Download PDF Manual

portant to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst damage. NOTE: systems can result against you. In unusual situations involving grossly malfunctioning engine operation, a scorching odor may suggest severe and abnormal catalyst overheating. If this occurs, stop the vehicle, turn off the engine and allow it to cool. Service, including a tune-up to manufacturer’s specifica- tions, should be obtained immediately.


Intentional tampering with emissions control in civil penalties being assessed


To minimize the possibility of catalytic converter dam- age: • Do not shut off the engine or interrupt the ignition, when the transmission is in gear and the vehicle is in motion. • Do not try to start the engine by pushing or towing the • Do not idle the engine with any spark plug wires disconnected or removed, such as when diagnostic testing, or for prolonged periods during very rough idle or malfunctioning operating conditions.


vehicle.


Cooling System


WARNING!


• When working near the radiator cooling fan, dis- connect the fan motor lead or turn the ignition switch to the LOCK position. The fan is tempera- ture controlled and can start at anytime the igni- tion switch is in the ON position. • You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator. If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the radiator is hot.


Coolant Checks Check engine coolant (antifreeze) protection every 12 months (before the onset of freezing weather, where applicable). If the engine coolant (antifreeze) is dirty or


MAINTAINING YOUR VEHICLE 369
rusty in appearance, the system should be drained, flushed, and refilled with fresh engine coolant (anti- freeze). Check the front of the A/C condenser for any accumulation of bugs, leaves, etc. If dirty, clean by gently spraying water from a garden hose vertically down the face of the condenser. Check the coolant recovery bottle tubing for brittle rub- ber, cracking, tears, cuts, and tightness of the connection at the bottle and radiator. Inspect the entire system for leaks. Cooling System – Drain, Flush, and Refill If the engine coolant (antifreeze) is dirty or contains a considerable amount of sediment, clean and flush with a reliable cooling system cleaner. Follow with a thorough rinsing to remove all deposits and chemicals. Properly dispose of the old engine coolant (antifreeze). Refer to “Maintenance Schedule” for further information.


370 MAINTAINING YOUR VEHICLE Selection Of Coolant Use only the manufacturer’s recommended coolant. Re- fer to “Fluids, Lubricants, and Genuine Parts” in “Main- taining Your Vehicle” for further information.


CAUTION!


• Mixing of engine coolant (antifreeze) other than specified HOAT engine coolant (antifreeze), may result in engine damage and may decrease corro- sion protection. If a non-HOAT engine coolant (antifreeze) is introduced into the cooling system in an emergency, it should be replaced with the specified engine coolant (antifreeze) as soon as possible.


(Continued)


CAUTION! (Continued)


• Do not use water alone or alcohol-based engine coolant (antifreeze) products. Do not use addi- tional rust inhibitors or antirust products, as they may not be compatible with the engine coolant (antifreeze) and may plug the radiator. • This vehicle has not been designed for use with Propylene Glycol based engine coolant (anti- freeze). Use of Propylene Glycol based engine coolant (antifreeze) is not recommended.


Adding Coolant Your vehicle has been built with an improved engine coolant (antifreeze) that allows extended maintenance intervals. This engine coolant (antifreeze) can be used up to five years or 102,000 miles (170 000 km) before


replacement. To prevent reducing this extended mainte- nance period, it is important that you use the same engine coolant (antifreeze) throughout the life of your vehicle. Please review these recommendations for using Hybrid Organic Additive Technology (HOAT) engine coolant (antifreeze). When adding engine coolant (antifreeze): • The manufacturer


recommends using MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) or equivalent. • Mix a minimum solution of 50% HOAT engine coolant and distilled water. Use higher concentrations (not to exceed 70%) if temperatures below ⫺34°F (⫺37°C) are anticipated. • Use only high purity water such as distilled or deion- ized water when mixing the water/engine coolant


MAINTAINING YOUR VEHICLE 371
(antifreeze) solution. The use of lower quality water will reduce the amount of corrosion protection in the engine cooling system.


Please note that it is the owner’s responsibility to main- tain the proper level of protection against freezing ac- cording to the temperatures occurring in the area where the vehicle is operated. NOTE: Mixing engine coolant (antifreeze) types will decrease the life of the engine coolant (antifreeze) and will require more frequent coolant changes. Cooling System Pressure Cap The cap must be fully tightened to prevent loss of engine coolant (antifreeze), and to ensure that engine coolant (antifreeze) will return to the radiator from the coolant recovery bottle. The cap should be inspected and cleaned if there is any accumulation of foreign material on the sealing surfaces.


372 MAINTAINING YOUR VEHICLE


WARNING!


• The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety pre- caution. Never add engine coolant (antifreeze) when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure. • Do not use a pressure cap other than the one specified for your vehicle. Personal injury or en- gine damage may result.


Disposal of Used Engine Coolant Used ethylene glycol based engine coolant (antifreeze) is a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal


rules for your community. To prevent ingestion by ani- mals or children, do not store ethylene glycol based engine coolant (antifreeze) in open containers or allow it to remain in puddles on the ground. If ingested by a child or pet, seek emergency assistance immediately. Clean up any ground spills immediately. Coolant Level 4 Cylinder Engines — the coolant bottle provides a quick visual method for determining that the engine coolant (antifreeze) level is adequate. With the engine idling and warm to normal operating temperature, the level of the engine coolant (antifreeze) in the bottle should be be- tween the “ADD” and “FULL” lines, shown on the bottle. 6 Cylinder Engines — the level of the engine coolant (antifreeze) in the pressurized coolant bottle should be between the “COLD” and “FULL” range on the bottle when the engine is cold.


