2011 Chevrolet Suburban Owners Manual

system can calculate the next engine oil change. Always reset the engine oil life to 100% after every oil change. It will not reset itself. To reset the system on most vehicles: 1. Display the OIL LIFE

REMAINING on the DIC. If the vehicle does not have DIC buttons, the vehicle must be in P (Park) to access this display. See Driver Information Center (DIC) on page 5‑27.

Vehicle Care

10-11

2. Press and hold the SET/RESET

button on the DIC, or the trip odometer reset stem if the vehicle does not have DIC buttons, for more than five seconds. The oil life will change to 100%.

On all vehicles, the Engine Oil Life System can be reset as follows: 1. Turn the ignition to ON/RUN with

the engine off.

2. Fully press the accelerator pedal

slowly three times within five seconds.

3. Display the OIL LIFE

REMAINING on the DIC. If the display shows 100%, the system is reset. See Driver Information Center (DIC) on page 5‑27.

If the vehicle has a CHANGE ENGINE OIL SOON message and it comes back on when the vehicle is started and/or the OIL LIFE REMAINING is near 0%, the engine oil life system has not been reset. Repeat the procedure.

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (12,1)

10-12

Vehicle Care

Automatic Transmission Fluid

When to Check and Change Automatic Transmission Fluid It is usually not necessary to check the transmission fluid level. The only reason for fluid loss is a transmission leak or overheated transmission. If a small leak is suspected, then use the following checking procedures to check the fluid level. However, if there is a large leak, then it may be necessary to have the vehicle towed to a dealer service department and have it repaired before driving the vehicle further. Notice: Use of the incorrect automatic transmission fluid may damage the vehicle, and the damages may not be covered by the vehicle warranty. Always use the automatic transmission fluid listed in Recommended Fluids and Lubricants on page 11‑7.

Change the fluid and filter at the scheduled maintenance intervals listed in Scheduled Maintenance on page 11‑3. Be sure to use the transmission fluid listed in Recommended Fluids and Lubricants on page 11‑7. How to Check Automatic Transmission Fluid Notice: Too much or too little fluid can damage the transmission. Too much can mean that some of the fluid could come out and fall on hot engine parts or exhaust system parts, starting a fire. Too little fluid could cause the transmission to overheat. Be sure to get an accurate reading if checking the transmission fluid.

Before checking the fluid level, prepare the vehicle as follows: 1. Start the engine and park the

vehicle on a level surface. Keep the engine running.

2. Apply the parking brake and

place the shift lever in P (Park).

3. With your foot on the brake pedal, move the shift lever through each gear range, pausing for about three seconds in each range. Then, move the shift lever back to P (Park).

4. Allow the engine to idle

(500 – 800 rpm) for at least 1 minute. Slowly release the brake pedal.

5. Keep the engine running and

press the Trip/Fuel button or trip odometer reset stem until TRANS TEMP (Transmission Temperature) displays on the Driver Information Center (DIC).

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (13,1)

Vehicle Care

10-13

6. Using the TRANS TEMP

reading, determine and perform the appropriate check procedure. If the TRANS TEMP reading is not within the required temperature ranges, allow the vehicle to cool, or operate the vehicle until the appropriate transmission fluid temperature is reached.

Cold Check Procedure Use this procedure only as a reference to determine if the transmission has enough fluid to be operated safely until a hot check procedure can be made. The hot check procedure is the most accurate method to check the fluid level. Perform the hot check procedure at the first opportunity. Use this cold check procedure to check fluid level when the transmission temperature is between 27°C and 32°C (80°F and 90°F).

1. Locate the transmission dipstick

at the rear of the engine compartment, on the passenger side of the vehicle. See Engine Compartment Overview on page 10‑6 for more information.

2. Flip the handle up, then pull out

3.

the dipstick and wipe it with a clean rag or paper towel. Install the dipstick by pushing it back in all the way; wait three seconds, and then pull it back out again.

4. Check both sides of the dipstick and read the lower level. Repeat the check procedure to verify the reading.

5.

If the fluid level is below the COLD check band, add only enough fluid as necessary to bring the level into the COLD band. It does not take much fluid, generally less than 0.5 L (1 pt). Do not overfill.

6. Perform a hot check at the

7.

first opportunity after the transmission reaches a normal operating temperature between 71°C to 93°C (160°F to 200°F). If the fluid level is in the acceptable range, push the dipstick back in all the way, then flip the handle down to lock the dipstick in place.

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (14,1)

10-14

Vehicle Care

Hot Check Procedure Use this procedure to check the transmission fluid level when the transmission fluid temperature is between 71°C and 93°C (160°F and 200°F). The hot check is the most accurate method to check the fluid level. The hot check should be performed at the first opportunity in order to verify the cold check. The fluid level rises as fluid temperature increases, so it is important to ensure the transmission temperature is within range.

1. Locate the transmission dipstick

at the rear of the engine compartment, on the passenger side of the vehicle. See Engine Compartment Overview on page 10‑6 for more information.

2. Flip the handle up, then pull out

3.

the dipstick and wipe it with a clean rag or paper towel. Install the dipstick by pushing it back in all the way; wait three seconds, and then pull it back out again.

