2013 Chevrolet Malibu Owners Manual

Electric Parking Brake Light

Service Electric Parking Brake Light

Antilock Brake System (ABS) Warning Light

Instruments and Controls

5-19

Metric

English

This light comes on when the parking brake is applied. If the light continues flashing after the parking brake is released, or while driving, there is a problem with the electric parking brake system or another system. A message may also display in the Driver Information Center (DIC). See Brake System Messages on page 5‑29. If the light does not come on, or remains flashing, see your dealer.

The service electric parking brake light should come on briefly when the vehicle is in ON/RUN. If it does not come on, have it fixed so it will be ready to warn if there is a problem. If this light stays on, there is a problem with a system on the vehicle that is causing the parking brake system to work at a reduced level. The vehicle can still be driven, but should be taken to a dealer as soon as possible. See Parking Brake on page 9‑30. For vehicles with the uplevel or eAssist cluster, this telltale displays in the DIC screen.

For vehicles with the Antilock Brake System (ABS), this light comes on briefly when the engine is started. If it does not, have the vehicle serviced by your dealer. If the system is working normally, the indicator light then goes off. If the ABS light stays on, turn the ignition off. If the light comes on while driving, stop as soon as it is safely possible and turn the ignition off. Then start the engine again to reset the system. If the ABS light stays on, or comes on again while driving, the vehicle needs service. If the regular brake system warning light is not on, the vehicle still has brakes, but not antilock brakes.

Chevrolet Malibu Owner Manual - 2013 - CRC - 10/24/12

Black plate (20,1)

5-20

Instruments and Controls

If the regular brake system warning light is also on, the vehicle does not have antilock brakes and there is a problem with the regular brakes. See Brake System Warning Light on page 5‑18. For vehicles with a Driver Information Center (DIC), see Brake System Messages on page 5‑29 for all brake-related DIC messages.

Lane Departure Warning (LDW) Light

For vehicles with the LDW system, this light briefly comes on amber while starting the vehicle. If it does not, have the vehicle serviced by your dealer. If the system is working normally, the indicator light then turns off.

Traction Off Light

This light also comes on green when the system is switched on and ready to operate. See Lane Departure Warning (LDW) on page 9‑44.

Vehicle Ahead Indicator

For vehicles with the FCA system, this light comes on in the Driver Information Center (DIC) when a vehicle is detected ahead. See Forward Collision Alert (FCA) System on page 9‑38.

This light comes on briefly while starting the engine. If it does not, have the vehicle serviced by your dealer. This light comes on when the Traction Control System (TCS) has been turned off by pressing and releasing the TCS/StabiliTrak button. This light also comes on and the system turns off if there is a problem with the TCS. If the light comes on and stays on for an extended period of time while the system is turned on, the vehicle needs service.

Chevrolet Malibu Owner Manual - 2013 - CRC - 10/24/12

Black plate (21,1)

Instruments and Controls

5-21

See Traction Control System (TCS) on page 9‑33 and StabiliTrak® System on page 9‑34.

StabiliTrak® OFF Light

See Traction Control System (TCS) on page 9‑33 and StabiliTrak® System on page 9‑34 for more information.

Traction Control System (TCS)/StabiliTrak® Light

This light comes on briefly while starting the engine. If it does not, have the vehicle serviced by your dealer. This light comes on when the StabiliTrak system is turned off. If the Traction Control System (TCS) is off, wheel spin is not limited. If StabiliTrak is off, the system does not assist in controlling the vehicle. Turn on the TCS and the StabiliTrak system and the warning light turns off.

The TCS/StabiliTrak light comes on briefly when the engine is started. If the light does not come on, have the vehicle serviced by the dealer. If the system is working normally, the indicator light turns off. If the light is on while certain DIC messages display, this indicates that the TCS and StabiliTrak systems are not working or are disabled.

If the light is on and not flashing, the TCS and potentially the StabiliTrak system have been disabled. Check the DIC messages to determine which feature(s) is no longer functioning and whether it is because of the driver turning off the feature(s), or because the system is not working properly and the vehicle requires service. If the TCS is disabled, wheel spin is not limited. If the StabiliTrak system is disabled, the system does not aid in maintaining directional control of the vehicle. If the indicator/warning light is on and flashing, the TCS or the StabiliTrak system is actively working. Check the DIC messages for details to determine which system is working. If a message appears in the DIC, the system may be limiting wheel spin and aiding in maintaining directional control of the vehicle.

Chevrolet Malibu Owner Manual - 2013 - CRC - 10/24/12

Black plate (22,1)

5-22

Instruments and Controls

For vehicles with an uplevel or eAssist cluster, this light comes on in the Driver information Center (DIC). See StabiliTrak® System on page 9‑34 and Traction Control System (TCS) on page 9‑33. See Ride Control System Messages on page 5‑33 for more information on the messages associated with this light.

Engine Coolant Temperature Warning Light

For eAssist vehicles, this light comes on briefly while starting the vehicle.

If it does not, have the vehicle serviced by the dealer. If the system is working normally, the indicator light goes off. Notice: Driving with the engine coolant temperature warning light on could cause the vehicle to overheat. See Engine Overheating on page 10‑20. The vehicle's engine could be damaged, and it might not be covered by the vehicle warranty. Never drive with the engine coolant temperature warning light on. The engine coolant temperature warning light comes on when the engine has overheated. If this happens, pull over and turn off the engine as soon as possible. See Engine Overheating on page 10‑20.

Tire Pressure Light

For vehicles with the Tire Pressure Monitor System (TPMS), this light comes on briefly when the engine is started. It provides information about tire pressures and the TPMS. For vehicles with an uplevel or eAssist cluster, this telltale displays in the Driver Information Center (DIC) screen.

When the Light Is On Steady This indicates that one or more of the tires are significantly underinflated.

Chevrolet Malibu Owner Manual - 2013 - CRC - 10/24/12

Black plate (23,1)

A DIC tire pressure message may also display. See Tire Messages on page 5‑34. Stop as soon as possible, and inflate the tires to the pressure value shown on the Tire and Loading Information label. See Tire Pressure on page 10‑52.

When the Light Flashes First and Then Is On Steady If the light flashes for about a minute and then stays on, there may be a problem with the TPMS. If the problem is not corrected, the light will come on at every ignition cycle. See Tire Pressure Monitor Operation on page 10‑55.

Engine Oil Pressure Light Notice: Lack of proper engine oil maintenance can damage the engine. Driving with the engine oil engine. The repairs would not be covered by the vehicle warranty. Check the oil level as soon as possible. Add oil if required, but if the oil level is within the

low can also damage the

Instruments and Controls

5-23

operating range and the oil pressure is still low, have the vehicle serviced. Always follow the maintenance schedule for changing engine oil.

