700(ALL)08/95] *[AS27750(ALL)04/96]

*[AS27800(ALL)08/95]

*[AS27900(ALL)08/95]

*[AS28001(ALL)08/95]

*[AS28101(ALL)08/95]

*[AS28200(ALL)08/95]

Electronic Sound Systems

How to eject the tape To stop the tape and eject the cassette, press the eject (i) button. The radio will resume playing. Using the Dolby쑓 B noise reduction feature NOTE: Noise reduction system manufactured under license

from Dolby Labs Licensing Corporation. “Dolby” and double-D symbol are trademarks of Dolby Laboratories Licensing Corporation.

Push station memory button 3 to activate Dolby쑓 B Noise Reduction. Tips on Caring for the Cassette Player and Tapes In order to keep your cassette tape player performing the way it was meant to, read and follow these simple precautions: n Using a Ford Cassette Cleaning Cartridge or equivalent to

clean the tape player head after 10-12 hours of play will help maintain the best playback sound and proper tape operation.

n Only cassettes that are 90 minutes long or less should be

used. Tapes longer than 90 minutes are thinner and subject to breakage or may jam the tape player mechanism.

n Protect cassettes from exposure to direct sunlight, high

humidity and extreme heat or cold. If they are exposed to extreme conditions, allow them to reach a moderate temperature before playing.

n If a tape is loose inside the cassette, tighten it before playing by putting your finger or a pencil into one of the holes and turning the hub until the tape is tight.

n Loose labels on cassette tapes can become lodged in the

mechanism. Remove any loose label material before inserting a cassette.

n Do not leave a tape in the cassette tape player when not in use. High heat in the vehicle can cause the cassette to warp.

43

File:04cdaso.ex Update:Thu Sep 12 10:59:17 1996

%*[AS28300(ALL)04/96] *[AS28400(ALL)04/96]

*[AS28450(ALL)04/96] *[AS28500(ALL)04/96]

*[AS28600(ALL)04/96]

*[AS28700(ALL)04/96]

*[AS35200(ALL)04/96] *[AS35300(ALL)08/95] *[AS35400(ALL)08/95] *[AS35500(ALL)08/95]

Using the Power Antenna

The power antenna will automatically rise when your radio is turned on and the ignition is in the ON or ACC position. It will lower when either the radio or the ignition is turned off.

Power antenna maintenance and care n Never drive your vehicle through a car wash with the power

antenna mast extended. This can cause damage to the antenna mast, which is not covered under warranty. Turn off your radio and/or the vehicle. This will automatically retract the antenna.

n If your power antenna mast ever becomes damaged, the

mast may not extend or retract properly which might limit reception performance. In this case, it is not necessary to replace the entire power antenna assembly. A replacement mast can be obtained from your dealership for a nominal fee. n Occasionally, the power antenna mast should be wiped clean

with mild soap and water or denatured alcohol. This prevents debris from accumulating on the mast which can cause excessive wear and decrease the power antenna life. Never use petroleum-based products to clean your antenna mast.

Common Radio Reception Conditions Several conditions prevent FM reception from being completely clear and noise-free, such as the following:

1. Distance/Strength

The strength of the FM signal is directly related to the distance the signal must travel. The listenable range of an average FM signal is approximately 25 miles (40 kilometers). Beyond this distance, the radio is operating in a fringe area and the signal becomes weaker.

44

File:04cdaso.ex Update:Thu Sep 12 10:59:17 1996

*[AS35600(ALL)08/95] *[AS35700(ALL)08/95]

*[AS36850(ALL)04/95] *[AS36900(ALL)08/95]

%*[AS37000(ALL)08/95] *[AS37050(ALL)07/90] *[AS37100(ALL)08/95]

*[AS37150(ALL)07/90] *[AS37200(ALL)04/96]

Electronic Sound Systems

2. Terrain

The terrain (hilly, mountainous, tall buildings) of the area over which the signal travels may prevent the FM signal from being noise-free.

3. Rounded off frequencies

Some FM radio stations advertise a “rounded-off” frequency which is not the frequency they actually broadcast on. For example, a radio station that is assigned a frequency of 98.7
MHz may call itself “Radio 99” even though 99.0 MHz is not an allowable FM broadcast frequency. Important Warranty and Service Information n Warranty

Your sound system is warranted for three years or 36,000 miles (60,000 kilometers), whichever comes first. Consult your vehicle warranty booklet for further information. Ask your dealer for a copy of this limited warranty. n Service

At Ford, we stand behind our audio systems with a comprehensive service and repair program. If anything should go wrong with your Ford audio system, return to your dealer for service. There is a nationwide network of qualified Ford authorized repair centers to assist you.

45

File:05cdcfo.ex Update:Fri Sep 13 08:48:17 1996

%*[CF00200(ALL)03/96] [CF00300(ALL)12/95]

[CF00400(ALL)12/95]

[CF00500(ALL)04/96] *[CF00600(ALL)12/95] [CF00700(ALL)12/95] [CF00800(ALL)12/95]

[CF00900(O )05/96]

10-1/2 pica

art:0001181-C [CF01100(ALL)12/95]

Controls and Features

The Climate Control Systems Your vehicle has one of the following: n Heating Only System (Without Air Conditioning) n Heating and Air Conditioning System If you are not sure which system your vehicle has, see the diagrams on the following pages. Heating Only System The control for your heater system is located at the center of the instrument panel below the radio. The heater will operate only when the ignition key is turned to the ON position. Your heater will heat and/or ventilate your vehicle interior depending on the function selector knob position and temperature you select. The function selector knob allows you to select heating or ventilation and determine where the air will be directed. The temperature control knob setting determines the temperature of the air that flows into the vehicle.

The control for the heating only system

To turn your heater system on, select any position except OFF. This will turn the fan on and allow air flow into the vehicle. To turn your heater off, select OFF. This will turn the fan off and stop air flow from coming into the vehicle.