The radiator normally remains completely full, so there is no need to remove the radiator cap unless checking for engine coolant (antifreeze) freeze point or replacing cool- ant. Advise your service attendant of this. As long as the engine operating temperature is satisfactory, the coolant bottle need only be checked once a month. When addi- tional engine coolant (antifreeze) is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill. Points To Remember NOTE: When the vehicle is stopped after a few miles (kilometers) of operation, you may observe vapor coming from the front of the engine compartment. This is nor- mally a result of moisture from rain, snow, or high humidity accumulating on the radiator and being vapor- ized when the thermostat opens, allowing hot engine coolant (antifreeze) to enter the radiator.


MAINTAINING YOUR VEHICLE 373
If an examination of your engine compartment shows no evidence of radiator or hose leaks, the vehicle may be safely driven. The vapor will soon dissipate. • Do not overfill the coolant recovery bottle. • Check engine coolant (antifreeze) freeze point in the radiator and in the coolant recovery bottle. If engine coolant (antifreeze) needs to be added, contents of coolant recovery bottle must also be protected against freezing. • If frequent engine coolant (antifreeze) additions are required, or if the level in the coolant recovery bottle does not drop when the engine cools, the cooling system should be pressure tested for leaks. • Maintain engine coolant (antifreeze) concentration at 50% HOAT engine coolant (antifreeze) (minimum) and distilled water for proper corrosion protection of your engine, which contains aluminum components.


374 MAINTAINING YOUR VEHICLE


• Make sure that the radiator and coolant recovery bottle overflow hoses are not kinked or obstructed. • Keep the front of the radiator clean. If your vehicle is equipped with air conditioning, keep the front of the condenser clean. • Do not change the thermostat for Summer or Winter operation. If replacement is ever necessary, install ONLY the correct type thermostat. Other designs may result in unsatisfactory cooling performance, poor gas mileage, and increased emissions.


Brake System In order to assure brake system performance, all brake system components should be inspected periodically. Refer to “Maintenance Schedule” for further information.


WARNING!


Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage. You would not have your full braking capacity in an emergency.


Master Cylinder – Brake Fluid Level Check Check the fluid level in the master cylinder immediately if the brake system warning light indicates system fail- ure. Check the fluid level in the master cylinder when per- forming underhood services.


Clean the top of the master cylinder area before removing the cap. If necessary, add fluid to bring the fluid level up to the requirements described on the brake fluid reser- voir. Overfilling of fluid is not recommended because it may cause leaking in the system. Fluid level can be expected to fall as the brake pads wear. Brake fluid level should be checked when pads are replaced. However, low fluid level may be caused by a leak and a checkup may be needed. Use only manufacturer’s recommended brake fluid. Re- fer to “Fluids, Lubricants, and Genuine Parts” in “Main- taining Your Vehicle” for further information.


MAINTAINING YOUR VEHICLE 375


WARNING!


• Use only manufacturer’s recommended brake fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information. Using the wrong type of brake fluid can severely damage your brake system and/or impair its performance. The proper type of brake fluid for your vehicle is also labeled on the origi- nal factory installed hydraulic master cylinder reservoir.


(Continued)


376 MAINTAINING YOUR VEHICLE


WARNING! (Continued)


• To avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container. Keep the master cylinder reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lower boiling point. This may cause it to boil unexpectedly during hard or prolonged braking, resulting in sudden brake failure. This could result in a accident. • Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts, causing the brake fluid to catch fire. Brake fluid can also damage painted and vinyl surfaces, care should be taken to avoid its contact with these surfaces.


(Continued)


WARNING! (Continued)


• Do not allow petroleum based fluid to contami- nate the brake fluid. Brake seal components could be damaged, causing partial or complete brake failure. This could result in an accident.


Automatic Transmission The automatic transmission and differential assembly are contained within a single housing. The fluid level in the automatic transmission should be checked whenever the vehicle is serviced. Operation with an improper fluid level will greatly reduce the life of the transmission and the fluid.


Fluid Level Check – 2.4L and 2.7L Engines Use the following procedure to check the automatic transmission fluid level properly: 1. Park the vehicle on level ground. 2. Run the engine at curb idle speed for a minimum of 60 seconds. 3. Apply the parking brake fully. 4. Place the shift lever momentarily into each gear posi- tion ending with the lever in PARK. 5. Wipe the area around the dipstick clean to eliminate the possibility of dirt entering the transmission. 6. Remove the dipstick and determine if the fluid is hot or cold. Hot fluid is approximately 180°F (82° C), which is the normal operating temperature after the vehicle is


MAINTAINING YOUR VEHICLE 377
driven at least 15 miles (24 km). Hot fluid cannot be held comfortably between the fingertips. Cold fluid is at a temperature below 80°F (27° C). 7. Wipe the dipstick clean and reinsert until seated. Then, remove dipstick and note the reading.


a. If the fluid is hot, the reading should be in the crosshatched area marked “HOT” (between the upper two holes in the dipstick). b. If the fluid is cold, the fluid level should be between the lower two holes in the area marked “COLD.”


If the fluid level is low, add sufficient fluid through the filler (dipstick) tube to bring it to the proper level. Do not overfill.


378 MAINTAINING YOUR VEHICLE


CAUTION!


• Using a transmission fluid other than the manu- facturer’s recommended fluid may cause deterio- ration in transmission shift quality and/or torque converter shudder. Using a transmission fluid other than that recommended by the manufacturer will result in more frequent fluid and filter changes. Refer to “Fluids, Lubricants, and Genu- ine Parts” in “Maintaining Your Vehicle” for fur- ther information. • Dirt and water in the transmission can cause serious damage. To prevent dirt and water from entering the transmission after checking or replen- ishing fluid, make certain that the dipstick cap is re-seated properly.