Low Fuel Warning Light

The oil pressure light should come on briefly as the engine is started. If it does not come on have the vehicle serviced by your dealer. If the light comes on and stays on, it means that oil is not flowing through the engine properly. The vehicle could be low on oil and might have some other system problem. See your dealer. For vehicles with the uplevel or eAssist cluster, this telltale displays in the Driver Information Center (DIC) screen.

This light, below the fuel gauge, comes on briefly when the engine is started. If it does not come on, have the vehicle serviced by your dealer. If the system is working normally, the indicator light then goes off. This light also comes on when the fuel tank is low on fuel. When fuel is added the light should go off. If it does not, have your vehicle serviced. For vehicles with an uplevel or eAssist cluster, this telltale displays in the Driver Information Center (DIC) screen.

Chevrolet Malibu Owner Manual - 2013 - CRC - 10/24/12

Black plate (24,1)

5-24

Instruments and Controls

Security Light

High-Beam On Light

Lamps On Reminder

The immobilizer light should come on briefly as the engine is started. If it does not come on, have the vehicle serviced by your dealer. If the system is working normally, the indicator light turns off. If the light stays on and the engine does not start, there could be a problem with the theft-deterrent system. See Immobilizer Operation (Key Access) on page 2‑15 or Immobilizer Operation (Keyless Access) on page 2‑16. For vehicles with an uplevel or eAssist cluster, this light displays in the Driver Information Center (DIC) screen.

This light comes on when the high-beam headlamps are in use. See Headlamp High/Low-Beam Changer on page 6‑2.

Front Fog Lamp Light

This light comes on when the exterior lamps are in use. See Exterior Lamp Controls on page 6‑1.

Cruise Control Light

The fog lamp light comes on when the fog lamps are in use. The light goes out when the fog lamps are turned off. See Fog Lamps on page 6‑4.

This light is white whenever the cruise control is on and turns green when the cruise control is active. The light goes out when the cruise control is turned off. See Cruise Control on page 9‑36.

Chevrolet Malibu Owner Manual - 2013 - CRC - 10/24/12

Black plate (25,1)

For vehicles with the uplevel or eAssist cluster, this telltale will be shown in the Driver Information Center (DIC) screen.

Door Ajar Light

This light comes on in the Driver Information Center (DIC) when a door is open or not securely latched. Before driving, check that all doors are properly closed.

Instruments and Controls

5-25

Information Displays

Center Stack Display Infotainment and vehicle personalization information displays in the center stack screen. See:

The navigation system manual and Infotainment on page 7‑1.

. Vehicle Personalization on

page 5‑36.

The center stack controls only need a light touch to operate and work best with bare hands. The controls will work with most gloves although they may take longer to respond. Use the finger pad rather than the finger tip to minimize response time. If the controls are not responding, remove the gloves.

Driver Information Center (DIC) The DIC displays information about the vehicle. It also displays warning messages if a system problem is detected. See Vehicle Messages on page 5‑29. All messages appear in the DIC display in the center of the instrument cluster. The vehicle may also have features that can be customized through the controls on the radio. See Vehicle Personalization on page 5‑36. DIC Operation and Displays The DIC has different displays, which can be accessed by using the DIC buttons on the turn signal lever to the left of the steering wheel. The DIC displays trip, fuel, vehicle system information, and warning messages if a system problem is detected.

Chevrolet Malibu Owner Manual - 2013 - CRC - 10/24/12

Black plate (26,1)

5-26

Instruments and Controls

DIC Buttons

1. SET/CLR: Press to set or clear

the menu item displayed.

2. w / x (Thumbwheel): Use to

scroll through the menus.

3. MENU: Press to display the Trip/

Fuel menu and the Vehicle Information menu. This button is also used to return to or exit the last screen displayed on the DIC.

Trip/Fuel Menu Items Press MENU on the turn signal lever until Trip/Fuel Menu is displayed. Use w / x to scroll through the menu items. The following is the list of all possible

trip/fuel displays. Some of the items may not be available for your particular vehicle. . Digital Speedometer

Trip 1
Trip 2

. Power Flow (eAssist Only)

Fuel Range

. Average Fuel Economy and

Instantaneous Fuel Economy

. Average Vehicle Speed

Timer

. Navigation . Boost Gauge

Digital Speedometer The speedometer shows how fast the vehicle is moving in either kilometers per hour (km/h) or miles per hour (mph). The speedometer cannot be reset.

Trip 1 and Trip 2
This display shows the current distance traveled, in either kilometers (km) or miles (mi), since the last reset for the trip odometer. The trip odometer can be reset to zero by pressing SET/CLR while the trip odometer display is showing.

Power Flow (eAssist Only) This display shows the operating mode of the eAssist system and the high voltage battery charge level. The animation indicates the direction of energy flow.

Fuel Range This display shows the approximate distance the vehicle can be driven without refueling. The fuel range estimate is based on an average of the vehicle's fuel economy over recent driving history and the amount of fuel remaining in the fuel tank. Fuel range cannot be reset.

Chevrolet Malibu Owner Manual - 2013 - CRC - 10/24/12

Black plate (27,1)

Instruments and Controls

5-27

Average Fuel Economy and Instantaneous Fuel Economy This display shows the approximate average liters per 100 kilometers (L/100 km) or miles per gallon (mpg). This number is calculated based on the number of L/100 km (mpg) recorded since the last time this menu item was reset. The fuel economy can be reset by pressing SET/CLR while the Average Fuel Economy display is showing. The instantaneous fuel economy display shows the current fuel economy in liters per 100 kilometers (L/100 km) or miles per gallon (mpg). This number reflects only the fuel economy that the vehicle has right now and changes frequently as driving conditions change. Unlike average economy, this display cannot be reset.

Average Vehicle Speed This display shows the average speed of the vehicle in kilometers per hour (km/h) or miles per hour (mph). This average is calculated based on the various vehicle speeds recorded since the last reset of this value. The average speed can be reset by pressing SET/CLR while the Average Vehicle Speed display is showing.

Timer This display can be used as a timer. To start the timer, press SET/CLR while Timer is displayed. The display will show the amount of time that has passed since the timer was last reset, not including time the ignition is off. Time will continue to be counted as long as the ignition is on, even if another display is being shown on the DIC. The timer will record up to 99 hours, 59 minutes, and 59 seconds (99:59:59) after which the display will return to zero. To stop the timer, press SET/CLR

briefly while Timer is displayed. To reset the timer to zero, press and hold SET/CLR.

