2010 Chrysler Sebring Convertible Owners Manual

Download PDF Manual
amount of cargo. 88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When operating the power convertible top, the trunk lid will pivot at the rear of the vehicle, swing open by the rear window, and then pivot backward. This allows room for the top to retract into or unfold from its stowage area in the trunk. When lowering the top, the system extends the hard tonneau cover, which stows conveniently underneath the trunk lid. The tonneau cover closes the area between the rear seats and the trunk lid to conceal the top when stowed. When raising the top, the system retracts the hard tonneau cover back into its stowage area underneath the trunk lid. To complete either operation, the trunk lid returns to its normal position and then latches. Spring-loaded flipper doors, which provide clearance for the linkage, close off notches in the quarter trim panels when the top is down. Power Convertible Top Usage Precautions NOTE: • The convertible top will not operate unless the vehicle is stationary, the cargo shield is positioned correctly, and the trunk lid is closed and latched. In addition, the system prohibits lowering the top when ambient tem- perature is at 32°F (0°C) or lower, However, the system allows you to raise the top at ambient temperatures as low as 0°F (-18°C). • Do not attempt to lower the top when frost, ice, or snow may be present, this could cause damage or prevent the top from stowing completely. • The Power Top Control Module (PTCM) monitors and controls lowering and raising of the top. A series of micro-switches verify that operations are complete before allowing the next stage of lowering or raising operation. • Opening and closing the top consecutively without the • If a fluttering noise is heard from the rear seat belts while driving with the top down, safely bring the vehicle to a stop and buckle the rear seat belts over the empty seats. This will keep tension on the seat belts and remove the fluttering condition. engine running may run the battery down. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 CAUTION! • Correctly position the cargo shield in the trunk before stowing the top. Doing so closes a switch that allows top operation (stowing) to proceed. If the switch is not closed, a warning message dis- plays in the instrument cluster to notify the driver. • Always place items carefully into the trunk. • Do not push items too far into the trunk, particu- larly when the top is retracted into its stowage area in the trunk. • Do not use the area near the tonneau cover for storage. Failure to follow these cautions can cause damage to the convertible top components, trunk contents, and the vehicle interior. 90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! (0°C). that it is clear of debris or other items. Before operating the power top: • Always check the tonneau cover area to be sure • Make sure the ambient temperature is above 32°F • Never attempt to lower a frozen convertible top. Wait until the top is thawed before lowering it into the stowage compartment. Lowering a cloth top at temperatures below 32°F (0°C) should be avoided. • Make sure the convertible top is dry before low- ering it into the stowage compartment. Lowering the top when damp, wet, or dirty can cause stains, mildew, and damage to the inside of your vehicle. • Make sure there is sufficient clearance of at least 7.5 ft. (2.2 m) for the top to move up. (Continued) CAUTION! (Continued) • To prevent striking a low ceiling or automatic door opener with the top, it is strongly recommended that you do not operate the power top inside a garage or parking structure. Failure to follow these cautions can cause damage to the convertible top components, trunk contents, and the vehicle interior. CAUTION! Failure to follow these cautions can cause damage to the convertible top components, trunk contents, and the vehicle interior: • Do not operate the power top with the hydraulic pump valve open. (Continued) CAUTION! (Continued) • Do not allow the top to remain in the suspended position. After approximately 10 minutes in the suspended position, the hydraulic pressure will release, which will allow the top and the trunk lid to lower. Pressing the power top switch will cancel this operation. • Always use a normal ice scraper to remove snow or ice from the rear window. Use of a sharp object or other tools could scratch the fabric or panels when removing snow or ice. • Always close the top when leaving your vehicle so as not to leave the interior exposed to potentially damaging outdoor conditions. (Continued) UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 CAUTION! (Continued) • Do not leave the top lowered for several weeks at a time. Close it occasionally to prevent discolora- tion in the folds of the fabric and to allow the creases to smooth out. This is especially important if the top was stowed when not completely dry. WARNING! Failure to follow these warnings can result in injuries that are serious or fatal to you, your passengers, and others around you: • Before operating the power top, make sure that no moving parts of the convertible top can injure a person or animal. (Continued) 92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) • Never place any extremities (hands, feet, etc.) near the convertible top components, the upper wind- shield area, the shelf area behind the rear seats, or the convertible top stowage area while raising or lowering the convertible top. • When using the power top button on RKE trans- mitter, if potential danger exists while lowering the top, release the button immediately to inter- rupt the operation. • When using the power top switch on the instru- ment panel, if potential danger exists while low- ering the top, release the switch immediately to interrupt the operation. (Continued) WARNING! (Continued) • When using the power top switch on the instru- ment panel, if potential danger exists while raising the top, release the switch immediately to inter- rupt the operation. • Only drive the vehicle with the convertible top completely closed and latched or fully lowered into its stowage compartment. • Do not operate the power top when the vehicle is in motion. Cargo Shield The cargo shield is located in the trunk. Before lowering the convertible top, you must unfold the cargo shield and seat the tabs at each end of the cargo shield in the V slots in the trunk liner. Doing so closes a switch that allows top operation. If the switch is not closed, a warning message displays in the instrument cluster to notify the driver. Positioning the Cargo Shield for Top Operation Pull the cargo shield toward you to begin unfolding the panels. Grasp the handle in the center of the outermost (top) panel and raise the cargo shield. Then, align and seat the tabs at each end of the cargo shield in the V slots in the trunk liner as shown in the illustration. CAUTION! Do NOT place items on cargo protector. Items placed on cargo protector will interfere with the top during operation and cause excessive damage to the top. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 Cargo Shield Positioning the Cargo Shield for Cargo Storage To maximize the storage space in the trunk, the cargo shield can be stowed in the forward portion of the trunk. 94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To stow the cargo shield, grasp the handle of the upright panel of the cargo shield, lifting the pins out of the V slots in the trunk trim. Continue folding the upright panel forward onto the horizontal panel, then grasp both panels and lift them to the forward, upright position in the trunk. NOTE: The convertible top will NOT operate with the cargo shield in the stowed position. Power Convertible Top Controls The power top switch is located on the instrument panel to the left of the steering column. Stowed Cargo Shield Power Top Switch There is also a power top button on the Remote Keyless Entry (RKE) transmitter for remotely lowering the power convertible top. Power Top Button UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 Lowering the Power Convertible Top Using the Power Top Switch NOTE: The power top switch will operate when the ignition switch is turned to the ON or ACC position and when in the power accessory delay. There are two Top Down switch positions. Press and hold the switch to the first detent. The system will lower all fully raised windows approximately 0.5 in (10 mm), lower the top to its fully retracted position, and then raise the windows. Press and hold the switch to the second detent. The system will lower all four windows and the top to their fully retracted positions. The driver has to press and hold the convertible top switch during the entire opening cycle, if there is an obstruction and the driver is alerted, the convertible top operation can be stopped by releasing the switch. 