4. Check both sides of the dipstick and read the lower level. Repeat the check procedure to verify the reading.

5. Safe operating level is within the

HOT cross hatch band on the dipstick. If the fluid level is not within the HOT band, and the transmission temperature is between 71°C and 93°C (160°F and 200°F), add or drain fluid as necessary to bring the level into the HOT band. If the fluid level is low, add only enough fluid to bring the level into the HOT band. It does not take much fluid, generally less than 0.5 L (1 pt). Do not overfill. If the fluid level is in the acceptable range, push the dipstick back in all the way, then flip the handle down to lock the dipstick in place.

6.

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (15,1)

Vehicle Care

10-15

Consistency of Readings Always check the fluid level at least twice using the procedure described previously. Consistency (repeatable readings) is important to maintaining proper fluid level. If readings are still inconsistent, contact the dealer.

Engine Air Cleaner/Filter See Engine Compartment Overview on page 10‑6 for the location of the engine air cleaner/filter. Inspect the air cleaner/filter at the scheduled maintenance intervals and replace it at the first oil change after each 80 000 km (50,000 mi) interval. See Scheduled Maintenance on page 11‑3 for more information. If driving on dusty/dirty conditions, inspect the filter at each engine oil change.

How to Inspect the Engine Air Cleaner/Filter To inspect the air cleaner/filter, remove the engine air cleaner/filter from the vehicle by following Steps 1 through 6. When the engine air cleaner/filter is removed, lightly shake it to release loose dust and dirt. If the engine air cleaner/filter remains covered with dirt, a new filter is required. Never use compressed air to clean the filter.

Replacing the Engine Air Cleaner/ Filter 1. Locate the air cleaner/filter

assembly . See Engine Compartment Overview on page 10‑6.

2. Loosen the four screws on the cover of the housing and lift up the cover.

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (16,1)

10-16

Vehicle Care

{ WARNING

Operating the engine with the air cleaner/filter off can cause you or others to be burned. The air cleaner not only cleans the air; it helps to stop flames if the engine backfires. Use caution when working on the engine and do not drive with the air cleaner/filter off.

3. Remove the engine air cleaner/

filter from the housing. Care should be taken to dislodge as little dirt as possible.

4. Clean the engine air cleaner/ filter sealing surfaces and the housing. Inspect or replace the engine air cleaner/filter.

5.

6. Reinstall the cover and tighten

the screws.

Cooling System If the vehicle is a hybrid, see the hybrid supplement for more information. The cooling system allows the engine to maintain the correct working temperature.

5.3 L V8 Engine Shown, 6.0 L V8 Engine Similar

A. Coolant Surge Tank B. Coolant Surge Tank

Pressure Cap

C. Engine Cooling Fan(s)

(Out of View)

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (17,1)

Vehicle Care

10-17

Engine Coolant The cooling system in the vehicle is filled with DEX-COOL engine coolant. This coolant is designed to remain in the vehicle for 5 years or 240 000 km (150,000 mi), whichever occurs first. The following explains the cooling system and how to check and add coolant when it is low. If there is a problem with engine overheating, see Engine Overheating on page 10‑21.

{ WARNING

An electric engine cooling fan under the hood can start up even when the engine is not running and can cause injury. Keep hands, clothing, and tools away from any underhood electric fan.

{ WARNING

Heater and radiator hoses, and other engine parts, can be very hot. Do not touch them. If you do, you can be burned.

(Continued)

WARNING (Continued)

Do not run the engine if there is a leak. If you run the engine, it could lose all coolant. That could cause an engine fire, and you could be burned. Get any leak fixed before you drive the vehicle.

Notice: Using coolant other than DEX-COOL® can cause premature engine, heater core, or radiator corrosion. In addition, the engine coolant could require changing sooner, at 50 000 km (30,000 mi) or 24 months, whichever occurs first. Any repairs would not be covered by the vehicle warranty. Always use DEX-COOL (silicate-free) coolant in the vehicle.

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (18,1)

10-18

Vehicle Care

What to Use

{ WARNING

Adding only plain water or some other liquid to the cooling system can be dangerous. Plain water and other liquids, can boil before the proper coolant mixture will. The coolant warning system is set for the proper coolant mixture. With plain water or the wrong mixture, the engine could get too hot but you would not get the overheat warning. The engine could catch fire and you or others could be burned. Use a 50/50 mixture of clean, drinkable water and DEX-COOL coolant.

Notice: If extra inhibitors and/or additives are used in the vehicle cooling system, the vehicle could be damaged. Use only the proper mixture of the engine coolant listed in this manual for the cooling system. See Recommended Fluids and Lubricants on page 11‑7 for more information. Never dispose of engine coolant by putting it in the trash, pouring it on the ground, or into sewers, streams, or bodies of water. Have the coolant changed by an authorized service center, familiar with legal requirements regarding used coolant disposal. This will help protect the environment and your health.

Use a 50/50 mixture of clean, drinkable water and DEX-COOL coolant. If using this mixture, nothing else needs to be added. This mixture: . Gives freezing protection down

to −37°C (−34°F), outside temperature.

. Gives boiling protection up to

129°C (265°F), engine temperature.

. Protects against rust and

corrosion.

. Will not damage aluminum parts. . Helps keep the proper engine

temperature.

Notice: If an improper coolant mixture is used, the engine could overheat and be badly damaged. The repair cost would not be covered by the vehicle warranty. Too much water in the mixture can freeze and crack the engine, radiator, heater core, and other parts.