Navigation This display is used for the Turn-by-Turn navigation, if equipped.

Boost Gauge This display, available on some vehicles, is a boost gauge. It shows a visual display of the level of boost. Vehicle Information Menu Items Press MENU on the turn signal lever until Vehicle Information menu is displayed. Use w / x to scroll through the menu items. The following is the list of all possible vehicle information displays. Some of the items may not be available for your particular vehicle. . Display Units Tire Pressure Jump Start (eAssist Only)

Chevrolet Malibu Owner Manual - 2013 - CRC - 10/24/12

Black plate (28,1)

5-28

Instruments and Controls

. Remaining Oil Life . Battery

Display Units Move w / x to switch between metric or US when the Unit display is active. Press SET/CLR to confirm the setting. This will change the displays on the cluster and DIC to either metric or English (US) measurements.

Tire Pressure The display will show a vehicle with the approximate pressures of all four tires. Tire pressure is displayed in either kilopascal (kPa) or pounds per square inch (psi). See Tire Pressure Monitor System on page 10‑54 and Tire Pressure Monitor Operation on page 10‑55.

Jump Start (eAssist Only) This display allows for on-board jump starting of the vehicle. See "Jump Starting (On-board with eAssist Only)" for more information.

Remaining Oil Life This display shows an estimate of the oil's remaining useful life. If Remaining Oil Life 99% is displayed, that means 99% of the current oil life remains. When the remaining oil life is low, the CHANGE ENGINE OIL SOON message will appear on the display. See Engine Oil Messages on page 5‑31. The oil should changed as soon as possible. See Engine Oil on page 10‑11. In addition to the engine oil life system monitoring the oil life, additional maintenance is recommended. See Maintenance Schedule on page 11‑2.

Remember, the Oil Life display must be reset after each oil change. It will not reset itself. Also, be careful not to reset the Oil Life display accidentally at any time other than when the oil has just been changed. It cannot be reset accurately until the next oil change. To reset the engine oil life system, press SET/CLR while the Oil Life display is active. See Engine Oil Life System on page 10‑13.

Battery This display, available on some vehicles, shows the current battery voltage. If the voltage is in the normal range, the value will display. For example, the display may read Battery Voltage 15.0 Volts. The vehicle's charging system regulates voltage based on the state of the battery. The battery voltage can fluctuate while viewing this information on the DIC. This is normal. See Charging System Light on page 5‑15. If there is a problem with the battery charging system, the DIC will display a message.

Chevrolet Malibu Owner Manual - 2013 - CRC - 10/24/12

Black plate (29,1)

Vehicle Messages Messages displayed on the DIC indicate the status of the vehicle or some action that may be needed to correct a condition. Multiple messages may display one after the other. The messages that do not require immediate action can be acknowledged and cleared by pressing SET/CLR. The messages that require immediate action cannot be cleared until that action is performed. All messages should be taken seriously and clearing the messages does not correct the problem. The following are some of the vehicle messages that may be displayed depending on your vehicle content.

Instruments and Controls

5-29

Battery Voltage and Charging Messages

BATTERY SAVER ACTIVE This message displays when the vehicle has detected that the battery voltage is dropping beyond a reasonable point. The battery saver system starts reducing features of the vehicle that may be noticed. At the point that features are disabled, this message displays. Turn off unnecessary accessories to allow the battery to recharge. LOW BATTERY This message is displayed when the battery voltage is low. See Battery on page 10‑25. SERVICE BATTERY CHARGING SYSTEM This message is displayed when there is a fault in the battery charging system. Take the vehicle to your dealer for service.

Brake System Messages

BRAKE FLUID LOW This message is displayed when the brake fluid level is low. See Brake Fluid on page 10‑23. RELEASE PARKING BRAKE This message is displayed if the Electric Parking Brake (EPB) is on while the vehicle is in motion. Release it before you attempt to drive. See Parking Brake on page 9‑30. SERVICE BRAKE ASSIST This message may be displayed when there is a problem with the brake boost assist system. When this message is displayed, the brake boost assist motor might be heard operating and you might notice pulsation in the brake pedal. This is normal under these conditions. Take the vehicle to your dealer for service.

Chevrolet Malibu Owner Manual - 2013 - CRC - 10/24/12

Black plate (30,1)

5-30

Instruments and Controls

SERVICE PARKING BRAKE This message is displayed when there is a problem with the Electric Parking Brake (EPB). See Parking Brake on page 9‑30. Take the vehicle to your dealer. STEP ON BRAKE TO RELEASE PARK BRAKE This message is displayed if you attempt to release the Electric Parking Brake (EPB) without the brake pedal applied. See Parking Brake on page 9‑30.

Compass Messages

CAL This message is displayed when the compass needs to be calibrated. See Compass on page 5‑5. – – Dashes will be displayed if the compass needs service. See your dealer for service.

Cruise Control Messages

CRUISE SET TO XXX This message displays when the cruise control is set and shows the speed it was set to. See Cruise Control on page 9‑36.

Door Ajar Messages

DRIVER DOOR OPEN This message will display when the driver door is open. Close the door completely. HOOD OPEN This message will display when the hood is open. Close the hood completely. LEFT REAR DOOR OPEN This message will display when the driver side rear door is open. Close the door completely.

PASSENGER DOOR OPEN This message will display when the front passenger door is open. Close the door completely. RIGHT REAR DOOR OPEN This message will display when the passenger side rear door is open. Close the door completely. TRUNK OPEN This message will display when the trunk is open. Close the trunk completely.

Engine Cooling System Messages

A/C OFF DUE TO HIGH ENGINE TEMP This message displays when the engine coolant becomes hotter than the normal operating temperature. To avoid added strain on a hot engine, the air conditioning compressor automatically turns off.

Chevrolet Malibu Owner Manual - 2013 - CRC - 10/24/12

Black plate (31,1)

Instruments and Controls

5-31

When the coolant temperature returns to normal, the air conditioning compressor turns back on. You can continue to drive the vehicle. If this message continues to appear, have the system repaired by your dealer as soon as possible to avoid damage to the engine. COOLANT LEVEL LOW ADD COOLANT This message will display if the coolant is low. See Engine Coolant on page 10‑18. ENGINE OVERHEATED — IDLE ENGINE This message displays when the engine coolant temperature is too hot. Stop and allow the vehicle to idle until it cools down.

ENGINE OVERHEATED — STOP ENGINE This message displays and a continuous chime sounds if the engine cooling system reaches unsafe temperatures for operation. Stop and turn off the vehicle as soon as it is safe to do so to avoid severe damage. This message clears when the engine has cooled to a safe operating temperature.