96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Using the Remote Keyless Entry Transmitter Steps 1 – 3must be performed within five NOTE: seconds. 1. Press and release the UNLOCK button on the RKE transmitter. 2. Press and release the POWER TOP button on the RKE transmitter. 3. Press and hold the POWER TOP button until the Power Top and All Windows Down feature is complete. Raising the Power Convertible Top Using the Power Top Switch NOTE: The power top switch will operate when the ignition switch is turned to the ON or ACC position and when in the power accessory delay. Press and hold the switch in the Top Up position until the operation of raising the top and latching it is complete, which is indicated by the system raising the windows and dis- playing “TOP DONE” in the odometer or “CONVERT- IBLE TOP COMPLETE” in the EVIC (if equipped). Using the Remote Keyless Entry Transmitter You cannot use the power top button on the RKE transmitter to raise the power convertible top. You must use the power top switch inside the vehicle to perform this operation. Manually Closing the power convertible top manually is a compli- cated and physically demanding procedure, and it re- quires a special tool to do so. In the event that you experience a malfunction when operating the power convertible top: 1. Read all of the Notes, Cautions, and Warning found under “Power Convertible Top Usage Precautions” to verify all operating conditions are met. 2. Check for Operation and Warning Messages as de- scribed under “Power Convertible Top Operation and Warning Messages.” If applicable, perform the related action to correct the condition present. 3. If Steps 1 and 2 do not resolve the problem, refer to “Emergency Bypass Mode”. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 It is recommended that you lower the convert- Wind Stop — If Equipped The Wind Stop installs in the backseat area of the vehicle. The Wind Stop will not interfere with power top opera- tion. Therefore, it can remain installed when the top is up. However, when not in use, the Wind Stop folds to allow for convenient storage underneath the cargo shield in the trunk. NOTE: ible top before installing or removing the Wind Stop. Installing the Wind Stop 1. Remove the Wind Stop from the trunk. 2. Unfold the Wind Stop framework. 3. Lay the small frame (1) flat on top of the large frame (2) and snap the two frames together by engaging the frame lock (3). 98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The frames must lie flat on each other in order to snap them together. 4. Pivot the small frame (1) away from the large frame (2) until the pivot lock (3) engages to lock the two frames in an L shape. 5. Unfold both stems at the rear of the large frame. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 6. Align and insert the stems into the slot in each trim panel. 100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 7. Align the pins at the front of the large frame with the hole in each trim panel. Slide the pins outward until fully extended into each hole. Disengage the pivot lock (1) to fold the small frame flat onto the large frame. Disengage the frame lock (2) to disconnect the small frame from the large frame. Removing and Storing the Wind Stop Reverse the installation procedure to remove, fold, and store the Wind Stop. However, note the following before doing so: Power Convertible Top Operation and Warning Messages When the appropriate conditions exist, the PTCM dis- plays various power convertible top operation and warn- ing messages in the Electronic Vehicle Information Center EVIC Message〫 EVIC Message Display Time〫 Odometer Message (< 5 mph [8 km/ h])〫〫 TOP nOT SECUrE Odometer Message Display Time〫〫 Until Op- eration is Complete Odometer Message (> 5 mph [8 km/ h])〫〫 — CONVERT- IBLE TOP NOT SE- CURED Until Op- eration is Complete UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 (EVIC) – if equipped, or in the Odometer for vehicles not equipped with the EVIC. Refer to the following chart for message related information: Chime Odometer Message Display Time〫〫 — — Condition Operator Action Required — The Sys- tem is Lowering or Raising the Top 102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE EVIC Message Display Time〫 9 sec. EVIC Message〫 CONVERT- IBLE TOP COMPLETE Odometer Message (< 5 mph [8 km/ h])〫〫 TOP DONE Odometer Message Display Time〫〫 Display Scrolls for 6 sec. Odometer Message (> 5 mph [8 km/ h])〫〫 — Odometer Message Display Time〫〫 — 9 sec. SECURE CARGO SHIELD SET CARGO SHIELD Display Scrolls for 9 sec. — — Chime Single Chime Single Chime Condition Operator Action Required The Sys- tem Com- pletes Op- eration of Lowering or Raising the Top The Top Fails to Move When Op- erating the Power Top Control — Position the Cargo Shield in the Trunk to Allow Top Op- eration UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 EVIC Message〫 CONVERT- IBLE TOP NOT SE- CURED EVIC Message Display Time〫 Until Op- eration is Complete Odometer Message (< 5 mph [8 km/ h])〫〫 TOP nOT SECUrE Odometer Message Display Time〫〫 Until Op- eration is Complete Odometer Message (> 5 mph [8 km/ h])〫〫 TOP nOT SECUrE Odometer Message Display Time〫〫 Until Op- eration is Complete Chime Single Chime Condition Operator Action Required Cycle Power Top Control The Sys- tem Fails to Com- plete Op- eration of Lowering or Raising the Top 104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE EVIC Message〫 EVIC Message Display Time〫 SPEED TOO HIGH 9 sec. Odometer Message (< 5 mph [8 km/ h])〫〫 SPEED TOO HIGH Odometer Message Display Time〫〫 Display Scrolls for 9 sec. Odometer Message (> 5 mph [8 km/ h])〫〫 TOP Odometer Message Display Time〫〫 6 sec. Chime Single Chime Condition Operator Action Required The Top Will Not Operate Unless the Vehicle is Stationary. You Are Operating the Power Top at a Vehicle Speed Greater Than 0 mph (0 km/h) UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 EVIC Message〫 TRUNK AJAR EVIC Message Display Time〫 Continu- ous Odometer Message (< 5 mph [8 km/ h])〫〫 DECK Odometer Message Display Time〫〫 Continu- ous Odometer Message (> 5 mph [8 km/ h])〫〫 DECK Chime Odometer Message Display Time〫〫 Continu- ous Single Chime 6 sec. CONVERT- IBLE TOP MAL- FUNCTION TOP FAIL Display Scrolls for 6 Seconds TOP 6 sec. Single Chime Condition Operator Action Required The Top Will Not Operate Unless the Trunk Lid is Closed Refer to Foot Note 〫〫〫 The Trunk Lid is Un- latched or Open The PTCM Activated the System LOCKOUT Feature 106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE EVIC Message〫 CONVERT- IBLE TOP MAL- FUNCTION EVIC Message Display Time〫 Until Fault is No Longer Detected or Re- paired Odometer Message Display Time〫〫 Odometer Message (< 5 mph [8 km/ h])〫〫 TOP FAIL Display Scrolls un- til Fault is No Longer Detected or Re- paired Odometer Message (> 5 mph [8 km/ h])〫〫 TOP Chime Single Chime Odometer Message Display Time〫〫 Display Flashes until Fault is No Longer Detected or Re- paired Condition Operator Action Required The PTCM Activated the System LOCKOUT Feature See your authorized dealer for service 〫 If so equipped. 〫〫 For vehicles not equipped with the EVIC. 〫〫〫 The PTCM will lockout the power convertible top system if the vehicle charging system is malfunction- ing, or the battery is run down, or the hydraulic pump is overheating. In addition, the system prohibits lower- ing the top when ambient temperature is at 0°F (-18°C) or lower and raising the top when ambient temperature is below -40°F (-40°C). UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 • If you are trying to lower the top and ambient temperature is 0°F (-18°C) or lower, wait until the temperature rises and the top is thawed and dry before operating the power top. A soft top should not be lowered at tem- peratures below 32°F (0°C). • If you are trying to raise the top and ambient temperature is below -40°F (-40°C), wait until the temperature rises before operating the power top. • If the vehicle charging system is malfunctioning, see your authorized dealer for service. • If the battery is run down, have it recharged and tested at your authorized dealer. • Hydraulic pump overheating can occur if you lower and raise the top consecutively (usually more than six or seven times depending upon the ambient temperature). Wait at least five minutes before operating the power top again. NOTE: If lockout occurs due to hydraulic pump overheating, the system will allow you to raise the top without waiting five minutes. However, do so only if necessary. 