2004 Chevrolet Tracker Owners Manual

Download PDF Manual
{CAUTION: Fuel vapor burns violently and a fuel ﬁre can cause bad injuries. To help avoid injuries to you and others, read and follow all the instructions on the pump island. Turn off your engine when you are refueling. Do not smoke if you are near fuel or refueling your vehicle. Keep sparks, ﬂames and smoking materials away from fuel. Do not leave the fuel pump unattended when refueling your vehicle — this is against the law in some places. Keep children away from the fuel pump; never let children pump fuel. The fuel cap is located behind a hinged door on the passenger’s side of your vehicle. 5-7 {CAUTION: If you spill fuel and then something ignites it, you could be badly burned. Fuel can spray out on you if you open the fuel cap too quickly. This spray can happen if your tank is nearly full, and is more likely in hot weather. Open the fuel cap slowly and wait for any “hiss” noise to stop. Then unscrew the cap all the way. Be careful not to spill fuel. Don’t top off or overﬁll your tank, and wait a few seconds after you’ve ﬁnished pumping before you remove the nozzle. Clean fuel from painted surfaces as soon as possible. See Cleaning theOutsideofYourVehicleonpage5-89. When ﬁlling the tank do not overﬁll by squeezing in much more fuel after the pump shuts off. While refueling, place the fuel cap in the holder provided. To remove the fuel cap, turn it slowly to the left (counterclockwise). 5-8 When you put the fuel cap back on, turn it to the right (clockwise) until you hear a clicking sound. Make sure you fully install the cap. The diagnostic system can determine if the fuel cap has been left off or improperly installed. This would allow fuel to evaporate into the atmosphere. See MalfunctionIndicatorLampon page3-33. {CAUTION: If a ﬁre starts while you are refueling, do not remove the nozzle. Shut off the ﬂow of fuel by shutting off the pump or by notifying the station attendant. Leave the area immediately. Notice: If you need a new fuel cap, be sure to get the right type. Your dealer can get one for you. If you get the wrong type, it may not ﬁt properly. This may cause your malfunction indicator lamp to light and may damage your fuel tank and emissions system. See MalfunctionIndicatorLampon page3-33. Filling a Portable Fuel Container {CAUTION: Never ﬁll a portable fuel container while it is in your vehicle. Static electricity discharge from the container can ignite the gasoline vapor. You can be badly burned and your vehicle damaged if this occurs. To help avoid injury to you and others: • Dispense gasoline only into approved containers. • Do not ﬁll a container while it is inside a vehicle, in a vehicle’s trunk, pickup bed or on any surface other than the ground. • Bring the ﬁll nozzle in contact with the inside of the ﬁll opening before operating the nozzle. Contact should be maintained until the ﬁlling is complete. • Do not smoke while pumping gasoline. 5-9 Checking Things Under the Hood Hood Release To open the hood, do the following: 1. Pull the release handle located on the driver’s side of the vehicle on the lower portion of the instrument panel. {CAUTION: An electric fan under the hood can start up and injure you even when the engine is not running. Keep hands, clothing and tools away from any underhood electric fan. Do not reach through the grille to release the underhood lever. {CAUTION: Things that burn can get on hot engine parts and start a ﬁre. These include liquids like fuel, oil, coolant, brake ﬂuid, windshield washer and other ﬂuids, and plastic or rubber. You or others could be burned. Be careful not to drop or spill things that will burn onto a hot engine. 5-10 3. Lift the hood, release the hood prop from its retainer and put the hood prop into the slot in the hood. 2. Then go to the front of the vehicle, pull up on the hood, and push the hood release lever to your right. Before closing the hood, be sure all the ﬁller caps are on. Then lift the hood to relieve pressure on the hood prop. Remove the hood prop from the slot in the hood and return the prop to its retainer. Then let the hood down and close it ﬁrmly. 5-11 Engine Compartment Overview When you open the hood on the engine, you’ll see: 5-12 A. Engine Compartment Fuse Block. See “Engine Compartment Fuse Block” under FusesandCircuit Breakers on page5-94. B. Engine Air Cleaner/Filter. See EngineAir Cleaner/Filter on page5-18. C. Battery. See Battery on page5-42. D. Radiator Pressure Cap. See RadiatorPressureCap on page5-28. E. Engine Oil Fill Cap. See EngineOilonpage5-13. F. Automatic Transmission Dipstick. See Automatic Transmission Fluid on page5-20. G. Engine Oil Dipstick. See EngineOilonpage5-13. H. Power Steering Fluid Reservoir. See PowerSteering Fluid on page5-37. I. Brake Master Cylinder Reservoir. See Brakeson page5-39. J. Coolant Recovery Tank. See EngineCoolanton page5-25. K. Windshield Washer Reservoir. See Windshield Washer Fluid on page5-37. Engine Oil If the engine oil pressure light appears on the instrument cluster, it means you need to check your engine oil level right away. For more information, see OilPressureLighton page3-36. You should check your engine oil level regularly; this is an added reminder. 5-13 Checking Engine Oil It is a good idea to check your engine oil every time you get fuel. In order to get an accurate reading, the oil must be warm and the vehicle must be on level ground. The engine oil dipstick handle is a yellow loop. See EngineCompartmentOverviewonpage5-12 for the location of the engine oil dipstick. Turn off the engine and give the oil several minutes to drain back into the oil pan. If you don’t, the oil dipstick might not show the actual level. Pull out the dipstick and clean it with a paper towel or cloth, then push it back in all the way. Remove it again, keeping the tip down, and check the level. When to Add Engine Oil If the oil is at or below the hole at the tip of the dipstick, then you will need to add up to two quarts of oil. But you must use the right kind. This section explains what kind of oil to use. For engine oil crankcase capacity, see CapacitiesandSpeciﬁcationsonpage5-98. Notice: Do not add too much oil. If your engine has so much oil that the oil level gets above the upper mark that shows the proper operating range, your engine could be damaged. See EngineCompartment Overviewonpage5-12 for the location of the engine oil ﬁll cap. Be sure to add enough oil to put the level near the upper hole in the dipstick. Push the dipstick all the way back in when you are through. 5-14 What Kind of Engine Oil to Use Look for two things: • GM6094M Your vehicle’s engine requires oil meeting GM Standard GM6094M. You should look for and use only an oil that meets GM Standard GM6094M. 5-15 Notice: Use only engine oil identiﬁed as meeting GM Standard GM6094M and showing the American Petroleum Institute Certiﬁed For Gasoline Engines starburst symbol. Failure to use the recommended oil can result in engine damage not covered by your warranty. GM Goodwrench® oil meets all the requirements for your vehicle. If you are in an area of extreme cold, where the temperature falls below - 20°F (- 29°C), it is recommended that you use either an SAE 5W-30 synthetic oil or an SAE 0W-30 oil. Both will provide easier cold starting and better protection for your engine at extremely low temperatures. Engine Oil Additives Do not add anything to your oil. The recommended oils with the starburst symbol that meet GM Standard GM6094M are all you will need for good performance and engine protection. • SAE 5W-30 As shown in the viscosity chart, SAE 5W-30 is best for your vehicle. However, if it is going to be 0°F (–18°C) or above and SAE 5W-30 is not available, you may use SAE 10W-30. These numbers on an oil container show its viscosity, or thickness. Do not use other viscosity oils such as SAE 20W-50. Oils meeting these requirements should also have the starburst symbol on the container. This symbol indicates that the oil has been certiﬁed by the American Petroleum Institute (API). You should look for this information on the oil container, and use only those oils that are identiﬁed as meeting GM Standard GM6094M and have the starburst symbol on the front of the oil container. 5-16 What to Do with Used Oil Used engine oil contains certain elements that may be unhealthy for your skin and could even cause cancer. Do not let used oil stay on your skin for very long. Clean your skin and nails with soap and water, or a good hand cleaner. Wash or properly dispose of clothing or rags containing used engine oil. See the manufacturer’s warnings about the use and disposal of oil products. Used oil can be a threat to the environment. If you change your own oil, be sure to drain all the oil from the ﬁlter before disposal. Never dispose of oil by putting it in the trash, pouring it on the ground, into sewers, or into streams or bodies of water. Instead, recycle it by taking it to a place that collects used oil. If you have a problem properly disposing of your used oil, ask your dealer, a service station or a local recycling center for help. When to Change Engine Oil If any one of these is true for you, use the short trip/city maintenance schedule: • Most trips are less than 5 miles (8 km). This is particularly important when outside temperatures are below freezing. • Most trips include extensive idling (such as frequent driving in stop-and-go traffic). • You frequently tow a trailer or use a carrier on top of your vehicle. • The vehicle is used for delivery service, police, taxi or other commercial application. Driving under these conditions causes engine oil to break down sooner. If any one of these is true for your vehicle, then you need to change your oil and ﬁlter every 3,000 miles (5 000 km) or 3 months — whichever occurs ﬁrst. If none of them is true, use the long trip/highway maintenance schedule. Change oil and ﬁlter every 7,500 miles (12 500 km) or 7.5 months — whichever occurs ﬁrst. Driving a vehicle with a fully warmed engine under highway conditions will cause engine oil to break down slower. 