47

File:05cdcfo.ex Update:Fri Sep 13 08:48:17 1996

[CF01200(ALL)12/95]

[CF01300(ALL)05/96]

*[CF01400(ALL)03/96] [CF01500(ALL)05/96]

[CF01600(ALL)04/96] [CF01700(ALL)12/95] [CF01800(ALL)05/96]

[CF01900(ALL)12/95] [CF02000(ALL)12/95]

*[CF02100(ALL)03/96] [CF02200(ALL)12/95]

Your vehicle also has small demister openings on each front door near the window. This allows a small amount of air flow to be directed onto the door glass to reduce fogging whenever the heater system is operating. The temperature control is located at the right side of the control with a broken RED and BLUE band around the top and sides. The all RED part of the band (full right) is the heat or warmer area. The all BLUE area (full left) is the cool or unheated temperature area. Any position selected between full right and full left will give a temperature between the two extreme temperatures. The cool temperature you select will not be cooler than the outside temperature if your vehicle is not equipped with an air conditioner. H Fan speed adjustment The H (left) control is the fan speed control which controls the volume of air flow. Rotate the H control to HI to increase fan speed and increase the amount of air entering the vehicle. Four fan speed positions are available and are indicated by LO, two single dots and HI beside the H control. Air flow selections PANEL Use PANEL to bring outside air through the instrument panel registers. You can heat the air in this position by rotating the temperature control into the RED area. The air CANNOT be cooled below the outside temperature regardless of the temperature control setting. PNL/FLR Select PNL/FLR to get air flow to the floor and through the instrument panel registers at the same time. This selection can be used to either heat or ventilate your vehicle. FLOOR Air flow will be to the floor when FLOOR is selected. The air cannot be cooled in the FLOOR position but can be heated by rotating the temperature control knob into the RED area.

48

File:05cdcfo.ex Update:Fri Sep 13 08:48:17 1996

[CF02300(ALL)12/95]

[CF02400(ALL)12/95]

*[CF02500(ALL)03/96] [CF02600(ALL)05/96]

*[CF02700(ALL)01/96] [CF02800(ALL)12/95]

[CF02900(ALL)12/95]

[CF03000(O )05/96]

10-1/2 pica

art:0001192-C

Controls and Features

FLR/DEF Select FLR/DEF to get air to the floor and windshield defrosters at the same time. V DEF Select V DEF to obtain maximum air flow to the windshield. Rotate the temperature control into the RED area for the air temperature required to defrost. Rotate the H control to increase the air flow. Heating and Air Conditioning System Heating, ventilation, defrosting and defogging are accomplished in the same way as with the heating only system. See “Heating Only System.” With the heating and air conditioning system, if the outside temperature is about 50˚F (10˚C) or warmer, the air will be dehumidified to remove moisture if you select FLR/DEF or V DEF.

The control for the heating and air conditioning system

49

File:05cdcfo.ex Update:Fri Sep 13 08:48:17 1996

[CF03200(ALL)12/95] *[CF03300(ALL)01/96] [CF03400(ALL)12/95]

*[CF03500(ALL)03/96] [CF03600(ALL)03/96]

[CF03700(ALL)12/95]

[CF03800(ALL)04/96]

[CF03900(ALL)12/95]

[CF04000(ALL)12/95]

*[CF04100(ALL)01/96]

[CF04200(ALL)12/95]

Air conditioning

A/C

Select A/C to get refrigerated outside air through the instrument panel registers. The A/C position is used for cooling except when extremely hot or fast cooling of the vehicle is needed. Then, select MAX A/C for fast cooling and return to A/C when you are comfortable.

MAX A/C

The MAX A/C position produces cool air more rapidly to provide faster cooling of your vehicle. This is possible because cooler air is drawn from inside the passenger area and refrigerated again instead of using warmer outside air. Using inside air will also make the fan sound louder, which is normal when using MAX A/C. The air flow will be from the instrument panel registers. Comfort tips

The following tips will help you to get the most satisfaction from your climate control system. n In humid weather, select V DEF before starting your

engine. This will help to prevent windshield fogging. After a few minutes of operation, you may select another function.

n To prevent humidity buildup inside your vehicle, always

drive with the climate control system turned on.

n Do not put objects under the front seats that interfere with

the flow of air to the back seat area.

n Remove any snow, ice, or leaves from the air intake area of

your heater and air conditioner system which could block the air intake. The intake area is located at the bottom of the windshield.

50

File:05cdcfo.ex Update:Fri Sep 13 08:48:17 1996

[CF04300(ALL)12/95]

[CF04400(ALL)04/96]

% [CF04500(ALL)03/96]

[CF04600(ALL)04/96]

[CF04700(ALL)12/95]

[CF04800(ALL)12/95]

6 pica art:0001180-C

[CF04900(ALL)12/95]

*[CF05000(ALL)01/96] *[CF05100(ALL)01/96]

Controls and Features

Passenger Compartment Air Filter (if equipped)

Your vehicle may have an air filter that removes pollen and road dust from outside air before it is directed to the interior of the vehicle. For maintenance of this filter, see the Maintenance and Care chapter. Rear Window Defroster (If equipped) The defroster for the rear window clears frost, fog, or thin ice from both the inside and outside of the rear window.

The button for the rear window defroster is on the instrument panel, to the right of the steering wheel.

The rear window defroster and heated side view mirrors

Clear away any snow that is on the rear window before using the defroster. With the engine running, push the defroster button.

After approximately 10 minutes, the defroster will turn off. If the window is still not clear, turn the defroster on again.

The defroster will turn off when the ignition key is turned to the OFF or START position.

51

File:05cdcfo.ex Update:Fri Sep 13 08:48:17 1996

%*[CF05200(ALL)03/96]

%*[CF05300(ALL)03/96] %*[CF05400(ALL)03/96] [CF05500(ALL)12/95]

[CF05600(O )04/96]

10-1/2 pica art:0001178-E

[CF05800(ALL)04/96]

[CF05900(ALL)04/96]

NOTE: Never use sharp instruments or window cleaners with

abrasives to clean the inside of your rear window. If you do, you may damage the heating elements that are bonded to the inside of the rear window and cause damage to the rear window defroster.

The Interior and Exterior Lights Turning On the Exterior Lights

To turn on your headlamps, parking lamps, and tail lamps, use the knob that is on the instrument panel, to the left of the steering wheel.

The knob for the exterior lights

To turn on the parking lamps, tail lamps, license plate lamps and side marker lamps, turn the knob clockwise to the first position.

To turn on the headlamps, parking lamps, tail lamps, license plate lamps and side marker lamps, turn the knob clockwise to the second position.