108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Emergency Bypass Mode (To Raise the Top Only) This procedure is only to be used to raise the top when the top cannot be returned to the UP (raised) position by pressing the POWER TOP switch or is in a position in which the vehicle cannot be driven. Please follow these emergency bypass instructions to return the top to the UP (raised) position. Press the POWER TOP switch in the Top Up direction five times within two seconds and hold the switch in the Top Up position for a minimum of two minutes. CAUTION! • Once this procedure has been completed and the top is in the UP (raised) position, see your autho- rized dealer. DO NOT exceed 40 mph (64 km/h). (Continued) CAUTION! (Continued) • Using the Emergency Bypass Mode could poten- tially damage the convertible top and should only be used to raise the power top to the UP (raised) position when the normal top operation is not functioning. If damage starts to occur while in the Emergency Bypass Mode, immediately release the power top switch and see your authorized dealer. NOTE: This procedure may take more time to fully raise and close the power top. It is not uncommon to see delays of up to 30 seconds before operation begins. MIRRORS Automatic Dimming Mirror This mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light next to the button will illuminate to indicate when the dimming feature is activated. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 1 — Auto Dimming Mirror Power Indicator 2 — On/Off Switch 3 — Auto Dimming Mirror Sensor CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean. 110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Outside Mirrors To receive maximum benefit, adjust the outside mirrors to center on the adjacent lane of traffic and a slight overlap of the view obtained from the inside mirror. NOTE: The passenger side convex outside mirror will give a much wider view to the rear, and especially of the lane next to your vehicle. WARNING! Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger side convex mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in the passenger side convex mirror. Power Mirrors The power mirror switch is located on the driver’s door trim. A rotary knob selects the left mirror, right mirror or off position. Power Mirror Adjust Switch After selecting a mirror, move the knob in the same direction you want the mirror to move. When finished, return the knob to the center “O” (Off) position to guard against accidentally moving a mirror position. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 Heated Mirrors — If Equipped These mirrors are heated to melt frost or ice. This feature is activated whenever you turn on the rear window defroster. Refer to “Rear Window Features” in “Understanding the Features of Your Vehicle” for further information. Mirror Directions 112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Vanity Mirror — If Equipped A vanity mirror is attached to the inside face of the sun visor. To use the mirror, rotate the sun visor downward and flip the mirror cover upward. Uconnect™ Phone — IF EQUIPPED Refer to “Uconnect™ Phone” in the Uconnect™ User Manual located on the DVD for further details. VOICE COMMAND — IF EQUIPPED Voice Command can be initiated by pressing the VR located on the radio or steering wheel button controls (if equipped). Refer to “Voice Command” in the Uconnect™ Phone User Manual located on the DVD for further details. Vanity Mirror SEATS Seats are a primary part of the Occupant Restraint System of the vehicle. They need to be used properly for safe operation of the vehicle. WARNING! • DO NOT allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Be sure everyone in your vehicle is in a seat and using a seat belt properly. Power Seats The power seat switch is on the outboard side of the seat near the floor. Use the switch to move the seat up, down, forward, rearward, or to tilt the seat. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 Power Seat Switch 114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust the seat only while the vehicle is parked. • Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured. Use the recliner only when the vehicle is parked. CAUTION! Do not place any article under any seat as it may cause damage to the seat controls. Heated Seats — If Equipped The driver and front passenger seats are heated. The controls for each heater are located in the instrument panel switch bank above the climate controls. After turning the ignition ON, you can choose from High, Low, or Off heat settings. Amber indicator lights in each switch indicate the level of heat in use. Two indicator lights will illuminate for High, one for Low and none for Off. Press the switch once to select High-level heat- ing. Press the switch a second time to select Low-level heating. Press the switch a third time to shut the heating elements Off. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 CAUTION! Repeated overheating of the seat could damage the heating element and/or degrade the material of the seat. WARNING! • Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, ex- haustion or other physical condition must exercise care when using the seat heater. It may cause burns even at low temperatures, especially if used for long periods of time. • Do not place anything on the seat that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat. Sitting in a seat that has been overheated could cause serious burns due to the increased surface temperature of the seat. 116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Recliner Adjustment The recliner control is on the outboard side of the seat. To recline the seat, lean forward slightly and lift the lever. Then lean back to the position desired and release the lever. To return the seatback to its normal upright posi- tion, lean forward and lift the lever. Release the lever once the seatback is in the upright position. Seatback Adjustment WARNING! • Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust the seat only while the vehicle is parked. • Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured. Use the recliner only when the vehicle is parked. Lumbar Support — If Equipped This feature allows you to increase or decrease the amount of lumbar support. The control lever is on the inboard side of the seat. Turn the control lever downward to increase and upward to decrease the desired amount of lumbar support. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 Lumbar Support Easy Entry Lever Easy Entry System The Easy Entry lever is located on upper seat belt anchor cover. Pull the lever upward to move the seat and seatback forward. When returning the seat to its normal position, the memory feature restores the seat position and seatback recline position to their current settings. 118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE On the driver seat, pull the lever upward to move the seatback forward. When returning the seatback to its normal position the memory feature restores the seatback recline position to its current setting. Adjusting Active Head Restraints Active Head Restraints can reduce the risk of injury in the event of a rear impact. The Active Head Restraint should be adjusted so the top of the head restraint is located above the top of your ear. Adjusted Head Restraint To raise the head restraint, pull upward on the head restraint (on some models, you may need to press the push button). To lower the head restraint, press the push button, located at the base of the head restraint, and push downward on the head restraint. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 For comfort the Active Head Restraints can be tilted forward and backward. To tilt the head restraint closer to the back of your head, pull outward on the bottom of the head restraint. Push rearward on the bottom of the head restraint to move the head restraint away from your head. Push Button Active Head Restraint (Normal Position) 120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Active Head Restraint (Tilted) NOTE: • The head restraints should only be removed by quali- fied technicians, for service purposes only. If either of the head restraints require removal, see your autho- rized dealer. • In the event of deployment of an Active Head Re- straint, refer to “Occupant Restraints/Resetting Active Head Restraints (AHR)” in “Things to Know Before Starting Your Vehicle” for further information. WARNING! • Driving a vehicle with the head restraints removed or improperly adjusted could cause serious injury or death in the event of a collision. The head restraints should always be checked prior to oper- ating the vehicle and never adjusted while the vehicle is in motion. Always adjust the head restraints when the vehicle is in PARK. (Continued) WARNING! (Continued) • Do not place items over the top of the Active Head Restraint, such as coats, seat covers or portable DVD players. These items may interfere with the operation of the Active Head Restraint in the event of an accident and could result in serious injury or death. • Active Head Restraints may be deployed if they are struck by an object such as a hand, foot or loose cargo. To avoid accidental deployment of the Ac- tive Head Restraint ensure that all cargo is se- cured, as loose cargo could contact the Active Head Restraint during sudden stops. Failure to follow this warning could cause personal injury if the Active Head Restraint is deployed. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 TO OPEN AND CLOSE THE HOOD Two latches must be released to open the hood. 1. Pull the hood release lever located under the left side of the instrument panel. Hood Release Lever 122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Move to the outside of the vehicle and lift the second- ary latch underneath the center front edge of the hood and raise the hood. Hood Prop Rod Hole Location Before closing the hood, make sure to stow the prop rod in its proper location. Hood Safety Catch Use the hood prop rod to secure the hood in the open position. Place the upper end of the prop rod in the hole on the underside of the hood. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 LIGHTS Multifunction Lever The multifunction lever on the left side of the steering column controls the operation of the headlights, parking lights, turn signal lights, instrument panel lights, instru- ment panel light dimming, interior lights and fog lights (if equipped). CAUTION! To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the center of the hood to ensure that both latches engage. WARNING! Be sure the hood is fully latched before driving your vehicle. If the hood is not fully latched, it could open when the vehicle is in motion and block your vision. Failure to follow this warning could result in serious injury or death. Multifunction Lever 124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlights And Parking Lights Turn the end of the multifunction lever to the first detent for parking light operation. Turn the end of the lever to the second detent for headlight operation. Headlight Switch Lights-On Reminder If the headlights or parking lights are on after the ignition is turned to the LOCK position, a chime will sound to alert the driver when the driver’s door is opened. Automatic Headlights — If Equipped This system automatically turns the headlights on or off according to ambient light levels. To turn the system on, turn the end of the multifunction lever to the AUTO position. When the system is on, the Headlight Time Delay feature is also on. This means the headlights will stay on for up to 90 seconds after you turn the ignition switch to the LOCK position. To turn the Automatic System off, turn the end of the multifunction lever out of the AUTO position. NOTE: The engine must be running before the head- lights will turn on in the Automatic mode. Headlights with Wipers (Available with Automatic Headlights Only) When this feature is active, the headlights will turn on approximately 10 seconds after the wipers are turned on if the multifunction lever is placed in the AUTO position. In addition, the headlights will turn off when the wipers are turned off if they were turned on by this feature. The Headlights with Wipers feature can be turned on or off through the Electronic Vehicle Information Center (EVIC) — if equipped. Refer to “Electronic Vehicle Infor- mation Center (EVIC)/Customer-Programmable Fea- tures” in “Understanding Your Instrument Panel” for further information. Headlight Time Delay — If Equipped This feature is particularly useful when exiting your vehicle in an unlit area. It provides the safety of headlight illumination for about 90 seconds after turning the igni- tion switch to the LOCK position. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 To activate the delay, turn the ignition switch to the LOCK position while the headlights are still on. Then, turn off the headlights within 45 seconds. The delay interval begins when you turn off the headlights. Only the headlights will illuminate during this time. If you turn the headlights, parking lights, or ignition switch ON again, the system will cancel the delay. If you turn the headlights off before the ignition, they will turn off in the normal manner. The Headlight delay time is programmable on vehicles equipped with the Electronic Vehicle Information Center (EVIC). Refer to “Electronic Vehicle Information Center (EVIC)/Customer-Programmable Features” in “Under- standing Your Instrument Panel” for further information. 126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Instrument Panel Dimmer Rotate the center portion of the lever to the extreme bottom position to fully dim the instrument panel lights and prevent the interior lights from illuminating when a door is opened. Rotate the center portion of the lever up to increase the brightness of the instrument panel lights when the park- ing lights or headlights are on. Rotate the center portion of the lever upward to the next detent position to brighten the odometer and radio when the parking lights or headlights are on. Rotate the center portion of the lever upward to the last detent to turn on the interior lighting. Dimmer Control Fog Lights — If Equipped To activate the front fog lights, turn on the parking lights or the low beam headlights and pull out on the end of the multifunction lever. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 NOTE: The front fog lights will only operate with the headlights on low beam. Selecting high beam headlights will turn off the front fog lights. Daytime Running Lights — If Equipped The high beam headlights will turn on as Daytime Running Lights (DRL) and operate at lower intensity whenever the ignition is ON, the engine is running, the headlight switch is off, the parking brake is released and the shift lever is in any position except PARK. NOTE: The Daytime Running Lights will turn off automatically when a turn signal is in operation and turn on again when the turn signal is not operating. Front Fog Light Control 128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turn Signals Move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights. Turn Signal Control Lane Change Assist Tap the lever up or down once, without moving beyond the detent, and the turn signal (right or left) will flash three times then automatically turn off. High/Low Beam Switch Push the multifunction lever away from you to switch the headlights to high beam. Pull the multifunction lever toward you, to switch the headlights back to low beam. Flash-To-Pass You can signal another vehicle with your headlights by lightly pulling the multifunction lever toward you. This will cause the headlights to turn on at high beam and remain on until the lever is released. If the multifunction lever is held in the Flash- NOTE: To-Pass position for more than 15 seconds, the high beams will shut off. If this occurs, wait 30 seconds before activating the Flash-To-Pass function again. Interior Lights Two courtesy/reading lights are located in the bottom of the rearview mirror. You can turn these lights on and off from the switches in the mirror or from the dimmer control in the multifunction lever. These lights are also controlled automatically by the Illuminated Entry System. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 A courtesy light is also found in the rear of the center console. You can turn this light on and off from the dimmer control in the multifunction lever. This light is also controlled automatically by the Illuminated Entry System. Battery Saver Feature To protect the battery, the interior lights will turn off automatically 10 minutes after the ignition switch is moved to the LOCK position. This will occur if the interior lights were switched on manually or are on because a door is open. Courtesy/Reading Light Switches 130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WINDSHIELD WIPERS AND WASHERS The windshield wiper/washer control lever is located on the right side of the steering column. Windshield Wiper/Washer Lever Rotate the end of the lever to the LO position for low-speed wiper operation, or to the HI position for high-speed wiper operation. Changing Wiper Speeds NOTE: The wipers will automatically return to the “Park” position if you turn the ignition switch OFF while they are operating. The wipers will resume operation when you turn the ignition switch to the ON position again. CAUTION! • Turn the windshield wipers off when driving through an automatic car wash. Damage to the windshield wipers may result if the wiper control is left in any position other than off. • Always remove any buildup of snow that prevents the windshield wiper blades from returning to the off position. If the windshield wiper control is turned off and the blades cannot return to the off position, damage to the wiper motor may occur. Intermittent Wiper System Use the intermittent wiper system when weather condi- tions make a single wiping cycle with a variable pause between cycles desirable. Rotate the end of the wind- shield wiper/washer control lever to the first detent, and then turn the end of the lever to select the desired delay interval. There are five delay settings, which allow you to UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 regulate the wipe interval from a minimum of one cycle every second to a maximum of approximately 18 seconds between cycles. Changing Intermittent Settings 132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Sudden loss of visibility through the windshield could lead to an accident. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with defroster before and during wind- shield washer use. Mist Feature Push downward on the windshield wiper/washer con- trol lever to activate a single wipe cycle to clear the windshield of road mist or spray from a passing vehicle. The wipers will continue to operate until you release the lever. Mist Control Headlights with Wipers (Available with Auto Headlights Only) When this feature is active, the headlights will turn on approximately 10 seconds after the wipers are turned on if the multifunction lever (on the left side of the steering column) is placed in the AUTO position. In addition, the headlights will turn off when the wipers are turned off if they were turned on by this feature. The Headlights with Wipers feature can be turned on or off through the Electronic Vehicle Information Center (EVIC) — if equipped. Refer to “Electronic Vehicle Infor- mation Center (EVIC)/Personal Settings (Customer- Programmable Features)” in “Understanding Your In- strument Panel” for further information. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 Windshield Washers To use the washer, pull the windshield wiper/washer control lever toward you and hold it for as long as washer spray is desired. If you activate the washer while the wiper control is in the delay range, the wipers will operate in low-speed for two wipe cycles after releasing the lever and then resume the intermittent interval previously selected. If you activate the washer while the wiper control is in the off position, the wipers will operate for two wipe cycles and then turn off. 134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE TILT/TELESCOPING STEERING COLUMN This feature allows you to tilt the steering column upward or downward. It also allows you to lengthen or shorten the steering column. The tilt/telescoping control handle is located below the steering wheel at the end of the steering column. To unlock the steering column, push the control handle downward. To tilt the steering column, move the steering wheel upward or downward as desired. To lengthen or shorten the steering column, pull the steering wheel outward or push it inward as desired. To lock the steering column in position, pull the control handle upward until fully engaged. WARNING! Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the vehicle. Be sure the steering column is locked before driving your ve- hicle. Failure to follow this warning may result in serious injury or death. ELECTRONIC SPEED CONTROL When engaged, the Electronic Speed Control takes over the accelerator operation at speeds greater than 25 mph (40 km/h). The Electronic Speed Control lever is located on the right side of the steering wheel. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 In order to ensure proper operation, the Elec- NOTE: tronic Speed Control System has been designed to shut down if multiple Speed Control functions are operated at the same time. If this occurs, the Electronic Speed Control System can be reactivated by pushing the Electronic Speed Control ON/OFF button and resetting the desired vehicle set speed. To Activate Push and release the ON/OFF button located on the end of the Electronic Speed Control lever. The CRUISE indi- cator in the instrument cluster will illuminate. To turn the system off, push and release the ON/OFF button a second time. The CRUISE indicator will turn off. Be sure to turn the system off when not in use. NOTE: The Electronic Speed Control system will auto- matically turn off when the ignition is turned OFF. Electronic Speed Control Lever 136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Leaving the Electronic Speed Control on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system off when you are not using it. To Set a Desired Speed Turn the Electronic Speed Control ON. When the vehicle reaches the speed desired, press down on the lever and release SET DECEL. Release the accelerator and the vehicle will operate at the selected speed. NOTE: • The vehicle must be traveling at least 25 mph • The vehicle should be traveling at a steady speed and on level ground before pressing the lever SET DECEL. (40 km/h) for the Electronic Speed Control to set. To Deactivate A soft tap on the brake pedal, or pulling the Electronic Speed Control lever toward you (CANCEL), or normal brake pressure while slowing the vehicle will deactivate the Electronic Speed Control without erasing the set speed from memory. Pressing the ON/OFF button or turning off the ignition erases the set speed from memory. To Resume Speed If you deactivated the Electronic Speed Control without erasing the set speed from memory and your vehicle speed is above 20 mph (32 km/h) you can resume the previous set speed. To do so, push the lever up and release RESUME ACCEL, and then remove your foot from the accelerator pedal. To Vary the Speed Setting When the Electronic Speed Control is set, you can in- crease speed by pushing up and holding the RESUME ACCEL lever. If the lever is continually held in the RESUME ACCEL position, the set speed will continue to increase until the lever is released, then the new set speed will be established. Tapping RESUME ACCEL once will result in a 1 mph (2 km/h) speed increase. Each time the lever is tapped, speed increases so that tapping the lever three times will increase speed by 3 mph (5 km/h), etc. To decrease speed while the Electronic Speed Control is set, push down and hold the SET DECEL lever. If the lever is continually held in the SET DECEL position, the set speed will continue to decrease until the lever is released. Release the lever when the desired speed is reached, and the new set speed will be established. Tapping the SET DECEL lever once will result in a 1 mph (2 km/h) speed decrease. Each time the button is tapped, speed decreases. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 WARNING! Electronic Speed Control can be dangerous where the system cannot maintain a constant speed. Your ve- hicle could go too fast for the conditions, and you could lose control. An accident could be the result. Do not use Electronic Speed Control in heavy traffic or on roads that are winding, icy, snow-covered, or slippery. To Accelerate for Passing Press the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. Using Electronic Speed Control On Hills NOTE: The Electronic Speed Control system maintains speed up and down hills. A slight speed change on moderate hills is normal. 