Engine Oil Messages

CHANGE ENGINE OIL SOON This message displays when the engine oil needs to be changed. When the engine oil is changed, be sure to reset the Oil Life System. See Engine Oil Life System on page 10‑13, Driver Information Center (DIC) on page 5‑25, Engine Oil on page 10‑11, and Maintenance Schedule on page 11‑2.

ENGINE OIL HOT, IDLE ENGINE This message displays when the engine oil temperature is too hot. Stop and allow the vehicle to idle until it cools down. OIL PRESSURE LOW— STOP ENGINE This message displays if low oil pressure levels occur. Stop the vehicle as soon as safely possible and do not operate it until the cause of the low oil pressure has been corrected. Check the oil as soon as possible and have the vehicle serviced by your dealer.

Chevrolet Malibu Owner Manual - 2013 - CRC - 10/24/12

Black plate (32,1)

5-32

Instruments and Controls

Engine Power Messages

ENGINE POWER IS REDUCED This message displays when the vehicle's engine power is reduced. Reduced engine power can affect the vehicle's ability to accelerate. If this message is on, but there is no reduction in performance, proceed to your destination. The performance may be reduced the next time the vehicle is driven. The vehicle may be driven at a reduced speed while this message is on, but maximum acceleration and speed may be reduced. Anytime this message stays on, the vehicle should be taken to your dealer for service as soon as possible.

Fuel System Messages

FUEL LEVEL LOW This message displays when the vehicle is low on fuel. Refuel as soon as possible.

TIGHTEN GAS CAP This message displays when the fuel cap is not on tight. Tighten the fuel cap.

Key and Lock Messages

NO REMOTE DETECTED This message displays when the transmitter battery is weak on vehicles with keyless access. See “Starting the Vehicle with a Low Transmitter Battery” under Remote Keyless Entry (RKE) System Operation on page 2‑3. REPLACE BATTERY IN REMOTE KEY This message displays when the battery in the Remote Keyless Entry (RKE) transmitter needs to be replaced. See “Battery Replacement” under Remote Keyless Entry (RKE) System Operation on page 2‑3.

Lamp Messages

AUTOMATIC LIGHT CONTROL ON/OFF This message is displayed when the automatic light control has been turned on or off. See Automatic Headlamp System on page 6‑3. CHECK XXX TURN SIGNAL LAMP When one of the turn signals is out, this message displays to show which bulb needs to be replaced. See Bulb Replacement on page 10‑28 and Replacement Bulbs on page 10‑36. TURN SIGNAL ON This message is displayed if the turn signal has been left on. Turn off the turn signal.

Chevrolet Malibu Owner Manual - 2013 - CRC - 10/24/12

Black plate (33,1)

Object Detection System Messages

LANE DEPARTURE WARNING UNAVAILABLE This message may appear if LDW does not activate due to a temporary condition. PARK ASSIST OFF This message displays when the park assist system has been turned off or when there is a temporary condition causing the system to be disabled. See Ultrasonic Parking Assist on page 9‑40. SERVICE LANE DEPARTURE WARNING This message may appear to indicate that LDW is not working properly. If this message remains on after continued driving, the system needs service. Take your vehicle to your dealer.

Instruments and Controls

5-33

SERVICE PARK ASSIST This message displays if there is a problem with the Ultrasonic Rear Parking Assist (URPA) system. Do not use this system to help you park. See Ultrasonic Parking Assist on page 9‑40 for more information. See your dealer for service.

Ride Control System Messages

SERVICE TRACTION CONTROL This message displays when there is a problem with the Traction Control System (TCS). When this message is displayed, the system will not limit wheel spin. Adjust your driving accordingly. See your dealer for service. SERVICE STABILITRAK This message displays if there is a problem with the StabiliTrak system. If this message appears, try to reset the system. Stop; turn off the engine

for at least 15 seconds; then start the engine again. If this message still comes on, it means there is a problem. See your dealer for service. The vehicle is safe to drive; however, you do not have the benefit of StabiliTrak, so reduce your speed and drive accordingly.

Security Messages

THEFT ATTEMPTED This message displays if the vehicle detects a tamper condition.

Service Vehicle Messages

SERVICE AC SYSTEM This message displays if there is a problem with the air conditioning system. Take the vehicle to your dealer for service. SERVICE POWER STEERING This message displays if there is a problem with the power steering system. Take the vehicle to your dealer for service.

Chevrolet Malibu Owner Manual - 2013 - CRC - 10/24/12

Black plate (34,1)

5-34

Instruments and Controls

SERVICE VEHICLE SOON This message displays if there is a problem with the vehicle. Take the vehicle to your dealer for service.

Starting the Vehicle Messages

JUMP START ACTIVE WAIT TO START This message displays while performing an on-board jump start of the vehicle. See “Jump Starting (On-board with eAssist Only).” JUMP START COMPLETE ATTEMPT START This message displays while performing an on-board jump start of the vehicle. See “Jump Starting (On-board with eAssist Only).”

JUMP START DISABLED SEE OWNERS MANUAL This message displays if there is a problem with the on-board jump start system, or the 12 volt battery is too low to perform an on-board jump start. Try using jumper cables and performing a normal jump start. See “Jump Starting (On-board with eAssist Only).” Take the vehicle to your dealer for service if this message continues to be displayed.

Tire Messages

TIRE PRESSURE LOW ADD AIR TO TIRE On vehicles with the Tire Pressure Monitor System (TPMS), this message displays when the pressure in one or more of the vehicle's tires is low. The low tire pressure warning light will also come on. See Tire Pressure Light on page 5‑22.

If a tire pressure message appears on the DIC, stop as soon as you can. Inflate the tires by adding air until the tire pressure is equal to the values shown on the Tire and Loading Information label. See Tires on page 10‑44, Vehicle Load Limits on page 9‑10, and Tire Pressure on page 10‑52. You can receive more than one tire pressure message at a time. To read the other messages that may have been sent at the same time, press the SET/CLR button. The DIC also shows the tire pressure values. See Driver Information Center (DIC) on page 5‑25. SERVICE TIRE MONITOR SYSTEM This message displays if there is a problem with the Tire Pressure Monitor System (TPMS). See Tire Pressure Monitor Operation on page 10‑55.

Chevrolet Malibu Owner Manual - 2013 - CRC - 10/24/12

Black plate (35,1)

Instruments and Controls

5-35

TRANSMISSION HOT— IDLE ENGINE This message displays and a chime sounds if the transmission fluid in the vehicle gets hot. Driving with the transmission fluid temperature high can cause damage to the vehicle. Stop the vehicle and let it idle to allow the transmission to cool. This message clears when the fluid temperature reaches a safe level.