52

File:05cdcfo.ex Update:Fri Sep 13 08:48:17 1996

%*[CF06000(ALL)08/95] [CF06100(ALL)12/95]

[CF06200(ALL)12/95]

[CF06300(ALL)12/95] *[CF06400(ALL)03/96]

%*[CF06500(ALL)03/96] *[CF06600(ALL)03/96] *[CF06700(ALL)01/96]

[CF06750(ALL)04/96]

[CF06800(ALL)04/96]

[CF06900(ALL)04/96] *[CF07000(ALL)03/96]

[CF07100(ALL)12/95]

Controls and Features

Fog Lamps (If equipped)

The fog lamps act as a supplement to the low beam headlamps under limited visibility conditions such as rain, snow, dust or fog.

The fog lamps operate only when the low beam headlamps are on. To operate the fog lamps, turn the headlamp control knob to the second position (headlamps on) and pull the knob out. An indicator lamp will glow when the fog lamps are on.

To turn off, push the headlamp control knob in.

To maximize fog lamp bulb life, it is recommended that the fog lamp switch be turned off after each use prior to turning off the headlamps. Daytime Running Light System

(Canadian vehicles only)

The Daytime Running Light (DRL) system is designed to turn the high beam headlamps on, with a reduced light output and without illuminating the high beam indicator lamp in the instrument panel. The DRL system operates when all of the following conditions are met: n The vehicle’s parking brake is fully released. n The vehicle is “running.” n The headlamp system is in the OFF position.

The high beam indicator light on the instrument cluster will not be on.

A flashing high beam light in the instrument cluster indicates a failure in the DRL system circuit, like a burnt bulb or fuse.

53

File:05cdcfo.ex Update:Fri Sep 13 08:48:17 1996

*[CF07200(ALL)03/96]

%*[CF07300(ALL)01/96] [CF07400(ALL)12/95]

[CF07500(ALL)12/95]

[CF07600(ALL)12/95]

6 pica art:0001177-B

% [CF07700(ALL)12/95]

[CF07800(ALL)02/96]

[CF07900(ALL)12/95]

6 pica art:0001179-C

(cid:82)WARNING

The Daytime Running Light (DRL) system will not illuminate the tail lamps and parking lamps. Turn on your headlamps at dusk. Failure to do so may result in a collision.

Lighting Up the Interior and Instrument Panel When either front door is opened, the footwell lights and the door courtesy lights come on. The instrument panel lights, window control lights and door handle lights come on whenever the headlamp switch is turned from the OFF position. To dim the instrument panel lights, use the thumbwheel on the instrument panel to the right of the steering wheel.

Dimming the instrument panel lights Traction Control System (If equipped) This button turns the traction control system off and on. See the Driving Chapter for more information.

The button for the traction control system

54

File:05cdcfo.ex Update:Fri Sep 13 08:48:17 1996

%*[CF08000(ALL)03/96] [CF08100(O )12/95]

Clock

Controls and Features

7-1/2 pica art:0001220-B

*[CF08300(ALL)12/95] *[CF08400(ALL)12/95]

[CF08500(ALL)12/95]

%*[CF08600(ALL)05/96] [CF08700(ALL)12/95]

[CF08800(ALL)12/95] *[CF09000(ALL)05/96]

The digital clock

1. To set the hour, press and hold the hour button. When the

desired hour appears, release the button.

2. To set the minutes, press and hold the minute button. When

the desired minute appears, release the button.

3. To switch between a 12-hour clock and a 24-hour clock,

press both the hour and minute buttons at the same time. Reset the time as above.

Storage Compartments Your vehicle may have several storage compartments: n a coin holder on the instrument panel

The controls on the steering column and wheel are designed to give you easy access to the controls while you are driving.

55

File:05cdcfo.ex Update:Fri Sep 13 08:48:17 1996

*[CF09100(ALL)01/96] %*[CF09200(ALL)01/96] [CF09300(ALL)12/95]

Ignition Understanding the Positions of the Ignition

10-1/2 pica

art:0001185-D

[CF09400(ALL)12/95]

*[CF09500(ALL)01/96]

*[CF09600(ALL)12/95] *[CF09700(ALL)01/96] *[CF09800(ALL)01/96]

The positions of the key in the ignition

LOCK and ACCESSORY lock the gearshift for all vehicles with an automatic transaxle.

(cid:82)WARNING

LOCK position does not lock the gearshift on floor-mounted manual transaxle gearshifts. If the parking brake is not set and the gearshift is moved out of gear, your vehicle may move unexpectedly and injure someone.

The automatic transaxle gearshift must be in P (Park) to move the key to the LOCK position.

LOCK is the only position that allows you to remove the key. The LOCK feature helps to protect your vehicle from theft.

If your key is stuck in the LOCK position and will not turn, move your steering wheel left or right until the key turns freely.

56

File:05cdcfo.ex Update:Fri Sep 13 08:48:17 1996

[CF09900(ALL)12/95]

*[CF10000(ALL)01/96]

*[CF10100(ALL)01/96]

%*[CF10200(ALL)03/96] [CF10300(ALL)04/96]

[CF10400(ALL)04/96] *[CF10500(ALL)01/96] *[CF10600(ALL)01/96] [CF10700(ALL)12/95]

[CF10800(ALL)12/95]

Controls and Features

ACCESSORY allows some of your vehicle’s electrical accessories to operate while the engine is not running. For example, you can use ACCESSORY to turn on the radio without starting the engine.

ON allows you to test your vehicle’s warning lights (except the brake system warning light) to make sure they work before you start the engine. The key returns to the ON position once the engine is started and remains in this position while the engine runs.

START cranks the engine. Release the key once the engine starts so that you do not damage the starter. The key should return to ON when you release it. The START position also allows you to test the brake warning light. Removing the Key From the Ignition

Procedures for removing your key from the ignition vary, depending on whether your vehicle has an automatic or manual transaxle.

If your vehicle has an automatic transaxle:

1. Put the gearshift lever in P (Park).

2. Set the parking brake fully.

3. Rotate the ignition key to the LOCK position.

4. Remove the key from the ignition.

57

File:05cdcfo.ex Update:Fri Sep 13 08:48:17 1996

[CF10900(ALL)04/96]

[CF11000(ALL)04/96] *[CF11100(ALL)01/96] [CF11200(ALL)12/95]

[CF11300(ALL)12/95]

[CF11400(ALL)12/95] %*[CF11500(ALL)12/95] *[CF11600(ALL)01/96]

*[CF11700(ALL)03/96]

If your vehicle has a manual transaxle:

1. Put the gearshift lever in 1 (First).

2. Set the parking brake fully.

3. Rotate the ignition key to the LOCK position.

4. Remove the key from the ignition.

The steering wheel locks when the key is removed.