Fluid Level Check – 3.5L Engine The automatic transmission has no dipstick and is dealer serviced only. Transmission Fluid and Filter Changes Refer to “Maintenance Schedule” for further information. In addition, change the fluid and filter if the transmission is disassembled for any reason. Special Additives Automatic Transmission Fluid (ATF) is an engineered product and its performance may be impaired by supple- mental additives. Therefore, do not add any fluid addi- tives to the transmission. The only exception to this policy is the use of special dyes to aid in detecting fluid leaks. In addition, avoid using transmission sealers as they may adversely affect seals.


CAUTION!


Do not use chemical flushes in your transmission as the chemicals can damage your transmission compo- nents. Such damage is not covered by the New Vehicle Limited Warranty.


Appearance Care and Protection from Corrosion


Protection of Body and Paint from Corrosion Vehicle body care requirements vary according to geo- graphic locations and usage. Chemicals that make roads passable in snow and ice and those that are sprayed on trees and road surfaces during other seasons are highly corrosive to the metal in your vehicle. Outside parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather and other extreme conditions will have an adverse effect on paint, metal trim, and under- body protection.


MAINTAINING YOUR VEHICLE 379
The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle. What Causes Corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle. The most common causes are: • Road salt, dirt, and moisture accumulation. • Stone and gravel impact. • Insects, tree sap, and tar. • Salt in the air near seacoast localities. • Atmospheric fallout/industrial pollutants.


380 MAINTAINING YOUR VEHICLE Washing • Wash your vehicle regularly. Always wash your ve- hicle in the shade using MOPAR威 Car Wash or equiva- lent, or a mild car wash soap, and rinse the panels completely with clear water. • If insects, tar, or other similar deposits have accumu- lated on your vehicle, use MOPAR威 Super Kleen Bug and Tar Remover or equivalent to remove. • Use a high quality cleaner wax, such as MOPAR威 Cleaner Wax or equivalent to remove road film, stains and to protect your paint finish. Take care never to scratch the paint. • Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.


CAUTION!


• Do not use abrasive or strong cleaning materials such as steel wool or scouring powder, which will scratch metal and painted surfaces. • Use of power washers exceeding 1,200 psi (8 274 kPa) can result in damage or removal of paint and decals.


Special Care • If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month. • It is important that the drain holes in the lower edges of the doors, rocker panels, and trunk be kept clear and open.


• If you detect any stone chips or scratches in the paint, touch them up immediately. The cost of such repairs is considered the responsibility of the owner. • If your vehicle is damaged due to an accident or similar cause which destroys the paint and protective coating, have your vehicle repaired as soon as pos- sible. The cost of such repairs is considered the respon- sibility of the owner. • If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed. • If a lot of driving is done on gravel roads, consider • Use MOPAR威 Touch Up Paint or equivalent on scratches as soon as possible. Your authorized dealer has touch up paint to match the color of your vehicle.


mud or stone shields behind each wheel.


MAINTAINING YOUR VEHICLE 381


Wheel and Wheel Trim Care All wheels and wheel trim, especially aluminum and chrome-plated wheels, should be cleaned regularly with a mild soap and water to prevent corrosion. To remove heavy soil and/or excessive brake dust, use MOPAR威 Wheel Cleaner or equivalent or select a nonabrasive, non-acidic cleaner. Do not use scouring pads, steel wool, a bristle brush, or metal polishes. Only MOPAR威 or equivalent is recommended. Do not use oven cleaner. Avoid automatic car washes that use acidic solutions or harsh brushes that may damage the wheels’ protective finish. Cleaning Headlights Your vehicle has plastic headlights that are lighter and less susceptible to stone breakage than glass headlights. Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed.


382 MAINTAINING YOUR VEHICLE To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution fol- lowed by rinsing. Do not use abrasive cleaning components, solvents, steel wool or other aggressive material to clean the lenses. Stain Repel Fabric Cleaning Procedure – If Equipped Stain Repel seats may be cleaned in the following man- ner: • Remove as much of the stain as possible by blotting • Blot any remaining stain with a clean, damp towel. • For tough stains, apply MOPAR威 Total Clean or equivalent, or a mild soap solution to a clean, damp cloth and remove the stain. Use a fresh, damp towel to remove soap residue.


with a clean, dry towel.


• For grease stains, apply MOPAR威 Multi-Purpose Cleaner or equivalent to a clean, damp cloth and remove the stain. Use a fresh, damp towel to remove soap residue. • Do not use any harsh solvents or any other form of


protectants on Stain Repel products.


Interior Care


Instrument Panel Cover The instrument panel cover has a low glare surface, which minimizes reflections in the windshield. Do not use protectants or other products, which may cause undesirable reflections. Use soap and warm water to restore the low glare surface. Cleaning Interior Trim Interior trim should be cleaned starting with a damp cloth, a damp cloth with MOPAR威 Total Clean or equiva- lent, then MOPAR威 Spot & Stain Remover or equivalent


if absolutely necessary. Do not use harsh cleaners or Armor All威. Use MOPAR威 Total Clean or equivalent to clean vinyl upholstery. Cleaning Leather Upholstery MOPAR威 Total Clean or equivalent is specifically recom- mended for leather upholstery. Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather upholstery and should be removed promptly with a damp cloth. Stubborn soils can be removed easily with a soft cloth and MOPAR威 Total Clean or equivalent. Care should be taken to avoid soaking your leather upholstery with any liquid. Please do not use polishes, oils, cleaning fluids, solvents, detergents, or ammonia-based cleaners to clean your leather upholstery. Application of a leather condi- tioner is not required to maintain the original condition.


MAINTAINING YOUR VEHICLE 383


WARNING!


Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed areas they may cause respiratory harm.