5-17 Engine Air Cleaner/Filter See EngineCompartmentOverviewonpage5-12 for location of engine air cleaner/ﬁlter. When to Inspect the Engine Air Cleaner/Filter Inspect the air cleaner/ﬁlter every 15,000 miles (25 000 km) and replace every 30,000 miles (50 000 km). If you are driving in dusty/dirty conditions, inspect the ﬁlter at each engine oil change. How to Inspect the Engine Air Cleaner/Filter To inspect the air cleaner/ﬁlter remove the ﬁlter from the vehicle and lightly shake the ﬁlter to release loose dust and dirt. If the ﬁlter remains caked with dirt, a new ﬁlter is required. To inspect or replace the ﬁlter, do the following: 1. Release the four clips on the cover. 5-18 2. Lift the cover up. {CAUTION: Operating the engine with the air cleaner/ﬁlter off can cause you or others to be burned. The air cleaner not only cleans the air, it helps to stop ﬂame if the engine backﬁres. If it is not there and the engine backﬁres, you could be burned. Do not drive with it off, and be careful working on the engine with the air cleaner/ﬁlter off. 3. Pull out the engine air cleaner/ﬁlter and check or replace it. 4. Reinstall the cover and fasten the clips. Notice: If the air cleaner/ﬁlter is off, a backﬁre can cause a damaging engine ﬁre. And, dirt can easily get into your engine, which will damage it. Always have the air cleaner/ﬁlter in place when you are driving. 5-19 Automatic Transmission Fluid When to Check and Change A good time to check your automatic transmission ﬂuid level is when the engine oil is changed. Change both the ﬂuid and ﬁlter every 15,000 miles (25 000 km) if the vehicle is mainly driven under one or more of these conditions: • In heavy city traffic where the outside temperature regularly reaches 90°F (32°C) or higher. • In hilly or mountainous terrain. • When doing frequent trailer towing. • Uses such as found in taxi, police or delivery service. If you do not use your vehicle under any of these conditions, change the ﬂuid and ﬁlter every 100,000 miles (166 000 km). See Maintenance Requirements on page6-2. How to Check Because this operation can be a little difficult, you may choose to have this done at the dealership service department. If you do it yourself, be sure to follow all the instructions here, or you could get a false reading on the dipstick. Notice: Too much or too little ﬂuid can damage your transmission. Too much can mean that some of the ﬂuid could come out and fall on hot engine part or exhaust system parts, starting a ﬁre. Too little ﬂuid could cause the transmission to overheat. Be sure to get an accurate reading if you check your transmission ﬂuid. Wait at least 30 minutes before checking the transmission ﬂuid level if you have been driving: • When outside temperatures are above 90°F (32°C). • At high speed for quite a while. • In heavy traffic — especially in hot weather. • While pulling a trailer. To get the right reading, the ﬂuid should be at normal operating temperature, which is 180°F to 200°F (82°C to 93°C). 5-20 Get the vehicle warmed up by driving about 15 miles (24 km) when outside temperatures are above 50°F (10°C). If it’s colder than 50°F (10°C), drive the vehicle in DRIVE (D) until the engine temperature gage moves and then remains steady for 10 minutes. A cold ﬂuid check can be made after the vehicle has been sitting for eight hours or more with the engine off, but this is used only as a reference. Let the engine run at idle for ﬁve minutes if outside temperatures are 50°F (10°C) or more. If it’s colder than 50°F (10°C), you may have to idle the engine longer. Should the ﬂuid level be low during this cold check, you must check the ﬂuid hot before adding ﬂuid. Checking the ﬂuid hot will give you a more accurate reading of the ﬂuid level. Checking the Fluid Level Prepare your vehicle as follows: • Park your vehicle on a level place. Keep the engine running. • With the parking brake applied, place the shift lever in PARK (P). • With your foot on the brake pedal, move the shift lever through each gear range, pausing for about three seconds in each range. Then, position the shift lever in PARK (P). • Let the engine run at idle for three minutes or more. Then, without shutting off the engine, follow these steps: The automatic transmission dipstick has a red ring handle located in the rear of the engine compartment toward the center of the vehicle. See EngineCompartment Overviewonpage5-12 for more information on location. 1. Pull out the dipstick and wipe it with a clean rag or paper towel. 2. Push it back in all the way, wait three seconds and then pull it back out again. 5-21 How to Add Fluid Refer to the Maintenance Schedule to determine what kind of transmission ﬂuid to use. See PartD:RecommendedFluidsandLubricantson page6-30. Add ﬂuid only after checking the transmission ﬂuid while it is hot. (A cold check is used only as a reference.) If the ﬂuid level is low, add only enough of the proper ﬂuid to bring the level up to the HOT area for a hot check. It doesn’t take much ﬂuid, generally less than 0.6 pints (0.3 L). Don’toverﬁll. Notice: We recommend you use only ﬂuid labeled DEXRON® -III, because ﬂuid with that label is made especially for your automatic transmission. Damage caused by ﬂuid other than DEXRON® -III is not covered by your new vehicle warranty. • After adding ﬂuid, recheck the ﬂuid level as described under “How to Check.” • When the correct ﬂuid level is obtained, push the dipstick back in all the way. 3. Check both sides of the dipstick, and read the lower level. The ﬂuid level must be in the COLD area for a cold check or in the HOT area for a hot check. If the ﬂuid level is in the acceptable range, push the dipstick back in all the way. 4. 5-22 Manual Transmission Fluid When to Check and Change A good time to have it checked is when the engine oil is changed. Refer to the Maintenance Schedule to determine when to change your transmission ﬂuid. See PartA:ScheduledMaintenanceServicesonpage6-4. How to Check Because this operation can be a little difficult, you may choose to have this done at your Chevrolet dealership service department. If you do it yourself, be sure to follow all the instructions here, or you could get a false reading. Notice: Too much or too little ﬂuid can damage your transmission. Too much can mean that some of the ﬂuid could come out and fall on hot engine part or exhaust system parts, starting a ﬁre. Too little ﬂuid could cause the transmission to overheat. Be sure to get an accurate reading if you check your transmission ﬂuid. Check the ﬂuid level only when your engine is off, the vehicle is parked on a level place and the transmission is cool enough for you to rest your ﬁngers on the transmission case. Then, follow these steps: 1. Remove the ﬁller plug. 2. Check that the lubricant level is up to the bottom of the ﬁller plug hole. 3. If the ﬂuid level is good, install the plug and be sure it is fully seated. If the ﬂuid level is low, add more ﬂuid as described in the next steps. 5-23 When to Check and What to Use Refer to the Maintenance Schedule to determine how often you should check the ﬂuid level in your clutch master cylinder reservoir and for the proper ﬂuid. See PartB:OwnerChecksandServicesonpage6-24 and PartD:RecommendedFluidsandLubricantson page6-30. How to Add Fluid Here’s how to add ﬂuid. Refer to the Maintenance Schedule to determine what kind of ﬂuid to use. See PartD:RecommendedFluidsandLubricantson page6-30. 1. Remove the ﬁller plug. 2. Remove the drain plug, drain the ﬂuid and reinstall the drain plug. 3. Add ﬂuid at the ﬁller plug hole. Add only enough ﬂuid to bring the ﬂuid level up to the bottom of the ﬁller plug hole. 4. Reinstall the ﬁller plug. Be sure the plug is fully seated. Hydraulic Clutch It is not necessary to regularly check clutch ﬂuid unless you suspect there is a leak in the system. Adding ﬂuid won’t correct a leak. A ﬂuid loss in this system could indicate a problem. Have the system inspected and repaired. 