If the driver’s door is open while the key is still in the ignition, a warning chime sounds.

(cid:82)WARNING

Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park) (automatic transaxle) or in 1 (First) (manual transaxle).

(cid:82)WARNING

Do not leave children, unreliable adults, or pets unattended in your vehicle.

58

File:05cdcfo.ex Update:Fri Sep 13 08:48:17 1996

%*[CF11950(ALL)02/96] *[CF11975(ALL)02/96] *[CF12000(ALL)02/96] *[CF12100(ALL)03/96] *[CF12200(ALL)03/96] %*[CF12300(ALL)01/96] [CF12400(ALL)12/95]

10-1/2 pica

art:0001186-D *[CF12500(ALL)01/96]

*[CF12600(ALL)01/96] *[CF12700(ALL)01/96]

Controls and Features

The Turn Signal Lever You can use the turn signal lever on the left side of the steering column to: n operate the turn signals and cornering lamps n turn the high beams on/off n flash the lamps Turn Signals

The turn signal lever

Move the lever up to signal a right turn. Move it down to signal a left turn. The corresponding indicator light in the instrument cluster will flash.

If the turn signal stays on after you turn, move the lever back to the center (off) position.

For lane changes, move the lever far enough to signal but not to latch. The lever will return to the off position when you release it.

59

File:05cdcfo.ex Update:Fri Sep 13 08:48:17 1996

*[CF12800(ALL)08/95] [CF12900(ALL)12/95]

[CF13000(ALL)12/95]

*[CF13100(ALL)01/96]

%*[CF13200(ALL)01/96] [CF13300(ALL)04/96]

[CF13400(ALL)12/95]

10-1/2 pica

art:0001189-D

[CF13500(ALL)12/95]

High Beams and Flashing the Lamps

To turn on the high beams, turn the headlamp control knob to the headlamp ON position and push the turn signal lever away from you until it latches. When the high beams are on, the high beam indicator light on the instrument cluster comes on.

To turn off the high beams, pull the lever back to the off position.

To flash the headlamps, pull the lever toward you for a moment and then release it. The headlamps will flash whether the headlamp knob is in the on or off position. Windshield Wipers and Washer To turn on the windshield wipers, the ignition key must be turned to the ON position.

Using the windshield wiper

The windshield wipers can be set on high, low speed or interval wipe. Turn the ring on the lever to set a longer or shorter pause between wiping cycles.

60

File:05cdcfo.ex Update:Fri Sep 13 08:48:17 1996

*[CF13600(ALL)01/96] [CF13700(ALL)12/95]

[CF13800(ALL)12/95]

7-1/2 pica art:0001194-D

*[CF13900(ALL)08/95]

*[CF14000(ALL)01/96]

*[CF14100(ALL)03/96]

Controls and Features

Windshield Washer

When the lever is pulled to activate the windshield washer, the wipers operate for about three cycles after the spray stops.

Washing the windshield

Do not try to clean the windshield when the washer fluid container is empty or activate the washers at any time for more than 15 seconds continuously. This could damage the washer pump system.

(cid:82)WARNING

Always warm up the windshield with the defroster before you use the washer fluid. In freezing weather, the washer solution may freeze on the windshield and obscure your vision.

For information about refilling the washer fluid or replacing your windshield wiper blades, see Windshield washer fluid and Wipers in the Index.

61

File:05cdcfo.ex Update:Fri Sep 13 08:48:17 1996

%*[CF14200(ALL)03/96] *[CF14300(ALL)12/95]

[CF14400(ALL)12/95]

10-1/2 pica

Hazard Flasher The hazard flasher serves as a warning to other drivers to be careful when approaching or passing your vehicle.

art:0001193-A %*[CF14500(ALL)05/96] [CF14600(ALL)04/96]

Using the hazard flasher switch

Horn To sound the horn, push the pad in the center of the steering wheel. Check the horn regularly to be sure it operates properly.

62

File:05cdcfo.ex Update:Fri Sep 13 08:48:17 1996

Controls and Features

%*[CF14700(ALL)05/96] [CF14800(ALL)05/96]

Tilt Steering (If equipped)

(cid:82)WARNING

Never adjust the steering column/wheel when the vehicle is moving. You could lose control of the vehicle and injure someone.

[CF14900(ALL)05/96]

17-1/2 pica

art:0000269-D

[CF15000(ALL)05/96]

[CF15100(ALL)05/96]

The lever to tilt the steering wheel

To change the position of the steering wheel, pull down the knob on the bottom left-hand side of the column to extend the lever. Pull the lever toward you, unlocking the column.

Move the steering wheel up or down until you find the position you prefer. Push the lever away from you, locking the column in position. When you release the knob, the lever will retract.

63

File:05cdcfo.ex Update:Fri Sep 13 08:48:17 1996

%*[CF15200(ALL)03/96] [CF15225(ALL)02/96]

Speed Control (If equipped)

10-1/2 pica

art:0000262-D *[CF15250(ALL)05/96] [CF15275(ALL)05/96] *[CF15300(ALL)05/96] *[CF15600(ALL)05/96]

[CF15650(ALL)02/96]

%*[CF15675(ALL)05/96] *[CF15701(ALL)03/96] *[CF15800(ALL)05/96] [CF15901(ALL)05/96]

The speed control switches on the steering wheel

To Turn Speed Control On Press the on button. The speed of the vehicle cannot be automatically controlled until the vehicle speed is at or above 30 mph (48 km/h).

(cid:82)WARNING

Do not use the speed control in heavy traffic or on roads that are winding, slippery, or unpaved.

(cid:82)WARNING

Do not shift to N (Neutral) with the speed control on.

To Turn Speed Control Off Press the OFF switch. To Set a Speed With the speed control on, press the Set Accel switch to set and store the instantaneous vehicle speed.

64

File:05cdcfo.ex Update:Fri Sep 13 08:48:17 1996

*[CF16300(ALL)05/96]

[CF16400(ALL)02/96]

[CF16500(ALL)01/96]

[CF16700(ALL)05/96]

[CF16801(ALL)05/96]

[CF16901(ALL)05/96]

[CF17001(ALL)05/96]

[CF17101(ALL)05/96]

Controls and Features

If you drive up or down a steep hill, your vehicle may momentarily slow down or speed up, even though the speed control is on. This is normal. NOTE: If your vehicle is equipped with an automatic

transaxle, and if your speed increases above your set speed while driving in Overdrive on a downhill grade, you may want to turn the Overdrive off and use Drive. You may turn the Overdrive off by pressing the Transaxle Control Switch on the left side of the gearshift lever. This will reduce vehicle speed if it goes above your set speed on a downhill grade.