Glass Surfaces All glass surfaces should be cleaned on a regular basis with MOPAR威 Glass Cleaner or any commercial household-type glass cleaner. Never use an abrasive type cleaner. Use caution when cleaning the inside rear win- dow equipped with electric defrosters or the right rear quarter window equipped with the radio antenna. Do not use scrapers or other sharp instruments, which may scratch the elements. When cleaning the rear view mirror, spray cleaner on the towel or rag that you are using. Do not spray cleaner directly on the mirror.


384 MAINTAINING YOUR VEHICLE Cleaning Plastic Instrument Cluster Lenses The lenses in front of the instruments in this vehicle are molded in clear plastic. When cleaning the lenses, care must be taken to avoid scratching the plastic. 1. Clean with a wet, soft rag. A mild soap solution may be used, but do not use high alcohol content or abrasive cleaners. If soap is used, wipe clean with a clean damp rag. 2. Dry with a soft tissue. Seat Belt Maintenance Do not bleach, dye, or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage can also weaken the fabric. If the belts need cleaning, use a mild soap solution or lukewarm water. Do not remove the belts from the car to wash them.


Replace the belts if they appear frayed or worn or if the buckles do not work properly. Dry with a soft tissue. Cleaning Center Console Cupholders


the cupholder and lift


Removal Grab the rubber portion of upward. Cleaning Soak the rubber cupholder liner in a mixture of medium hot tap water and one teaspoon of mild liquid dish soap. Let soak for approximately one hour. After one hour pull the liner from the water and dip it back into the water about six times. This will loosen any remaining debris. Rinse the liner thoroughly under warm running water. Shake the excess water from the liner and dry the outer surfaces with a clean soft cloth.


Installation Align the liner in the cupholder and press down firmly. Convertible Top Care


CAUTION!


Failure to follow these cautions may cause interior water damage, stains or mildew on the top material: • Avoid high-pressure car washes, as they can dam- age the top material. Also, increased water pres- sure may force past the weather strips. • Remove any standing water from the top and dry the surface before opening it. Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicles interior.


(Continued)


MAINTAINING YOUR VEHICLE 385


CAUTION! (Continued)


• Use care when washing the vehicle, water pressure directed at the weather strip seals may cause water to leak into the vehicles interior.


Immediate removal of any contaminant is recommended. Regular washing of the top will enhance its life and appearance, and make successive cleanings easier. Do not subject the top to excessive heat. Frequently vacuum the top and storage compartment.


386 MAINTAINING YOUR VEHICLE Washing Hand washing is highly recommended. Automatic car washing equipment can damage the top material. If you must use an automatic car wash, soft cloth systems are preferred.


CAUTION!


Avoid high-pressure car washes, as they can damage the top material. Also, increased water pressure may force water past the weather strips.


General Cleaning Careful vacuuming of the top before washing is helpful in removing dust and other foreign particles. Wash in partial shade instead of direct sun. Wet the entire vehicle before washing the top. The top should be washed with a soft, natural bristle scrub brush, and a mild soap solution such as liquid dishwashing soap. Do not use detergent.


CAUTION!


Never use an abrasive type cleaner or bleaches. Cleaners should not contain silicones, organic sol- vents, petroleum distillates, or plasticizers. Always wait until the top is thoroughly dry before lowering it into the storage area.


Scrub in all directions, covering an area of about two square feet at a time. Avoid heavy scrubbing. Rinse the entire vehicle with water to remove all soap and dirt from the top fabric and to prevent streaking on painted and chrome surfaces. Allow the top to dry before lowering. Vacuuming the top with a wet/dry shop vacuum will decrease the top’s drying time, ensure removal of all dirt, and delete streaks in the material. Multiple cleanings may be necessary to remove stubborn stains. If stains persist, further suggestions.


local dealership for


contact your


Additional Cleaning Procedure For additional cleaning assistance in removing stubborn stains, apply MOPAR威 Convertible Cloth Top Cleaner or equivalent to the complete stain, extending 2 inches (50 mm) beyond the stain. With a soft bristle brush, scrub in all directions over the stain. Avoid heavy scrubbing. Rinse the area with warm water. If the stain is still apparent, repeat the cleaning procedure. When the stain is no longer showing, rinse the complete top with warm water. Let the top dry before lowering it. Protection For appearance purposes, you may wish to protect your cloth top periodically. A fabric protectant such as Scotch- guard威 is suggested. The top should be clean and dry before application of the protectant.


MAINTAINING YOUR VEHICLE 387


CAUTION!


Avoid getting Scotchguard威 on the surrounding weather strips, moldings, paint, or glass. Damage to these items might occur.


Weather Strip Care – Soft and Hard Top Lubricate all top and door glass weather strips periodi- cally with MOPAR威 Weather Strip Lubricant or equiva- lent to keep them soft and pliable.


388 MAINTAINING YOUR VEHICLE FUSES


Totally Integrated Power Module (TIPM) The TIPM is located in the engine compartment near the air cleaner assembly. This center contains cartridge fuses and mini fuses. A label that identifies each component may be printed on the inside of the cover. Refer to the graphic below for FUSES/TIPM location.