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (19,1)

Checking Coolant The vehicle must be on a level surface when checking the coolant level. Check to see if coolant is visible in the coolant surge tank. If the coolant inside the coolant surge tank is boiling, do not do anything else until it cools down. If coolant is visible but the coolant level is not at or above the FULL COLD mark, add a 50/50 mixture of clean, drinkable water and DEX-COOL coolant at the coolant surge tank, but be sure the cooling system is cool before this is done.

The coolant surge tank is located in the engine compartment on the passenger side of the vehicle. See Engine Compartment Overview on page 10‑6 for more information on location. The coolant level should be at or above the FULL COLD mark. If it is not, the vehicle may have a leak in the cooling system.

Vehicle Care

10-19

How to Add Coolant to the Surge Tank

{ WARNING

You can be burned if you spill coolant on hot engine parts. Coolant contains ethylene glycol and it will burn if the engine parts are hot enough. Do not spill coolant on a hot engine.

Notice: This vehicle has a specific coolant fill procedure. Failure to follow this procedure could cause the engine to overheat and be severely damaged.

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (20,1)

10-20

Vehicle Care

{ WARNING

If no coolant is visible in the surge tank, add coolant as follows:

An electric engine cooling fan under the hood can start up even when the engine is not running and can cause injury. Keep hands, clothing, and tools away from any underhood electric fan.

{ WARNING

Steam and scalding liquids from a hot cooling system can blow out and burn you badly. They are under pressure, and if you turn the surge tank pressure cap — even a little — they can come out at high speed. Never turn the cap when the cooling system, including the surge tank pressure cap, is hot. Wait for the cooling system and surge tank pressure cap to cool if you ever have to turn the pressure cap.

1. Remove the coolant surge tank pressure cap when the cooling system, including the coolant surge tank pressure cap and upper radiator hose, is no longer hot. Turn the pressure cap slowly counterclockwise about one full turn. If a hiss is heard, wait for that to stop. A hiss means there is still some pressure left.

2. Keep turning the pressure cap

slowly and remove it.

3. Fill the coolant surge tank with the proper mixture to the FULL COLD mark.

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (21,1)

5. Replace the pressure cap. Be sure the pressure cap is hand-tight and fully seated.

6. Verify coolant level after engine

is shut off and the coolant is cold. If necessary, repeat coolant fill procedure Steps 1 through 6. Notice: If the pressure cap is not tightly installed, coolant loss and possible engine damage may occur. Be sure the cap is properly and tightly secured. Engine Overheating The vehicle has several indicators to warn of engine overheating. There is a coolant temperature gauge on your vehicle's instrument panel. See Engine Coolant Temperature Gauge on page 5‑16. In addition, ENGINE OVERHEATED STOP ENGINE, ENGINE OVERHEATED IDLE ENGINE, and a ENGINE POWER IS REDUCED message comes on in the Driver Information Center (DIC) on the instrument panel. See

Vehicle Care

10-21

Engine Cooling System Messages on page 5‑40 and Engine Power Messages on page 5‑40. If the decision is made not to lift the hood when this warning appears, but instead get service help right away. See Roadside Assistance Program (U.S. and Canada) on page 13‑7 or Roadside Assistance Program (Mexico) on page 13‑9. If the decision is made to lift the hood, make sure the vehicle is parked on a level surface. Then check to see if the engine cooling fans are running. If the engine is overheating, both fans should be running. If they are not, do not continue to run the engine and have the vehicle serviced. Notice: Engine damage from running the engine without coolant is not covered by the vehicle warranty. See Overheated Engine Protection Operating Mode on page 10‑23 for information on driving to a safe place in an emergency.

4. With the coolant surge tank

pressure cap off, start the engine and let it run until the upper radiator hose can be felt getting hot. Watch out for the engine cooling fan. By this time, the coolant level inside the coolant surge tank may be lower. If the level is lower, add more of the proper mixture to the coolant surge tank until the level reaches the FULL COLD mark.

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (22,1)

10-22

Vehicle Care

Notice: If the engine catches fire while driving with no coolant, the vehicle can be badly damaged. The costly repairs would not be covered by the vehicle warranty. See Overheated Engine Protection Operating Mode on page 10‑23 for information on driving to a safe place in an emergency. If Steam Is Coming from the Engine Compartment { WARNING

Steam from an overheated engine can burn you badly, even if you just open the hood. Stay away from the engine if you see or hear (Continued)

WARNING (Continued)

steam coming from it. Turn it off and get everyone away from the vehicle until it cools down. Wait until there is no sign of steam or coolant before you open the hood. If you keep driving when the vehicles engine is overheated, the liquids in it can catch fire. You or others could be badly burned. Stop the engine if it overheats, and get out of the vehicle until the engine is cool. See Overheated Engine Protection Operating Mode on page 10‑23 for information on driving to a safe place in an emergency.

If No Steam Is Coming from the Engine Compartment The ENGINE OVERHEATED STOP ENGINE or the ENGINE OVERHEATED IDLE ENGINE message, along with a low coolant condition, can indicate a serious problem. If an engine overheat warning is displayed but no steam can be seen or heard, the problem may not be too serious. Sometimes the engine can get a little too hot when the vehicle: . Climbs a long hill on a hot day. . Stops after high-speed driving. Idles for long periods in traffic. Tows a trailer. See Trailer Towing on page 9‑77.