NOTE: If your vehicle is equipped with a 5-speed manual

transaxle, and if your speed increases above your set speed while driving in 5 (Fifth) gear on a downhill grade, you may want to shift to 4 (Fourth) gear to reduce vehicle speed. Depressing the clutch pedal cancels speed control, therefore speed control must be reset by pressing the SET/ACC or RES buttons. Speed control cannot reduce the vehicle speed if it goes above your set speed on a downhill grade.

To Speed Up Hold the Set Accel switch down and the vehicle will speed up without the need to depress the accelerator. When the switch is released, the system will maintain the speed reached. This speed becomes the new stored speed. The vehicle speed can also be increased by momentarily depressing the Set Accel switch (Tap up). Each tap will increase the speed by approximately 1 mph (1.6 km/h). To Slow Down Hold the Coast switch down and the vehicle will slow down under normal engine braking. When the switch is released, the system will maintain the speed reached. This speed becomes the new stored speed.

65

File:05cdcfo.ex Update:Fri Sep 13 08:48:17 1996

[CF17201(ALL)05/96]

[CF17301(ALL)03/96]

[CF17401(ALL)05/96]

[CF18800(ALL)02/96]

[CF18900(O )12/95]

[CF19000(O )12/95]

7-1/2 pica art:0001219-A

[CF19300(ALL)02/96]

[CF19400(ALL)12/95]

[CF19500(ALL)12/95]

*[CF19600(ALL)02/96]

The vehicle speed can also be decreased by momentarily depressing the Coast switch (Tap down). Each tap will decrease the speed by approximately 1 mph (1.6 km/h). Resume feature

The speed control system will be disengaged as soon as the brake or clutch pedal is depressed. To turn to the previously set speed, momentarily depress the RES switch. Dome Lamp Your vehicle has a dome lamp above the front seat. The switch on the dome lamp turns it on and off.

The switch on the dome lamp Dome lamp delay

Your vehicle may have a dome lamp delay. If you set the switch on the dome lamp to the 12-second delay position, the dome lamp will turn on when either front door is opened.

The dome lamp will turn off after 12 seconds or when the ignition key is turned to the ON or ACC position. It will not turn off if either front door is open or if you move the dome lamp switch to the ON position.

Your interior dome lamps and map lamps are plastic and should be cleaned with a mild detergent diluted in water. Rinse them with clear water.

66

File:05cdcfo.ex Update:Fri Sep 13 08:48:17 1996

[CF19700(ALL)02/96]

[CF19800(ALL)04/96]

[CF19900(ALL)12/95]

7-1/2 pica art:0001218-A

%*[CF20000(ALL)01/96] *[CF20100(ALL)03/96]

[CF20200(ALL)12/95]

Controls and Features

Turning On the Map Lamps (If equipped) Your vehicle may have a map lamp for the passenger and one for the driver.

Turning on the map lamps Moon Roof (If equipped) You can move the moon roof back to open the glass panel, or you can tilt it up to ventilate the vehicle.

The rocker type switch is used to open and close the moon roof. You must press and hold the switch until the desired position is reached. At open and closed positions, the motor will automatically turn off. Release the switch at this time to avoid motor damage.

67

File:05cdcfo.ex Update:Fri Sep 13 08:48:17 1996

[CF20300(ALL)12/95]

10-1/2 pica

art:0001187-A

[CF20400(ALL)12/95]

[CF20500(ALL)12/95]

*[CF20600(ALL)12/95] *[CF20700(ALL)12/95] *[CF20800(ALL)01/96]

The map lamps and the switch for the moon roof

To open the moon roof, press and hold the rear portion of the switch. The glass panel will move to the open position and stop.

To close the moon roof, press and hold the front portion of the switch. The glass panel will move to the closed position and stop.

To tilt the moon roof into vent position when the glass panel is closed, press the front portion of the switch.

To close from vent position, press and hold the rear portion of the switch.

Occasionally wiping the outside guide rail covers of the moon roof with a clean cloth will help keep the moon roof working properly.

68

File:05cdcfo.ex Update:Fri Sep 13 08:48:17 1996

[CF20900(ALL)12/95]

7-1/2 pica art:0001188-A

*[CF21000(ALL)01/96]

*[CF21100(ALL)01/96] *[CF21200(ALL)01/96]

[CF21300(ALL)04/96]

Controls and Features

The moon roof

(cid:82)WARNING

Do not let children play with the moon roof. They may seriously hurt themselves.

Sliding Shade

The moon roof has a sliding shade that you can manually open or close to block the sun when the glass panel is shut.

To close the sliding shade, pull the shade toward the front of the vehicle. The shade automatically opens when the moon roof is opened.

69

File:05cdcfo.ex Update:Fri Sep 13 08:48:17 1996

%*[CF21400(ALL)04/96] *[CF21500(ALL)12/95] [CF21600(ALL)12/95]

[CF21700(ALL)12/95]

10-1/2 pica

Sun Visors Illuminated Visor Mirror (If equipped)

Your vehicle may have lighted mirrors on the sun visors. The mirror is lit by sliding open the mirror cover.

art:0000588-B

The visor mirror

70

File:05cdcfo.ex Update:Fri Sep 13 08:48:17 1996

%*[CF21800(ALL)02/96] %*[CF21900(ALL)04/96] [CF22000(ALL)12/95]

[CF22100(ALL)12/95]

17-1/2 pica

art:0001247-A *[CF22200(ALL)01/96] [CF22300(ALL)12/95]

*[CF22400(ALL)04/96]

Controls and Features

Doors Childproof Locks for the Rear Doors In addition to standard or power locks, your vehicle has childproof locks for the rear doors. If you set these locks, the rear doors cannot be opened from the inside of the vehicle. The doors can still be opened from the outside if the doors are unlocked.

The childproof locks for the rear door To set the childproof lock on each rear door, open the rear door. Find the lever at the black label with word LOCKED in white letters. Move the lever toward the inside of the door. To release the childproof lock, open the rear door from the outside.