Totally Integrated Power Module (TIPM)


Cavity


Cartridge


Fuse


40 Amp Green







Mini Fuse



20 Amp Yellow


10 Amp


Red


10 Amp


Red


20 Amp Yellow


10 Amp


Red


Description


Cavity


Power Top Mod- ule – If Equipped


AWD Module


Battery Feed – Center High Mounted Stop Light (CHMSL)/ Brake Switch Battery Feed – Ignition Switch Trailer Tow – If Equipped Ignition Off Draw (IOD) – Power Mirror Switch/ Climate Controls


10


11


12


MAINTAINING YOUR VEHICLE 389


Cartridge


Fuse




40 Amp Green





Mini Fuse


30 Amp Green 30 Amp Green


20 Amp Yellow


15 Amp Lt Blue 20 Amp Yellow


Description


Ignition Off Draw (IOD) Sense 1
Ignition Off Draw (IOD) Sense 2
Battery Feed – Power Seats – If Equipped/PZEV Air Pump – If Equipped Battery Feed – Cabin Compart- ment Node (CCN) Selectable Power Outlet



390 MAINTAINING YOUR VEHICLE


Cavity


Cartridge


Fuse


Mini Fuse


20 Amp Yellow


10 Amp


Red




40 Amp Green




15 Amp Lt. Blue


13


14


15


16


Description


Cavity


Cartridge


Fuse


Mini Fuse



Ignition Off Draw (IOD) – Cabin Compartment Node (CCN)/ Interior Lighting Battery Feed – Ra- diator Fan Relay IGN Run/ACC – Cigar Lighter/ PWR Sunroof Mod


17


18


19


20


21



10 Amp


Red


40 Amp Green






20 Amp Yellow


15 Amp Lt. Blue 10 Amp


Red


Description


Ignition Off Draw (IOD) – Wireless Control Module (WCM)/Clock/ Steering Control Module (SCM) Battery Feed – Auto Shutdown (ASD) Relay Ignition Off Draw (IOD) – Power Amp Feed 2 – If Equipped Ignition Off Draw (IOD) – Radio



MAINTAINING YOUR VEHICLE 391


Cavity


Cartridge


Fuse


Mini Fuse


Description


Cavity


Cartridge


Fuse


Mini Fuse


22


23


24


25


26







10 Amp


Red


15 Amp Lt. Blue


25 Amp Natural


10 Amp


Red


15 Amp Lt. Blue


Ignition Run – Climate Controls/ Hot Cupholder – If Equipped Auto Shutdown (ASD) Relay Feed Battery Feed — PWR Sunroof Feed Ignition Run — Heated Mirrors - If Equipped Auto Shutdown (ASD) Relay Feed


27


28


29


30






10 Amp


Red


10 Amp


Red



20 Amp Yellow


Description


Ignition Run – Occupant Classifi- cation Module (OCM)/Occupant Restraint Control- ler (ORC) Ignition Run — Occupant Classifi- cation Module (OCM)/Occupant Restraint Control- ler (ORC) Hot Car (No Fuse Required) Ignition Run – Heated Seats – If Equipped


392 MAINTAINING YOUR VEHICLE


Cavity


31


32


33


Cartridge


Fuse



30 Amp


Pink


Mini Fuse


10 Amp


Red




10 Amp


Red


Description


Cavity


Cartridge


Fuse


Mini Fuse



Auto Shutdown (ASD) Relay Feed Battery Feed – Switch Bank/ Diagnostic Link Connector/ Powertrain Con- trol Module (PCM)


34


35


30 Amp


Pink


40 Amp Green




Description


Battery Feed – Anti-Lock Brakes (ABS) Module – If Equipped/ Electronic Stability Control (ESC) Module – If Equipped Battery Feed – Anti-Lock Brakes (ABS) Module – If Equipped/ Electronic Stability Control (ESC) Module – If Equipped


Cavity


Cartridge


Fuse


Mini Fuse


36


37


30 Amp


Pink




25 Amp Natural


Description


Battery Feed – Passenger Door Module (PDM)/ Driver Door Mod- ule (DDM) Power Top Mod- ule – If Equipped


CAUTION!


• When installing the Totally Integrated Power Module cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the Totally Integrated Power Module, and possibly result in an electrical system failure.


(Continued)


MAINTAINING YOUR VEHICLE 393


CAUTION! (Continued)


• When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system over- load. If a properly rated fuse continues to blow, it indicates a problem in the circuit that must be corrected.


VEHICLE STORAGE If you will not be using your vehicle for more than 21 days, you may want to take steps to preserve your battery. • Disengage the mini-fuse in the Power Distribution • Disconnect the negative cable from the battery.


Center labeled IOD (Ignition Off-Draw).


394 MAINTAINING YOUR VEHICLE REPLACEMENT BULBS All the inside bulbs are brass or glass wedge base. Aluminum base bulbs are not approved and should not be used for replacement.


LIGHT BULBS – Interior Bulb Number Front Courtesy/Reading Lamps . . LED (Dealer Service) Center Console Courtesy Lamp . . . . . . . . . . 578/W5W Glove Box Lamp . . . . . . . . . . . . . . . . . . . . . . . . . 194
Rear Compartment (Trunk) Lamp . . . . . . . . . . . . . 579
NOTE: For lighted switches, see your dealer for replace- ment instructions.


LIGHT BULBS – Exterior Bulb No. Low Beam Headlamp. . . . . . . . . . . . . . . . . . . . . 9006
High Beam Headlamp . . . . . . . . . . . . . . . . . . . . 9005
Front Park/Turn Signal/Side Marker Lamp . . . 3457AK Front Fog Lamp . . . . . . . . . . . . . . . . . . . . . . PSX24W


Center High Mounted Stop Lamp (CHMSL) . . . . . . . . . . . . . . . . . . . . . . . . W16W (921) Rear Tail/Stop Lamp . . . . . . . . . . . . . . . . . . . . . 3057
Rear Turn Signal Lamp. . . . . . . . . . . . . . . . . . . . 3057
Backup Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . 3157
License Lamp . . . . . . . . . . . . . . . . . . . . . 168 or W5W


BULB REPLACEMENT


Headlamp


1. Raise and prop open the hood. Locate the connector behind the headlamp. It may be necessary to remove the air cleaner NOTE: filter housing and position the totally integrated power module aside prior to replacing the low beam headlamp on the driver’s side of the vehicle.


2. Reach into engine compartment and from behind the lamp assembly and grasp the connector.


MAINTAINING YOUR VEHICLE 395
3. Rotate bulb and connector one-quarter turn and pull outward from assembly.