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (23,1)

If the overheat warning is displayed with no sign of steam: 1. Turn the air conditioning off. 2. Turn the heater on to the highest

3.

temperature and to the highest fan speed. Open the windows as necessary. In heavy traffic, let the engine idle in N (Neutral) while stopped. If it is safe to do so, pull off the road, shift to P (Park) or N (Neutral) and let the engine idle.

If the temperature overheat gauge is no longer in the overheat zone or an overheat warning no longer displays, the vehicle can be driven. Continue to drive the vehicle slowly for about 10 minutes. Keep a safe vehicle distance from the vehicle in front. If the warning does not come back on, continue to drive normally. If the warning continues, pull over, stop, and park the vehicle right away.

If there is no sign of steam, idle the engine for three minutes while parked. If the warning is still displayed, turn off the engine until it cools down. Also, see “Overheated Engine Protection Operating Mode” later in this section.

Overheated Engine Protection Operating Mode If an overheated engine condition exists and the ENGINE POWER IS REDUCED message is displayed, an overheat protection mode which alternates firing groups of cylinders helps prevent engine damage. In this mode, a loss in power and engine performance will be noticed. This operating mode allows the vehicle to be driven to a safe place in an emergency. Driving extended distances and/or towing a trailer in the overheat protection mode should be avoided.

Vehicle Care

10-23

Notice: After driving in the overheated engine protection operating mode, to avoid engine damage, allow the engine to cool before attempting any repair. The engine oil will be severely degraded. Repair the cause of coolant loss, change the oil and reset the oil life system. See Engine Oil on page 10‑8.

Engine Fan If the vehicle has a clutched engine cooling fan, when the clutch is engaged, the fan spins faster to provide more air to cool the engine. In most everyday driving conditions, the fan is spinning slower and the clutch is not fully engaged. This improves fuel economy and reduces fan noise. Under heavy vehicle loading, trailer towing, and/or high outside temperatures, the fan speed increases as the clutch more fully engages, so an increase in fan noise may be heard. This is normal and should not be mistaken as the

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (24,1)

10-24

Vehicle Care

transmission slipping or making extra shifts. It is merely the cooling system functioning properly. The fan will slow down when additional cooling is not required and the clutch disengages. This fan noise may also be heard when starting the engine. It will go away as the fan clutch partially disengages. If the vehicle has electric cooling fans, the fans may be heard spinning at low speed during most everyday driving. The fans may turn off if no cooling is required. Under heavy vehicle loading, trailer towing, high outside temperatures, or operation of the air conditioning system, the fans may change to high speed and an increase in fan noise may be heard. This is normal and indicates that the cooling system is functioning properly. The fans will change to low speed when additional cooling is no longer required.

Power Steering Fluid If the vehicle is a hybrid, see the hybrid supplement for more information.

See Engine Compartment Overview on page 10‑6 for reservoir location. When to Check Power Steering Fluid It is not necessary to regularly check power steering fluid unless there is a leak suspected in the system or an unusual noise is heard. A fluid loss in this system could indicate a problem. Have the system inspected and repaired.

How to Check Power Steering Fluid To check the power steering fluid: 1. Turn the key off and let the

engine compartment cool down. 2. Wipe the cap and the top of the

reservoir clean.

3. Unscrew the cap and wipe the

dipstick with a clean rag.

4. Replace the cap and completely

tighten it.

5. Remove the cap again and look at the fluid level on the dipstick.

The level should be at the FULL COLD mark. If necessary, add only enough fluid to bring the level up to the mark.

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (25,1)

What to Use To determine what kind of fluid to use, see Recommended Fluids and Lubricants on page 11‑7. Always use the proper fluid. Notice: Use of the incorrect fluid may damage the vehicle and the damages may not be covered by the vehicle's warranty. Always use the correct fluid listed in Recommended Fluids and Lubricants on page 11‑7.

Washer Fluid

What to Use When windshield washer fluid needs to be added, be sure to read the manufacturer's instructions before use. Use a fluid that has sufficient protection against freezing in an area where the temperature may fall below freezing.

Adding Washer Fluid The vehicle has a low washer fluid message on the DIC that comes on when the washer fluid is low. The message is displayed for 15 seconds at the start of each ignition cycle. When the WASHER FLUID LOW ADD FLUID message displays, washer fluid will need to be added to the windshield washer fluid reservoir.

Open the cap with the washer symbol on it. Add washer fluid until the tank is full. See Engine Compartment Overview on page 10‑6 for reservoir location.

Vehicle Care

10-25

Notice

. When using concentrated

washer fluid, follow the manufacturer's instructions for adding water.

. Do not mix water with

ready-to-use washer fluid. Water can cause the solution to freeze and damage the washer fluid tank and other parts of the washer system. Also, water does not clean as well as washer fluid.

. Fill the washer fluid tank only

three-quarters full when it is very cold. This allows for fluid expansion if freezing occurs, which could damage the tank if it is completely full.

. Do not use engine coolant

(antifreeze) in the windshield washer. It can damage the windshield washer system and paint.

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (26,1)

10-26

Vehicle Care

Brakes This vehicle has disc brakes. Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads are worn and new pads are needed. The sound can come and go or be heard all the time the vehicle is moving, except when applying the brake pedal firmly.

{ WARNING

The brake wear warning sound means that soon the brakes will not work well. That could lead to a crash. When the brake wear warning sound is heard, have the vehicle serviced.