5-24 How to Check and Add Fluid You do not need to check the ﬂuid level unless you suspect a clutch problem. To check the ﬂuid level, look at the markings on the reservoir. If the ﬂuid reaches the MAX line, the ﬂuid level is correct. Engine Coolant The following explains your cooling system and how to add coolant when it is low. If you have a problem with engine overheating, see EngineOverheatingon page5-28. A 50/50 mixture of clean, drinkable water and the proper coolant will: • Give freezing protection down to - 33°F (- 36°C) • Give boiling protection up to 258°F (125°C). • Protect against rust and corrosion. • Help keep the proper engine temperature. • Let the warning lights and gages work as they should. What to Use Use a 50/50 mixture of clean,drinkablewater and coolant that meets GM Speciﬁcation 1825-M, which won’t damage aluminum parts. You can also use a recycled coolant conforming to GM Speciﬁcation 1825-M with a complete coolant ﬂush and reﬁll. If you use this coolant mixture, you don’t need to add anything else. {CAUTION: Adding only plain water to your cooling system can be dangerous. Plain water, or some other liquid such as alcohol, can boil before the proper coolant mixture will. Your vehicle’s coolant warning system is set for the proper coolant mixture. With plain water or the wrong mixture, your engine could get too hot but you would not get the overheat warning. Your engine could catch ﬁre and you or others could be burned. Use a 50/50 mixture of clean, drinkable water and the proper coolant. 5-25 Checking Coolant Notice: If you use an improper coolant mixture, your engine could overheat and be badly damaged. The repair cost would not be covered by your warranty. Too much water in the mixture can freeze and crack the engine, radiator, heater core and other parts. If you have to add coolant more than four times a year, have your dealer check your cooling system. Notice: If you use the proper coolant, you do not have to add extra inhibitors or additives which claim to improve the system. These can be harmful. The coolant recovery tank is located toward the front of the engine compartment on the driver’s side of the vehicle. See EngineCompartmentOverviewon page5-12 for more information on location. The vehicle must be on a level surface. When your engine is cold, the coolant level should be at LOW, or a little higher. When your engine is warm, the level should be up to FULL, or a little higher. 5-26 Adding Coolant If you need more coolant, add the proper coolant mixture atthecoolantrecoverytank. {CAUTION: {CAUTION: Turning the radiator pressure cap when the engine and radiator are hot can allow steam and scalding liquids to blow out and burn you badly. With the coolant recovery tank, you will almost never have to add coolant at the radiator. Never turn the radiator pressure cap — even a little — when the engine and radiator are hot. Add coolant mixture at the recovery tank, but be careful not to spill it. You can be burned if you spill coolant on hot engine parts. Coolant contains ethylene glycol, and it will burn if the engine parts are hot enough. Do not spill coolant on a hot engine. Occasionally check the coolant level in the radiator. For information on how to add coolant to the radiator, see Cooling System on page5-31. 5-27 Radiator Pressure Cap Engine Overheating You will ﬁnd a coolant temperature gage on your vehicle’s instrument panel cluster. See EngineCoolant Temperature Gage on page3-32. See EngineCompartmentOverviewonpage5-12 for information on location. Notice: If the pressure cap is not tightly installed, coolant loss and possible engine damage may occur. Be sure the cap is properly and tightly secured. 5-28 If Steam Is Coming From Your Engine {CAUTION: Steam from an overheated engine can burn you badly, even if you just open the hood. Stay away from the engine if you see or hear steam coming from it. Just turn it off and get everyone away from the vehicle until it cools down. Wait until there is no sign of steam or coolant before you open the hood. If you keep driving when your engine is overheated, the liquids in it can catch ﬁre. You or others could be badly burned. Stop your engine if it overheats, and get out of the vehicle until the engine is cool. Notice: If your engine catches ﬁre because you keep driving with no coolant, your vehicle can be badly damaged. The costly repairs would not be covered by your warranty. 5-29 If No Steam Is Coming From Your Engine If you get an engine overheat warning but see or hear no steam, the problem may not be too serious. Sometimes the engine can get a little too hot when you: • Climb a long hill on a hot day. • Stop after high-speed driving. • Idle for long periods in traffic. • Tow a trailer. If you get the overheat warning with no sign of steam, try this for a minute or so: 1. In heavy traffic, let the engine idle in NEUTRAL (N) while stopped. If it is safe to do so, pull off the road, shift to PARK (P) or NEUTRAL (N) and let the engine idle. 2. Turn on your heater to full hot at the highest fan speed and open the window as necessary. If you no longer have the overheat warning, you can drive. Just to be safe, drive slower for about 10 minutes. If the warning doesn’t come back on, you can drive normally. If the warning continues, pull over, stop, and park your vehicle right away. If there’s still no sign of steam, push down the accelerator until the engine speed is about twice as fast as normal idle speed for at least three minutes while you’re parked. If you still have the warning, turnoffthe engineandgeteveryoneoutofthevehicle until it cools down. You may decide not to lift the hood but to get service help right away. 5-30 Cooling System When you decide it’s safe to lift the hood, here’s what you’ll see: {CAUTION: An electric engine cooling fan under the hood can start up even when the engine is not running and can injure you. Keep hands, clothing and tools away from any underhood electric fan. Do not reach through the grill to release the underhood lever. If the coolant inside the coolant recovery tank is boiling, don’t do anything else until it cools down. The vehicle should be parked on a level surface. A. Coolant Recovery Tank B. Radiator Pressure Cap C. Engine Cooling Fan 5-31 {CAUTION: Heater and radiator hoses, and other engine parts, can be very hot. Do not touch them. If you do, you can be burned. Do not run the engine if there is a leak. If you run the engine, it could lose all coolant. That could cause an engine ﬁre, and you could be burned. Get any leak ﬁxed before you drive the vehicle. If there seems to be no leak, start the engine again. The engine cooling fan speed should increase when idle speed is doubled by pushing the accelerator pedal down. If it doesn’t, your vehicle needs service. Turn off the engine. Notice: Engine damage from running your engine without coolant is not covered by your warranty. The coolant level should be at or above FULL. If it isn’t, you may have a leak at the pressure cap or in the radiator hoses, heater hoses, radiator, water pump or somewhere else in the cooling system. 5-32 How to Add Coolant to the Coolant Recovery Tank If you haven’t found a problem yet, but the coolant level isn’t at or above the FULL mark, add a 50/50 mixture of clean,drinkablewater and a proper coolant at the coolant recovery tank. See Engine Coolant on page5-25 for more information about the proper coolant mixture. {CAUTION: Adding only plain water to your cooling system can be dangerous. Plain water, or some other liquid such as alcohol, can boil before the proper coolant mixture will. Your vehicle’s coolant warning system is set for the proper coolant mixture. With plain water or the wrong mixture, your engine could get too hot but you would not get the overheat warning. Your engine could catch ﬁre and you or others could be burned. Use a 50/50 mixture of clean, drinkable water and a proper coolant. Notice: In cold weather, water can freeze and crack the engine, radiator, heater core and other parts. Use the recommended coolant and the proper coolant mixture. {CAUTION: You can be burned if you spill coolant on hot engine parts. Coolant contains ethylene glycol and it will burn if the engine parts are hot enough. Do not spill coolant on a hot engine. 5-33 When the coolant in the coolant recovery tank is at or above the FULL mark, start your vehicle. If the overheat warning continues, there’s one more thing you can try. You can add the proper coolant mixture directly to the radiator, but be sure the cooling system is cool before you do it. {CAUTION: Steam and scalding liquids from a hot cooling system can blow out and burn you badly. They are under pressure, and if you turn the radiator pressure cap — even a little — they can come out at high speed. Never turn the cap when the cooling system, including the radiator pressure cap, is hot. Wait for the cooling system and radiator pressure cap to cool if you ever have to turn the pressure cap. 5-34 How to Add Coolant to the Radiator 1. You can remove the radiator pressure cap when the cooling system, including the radiator pressure cap and upper radiator hose, is no longer hot. Turn the pressure cap slowly counterclockwise until it ﬁrst stops. (Don’t press down while turning the pressure cap.) If you hear a hiss, wait for that to stop. A hiss means there is still some pressure left. 2. Then keep turning the pressure cap, but now push down as you turn it. Remove the pressure cap. 3. Fill the radiator with the proper coolant mixture, up to the base of the ﬁller neck. See EngineCoolant onpage5-25 for more information about the proper coolant mixture. 