CAUTION!


Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life.


396 MAINTAINING YOUR VEHICLE 4. Pull the bulb out of the socket and replace the bulb.


Front Turn Signal/Parking Lamp


1. Raise and prop open the hood. 2. Rotate the bulb’s electrical connector one-quarter turn counterclockwise and remove it from the headlamp housing.


5. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. 6. Reinsert the bulb and socket assembly and rotate clockwise one-quarter turn to secure.


3. Remove the bulb from the connector socket and install the replacement bulb. 4. Install the bulb and connector assembly into the headlamp housing and rotate the connector one-quarter turn clockwise to lock it in place. Front Fog Lamp


NOTE: Access to the lamps through the lower fascia cutout is limited. We recommend you access the lamps by turning the steering wheel to allow access and remove the inner fender shield. 1. Rotate the bulb’s electrical connector one-quarter turn counterclockwise and remove it from the fog lamp hous- ing.


MAINTAINING YOUR VEHICLE 397


2. Remove the bulb from the connector socket and install the replacement bulb.


398 MAINTAINING YOUR VEHICLE


CAUTION!


Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with an oily surface, clean the bulb with rubbing alcohol.


3. Install the bulb and connector assembly into the fog lamp housing and rotate the connector one-quarter turn clockwise to lock it in place. Tail/Stop, Rear Turn Signal and Backup Lamps The taillamps are a two piece design. The turn signal, brake and taillamps are located in the rear corner body panel housing. The backup and taillamps are located in the trunk lid housing.


Changing the Tail/Stop Lamp or Rear Turn Signal Lamp 1. Open the trunk and gently pull back the trunk liner behind the taillamp


MAINTAINING YOUR VEHICLE 399


3. Grasp the taillamp housing and pull it firmly outward while pushing gently on the studs from inside to disen- gage the housing from the vehicle.


2. Remove the two plastic wing nuts from the taillamp housing.


400 MAINTAINING YOUR VEHICLE 4. Rotate the applicable bulb’s electrical connector one- quarter turn counterclockwise and remove it from the taillamp housing.


5. Remove the bulb from the connector socket and install the replacement bulb. 6. Install the bulb and connector assembly into the taillamp housing and rotate the connector one-quarter turn clockwise to lock it in place. 7. Reinstall the taillamp housing. Changing the Backup Lamp 1. Open the trunk. 2. Rotate the bulb’s electrical connector one-quarter turn counterclockwise and remove it from the housing.


1 — Tail/Stop Lamp


2 — Turn Signal Lamp


MAINTAINING YOUR VEHICLE 401


License Plate Lamp


1. Remove two retaining screws holding the lamp lens in place.


2 — Backup Lamp


1 — Rear Fog Lamp 3. Remove the bulb from the connector socket and install the replacement bulb. the bulb and connector assembly into the 4. Install housing and rotate the connector one-quarter turn clock- wise to lock it in place.


2. Gently pry the lens loose. 3. Pull bulb from socket, replace and reattach the lamp lens with the two retaining screws.


402 MAINTAINING YOUR VEHICLE Center High-Mounted Stop Lamp (CHMSL)


1. Open the trunk lid. 2. Rotate the bulb’s electrical connector one-quarter turn counterclockwise and remove it from the CHMSL hous- ing.


3. Remove the bulb from the connector socket and install the replacement bulb. 4. Install the bulb and connector assembly into the CHMSL housing and rotate the connector one-quarter turn clockwise to lock it in place.


FLUID CAPACITIES


U.S.


Fuel (Approximate) All Engines Engine Oil with Filter 2.4L Engine (SAE 5W-20, API Certified) 2.7L Engine (SAE 5W-20, API Certified) 3.5L Engine (SAE 10W-30, API Certified) Cooling System* 2.4L Engine (MOPAR威 Antifreeze/Coolant 5
Year/100,000 Mile Formula or equivalent) 2.7L Engine (MOPAR威 Antifreeze/Coolant 5
Year/100,000 Mile Formula or equivalent) 3.5L Engine (MOPAR威 Antifreeze/Coolant 5
Year/100,000 Mile Formula or equivalent) * Includes heater and coolant recovery bottle filled to MAX level.


16.9 Gallons


4.5 Quarts 5.5 Quarts 5.5 Quarts


7.7 Quarts


9.8 Quarts


11.6 Quarts


MAINTAINING YOUR VEHICLE 403


Metric


64 Liters


4.4 Liters 5.2 Liters 5.2 Liters


7.3 Liters


9.3 Liters


11 Liters


404 MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS, AND GENUINE PARTS


Engine


Engine Coolant


Component


Engine Oil – 2.4L and 2.7L Engines


Engine Oil – 3.5L Engine


Engine Oil Filter Spark Plugs – 2.4L Engine except PZEV* Spark Plugs – 2.4L Engine with PZEV* Spark Plugs – 2.7L Engine Spark Plugs – 3.5L Engine Fuel Selection – 2.4L and 2.7L Engines Fuel Selection – 3.5L Engine * PZEV = Partial Zero Emission Vehicle


Fluid, Lubricant, or Genuine Part


MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) or equivalent. Use API Certified SAE 5W-20 Engine Oil, meeting the requirements of Chrysler Material Standard MS-6395. Refer to your engine oil filler cap for correct SAE grade. Use API Certified SAE 10W-30 Engine Oil, meeting Chrysler Mate- rial Standard MS-6395. Refer to your engine oil filler cap for correct SAE grade. MOPAR威 Engine Oil Filter or equivalent. ZFR5F-11 (Gap 0.043 in [1.11 mm]) ZFR5AP (Gap 0.031 in [0.8 mm]) TE10PMC5 (Gap 0.050 in [1.27 mm]) ZFR5LP-13G (Gap 0.050 in [1.27 mm]) 87 Octane 87 Octane Acceptable – 89 Octane Recommended


Chassis


Component


Automatic Transmission


Brake Master Cylinder


Power Steering Reservoir


MAINTAINING YOUR VEHICLE 405


Fluid, Lubricant, or Genuine Part


MOPAR威 ATF+4威 Automatic Transmission Fluid or equivalent licensed ATF+4威 product. MOPAR威 DOT 3 and SAE J1703 should be used. If DOT 3 brake fluid is not available, then DOT 4 is acceptable. Use only recommended brake fluids. MOPAR威 Power Steering Fluid +4, MOPAR威 ATF+4威 Automatic Trans- mission Fluid or equivalent licensed ATF+4威 product.