Notice: Continuing to drive with worn-out brake pads could result in costly brake repair.

Some driving conditions or climates can cause a brake squeal when the brakes are first applied or lightly applied. This does not mean something is wrong with the brakes. Properly torqued wheel nuts are necessary to help prevent brake pulsation. When tires are rotated, inspect brake pads for wear and evenly tighten wheel nuts in the proper sequence to torque specifications in Capacities and Specifications on page 12‑2. Brake linings should always be replaced as complete axle sets. Brake Pedal Travel See your dealer if the brake pedal does not return to normal height, or if there is a rapid increase in pedal travel. This could be a sign that brake service might be required.

Brake Adjustment Every time the brakes are applied, with or without the vehicle moving, the brakes adjust for wear. Replacing Brake System Parts The braking system on a vehicle is complex. Its many parts have to be of top quality and work well together if the vehicle is to have really good braking. The vehicle was designed and tested with top-quality brake parts. When parts of the braking system are replaced, be sure to get new, approved replacement parts. If this is not done, the brakes might not work properly. For example, installing disc brake pads that are wrong for the vehicle, can change the balance between the front and rear brakes — for the worse. The braking performance expected can change in many other ways if the wrong replacement brake parts are installed.

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (27,1)

Brake Fluid

The brake master cylinder reservoir is filled with DOT 3 brake fluid. See Engine Compartment Overview on page 10‑6 for the location of the reservoir. There are only two reasons why the brake fluid level in the reservoir might go down:

The brake fluid level goes down because of normal brake lining wear. When new linings are installed, the fluid level goes back up.

. A fluid leak in the brake

hydraulic system can also cause a low fluid level. Have the brake hydraulic system fixed, since a leak means that sooner or later the brakes will not work well.

Vehicle Care

10-27

Do not top off the brake fluid. Adding fluid does not correct a leak. If fluid is added when the linings are worn, there will be too much fluid when new brake linings are installed. Add or remove brake fluid, as necessary, only when work is done on the brake hydraulic system.

{ WARNING

Refer to the Maintenance Schedule to determine when to check the brake fluid. See Scheduled Maintenance on page 11‑3. Checking Brake Fluid Check brake fluid by looking at the brake fluid reservoir. See Engine Compartment Overview on page 10‑6.

If too much brake fluid is added, it can spill on the engine and burn, if the engine is hot enough. You or others could be burned, and the vehicle could be damaged. Add brake fluid only when work is done on the brake hydraulic system. See “Checking Brake Fluid” in this section.

When the brake fluid falls to a low level, the brake warning light comes on. See Brake System Warning Light on page 5‑23.

The fluid level should be above MIN. If it is not, have the brake hydraulic system checked to see if there is a leak.

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (28,1)

10-28

Vehicle Care

After work is done on the brake hydraulic system, make sure the level is above the MIN but not over the MAX mark.

What to Add Use only new DOT 3 brake fluid from a sealed container. See Recommended Fluids and Lubricants on page 11‑7. Always clean the brake fluid reservoir cap and the area around the cap before removing it. This helps keep dirt from entering the reservoir.

{ WARNING

With the wrong kind of fluid in the brake hydraulic system, the brakes might not work well. This could cause a crash. Always use the proper brake fluid.

Notice

. Using the wrong fluid

can badly damage brake hydraulic system parts. For example, just a few drops of mineral-based oil, such as engine oil, in the brake hydraulic system can damage brake hydraulic system parts so badly that they will have to be replaced. Do not let someone put in the wrong kind of fluid.

. If brake fluid is spilled on the

vehicle's painted surfaces, the paint finish can be damaged. Be careful not to spill brake fluid on the vehicle. If you do, wash it off immediately.

Battery If the vehicle is a hybrid, see the hybrid supplement for more information.

Refer to the replacement number on the original battery label when a new battery is needed. See Engine Compartment Overview on page 10‑6 for battery location.

{ DANGER

Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after handling.

Vehicle Storage

{ WARNING

Batteries have acid that can burn you and gas that can explode. You can be badly hurt if you are not careful. See Jump Starting on page 10‑83 for tips on working around a battery without getting hurt.

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (29,1)

Infrequent Usage: Remove the black, negative (−) cable from the battery to keep the battery from running down. Extended Storage: Remove the black, negative (−) cable from the battery or use a battery trickle charger.

Four-Wheel Drive

Transfer Case

When to Check Lubricant Refer to Scheduled Maintenance on page 11‑3 to determine when to check the lubricant.

Vehicle Care

10-29

When to Change Lubricant Refer to Scheduled Maintenance on page 11‑3 to determine how often to change the lubricant.

What to Use Refer to Recommended Fluids and Lubricants on page 11‑7 to determine what kind of lubricant to use.

Front Axle

When to Check and Change Lubricant It is not necessary to regularly check front axle fluid unless a leak is suspected, or an unusual noise is heard. A fluid loss could indicate a problem. Have it inspected and repaired.

How to Check Lubricant

Active Transfer Case

A. Fill Plug B. Drain Plug To get an accurate reading, the vehicle should be on a level surface. If the level is below the bottom of the fill plug hole, some lubricant will need to be added. Add enough lubricant to raise the level to the bottom of the fill plug hole. Use care not to overtighten the plug.