71

File:05cdcfo.ex Update:Fri Sep 13 08:48:17 1996

[CF22500(ALL)12/95] %*[CF22600(ALL)01/96] [CF22700(ALL)12/95]

[CF22800(ALL)12/95]

10-1/2 pica

art:0001250-B

Move the lever toward the outside of the door. Power Door Locks (If equipped)

If your vehicle has power door locks, the controls to lock the doors are on the trim panel of the front door. When you close the doors after you set the door locks, the doors remain locked. If the power mechanism fails, the manual door lock will automatically override the power controls.

The power door lock on the driver’s door

72

File:05cdcfo.ex Update:Fri Sep 13 08:48:17 1996

%*[CF23200(ALL)04/96] %*[CF23300(ALL)01/96] *[CF23400(ALL)12/95]

[CF23500(ALL)12/95]

[CF23600(ALL)12/95]

10-1/2 pica

art:0001191-B *[CF23700(ALL)01/96]

[CF23800(ALL)12/95]

[CF23900(ALL)12/95]

[CF24000(ALL)12/95]

Controls and Features

Windows Power Windows (If equipped)

Each door has a power control that opens and closes the window on that door. The driver’s door has a master control panel that operates all four windows.

In order to use your power window controls, the ignition switch must be in the ON position.

The master controls on the driver’s door

Do not let children play with the power windows.

(cid:82)WARNING

One-touch-down window

The one-touch-down feature allows you to completely open the driver’s window by briefly pressing and releasing the bottom of the window switch. To stop the window before it opens completely, press the switch again.

The one-touch feature only opens the window. To close the window, you must press and hold the top of the switch.

73

File:05cdcfo.ex Update:Fri Sep 13 08:48:17 1996

[CF24100(ALL)12/95]

[CF24200(ALL)12/95]

%*[CF24300(ALL)03/96] %*[CF24400(ALL)01/96] [CF24500(ALL)12/95]

[CF24600(ALL)12/95]

10-1/2 pica

Rear window lockout

To lock out the rear window switches with the master controls, slide the lockout switch to the left. To restore individual control, slide the switch to the right. Mirrors Side View Mirrors

The standard side view mirrors are manually adjusted by using the remote knobs. The knob on each door adjusts the mirror on that side of the vehicle. Move the control knob in the direction you want to move the mirror.

art:0000463-B

% [CF24700(ALL)12/95]

[CF24800(ALL)12/95]

The left side mirror control (right side similar)

Dual electric remote control mirrors (if equipped)

The control for adjusting the electric side view mirrors is on the instrument panel, to the left of the steering wheel.

74

File:05cdcfo.ex Update:Fri Sep 13 08:48:17 1996

[CF24900(ALL)12/95]

10-1/2 pica

art:0001182-B

[CF25000(ALL)12/95]

*[CF25100(ALL)12/95]

*[CF25200(ALL)05/96]

Controls and Features

Electric remote control mirror knob

Turn the knob back to the middle position to keep the mirror in place.

The side view mirror on the right is a convex mirror. This mirror gives you a wider view of the lanes on your right and behind you.

(cid:82)WARNING

The right side view mirror makes objects appear smaller and farther away than they actually are.

%*[CF25300(ALL)12/95]

Do not clean the housing or glass of any mirror with harsh abrasives, fuel or other petroleum-based cleaning products.

75

File:05cdcfo.ex Update:Fri Sep 13 08:48:17 1996

%*[CF25700(ALL)01/96] *[CF25800(ALL)12/95]

[CF25900(ALL)12/95]

Console Your vehicle may have a full console. The full console has the following features:

17-1/2 pica

art:0001175-C

[CF25903(ALL)02/96]

[CF25906(ALL)02/96]

The features on the full console Cupholder with Full Console

To raise the pop-up cup holder, push and release the cupholder door, then unfold the holder.

76

File:05cdcfo.ex Update:Fri Sep 13 08:48:17 1996

*[CF25930(ALL)12/95] [CF25940(ALL)02/96]

[CF25950(ALL)04/96]

[CF26200(ALL)01/96]

17-1/2 pica

Controls and Features

Floor Mats Positive retention floor mat (If equipped) (Standard in Canada)

Position the floor mat in the footwell. Place the mat eyelet over the pointed end of the retention post from the rear and rotate forward to install. Adjust the floor mat position to allow proper operation of accelerator pedal, brake pedal and clutch pedal.

art:0001344-A

[CF26300(ALL)01/96]

The positive retention floor mat

To remove, lift the floor mat just forward of the retention post and rotate it rearward to disengage it from the retention post.

77

File:05cdcfo.ex Update:Fri Sep 13 08:48:17 1996

%*[CF26500(ALL)04/96] [CF26600(ALL)12/95]

% [CF26700(ALL)12/95]

[CF26800(ALL)12/95]

[CF26900(ALL)12/95]

7-1/2 pica art:0000984-F

[CF27000(ALL)12/95]

[CF27100(ALL)12/95]

10-1/2 pica

art:0001485-A

Trunk To open the trunk manually, use the oval key. Remote Trunk Release (If equipped)

The remote trunk release is on the floor to the left of the driver’s seat.

The remote trunk release

You can disable the remote trunk release. If you depress the lever on the trunk latch that is marked in orange before closing the trunk, the trunk can only be opened with the key.

Disabling the remote trunk release

78

File:05cdcfo.ex Update:Fri Sep 13 08:48:17 1996

*[CF27200(ALL)05/96] *[CF27300(ALL)05/96]

[CF27400(ALL)12/95]

*[CF27500(ALL)01/96]

[CF27600(ALL)12/95]

10-1/2 pica

art:0001221-A %*[CF27700(ALL)02/96] *[CF27800(ALL)04/96] *[CF27900(ALL)04/96] *[CF28000(ALL)04/96]

Controls and Features

Remote Entry System (If equipped) If your vehicle has the remote entry system, you can lock and unlock the vehicle doors and open the trunk without using a key. The remote also has a personal alarm feature. The controls for the system are located on the hand held transmitter(s) that came with your vehicle.

The system will work with up to four transmitters. Additional transmitters can be ordered from your dealer.

The remote entry features only operate with the ignition in the OFF position.

Remote entry transmitter

Unlocking the doors and opening the trunk

To unlock the driver’s door, press the UNLOCK control.

To unlock the other doors, press the UNLOCK control a second time within five seconds of unlocking the driver’s door.

To open the trunk, press the TRUNK control.