Vehicle Reminder Messages

ICE POSSIBLE DRIVE WITH CARE This message displays when ice conditions are possible.

Washer Fluid Messages

WASHER FLUID LOW ADD FLUID This message may display when the washer fluid level is low. See Washer Fluid on page 10‑22.

Window Messages

OPEN, THEN CLOSE DRIVER/ PASSENGER WINDOW This message is displayed when the window needs to be reprogrammed. If the vehicle's battery has been recharged or disconnected, you will need to reprogram each front window for the express-up feature to work. See Power Windows on page 2‑19.

TIRE LEARNING ACTIVE This message displays when the system is learning new tires. See Tire Pressure Monitor Operation on page 10‑55.

Transmission Messages

SERVICE TRANSMISSION This message displays if there is a problem with the transmission. See your dealer. SHIFT DENIED This message displays when attempting to use the automatic transmission manual mode to shift to too low or too high of a gear. See Manual Mode on page 9‑28. SHIFT TO PARK This message displays when the transmission needs to be shifted to P (Park). This may appear when attempting to remove the key from the ignition or from the vehicle if the vehicle is not in P (Park).

Chevrolet Malibu Owner Manual - 2013 - CRC - 10/24/12

Black plate (36,1)

5-36

Instruments and Controls

Vehicle Personalization The audio system controls are used to access the personalization menus for customizing vehicle features. CONFIG (Configuration): Press to access the Configuration Settings menu. TUNE/MENU: Turn to scroll through the menus. Press to enter the menus and select the menu items. BACK / : Press to exit or move backward in a menu.

Entering the Personalization Menus 1. Press CONFIG to access the Configuration Settings menu.

2. Turn the TUNE/MENU knob to

highlight Vehicle Settings.

3. Press TUNE/MENU to select the

Vehicle Settings menu.

The following list of menu items will be available: . Climate and Air Quality . Comfort and Convenience

Language Lighting

. Power Door Locks . Remote Locking, Unlocking,

Starting

. Return to Factory Settings Turn the TUNE/MENU knob to highlight the menu. Press TUNE/ MENU to select it. Each of the menus is detailed in the following information. Climate and Air Quality Select the Climate and Air Quality menu and the following may be displayed: . Auto Fan Speed . Remote Start Heated Seats

. Auto Defog . Auto Rear Defog

Auto Fan Speed This will allow you to select the automatic fan speed. It can be adjusted to run lower or higher than normal. Press TUNE/MENU when Auto Fan Speed is highlighted to open the menu. Turn the TUNE/MENU knob to highlight High, Medium, or Low. Press TUNE/MENU to confirm the selection and move back to the last menu.

Remote Start Heated Seats When turned on, this feature will turn the heated seats on when using remote start on cold days. Press TUNE/MENU when Remote Start Heated Seats is highlighted. Turn the TUNE/MENU knob to select On or Off. Press TUNE/ MENU to confirm the selection and move back to the last menu.

Chevrolet Malibu Owner Manual - 2013 - CRC - 10/24/12

Black plate (37,1)

Instruments and Controls

5-37

Auto Defog Only vehicles with dual automatic climate control will have this option. This will allow you to turn the auto defog on or off. Press TUNE/MENU when Auto Defog is highlighted to open the menu. Turn the TUNE/MENU knob to highlight On or Off. Press TUNE/ MENU to confirm the selection and move back to the last menu.

Auto Rear Defog This will allow you to turn the auto rear defog on or off. This feature will automatically turn on the rear window defogger when it is cold outside. Press TUNE/MENU when Auto Rear Defog is highlighted to open the menu. Turn the TUNE/MENU knob to highlight On or Off. Press TUNE/MENU to confirm the selection and move back to the last menu.

Comfort and Convenience Select the Comfort and Convenience menu and the following may be displayed: . Easy Exit Driver Seat . Chime Volume . Reverse Tilt Mirror

Easy Exit Driver Seat When on, this feature will move the driver seat rearward upon turning the ignition off and opening the driver door. This may be done to make it easier to exit the vehicle. See “Easy Exit Driver Seat” under Memory Seats on page 3‑6. This feature can be turned on or off. Press TUNE/MENU when Easy Exit Driver Seat is highlighted. Turn the TUNE/MENU knob to select On or Off. Press TUNE/MENU to confirm and go back to the last menu.

Chime Volume This allows selection of the chime volume level. Press TUNE/MENU when Chime Volume is highlighted. Turn the TUNE/MENU knob to select Normal or High. Press TUNE/MENU to confirm and go back to the last menu.

Reverse Tilt Mirror When on, both the driver and passenger mirrors will tilt downward when the vehicle is shifted to R (Reverse) to improve visibility of the ground near the rear wheels. They will return to their previous driving position when the vehicle is shifted out of R (Reverse), the ignition is turned to OFF, or the vehicle is left in R (Reverse). See Reverse Tilt Mirrors on page 2‑18. Press TUNE/MENU when Reverse Tilt Mirror is highlighted. Turn the TUNE/MENU knob to select On or Off. Press TUNE/MENU to confirm and go back to the last menu.

Chevrolet Malibu Owner Manual - 2013 - CRC - 10/24/12

Black plate (38,1)

5-38

Instruments and Controls

Language Select the Language menu and the following will be displayed: . English French . Spanish Press TUNE/MENU when Language is highlighted. Turn the TUNE/ MENU knob to select the desired language. Press TUNE/MENU to confirm and go back to the last menu. Lighting Select the Lighting menu and the following may be displayed: . Vehicle Locator Lights . Exit Lighting

Vehicle Locator Lights This allows the vehicle locator lights to be turned on or off. The vehicle locator lights come on when unlocking the vehicle with the RKE transmitter.

Press TUNE/MENU when Vehicle Locator Lights is highlighted. Turn the TUNE/MENU knob to select On or Off. Press TUNE/MENU to confirm and go back to the last menu.

Exit Lighting This allows selection of how long the exterior lamps stay on when leaving the vehicle and it is dark outside. Press TUNE/MENU when Exit Lighting is highlighted. Turn the TUNE/MENU knob to select Off, 30 Seconds, 1 Minute, or 2 Minutes. Press TUNE/MENU to confirm and go back to the last menu. Power Door Locks Select Power Door Locks and the following may be displayed: . Unlocked Door Anti Lock Out . Auto Door Unlock . Delayed Door Lock . Auto Door Lock

Unlocked Door Anti Lock Out When on, this feature will keep the driver door from locking when the door is open. If Off is selected, the Delayed Door Lock menu will be available and the door will lock as programmed through this menu. Press TUNE/MENU when Unlocked Door Anti Lock Out is highlighted. Turn the TUNE/MENU knob to select On or Off. Press TUNE/ MENU to confirm and go back to the last menu.