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (30,1)

10-30

Vehicle Care

How to Check Lubricant To get an accurate reading, the vehicle should be on a level surface.

1500 Series

A. Fill Plug B. Drain Plug

What to Use Refer to Recommended Fluids and Lubricants on page 11‑7 to determine what kind of lubricant to use.

Rear Axle

When to Check Lubricant It is not necessary to regularly check rear axle fluid unless there is a leak suspected, or an unusual noise is heard. A fluid loss could indicate a problem. Have it inspected and repaired. All axle assemblies are filled by volume of fluid during production. They are not filled to reach a certain level. When checking the fluid level on any axle, variations in the readings can be caused by factory fill differences between the minimum and the maximum fluid volume. Also, if a vehicle has just been driven before checking the fluid level, it may appear lower than

All Except 1500 Series

A. Fill Plug B. Drain Plug . When the differential is cold, add

enough lubricant to raise the level from 0 mm (0 in) to 3.2 mm (1/8 in) below the fill plug hole.

. When the differential is at

operating temperature (warm), add enough lubricant to raise the level to the bottom of the fill plug hole.

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (31,1)

normal because fluid has traveled out along the axle tubes and has not drained back to the sump area. Therefore, a reading taken five minutes after the vehicle has been driven will appear to have a lower fluid level than a vehicle that has been stationary for an hour or two. Remember that the rear axle assembly must be supported to get a true reading. How to Check Lubricant

1500 Series

2500 Series

To get an accurate reading, the vehicle should be on a level surface.

For the 1500 series, the proper level is from 1.0 mm to 19.0 mm (0.04 in to 0.75 in) below the bottom of the fill plug hole, located on the rear axle. Add only enough fluid to reach the proper level. For the 2500 series, the proper level is from 0 mm to 13 mm (0 in to 1/2 in) below the bottom of the

Vehicle Care

10-31

fill plug hole, located at the front of the axle. Add only enough fluid to reach the proper level.

Starter Switch Check

{ WARNING When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured.

1. Before starting this check, be

sure there is enough room around the vehicle.

2. Firmly apply both the parking brake and the regular brake. See Parking Brake on page 9‑51. Do not use the accelerator pedal, and be ready to turn off the engine immediately if it starts.

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (32,1)

10-32

Vehicle Care

3. Try to start the engine in each gear. The vehicle should start only in P (Park) or N (Neutral). If the vehicle starts in any other position, contact your dealer for service.

Automatic Transmission Shift Lock Control Function Check

{ WARNING When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured.

1. Before starting this check, be

sure there is enough room around the vehicle. It should be parked on a level surface.

2. Firmly apply the parking brake.

See Parking Brake on page 9‑51.

Be ready to apply the regular brake immediately if the vehicle begins to move.

3. With the engine off, turn the

ignition on, but do not start the engine. Without applying the regular brake, try to move the shift lever out of P (Park) with normal effort. If the shift lever moves out of P (Park), contact your dealer for service.

Ignition Transmission Lock Check While parked, and with the parking brake set, try to turn the ignition to LOCK/OFF in each shift lever position.

The ignition should turn to LOCK/OFF only when the shift lever is in P (Park). The ignition key should come out only in LOCK/OFF.

Contact your dealer if service is required.

Park Brake and P (Park) Mechanism Check { WARNING

When you are doing this check, the vehicle could begin to move. You or others could be injured and property could be damaged. Make sure there is room in front of the vehicle in case it begins to roll. Be ready to apply the regular brake at once should the vehicle begin to move.

Park on a fairly steep hill, with the vehicle facing downhill. Keeping your foot on the regular brake, set the parking brake.

To check the parking brake's holding ability: With the engine running and the transmission in N (Neutral), slowly remove foot pressure from the regular brake pedal. Do this until the vehicle is held by the parking brake only.

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (33,1)

To check the P (Park) mechanism's holding ability: With the engine running, shift to P (Park). Then release the parking brake followed by the regular brake.

Contact your dealer if service is required.

Wiper Blade Replacement Windshield wiper blades should be inspected for wear or cracking. See Scheduled Maintenance on page 11‑3. Replacement blades come in different types and are removed in different ways. Front Wiper Blade Replacement 1. Pull the windshield wiper arm

connector away from the windshield.

2. Squeeze the grooved areas on each side of the blade, and turn the blade assembly away from the arm connector.

3.

Install the new blade onto the arm connector and make sure the grooved areas are fully set in the locked position.

For the proper type and size, see Maintenance Replacement Parts on page 11‑9.

Vehicle Care

10-33

Rear Wiper Blade Replacement 1. Lift the wiper blade assembly up and out of the park rest position.

2. Pull the wiper blade assembly away from the backglass. The backglass wiper blade will not lock in a vertical position, so care should be used when pulling it away from the vehicle. 3. Turn the wiper blade assembly, and pull it off of the wiper arm. Hold the wiper arm in position and push the blade away from the wiper arm.

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (34,1)

10-34

Vehicle Care

4. Replace the wiper blade. 5. Return the wiper blade assembly

to the park rest position.

Glass Replacement If the windshield or front side glass must be replaced, see your dealer to determine the correct replacement glass.