MAINTENANCE SCHEDULES


CONTENTS


䡵 Emissions Control System Maintenance . . . . . . 408
䡵 Maintenance Schedule . . . . . . . . . . . . . . . . . . 408


▫ Required Maintenance Intervals . . . . . . . . . . 410


M


408 MAINTENANCE SCHEDULES EMISSIONS CONTROL SYSTEM MAINTENANCE The Scheduled Maintenance services listed in bold type must be done at the times or mileages specified to ensure the continued proper functioning of the emissions control system. These and all other maintenance services in- cluded in this manual, should be done to provide best vehicle performance and reliability. More frequent main- tenance may be needed for vehicles in severe operating conditions, such as dusty areas and very short trip driving. Inspection and service should also be done anytime a malfunction is suspected. NOTE: Maintenance, replacement or repair of the emis- sions control devices and systems on your vehicle may be performed by any automotive repair establishment or individual using any automotive part that has been certified pursuant to U.S. EPA or in the State of Califor- nia, California Air Resources Board regulations.


Information Center


MAINTENANCE SCHEDULE The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. On Electronic Vehicle (EVIC) equipped vehicles “Oil Change Required” will be dis- played in the EVIC and a single chime will sound, indicating that an oil change is necessary. On Non-EVIC equipped vehicles “Change Oil” will flash in the instrument cluster odometer and a single chime will sound, indicating that an oil change is necessary. Based on engine operation conditions the oil change indicator message will illuminate, this means that service is required for your vehicle. Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).


NOTE: • The oil change indicator message will not monitor the time since the last oil change. Change your vehicles oil if it has been 6 months since your last oil change even if the oil change indicator message is NOT illumi- nated. • Change your engine oil more often if you drive your • Under no circumstances should oil change intervals exceed 6,000 miles (10 000 km) or six months, which- ever comes first.


vehicle off-road for an extended period of time.


Your authorized dealer will reset the oil change indicator message after completing the scheduled oil change. If a scheduled oil change is performed by someone other than your authorized dealer, the message can be reset by referring to the steps described under “Electronic Vehicle Information Center (EVIC)/Oil Change Required” in


MAINTENANCE SCHEDULES 409
“Understanding Your Instrument Panel” or under “In- strument Cluster Description/Odometer/Trip Odom- eter” in “Understanding Your Instrument Panel” for further information. At Each Stop for Fuel • Check the engine oil level about five minutes after a fully warmed engine is shut off. Checking the oil level while the vehicle is on level ground will improve the accuracy of the oil level reading. Add oil only when the level is at or below the ADD or MIN mark. • Check the windshield washer solvent and add if


required.


M


damage.


410 MAINTENANCE SCHEDULES Once a Month • Check tire pressure and look for unusual wear or • Inspect the battery and clean and tighten the terminals • Check the fluid levels of coolant reservoir, brake master cylinder, and transmission and add as needed. • Check all lights and other electrical items for correct


as required.


operation.


At Each Oil Change • Change the engine oil filter. • Inspect the brake hoses and lines.


CAUTION!


Failure to perform the required maintenance items may result in damage to the vehicle.


Required Maintenance Intervals Refer to the Maintenance Schedules on the following pages for the required maintenance intervals.


6,000 Miles (10,000 km) or 6 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil


filter.


❏ Rotate tires.


MAINTENANCE SCHEDULES 411


12,000 Miles (20,000 km) or 12 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle in dusty or off-road conditions, inspect the engine air cleaner filter, and


replace if necessary.


❏ Inspect the brake linings, and replace as necessary. ❏ Replace the air conditioning filter (if equipped). ❏ Inspect the CV joints. Perform the first inspection at 12,000 miles (20 000 km) or


12 months.


❏ Inspect the exhaust system. Perform the first inspection at 12,000 miles (20 000 km) or


12 months.


❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for


damage, wear, improper looseness or end play; replace if necessary.


Odometer Reading


Repair Order #


Date


Dealer Code


Odometer Reading


Repair Order #


Date


Dealer Code


Signature Authorized Chrysler Dealer


Signature Authorized Chrysler Dealer


M


412 MAINTENANCE SCHEDULES


18,000 Miles (30,000 km) or 18 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil


filter.


❏ Rotate tires.


24,000 Miles (40,000 km) or 24 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle in dusty or off-road conditions, inspect the engine air cleaner filter, and


replace if necessary.


❏ Inspect the brake linings, and replace as necessary. ❏ Replace the air conditioning filter (if equipped). ❏ Inspect the CV joints. ❏ Inspect the exhaust system. ❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for


damage, wear, improper looseness or end play; replace if necessary.


Odometer Reading


Repair Order #


Date


Dealer Code


Odometer Reading


Repair Order #


Date


Dealer Code


Signature Authorized Chrysler Dealer


Signature Authorized Chrysler Dealer


30,000 Miles (50,000 km) or 30 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil


filter.