Auto Door Unlock This allows selection of which of the doors will automatically unlock when the vehicle is shifted into P (Park). Press TUNE/MENU when Auto Door Unlock is highlighted. Turn the TUNE/MENU knob to select All Doors, Driver Door, or Off. Press TUNE/MENU to confirm and go back to the last menu.

Chevrolet Malibu Owner Manual - 2013 - CRC - 10/24/12

Black plate (39,1)

Instruments and Controls

5-39

Delayed Door Lock When on, this feature will delay the locking of the doors until five seconds after the last door is closed. Three chimes will signal delayed locking is in use. Press either the power lock button or Q on the RKE transmitter twice to override the delayed locking feature and immediately lock all of the doors. Press TUNE/MENU when Delayed Door Lock is highlighted. Turn the TUNE/MENU knob to select On or Off. Press TUNE/MENU to confirm and go back to the last menu.

Auto Door Lock This allows selection of which of the doors will automatically lock when the vehicle is shifted out of P (Park). Press TUNE/MENU when Auto Door Lock is highlighted. Turn the TUNE/MENU knob to select All Doors, Driver Door, or Off. Press TUNE/MENU to confirm and go back to the last menu.

Remote Locking, Unlocking, Starting Select Remote Locking, Unlocking, Starting and the following may be displayed: . Unlock Feedback (Lights)

Locking Feedback

. Door Unlock Options . Memory Remote Recall . Remote Left in Vehicle Reminder . Relock Remote Door . Passive Door Unlock . Passive Door Lock

Unlock Feedback (Lights) When on, the exterior lamps will flash when unlocking the vehicle with the RKE transmitter. Press TUNE/MENU when Unlock Feedback (Lights) is highlighted. Turn the TUNE/MENU knob to select On or Off. Press TUNE/ MENU to confirm and go back to the last menu.

Locking Feedback This allows selection of what type of feedback is given when locking the vehicle with the RKE transmitter. Press TUNE/MENU when Locking Feedback is highlighted. Turn the TUNE/MENU knob to select Lights and Horn, Lights Only, Horn Only, or Off. Press TUNE/MENU to confirm and go back to the last menu.

Door Unlock Options This allows selection of which doors will unlock when pressing K on the RKE transmitter. Press TUNE/MENU when Door Unlock Options is highlighted. Turn the TUNE/MENU knob to select All Doors or Driver Door Only. When set to Driver Door Only, the driver door will unlock the first time K is pressed and all doors will unlock when K is pressed a second time.

Chevrolet Malibu Owner Manual - 2013 - CRC - 10/24/12

Black plate (40,1)

5-40

Instruments and Controls

When set to All Doors, all of the doors will unlock at the first press of K. Press TUNE/MENU to confirm and go back to the last menu.

Memory Remote Recall This allows the Memory Remote Recall feature to be turned on or off. When on, this feature will recall the current driver's last seat and outside mirror positions upon unlocking the driver door with the RKE transmitter, and opening that door. The current driver is identified when the RKE transmitter is used to unlock the driver door. If keyless access equipped, the recall will occur upon opening the driver door. See “Recalling RKE Memory Positions” under Memory Seats on page 3‑6. Press TUNE/MENU when Memory Remote Recall is highlighted. Turn the TUNE/MENU knob to select On or Off. Press TUNE/MENU to confirm and go back to the last menu.

Remote Left in Vehicle Reminder This allows the Remote Left in Vehicle Reminder feature to be turned on or off. If on, the horn will chirp if a remote is left in the vehicle. Press TUNE/MENU when Remote Left in Vehicle Reminder is highlighted. Turn the TUNE/MENU knob to select On or Off. Press TUNE/MENU to confirm and go back to the last menu.

Relock Remote Door When on, the doors will automatically lock after a period of time if the vehicle is not entered or exited. Press TUNE/MENU when Relock Remote Door is highlighted. Turn the TUNE/MENU knob to select On or Off. Press TUNE/MENU to confirm and go back to the last menu.

Passive Door Unlock This allows selection of which doors are unlocked by pressing the button on the outside door handle. Press TUNE/MENU when Passive Door Unlock is highlighted. Turn the TUNE/MENU knob to select All Doors or Driver Door. Press TUNE/ MENU to confirm and go back to the last menu.

Passive Door Lock This allows selection of turning Passive Locking Off, On or On with feedback. Press TUNE/MENU when Passive Door Lock is highlighted. Turn the TUNE/MENU knob to select Off, On or On with Active Horn Chip. Press TUNE/MENU to confirm and go back to the last menu.

Chevrolet Malibu Owner Manual - 2013 - CRC - 10/24/12

Black plate (41,1)

Instruments and Controls

5-41

Return to Factory Settings Select Return to Factory Settings for the option to return all vehicle personalization to the default settings. Turn the TUNE/MENU knob to select Yes or No. Press TUNE/MENU to confirm and go back to the last menu.

Universal Remote System See Radio Frequency Statement on page 13‑21 for information regarding Part 15 of the Federal Communications Commission (FCC) rules and Industry Canada Standards RSS-GEN/210/220/310.

Universal Remote System Programming

This system provides a way to replace up to three remote control transmitters used to activate devices such as garage door openers, security systems, and home automation devices. Do not use the Universal Remote system with any garage door opener that does not have the stop and reverse feature. This includes any garage door opener model manufactured before April 1,1982. Read the instructions completely before attempting to program the Universal Remote system. Because of the steps involved, it may be helpful to have another person available to assist with programming the Universal Remote system.

If the vehicle has this feature, you will see these buttons with one indicator light next to them in the overhead console.

Chevrolet Malibu Owner Manual - 2013 - CRC - 10/24/12

Black plate (42,1)

5-42

Instruments and Controls

Keep the original hand-held transmitter for use in other vehicles as well as for future Universal Remote system programming. It is also recommended that upon the sale of the vehicle, the programmed Universal Remote system buttons be erased for security purposes. See “Erasing Universal Remote System Buttons” later in this section. When programming a garage door, park outside of the garage. Park directly in line with and facing the garage door opener motor-head or gate motor-head. Be sure that people and objects are clear of the garage door or gate being programmed. It is recommended that a new battery be installed in the hand-held transmitter for quicker and more accurate transmission of the radio-frequency signal.