79

File:05cdcfo.ex Update:Fri Sep 13 08:48:17 1996

[CF28100(ALL)05/96]

[CF28200(ALL)12/95]

*[CF28300(ALL)04/96] *[CF28400(ALL)04/96] *[CF28500(ALL)04/96]

%*[CF28600(ALL)03/96] [CF28700(ALL)05/96]

%*[CF28800(ALL)03/96] *[CF28900(ALL)01/96]

When you use the remote entry UNLOCK, TRUNK or PANIC controls, the illuminated entry system turns on the interior lights for 12 seconds. You can turn these lights off by turning the ignition to the ON position. The interior lights will not turn off if you have turned them on manually or if a door is open.

NOTE: The illuminated entry system will only work when

the dome light switch is in the “12” position.

Locking the doors

To lock all the doors, press the LOCK control.

If you would like a signal that the doors are being locked, press the LOCK control again within five seconds. The doors will lock again and the horn will beep. Activating the remote personal alarm

If you wish to activate the remote personal alarm, press the PANIC control. This will honk the horn and flash the low beam headlamps and tail lamps for approximately two minutes forty-five seconds. You can turn it off by pressing the PANIC control again on the same transmitter or by turning the ignition key to the ON position. Replacing the Batteries

The remote entry transmitter is powered by two coin type three-volt lithium 2016 batteries (included) that should last for several years of normal use. If you notice a significant decrease in operating range, the batteries should be replaced. Replacement batteries can be purchased at most pharmacies, watch stores or at your Ford or Lincoln-Mercury dealer.

80

File:05cdcfo.ex Update:Fri Sep 13 08:48:17 1996

*[CF29000(ALL)01/96]

[CF29100(ALL)12/95]

7-1/2 pica art:0001315-A

*[CF29200(ALL)01/96]

%*[CF29300(ALL)02/96] *[CF29400(ALL)01/96]

*[CF29500(ALL)01/96]

Controls and Features

NOTE: The operating range of the remote entry system can also be affected by weather conditions (such as very cold temperatures) or structures around the vehicle (buildings, other vehicles, radio towers, etc.). Typical operating range will allow you to be up to 33 feet (10
meters) away from your vehicle.

Replacing the batteries

The transmitter can be snapped apart to replace the batteries by twisting a thin coin between the two halves of the transmitter. DO NOT TAKE THE FRONT PART OF THE TRANSMITTER APART. When installing the new batteries, be sure to place the positive (+) side down as marked. Snap the two halves back together. Replacement/additional transmitters

In the event a transmitter is lost, return the remaining transmitters to your dealer for reprogramming of your remote entry system. This is necessary to prevent further unauthorized use of the lost transmitter.

Additional transmitters may be purchased from your dealer (remote entry system will work with up to four transmitters). Return your existing transmitters to your dealer so the remote entry system can be reprogrammed with your new and existing transmitters.

81

File:05cdcfo.ex Update:Fri Sep 13 08:48:17 1996

*[CF29600(ALL)01/96]

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

82

File:06cdsso.ex Update:Thu Sep 12 11:03:20 1996

%*[SS00200(ALL)01/96] %*[SS00300(ALL)02/96] *[SS00400(ALL)01/96] *[SS00500(ALL)01/96]

[SS00600(ALL)12/95]

[SS00700(ALL)12/95]

10-1/2 pica

Seating and Safety Restraints

Seats Head Restraints

If you use them properly, head restraints will help protect your head and neck in a collision.

A head restraint helps protect you best if you position it behind your head and not behind your neck.

If your vehicle has the four-way head restraint, you can adjust it in four directions. You can raise it two (2) inches (50 mm) from its normal position, or you can move it forward up to 60˚ until you reach the desired position.

art:0001216-A

The four-way head restraint

83

File:06cdsso.ex Update:Thu Sep 12 11:03:20 1996

%*[SS00800(ALL)12/95] [SS00900(ALL)12/95]

Manual Seats

10-1/2 pica

art:0001217-C *[SS01000(ALL)01/96]

*[SS01100(ALL)02/96]

Manual seat adjustment

(cid:82)WARNING

Never adjust the driver’s seat or seatback when the vehicle is moving.

(cid:82)WARNING

Always drive and ride with your seatback upright and the lap belt snug and low across the hips.

84

File:06cdsso.ex Update:Thu Sep 12 11:03:20 1996

%*[SS01600(ALL)12/95] [SS01700(ALL)12/95]

[SS01800(ALL)12/95]

13-1/2 pica

Seating and Safety Restraints

Power Seats (If equipped) If your vehicle has power seats, you can raise or lower the whole front seat, move the seat forward or backward and tilt the front or back of the seat up or down.

art:0001297-B

The seat base controls on the driver’s seat

85

File:06cdsso.ex Update:Thu Sep 12 11:03:20 1996

[SS01900(ALL)12/95]

[SS02000(O )12/95]

[SS02200(ALL)12/95]

13-1/2 pica art:0000462-E

[SS02300(ALL)12/95]

[SS02400(ALL)12/95]

% [SS02500(ALL)12/95]

[SS02600(ALL)12/95]

To move the seat forward or back, slide the seat base control button forward or back. To raise or lower the height of the seat base, slide the button up or down. To raise or lower the front of the seat base, slide the front of the button up or down. To raise or lower the rear of the seat base, slide the back of the button up or down. Power seatback (if equipped)

The seatback controls on the driver’s seat To tilt the seatback forward or back, slide the top part of the top button forward or back. To inflate or deflate the lumbar support pads, slide the bottom of the button forward or back. Folding Rear Seats (If equipped) The release knobs for the split rear folding seatbacks are in the trunk. Pull the knob to fold down the seat. To raise the rear seatback, push the seatback upward until it locks in place. Make sure it is firmly latched by pushing forward and back on it.

86

File:06cdsso.ex Update:Thu Sep 12 11:03:20 1996

*[SS02700(ALL)02/96]

[SS02800(ALL)12/95]

10-1/2 pica

art:0001248-B

[SS02810(ALL)01/96] %*[SS02900(ALL)02/96] *[SS03000(ALL)02/96]

*[SS03100(ALL)02/96] *[SS03200(ALL)02/96] *[SS03300(ALL)02/96] *[SS03400(ALL)02/96] *[SS03500(ALL)02/96] *[SS03600(ALL)02/96]

Seating and Safety Restraints

(cid:82)WARNING

Check to see that the seat and seatback are latched securely in position. Keep floor area free of objects that would prevent proper seat engagement. Never attempt to adjust the seat while the vehicle is in motion.