4. Then ﬁll the coolant recovery tank to the FULL mark. 5-35 5. Put the cap back on the coolant recovery tank, but leave the radiator pressure cap off. 6. Start the engine and let it run until you can feel the upper radiator hose getting hot. Watch out for the engine cooling fan. 7. By this time, the coolant level inside the radiator ﬁller neck may be lower. If the level is lower, add more of the proper coolant mixture through the ﬁller neck until the level reaches the base of the ﬁller neck. 5-36 8. Then replace the pressure cap. At any time during this procedure if coolant begins to ﬂow out of the ﬁller neck, reinstall the pressure cap. Be sure the arrows on the pressure cap line up like this. Power Steering Fluid When to Check Power Steering Fluid It is not necessary to regularly check power steering ﬂuid unless you suspect there is a leak in the system or you hear an unusual noise. A ﬂuid loss in this system could indicate a problem. Have the system inspected and repaired. See EngineCompartmentOverview on page5-12 for reservoir location. How to Check Power Steering Fluid You can check your ﬂuid without taking the cap off. The level should fall between the MIN and MAX marks on the reservoir. What to Use To determine what kind of ﬂuid to use, see PartD: RecommendedFluidsandLubricantsonpage6-30. Notice: When adding power steering ﬂuid or making a complete ﬂuid change, always use the proper ﬂuid. Failure to use the proper ﬂuid can cause leaks and damage hoses and seals. Windshield Washer Fluid What to Use When you need windshield washer ﬂuid, be sure to read the manufacturer’s instructions before use. If you will be operating your vehicle in an area where the temperature may fall below freezing, use a ﬂuid that has sufficient protection against freezing. See Engine CompartmentOverviewonpage5-12 for reservoir location. 5-37 Notice: • When using concentrated washer ﬂuid, follow the manufacturer’s instructions for adding water. • Do not mix water with ready-to-use washer ﬂuid. Water can cause the solution to freeze and damage your washer ﬂuid tank and other parts of the washer system. Also, water does not clean as well as washer ﬂuid. • Fill your washer ﬂuid tank only three-quarters full when it is very cold. This allows for expansion if freezing occurs, which could damage the tank if it is completely full. • Do not use engine coolant (antifreeze) in your windshield washer. It can damage your washer system and paint. Adding Washer Fluid Open the cap with the washer symbol on it. Add washer ﬂuid until the tank is full. 5-38 Brakes Brake Fluid Your brake master cylinder reservoir is ﬁlled with DOT-3 brake ﬂuid. See EngineCompartmentOverviewon page5-12 for the location of the reservoir. There are only two reasons why the brake ﬂuid level in the reservoir might go down. The ﬁrst is that the brake ﬂuid goes down to an acceptable level during normal brake lining wear. When new linings are put in, the ﬂuid level goes back up. The other reason is that ﬂuid is leaking out of the brake system. If it is, you should have your brake system ﬁxed, since a leak means that sooner or later your brakes will not work well, or will not work at all. So, it is not a good idea to “top off” your brake ﬂuid. Adding brake ﬂuid will not correct a leak. If you add ﬂuid when your linings are worn, then you will have too much ﬂuid when you get new brake linings. You should add (or remove) brake ﬂuid, as necessary, only when work is done on the brake hydraulic system. {CAUTION: If you have too much brake ﬂuid, it can spill on the engine. The ﬂuid will burn if the engine is hot enough. You or others could be burned, and your vehicle could be damaged. Add brake ﬂuid only when work is done on the brake hydraulic system. See “Checking Brake Fluid” in this section. Refer to the Maintenance Schedule to determine when to check your brake ﬂuid. See PartC:Periodic Maintenance Inspections on page6-28. 5-39 Checking Brake Fluid You can check the brake ﬂuid without taking off the cap. Just look at the brake ﬂuid reservoir. The ﬂuid level should be above MIN. If it is not, have your brake system checked to see if there is a leak. After work is done on the brake hydraulic system, make sure the level is above the MIN but not over the MAX mark. What to Add When you do need brake ﬂuid, use only DOT-3 brake ﬂuid. Use new brake ﬂuid from a sealed container only. See PartD:RecommendedFluidsandLubricants on page6-30. 5-40 Always clean the brake ﬂuid reservoir cap and the area around the cap before removing it. This will help keep dirt from entering the reservoir. {CAUTION: With the wrong kind of ﬂuid in your brake system, your brakes may not work well, or they may not even work at all. This could cause a crash. Always use the proper brake ﬂuid. Notice: • Using the wrong ﬂuid can badly damage brake system parts. For example, just a few drops of mineral-based oil, such as engine oil, in your brake system can damage brake system parts so badly that they will have to be replaced. Do not let someone put in the wrong kind of ﬂuid. • If you spill brake ﬂuid on your vehicle’s painted surfaces, the paint ﬁnish can be damaged. Be careful not to spill brake ﬂuid on your vehicle. If you do, wash it off immediately. See Appearance Careonpage5-85. Brake Wear Your vehicle has front disc brakes and rear drum brakes. Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads are worn and new pads are needed. The sound may come and go or be heard all the time your vehicle is moving (except when you are pushing on the brake pedal ﬁrmly). {CAUTION: The brake wear warning sound means that soon your brakes will not work well. That could lead to an accident. When you hear the brake wear warning sound, have your vehicle serviced. Notice: Continuing to drive with worn-out brake pads could result in costly brake repair. Some driving conditions or climates may cause a brake squeal when the brakes are ﬁrst applied or lightly applied. This does not mean something is wrong with your brakes. Properly torqued wheel nuts are necessary to help prevent brake pulsation. When tires are rotated, inspect brake pads for wear and evenly tighten wheel nuts in the proper sequence to GM torque speciﬁcations. Your rear drum brakes do not have wear indicators, but if you ever hear a rear brake rubbing noise, have the rear brake linings inspected immediately. Also, the rear brake drums should be removed and inspected each time the tires are removed for rotation or changing. When you have the front brake pads replaced, have the rear brakes inspected, too. Brake linings should always be replaced as complete axle sets. See Brake System Inspection on page6-29. Brake Pedal Travel See your dealer if the brake pedal does not return to normal height, or if there is a rapid increase in pedal travel. This could be a sign of brake trouble. Brake Adjustment Every time you make a brake stop, your disc brakes adjust for wear. 5-41 Replacing Brake System Parts The braking system on a vehicle is complex. Its many parts have to be of top quality and work well together if the vehicle is to have really good braking. Your vehicle was designed and tested with top-quality GM brake parts. When you replace parts of your braking system — for example, when your brake linings wear down and you need new ones put in — be sure you get new approved GM replacement parts. If you do not, your brakes may no longer work properly. For example, if someone puts in brake linings that are wrong for your vehicle, the balance between your front and rear brakes can change — for the worse. The braking performance you have come to expect can change in many other ways if someone puts in the wrong replacement brake parts. Battery Your new vehicle comes with a maintenance free battery. When it is time for a new battery, get one that has the replacement number shown on the original battery’s label. We recommend an ACDelco® battery. See EngineCompartmentOverviewonpage5-12 for battery location. Warning: Battery posts, terminals and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after handling. Vehicle Storage If you are not going to drive your vehicle for 25 days or more, remove the black, negative (- ) cable from the battery. This will help keep your battery from running down. {CAUTION: Batteries have acid that can burn you and gas that can explode. You can be badly hurt if you are not careful. See JumpStartingon page5-43 for tips on working around a battery without getting hurt. Contact your dealer to learn how to prepare your vehicle for longer storage periods. 5-42 Jump Starting If your battery has run down, you may want to use another vehicle and some jumper cables to start your vehicle. Be sure to follow the steps below to do it safely. {CAUTION: Batteries can hurt you. They can be dangerous because: • They contain acid that can burn you. • They contain gas that can explode or • They contain enough electricity to ignite. burn you. If you do not follow these steps exactly, some or all of these things can hurt you. Notice: Ignoring these steps could result in costly damage to your vehicle that would not be covered by your warranty. Trying to start your vehicle by pushing or pulling it will not work, and it could damage your vehicle. 1. Check the other vehicle. It must have a 12-volt battery with a negative ground system. Notice: If the other vehicle’s system is not a 12-volt system with a negative ground, both vehicles can be damaged. Only use vehicles with 12-volt systems with negative grounds to jump start your vehicle. 