Programming the Universal Remote System For questions or help programming the Universal Remote system, call 1-800-355-3515 or go to www.homelink.com. Programming a garage door opener involves time-sensitive actions, so read the entire procedure before starting. Otherwise, the device will time out and the procedure will have to be repeated. To program up to three devices: 1. Hold the end of the hand-held

transmitter about 3 to 8 cm (1 to 3 in) away from the Universal Remote system buttons while keeping the indicator light in view. The hand-held transmitter was supplied by the manufacturer of the garage door opener receiver (motor-head unit).

2. At the same time, press and

hold both the hand-held transmitter button and one of the three Universal Remote system buttons to be used to operate the garage door. Do not release the Universal Remote system button or the hand-held transmitter button until the indicator light changes from a slowly to a rapidly flashing light. You now may release both buttons. Some entry gates and garage door openers may require substitution of Step 2 with the procedure noted in “Gate Operator and Canadian Programming” later in this section.

Chevrolet Malibu Owner Manual - 2013 - CRC - 10/24/12

Black plate (43,1)

Instruments and Controls

5-43

3. Press and hold for five seconds

the newly trained Universal Remote system button (the button selected in Step 2) while observing the indicator light and garage door activation.

If the indicator light stays on continuously or the garage door starts to move when the Universal Remote system button is pressed and released, then the programming is complete. There is no need to continue programming Steps 4–6. If the Universal Remote system indicator light blinks rapidly for two seconds, then turns to a constant light and the garage door does not move, continue with programming Steps 4–6.

It may be helpful to have another person assist with the remaining Steps 4–6.

5. Firmly press and release the

6.

“Learn” or “Smart” Button

4. After Steps 1–3 have been

completed, locate the “Learn” or “Smart” button inside the garage on the garage door opener receiver (motor-head unit). The name and color of the button may vary by manufacturer.

“Learn” or “Smart” button. After pressing this button, you will have 30 seconds to complete Step 6. Immediately return to the vehicle. Firmly press and hold for two seconds the Universal Remote system button, selected in Step 2 to control the garage door, and then release it. If the garage door does not move or the lamp on the garage door opener receiver (motor-head unit) does not flash, press and hold the same button a second time for two seconds, then release it. Again, if the door does not move or the garage door lamp does not flash, press and hold the same button a third time for two seconds, then release.

Chevrolet Malibu Owner Manual - 2013 - CRC - 10/24/12

Black plate (44,1)

5-44

Instruments and Controls

The Universal Remote system should now activate the garage door. To program the remaining two Universal Remote system buttons, begin with Step 1 of “Programming the Universal Remote System.” Gate Operator and Canadian Programming If you have questions or need help programming the Universal Remote system, call 1-800-355-3515 or go to www.homelink.com. Canadian radio-frequency laws require transmitter signals to time out or quit after several seconds of transmission. This may not be long enough for the Universal Remote system to pick up the signal during programming. Similarly, some U.S. gate operators are manufactured to time out in the same manner.

If you live in Canada, or you are having difficulty programming a gate operator or garage door opener by using the “Programming the Universal Remote System” procedures, regardless of where you live, replace Step 2 under “Programming the Universal Remote System” with the following: Continue to press and hold the Universal Remote system button while you press and release every two seconds (cycle) the hand-held transmitter button until the frequency signal has been successfully accepted by the Universal Remote system. The Universal Remote system indicator light will flash slowly at first and then rapidly. Proceed with Step 3 under “Programming the Universal Remote System” to complete.

Universal Remote System Operation

Using the Universal Remote System Press and hold the appropriate Universal Remote system button for at least half of a second. The indicator light will come on while the signal is being transmitted. Erasing Universal Remote System Buttons All programmed buttons should be erased when the vehicle is sold or the lease ends. To erase all programmed buttons on the Universal Remote system device: 1. Press and hold down the two

outside buttons until the indicator light begins to flash. This should take about 10 seconds.

2. Release both buttons.

Chevrolet Malibu Owner Manual - 2013 - CRC - 10/24/12

Black plate (45,1)

Instruments and Controls

5-45

Reprogramming a Single Universal Remote System Button To reprogram any of the three Universal Remote system buttons: 1. Press and hold the desired

Universal Remote system button. Do not release the button.

2. The indicator light will begin to flash after 20 seconds. Without releasing the button, proceed with Step 1 under “Programming the Universal Remote System.” If you have questions or need help programming the Universal Remote system, call 1-800-355-3515 or go to www.homelink.com. You may also call the customer assistance phone number under Customer Assistance Offices (U.S. and Canada) on page 13‑5 or Customer Assistance Offices (Mexico) on page 13‑5.

Chevrolet Malibu Owner Manual - 2013 - CRC - 10/24/12

Black plate (46,1)

5-46

Instruments and Controls

2 NOTES

Chevrolet Malibu Owner Manual - 2013 - CRC - 10/24/12

Black plate (1,1)

Lighting

Exterior Lighting

Exterior Lamp Controls . . . . . . . . 6-1
Exterior Lamps Off

Reminder . . . . . . . . . . . . . . . . . . . . 6-2

Headlamp High/Low-Beam

Changer . . . . . . . . . . . . . . . . . . . . . 6-2
Flash-to-Pass . . . . . . . . . . . . . . . . . 6-2
Daytime Running

Lamps (DRL) . . . . . . . . . . . . . . . . 6-2

Automatic Headlamp

System . . . . . . . . . . . . . . . . . . . . . . 6-3
Hazard Warning Flashers . . . . . 6-4
Turn and Lane-Change

Signals . . . . . . . . . . . . . . . . . . . . . . 6-4
Fog Lamps . . . . . . . . . . . . . . . . . . . . 6-4

Interior Lighting

Instrument Panel Illumination

Control . . . . . . . . . . . . . . . . . . . . . . 6-5
Courtesy Lamps . . . . . . . . . . . . . . 6-5
Dome Lamps . . . . . . . . . . . . . . . . . 6-5
Reading Lamps . . . . . . . . . . . . . . . 6-6

Lighting Features

Entry Lighting . . . . . . . . . . . . . . . . . 6-6
Exit Lighting . . . . . . . . . . . . . . . . . . . 6-7
Battery Load Management . . . . 6-7

Lighting

6-1

Exterior Lighting

Exterior Lamp Controls

The exterior lamp control is on the instrument panel on the left side of the steering wheel. Turn the control to the following positions: O (Off): Turns off the exterior lamps. The knob returns to the AUTO position after it is released. Turn to O again to reactivate the AUTO mode.