Headlamp Aiming The vehicle has a visual optical headlamp aiming system. The aim of the headlamps has been preset at the factory and should need no further adjustment. However, if the vehicle is damaged in a crash, the aim of the headlamps may be affected and adjustment may be necessary. If oncoming vehicles flash their high beams at you, this may mean the vertical aim of the headlamps needs to be adjusted. It is recommended that the vehicle be taken to your dealer for service if the headlamps need to be adjusted. It is possible, however, to re-aim the headlamps as described. The vehicle should: . Be placed so the headlamps

are 7.6 m (25 ft) from a light‐colored wall.

. Have all four tires on a level surface which is level all the way to the wall.

. Be placed so it is perpendicular

to the wall.

. Not have any snow, ice, or mud

on it.

. Be fully assembled and all other

work stopped while headlamp aiming is being performed.

. Be loaded with a full tank of fuel

and one person or 75 kg (160 lbs) sitting on the driver seat.

. Have the tires properly inflated. . Have the spare tire in its proper

location in the vehicle.

Headlamp aiming is done with the vehicle's low-beam headlamps. The high-beam headlamps will be correctly aimed if the low-beam headlamps are aimed properly.

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (35,1)

To adjust the vertical aim: 1. Open the hood. See Hood on

page 10‑5

4. At a wall, measure from the

ground upward (A) to the recorded distance from Step 3 and mark it.

5. Draw or tape a horizontal line (B)

on the wall the width of the vehicle at the height of the mark in Step 4.

Notice: Do not cover a headlamp to improve beam cut-off when aiming. Covering a headlamp may cause excessive heat build-up which may cause damage to the headlamp.

2. Locate the aim dot on the lens of

the low‐beam headlamp.

3. Record the distance from the ground to the aim dot on the low‐beam headlamp.

Vehicle Care

10-35

6. Turn on the low-beam

headlamps and place a piece of cardboard or equivalent in front of the headlamp not being adjusted. This allows only the beam of light from the headlamp being adjusted to be seen on the flat surface.

7. Locate the vertical headlamp

aiming screws, which are under the hood near each headlamp assembly. The adjustment screw can be turned with an E8 Torx® socket.

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (36,1)

10-36

Vehicle Care

8. Turn the vertical aiming screw

until the headlamp beam is aimed to the horizontal tape line. Turn it clockwise or counterclockwise to raise or lower the angle of the beam.

9. Make sure that the light from the

headlamp is positioned at the bottom edge of the horizontal tape line. The lamp on the left (A) shows the correct headlamp aim. The lamp on the right (B) shows the incorrect headlamp aim.

10. Repeat Steps 7 through 9 for

the opposite headlamp.

Bulb Replacement For the proper type of replacement bulbs, see Replacement Bulbs on page 10‑38. For any bulb‐changing procedure not listed in this section, contact your dealer.

Halogen Bulbs

{ WARNING

Halogen bulbs have pressurized gas inside and can burst if you drop or scratch the bulb. You or others could be injured. Be sure to read and follow the instructions on the bulb package.

Taillamps, Turn Signal, Stoplamps, and Back-Up Lamps If the vehicle is a hybrid, see the hybrid supplement for the bulb changing procedure.

A. Stoplamp/Taillamp B. Back-up Lamp C. Taillamp/Turn Signal Lamp D. Side Marker Lamp

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (37,1)

4. Turn the bulb socket

counterclockwise to remove it from the taillamp assembly. 5. Pull the old bulb straight out

from the bulb socket.

6. Press a new bulb into the bulb

socket and install the socket into the taillamp assembly by turning it clockwise.

7. Reinstall the taillamp assembly. When reinstalling, make sure to line up the pins on the taillamp assembly with the vehicle. If this is not done, the taillamp assembly will not be able to be installed correctly.

To replace one of these bulbs: 1. Open the liftgate. See Liftgate

(Power) on page 2‑10 or Liftgate (Manual) on page 2‑12.

2. Remove the two screws from

the taillamp assembly.

3. Pull the taillamp assembly rearward disengaging the two outer pins on the taillamp assembly from the vehicle.

Vehicle Care

10-37

License Plate Lamp

1. Remove the two screws holding each of the license plate lamps to the molding that is part of the liftgate.

2. Twist and pull the license plate lamp assembly forward through the molding opening.

3. Remove the bulb socket from

the lamp assembly by turning it counterclockwise.

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (38,1)

10-38

Vehicle Care

4. Pull the bulb straight out of the socket and install the new bulb.

5. Reverse Steps 1 through 3 to

reinstall the license plate lamp.

Replacement Bulbs If the vehicle is a hybrid, see the hybrid supplement for more information.

Exterior Lamp

Back-up Lamp License Plate Lamp Rear Turn Signal Lamp, Taillamp, and Stoplamp Side Marker Lamp

Bulb

Number

7441

W5WLL

3057K

194

For replacement bulbs not listed here, contact your dealer.

Electrical System

Electrical System Overload The vehicle has fuses and circuit breakers to protect against an electrical system overload. When the current electrical load is too heavy, the circuit breaker opens and closes, protecting the circuit until the current load returns to normal or the problem is fixed. This greatly reduces the chance of circuit overload and fire caused by electrical problems. Fuses and circuit breakers protect the following in the vehicle: . Headlamp Wiring . Windshield Wiper Motor . Power Windows and Other

Power Accessories

Replace a bad fuse with a new one of the identical size and rating.