138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE On steep hills, a greater speed loss or gain may occur so it may be preferable to drive without Electronic Speed Control. The HomeLink威 buttons that are located in the headliner or sun visor designate the three different HomeLink威 channels. WARNING! Electronic Speed Control can be dangerous where the system cannot maintain a constant speed. Your ve- hicle could go too fast for the conditions, and you could lose control. An accident could be the result. Do not use Electronic Speed Control in heavy traffic or on roads that are winding, icy, snow-covered or slippery. GARAGE DOOR OPENER — IF EQUIPPED HomeLink威 replaces up to three remote controls (hand- held transmitters) that operate devices such as garage door openers, motorized gates, lighting or home security systems. The HomeLink威 unit operates off your vehicle’s battery. HomeLink威 Buttons NOTE: HomeLink威 is disabled when the Vehicle Secu- rity Alarm is active. WARNING! • Your motorized door or gate will open and close while you are training the universal transceiver. Do not train the transceiver if people, pets or other objects are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by Federal safety standards. This includes most garage door opener models manufactured after 1982. Do not use a garage door opener without these safety features. Call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for safety infor- mation or assistance. • Vehicle exhaust contains carbon monoxide, a dan- gerous gas. Do not run your vehicle in the garage while training the transceiver. Exhaust gas can cause serious injury or death. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 Programming HomeLink姞 Before You Begin If you have not trained any of the HomeLink威 buttons, erase all channels before you begin training. To do this, press and hold the two outside buttons for up to 20 seconds until the red indicator flashes. It is recommended that a new battery be placed in the handheld transmitter of the device that is being copied to HomeLink威 for more efficient training and accurate transmission of the radio-frequency signal. Your vehicle should be parked outside of the garage when programming. Begin Programming 1. Turn the ignition switch to the ON/RUN position. 2. Hold the battery side of the handheld transmitter away from the HomeLink威 button you wish to program. 140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Place the handheld transmitter 1 to 3 in (3 to 8 cm) away from the HomeLink威 button you wish to program while keeping the indicator light in view. 3. Simultaneously press and hold both the chosen HomeLink威 button and the handheld transmitter button until the HomeLink威 indicator changes from a slow to a rapidly blinking light, then release both the HomeLink威 and handheld transmitter buttons. Watch for the HomeLink威 indicator to change flash rates. When it changes, it is programmed. It may take up to 30 seconds or longer in rare cases. The garage door may open and close while you train. NOTE: • Some gate operators and garage door openers may require you to replace Step 3 with procedures noted in the “Gate Operator/Canadian Programming” section. • After training a HomeLink威 channel, if the garage door does not operate with HomeLink威 and the ga- rage door opener was manufactured after 1995, the garage door opener may have a rolling code. If so, proceed to Step 5 “Programming A Rolling Code System.” 4. Press and hold the just-trained HomeLink威 button and observe the indicator light. If the indicator light stays on constantly, programming is complete and the garage door (or device) should activate when the HomeLink威 button is pressed. If the indicator light blinks rapidly for two seconds and then turns to a constant light, proceed to Step 5 “Pro- gramming A Rolling Code System.” 5. Programming A Rolling Code System At the garage door opener motor (in the garage), locate the “Learn” or “Training” button. This can usually be found where the hanging antenna wire is attached to the garage door opener motor. It is NOT the button normally used to open and close the door. Training The Garage Door Opener 1 — Door Opener 2 — Training Button UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 6. Firmly press and release the LEARN or TRAINING button. The name and color of the button may vary by manufacturer. NOTE: You have 30 seconds in which to initiate the next step after the LEARN button has been pressed. 7. Return to the vehicle and press the programmed HomeLink威 button twice (holding the button for two seconds each time). If the device is plugged in and activates, programming is complete. If the device does not activate, press the button a third time (for two seconds) to complete the training. If you have any problems, or require assistance, please call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for information or assistance. To program the remaining two HomeLink威 buttons, repeat each step for each remaining button. DO NOT erase the channels. and release 142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Using HomeLink威 To operate, press the programmed HomeLink威 button. Activation will now occur for the trained device (i.e., garage door opener, gate operator, security system, entry door lock, home/office lighting, etc.,). The handheld transmitter of the device may also be used at any time. Reprogramming a Single HomeLink威 Button To reprogram a channel that has been previously trained, follow these steps: 1. Turn the ignition switch to the ON/RUN position. 2. Press and hold the desired HomeLink威 button until the indicator light begins to flash after 20 seconds. Do not release the button. 3. Without releasing the button, proceed with Program- ming HomeLink威 Step 2 and follow all remaining steps. Gate Operator/Canadian Programming Canadian radio frequency laws require transmitter sig- nals to time-out (or quit) after several seconds of trans- mission – which may not be long enough for HomeLink威 to pick up the signal during programming. Similar to this Canadian law, some U.S. gate operators are designed to time-out in the same manner. It may be helpful to unplug the device during the cycling process to prevent possible overheating of the garage door or gate motor. If you are having difficulties programming a garage door opener or a gate operator, replace “Programming HomeLink威” Step 3, with the following: 3. Continue to press and hold the HomeLink威 button, while you press and release (“cycle”), your handheld transmitter every two seconds until HomeLink威 has successfully accepted the frequency signal. The indica- tor light will flash slowly and then rapidly when fully trained. If you unplugged the device for training, plug it back in at this time. Then proceed with Step 4 under “Programming HomeLink威,” earlier in this section. Security It is advised to erase all channels before you sell or turn in your vehicle. To do this, press and hold the two outside buttons for 20 seconds until the red indicator flashes. Note that all channels will be erased. Individual channels cannot be erased. The HomeLink威 Universal Transceiver is disabled when the Vehicle Security Alarm is active. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 Troubleshooting Tips If you are having trouble programming HomeLink威, here are some of the most common solutions: • Replace the battery in the original transmitter. • Press the LEARN button on the Garage Door Opener • Did you unplug the device for training, and remember to complete the training for a Rolling Code. to plug it back in? If you have any problems, or require assistance, please call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for information or assistance. General Information This device complies with FCC rules Part 15 and Industry Canada RSS-210. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. This device must accept any interference that may be received including interference that may cause undesired operation. NOTE: • The transmitter has been tested and it complies with FCC and IC rules. Changes or modifications not expressly approved by the party responsible for com- pliance could void the user’s authority to operate the device. • The term IC before the certification/registration num- Industry Canada technical ber only signifies that specifications were met. ELECTRICAL POWER OUTLETS There are two 12 Volt (13 Amp) electrical power outlets on this vehicle. Both of the power outlets are protected by a fuse. NOTE: Do not exceed the maximum power of 160 Watts (13 Amps) at 12 Volts. If the 160 Watt (13 Amp) power rating is exceeded the fuse protecting the system will need to be replaced. The instrument panel power outlet, located below the climate control knobs, has power available only when the ignition is ON. This power outlet will also operate a conventional cigar lighter unit. If desired, the instrument panel power outlet NOTE: can be converted by your authorized dealer to provide power with the ignition switch while in the LOCK position. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 Instrument Panel Power Outlet The center console power outlet is powered directly from the battery (power available at all times). Items plugged into this power outlet may discharge the battery and/or prevent the engine from starting. Center Console WARNING! To avoid serious injury or death: • Only devices designed for use in this type of outlet should be inserted into any 12 Volt outlet. (Continued) 146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) • Do not touch with wet hands. • Close the lid when not in use and while driving • If this outlet is mishandled, it may cause an the vehicle. electric shock and failure. CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting. (Continued) CAUTION! (Continued) • Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.) will degrade the battery even more quickly. Only use these inter- mittently and with greater caution. • After the use of high power draw accessories, or long periods of the vehicle not being started (with accessories still plugged in), the vehicle must be driven a sufficient length of time to allow the generator to recharge the vehicle’s battery. CIGAR LIGHTER AND ASH RECEIVER — IF EQUIPPED An optional ash receiver is available from your autho- rized dealer and will fit in the center console front cupholder. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 CAUTION! For vehicles equipped with the heated and cooled cupholder, locate the cup holder ash receiver in the forward cupholder. The optional ash receiver also comes with a cigar lighter. You may use the power outlet, located in the instrument panel below the climate control knobs, or in the bottom of the console compartment, for this cigar lighter. Ash Receiver 148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CUPHOLDERS Front Seat Cupholder The cupholder in the center console will accommodate either two large size cups or two 20 oz. (.5 L) bottles or cans. The one-piece insert can be removed easily for cleaning. An optional removable ashtray may be located in one of the cupholders. Rear Seat Cupholders Cupholders for the rear seat occupants are located in the armrests. Each cupholder is capable of holding up to a 20 oz. (.5 L) bottle or can. Front Cupholders Rear Seat Cupholder WARNING! If containers of hot liquid are place in the cupholder, they can spill when the door is closed, burning the occupants. Be careful when closing the doors to avoid injury. CONSOLE FEATURES Storage The center console contains a cubby bin with flip-down cover located below the climate controls. This compart- ment also contains a 12 Volt electrical outlet. WARNING! Do not place ashes inside the cubby bin located on the center console. A fire leading to bodily injury could result. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 Cubby Bin Two separate storage compartments are also located underneath the armrest. 150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 1 — Release button for top compartment 2 — Release button for bottom compartment 3 — Top Compartment 4 — Bottom Compartment. You can access this compartment directly, without first exposing the upper compartment, by oper- ating the Release Button for the bottom compartment with the armrest down. The top compartment holds small items, such as a pen and note pad, while the larger bottom compartment will hold CDs and alike. The bottom compartment also con- tains a 12 Volt power outlet and a molded-in coin holder (designed to hold various size coins). The console’s front opening lid allows for easy access to these compartments. NOTE: • A notch in the side of the console base allows for use of a cellular phone while it is plugged into the power outlet with the armrest latched down. • The power outlet can also energize the cigar lighter in the optional cup holder ash receiver. Sliding Armrest — If Equipped On some models the center console armrest slides for- ward and rearward for added user comfort. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 REAR WINDOW FEATURES Rear Window Defroster The rear window defroster button is located on the climate control (Mode) knob. Press this button to turn on the rear window defroster and the heated outside mirrors (if equipped). An indicator in the button will illuminate when the rear window defroster is on. The rear window defroster automatically turns off after ap- proximately 10 minutes. For an additional five minutes of operation, press the button a second time. NOTE: To prevent excessive battery drain, use the rear window defroster only when the engine is operating. Arm Rest 152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Failure to follow these cautions can cause damage to the heating elements: • Use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements. Labels can be peeled off after soaking with warm water. • Do not use scrapers, sharp instruments, or abra- sive window cleaners on the interior surface of the window. • Keep all objects a safe distance from the window. UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 Instrument Panel Features 䡵 Instrument Cluster 䡵 Instrument Cluster Descriptions 䡵 Electronic Vehicle Information Center (EVIC) – . . . . . . . . . . . . . . . 156 . . . . . . . . . . . . . . . . . . . . 157 . . . . . . . . . . . 158 If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 172 ▫ Electronic Vehicle Information Center (EVIC) Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . 173 ▫ Oil Change Required — If Equipped . . . . . . 174 ▫ Trip Functions . . . . . . . . . . . . . . . . . . . . . . 175 ▫ Compass Display . . . . . . . . . . . . . . . . . . . . 176 ▫ Personal Settings (Customer-Programmable Features) . . . . . . . . . . . . . . . . . . . . . . . . . . 179 䡵 Setting The Analog Clock . . . . . . . . . . . . . . . . 182 䡵 Media Center 230 (REQ) — AM/FM Stereo Radio And 6–Disc CD/DVD Changer (MP3/WMA AUX Jack) . . . . . . . . . . . . . . . . . . 182 ▫ Operating Instructions - Radio Mode . . . . . . 183 ▫ Operation Instructions - (Disc Mode For CD And MP3/WMA Audio Play, DVD-Video) . . . 191 ▫ Notes On Playing MP3/WMA Files . . . . . . . 193 154 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ List Button (Disc Mode For MP3/WMA Play) . . . . . . . . . . . . . . . . . . . . 195 ▫ Info Button (Disc Mode For MP3/WMA Play) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195 䡵 Media Center 730N/430 (RER/REN/RBZ) — AM/FM Stereo Radio And CD/DVD/HDD/ NAV — If Equipped . . . . . . . . . . . . . . . . . . . . 198 ▫ Operating Instructions — Voice Command System — If Equipped . . . . . . . . . . . . . . . . . 198 ▫ Operating Instructions — Uconnect™ Phone — If Equipped . . . . . . . . . . . . . . . . . . . . . . 198 ▫ Clock Setting Procedure — RBZ Radio . . . . . 198 ▫ Clock Setting Procedure — RER/REN Radio . . . . . . . . . . . . . . . . . . . . . 200 䡵 Media Center 130 (RES) — AM/FM Stereo Radio With CD Player (MP3 AUX Jack). . . . . . . 202 ▫ Operating Instructions — Radio Mode . . . . . 202 ▫ Operation Instructions — CD Mode For CD And MP3 Audio Play . . . . . . . . . . . . . . . . . 205 ▫ Notes On Playing MP3 Files . . . . . . . . . . . . 208 ▫ Operation Instructions - Auxiliary Mode . . . . 210 䡵 Media Center 130 (RES/RSC) — AM/FM Stereo Radio With CD Player (MP3 AUX Jack) And Sirius Radio . . . . . . . . . . . . . . . . . . . . . . 211 ▫ Operating Instructions — Radio Mode . . . . . 211 ▫ Operation Instructions — CD Mode For CD And MP3 Audio Play . . . . . . . . . . . . . . . . . 217 ▫ Notes On Playing MP3 Files . . . . . . . . . . . . 219 ▫ List Button (CD Mode For MP3 Play) . . . . . . 222 ▫ Info Button (CD Mode For MP3 Play) . . . . . . 222 ▫ Operating Instructions - Uconnect™ Phone (If Equipped) . . . . . . . . . . . . . . . . . . . . . . . 