Chevrolet Malibu Owner Manual - 2013 - CRC - 10/24/12

Black plate (2,1)

6-2

Lighting

In Canada, the headlamps will automatically reactivate when the vehicle is shifted out of P (Park). AUTO (Automatic): Automatically turns the exterior lamps on and off, depending on outside lighting. ; (Parking Lamps): Turns on the parking lamps together with the following: . Sidemarker Lamps

Taillamps License Plate Lamps Instrument Panel Lights

2 (Headlamps): Turns on the headlamps together with the following: . Sidemarker Lamps

Taillamps License Plate Lamps Instrument Panel Lights

. Parking Lamps

Exterior Lamps Off Reminder A warning chime sounds if the driver door is opened while the ignition is off and the exterior lamps are on.

Headlamp High/ Low-Beam Changer 2 3 (Headlamp High/Low-Beam Changer): Push the turn signal lever away from you and release, to turn the high beams on. To return to low beams, push the lever again or pull it toward you and release.

This indicator light turns on in the instrument cluster when the high-beam headlamps are on.

Flash-to-Pass To flash the high beams, pull the turn signal lever toward you, and release.

Daytime Running Lamps (DRL) Daytime running lamps (DRL) can make it easier for others to see the front of your vehicle during the day. Fully functional daytime running lamps are required on all vehicles first sold in Canada. The DRL system turns on the low-beam headlamps at a reduced brightness. For vehicles with High Intensity Discharge (HID) headlamps, there is a dedicated DRL. The DRL will come on when all of the following conditions are met:

The ignition is on. The exterior lamp control is in AUTO.

Chevrolet Malibu Owner Manual - 2013 - CRC - 10/24/12

Black plate (3,1)

The light sensor determines it is daytime. The vehicle is not in P (Park).

When the DRL are on, the taillamps, sidemarker lamps, instrument panel lights, and other lamps will not be on. The DRL turn off when the headlamps are turned to O or the ignition is off. This vehicle may have a DRL disabling function. When the DRL are on and a turn signal is activated, the DRL on that side will be off until the turn signal goes off.

Automatic Headlamp System When the exterior lamp control is set to AUTO and it is dark enough outside, the headlamps come on automatically.

There is a light sensor on top of the instrument panel. Do not cover the sensor, otherwise the headlamps will come on when they are not needed. The system may also turn on the headlamps when driving through a parking garage or tunnel. When it is bright enough outside, the headlamps will turn off or may change to Daytime Running Lamps (DRL).

Lighting

6-3

The automatic headlamp system turns off when the exterior lamp control is turned to O or the ignition is off. Lights On with Wipers If the windshield wipers are activated in daylight with the engine on, and the exterior lamp control is in AUTO, the headlamps, parking lamps, and other exterior lamps come on. The transition time for the lamps coming on varies based on wiper speed. When the wipers are not operating, these lamps turn off. Move the exterior lamp control to P or ; to disable this feature.

Chevrolet Malibu Owner Manual - 2013 - CRC - 10/24/12

Black plate (4,1)

6-4

Lighting

Hazard Warning Flashers

Turn and Lane-Change Signals

| (Hazard Warning Flashers): Press this button to make the front and rear turn signal lamps flash on and off. Press again to turn the flashers off. The hazard warning flashers turn on automatically if the airbags deploy.

Move the turn signal lever all the way up or down to signal a turn. An arrow on the instrument cluster flashes in the direction of the turn or lane change. Raise or lower the lever until the arrow starts to flash to signal a lane change. Hold it there until the lane change is completed. If the lever is briefly pressed and released, the turn signal flashes three times.

The turn signal can be turned off manually by moving the lever back to its original position. If after signaling a turn or lane change, the arrow flashes rapidly or does not come on, a signal bulb may be burned out. Have any burned out bulbs replaced. If a bulb is not burned out, check the fuse. See Fuses on page 10‑38.

Fog Lamps

To turn on the fog lamps, the ignition and the headlamps or parking lamps must be on.

Chevrolet Malibu Owner Manual - 2013 - CRC - 10/24/12

Black plate (5,1)

Interior Lighting

Instrument Panel Illumination Control

If the fog lamps are turned on while the exterior lamp control is in the AUTO position, the headlamps come on automatically. # (Fog Lamps): Press to turn on or off. An indicator light on the instrument cluster comes on when the fog lamps are on. Some localities have laws that require the headlamps to be on along with the fog lamps.

Lighting

6-5

Courtesy Lamps The courtesy lamps come on automatically when any door is opened and the dome lamp is in the door position.

Dome Lamps

The brightness of the instrument panel lighting and steering wheel controls can be adjusted. D (Instrument Panel Illumination): Move and hold the thumbwheel up or down to brighten or dim the lights.

The interior lamps control in the overhead console controls both the front and rear interior lamps.

Chevrolet Malibu Owner Manual - 2013 - CRC - 10/24/12

Black plate (6,1)

6-6

Lighting

To operate, press the buttons: E (Off): Turns the lamps off. 1 (Door): Turns the lamps on when any door is opened. + (On): Keeps the lamps on all the time.

Reading Lamps There are front and rear reading lamps in the overhead console and the headliner.

Lighting Features

Entry Lighting The headlamps, taillamps, license plate lamps, back-up lamps, dome lamps, and most of the interior lights turn on briefly when the Remote Keyless Entry (RKE) transmitter K button is pressed, or when the door handle is pulled on a keyless access vehicle. See Ignition Positions (Key Access) on page 9‑15 or Ignition Positions (Keyless Access) on page 9‑17. After about 30 seconds the exterior lamps turn off, then the dome lamps and remaining interior lights dim to off. Entry lighting can be disabled manually by changing the ignition out of the OFF position, or by pressing the RKE transmitter Q button. This feature can be changed. See Vehicle Personalization on page 5‑36.

Front Reading Lamps

Rear Reading Lamps

# or $ (Reading Lamps): Press the button near each lamp to turn it on or off.

Chevrolet Malibu Owner Manual - 2013 - CRC - 10/24/12

Black plate (7,1)

Exit Lighting The headlamps, taillamps, parking lamps, back-up lamps, and license plate lamps come on at night, or in areas with limited lighting, when the key is removed from the ignition. The dome lamps also come on when the key is removed from the ignition. The exterior lights and dome lamps remain on after the door is closed for a set amount of time, then automatically turn off. For vehicles with keyless access, the exterior lamps automatically turn on when a door is opened after the ignition is turned off. The dome lamps come on after the ignition is changed to the OFF position. See Ignition Positions (Key Access) on page 9‑15 or Ignition Positions (Keyless Access) on page 9‑17. The exterior lamps turn off immediately by turning the exterior lamps control off. This feature can be changed. See Vehicle Personalization on page 5‑36.

Battery Load Management The vehicle has Electric Power Management (EPM), which estimates the battery's temperature and state of charge. It then adjusts the voltage for best performance and extended life of the battery.