❏ Rotate tires. ❏ Replace the engine air cleaner filter. ❏ Replace the spark plugs (2.4L Engine


except PZEV*).


❏ Adjust parking brake on vehicles


equipped with four wheel disc brakes.


MAINTENANCE SCHEDULES 413


36,000 Miles (60,000 km) or 36 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle in dusty or off-road conditions, inspect the engine air cleaner filter, and


replace if necessary.


❏ Inspect the brake linings, and replace as necessary. ❏ Replace the air conditioning filter (if equipped). ❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for


damage, wear, improper looseness or end play; replace if necessary.


Odometer Reading


Repair Order #


Date


Dealer Code


Odometer Reading


Repair Order #


Date


Dealer Code


Signature Authorized Chrysler Dealer


Signature Authorized Chrysler Dealer


M


414 MAINTENANCE SCHEDULES


42,000 Miles (70,000 km) or 42 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil


filter.


❏ Rotate tires.


48,000 Miles (80,000 km) or 48 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle in dusty or off-road conditions, inspect the engine air cleaner filter, and


replace if necessary.


❏ Inspect the brake linings, and replace as necessary. ❏ Replace the air conditioning filter (if equipped). ❏ Inspect the CV joints. ❏ Inspect the exhaust system. ❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for


damage, wear, improper looseness or end play; replace if necessary.


Odometer Reading


Repair Order #


Date


Dealer Code


Odometer Reading


Repair Order #


Date


Dealer Code


Signature Authorized Chrysler Dealer


Signature Authorized Chrysler Dealer


54,000 Miles (90,000 km) or 54 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil


filter.


❏ Rotate tires.


MAINTENANCE SCHEDULES 415


60,000 Miles (100,000 km) or 60 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Replace the engine air cleaner filter. ❏ Replace the spark plugs (2.4L Engine except PZEV*). ❏ Inspect the brake linings, and replace as necessary. ❏ Replace the air conditioning filter (if equipped). ❏ Change the automatic transmission fluid & filter if using your vehicle for any of the


following: police, taxi, fleet, or frequent trailer towing.


❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for


damage, wear, improper looseness or end play; replace if necessary.


❏ Adjust parking brake on vehicles equipped with four wheel disc brakes.


Odometer Reading


Repair Order #


Date


Dealer Code


Odometer Reading


Repair Order #


Date


Dealer Code


Signature Authorized Chrysler Dealer


Signature Authorized Chrysler Dealer


M


416 MAINTENANCE SCHEDULES


66,000 Miles (110,000 km) or 66 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil


filter.


❏ Rotate tires.


72,000 Miles (120,000 km) or 72 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle in dusty or off-road conditions, inspect the engine air cleaner filter, and


replace if necessary.


❏ Inspect the brake linings, and replace as necessary. ❏ Replace the air conditioning filter (if equipped). ❏ Inspect the CV joints. ❏ Inspect the exhaust system. ❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for


damage, wear, improper looseness or end play; replace if necessary.


Odometer Reading


Repair Order #


Date


Dealer Code


Odometer Reading


Repair Order #


Date


Dealer Code


Signature Authorized Chrysler Dealer


Signature Authorized Chrysler Dealer


78,000 Miles (130,000 km) or 78 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil


filter.


❏ Rotate tires.


MAINTENANCE SCHEDULES 417


84,000 Miles (140,000 km) or 84 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle in dusty or off-road conditions, inspect the engine air cleaner filter, and


replace if necessary.


❏ Inspect the brake linings, and replace as necessary. ❏ Replace the air conditioning filter (if equipped). ❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for


damage, wear, improper looseness or end play; replace if necessary.


Odometer Reading


Repair Order #


Date


Dealer Code


Odometer Reading


Repair Order #


Date


Dealer Code


Signature Authorized Chrysler Dealer


Signature Authorized Chrysler Dealer


M


418 MAINTENANCE SCHEDULES


90,000 Miles (150,000 km) or 90 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil


filter.


❏ Rotate tires. ❏ Replace the engine air cleaner filter. ❏ Replace the spark plugs (2.4L Engine


except PZEV*).


❏ Inspect and replace the PCV valve, if


necessary†.


❏ Adjust parking brake on vehicles


equipped with four wheel disc brakes.


96,000 Miles (160,000 km) or 96 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle in dusty or off-road conditions, inspect the engine air cleaner filter, and


replace if necessary.


❏ Inspect the brake linings, and replace as necessary. ❏ Replace the air conditioning filter (if equipped). ❏ Inspect the CV joints. ❏ Inspect the exhaust system. ❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for


damage, wear, improper looseness or end play; replace if necessary.


Odometer Reading


Repair Order #


Date


Dealer Code


Odometer Reading


Repair Order #


Date


Dealer Code


Signature Authorized Chrysler Dealer


Signature Authorized Chrysler Dealer


102,000 Miles (170,000 km) or 102 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil


filter.


❏ Rotate tires. ❏ Replace the spark plugs (2.4L PZEV*,


2.7L and 3.5L Engines).


❏ Replace the timing belt (3.5L Engine). ❏ Flush and replace the engine coolant. ❏ Inspect accessory drive belt, replace if


necessary.


MAINTENANCE SCHEDULES 419


108,000 Miles (180,000 km) or 108 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle in dusty or off-road conditions, inspect the engine air cleaner filter, and


replace if necessary.


❏ Inspect the brake linings, and replace as necessary. ❏ Replace the air conditioning filter (if equipped). ❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for


damage, wear, improper looseness or end play; replace if necessary.


Odometer Reading


Repair Order #


Date


Dealer Code


Odometer Reading


Repair Order #


Date


Dealer Code


Signature Authorized Chrysler Dealer


Signature Authorized Chrysler Dealer


M


420 MAINTENANCE SCHEDULES


Loading...
x