2. Get the vehicles close enough so the jumper cables can reach, but be sure the vehicles aren’t touching each other. If they are, it could cause a ground connection you don’t want. You wouldn’t be able to start your vehicle, and the bad grounding could damage the electrical systems. To avoid the possibility of the vehicles rolling, set the parking brake ﬁrmly on both vehicles involved in the jump start procedure. Put an automatic transmission in PARK (P) or a manual transmission in NEUTRAL before setting the parking brake. Notice: If you leave your radio or other accessories on during the jump starting procedure, they could be damaged. The repairs would not be covered by your warranty. Always turn off your radio and other accessories when jump starting your vehicle. 3. Turn off the ignition on both vehicles. Unplug unnecessary accessories plugged into the cigarette lighter. Turn off the radio and all lamps that aren’t needed. This will help reduce sparks and help save both batteries. And it could save your radio! 5-43 4. Open the hoods and locate the batteries. Find the positive (+) and negative (- ) terminal locations on each battery. See EngineCompartmentOverview onpage5-12 for more information on battery location. {CAUTION: If your vehicle has air conditioning, the auxiliary electric fan under the hood can start up even when the engine is not running and can injure you. Keep hands, clothing and tools away from any underhood electric fan. {CAUTION: Using a match near a battery can cause battery gas to explode. People have been hurt doing this, and some have been blinded. Use a ﬂashlight if you need more light. Be sure the battery has enough water. You do not need to add water to the battery installed in your new vehicle. But if a battery has ﬁller caps, be sure the right amount of ﬂuid is there. If it is low, add water to take care of that ﬁrst. If you don’t, explosive gas could be present. Battery ﬂuid contains acid that can burn you. Do not get it on you. If you accidentally get it in your eyes or on your skin, ﬂush the place with water and get medical help immediately. 5-44 {CAUTION: Fans or other moving engine parts can injure you badly. Keep your hands away from moving parts once the engine is running. 5. Check that the jumper cables don’t have loose or missing insulation. If they do, you could get a shock. The vehicles could be damaged too. Before you connect the cables, here are some basic things you should know. Positive (+) will go to a positive (+) battery terminal if the vehicle has one. Negative (- ) will go to a heavy, unpainted metal engine part or to a remote negative (- ) terminal if the vehicle has one. Don’t connect positive (+) to negative (- ) or you’ll get a short that would damage the battery and maybe other parts too. And don’t connect the negative (- ) cable to the negative (- ) terminal on the dead battery because this can cause sparks. 6. Connect the red positive (+) cable to the positive (+) terminal of the dead battery. Use a remote positive (+) terminal if the vehicle has one. 7. Don’t let the other end touch metal. Connect it to the positive (+) terminal of the good battery. Use a remote positive (+) terminal if the vehicle has one. 5-45 8. Now connect the black negative (- ) cable to the negative (- ) terminal of the good battery. Use a remote negative (- ) terminal if the vehicle has one. Don’t let the other end touch anything until the next step. The other end of the negative (- ) cable doesn’t go to the dead battery. It goes to a heavy, unpainted metal engine part or to a remote negative (- ) terminal on the vehicle with the dead battery. 9. Connect the other end of the negative (- ) cable at least 18 inches (45 cm) away from the dead battery, but not near engine parts that move. The electrical connection is just as good there, but the chance of sparks getting back to the battery is much less. 10. Now start the vehicle with the good battery and run the engine for a while. 11. Try to start the vehicle with the dead battery. If it won’t start after a few tries, it probably needs service. Notice: If the jumper cables are removed in the wrong order, electrical shorting may occur and damage the vehicle. The repairs would not be covered by your warranty. Remove the jumper cables in the correct order, making sure that the cables do not touch each other or other metal. 5-46 Jumper Cable Removal A. Heavy, Unpainted Metal Engine Part B. Good Battery C. Dead Battery To disconnect the jumper cables from both vehicles, do the following: 1. Disconnect the black negative (- ) cable from the vehicle that had the dead battery. 2. Disconnect the black negative (- ) cable from the vehicle with the good battery. 3. Disconnect the red positive (+) cable from the vehicle with the good battery. 4. Disconnect the red positive (+) cable from the other vehicle. 5-47 Rear Axle When to Check and Change Lubricant Refer to the Maintenance Schedule to determine how often to check the lubricant and when to change it. See PartC:PeriodicMaintenanceInspectionson page6-28 and PartA:ScheduledMaintenanceServices on page6-4. How to Check Lubricant To get an accurate reading, the vehicle should be on a level surface. If the level is below the bottom of the ﬁller plug hole, you’ll need to add some lubricant. 1. Remove the ﬁller plug. 2. Remove the drain plug, drain the lubricant and reinstall the drain plug. 3. Add enough lubricant to raise the level to the bottom of the ﬁller plug hole. 4. Reinstall the ﬁller plug. What to Use Refer to the Maintenance Schedule to determine what kind of lubricant to use. See PartD:Recommended Fluids and Lubricants on page6-30. 5-48 Four-Wheel Drive Most lubricant checks in this section also apply to four-wheel-drive vehicles. However, they have two additional systems that need lubrication. Transfer Case When to Check and Change Lubricant Refer to the Maintenance Schedule to determine how often to check the lubricant and when to change it. See PartA:ScheduledMaintenanceServicesonpage6-4. How to Check Lubricant To get an accurate reading, the vehicle should be on a level surface. If the level is below the bottom of the ﬁller plug hole, you’ll need to add some lubricant. Add enough lubricant to raise the level to the bottom of the ﬁller plug hole. What to Use Refer to the Maintenance Schedule to determine what kind of lubricant to use. See PartD:Recommended Fluids and Lubricants on page6-30. 5-49 Front Axle When to Check and Change Lubricant Refer to the Maintenance Schedule to determine how often to check the lubricant and when to change it. See PartC:PeriodicMaintenanceInspectionsonpage6-28 and PartA:ScheduledMaintenanceServiceson page6-4. How to Check Lubricant To get an accurate reading, the vehicle should be on a level surface. If the level is below the bottom of the ﬁller plug hole, you may need to add some lubricant. 1. Remove the ﬁller plug. 2. Remove the drain plug, drain the lubricant and reinstall the drain plug. 3. When the differential is cold, add enough lubricant to raise the level to 1/2 inch (12 mm) below the ﬁller plug hole. When the differential is at operating temperature (warm), add enough lubricant to raise the level to the bottom of the ﬁller plug hole. 4. Reinstall the ﬁller plug. What to Use Refer to the Maintenance Schedule to determine what kind of lubricant to use. See PartD:Recommended Fluids and Lubricants on page6-30. 5-50 Headlamps Notice: If you use high-intensity bulbs when replacing the headlamp bulbs, you could damage your vehicle. Use only replacement bulbs recommended for your vehicle. See Replacement Bulbsonpage5-55 for more information. Bulb Replacement For the type of bulbs, see ReplacementBulbson page5-55. For any bulb changing procedure not listed in this section, contact your dealer. Halogen Bulbs {CAUTION: Halogen bulbs have pressurized gas inside and can burst if you drop or scratch the bulb. You or others could be injured. Be sure to read and follow the instructions on the bulb package. A. Headlamp B. Front Parking and Turn Signal Lamps 5-51 To replace a headlamp bulb, do the following: 1. Open the hood. 2. Remove the rubber cover and socket from the headlamp. 5-52 3. Release the retainer clip holding the bulb by pressing down and moving the metal retainer away from you. 4. Pull the bulb out of the ﬁxture. 5. Reverse the steps to install a new bulb. Front Turn Signal and Parking Lamps To replace the parking and turn signal bulb, do the following: 1. See “Headlamps” for location. Sidemarker Lamps To replace the sidemarker bulb, do the following: 1. Remove the two screws holding the sidemarker lamp assembly. The assembly should pull away from the vehicle. 2. Locate the turn signal bulb. 3. Turn the bulb socket counterclockwise and pull it out of the lamp housing. 4. Push the bulb in, turn it counterclockwise and pull the bulb straight out of the socket. 5. Reverse the steps to install a new bulb. 2. Turn the socket counterclockwise and pull it out of the housing. 3. Pull the bulb out of the socket. 4. Reverse the steps to install a new bulb. 5-53 Rear Combination Lamps To remove the rear combination bulbs, do the following: A. Turn Signal Lamp B. Back-Up Lamp C. Brake Lamp 5-54 Driver’s Side Passenger’s Side 1. Remove the two screws from the combination lamps. Gently pull the housing away from the vehicle. 2. Turn the bulb socket counterclockwise and pull it out of the lamp housing. 3. Pull the bulb straight out of the socket. 