223 䡵 Uconnect™ Multimedia (Satellite Radio) — If Equipped (REN/REQ/RER/RBZ/RES Radios Only). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223 ▫ System Activation . . . . . . . . . . . . . . . . . . . . 223 ▫ Electronic Serial Number/Sirius Identification Number (ESN/SID) . . . . . . . . . 224 ▫ Selecting Uconnect™ Multimedia (Satellite) Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224 ▫ Satellite Antenna . . . . . . . . . . . . . . . . . . . . . 224 ▫ Reception Quality . . . . . . . . . . . . . . . . . . . . 225 ▫ Operating Instructions - Uconnect™ Multimedia (Satellite) Mode . . . . . . . . . . . . . 225 ▫ Operating Instructions - Uconnect™ Phone (If Equipped) . . . . . . . . . . . . . . . . . . . . . . . 227 UNDERSTANDING YOUR INSTRUMENT PANEL 155 䡵 Remote Sound System Controls — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 228 ▫ Right-Hand Switch Functions . . . . . . . . . . . . 228 ▫ Left-Hand Switch Functions For Radio Operation . . . . . . . . . . . . . . . . . . . . . . . . . . 229 ▫ Left-Hand Switch Functions For Media (i.e., CD) Operation . . . . . . . . . . . . . . . . . . . . . . 229 䡵 CD/DVD Disc Maintenance . . . . . . . . . . . . . . 229 䡵 Radio Operation And Cellular Phones . . . . . . . 230 䡵 Climate Controls . . . . . . . . . . . . . . . . . . . . . . 230 ▫ Manual Heating And Air Conditioning . . . . . 230 ▫ Automatic Temperature Control (ATC) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 235 ▫ Operating Tips . . . . . . . . . . . . . . . . . . . . . . 240 156 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT PANEL FEATURES 1 — Air Outlet 2 — Side Window Demister Outlet 3 — Instrument Cluster 4 — Ignition Switch 5 — Analog Clock 6 — Radio 7 — Passenger Airbag 8 — Glove Compartment 9 — Heated Seat Switch – If Equipped 10 — Electronic Stability Control Off Button – If Equipped 11 — Hazard Switch 12 — Storage Compartment 13 — Climate Control 14 — Trunk Release Button 15 — Power Top Switch INSTRUMENT CLUSTER UNDERSTANDING YOUR INSTRUMENT PANEL 157 158 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS 1. Temperature Gauge The temperature gauge shows engine coolant tempera- ture. Any reading below the red area of the gauge shows that the engine cooling system is operating properly. The gauge pointer may show a higher than normal tempera- ture when driving in hot weather, up mountain grades, in heavy stop and go traffic, or when towing a trailer. If the pointer rises to the H (red) mark, the instrument cluster will sound a chime. Pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the H (red) mark, turn the engine off immediately and call for service. There are steps that you can take to slow down an impending overheat condition. If your air conditioning is on, turn it off. The air conditioning system adds heat to the engine cooling system and turning off the A/C removes this heat. You can also turn the Temperature control to maximum heat, the Mode control to Floor and the Fan control to High. This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system. 2. Fuel Door Reminder This is a reminder that the Fuel Filler Door is located on the left side of the vehicle. 3. Fuel Gauge When the ignition switch is in the ON position, the pointer will show the level of fuel remaining in the fuel tank. 4. Speedometer Indicates the vehicle speed in miles per hour (MPH) and kilometers per hour (km/h). 5. Low Fuel Light When the fuel level drops to approximately 2.0 gal- lons (7.6 Liters), the fuel symbol will light and a single chime will sound. NOTE: This light will remain on until a minimum of approximately 3.0 gallons (11.3 Liters) of fuel is added. 6. Charging System Light This light shows the status of the electrical charg- ing system. The light should come on briefly when the ignition is first turned on and remain on briefly as a bulb check. If the light stays on or comes on while driving, turn off some of the vehicle’s electrical devices, such as the Front Fog Lights or Rear Window Defroster. If the Charging System Light remains on, it means that the vehicle is experiencing a problem with the charging system. Obtain SERVICE IMMEDIATELY. See your local authorized dealer. UNDERSTANDING YOUR INSTRUMENT PANEL 159 If jump starting is required, refer to “Jump Starting Procedures” in “What To Do In Emergencies”. 7. Airbag Warning Light The light comes on and remains on for six to eight seconds as a bulb check when the ignition switch is first turned ON. If the light does not turn on during starting, stays on, or turns on while driving, have the system inspected by an autho- rized dealer. Refer to “Occupant Restraints” in “Things To Know Before Starting Your Vehicle” for further infor- mation. 8. Seat Belt Reminder Light When the ignition switch is first turned ON, this light will come on for about six seconds. A chime will sound if you have not pulled the shoulder belt out of the retractor. This is a reminder to “buckle up”. If 160 UNDERSTANDING YOUR INSTRUMENT PANEL you do not buckle up, the light will remain on. Refer to “Occupant Restraints” in “Things To Know Before Start- ing Your Vehicle” for further information. 9. Oil Pressure Warning Light This light indicates low engine oil pressure. The light will come on and remain on when the ignition switch is turned from the OFF to the ON position, and the light will turn off after the engine is started. If the bulb does not come on during starting, have the system checked by an authorized dealer. If the light comes on and remains on while driving, stop the vehicle and shut off the engine. DO NOT OPERATE THE VEHICLE UNTIL THE CAUSE IS CORRECTED. The light does not show the quantity of oil in the engine. This can be determined using the procedure shown in “Maintaining Your Vehicle”. 10. Engine Temperature Warning Light This light warns of an overheated engine condi- tion. If the engine is critically hot, a warning chime will sound 10 times. After the chime turns off, the engine will still be critically hot until the light goes out. 11. Brake Warning Light This light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on, it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the anti-lock brake system. The dual brake system provides a reserve braking capac- ity in the event of a failure to a portion of the hydraulic system. Failure of either half of the dual brake system is indicated by the Brake Warning Light which will turn on when the brake fluid level in the master cylinder has dropped below a specified level. The light will remain on until the cause is corrected. NOTE: The light may flash momentarily during sharp cornering maneuvers which change fluid level condi- tions. The vehicle should have service performed, and the brake fluid level checked. If brake failure is indicated, immediate repair is neces- sary. WARNING! Driving a vehicle with the brake light on is danger- ous. Part of the brake system may have failed. It will take longer to stop the vehicle. You could have an accident. Have the vehicle checked immediately. Vehicles equipped with Anti-Lock brakes (ABS), are also equipped with Electronic Brake Force Distribution (EBD). UNDERSTANDING YOUR INSTRUMENT PANEL 161 In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light. Immediate repair to the ABS system is required. The operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON position. The light should illuminate for approxi- mately three seconds. The light should then turn off unless the parking brake is applied or a brake fault is detected. If the light does not illuminate, have the light inspected by an authorized dealer. The light also will turn on when the parking brake is applied with the ignition switch in the ON position. NOTE: This light shows only that the parking brake is applied. It does not show the degree of brake application. 162 UNDERSTANDING YOUR INSTRUMENT PANEL 12. Tachometer The silver area of the scale shows the permissible engine revolutions-per-minute (RPM x 1000) for each gear range. Before reaching the red area, ease up on the accelerator to prevent engine damage. 13. Shift Lever Indicator The Shift Lever Indicator is self-contained within the instrument cluster. It displays the gear position of the automatic transmission. NOTE: You must apply the brakes before shifting from PARK. 14. Odometer / Trip Odometer Display Area

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2010 Chrysler Sebring Convertible Owners Manual