If there is a problem on the road and a fuse needs to be replaced, the same amperage fuse can be borrowed. Choose some feature of the vehicle that is not needed to use and replace it as soon as possible. Headlamp Wiring An electrical overload may cause the lamps to go on and off, or in some cases to remain off. Have the headlamp wiring checked right away if the lamps go on and off or remain off. Windshield Wipers If the wiper motor overheats due to heavy snow or ice, the windshield wipers will stop until the motor cools and will then restart. Although the circuit is protected from electrical overload, overload due to heavy snow or ice may cause wiper linkage damage. Always clear ice and heavy snow from the windshield before using the windshield wipers.

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (39,1)

If the overload is caused by an electrical problem and not snow or ice, be sure to get it fixed.

Fuses and Circuit Breakers If the vehicle is a hybrid, see the hybrid supplement for more information. The wiring circuits in the vehicle are protected from short circuits by a combination of fuses, circuit breakers and fusible thermal links. This greatly reduces the chance of fires caused by electrical problems. Look at the silver-colored band inside the fuse. If the band is broken or melted, replace the fuse. Be sure you replace a bad fuse with a new one of the identical size and rating.

Vehicle Care

10-39

If you ever have a problem on the road and don't have a spare fuse, you can borrow one that has the same amperage. Just pick some feature of your vehicle that you can get along without – like the radio or cigarette lighter – and use its fuse, if it is the correct amperage. Replace it as soon as you can.

Engine Compartment Fuse Block

If the vehicle is a hybrid, see the hybrid supplement for more information. Notice: Spilling liquid on any electrical component on the vehicle may damage it. Always keep the covers on any electrical component. To remove fuses, hold the end of the fuse between your thumb and index finger and pull straight out.

The Engine Compartment Fuse Block is located in the engine compartment, on the driver side of the vehicle. Lift the cover for access to the fuse/relay block.

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (40,1)

10-40

Vehicle Care

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (41,1)

The vehicle may not be equipped with all of the fuses, relays, and features shown.

Fuses

Usage

Right Trailer Stop/ Turn Lamp Electronic Stability Suspension Control, Automatic Level Control Exhaust Left Trailer Stop/ Turn Lamp Engine Controls Engine Control Module, Throttle Control Trailer Brake Controller Front Washer Oxygen Sensors Antilock Brakes System 2

Fuses

10

11

12

13

14

15

16

17

18

19

20

Usage Trailer Back-up Lamps Driver Side Low-Beam Headlamp Engine Control Module (Battery) Fuel Injectors, Ignition Coils (Right Side) Transmission Control Module (Battery) Vehicle Back-up Lamps Passenger Side Low-Beam Headlamp Air Conditioning Compressor Oxygen Sensors Transmission Controls (Ignition) Fuel Pump

Vehicle Care

10-41

Fuses

Usage

21

22

23

24

25

26

27

28
29

30

31

32

Fuel System Control Module Headlamp Washer Rear Windshield Washer Fuel Injectors, Ignition Coils (Left Side) Trailer Park Lamps Driver Side Park Lamps Passenger Side Park Lamps Fog Lamps Horn Passenger Side High-Beam Headlamp Daytime Running Lamps (DRL) (If Equipped) Driver Side High-Beam Headlamp

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (42,1)

10-42

Vehicle Care

Fuses

Usage

Fuses

33

34

35

36

37

38

39

40

41
42

43

44

Daytime Running Lamps 2 (If Equipped) Sunroof Key Ignition System, Theft Deterrent System Windshield Wiper SEO B2 Upfitter Usage (Battery) Electric Adjustable Pedals Climate Controls (Battery) Airbag System (Ignition) Amplifier Audio System Miscellaneous (Ignition), Cruise Control Liftgate Release

45

46

47

48

49

50
51

52

53

54

55

Usage Airbag System (Battery) Instrument Panel Cluster Not Used Auxiliary Climate Control (Ignition) Center High-Mounted Stoplamp (CHMSL) Rear Defogger Heated Mirrors SEO B1 Upfitter Usage (Battery) Cigarette Lighter, Auxiliary Power Outlet Automatic Level Control Compressor Relay Climate Controls (Ignition)

Fuses

56

J-Case Fuses

57

58

59

60

61

62

63

64

65

Usage Engine Control Module, Secondary Fuel Pump (Ignition)

Usage

Cooling Fan 1
Automatic Level Control Compressor Heavy Duty Antilock Braking System Cooling Fan 2
Antilock Brake System 1
Starter Stud 2 (Trailer Brakes) Left Bussed Electrical Center 1
Electric Running Boards

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (43,1)

J-Case Fuses

Usage

66

67

68

69

70

71

72

Heated Windshield Washer System Transfer Case Stud 1 (Trailer Connector Battery Power) Mid-Bussed Electrical Center 1
Climate Control Blower Power Liftgate Module Left Bussed Electrical Center 2

Relays

Usage

FAN HI

FAN LO

Cooling Fan High Speed Cooling Fan Low Speed

Cooling Fan Control

Low-Beam Headlamp

Relays

Usage

Front Fog Lamps

Air Conditioning Compressor Starter

FAN CNTRL HDLP LO/HID FOG LAMP A/C CMPRSR STRTR PWR/TRN Powertrain FUEL PMP PRK LAMP REAR DEFOG RUN/ CRNK

Fuel Pump

Parking Lamps

Rear Defogger

Switched Power

Vehicle Care

10-43

Instrument Panel Fuse Block