4. Reverse the previous steps to install a new bulb. 5. Reinstall the housing and the screws. Replacement Bulbs Exterior Lamp Back-up Lamp Front Turn Signal and Parking Headlamps (Halogen) Rear Hazard and Turn Signal Rear Parking and Brake Bulb Number 921 1157 NA GM Part No. 91171148 or equivalent 921 GM Part No. 91174349 or equivalent 194 Sidemarker For any bulb not listed here contact your dealer. Tires Your new vehicle comes with high-quality tires made by a leading tire manufacturer. If you ever have questions about your tire warranty and where to obtain service, see your GM Warranty booklet for details. For additional information refer to the tire manufacturer’s booklet included with your vehicle’s Owner’s Manual. {CAUTION: Poorly maintained and improperly used tires are dangerous. • Overloading your tires can cause overheating as a result of too much friction. You could have an air-out and a serious accident. See “Loading Your Vehicle” in the Index. • Underinﬂated tires pose the same danger as overloaded tires. The resulting accident could cause serious injury. Check all tires frequently to maintain the recommended pressure. Tire pressure should be checked when your tires are cold. • Overinﬂated tires are more likely to be cut, punctured or broken by a sudden impact — such as when you hit a pothole. Keep tires at the recommended pressure. • Worn, old tires can cause accidents. If your tread is badly worn, or if your tires have been damaged, replace them. 5-55 Tire Sidewall Labeling Useful information about a tire is molded into the sidewall. The following illustrations are examples of a typical P-Metric and a LT-Metric tire sidewall. 5-56 P-Metric Tire (A) Tire Size Code: The tire size code is a combination of letters and numbers used to deﬁne a particular tire’s width, height, aspect ratio, construction type and service description. See the “Tire Size Code” illustration later in this section for more detail. (B) Tire Performance Criteria Speciﬁcation (TPC Spec): Original equipment tires designed to GM’s speciﬁc tire performance criteria have a TPC speciﬁcation code molded onto the sidewall. GM’s TPC speciﬁcations meet or exceed all federal safety guidelines. (C) Department of Transportation (DOT): The Department of Transportation (DOT) code indicates that the tire is in compliance with the U.S. Department of Transportation Motor Vehicle Safety Standards. (D) Tire Identiﬁcation Number (TIN): The letters and numbers following DOT code are the Tire Identiﬁcation Number (TIN). The TIN shows the manufacturer and plant code, tire size, and date the tire was manufactured. The TIN is molded onto both sides of the tire, although only one side may have the date of manufacture. (E) Tire Ply Material: The type of cord and number of plies in the sidewall and under the tread. (F) Uniform Tire Quality Grading (UTQG): Tire manufacturers are required to grade tires based on three performance factors: treadwear, traction and temperature resistance. For more information, see UniformTireQualityGradingonpage5-68. (G) Maximum Cold Inﬂation Load Limit: Maximum load that can be carried and the maximum pressure needed to support that load. For information on recommended tire pressure see Inﬂation-TirePressure onpage5-63and LoadingYourVehicleonpage4-51. 5-57 (A) Tire Size: The tire size code is a combination of letters and numbers used to deﬁne a particular tire’s width, height, aspect ratio, construction type and service description. See the “Tire Size” illustration later in this section for more detail. (B) Tire Performance Criteria Speciﬁcation (TPC Spec): Original equipment tires designed to GM’s speciﬁc tire performance criteria have a TPC speciﬁcation code molded onto the sidewall. GM’s TPC speciﬁcations meet or exceed all federal safety guidelines. (C) Dual Tire Maximum Load: Maximum load that can be carried and the maximum pressure needed to support that load when used in a dual conﬁguration. For information on recommended tire pressure see Inﬂation-TirePressureonpage5-63 and LoadingYour Vehicle on page4-51. (D) Department of Transportation (DOT): The Department of Transportation (DOT) code indicates that the tire is in compliance with the U.S. Department of Transportation Motor Vehicle Safety Standards. (E) Tire Identiﬁcation Number (TIN): The letters and numbers following DOT code are the Tire Identiﬁcation Number (TIN). The TIN shows the manufacturer and plant code, tire size, and date the tire was manufactured. The TIN is molded onto both sides of the tire, although only one side may have the date of manufacture. LT-Metric Tire 5-58 (F) Tire Ply Material: The type of cord and number of plies in the sidewall and under the tread. (G) Single Tire Maximum Load: Maximum load that can be carried and the maximum pressure needed to support that load when used as a single. For information on recommended tire pressure see Inﬂation-TirePressureonpage5-63 and LoadingYour Vehicle on page4-51. Tire Size The following examples show the different parts of a tire size. Passenger (P-Metric) Tire (A) Passenger (P-Metric) Tire: The United States version of a metric tire sizing system. The letter “P” as the ﬁrst character in the tire size means a passenger vehicle tire engineered to standards set by the U.S. Tire and Rim Association. (B) Tire Width: The three-digit number indicates the tire section width in millimeters from sidewall to sidewall. (C) Aspect Ratio: A two-digit number that indicates the tire height-to-width measurements. For example, if the tire size aspect ratio is “75,” as shown in item “C” of the illustration, it would mean that the tire’s sidewall is 75% as high as it is wide. (D) Construction Code: A letter code is used to indicate the type of ply construction in the tire. The letter “R” means radial ply construction; the letter “D” means diagonal or bias ply construction; and the letter “B” means belted-bias ply construction. (E) Rim Diameter: Diameter of the wheel in inches. (F) Service Description: The service description indicates the load range and speed rating of a tire. The load index can range from 1 to 279. Speed ratings range from “A” to “Z”. The light truck tire size example above shows dual or single tire conﬁgurations. 5-59 (D) Construction Code: A letter code is used to indicate the type of ply construction in the tire. The letter “R” means radial ply construction; the letter “D” means diagonal or bias ply construction; and the letter “B” means belted-bias ply construction. (E) Rim Diameter: Diameter of the wheel in inches. (F) Service Description: The service description indicates the load range and speed rating of a tire. The load index can range from 1 to 279. Speed ratings range from “A” to “Z”. The light truck tire size example above shows dual or single tire conﬁgurations. Tire Terminology and Deﬁnitions Air Pressure: The amount of air inside the tire pressing outward on each square inch of the tire. Air pressure is expressed in pounds per square inch (psi) or kilopascal (kPa). Accessory Weight: This means the combined weight of optional accessories. Some examples of optional accessories are, automatic transmission, power steering, power brakes, power windows, power seats, and air conditioning. Aspect Ratio: The relationship of a tire’s height to its width. Light Truck (LT-Metric) Tire (A) Light Truck (LT-Metric) Tire: The United States version of a metric tire sizing system. The letter “LT” as the ﬁrst two characters in the tire size means a light truck tire engineered to standards set by the U. S. Tire and Rim Association. (B) Tire Width: The three-digit number indicates the tire section width in millimeters from sidewall to sidewall. (C) Aspect Ratio: A two-digit number that indicates the tire height-to-width measurements. For example, if the tire size aspect ratio is “75,” as shown in item “C” of the illustration, it would mean that the tire’s sidewall is 75% as high as it is wide. 5-60 Belt: A rubber coated layer of cords that is located between the plies and the tread. Cords may be made from steel or other reinforcing materials. Bead: The tire bead contains steel wires wrapped by steel cords that hold the tire onto the rim. Bias Ply Tire: A pneumatic tire in which the plies are laid at alternate angles less than 90 degrees to the centerline of the tread. Cold Inﬂation Pressure: The amount of air pressure in a tire, measured in pounds per square inch (psi) or kilopascals (kPa) before a tire has built up heat from driving. See Inﬂation-TirePressureonpage5-63. Curb Weight: This means the weight of a motor vehicle with standard and optional equipment including the maximum capacity of fuel, oil and coolant, but without passengers and cargo. DOT Markings: A code molded into the sidewall of a tire signifying that the tire is in compliance with the U.S. Department of Transportation motor vehicle safety standards. The DOT code includes the Tire Identiﬁcation Number (TIN), an alphanumeric designator which can also identify the tire manufacturer, production plant, brand and date of production. GVWR: Gross Vehicle Weight Rating, see Loading Your Vehicle on page4-51. GAWR FRT: Gross Axle Weight Rating for the front axle, see Loading Your Vehicle on page4-51. GAWR RR: Gross Axle Weight Rating for the rear axle, see Loading Your Vehicle on page4-51. Intended Outboard Sidewall: The side of an asymmetrical tire, that must always face outward when mounted on a vehicle. Kilopascal (kPa): The metric unit for air pressure. There are 6.9 kPa’s to one psi. Light Truck (LT-Metric) Tire: A tire used on light duty trucks and some multipurpose passenger vehicles. Load Index: An assigned number ranging from 1 to 279 that corresponds to the load carrying capacity of a tire. Maximum Inﬂation Pressure: The maximum air pressure to which a cold tire may be inﬂated. The maximum air pressure is molded onto the sidewall. Maximum Load Rating: The load rating for a tire at the maximum permissible inﬂation pressure for that tire. Maximum Loaded Vehicle Weight: The sum of curb weight; accessory weight; vehicle capacity weight; and production options weight. 