Folding rear seatback release knob

n a small storage pocket on the outside of the front seat base Important Safety Belt Information The use of safety belts helps to restrain you and your passengers in case of a collision. In most states and in Canada the law requires their use. Safety belts provide best restraint when: n the seatback is upright n the occupant is sitting upright (not slouched) n the lap belt is snug and low on the hips n the shoulder belt is snug against the chest n the knees are straight forward

87

File:06cdsso.ex Update:Thu Sep 12 11:03:20 1996

*[SS03700(ALL)02/96]

*[SS03800(ALL)02/96]

*[SS03900(ALL)02/96]

*[SS04000(ALL)02/96]

*[SS04100(ALL)02/96]

*[SS04200(ALL)02/96]

To help you remember to fasten your safety belt, a warning light may come on and a chime may sound. See Safety Belt Warning Light and Chime in the Instrumentation chapter. See the following sections in this chapter for directions on how to properly use these safety belts. Also see Safety Restraints for Children in this chapter for special instructions about using safety belts for children.

(cid:82)WARNING

Always drive and ride with your seatback upright and the lap belt snug and low across the hips.

(cid:82)WARNING

Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that are designed to be used as a pair. 1) Use the shoulder belt on the outside shoulder only. Never wear the shoulder belt under the arm. 2) Never swing it around your neck over the inside shoulder. 3) Never use a single belt for more than one person.

(cid:82)WARNING

Ford recommends that all safety belt assemblies and attaching hardware should be inspected by a qualified technician after any collision. Safety belt assemblies not in use during a collision should also be inspected and replaced if either damage or improper operation is noted.

(cid:82)WARNING

Children should always ride with the seatback in the fully upright position.

88

File:06cdsso.ex Update:Thu Sep 12 11:03:20 1996

*[SS04300(ALL)02/96]

*[SS04400(ALL)02/96]

%*[SS04500(ALL)02/96] *[SS04600(ALL)02/96]

*[SS04700(ALL)01/96] *[SS04800(ALL)02/96]

Seating and Safety Restraints

(cid:82)WARNING

Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision.

(cid:82)WARNING

Lock the doors of your vehicle before driving to lessen the risk of the door coming open in a collision.

Combination Lap and Shoulder Belts While your vehicle is in motion, the combination lap and shoulder belt adjusts to your movement. However, if you brake hard, turn hard, or if your vehicle receives an impact of 5 mph (8 km/h) or more, the lap/shoulder belt locks and helps reduce your forward movement. After you get into your vehicle, close the door and lock it. Then adjust the seat to the position that suits you best. Pull the combination lap/shoulder belt from the retractor so that the shoulder portion of the belt crosses your shoulder and chest. Be sure the belt is not twisted. If it is, remove the twist. Insert the belt tongue into the proper buckle until you hear a snap and feel it latch. Make sure the tongue is securely fastened to the buckle by pulling on tongue.

89

File:06cdsso.ex Update:Thu Sep 12 11:03:20 1996

[SS04900(ALL)12/95]

10-1/2 pica

art:0001196-A *[SS05000(ALL)02/96] %*[SS05100(ALL)12/95]

[SS05200(ALL)12/95]

10-1/2 pica art:0000684-E

Fastening the front seat lap and shoulder belt

NOTE: Be sure to read and understand Important Safety Belt

Information in this chapter.

To adjust the lap part of the belt, pull up on the shoulder belt until the lap belt fits snugly and as low as possible around your hips.

*[SS05300(ALL)02/96]

Unfastening the combination lap and shoulder belts While the belt retracts, guide the tongue to its original position to prevent it from striking you or the vehicle.

90

File:06cdsso.ex Update:Thu Sep 12 11:03:20 1996

% [SS05400(ALL)12/95]

[SS05500(ALL)12/95]

*[SS05600(ALL)02/96] [SS05700(ALL)12/95]

%*[SS05800(ALL)02/96] *[SS05900(ALL)12/95]

*[SS06000(ALL)03/96]

*[SS06100(ALL)02/96] *[SS06200(ALL)12/95]

*[SS06300(ALL)12/95]

Seating and Safety Restraints

Dual Locking Mode Lap/Shoulder Belt Retractor The front passenger seat and the rear outer seat combination lap and shoulder belts are equipped with a dual locking mode retractor on the shoulder belt portion of the lap/shoulder belt. This retractor can be switched from vehicle sensitive (emergency) locking mode to automatic locking mode by pulling the belt webbing all of the way out of the retractor. The retractor modes function as follows. Vehicle sensitive (emergency) locking mode In this operating mode, the lap/shoulder belt retractor will allow the occupant freedom of movement, locking tight only on hard braking, hard cornering or impacts of approximately 5 mph (8 km/h) or more. Automatic locking mode This mode must be used when installing a child seat on the front passenger seat and rear seats where dual locking retractors are provided. To switch the retractor from the emergency locking mode to the automatic locking mode, perform the following steps:

(cid:82)WARNING

Rear-facing child seats or infant carriers should never be placed in the front seats.

1. Buckle the lap/shoulder combination belt. 2. Grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. At this time, the retractor is in the automatic locking mode (child restraint mode).

3. Allow the belt to retract. A clicking sound will be heard as

the belt retracts. This indicates that the retractor is in the automatic locking mode.

91

File:06cdsso.ex Update:Thu Sep 12 11:03:20 1996

[SS06400(ALL)12/95] *[SS06500(ALL)02/96]

%*[SS06600(ALL)01/96] *[SS06700(ALL)01/96] [SS06800(ALL)12/95]

*[SS06900(ALL)12/95]

[SS07000(ALL)12/95]

17-1/2 pica

4. Pull up on the shoulder belt to remove slack in the lap belt. NOTE: When the combination lap/shoulder belt is unbuckled

and allowed to retract completely, the retractor will switch to the vehicle sensitive (emergency) locking mode. See the detailed instructions under Safety Seats for Children in this chapter.

Shoulder Belt Height Adjustment Driver and right front passenger You can adjust the shoulder belt height to one of four (4) positions. To adjust the belt down, push the release button (see figures 1
and 2). To adjust the belt up, slide the adjuster up. (You do not have to push the release button.)

art:0001183-C

Figure 1 — The shoulder belt height adjuster