5-61 Normal Occupant Weight: The number of occupants a vehicle is designed to seat multiplied by 150 pounds (68 kg). See LoadingYourVehicleonpage4-51. Speed Rating: An alphanumeric code assigned to a tire indicating the maximum speed at which a tire can operate. Occupant Distribution: Designated seating positions. Outward Facing Sidewall: The side of a asymmetrical tire that has a particular side that faces outward when mounted on a vehicle. The side of the tire that contains a whitewall, bears white lettering or bears manufacturer, brand and or model name molding that is higher or deeper than the same moldings on the other sidewall of the tire. Passenger (P-Metric) Tire: A tire used on passenger cars and some light duty trucks and multipurpose vehicles. Recommended Inﬂation Pressure: Vehicle manufacturer’s recommended tire inﬂation pressure and shown on the tire placard. See Inﬂation-TirePressure onpage5-63 and LoadingYourVehicleonpage4-51. Radial Ply tire: A pneumatic tire in which the ply cords that extend to the beads are laid at 90 degrees to the centerline of the tread. Rim: A metal support for a tire and upon which the tire beads are seated. Sidewall: The portion of a tire between the tread and the bead. 5-62 Traction: The friction between the tire and the road surface. The amount of grip provided. Tread: The portion of a tire that comes into contact with the road. Treadwear Indicators: Narrow bands, sometimes called “wear bars,” that show across the tread of a tire when only 2/32 inch of tread remains. See WhenIt Is Time for New Tires on page5-66. UTQGS: Uniform Tire Quality Grading Standards, a tire information system that provides consumers with ratings for a tire’s traction, temperature and treadwear. Ratings are determined by tire manufacturers using government testing procedures. The ratings are molded into the sidewall of the tire. See UniformTireQuality Grading on page5-68. Vehicle Capacity Weight: The number of designated seating positions multiplied by 150 lbs. (68 kg) plus the rated cargo load. See LoadingYourVehicle on page4-51. Vehicle Maximum Load on the Tire: Load on an individual tire due to curb weight, accessory weight, occupant weight and cargo weight. If your tires have too much air (overinﬂation), you can get the following: • Unusual wear • Bad handling • Rough ride • Needless damage from road hazards When to Check Check your tires once a month or more. Also, check the tire pressure of the spare tire. Vehicle Placard: A label permanently attached to a vehicle showing the original equipment tire size and recommended inﬂation pressure. See LoadingYour Vehicle on page4-51. Inﬂation - Tire Pressure The tire and loading information label, shows the correct inﬂation pressures for your tires when they’re cold. “Cold” means your vehicle has been sitting for at least three hours or driven no more than 1 mile (1.6 km). See LoadingYourVehicleonpage4-51, for the location of your vehicle’s tire and loading information label. Notice: Don’t let anyone tell you that underinﬂation or overinﬂation is all right. It’s not. If your tires don’t have enough air (underinﬂation), you can get the following: • Too much ﬂexing • Too much heat • Tire overloading • Bad wear • Bad handling • Bad fuel economy 5-63 Tire Inspection and Rotation Tires should be rotated every 5,000 to 8,000 miles (8 000 to 13 000 km). Any time you notice unusual wear, rotate your tires as soon as possible and check wheel alignment. Also check for damaged tires or wheels. See WhenItIsTime forNewTiresonpage5-66 and WheelReplacement on page5-70 for more information. The purpose of regular rotation is to achieve more uniform wear for all tires on the vehicle. The ﬁrst rotation is the most important. See PartA:Scheduled Maintenance Services on page6-4. How to Check Use a good quality pocket-type gage to check tire pressure. You can’t tell if your tires are properly inﬂated simply by looking at them. Radial tires may look properly inﬂated even when they’re underinﬂated. Check the tire’s inﬂation pressure when the tires are cold. cold means your vehicle has been sitting for at least three hours or driven no more than 1 mile (1.6 km). Remove the valve cap from the tire valve stem. Press the tire gage ﬁrmly onto the valve to get a pressure measurement. If the cold tire inﬂation pressure matches the recommended pressure on the tire and loading information label, no further adjustment is necessary. If the pressure is low, add air until you reach the recommended amount. If you overﬁll the tire, release air by pushing on the metal stem in the center of the tire valve. Recheck the tire pressure with the tire gage. Be sure to put the valve caps back on the valve stems. They help prevent leaks by keeping out dirt and moisture. 5-64 When rotating your tires, always use one of the correct rotation patterns shown here. After the tires have been rotated, adjust the front and rear inﬂation pressures as shown on the tire and loading information label. See LoadingYourVehicleon page4-51, for information on the tire and loading information label and its location on your vehicle. Make certain that all wheel nuts are properly tightened. See “Wheel Nut Torque” under Capacities and Speciﬁcations on page5-98. {CAUTION: Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after a time. The wheel could come off and cause an accident. When you change a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle. In an emergency, you can use a cloth or a paper towel to do this; but be sure to use a scraper or wire brush later, if you need to, to get all the rust or dirt off. See “Changing a Flat Tire” in the Index. 5-65 You need a new tire if any of the following statements are true: • You can see the indicators at three or more places around the tire. • You can see cord or fabric showing through the tire’s rubber. • The tread or sidewall is cracked, cut or snagged deep enough to show cord or fabric. • The tire has a bump, bulge or split. • The tire has a puncture, cut or other damage that can’t be repaired well because of the size or location of the damage. When It Is Time for New Tires One way to tell when it’s time for new tires is to check the treadwear indicators, which will appear when your tires have only 1/16 inch (1.6 mm) or less of tread remaining. 5-66 Buying New Tires To ﬁnd out what kind and size of tires you need, look at the Tire and Loading Information label. For information about this label and where to ﬁnd it, see Loading Your Vehicle on page4-51. The tires installed on your vehicle when it was new had a Tire Performance Criteria Speciﬁcation (TPC Spec) number on each tire’s sidewall. When you get new tires, GM recommends that you get tires with that same TPC Spec number. That way your vehicle will continue to have tires that are designed to give proper endurance, handling, speed rating, load range, traction, ride, tire pressure monitoring system performance and other things during normal service on your vehicle. If your tires have an all-season tread design, the TPC number will be followed by an “MS” (for mud and snow). If you ever replace your tires with those not having a TPC Spec number, make sure they are the same size, load range, speed rating and construction type (bias, bias-belted or radial) as your original tires. {CAUTION: Mixing tires could cause you to lose control while driving. If you mix tires of different sizes or types (radial and bias-belted tires), the vehicle may not handle properly, and you could have a crash. Using tires of different sizes may also cause damage to your vehicle. Be sure to use the same size and type tires on all wheels. {CAUTION: If you use bias-ply tires on your vehicle, the wheel rim ﬂanges could develop cracks after many miles of driving. A tire and/or wheel could fail suddenly, causing a crash. Use only radial-ply tires with the wheels on your vehicle. 5-67 Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: Treadwear 200 Traction AA Temperature A The following information relates to the system developed by the United States National Highway Traffic Safety Administration, which grades tires by treadwear, traction and temperature performance. (This applies only to vehicles sold in the United States.) The grades are molded on the sidewalls of most passenger car tires. The Uniform Tire Quality Grading system does not apply to deep tread, winter-type snow tires, space-saver or temporary use spare tires, tires with nominal rim diameters of 10 to 12 inches (25 to 30 cm), or to some limited-production tires. While the tires available on General Motors passenger cars and light trucks may vary with respect to these grades, they must also conform to federal safety requirements and additional General Motors Tire Performance Criteria (TPC) standards. Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a speciﬁed government test course. For example, a tire graded 150 would wear one and a half (1.5) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart signiﬁcantly from the norm due to variations in driving habits, service practices and differences in road characteristics and climate. Traction – AA, A, B, C The traction grades, from highest to lowest, are AA, A, B, and C. Those grades represent the tire’s ability to stop on wet pavement as measured under controlled conditions on speciﬁed government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance. Warning: The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics. 5-68 Wheel Alignment and Tire Balance The wheels on your vehicle were aligned and balanced carefully at the factory to give you the longest tire life and best overall performance. Scheduled wheel alignment and wheel balancing are not needed. However, if you notice unusual tire wear or your vehicle pulling one way or the other, the alignment may need to be reset. If you notice your vehicle vibrating when driving on a smooth road, your wheels may need to be rebalanced. Temperature – A, B, C The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a speciﬁed indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law. Warning: The temperature grade for this tire is established for a tire that is properly inﬂated and not overloaded. Excessive speed, underinﬂation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure. 5-69 Wheel Replacement Replace any wheel that is bent, cracked or badly rusted or corroded. If wheel nuts keep coming loose, the wheel, wheel bolts and wheel nuts should be replaced. If the wheel leaks air, replace it (except some aluminum wheels, which can sometimes be repaired). See your dealer if any of these conditions exist. Your dealer will know the kind of wheel you need. Each new wheel should have the same load-carrying capacity, diameter, width, offset and be mounted the same way as the one it replaces. If you need to replace any of your wheels, wheel bolts or wheel nuts, replace them only with new GM original equipment parts. This way, you will be sure to have the right wheel, wheel bolts and wheel nuts for your vehicle. {CAUTION: Using the wrong replacement wheels, wheel bolts or wheel nuts on your vehicle can be dangerous. It could affect the braking and handling of your vehicle, make your tires lose air and make you lose control. You could have a collision in which you or others could be injured. Always use the correct wheel, wheel bolts and wheel nuts for replacement. Notice: The wrong wheel can also cause problems with bearing life, brake cooling, speedometer or odometer calibration, headlamp aim, bumper height, vehicle ground clearance and tire or tire chain clearance to the body and chassis. See ChangingaFlatTireonpage5-72 for more information. 5-70 Used Replacement Wheels {CAUTION: Putting a used wheel on your vehicle is dangerous. You can’t know how it’s been used or how far it’s been driven. It could fail suddenly and cause a crash. If you have to replace a wheel, use a new GM original equipment wheel. Tire Chains Notice: Use tire chains only where legal and only when you must. Use only SAE Class “S” type chains that are the proper size for your tires. Install them on the tires of the drive axle (four-wheel-drive vehicles can use chains on both axles). Tighten them as tightly as possible with the ends securely fastened. Drive slowly and follow the chain manufacturer’s instructions. If you can hear the chains contacting your vehicle, stop and retighten them. If the contact continues, slow down until it stops. Driving too fast or spinning the wheels with chains on will damage your vehicle. 5-71 If a Tire Goes Flat It’s unusual for a tire to “blowout” while you’re driving, especially if you maintain your tires properly. If air goes out of a tire, it’s much more likely to leak out slowly. But if you should ever have a “blowout,” here are a few tips about what to expect and what to do: If a front tire fails, the ﬂat tire will create a drag that pulls the vehicle toward that side. Take your foot off the accelerator pedal and grip the steering wheel ﬁrmly. Steer to maintain lane position, and then gently brake to a stop well out of the traffic lane. A rear blowout, particularly on a curve, acts much like a skid and may require the same correction you’d use in a skid. In any rear blowout, remove your foot from the accelerator pedal. Get the vehicle under control by steering the way you want the vehicle to go. It may be very bumpy and noisy, but you can still steer. Gently brake to a stop, well off the road if possible. {CAUTION: Lifting a vehicle and getting under it to do maintenance or repairs is dangerous without the appropriate safety equipment and training. The jack provided with your vehicle is designed only for changing a ﬂat tire. If it is used for anything else, you or others could be badly injured or killed if the vehicle slips off the jack. Use the jack provided with your vehicle only for changing a ﬂat tire. If a tire goes ﬂat, the next part shows how to use your jacking equipment to change a ﬂat tire safely. Changing a Flat Tire If a tire goes ﬂat, avoid further tire and wheel damage by driving slowly to a level place. Turn on your hazard warning ﬂashers. 5-72 {CAUTION: CAUTION: (Continued) To be even more certain the vehicle won’t move, you can put blocks at the front and rear of the tire farthest away from the one being changed. That would be the tire on the other side, at the opposite end of the vehicle. Changing a tire can be dangerous. The vehicle can slip off the jack and roll over or fall on you or other people. You and they could be badly injured or even killed. Find a level place to change your tire. To help prevent the vehicle from moving: 1. Set the parking brake ﬁrmly. 2. Put an automatic transmission shift lever in PARK (P), or shift a manual transmission to FIRST (1) or REVERSE (R). 3. If you have a four-wheel-drive vehicle, be sure the transfer case is in a drive gear — not in NEUTRAL. 4. Turn off the engine and do not restart while the vehicle is raised. 5. Do not allow passengers to remain in the vehicle. CAUTION: (Continued) 5-73 The following steps will tell you how to use the jack and change a tire. Removing the Spare Tire and Tools 2. Turn the jack screw to remove the jack from the clamps. If the screw is too tight, use the jack handle to loosen it. The jack, wheel wrench and jack handle are stowed in the rear left corner of the luggage compartment. 1. To open the jacking tool storage compartment, turn the knob counterclockwise. Open the cover two inches and pull the entire cover towards the front of the vehicle. 5-74 The tools you’ll be using include the jack (A), jack handle (B) and wheel wrench (C). The spare tire is mounted on your tailgate. Your vehicle may be equipped with either a soft, vinyl cover or a hard cover. Hard Cover 3. To remove the hard cover from the spare tire, insert your key into the wheel lock and pull the wheel lock off. 5-75 4. Using the wheel wrench, remove the wheel cover nut. Gently pry the spare tire cover off the wheel. Vinyl Cover 5. If your vehicle is equipped with a vinyl cover, unzip the cover to ﬁnd the wheel lock. Insert the key into the wheel lock and pull it off. 6. Using the wheel wrench, remove the wheel nut under the lock. 5-76 Removing the Flat Tire and Installing the Spare Tire 7. Remove the remaining wheel nuts with the wheel wrench. 8. Remove the spare tire from the mounting bracket and place it near your ﬂat tire. 1. If your vehicle has wheel nut caps, remove them by turning the wheel wrench counterclockwise. 5-77 2. Using the wheel wrench, loosen all the wheel nuts but don’t remove them yet. Front Wheel Location 5-78 Rear Wheel Location 3. Under the vehicle near each wheel, there are knobs in the vehicle’s frame. Raise the jack two inches (51 mm) before positioning the jack. Raise the jack lift head until it ﬁts ﬁrmly onto the knobs nearest to the ﬂat tire. {CAUTION: Getting under a vehicle when it is jacked up is dangerous. If the vehicle slips off the jack you could be badly injured or killed. Never get under a vehicle when it is supported only by a jack. {CAUTION: Raising your vehicle with the jack improperly positioned can cause personal injury and damage to the vehicle. If you try to use the jack when it hasn’t been raised at least two inches (51 mm), the jack may not hold up the vehicle, and you or others could be injured. To help avoid personal injury and vehicle damage, be sure to open the jack at least two inches (51 mm) before you ﬁt the lift head into the proper location. 5-79 5. Remove all the wheel nuts and take off the ﬂat tire. 4. Raise the vehicle by turning the jack handle clockwise. Raise the vehicle far enough off the ground so there is enough room for the spare tire to ﬁt underneath the wheel well. 5-80 6. Remove any rust or dirt from the wheel bolts, mounting surfaces and spare wheel.

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2004 Chevrolet Tracker Owners Manual